Hotpoint CIO632CC S Instruction for Use

Operating Instructions
HOB
GB
GB
English,1
Contents
Warnings, 2
Installation, 3-4
Positioning
Electrical connection
Description of the appliance, 5
Control panel
Start-up and use, 6-10
Precautions and tips, 11
General safety
Disposal
Care and maintenance, 12
Switching the appliance off
Cleaning the appliance
Disassembling the hob
ea
08 se
to 44 ph
a 8 o
gu ctiv 24 ne
ar ate 24 us
an y 2 o
te ou 4 n
e r
Technical description of the models, 12
Pl
CIO 632 CC S
Switching on the hob
Switching on the cooking zones
Booster function
Switching off the cooking zones
Programming the cooking duration
Timer
Control panel lock
Switching off the hob
“Demo” mode
FLEXI ONE mode
Practical advice on using the appliance
Safety devices
Practical cooking advice
WARNING
• WARNING: The appliance and
its accessible parts become hot
during use.
• Care should be taken to avoid
touching heating elements.
• Children less than 8 years of
age shall be kept away unless
continuously supervised.
• This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved. Children shall not
play with the appliance. Cleaning
and user maintenance shall not
be made by children without
supervision.
• WARNING: Unattended cooking
on a hob with fat or oil can be
dangerous and may result in fire.
• NEVER try to extinguish a fire with
water, but switch off the appliance
and then cover flame e.g. with a lid
or a fire blanket.
• WARNING: Danger of fire: do
not store items on the cooking
surfaces.
• WARNING: If the surface in glassceramic is cracked, switch off the
appliance to avoid the possibility of
electric shock.
•Never use steam cleaners
or pressure cleaners on the
appliance.
•The appliance is not intended to be
operated by means of an external
timer or separate remote control
system.
•Do not place metal objects (knives,
spoons, pan lids, etc.) on the hob as
they may become hot.
•After use, switch off the hob element
by its control and do not rely on the
pan detector.
GB
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
2
Installation
GB
5 mm
! Before operating your new appliance please read
this instruction booklet carefully. It contains important
information concerning the safe operation, installation
and maintenance of the appliance.
! Please keep these operating instructions for future
reference. Pass them on to any new owners of the
appliance.
min. 20 mm
COMPARTMENT
Positioning
min. 40 mm
! Keep all packaging material out of the reach of
FAN-ASSISTED
OVEN
min. 40 mm
SUPPORTING
SURFACE
30
FRONT SIDE
OF HOB
40
Built-in appliance
Use a suitable cabinet to ensure that the appliance
functions properly.
• The supporting surface must be heat-resistant up to
a temperature of approximately 100°C.
• If the appliance is to be installed above an oven,
the oven must be equipped with a forced ventilation
cooling system.
• Avoid installing the hob above a dishwasher: if this
cannot be avoided, place a waterproof separation
device between the two appliances.
• Depending on the hob you want to install, the cabinet
must have the following dimensions (see figure):
min. 20 mm
5 mm
children. It may present a choking or suffocation hazard
(see Precautions and tips).
! The appliance must be installed by a qualified
professional in accordance with the instructions
provided. Incorrect installation may cause harm to
people and animals or may damage property.
UNDERSIDE
OF HOB
48
590
0
52
/-
0+
56
0+
/- 1
1
49
Ventilation
To allow adequate ventilation and to avoid overheating of
the surrounding surfaces the hob should be positioned as
follows:
• At a minimum distance of 40 mm from the back
panel.
• So that a minimum distance of 20 mm is maintained
between the installation cavity and the cabinet
underneath.
• Kitchen cabinets adjacent to the appliance and taller
than the top of the hob must be at least 600 mm from
the edge of the hob.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
3
Fixing
GB
The appliance must be installed on a perfectly level
supporting surface.
Any deformities caused by improper fixing could affect the
features and operation of the hob.
