Sharp | SKMD24F0AS | Flush Kit Installation Instructions | Sharp SKMD24F0AS Flush Kit Installation Instructions

24" Flush Mount Deflector Vent: SKMD24F0AS
INSTALLATION INSTRUCTIONS
Parts includes:
Important notes to the installer
Qty.
• Read all of the Installation Manual that is included with
the Microwave Drawer before installing in the flush mount
configuration.
1
• Observe all governing codes, ordinances, and safety
instructions.
• Be sure to leave these instructions with the consumer.
2
Part number
PREF-B019MRP0
Flush Mount
Deflector Vent
LX-CZB055MRE0
Mounting screws
1. Prepare cabinet opening as shown in Figures 1, 2A, 2B, 2C.
A
B
C
E
D
F
G
I
H
Note: the face of the shelf must
sit 1 3/4" (44.45 mm) back from
the face of the cabinet.
K
L
M
J
N
shelf face
O
cabinet face
A.
B.
C.
D.
E.
F.
G.
6" (152.40 mm)
Suggested electrical outlet location
Anti-Tip block
5" (127 mm)
3-1/2" (88.90 mm)
4" (101.60 mm)
24-3/16" (614.35 mm) minimum
24-1/2" (622.3 mm) maximum
H. 14-13/16" (376.24 mm) to bottom of
Anti-Tip block
I. 1-1/16" (26.97 mm)
J. 23-1/2" (596.90 mm) minimum depth
K. 22-1/8" (561.97 mm)
L. 1-3/4" (44.45 mm)
M. 16-7/8" (428.62 mm) opening
N. Floor must support 100 lb (45.4 kg)
O. 1-3/4" (44.45 mm)
Figure 1
Anti-Tip block
Mounting cleat
Drawer face
B
C
A. 22" (558.8 mm) mounting cleat opening width
B. 1/4" (6.35 mm)
C. 1-1/16" (26.97 mm)
Cabinet
face
A
CL
Top view
Note: the mounting surface of the finished cleat must sit 1 1/16" (26.97 mm) back
from the face of the cabinet [pushing the face of the drawer out 1/4" (6.35 mm)].
Figure 2A
E1
TINSEB 5 41MRR 2
3. Place the drawer adjacent to the wall or cabinet opening. Plug
the power supply cord into the electrical outlet.
No oven
4. Carefully guide the drawer into the prepared opening. Avoid
contact with the sides of the cutout opening and also pinching
the cord between the oven and the wall.
A
Suggested electrical
outlet location
Anti-Tip block
B
5. Slide the drawer all the way back until the mounting flanges
touch the cleats mounted in the cabinet opening.
C
Figure 2B
6. Open the drawer. Using the 4 holes on the drawer as a template,
pre drill the cabinet using a 1/16” (1.57 mm) bit. See Figure 4.
Front view
A. 22-1/8" (561.97 mm) mounting cleat opening width
B. 24-3/16" (614.35 mm) minimum
24-1/2" (622.3 mm) maximum
flush opening width
C. 3/4" (19.05 mm) shelf
Mounting
flange
Move oven location
downward for extended
countertops for better
viewing angle.
16 7/8"
(428.62 mm)
flush opening
height
Front face of cabinet
Figure 2C
Figure 4
Anti-Tip
block
3/4"
(19.05 mm)
shelf
7. Secure the drawer with the 4 screws supplied.
1 3/4" (44.45 mm)
front face of shelf
Side view
2. Install deflector as shown in Figure 3A.
Shelf detail showing the deflector vent during installation.
Position deflector vent and mark holes. Pre drill using a 1/16" (1.57 mm) bit before mounting.
Figure 3A
Shelf detail showing the deflector vent installed.
Figure 3B
E2
30" Flush Mount Deflector Vent: SKMD30F0AS
INSTALLATION INSTRUCTION
Parts includes:
Important notes to the installer
Qty.
• Read all of the Installation Manual that is included with
the Microwave Drawer before installing in the flush mount
configuration.
PREF-B020MRP0
Flush Mount
Deflector Vent
1
• Observe all governing codes, ordinances, and safety
instructions.
Part number
• Be sure to leave these instructions with the consumer.
LX-CZB055MRE0
Mounting screws
2
1. Prepare cabinet opening as shown in Figures 1, 2A, 2B, 2C.
A
B
A.
B.
C.
D.
E.
F.
G.
6" (152.40 mm)
Suggested electrical outlet location
Anti-Tip block
5" (127 mm)
3-1/2" (88.90 mm)
4" (101.60 mm)
30-5/16" (769.92 mm) minimum
30-5/8" (777.87 mm) maximum
H. 14-13/16" (376.24 mm) to bottom of
Anti-Tip block
I. 1-1/16" (26.97 mm)
J. 23-1/2" (596.90 mm) minimum depth
K. 28-7/16" (722.3 mm)
L. 1-3/4" (44.45 mm)
M. 16-7/8" (428.62 mm) opening
N. Floor must support 100 lb (45.4 kg)
O. 1-3/4" (44.45 mm)
C
E
D
G
I
F
H
Note: the face of the shelf must
sit 1 3/4" (44.45 mm) back from
the face of the cabinet.
K
L
J
M
N
shelf face
O
cabinet face
Figure 1
Anti-Tip block
Mounting cleat
A. 28-1/2" (723.9 mm) mounting cleat opening width
B. 1/4" (6.35 mm)
C. 1-1/16" (26.97 mm)
Drawer face
B
C
Cabinet
face
A
CL
Top view
Note: the mounting surface of the finished cleat must sit 1 1/16" (26.97 mm) back
from the face of the cabinet [pushing the face of the drawer out 1/4" (6.35 mm)].
Figure 2A
E3
3. Place the drawer adjacent to the wall or cabinet opening. Plug
the power supply cord into the electrical outlet.
No oven
4. Carefully guide the drawer into the prepared opening. Avoid
contact with the sides of the cutout opening and also pinching
the cord between the oven and the wall.
A
Suggested electrical
outlet location
Anti-Tip block
B
5. Slide the drawer all the way back until the mounting flanges
touch the cleats mounted in the cabinet opening.
C
Figure 2B
6. Open the drawer. Using the 4 holes on the drawer as a template,
pre drill the cabinet using a 1/16” (1.57 mm) bit. See Figure 4.
Front view
A. 28-7/16" (722.3 mm) mounting cleat opening width
B. 30-5/16" (769.92 mm) minimum
30-5/8" (777.87 mm) maximum
flush opening width
C. 3/4" (19.05 mm) shelf
Mounting
flange
Move oven location
downward for extended
countertops for better
viewing angle.
16 7/8"
(428.62 mm)
flush opening
height
Front face of cabinet
Figure 2C
Figure 4
Anti-Tip
block
3/4"
(19.05 mm)
shelf
7. Secure the drawer with the 4 screws supplied.
1 3/4" (44.45 mm)
front face of shelf
Side view
2. Install deflector as shown in Figure 3A.
Shelf detail showing the deflector vent during installation.
Position deflector vent and mark holes. Pre drill using a 1/16" (1.57 mm) bit before mounting.
Figure 3A
Shelf detail showing the deflector shield installed.
Figure 3B
1 Sharp Plaza Suite 1, Mahwah, New Jersey 07495-1123, USA • 1-800-BE-SHARP (237-4277)
335 Britannia Road East, Mississauga, Ontario, L4Z 1W9, Canada
E4
Download PDF

advertising