Fisher Paykel | TK30MOX1 | Installation Instruction | Fisher Paykel TK30CMOX1 Installation Instruction

For replacement parts or if further help is needed concerning this appliance call: Toll
Free 1 888 9 FNP USA (1 888 936 7872) or write to:
Fisher & Paykel Appliances Inc., 5900 Skylab Road, Huntington Beach, CA 92647
or contact us through our web site: www.fisherpaykel.com
Installation Instruction for Microwave Built-In Trim kit



Important Notes to
Consumer & Installer:
Requirements:
Tools:


Before you begin, read these instructions completely.
Microwave trim kit must be installed in compliance with governing codes.
Proper installation is the responsibility of the installer, failure due to improper
installation is not covered under the warranty.
Keep these instructions for future reference.
Be sure to leave these instructions with the customer.

Microwave oven must be installed into cabinetry and properly supported from underneath.

A (6) square inch cut out must be made within the cabinetry for ventilation.

Screwdriver and/or Cordless drill, Phillips or Robertson & Measuring tape
Flush Mount Installation
F
asten the
magnet
mounting
brackets into
the 4 corners of
the cabinet. (1)
P
1
lace
the runners
in the cabinet and
align them with
the front edge of
the shelf. Take
the microwave
and place it on
top of the runners. Center the microwave inside the cabinet
opening. Important: make sure that the microwave feet are
centered on the runners. Mark the position of the runners.
Remove the microwave and secure the runners with the
supplied screws. Plug in the microwave and place it on the
runners. Center the microwave within the opening.
Then, take the
EuroTrim™ and
2
click it onto the
magnet mounts.
Next, open the
microwave door
and check for
proper clearances.
Adjust the
alignment of the
EuroTrim™ by
removing it briefly
and repositioning
the flaps of the
magnet mounts.
Adjust until you are satisfied with the placement. Next, remove
the EuroTrim™ without moving the microwave. (2)
P
eel off the protective coating from the STOPADS©.
Careful: They are very sticky. Gently hook the STOPADS©
behind the front
feet of the
3
microwave.
After initial
contact firmly
press them onto
the runners.
Hint: Lift the
microwave up
at the front and
push it back far
enough to rest
the feet temporarily on the
STOPADS©.
Next, wiggle the handles of the STOPADS© horizontally until
they break off. Then, pull the microwave toward you until the
feet come to a rest inside the STOPADS©. (3)
L
astly, take the EuroTrim™ and click it into position.
If you are
satisfied with
the installation,
remove it one
more time, peel
off the protective
PVC coating from
the EuroTrim™
and click it into
place for its final
mount. (4)
The End
4
Surface Mount Installation
C
reate a cutout
as defined in
the planning guide.
Important: make sure
that the distance
between the shelf
and the bottom edge
of the cutout is as
specified in the
planning guide. (1)
1
of the magnet mount as required to fine-tune the alignment
between the EuroTrim™ and the microwave. Next, open the
microwave door and check for proper clearances. Adjust the
alignment of the EuroTrim™ by removing it briefly and repositioning the flaps of the magnet mount until you are satisfied. (3)
R
lace the runners
in the cabinet and align them with the front edge of
the shelf. Take the microwave and place it on top of the
runners. Center the microwave inside the cabinet opening.
Important: make sure
that the microwave
2
feet are centered on
the runners. Mark the
position of the runners.
Remove the microwave
and secure the runners
with the supplied
screws. (2)
emove the
4
EuroTrim™
without moving
the microwave.
Peel off the
protective PVC
coating from the
STOPADS©
Careful: They are
very sticky. Gently
hook them behind
the front feet of
the microwave. After initial contact firmly press them onto the
runners. Hint: Lift the microwave up at the front and push it
back far enough to rest the feet temporarily on the STOPADS©.
Next, wiggle the handle of the STOPADS© horizontally until
they break off. Then, pull the microwave toward you until the
feet come to a rest inside the STOPADS©. (4)
P
L
P
lug in the microwave and place it
on the runners. Center the microwave within the opening.
Temporarily mount the EuroTrim™ and mark the location of
its outside corners with
a non-permanent
3
marker or pen. Bend
the magnet mounts as
shown and screw them
onto the front of the
panel. Keep about
1/4”-inch (6mm)
distance from the
marked outside corners. Bend the flaps
astly, take the EuroTrim™ and click it into position. If you
are satisfied
5
with the installation, remove it
one more time,
peel off the
protective PVC
coating from the
EuroTrim™ and
click it into place
for its final mount.
(5)
The End
For replacement parts or if further help is needed concerning this appliance call:
Toll Free 1 888 9 FNP USA (1 888 936 7872) or write to:
Fisher & Paykel Appliances Inc., 5900 Skylab Road, Huntington Beach, CA 92647
or contact us through our web site: www.fisherpaykel.com
Download PDF

advertising