The thickness of the supporting surface should be taken
into account when choosing the length of the screws for the
fixing hooks:
• 30 mm thick: 23 mm screws
• 40 mm thick: 13 mm screws
Fix the hob as follows:
1. Use short flat-bottomed screws to fix the 4 alignment
springs in the holes provided at the central point of each side
of the hob.
2. Place the hob in the cavity, make sure it is in a central
position and push down on the whole perimeter until the hob
is stuck to the supporting surface.
3. For hobs with raised sides: After inserting the hob into its
cavity, insert the 4 fixing hooks (each has its own pin) into
the lower edges of the hob, using the long pointed screws
to fix them in place, until the glass is stuck to the supporting
surface.
! The screws for the alignment springs must remain
accessible.
! In order to adhere to safety standards, the appliance
must not come into contact with electrical parts once it
has been installed.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a tool.
Electrical connection
! The electrical connection for the hob and for any built-in
oven must be carried out separately, both for safety purposes
and to make extracting the oven easier.
Single-phase connection
The hob is equipped with a pre-connected electricity
supply cable, which is designed for single-phase
connection. Connect the wires in accordance with the
instructions given in the following table and diagrams:
Voltage and
mains frequency
Electrical cable
220-240V 1+N ~
50 Hz
Wire connection
: yellow/green
N: the two blue wires together
L: brown and black together
Other types of connection
If the mains supply corresponds with one of the following:
Voltage and mains frequency
• 400V - 2+N ~ 50 Hz
• 220-240V 3 ~ 50 Hz
• 400V - 2+2N ~ 50 Hz
• 400V 3 - N ~ 50 Hz
Separate the wires and connect them in accordance
with the instructions given in the following table and
diagrams:
Voltage and
mains frequency
400V - 2+N ~
50 Hz
220-240V 3 ~
50 Hz
400V 3-N ~
50 Hz
Electrical cable
Wire connection
: yellow/green;
N: the two blue wires
together
L1: black
L2: brown
: yellow/green;
400V - 2+2N ~
50 Hz
N1: blue
N2: blue
L1: black
L2: brown
Connecting the electricity supply cable to the mains
If the appliance is being connected directly to the
electricity mains an omnipolar switch must be installed
with a minimum opening of 3 mm between contacts.
! The installer must ensure that the correct electrical
connection has been made and that it is fully compliant
with safety regulations.
Before connecting the appliance to the power supply, make
sure that:
• The appliance is earthed and the plug is compliant with
the law.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located on
the appliance itself.
• The voltage falls within the range of values indicated on
the data plate.
• The socket is compatible with the plug of the appliance.
If the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.
! Once the appliance has been installed, the power
supply cable and the electrical socket must be easily
accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only.
! The manufacturer declines any liability should these
safety measures not be observed.
! Do not remove or replace the power supply cable
for any reason. Its removal or replacement will void
the warranty and the CE marking. INDESIT does not
assume liability for accidents or damage arising from
replacement/removal of the original power supply cable.
Replacement can only be accepted when carried out by
personnel authorised by INDESIT and using an original
spare part.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
4
Description of the
appliance
Control panel
GB
The control panel described in this manual is only a representative example: it may not exactly match the panel on
your appliance.
TIMER
indicator light
REDUCE TIME
button
FLEXI ZONE
indicator light
POWER and
RESIDUAL HEAT
indicators
Max
Max
COOKING ZONE PROGRAMMED
indicator light
BOOSTER
button
ON/OFF
button
BOOSTER
indicator light
FLEXI ZONE MAX
button
button
Booster
PROGRAMME TIMER
display
ON/OFF
indicator light
Booster
CONTROLS LOCKED
indicator light
REDUCE POWER
button
COOKING ZONE
SELECTED indicator light
PROGRAMME
TIMER button
CONTROL PANEL
LOCK button
INCREASE
TIME button
INCREASE
POWER button
• INCREASE TIME button increases the time value set
on the timer (see Start-up and use).
• DECREASE TIME button decreases the time value
set on the timer (see Start-up and use).
• INCREASE POWER button switches on the hotplate
and controls the power (see Start-up and use).
• REDUCE POWER button controls the power and
switches off the hotplate (see Start-up and use).
• COOKING ZONE SELECTED indicator shows a
particular cooking zone has been selected and
therefore various adjustments are possible.
• POWER indicator provides a visual display for the
current heat level.
• ON/OFF button switches the appliance on and off.
• ON/OFF indicator light shows whether the appliance
is on or off.
• PROGRAMME TIMER* button controls the cooking
programme times (see Start-up and use).
• PROGRAMME TIMER* display shows which
programme has been selected (see Start-up and
use).
• COOKING ZONE PROGRAMMED* indicator lights
show which cooking zones are being used during a
cooking programme (see Start-up and use).
• CONTROL PANEL LOCK button prevents accidental
changes to the hob settings (see Start-up and use).
• CONTROL PANEL LOCK indicator light shows the
control panel has been locked (see Start-up and use).
• BOOSTER button* activates the booster function 3000 W - of the cooking zone (see Start-up and use).
• BOOSTER indicator light* shows that the booster
function has been activated.
• TIMER* indicator light shows that the timer has been
activated
• FLEXI ZONE button - activates the FLEXI ZONE
mode
• FLEXI ZONE indicator light shows FLEXI ZONE
function has been activated
• MAX button- allows for an immediate activation of
the cookinfg zone on the maximum power level: 9
! This product complies with the requirements of the
latest European Directive on the limitation of power
consumption of the standby mode.
If no operations are carried out for a period of 2
minutes, after the residual heat indicator lights turn
off and the fan stops (if present), the appliance
automatically switches to the “off mode”.
The appliance resumes the operating mode once the
ON/OFF button is pressed.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
5
Start-up and use
GB
! The glue applied on the gaskets leaves traces of
grease on the glass. Before using the appliance, we
recommend you remove these with a special nonabrasive cleaning product. During the first few hours of
use there may be a smell of rubber which will disappear
very quickly.
Switching on the cooking zones
! A few seconds after the hob is connected to the electricity
button.
double and
• To begin operating a cooking zone, press the
corresponding control button and set the desired
supply, a buzzer will sound. The hob may now be switched
on.
Types of noise during normal hob operation:
• Buzz: due to the vibration of the metallic parts that
make up the induction element and the pot; it is
generated by the electromagnetic field required for
heating and increases as the power of the induction
element increases.
• Soft whistle: heard when the pot placed on the
heating zone is empty; the noise disappears once
food or water is placed into the pot.
• Crackle: produced by the vibration of materials on
the bottom of the pot due to the flow of parasitic
currents caused by electromagnetic fields
(induction); can be more or less intense depending
on the material making up the bottom of the pot, and
decreases as the pot dimensions increase.
• Loud whistle: heard when two induction elements of
the same group function simultaneously at maximum
power and/or when the booster function is set on
the larger element while the other is auto-adjusted.
Noise is reduced by decreasing the power level of
the auto-adjusted induction element; pot bottom
layers made of different kinds of materials are among
the main causes of this noise.
• Fan noise: a fan is necessary to ensure the hob
functions correctly and to safeguard the electronic
unit from possible overheating. The fan functions at
maximum power when the large induction element is
at maximum power or when the booster function is on;
in all other cases, it works at average power depending
on the temperature detected. Furthermore, the fan may
continue to work even after switching the hob off, if the
temperature detected is high.
The types of noise listed above are due to induction
technology and are not necessarily operational faults.
- +
! If the or
button is pressed for an extended
period of time, the display scrolls quickly though the
power levels and timer minutes.
Switching on the hob
To switch the hob on, press and hold the
approximately one second.
button for
Each cooking zone is controlled using a selector button
and a power adjustment device consisting of a
- +
power level (between 0 and 9) using the buttons
and
-
+
.
