- Vehicles & accessories
- Motor vehicle electronics
- Car audio amplifiers
- Audiovox
- BTR120
- Owner's manual
advertisement
▼
Scroll to page 2
of 12
Model AMP-604 240 Watt 4-Channel Power Amplifier Ow ne r's Manual INDEX Specifications ...........................................................1 Precautions ..............................................................2 Installation Instructions .............................................3 Wiring Instructions ............................................4 - 5 Input Wiring Diagram ............................................6 Output Wiring Diagram .........................................7 Operation ................................................................8 Warranty .................................................................9 HIGH PERFORMANCE STEREO AMPLIFIER This power amplifier has been designed to provide high quality performance with a minimum of maintenance. However, it's performance will only be as good as the care and quality of components with which it is installed. We therefore advise that you read these instructions very carefully to familiarize yourself with the product and it's features. Should you require assistance with the installation or wiring of this unit, please call our toll-free "HELP" line at 1-800-645-4994 during the days/hours shown. HELP! 1-800-645-4994 Monday - Friday Saturday 8:30am - 7:00pm Eastern 9:00am - 5:00pm Eastern SPECIFICATIONS Maximum Output Power: Output Impedance: Frequency Response: Channel Separation: Signal / Noise Ratio: Input Impedance: 60 watts x 4 @ 4 ohms 4 - 8 ohms 20 - 25,000 Hz. ± 1 dB 50 dB 80 dB (A-Weighted) low-level 10K ohms high-level 100 ohms Input Sensitivity: low-level 200 mv. - 2 v. high-level 2 - 10 v. Supply Voltage: 12 volts, negative ground Fuse Rating: 10 amps. Dimensions (W x H x D): 6-3/8" x 2-1/8" x 9-1/10" 162 mm x 54 mm x 231 mm * Due to continuing improvement, Audiovox reserves the right to change features and design without notice. -1- PRECAUTIONS 1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive (+) terminal of the battery. Connect this wire only after having completed and checked all other connections to the amplifier. 3. By nature of its design, a power amplifier generates heat and requires good air circulation around it to dissipate that heat. Do not install the amplifier in an enclosed area which does not permit adequate air circulation. Should the temperature of the unit rise too high, the internal thermal sensors will shut off operation until it has cooled down sufficiently. 4. If fuse replacement is necessary, use only fuses of the same ampere rating as originally supplied with the unit. The use of fuses with incorrect ratings may cause serious damage to the amplifier. If fuses blow consistently, carefully check all electrical connections to the unit. 5. Supply of adequate battery voltage is critical to the proper operation of the power amplifier. The leads to the battery and chassis ground must be of a thick enough gauge to provide this voltage to the amplifier. We recommend #18 gauge wire or thicker (smaller gauge #) for the battery and ground leads. 6. Make certain that the speakers to be used with this amplifier are capable of handling the output power (wattage) of the unit. Use of speakers not rated for the output of this amplifier may cause damage to or failure of the speakers for which Audiovox will not be liable. -2- INSTALLATION DIAGRAM INSTALLATION INSTRUCTIONS 1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode. SELF-TAPPING SCREW 2. Place the amplifier on the mounting surface and mark the locations of the four mounting holes as shown in the illustration. 3. Remove the amplifier and drill a 1/8" hole at each of the four locations. CAUTION: Before drilling the holes, look at the underside of the mounting surface. Always check carefully to avoid drilling into wiring, braces, fuel or brake lines. CHECK BEFORE YOU DRILL ! 4. Secure the amplifier to the mounting surface using the self-tapping screws provided. MOUNTING SURFACE -3- 1/8" DIA. HOLE WIRING INSTRUCTIONS The power connections for this amplifier are made via screw tightened terminal blocks. Loosen the screw for the connection to be made and fully insert the wire (strip 1/2" of insulation from the end) into the respective screw on the side panel (crimp-on "U" terminals are provided to simplify wiring and we recommend their use.) Tighten the screw down to secure the wire. 1. Power Connection The battery terminal (BATT) must be connected directly to the positive terminal of the vehicle battery to provide an adequate voltage source and minimize noise. Connecting the battery terminal lead to any other point (such as the fuse block) will reduce the power output and may cause noise and distortion. Use only #18 gauge or thicker (smaller gauge #) wire for this lead and connect it to the terminal of the battery after all other wiring is completed. 2. Ground Connection The ground terminal (GND) connection is also critical to the correct operation of the amplifier. Use a wire of the same gauge as the power connection (#18 or thicker) and connect it between the ground terminal (GND) of the amplifier and a metal part of the vehicle close to the mounting location. This wire should be as short as possible and any paint or rust at the grounding point should be scraped away to provide a clean metal surface to which the end of the ground wire can be screwed or bolted. 