Amba | ATW-T24 | Hardwired Timer Installation Instructions | Amba ATW-T24 Hardwired Timer Installation Instructions

Amba ATW-T24 Hardwired Timer  Installation Instructions
Single Pole (One location) or 3-Way (Multi-location)
Digital Timer Switch
Cat. No. VPT24-1P, Lighted
LED and CFL Compatible
1800W Incandescent – 15A Fluorescent Ballast – 600W CFL - 5A L.E.D. – 1Hp Motor
120VAC, 60Hz
INSTALLATION INSTRUCTIONS
•
•
•
•
WARNINGS AND CAUTIONS:
TO AVOID FIRE SHOCK OR DEATH; TURN OFF POWER at circuit breaker or fuse when servicing, installing or removing fixture.
To be installed and/or used in accordance with electrical codes and regulations.
If you are unsure about any part of these instructions, consult an electrician.
vizia +™ electronic switches are not compatible with standard 3-way or 4-way switches. They must be used with compatible vizia +™ on/off remotes.
Step 3 Preparing and connecting wires:
Tools needed to install your Timer Switch
Pull off pre-cut insulation from timer leads. Make sure that
the ends of the wires from the wall box are straight (cut if
necessary). Remove insulation from each wire in the wall
box as shown.
Slotted/Phillips Screwdriver
Electrical Tape
Pliers
PencilCuttersRuler
•
•
•
•
Step 4b 3-Way Wiring with Coordinating Remote Switch, Step 4c 3-Way Wiring with Matching Remote Switch,
VP0SR-10, (no LED) Application:
VP0SR-1L, (w/LED) Application:
Coordinating Remote Switch
Your device may include color options. To change color of the face,
proceed as follows:
Th
5/8"
(1.6 cm)
Strip Gage
(measure bare
wire here)
BK
Th
12 AM
12 AM
MENU
MENU
SET
SET
Line up tabs and
press in sides one at
a time to attach
Push in side
at tab to release
For non-standard wiring applications, refer
to Wire Nut and Conductor Size Chart
WIRE NUT / # OF CONDUCTOR
COMBINATION CHART
Installing your Timer Switch
NOTE: Use check boxes
when Steps are completed.
OFF POWER at circuit breaker or fuse and test that power is
off before wiring!
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Load
Step 4a Single Pole Wiring Application:
Black
NOTE: If the wiring in your wall box does not resemble any of
these configurations, consult a qualified electrician.
White
2
1
2
3
4
Single Pole
1. Line (Hot)
2. Neutral
3. Ground
4. Load
Yellow/Red
Insulating label:
This wire is used in 3-way installations only.
For single pole installations, do not remove insulating label.
Timer Switch
3-Way
1. Line or Load
(see important instruction below)
2. Neutral
3. Ground
4. First Traveler – note color
5. Second Traveler – note color.
NOTE: For matching remote
w/LEDs installation, the First
Traveler becomes Line Hot.
IMPORTANT : For 3-Way applications, note that one of the screw
terminals from the old switch being removed will usually be a different
color (Black) or labeled Common. Tag that wire with electrical tape and
identify as the common (Line or Load) in both the switch wall box and
remote wall box.
2
3
Green
3
4
5
1
4
Red
1
WH
BK
YL/RD
Black
Load
White
RD
Green
Ground
Hot (Black)
Line
120VAC, 60Hz
Use lead for 3-Way or more
applications only. For single
pole applications, do not
remove the insulating label.
Neutral (White)
WIRING TIMER SWITCH:
Connect wires per WIRING DIAGRAM as follows:
•
•
•
•
•
5
Red
3
YL/RD
4
Red
RD
5
3
Timer Switch
Matching Remote Switch (w/LED)
• Ensure that the word “TOP” is
facing up on device strap.
1
2
• Partially screw in mounting
screws in wall box mounting
holes.
5
4
Green
Green
Coordinating Remote Switch (no LED)
Black
• Make sure that the ends of the wires from the wall box are
straight (cut if necessary).
• Remove insulation from each wire in the wall box as shown.
• For Single-Pole Application, go to Step 4a.
• For 3-Way Coordinating Remote (no LEDs) Application, go to Step 4b.
• For 3-Way Matching Remote (with LEDs) Application, go to Step 4c.
Step 2 Identifying your wiring application (most common):
5
Terminal
Screw marked
Yellow/Red
(YL/RD)
White
Yellow/
Red
4
3
Timer Switch
Hot (Black)
1- #12 w/ 1 to 3 #14, #16 or #18
2- #12 w/ 1 or 2 #16 or #18
1- #14 w/ 1 to 4 #16 or #18
2- #14 w/ 1 to 3 #16 or #18
Step 1 WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN
RD
4
2
1
2
Yellow/
Red
2
WH
Step 5 Testing your Switch prior to mounting in
wall box:
• Position all wires to provide
room in outlet wall box for
device.
Black
BK
1
White
1
YL/RD
Timer Switch
Black
3
Cut
(if necessary)
A
Matching Remote Switch
Additonal Neutral Wire
WH
12 PM
A
Timer Switch
Terminal
Screw marked
White (WH)
Changing the color of your device:
12 PM
Recommended minimum wall box depth is 2-1/2".
Use only one (1) vizia +TM digital timer switch in a multi-location circuit with up to 9 coordinating remote switches (without LEDs) or up to 4 matching remote switches (with LEDs).
Maximum wire length from digital timer switch to all installed remotes cannot exceed 300 ft (90 m).
Use this device with copper or copper clad wire only.
Green or bare copper wire in wall box to timer switch Green lead.
Line Hot wall box wire to timer switch Black lead.
Load wall box wire to timer switch Red lead.
Line Neutral wall box wire to timer switch White lead.
NOTE: If label is missing place electrical tape around the timer switch
Yellow/Red lead. Ensure no strands are exposed.
• Proceed to Step 5.
White
WH
BK
(unused)
WH
RD
YL/RD
Hot (Black)
YL/RD
Green
Ground
(unused)
BK
Line
120VAC, 60Hz
RD
WH
BK
WH
Green
Ground
Line
120VAC, 60Hz
YL/RD
NOTE: Dress wires with a bend as shown
in diagram in order to relieve stress when
mounting device.
BK
Green
Ground
RD
YL/RD
Green
Ground
Neutral (White)
WIRING TIMER SWITCH:
Connect wires per WIRING DIAGRAM as follows:
NOTE: The timer switch must be installed in a wall box that has a Line Hot
connection.
NOTE: Maximum wire length from timer switch to all installed remotes
cannot exceed 300 ft (90 m).
• Green or bare copper wire in wall box to timer switch Green lead.
• Line Hot (common) wall box wire identified (tagged) when removing old
switch to timer switch Black lead.
• First Traveler wall box wire to timer switch Red lead
(note wire color).
• Remove Red insulating label from timer switch Yellow/Red lead.
• Second Traveler wall box wire to the Yellow/Red lead (note wire
color). This traveler from the timer switch must go to the terminal screw
on the remote marked "YL/RD".
• Line Neutral wall box wire to timer switch White lead.
WIRING COORDINATING REMOTE SWITCH (VP0SR-10):
Connect wires per WIRING DIAGRAM as follows:
NOTE: "BK" and "RD" terminals on coordinating remote switch are
unused. Tighten both screws.
NOTE: Maximum wire length from timer switch to last remote cannot
exceed 300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch to First
Traveler (note color as above).
• Second Traveler wall box wire (note color as above) to terminal screw
marked "YL/RD". This traveler from the remote must go to the Yellow/
Red lead on the timer switch.
• Remove White insulating label from terminal screw marked "WH".
• Line Neutral wall box wire to terminal screw marked "WH".
• Proceed to Step 5.
Black
Load
White
Neutral (White)
NOTE: The timer switch must be installed in a wall box that has a Load
connection. The matching remote must be installed in a wall box with
a Line Hot connection and a Neutral connection. A Neutral wire to the
matching remote needs to be added as shown.
If you are unsure about any part of these instructions, consult an
electrician.
NOTE: Maximum wire length from dimmer to all installed remotes cannot
exceed 300 ft (90 m).