Booster function*
The booster function for some of the cooking zones may
be used to shorten heating-up times. It may be activated
Booster
button. The indicator light directly
by pressing the
above the button will illuminate. This function boosts the
power to 2000 W or 3000 W, depending on the size of
the relevant cooking zone.
The booster stops automatically after 4 minutes. While
the booster for one of the cooking zones is active, the
corresponding front or rear cooking zone will operate
at a reduced power level (e.g. if the booster for the rear
left-hand hotplate has been activated, the power level of
the front left-hand hotplate will be reduced). For further
information, please refer to the Technical description of
the models.
Switching off the cooking zones
To switch off a cooking zone, select it using the
corresponding selector button
and:
-
• Press the button: the power of the cooking zone
will progressively decrease until it is switched off.
Programming the cooking duration
! All the cooking zones may be programmed
simultaneously, for a duration between 1 and 99
minutes.
1. Select the cooking zone using the corresponding
selector button.
2. Adjust the power level of the cooking zone.
programming button. The indicator
3. Press the
light corresponding to the selected zone will start
flashing.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
6
4. Set the cooking duration using the
buttons.
- +
and
Control panel lock
5. Confirm by pressing the
button or automatic
selection occurs after 10 seconds.
The timer begins counting down immediately.
A buzzer sounds for approximately 1 minute and the
cooking zone switches off when the set programme has
finished.
Repeat the above procedure for each hotplate you wish
to programme.
Using multiple programmes and the display
If one or more hotplates are programmed, the display
will show the data for the hotplate with the least time
remaining, and the light corresponding to the position of
the hotplate will flash. The lights corresponding to the
other hotplates programmed will be switched on.
To visualise the time remaining for the other
button
programmed hotplates, press the
repeatedly: the time remaining for each hotplate will be
shown sequentially in a clockwise order, starting from
the front left hotplate.
Changing the programme
button repeatedly until the duration
1. Press the
you wish to change is shown.
2. Use the
button.
To cancel a programme, follow the above instructions.
-
At step 2, press the button: the duration decreases
progressively until it reaches 0 and switches off. The
programme resets and the display exits programming
mode.
Timer
The hob must be switched on.
The timer can be used to set a duration up to 99
minutes.
1. Press the
programming button until the timer
indicator light is illuminated
.
2. Set the desired duration using the
- +
and
button to lock the control panel:
etc.). Press the
the indicator light above the button will switch on.
To use any of the controls (e.g. to stop cooking), you
button for a
must switch off this function. Press the
few moments, the indicator light will switch off and the
lock function will be removed.
Switching off the hob
Press the button
to switch off the appliance - do not
rely solely on the pan sensor.
If the control panel lock has been activated, the controls
will continue to be locked even after the hob is switched
on again. In order to switch the hob on again, you must
first remove the lock function.
“Demo” mode
It is possible to set the hob to a demonstration mode
where all the controls work normally but the heating
elements do not switch on. To activate the “demo” mode
the hob must be switched on, with all the hotplates
switched off.
+ -
and buttons simultaneously
• Press and hold the
for 6 seconds. When the 6 seconds have elapsed,
the ON/OFF and CONTROLS LOCKED indicator
buttons to set the new duration.
3. Confirm by pressing the
GB
When the hob is switched on, it is possible to lock the
oven controls in order to avoid accidental changes
being made to the settings (by children, during cleaning,
buttons.
3. Confirm by pressing the
button.
The timer begins counting down immediately. When the
time has elapsed, a buzzer will sound (for one minute).
lights will flash for one second. Release the
+
and
-
buttons and press the
button;
• The display will show the text DE and MO and the
hob will be switched off.
• When the hob is switched on again it will be set to
the “demo” mode.
To exit this mode, follow the procedure described
above. The display will show the text DE and OF and
the hob will be switched off. When it is next switched
on, the hob will function normally.
Practical advice on using the appliance
! Use cookware made from materials which are
compatible with the induction principle (ferromagnetic
material). We especially recommend pans made from:
cast iron, coated steel or special stainless steel adapted
for induction. Use a magnet to test the compatibility of
the cookware.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
7
GB
The FlexiZONE mode
The FLEXI Zone can be used to set the power of two
„interconnected” hotplates to the same level. It can be
activated if the two hotplates are OFF, by pressing the
FLEXI ZONE button
The FLEXI ZONE can be activated while the hob is on
by pressing the FLEXI ZONE button once; the LEDs
corresponding to both linked hotplates light up.
The 2 LEDs remain lit as long as the hotplates are
linked (if FLEXI ZONE button is pressed again, the
hotplates are disconnected and are both set to power
level 0).
Pressing the +, - or Max buttons for one of the two Flexi
hotplates also affects the display corresponding to the
other hotplate.
To deactivate the FLEXI ZONE, press the button .
A timer may be set for the FLEXI zone; this appears on
the display and both LEDs corresponding to the linked
hotplates light up. When the Timer button is pressed,
the two linked hotplates are treated as if they were a
single zone.
Selecting and using FLEXI ZONE
To begin using the FLEXI ZONE, press the
To set the power level (see above).
button.
FLEXI ZONE operation
Once you have selected FLEXI ZONE by pressing
the button , the 2 LEDs corresponding to the FLEXI
ZONE for both hotplates light up; it will then be possible
to control both as if they were a single zone. The power
level will appear on both displays. If only the upper or
lower part is in use, the display corresponding to the
unused zone will begin to flash, and after 3 minutes
cooking will automatically revert to standard mode (not
FLEXI).
! Once activated, the FLEXI ZONE can also be
programmed, using the same procedure as described
for the individual hotplates.
! Accessories
For optimal FLEXI ZONE performance, we recommend
the use of pans with an elliptical or elongated base and
a major diameter of at least 250 mm; if using pans with
a smaller diameter, we recommend positioning them in
the upper or lower part as indicated by the X symbol.
If the saucepan is not in the centre of the screen
printing detail, you may hear a whistling sound or
a slight buzzing noise; this does not indicate a hob
malfunction. We recommend adjusting the position of
the pan so that it is in the centre of the FLEXI ZONE.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
8
SUITABLE
*
UNSUITABLE
Cast iron
Enamelled steel
Special stainless steel
Copper,
Aluminium, Glass, Earthenware,
Ceramic, non magnetic Stainless steel
In addition, to obtain the best results from your hob:
• Use pans with a thick, flat base in order to fully utilise
the cooking zone.
Safety switch
GB
The appliance has a safety switch which automatically
switches the cooking zones off after they have been in
operation for a certain amount of time at a particular
power level. When the safety switch has been triggered,
the display shows “0”.
For example: the right rear hotplate is set to 5 and will
switch off after 5 hours of continuous operation, while
the front left hotplate is set to 2 and will switch off after
8 hours.
Power level
Maximum operating time in hours
1
9
2
8
3
7
4
6
5
5
6
4
7
3
8
2
9
1
• Always use pans with a diameter which is large
enough to cover the hotplate fully, in order to use all
the available heat.
• Make sure that the base of the cookware is always
clean and dry, in order to fully utilise and extend the
life of both the cooking zones and the cookware.
• Avoid using the same cookware which has been
used on gas burners: the heat concentration on gas
burners may distort the base of the pan, causing it
not to adhere correctly.
Safety devices
Pan sensor
Each cooking zone is equipped with a pan sensor
device. The hotplate only emits heat when a pan with
suitable measurements for the cooking zone is placed
on it. If the indicator light is flashing, it may indicate:
• An incompatible pan
• A pan whose diameter is too small
• The pan has been removed from the hotplate.
Buzzer
This can also indicate several irregularities:
• An object (a pan, cutlery, etc.) has been placed on
the control panel for more than 10 seconds.
• Something has been spilt on the control panel.
• A button has been pressed for too long. All of the
above situations may cause the buzzer to sound.
Remove the cause of the malfunction to stop the
buzzer. If the cause of the problem is not removed,
the buzzer will keep sounding and the hob will switch
off.
Overheating protection
If the electronic elements overheat, the hob switches off
F
automatically and appears on the display, followed
by a flashing number. When the temperature has
reached a suitable level, this message disappears and
the hob may be used again.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
9
Low-flame
cooking
Medium-flame cooking
High-flame
cooking
Very high-flame
cooking
Practical cooking advice
Very
low-flame
cooking
GB
ª
•
•
¶
¶
§
§
S
S
¢
¢
£
™
™
¡
Pressure cooking
Pressure cooker
Frying
Grilling
Boiling
Crêpes
Cooking on a high flame and browning
(roasts, steaks, escalopes, fish fillets,
fried eggs)
Fast thickening (liquid juices)
Boiling water (pasta, rice, vegetables)
Milk
Slow thickening (dense juices)
Bain-marie cooking
Low-flame cooking (stews)
Chocolate sauce
Pressure cooking after whistle
Reheating dishes
Keeping food hot
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
10
Precautions and tips
! This appliance has been designed and manufactured
in compliance with international safety standards. The
following warnings are provided for safety reasons and
must be read carefully.
This appliance conforms to the following
European Economic Community directives:
- 2006/95/EEC dated 12/12/06 (Low Voltage) and
subsequent amendments;
- 2004/108/EEC dated 15/12/04 (Electromagnetic
Compatibility) and subsequent amendments;
- 93/68/EEC dated 22/07/93 and subsequent amendments.
- 1275/2008 stand-by/off mode.
General safety
! Make sure that the air inlet behind the fan grille is
never obstructed. The built-in hob should, in fact, be
provided with suitable ventilation for the cooling of the
electronic components used in the appliance.
! We advise against the installation of an induction hob
above an under-the-counter refrigerator (heat) or above
a washing machine (vibration s). In fact, there would
be insufficient space for the ventilation of electronic
components.
• The appliance was designed for domestic use inside the
home and is not intended for commercial or industrial
use.
• The appliance must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain and storms.
• Do not touch the appliance when barefoot or with wet or
damp hands and feet.
• The appliance must be used by adults only for the
preparation of food, in accordance with the instructions
provided in this booklet. Do not use the hob as a worktop
or chopping board.
• The glass ceramic hob is resistant to mechanical shocks,
but it may crack (or even break) if hit with a sharp object
such as a tool. If this happens, disconnect the appliance
from the electricity mains immediately and contact a
Service Centre.
• Ensure that power supply cables of other electrical
appliances do not come into contact with the hot parts of
the hob.
• Remember that the cooking zones remain relatively hot
for at least thirty minutes after they have been switched
off. An indicator light provides a warning when residual
heat is present (see Start-up and use).
• Keep any object which could melt away from the
hob, for example plastic and aluminium objects, or
products with a high sugar content. Be especially
careful when using plastic film and aluminium foil or
packaging: if placed on surfaces which are still hot,
they may cause serious damage to the hob.
• Always make sure that pan handles are turned
towards the centre of the hob in order to avoid
accidental burns.
• When unplugging the appliance, always pull the plug
from the mains socket; do not pull on the cable.
• Never perform any cleaning or maintenance work
without having disconnected the appliance from the
electricity mains.
• The appliance should not be operated by people
(including children) with reduced physical, sensory
or mental capacities, by inexperienced individuals or
by anyone who is not familiar with the product. These
individuals should, at the very least, be supervised
by someone who assumes responsibility for their
safety or receive preliminary instructions relating to
the operation of the appliance.
• For the attention of wearers of pacemakers or
other active implants:
The hob complies with all current standards on
electromagnetic interference.
Your induction hob is therefore perfectly in keeping
with legal requirements (89/336/CEE directives). It
is designed not to create interference on any other
electrical apparatus being used on condition that
the apparatus in question also complies with this
legislation.
Your induction hob generates short-range magnetic
fields.
To avoid any interference between your induction
hob and a pacemaker, the latter must be designed to
comply with relevant regulations.
In this respect, we can only guarantee our own
product conformity. Please consult the pacemaker
manufacturer or your doctor concerning its
conformity or any possible incompatibility.
• Do not let children play with the appliance.
• Do not place metal objects (knives, spoons, pan lids,
etc.) on the hob as they may become hot.
• The appliance is not intended to be operated by
means of an external timer or separate remotecontrol system.
Disposal
• When disposing of packaging material: observe local
legislation so that the packaging may be reused.
• The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the materials
inside the machine, while preventing potential damage
to the atmosphere and to public health. The crossed-out
dustbin is marked on all products to remind the owner of
their obligations regarding separated waste collection.
For further information relating to the correct disposal of
exhausted household appliances, owners may contact
the public service provided or their local dealer.
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
11
GB
Care and maintenance
04/2012 - 195101112.00
XEROX FABRIANO
Switching the appliance off
GB
Disconnect your appliance from the electricity supply
before carrying out any work on it.
Cleaning the appliance
! Do not use abrasive or corrosive detergents (for
example, products in spray cans for cleaning barbecues
and ovens), stain removers, anti-rust products, powder
detergents or sponges with abrasive surfaces: these
may scratch the surface beyond repair.
! Never use steam cleaners or pressure cleaners on the
appliance.
• It is usually sufficient simply to wash the hob using a
damp sponge and dry it with absorbent kitchen towel.
• If the hob is particularly dirty, rub it with a special
glass ceramic cleaning product, then rinse well and
dry thoroughly.
• To remove more stubborn dirt, use a suitable scraper.
Remove spills as soon as possible, without waiting
for the appliance to cool, to avoid residues forming
crusty deposits. You can achieve excellent results
by using a rust-proof steel wire sponge - specifically
designed for glass ceramic surfaces - soaked in
soapy water.
• If any plastic or sugary substances are accidentally
melted on the hob, remove them immediately with
the scraper, while the surface is still hot.
drips during cooking. This maintenance task should
be carried out while the appliance is warm (not hot)
or cold.
• Always remember to rinse the appliance well with
clean water and dry it thoroughly: residues can
become encrusted during subsequent cooking
processes.
Stainless steel frame (only in models with outer frame)
Stainless steel can be marked by hard water which has
been left on the surface for a long time, or by cleaning
products containing phosphorus.
After cleaning, it is advisable to rinse the surface well
and dry it thoroughly. If water is spilt on the surface, dry
it quickly and thoroughly.
! Some hobs have an aluminium frame which is
similar to stainless steel. Do not use any cleaning or
degreasing products which are not suitable for use with
aluminium.
Disassembling the hob
If it is necessary to disassemble the hob:
1. Loosen the screws fixing the alignment springs on
each side.
2. Loosen the screws holding the fixing hooks in each
corner.
3. Take the hob out of its installation cavity.
! Do not attempt to repair the appliance yourself. If the
appliance breaks down, contact a Service Centre.
• Once it is clean, the hob may be treated with a
special protective maintenance product: the invisible
film left by this product protects the surface from
Technical description of the models
The induction system is the quickest existing way of cooking. Unlike traditional hotplates where the cooking zone heats
up, with the induction system heat is generated directly inside pans which have ferromagnetic bases.
Key:
I = single induction cooking zone
B = booster: the power level of the cooking zone may be boosted to 3000 W
* = the maximum power level is limited while the booster is activated for the relevant rear cooking zone (see Start-up
and use).
Hobs
CIO 632 CC S
Cooking zone
Back Left
Back Right
Front Left
Front Right
Total power
Power (W)
I 1400
I 2200 – B 3000* - 1600 if Front Right*
I 1400
I 1400 – B 2000* – 600 if Back Right*
6400
PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24
12
">