GE Monogram ZUGSS2 Installation Instructions


Add to my manuals
8 Pages

advertisement

GE Monogram ZUGSS2 Installation Instructions | Manualzz
Installation
Instructions
ZUGPP2 and
ZUGSS2 Trim Kit
Stainless Steel
Unified Grille Panel
This kit provides for the installation of a stainless steel unified
grille panel. The panel will span the combined width
of a side-by-side installation.
Completion Time: Allow approximately 2 hours to install
this kit.
IMPORTANT: 2 People are required to install this kit.
Disconnect power before you begin.
THE INSTALLATION SPACE
• The installation space must be 71-1/2" wide.
• The water and electrical locations for each product
must be located as shown.
• A separate 115V, 60Hz., 15 or 20 amp power supply
is recommended for each product.
Note: Additional cutout width may be required when
side panels are used. Add side panel thickness to the
finished cutout to calculate rough-in width.
71-1/2" Finished Width
2-5/16"
Electrical
Wall View
24-3/16"
5-1/2"
5-1/2"
9"
9"
Electrical
Area
24" Minimum
Cutout Depth
84-1/2" max.
83-1/2" min.
Finished
Opening
Cold Water
Supply
3-1/2"
3-1/2"
3-1/2"
5"
5"
Tools and materials Required:
• #1 and #2 Phillips screwdrivers
• Safety glasses
• Gloves to protect against sharp edges
Parts List:
A. Stainless steel unified grille panel
B. Foam spacer pads
C. 10 Black #8-32 x 3/8” screws
3-1/2"
5"
3-1/2"
3-1/2"
75-1/2" From
Floor to Bottom
of Electrical Area
Cold Water
Supply
5"
3-1/2"
3-1/2" 3-1/2"
A
C
B
3-1/2"
STEP 1 INSTALL FOAM SPACER PADS (Bottom–Mount and All Refrigerator/All Freezer Models)
CAUTION: Handle parts with care to
avoid scratching.
PRUDENCE :
Manipulez les pièces
soigneusement pour éviter de les rayer.
Apply the supplied foam spacer pads (B)
to the mating side of one product as shown.
Foam Spacer Pads
STEP 2 INSTALL ANTI-TIP BRACKET
BOTTOM FREEZER MODELS ONLY
WARNING: ANTI-TIP PRECAUTIONS
Brackets
Required
These refrigerators are top-heavy and must be secured
to prevent the possibility of tipping forward.
Soffit
Block
ATTENTION :
PRECAUTIONS CONTRE
LES BASCULEMENTS
Le réfrigérateur est beaucoup plus lourd en haut
et il faut le maintenir en place pour éviter la possibilité
de son basculement vers l’avant.
Height
From Floor
to Bottom
of Wood
Block
• Cut a 2"x4" block 71" long. Secure the 2"x4" to the 4
mounting brackets provided using #12 or #14 wood
screws.
• Secure the brackets with wood block to the back wall
so that it is 84" (or your installation height) from
the finished floor. Use #12 or #14 wood screws.
See illustration.
Side View
Mounting Bracket
• Screws must penetrate at least one inch into vertical
wall studs.
• Gently push refrigerator into the opening with hands
against front corners.
2 x 4 Cut to
35" Length
Note: When the refrigerators are installed under a soffit,
or if there is not enough height for this method of security,
brackets cannot be used. Proceed to “Level the
Refrigerator” and to “Secure side trim to cabinetry.”
The refrigerators must be secured to prevent tipping.
Installation
Height
From Floor
Wood Screws Mounted into
Vertical Wood Studs
2
Brackets
Not Required
Beneath a Soffit
STEP 2 INSTALL ANTI-TIP BRACKET
ALL REFRIGERATOR, ALL FREEZER
“X” MODELS ONLY
WARNING:
ANTI-TIP PRECAUTIONS
The unit is top-heavy and must be secured to prevent
the possibility of tipping forward.
ATTENTION :
PRECAUTIONS CONTRE
LES BASCULEMENTS
L’appareil ménager est beaucoup plus lourd en haut
et il faut le maintenir en place pour éviter la possibilité
de son basculement vers l’avant.
• The kit supplied with the unit contains 3 (2 required,
1 extra) lag bolts and 5 (4 required, 1 extra) toggles
with bolts. The wall bracket will be attached
to the wall in 4 places.
• Measure the opening where the unit is to be installed.
Mark the center with a vertical line.
• Measure up 81-1/2" from the floor. Mark this point
on the wall.
• Using a level, draw a horizontal line on the wall
at this height.
• Locate at least 2 studs on the back wall. Mark these
points on the horizontal line.
• Place the bottom of the wall bracket with tabs
on the horizontal line. Align the center notch
on the bracket with the center line on the wall.
• The anti-tip wall bracket has a series of holes.
Select 2 holes that match with the located studs.
Make sure the holes selected are on the center
of the studs. Mark the wall at these points.
81-1/2"
To Floor
Center
Wall Bracket
Line on Wall
• Mark an additional hole at each end of the bracket.
If one of the studs is closer to the end of the bracket,
mark an additional hole towards the center
of the bracket.
• Drill 1/2" holes into the wallboard at the locations
marked for the toggles to be mounted (not the stud
markings).
• Drill 3/16" holes into wooden studs where marked.
If steel stud construction, drill 1/2" holes into the studs
where marked. You will use 2 toggles with the metal
studs.
Two Additional
Hole Locations at
Ends of Brackets
Wall Studs
Line on Wall
Center
3
STEP 2 INSTALL ANTI-TIP BRACKET (cont.)
ALL REFRIGERATOR, ALL FREEZER
“X” MODELS ONLY
Install Wall Toggles:
The wall toggles and bolts can be ordered as Service
Kit #WR49X10193. Wall toggles are installed in the drywall
and metal studs for stability. Install the wall toggles
as follows:
• Drill 1/2" holes at the wall markings made in the holes
at the ends of the wall bracket.
• Hold the metal channel flat against the plastic straps
and slide the channel through the hole.
Install Screws and Bolts:
• Have someone hold the wall bracket centered in place
with each of the holes aligned with the correct opening
in the bracket and level with the horizontal line.
• Insert the lag screws through the bracket and into
the stud. Tighten with a wrench.
• Insert the bolts into the toggle by hand until snug.
Tighten with a wrench.
Wood Stud
Plastic Straps
Lag Screw
Metal Channel
• Gently pull back at the ends of the plastic straps
to make the channel rest flush behind the wall.
• Hold the ends of the straps in one hand and slide
the plastic cap along the straps until the flange
of the cap is flush with the wall.
Anti-Tip Wall Bracket
Cap
Drywall or
Steel Stud
Bolt
• Place your thumb between the plastic straps and bend
up and down to snap the straps off at the wall.
Wall Toggle
Anti-Tip Wall Bracket
Remove Grilles for Access to Power Cord
and Anti-tip Locking Hooks
Fresh Food Unit
• Open the access door.
• Using a 1/4" hex driver, remove the 3 screws
at the bottom of the grille.
• Pull the bottom of the grille forward, down and out
to remove.
Screws
4
STEP 2 INSTALL ANTI-TIP BRACKET (cont.)
ALL REFRIGERATOR, ALL FREEZER
“X” MODELS ONLY
Freezer Unit
• Open the access door.
• Using a 1/4" hex driver, remove the 2 screws
at the bottom of the grille on the right.
• Pull the bottom of the grille forward, down and out
to remove.
• Using a 1/4" hex driver, remove the screw on the left
side of the grille.
• The grille is aluminum and will bend easily. Gently pull
forward on the left side of the grille to open for access.
This grille will not be completely removed.
Remove Grilles for Access to Power Cord and Anti-tip
Locking Hooks
Power Cord
Locate the power cord inside the left cavity. If it has not
been adjusted so the plug is easily accessible, do so now.
“L” Bolt
Left Grille Open
Power Cord Location
Screws
STEP 3 LEVEL REFRIGERATORS
Both products MUST BE LEVEL AND PLUMB with each
other and with adjacent cabinetry on each side.
• Adjust carefully. Both models have 4-point leveling.
The front is supported by leveling legs, the rear
is supported by wheels. Both are accessible from
the front of the refrigerator.
• For bottom-mount refrigerator models only, turn
the 7/16" hex nut located above the front wheels
to raise or lower the back of the refrigerator until
it just barely touches the 2 x 4 blocks.
• For All Refrigerator/All Freezer models, turn the 7/16”
hex nut located above the front wheels to raise
or lower the unit to close the gap at the top
of the cabinets.
Hex Nut Adjusts
Rear Wheels
Leveling Leg
• For front leveling, use a 1-1/4" open-ended wrench
to turn the leveling legs.
The inside case trims must be aligned without gaps
at the top and bottom.
5
STEP 4 SECURE UNIT TO WALL
ALL REFRIGERATOR, ALL FREEZER
“X” MODELS ONLY
• The “L” rods can be found in the upper left and right
corners of the unit in the access compartment.
Look through the access compartment to make
sure the rods line up with the anti-tip bracket.
• There are 2 washers and a hair pin cotter per rod.
Remove the washers and hair pin cotter from the end
of the rod.
• Rotate and move the “L” rod into the slot in the anti-tip
bracket tab. Once it is in the slot, rotate the “L” rod
so the hook portion is pointing down. The holes
at the front end of the rod should be in a vertical
position. Do this to both sides.
• Pull out on the end of the rod to take make sure
it is secure in the bracket.
• Locate the hole on the rod that is closest to the unit.
A hair pin cotter will be put through this hole to secure
the rod. If this hole appears to be too far away for
a snug fit against the unit, add the washers one
at a time until the pin will fit tightly into the hole.
• Align the straight section of the pin with the hole from
the underside of the rod. Push the pin up until it snaps
into position. Pliers may be used. NOTE: The hair pin
cotter must be vertical when this step is completed to
ensure the “L” rod is engaged in the bracket.
• Check the rod for tightness by pulling forward.
If the rod moves, remove the hair pin cotter and place
another washer on the rod. Reinsert the pin.
• Bend the left grille back into place (freezer only) and
replace the screws.
• Replace the flat grille panel by sliding it under the
flange at the top of the access compartment and
pushing the grille back into place. Replace screws.
“L” Rod Pointing Down
Engaged in Bracket
“L” Rod
Washer
Hair Pin Cotter
Is Vertical
“L” Rod
Wall Bracket
6
STEP 5 SECURE SIDE TRIM
TO CABINETRY
• Whenever possible, perform this additional step.
• Raise the grille panels to access cabinet side trims.
• Drill hole in trim and drive screw through the trim
and into each adjacent cabinet.
Drive Screws
through Case Trim and Into
Adjacent Cabinets
STEP 6 REMOVE BOTH GRILLE
PANEL FRAMES
• Grasp grille panel at the center, lift up to stop position.
• Remove 3 screws holding the grille panel frame
to the hinge on each side. Lift grille panel off
the hinges. Discard both panels and screws.
Grille Panel
Leave hinges in open position. Do not push hinges back.
Remove
3 Screws
STEP 7 INSTALL GRILLE PANEL
TWO PEOPLE ARE REQUIRED TO INSTALL
THE GRILLE PANEL.
Grille Panel
• Push all four hinges on the grille panel to the open position.
• Hold the unified grille panel against the left side of the
opening. Drive 3 screws through the hinge and into the
back panel. Install the right side hinge. Then install the
center hinges.
Loosen 2
Screws to
Adjust Grille
Panel
• Grasp grille panel at the center and pull down to close.
The panel should align evenly with the beveled side
of the door.
NOTE: To adjust the grille panel backward or forward,
loosen the 2 attachment screws on all 4 hinges. Slide
the grille panel outward or to the back. Tighten the screws.
7
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance
and specifications are subject to change without notice.
NOTA: Mientras efectúa las instalaciones descriptas
en este libro, deben utilizarse gafas o lentes de seguridad.
NOTA: La mejora de los productos es un esfuerzo continuo
para General Electric. Por lo tanto, los materiales,
la apariencia y las especificaciones pueden sufrir cambios
sin previo aviso.
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225
ge.com
31-46526-2
224D1889P011
09-08 JR
8

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement