Frigidaire | MWTK30SBK | Complete Owner's Guide (English) | Frigidaire MWTK30SBK Complete Owner's Guide (English)

Installation Instructions
Installation
Instructions
BEFORE YOU BEGIN
•
•
Built-in Trim Kit
MWTKP27KF,MWTK27KF,MWTK27KB,MWTK27KW
MWTKP30KF,MWTK30KF,MWTK30KB,MWTK30KW
Read these instructions completely and carefully.
IMPORTANT – Save these instructions
•
for local inspector's use.
•
IMPORTANT – Observe all governing
•
codes and coordinates.
•
•
•
Note to Installer – Be sure to leave
these instructions with the Consumer.
•
Note to Consumer – Keep these
instructions for future reference.
Skill level - Installation of this appliance
requires basic mechanical and electrical
skills
•
Proper installation is the responsibility of the
installer.
Product failure due to improper installation is
not covered under the Warranty.
Unplug the microwave oven before
attempting installation of this kit.
Because the kit includes metal parts, caution
should be used in handling and installation to
avoid the possibility of injury.
Do not remove permanently affixed labels,
warnings, or plates from the product. This
may void the warranty.
IMPORTANT - PLEASE READ
AND FOLLOW
FOR YOUR SAFETY:
WARNING – Before beginning the installation,
switch power off at service panel and lock the
service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to
the service panel.
THIS BUILT-IN KIT IS DESIGNED FOR USE
ONLY WITH ELECTROLUX MICROWAVE
OVENS SPECIFYING BUILT-IN KIT
MWTK(P)27K OR MWTK(P)30K ON THE RATING
LABEL ON THE LEFT SIDE WALL OF THE
MICROWAVE OVEN CAVITY.
QUESTIONS?
For customers in the United States call: 1-800-944-9044
For customers in Canada call: 1-800-265-8352 (English)
1-800-668-4606 ext.8199 (French)
Visit our Website at: www.frigidaire.com
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
PN316495084
SEPT 2009
1
Installation Instructions
PARTS INCLUDED IN THE KIT
1. Front Frame Assembly - QTY 1
2. Exhaust Duct Assembly - QTY 1
3. Screw A - QTY 2
4. Screw B - QTY 4
Screw A
CHOOSING A LOCATION FOR
YOUR MICROWAVE OVEN IF
BUILT-IN
Front Frame Assembly
Built-In Trim Kit allows for the installation of microwaves
listed below to be built into a cabinet or wall by itself or
over an electric wall oven*.
Screw B
Microwave Models:
FGM0205KB
PLMBZ209GC
CGM0205KB
FGM0205KF
GLMB209DS
CGM0205KF
FGM0205KW
GLMB209DB
CGM0205KW
FPM0209KF
CPM0209KF
Exhaust Dust Assembly
See Illustration 1 for proper location when building in
above a wall oven. Carefully follow both the wall oven
installation instructions and Electrolux’s Built-in Kit
instructions. If building over a wall oven, be sure the
clearance between the wall oven and the microwave
oven is a minimum of 3 inches.
*NOTE:
Trim Kit and microwave can only be built-in
over an electric self-clean or non self-clean
single cavity wall oven.
CABINET OR WALL CUTOUT
Cutout Dimensions
Height (A)
Minimum
Maximum
16 3/4” (42.5 cm)
17” (43.2 cm)
Width (B)
Minimum
Maximum
24 3/4” (62.9 cm)
25” (63.5 cm)
Depth (C)
Minimum
20” (50.8 cm)
Illustration 1
2
Installation Instructions
Flanges
Screw A
Exhaust Dust
Assembly
Screw A
Illustration 2
Illustration 3
EXHAUST DUCT ASSEMBLY
ELECTRICAL OUTLET LOCATION
Outlet should NOT be in the shaded area as indicated
on Illustration 2
1. Place the Exhaust Duct in the opening. When
the Exhaust Duct Assembly is in the opening
correctly, the flanges will be tightly against the
lower edge of the opening. See Illustration 3.
NOTE 1:
If the Depth (C) dimension is greater than 21” (53.3 cm),
the outlet location may be in any area on the rear wall.
2.
NOTE 2:
Secure the Exhaust Duct Assembly with the
two screws A.
IMPORTANT: Secure screws in outer hole.
The floor of the opening should be constructed of
plywood strong enough to support the weight of the
oven and floor load (approximately 100 pounds). The
floor should be level for proper operation of the oven. Be
sure to check the local building code as it may require
that the opening be enclosed with side, ceiling and rear
partition. The proper functioning of the oven does not
require the enclosure.
3
Installation Instructions
FRAME INSTALLATION
1.
Place the oven adjacent to the wall or cabinet
opening. Plug the power cord into the electrical
outlet.
2.
Carefully guide the assembled oven into the
prepared opening. Slide the oven on the Exhaust
Duct Assembly. See Illustration 4. Avoid pinching
the cord between the oven and the wall. Adjust
the position of the oven so that the feet of the
oven are fitted into the recesses of the Exhaust
Duct Assembly. See Illustration 5.
3.
Position the FRAME ASSEMBLY to be square
with the oven. Carefully place the FRAME
ASSEMBLY on the oven. Check that it is level and
then secure with two SCREWS B. See Illustration
6.
4.
Foot
Exhaust Dust Assembly
Illustration 5
Secure the bottom portion of the FRAME
ASSEMBLY with the two remaining SCREWS B.
See Illustration 6.
Screw B
Screw B
Screw B
Screw B
Illustration 6
Illustration 4
4
Races
Download PDF

advertising