GE | JXHC1 | Installation instructions | GE JXHC1 Installation Instructions

Installation
Instructions
Range Hood
Power Cord Kit
JXHC1
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
WARNING
WARNING
Use in unapproved appliance may result in risk of fire
or electric shock. This range hood cord connection
kit should be used only with GE series range hood
models AV447, JN327, JV338, JV247, JV248, JV347,
JV348, JV367, JV566, JV565, JV535, JV536, JV635,
JV636, JV665, JV666, JVE40 and RN328.
Improper grounding can result in a risk of electric shock.
The appliance must be grounded. The plug must be
plugged into an outlet that is properly installed and
grounded. Consult a qualified electrician if the grounding
instructions are not completely understood, or if doubt
exists as to whether the appliance is properly grounded.
Do not use an extension cord. If the power supply cord
is too short, have a qualified electrician install an outlet
near the appliance.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
‡
IMPORTANT – Save these instructions for local
inspector’s use.
‡
IMPORTANT – Observe all governing codes and
‡
Note to Installer – Be sure to leave these
TOOLS YOU WILL NEED
ordinances.
Flat blade and
Phillips head screwdrivers
instructions with the Consumer.
‡ Note to Consumer – Keep these instructions
for future reference.
‡ Skill Level – Installation of this power cord kit
requires basic mechanical skills. Proper installation is
the responsibility of the installer. Product failure due
to improper installation in not covered under the GE
Appliance Warranty.
Wire cutters/
strippers
1/4" Nutdriver
PARTS INCLUDED
PART
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an
electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the
electric current. This appliance is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
QUANTITY
Power Cord with Strain Relief
1
Wire Nuts
3
Installation Instructions
1
READ AND SAVE THESE INSTRUCTIONS
1
Installation Instructions
5 CONNECT THE CORD WIRES
1 REMOVE CONNECTION BOX COVER
Locate the hood connection box and remove its cover.
Inspect the junction box wires to determine the type of
connections that should be made.
For hoods with a ground screw:
A Connect the green ground wire to the green ground
screw.
B Using the wire nuts provided, connect the black
power cord lead to the stripped black lead and the
white power cord lead to the stripped white lead in
the connection box.
C All electrical connections should be inspected
carefully before replacing the connection box cover.
For hoods with a ground wire:
A Using the (2) wire nuts provided, connect the black
power cord lead to the black junction box lead.
Connect the white power cord lead to the white
junction box lead.
B Locate the power cord green ground wire, and cut off
the ring terminal and strip 1/2" of insulation.
C Using the third wire nut, connect the power cord
ground wire to the green junction box lead.
D All electrical connections should be inspected
carefully before replacing the junction box cover.
2 REMOVE KNOCKOUT
Insert the blade of a flat blade screwdriver into the
preferred knockout slot and bend until the knockout
is removed.
3 THREAD WIRES THROUGH THE
KNOCKOUT
Thread the cord wires through the knockout hole.
6 REPLACE CONNECTION
BOX COVER
Replace the connection box cover using the screws
removed in Step 1.
4 PULL CORD THROUGH THE
KNOCKOUT
7 INSTALL HOOD
From inside of the hood junction box, thread wires
through the strain relief nut and tighten down nut until
secure.
Return to and proceed with the Installation Instructions
to install the range hood.
2
49-80087-7 07-13 GE
Printed in China
Download PDF

advertising