3. Remote Turn-On Connection The amplifier is turned on by applying +12 volts to the remote turn-on terminal (REM). The wire lead to this terminal should be connected to the "Auto-Antenna" lead from the car stereo which will provide the +12 volts only when the car stereo is turned on. If the car stereo does not provide an Auto-Antenna lead, the remote turn-on lead may be wired to an "Accessory" or "Radio" terminal in the car's fuse block. This will turn the amplifier on and off with the ignition key, regardless of whether the car stereo is on or off. The remote turn-on lead does not carry large currents, so #20 gauge wire may be used for this application. -4- WIRING INSTRUCTIONS 4. Speaker Connections Wire the speakers to the "Speaker Output" terminals as per the Output Wiring Diagram (remove 1/4" of insulation from the end of each wire, depress the spring tab on the connector, insert the wire and release the spring tab). For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge. When wiring the speakers, pay careful attention to the polarity of the terminals on the speakers and make certain they correspond to the polarity of the corresponding terminals on the amplifier. DO NOT ground any speaker leads to the chassis of the vehicle. 5. Input Connections This amplifier features both high and low-level input capability. Use either the low-level or high-level inputs, not both. If low-level outputs are provided from the car stereo, it is recommended that the low-level inputs be used for lowest distortion and best performance. Use good quality shielded audio cables with RCA plugs at both ends to connect the stereo to the amplifier and keep the cable lengths to a minimum to avoid noise. If the car stereo does not provide low-level outputs, the amplifier may be connected via the speaker (high-level) outputs from the stereo. Wire the positive (+) speaker leads from the car stereo to the 5-pin adaptor harness as shown in the diagram (shielded cable is not required for this application) and plug the connector into the mating High-Level Input socket on the amplifier. Carefully splice and insulate all wire connections. CAUTION: Use either the low-level or the high-level inputs on the amplifier. DO NOT use both input levels at the same time. -5- INPUT WIRING DIAGRAM LOW-LEVEL RCA OUTPUTS RIGHT FRONT CAR STEREO HIGH-LEVEL (SPEAKER) OUTPUTS RIGHT REAR + LEFT REAR + RIGHT FRONT + LEFT FRONT + LEFT FRONT LEFT REAR NOTE: When using High-Level (Speaker) Outputs of car stero, connect only the Positive (+) wires to the amplifier. Do not use Negative (–) Output wires (insulate ends with tape and leave disconnected). CHASSIS GROUND ON RADIO RIGHT REAR RCA TYPE SHIELDED CABLES (NOT INCLUDED) GRAY BLACK BROWN WHITE GREEN IMPORTANT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUTS, NOT BOTH. 5-PIN CONNECTOR LOW INPUT HIGH LEVEL PWR TO CH4 TO CH3 TO CH1 TO CH2 -6- MIN MAX MIN MAX GAIN GAIN l l l l WARNING! OUTPUT WIRING DIAGRAM THIS AMPLIFIER IS DESIGNED FOR USE WITH 4 SPEAKERS NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS. NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND. FAILURE TO WIRE CORRECTLY MAY CAUSE DAMAGE TO THE AMPLIFIER. LEFT FRONT SPEAKER 4 - 8 OHMS EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT OR GREASE FROM AREA FOR GOOD CONNECTION GROUNDED METAL SECTION OF VEHICLE m m + m + m LEFT REAR SPEAKER 4 - 8 OHMS USE #18 GAUGE WIRE (SEE TEXT) CONNECT THIS WIRE LAST FUSE BATT CHASSIS GROUND POWER REM GND SPEAKER OUTPUT 12 VOLT VEHICLE BATTERY AUTO-ANTENNA LEAD RIGHT FRONT SPEAKER 4 - 8 OHMS CAR STEREO -7- + m + m m m RIGHT REAR SPEAKER 4 - 8 OHMS OPERATION 2 3 2 1 FUSE LOW INPUT HIGH LEVEL POWER BATT REM GND SPEAKER OUTPUT PWR MIN MAX GAIN MIN MAX GAIN After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. increase the output from the system. If, however, there is still output from the amplifier when the car stereo volume control is at its minimum setting, or the output level increases too fast with a small rotation of the volume control, adjust the Level control to decrease the output from the system. Once the correct setting is found, these controls should not require any further adjustment. 1 Power Indicator LED The Power Indicator LED will light to indicate that the unit is connected to the battery and that the Remote Turn-On terminal is receiving +12 volts, thus turning on the amplifier. 3 Fuse 2 Level (Gain) Controls The circuitry of the amplifier is protected from damage by an automotive-type fast-blow fuse. If fuse replacement is necessary, use only fuses of the same ampere rating as originally supplied with the unit. The use of fuses with incorrect ratings may cause serious damage to the amplifier. If fuses blow consistently, carefully check all electrical connections to the unit. The amplifier is capable of operating from sources supplying a wide range of input levels. The Level control should initially be set to the mid-rotation position. If it is found that there is not enough output even when the volume control on the car stereo is at its maximum setting, adjust the Level control of the respective channels to -8- 90 DAY/12 MONTH LIMITED WARRANTY Applies to car stereo power amplifiers, equalizers and accessories. AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor. After the initial 90 day period and for a period of 12 months from the date of original purchase, the Company will supply at no charge a replacement for any defective part(s) but will charge for the labor to repair the product. To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to an approved warranty station or the Company at the address shown below. This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred for installation, removal or reinstallation of the product, or damage to tapes, compact discs, speakers, accessories, or vehicle electrical systems. This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state. U.S.A. : AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 l 1-800-645-4994 CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA -9- 128-5422A © 2001 Audiovox Electronics Corp., Hauppauge, NY 11788 Printed in Korea 128-6017
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project