LG | MK2030F | Installation manual | LG MK2030F Installation Manual

ELECTRICAL CONNECTION
INSTRUCTIONS FOR THE INSTALLATION OF
MICROWAVE APPLIANCE FRAME
Once the oven is securely attached it is ready for plugging in and must be
connected to a properly installed safety socket. If any relocation of a socket or
exchange of connection line is required it must be made by a qualified electric titter
taking into consideration the appropriate regulations. If after installation the
appliance’s plug is too short a separator controlling all poles must be used at the
installation side with a contact opening of at least 3mm with regard to satisfying the
necessary safety regulations.
PLEASE READ CAREFULLY BEFORE INSTALLATION
1. The cabinet which is used for the installation of the microwave oven
appliance should be securely attached to the back panel to ensure
stability.
PARTS LIST
2. The cabinet is to be used for microwave oven with a maximum weight of
approximately 30kg.
(A) Trim Frame
(B) Bottom Duct
(C) Side Duct
(D) 4 mm x 12 mm Round-Head Screws
(E) 4 mm x 14 mm Flat-Head Screws
(F) Anti-Tip Brace
(G) Anti-Tip Bracket
(H) Upper Duct
(I) Top Bracket
(J) Bottom Bracket
(K) Templates
3. If the microwave is installed directly above a refrigerator or freezer
cabinet pay attention to their installation instructions, a ventilation duct
must also be in place.
4. If the microwave appliance is installed directly above an electric built in
oven the appropriate electric oven installation guide must be observed.
CAUTION : In the case of frequent or particularly long grill operation
times of the electric oven (especially with door open), the shape and
colour of the microwave oven and installation frame can change.
1 Each
1 Each
1 Each
23 Each
6 Each
1 Each
1 Each
1 Each
1 Each
1 Each
2 Each
5. If the microwave oven is used again as a ‘table appliance all appropriate
detachable accessories must be removed.
6. The oven should not be used as a storage place for food, cooking
utensils etc. In the case of misuse damage or hazard could occur.
7. If a fault occurs to an electronic or electrical component, the oven can
only be turned off by pulling out the mains plug or appropriate circuit
breaker (upstream automatic fuse).
K
P/No. :MFL38268403
1
Printed in China
FIG 1
1.DIMENSIONS OF THE INSTALLATION OPENING (FIG 1)
11⁄ 8″ Overlap
The following opening dimensions in feet must be available in the
installation cabinet :
HEIGHT :163⁄4.″ , WIDTH : 251⁄ 2″. , DEPTH : 191⁄ 2″. or 22.
Depth
27″ Models:11⁄ 16″ overlap
30″ Models: 21⁄ 16″ overlap
WARNING: This trim kit uses air flow from the top, bottom and sides of the trim frame.
Blocking the air flow can cause the microwave to function improperly and
may cause damage to the microwave.
Allow a 1″clearance beyond the edge of the trim frame to provide proper air flow.
On 27″ models, allow 11/8″at the top,11/16 ″ on the sides and 11/4″ at the bottom for
overlap of the Trim Frame over the edges of the cutout.On 30 ″ models, allow
Height
Width
11/8″at the top, 2 1/16″ on the sides and 11/4″ at the bottom for overlap of the
Trim Frame over the edges of the cutout.
FOR INSTALLATION ABOVE A BUILT-IN OVEN
Bottom of trim kit
must be minimum
of 36 ″from floor
Microwave oven should be installed on a 3/8″ plywood base and support
by 2x4 or 1x2 equivalent runnerson all sides. Base must be capable of
supporting aminimum of 100 lbs (45.3 kg).
1″ Clearance
beyond trim frame
(FIG
2)
(on
all sides)
11⁄ 4″ Overlap
3″ Min.
FIG 2
D
DIMENSIONS:
A = 11⁄ 2″
B = 3″
C = 183⁄ 16″
D = 1/2″
2.INSTALL THE ANTI-TIP BRACE (FIG 2)
1.Draw a line on the cutout floor at the center of the cutout, and extend the line
1/2″ down the face of the cabinet.
Round-head
screws (2)
Anti-Tip Brace
2.Draw a line on the top front face of the cabinet at the center of the cutout. The
line should extend 1/2″ up the face of the cabinet. This center line will be used
for mounting the top bracket (see step 7).
3.Fold or cut the front edge of the template, along the front guide line. Place
the template flush along the front edge of the cutout floor, aligning the center
line of the template with the center line of the cutout floor. Mark the center
positions with an awl or center punch for the anti-tip brace location as shown.
D
FIG 3
3.INSTALL THE ANTI-TIP BRACKET AND BOTTOM DUCT (FIG 3)
1.Disconnect the microwave oven before proceeding with the installation.
2.Fasten the anti-tip bracket to the bottom duct by using four round-head screws.
3.Remove any loose items inside the microwave oven,including the turntable
and turntable support.Carefully turn the microwave upside down.
4.Install bottom duct with four round-head screws as shown.
Round-Head Screws
Front
Rear
Round-Head Screws (4)
Microwave Oven Upside Down
2
FIG 4
4.INSTALL SIDE DUCT AND UPPER DUCT( FIG 4)
Upper Duct
1.Connect the side duct to the upper duct as shown.
(1 ) Insert projecting tabs of the upper duct into the holes of the side duct.
(2) Bend the tabs up with caution as shown.
NOTE: Remove any oil or dirt on the surface of the microwave oven before the
ducts are attached.
2.Set the microwave upright, being careful not to bend the front flange. Remove the one
existing screw from the left side of the microwave oven.
3 Tabs
Cutout
Opening
(1)
3.As indicated on the supplied template, fold or cut along the “cut lines” and place the
template on top of the microwave oven. By aligning the template with the outside edges
of the oven, you will see exactly where to place the upper duct assembly. Peel off the
backing from the double-sided tape. Carefully position the side duct and upper duct
assembly on the microwave cabinet, aligning with the bottom screw hole. Press down
firmly on the ducts. Fasten the duct assembly to the left side of the cabinet with the
screw removed above.
Side Duct
5.INSTALL MICROWAVE OVEN INTO CABINET (FIG 5)
Round-Head
(2)
Screws
Existing Screw (1)
FIG 5
1.Slide the microwave oven part way into the cabinet opening.
2.Plug in the microwave oven.
3.The anti-tip bracket must be flat to the cutout floor to engage correctly with the
anti-tip brace as shown. Carefully slide the microwave back, making sure the
power cord is not mashed or cut.
Bottom Duct
4.Center the microwave oven within the cutout opening and slide the microwave
oven in place, engaging the anti-tip brace.
5.Ensure the microwave oven is accurately centered.
.
Anti-Tip Assembly
Anti-Tip
Brace
Anti-Tip Bracket
Ensure
FIGthat
6
Top Bracket
is Level
6.CHECK LEVELING (FIG 6)
1.Check the leveling by placing a level at the front and sides of the microwave.
It may be necessary to add wood shims under the bottom duct to level the
microwave front to back or side to side.
Align Center
Lines on
Cabinet and
Top Bracket
Mark Screw
Hole Locations
(also on left
side of
bracket)
3
Round-Head
Screw
FIG 7
7.INSTALL THE TOP BRACKET (FIG 7)
1.Place the top bracket flange on top of the upper duct with the opening of the top
bracket lined up with the opening on the upper duct.
2.Align the center line marking on the top bracket with the center line drawn on the
top front face of the cabinet at the center of the cutout.
3.Ensure the top bracket is level and mark screw hole locations on the cabinet face.
4.Drill pilot holes through the side holes in the top bracket. Secure the top bracket to
the cabinet using four round-head screws (see illustration in step 8).
Align Center
Lines on
Cabinet and
Top Bracket
Ensure that
Top Bracket
is Level
Mark Screw
Hole Locations
(also on left
side of
bracket)
Cutout
Opening
Round-Head
Screws
8.INSTALL THE BOTTOM BRACKET AND SECURE THE
TOP BRACKET (FIG 8)
FIG 8
1.Drill pilot holes through the three holes on the front flange of the bottom
duct assembly.
2.Hold the bottom bracket against the front flange of the bottom duct assembly,
lining up the three holes in the bottom bracket with the three holes in the bottom
duct. Screw in three round-head screws. Drill pilot holes through the four holes
in the tabs on the sides of the bottom bracket. Screw in four round-head screws.
Cutout
Opening
Flat -Head
Screws
9.INSTALL THE TRIM FRAME (FIG 9)
Positioning
Flange
Round-Head
Screws
FIG 9
1.Place the trim frame over the microwave oven with the curved edge at the top.
.
2.Press the trim frame into the opening until all sides snap into place.
3.Open the microwave oven door..Secure the trim frame using four flat-head screws
(two on the inside top and two on the inside bottom).
Ensure that
Top Bracket
is Level
Align Center
Lines on
Cabinet and
Top Bracket
Flat-Head Screws
Mark Screw
Hole Locations
(also on left
side of
bracket)
10.REPLACE ANY LOOSE ITEMS
1.Your trim kit is now fully installed. Replace the turntable and turntable support that
were removed from the inside of the microwave oven.
2.Keep these installation instructions and extra screws for future reference and need.
Do not place them in the microwave oven.
3.Replace house fuse or close circuit breaker.
Flat-Head Screws
4
Download PDF

advertising