WIRING MATCHING REMOTE SWITCH, VP0SR-1L
(wall box with Line Hot connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing
old switch and First Traveler to remote terminal screw marked "BK".
• Second Traveler wall box wire from switch to remote terminal screw
marked "YL/RD" (note wire color). This traveler from the remote must
go to the Yellow/Red lead on the timer switch.
• Line Neutral wall box wire to remote terminal screw marked "WH".
WIRING TIMER SWITCH (wall box with Load connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to timer switch Green lead.
• Load wall box wire identified (tagged) when removing old switch to timer
switch Red lead.
• First Traveler Line Hot to timer switch Black lead.
• Remove Red insulating label from Yellow/Red lead.
• Second Traveler wall box wire (note color as above) to timer switch
Yellow/Red lead. This traveler from the switch must go to the terminal
screw on the remote marked "YL/RD".
• Line Neutral wall box wire to timer switch White lead.
• Proceed to Step 5.
• Restore power at circuit
breaker or fuse.
• Wait until
or time is
displayed on the screen.
• Press pad until locator light is
OFF. Load should turn ON.
If loads do not turn ON, refer
to the TROUBLESHOOTING
section.
Step 6
Locator LED
Switch Mounting:
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.
• Installation may now be completed
by tightening mounting screws into
wall box. Attach wallplate.
Step 7 Restore Power:
Restore power at circuit breaker or fuse.
Installation is complete.
WEB VERSION
WARNINGS AND CAUTIONS:
DI-000-VPT24-02F
NOTE: The Digital Timer Switch is equipped with an internal
rechargeable battery back-up to keep programmed settings
in the event of a power interruption.
b) Press and hold SET followed by
(Override) until
stops flashing and
flashes (approximately 5 seconds).
Press SET to confirm device Reset.
ICON DEFINITIONS
Permanent override OFF (schedule at a glance not available)
Temporary override OFF (when flashing)
Permanent override ON (schedule at a glance not available)
Temporary override ON (when flashing)
Sun down
Timer Mode
12 PM
Event number
Days of the week
Offset of
astronomic clock
Day time
Daylight
Savings Time
DST
Event
A
P
MTWThFSaSu
Offset
12
Battery power
(No AC power)
AM
Sun up
Delete
Setting Timed
Events
Longitude/
Latitude
degrees
AM or PM
Timer schedule
at a glance
Night time
Programming Menus
will begin
c) Product will go through a brief self test and then
to flash. Choose
or
by using
or
until the
selected mode appears and pressing SET to confirm your choice.
•Use
or
to choose your latitude (N) and press
confirm your choice.
•Use
or
to choose your longitude (W) and press
confirm your choice.
d) Continue to the programming section for the Mode chosen.
•
will be flashing to represent the offset time. Choose the
amount of time, if any, to turn the load ON/OFF before or after
Sunup and Sundown by pressing
to add time to the Sunup/
Sundown time and use
to subtract time from the Sunup/
Sundown time. Press SET to confirm your choice (up to 3 hours
and 59 minutes).
PROGRAMMING PRO MODE
1. Setting up the Time, Daylight Savings Time Option and the Date:
a)
will be flashing. Press
or
press SET to confirm your choice.
to select the hour and
b)
will be flashing. Press
or
press SET to confirm your choice.
to select the minutes and
A
A
c)A or P will be flashing. Press
or
to select A for AM or
P for PM and press SET to confirm your choice.
d)
will be flashing. Set the daylight savings time mode to OFF
or AUTO (for automatic adjustment of daylight savings time)
by using
or
to choose daylight savings time option and
press SET to confirm your choice.
NOTE: Daylight Savings Time shall start at 2am on the second
Sunday of March (add one hour) and end at 2am on the first Sunday
of November (subtract one hour).
DST
Pro mode
Pro Mode provides up to 50 ON/OFF events for any day or
combination of days, M-Su, M-F, or Sa-Su at desired fixed times or
self adjusting Sunup and Sundown times. In this mode self adjusting
Daylight Savings Time and random modes are also available.
Std Mode provides up to 3 ON/OFF events for M-Su, M-F, or Sa-Su
at desired fixed times only. Self adjusting Sunup and Sundown and
Daylight Savings Time are NOT available in Standard Mode.
To exit programming at any time press override button To program your device:
a) Perform a System Reset by gently lifting the VPT24 door from the
bottom of the push pad until an audible click is heard. The door will
stay open while you are programming the device:
•Press MENU until PRG is in the lower left corner. Press
enter the programming mode.
A
Th
MENU
SET
Override button
SET
to
•
Event 1 will be flashing. Press SET to choose this event or use
to move to the next event and press SET to confirm your
event number choice.
12 PM
Event
SET
will be flashing. Use
or
to confirm your choice.
f) will be flashing. Use
or
press SET to confirm your choice
to choose the year and
to choose the month and
g)
will be flashing. Use
or
to choose the date
and press SET to confirm your choice. The day of week will
automatically adjust.
•All days of the week will be flashing. Press SET to choose all
days of the week or use
or
to scroll through M-F, SaSu, any single day or combination of days. NOTE: To choose a
combination of days press SET after each day you want and then
move on to the next day by pressing
or
. Continue to
scroll using
until PRG flashes.
12 PM
Event
2. Programming your Timer Options:
MTWThFSaSu
a) Setting Sunup, Sundown, desired Offset Time and Time Zone:
Sunup and Sundown are automatically adjusted using the
latitude and longitude coordinates of your location. To obtain these
coordinates go to www.leviton.com/VPT24 and click on Longitude/
Latitude Coordinates Lookup... Type in your home address and
press enter. Your latitude (N) and longitude (W) coordinates will
be shown on the screen. Write down only the 2 or 3 digit number.
Disregard a negative symbol (–) if it preceeds the number.
TIME ZONE CALCULATIONS
12 AM
to
b) Setting ON/OFF Events:
12
Longitude
Time Zone
60° – 80°
Eastern
81° – 95°
Eastern, Central
96° – 110°
Central, Mountain
111° – 135°
Mountain, Pacific, Alaskan
136°-143°
Pacific, Alaskan, Hawaii-Aleutian
144°+
Alaskan, Hawaii-Aleutian
AM
•When done choosing the desired days PRG in the lower left
corner will flash. Press SET to confirm the chosen days and
continue on to choosing the event TURN ON TIME.
12 PM
USE IN MULIT-LOCATION APPLICATIONS
A
SET
will be flashing. Use
to confirm your choice.
or
• The minutes will be flashing. Use
Press SET to confirm your choice.
to choose the hours. Press
or
to choose the minutes.
• A for AM or P for PM will be flashing. Use
A or P. Press SET to confirm your choice.
• The day of the week will be flashing. Use
day. Press SET to confirm your choice.
or
or
to choose the
to choose the
To set ON/OFF Events:
• Press MENU until PRG is in the lower left corner. Press
programming mode.
SET
to enter the
• Event 1 will be flashing. Press SET to choose this event or use
to move to the next event and press SET to confirm your event
number choice.
• All days of the week will be flashing. Press SET to choose all days of
the week or use
or
to scroll through M-F and Sa-Su. Press
SET
to confirm your days of the week choice and continue to program
the event ON TIME.
• At
use
or
to choose
delete an existing program and press
SET
for time, or
to
to confirm your choice.
• Use
or
to choose the hour and press SET to confirm your
choice. Do the same for minutes and press SET to confirm your
choice. Continue to program the event OFF TIME.
• At 6:00P press SET to choose the OFF TIME or use
choose
to delete an existing program and press
your choice.
SET
or
to
to confirm
• Continue to set desired events in the same manner. When you are
done press
to escape out of programming. If no buttons are
pressed after approximately 30 seconds the device will automatically
exit out of programming mode.
TIMER OVERRIDES
• Activate Temporary Override by pressing the push pad to toggle the
load (ON to OFF or OFF to ON).
• Activate Permanent Override by pressing and holding the push pad
for several seconds to maintain the load in the current state (either ON
or OFF).
CHANGING SETTINGS
• Press MENU until CLK appears at the bottom of the screen
SET
to enter this mode. Adjust the clock using
or
pressing SET after each setting.
. Press
and
Event
12 AM
•At
use
or
to choose
for time,
for
Sundown,
for Sunup or
to delete an existing
program and press SET to confirm your choice.
•If
press
is chosen, use
or
to choose the hour and
SET to confirm your choice. Do the same for minutes.
•
At 6:00P press SET to choose a TURN OFF TIME or use
for Sunup
or
to choose
for Sundown,
or
to delete an existing program and press SET to confirm
your choice.
•If
press
is chosen, use
or
to choose the hour and
SET to confirm your choice. Do the same for minutes.
•Continue to set desired events in the same manner. When this
is done press
to escape out of programming. If no buttons
are pressed after approximately 30 seconds the device will
automatically exit out of programming mode.
This function will add or subtract anywhere from 1 to 20 minutes to each
selected ON and OFF time to create a random pattern.
• Press MENU until RND appears at the bottom of the screen and press
SET
to enter this mode.
• Use
SET
or
to toggle between
to confirm your choice.
and
When using a remote switch(es) with your vizia +TM 24 hour timer
you will be able to activate the temporary override or the permanent
override from the remote switch. To activate or deactivate the
temporary override press the push pad on the remote switch. To
activate permanent override press and hold the remote switch push
pad. Either of these actions will toggle the state of the load.
TROUBLESHOOTING
•Lights flickering or intermittent power to load
- Load has a bad connection.
- Wires not secured firmly with wire connectors of timer switch or
terminal screws of remote.
• Load does not turn ON and Locator LED does not turn ON
- Circuit breaker or fuse has tripped.
- Load is burned out.
- Load Neutral connection is not wired.
• Remote does not operate lights
- Ensure that total wire length does not exceed 300 ft (90 m).
For additional information, contact Leviton’s
Techline at 1-800-824-3005 or visit Leviton’s
website at www.leviton.com
This product is covered by U.S. Patent No. D634,276 and
corresponding foreign patents.
• Degree of protection provided: IPX0
• Type of Action: 1CS
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is
subject to following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation of
the device.
This equipment has been tested and found to comply with the limits
for a Class B Digital Device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment OFF and
ON, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving Antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/tv technician for help.
FCC CAUTION
Turning Random Mode ON/OFF (Pro Mode ONLY):
The time zones are limited to the North American Continent. The options
you are presented are determined via your longitude in the chart below:
12 PM
SET
PROGRAMMING STANDARD MODE
To set the clock:
•
12 AM
e)
press
or Standard mode
to
SET
•
will appear. The time zone closest to the coordinates you
entered will flash. Press SET if this is correct. If this is not correct
use
or
to choose your time zone and press SET to
confirm your choice.
DST
Backlit LCD display will light up when any button is pressed and will
extinguish 30 seconds after the last button press.
Decide which mode is best for your application:
•On your timer press MENU until SUN appears at the bottom of the
screen and press SET to confirm your choice.
Timer Schedule at a Glance will allow you to quickly see your timers
ON/OFF settings for the day. The displayed segments represent the
time(s) your load will be on. The segment representing the current time
will be flashing.
PROGRAMMING GUIDE
and press
DELETE ALL EVENTS
WEB VERSION
OPERATION
Any changes or modifications not expressly approved by Leviton
Manufacturing Co., Inc., could void the user's authority to operate the
equipment.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada
should contact Leviton in writing at Leviton Manufacturing of Canada
Ltd to the attention of the Quality Assurance Department, 165
Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by
telephone at 1 800 405-5320.
lf at any time you want to delete all of your programmed events, you can
perform a DELETE ALL EVENTS function:
a) Gently lift the VPT24 door from the bottom of the push pad until an
audible click is heard.
b) Press and hold SET followed by
(Override) until
stops
flashing. Upon releasing both buttons all events will be deleted and
the Timer Schedule at a Glance will appear with only the current time
segment flashing.
© 2013 Leviton Mfg. Co., Inc.
DI-000-VPT24-02F
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with
proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened,
abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for
a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising