Proudly distributed by
De’Longhi Australia Pty Limited
P.O. BOX 4540
CASULA MALL NSW 2170
Customer Service Ph: 1800 126 659
Fax: 1800 706932
www.delonghi.com.au
e-mail: [email protected]
De’Longhi Appliances via Seitz, 47 31100 Treviso Italia
5711010781/10.13
De’Longhi New Zealand Limited
25 Carbine Road
Mt Wellington
Auckland, New Zealand
P.O. Box 58-056 Botany
MANUKAU 2163
Customer Service Ph: 0508 200 300
Fax: 0508 200 301
www.delonghi.com.nz
e-mail:[email protected]
TRD41500ET - TRD42400ET
DRAGON 4 OIL FILLED RADIATOR
Instructions for use
DESCRIPTION
A
B
G
C
F
D
E
H
I
L
2
INSTRUCTIONS FOR USE
Read these instructions carefully before using the appliance.
Failure to comply with these instructions can lead to injury to
persons and damage to the machine. The manufacturer is not
liable for damage deriving from the failure to comply with the
user instructions.
-
Symbols used in these instructions
Important warnings are identified by the symbols below.
It is important to respect the warnings. Failure to respect the
warnings could lead to electric shock, serious injury, burns, fire
or damage to the appliance.
-
Danger!
Failure to observe the warning may result in life threatening
injury by electric shock.
-
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Danger of burns!!
Do not rest the power cable on hot elements.
WARNING: In order to avoid overheating, never
under any circumstances cover the appliances
during operation, as this would lead to dangerous
overheating.
Danger of burns!!
Failure to observe the warning could result in burns or scalds.
­
Please note:
This symbol indicates recommendations and important
information for the user.
-
SAFETY WARNINGS
-
Danger!
As the appliance operates using electricity, electric shocks can
not be excluded.
Therefore, follow the safety recommendations given:
- To avoid risk of cable overheating, extension leads must
not be used in powering this appliance.
- If the power cable is damaged, it must be replaced by the
manufacturer or an authorised service centre in order to
eliminate all risk. Please contact Customer Experience, see
enclosed guarantee.
- Do not use the heater in a bathroom or in the vicinity of
bathtubs, washbasins, showers or swimming pools.
-
use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the appliance.
The heater must be positioned at least 50cm from furniture
or other objects.
Do not use this appliance in rooms measuring less than
4m².
Do not place items over the radiator (such as to dry
washing).
In order to avoid a hazard due to inadvertent resetting of
the thermal cutout, this appliance must not be supplied
through an external switching device such as a timer, or
connected to a circuit that is regularly switched on and off
by the utility.
-
-
Important!
The appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
-
3
Please note:
The appliance must not be placed immediately under a
fixed power socket.
The power cord should be fully removed from the cord
storage unit when in use.
The appliance is fitted with a tilt-switch which turns the
appliance off if it should fall over.
To restart the appliance, simply place it upright again.
Always use the radiator in the vertical position.
When you turn the appliance on for the first time, operate
it at maximum for at least two hours.
It is normal for the appliance to make "creaking" noises
when first turned on.
In order to eliminate the radiator’s “new” smell, set it to
maximum power for at least a few hours when used for
the first time. During this operation, the room in which the
radiator is located must be ventilated.
This appliance is filled with a precise quantity of oil and
repairs requiring it to be opened must be carried out by the
manufacturer or an authorised technical assistance centre
only. In the event of oil leaks, please contact Customer
Experience, see enclosed guarantee.
As with any electrical appliance, whilst the instructions
aim to cover as many eventualities as possible, caution
and common sense should be applied when operating your
-
appliance, particularly in the vicinity of young children.
A safety device will turn the radiator off. To reset, contact
the technical assistance service.
Fig. 1
Use in compliance with intended use
Use this heater only as described in this manual. All other use is
considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from
improper use of the appliance. This is a household appliance
only. It is not intended to be used in:
• staff kitchen areas in shops, offices and other working
environments;
• farm houses;
• by clients in hotels, motels and other residential type
environments;
• bed and breakfast type environments.
Use in this manner will invalidate the manufacturers warranty.
Location
The heater must not be placed immediately below a power
outlet. Do not use this radiator in rooms having a surface area
of less than 43 square feet (4 sq.m.).
Power connection
Electrical connection
- Before plugging the radiator into the mains, check that
your supply voltage is the same as that shown on the
rating plate of the appliance.
- If using more than one radiator at a time, it is important
to ensure that the house mains is adequate to cope with
the power requirements.
- It is important to ensure that the socket is adequately
earthed.
- This appliance complies with directive 2004/108/ec on
electromagnetic compatibility.
The appliance will be set in the stand-by condition.
The display will show the
symbol. Keep loose clothing
or bedding, furniture and flammable material away from
the power outlet where the heater is plugged in. After an
interruption of the power supply (power failure or appliance
unplugged) the unit always reverts to off. When the unit
is switched on by pressing the on-standby button, the
operating conditions will be the same ones previously set.
Introduction
Thank you for choosing the TRD Oil Filled Radiator. We hope you
enjoy using your new appliance.
Take a few minutes to read these instructions.
This will avoid all risks and damage to the appliance.
DESCRIPTION
(see figure on pag. 2).
The terminology below will be used repeatedly in the
following pages.
A Display
B On-standby button
C Power button
D Decrease button
E Increase button
F Timer button
G Brightness button
H Eco button
I Cord holder
L Easy wheels
First use
The first time the appliance is used, run it at the maximum
power for at least two hours.
During this time, ventilate the room thoroughly to eliminate
the “new” smell released by the appliance. It is completely
normal for the appliance to emit “creaking” sounds the first
time it is run.
USE
"Easy wheel" system
Heating
Turn the radiator upside down on a rug or a soft surface in
order to prevent damaging the paint finish.
Fully unfold the wheels by turning them outwards (Fig. 1).
Turn the radiator back to its upright position.
To turn the appliance on, press the
(B) button.
Press button
(C) to set the required power level:
MIN ( ); MED (
); MAX (
).
To select the desired temperature, press button + or - (E or D).
By pushing the + or - button once, the temperature (shown
4
Brightness of the display
on the display) will increase or decrease by 1°C.
Keeping the + or - button depressed the value will increase
or decrease rapidly.
The appliance allows to set the temperature from 5° to 28°C.
The appliance allows two different brightness settings for the
display.
The highest is active when any key button is pressed.
After a few seconds of keyboard inactivity, the brightness will
decrease to the operating brightness level.
This lower level can be adjusted by means of the light button
(G). Press the light button repeatedly until the desired
brightness is reached (three brightness levels available).
Anti-freeze function
Key lock
Setting the temperature to 5°C with the "-" button, the
appliance will activate the Antifreeze function. The display
will show the
symbol, in this way the appliance will
turn on automatically, at the max power, only if the room
temperature falls below 5°C, to prevent freezing conditions.
If you wish to go back to the Heating function, press the "+"
button once.
In order to avoid accidental operation, you can lock the
keyboard using the keylock function.
To activate this function press buttons + and - together for
at least 3 seconds. The display shows the symbol and a
double acoustic signal will be emitted. To deactivate the
function proceed in the same way.
Timer function
Eco function
This function can be activated in two different ways.
Delayed start: With the appliance on-standby, press the
timer button (F) .
The symbol is displayed flashing together with the hours
left before the appliance comes on.
Change the hours using the + and - buttons, then wait a few
seconds for the program to be stored.
The display will return to off and the symbols remains on.
When the programmed time has elapsed, the appliance will
come on with the previous settings.
When this function is active the appliance automatically sets
the most appropriate power level to guarantee optimum
comfort while reducing energy consumption. To activate this
function press the "ECO" (H) button. The display will show
symbol.
If the selected temperature is much higher then the actual
room temperature, the appliance will start automatically and
heat the room rapidly.
The appliance will automatically select the most economical
power level (MAX-MED-MIN-OFF).
If MAX power level has been selected using the
button, the appliance will cycle between: MAX-MED-MINOFF.
If MED power level has been selected, the appliance will cycle
between: MED-MIN-OFF.
If MIN power level has been selected, the appliance will cycle
between: MIN-OFF.
Delayed stop: with the appliance on, press the timer button
. The
symbol is displayed flashing together with the
hours left before the appliance goes on-standby. Change the
hours using the + and - buttons, then wait a few seconds for
the program to be stored.
The current settings and symbol are displayed.
At the end of the set time the appliance switches on-standby
automatically. To go back to operating without the timer,
press the timer button twice.
The timer symbol disappears from the display.
Note: the time is settable from 0.5 to 24 hours.
Working indicator
The symbol
colors.
indicates the heating status by means of its
RED: the unit is heating at the maximum power.
YELLOW: the unit is heating at the medium power.
GREEN: the unit is heating at the minimum power.
Changing of the temperature scale
absent: the unit is not heating.
The display can show the temperature in both °F (Fahrenheit)
and °C (Celsius). To select the desired temperature scale,
5
when the unit is in standby position, press and hold the "+"
and "ECO" keys for at least 10 seconds, then release.
The change of scale will be indicated by two short beeps.
and store the appliance in a dry place. This appliance has
been made to last many years without problems. In the
event of malfunction or doubt, do not try and repair on your
own. There would be the danger of fire or electric shock.
Please refer to the enclosed guarantee leaflet for service and
assistance details.
Alarms
The appliance has a diagnostic system that makes it possible
to signal malfunctions.
In case of problems, the display will show an alarm message:
(Product failure)
With this alarm the appliance does not
operate. Check if the appliance is correctly
positioned. If the problem persists, contact
the nearest Customer Experience.
(High temperature)
When the product’s internal temperature
is too high, the heating power will
progressively and automatically be
reduced. The display shows
for two
seconds, on and off. To remove the cause
of this alarm check that the unit is not
covered or obstructed.
Safety device
A safety device shuts the radiator down in the case of
overheating. To start the radiator up again, contact Customer
Experience. See enclosed guarantee leaflet.
MAINTENANCE AND SERVICE
Before performing any operations on the appliance, always
unplug from the mains socket and leave to cool.
Wipe the radiator with a soft damp cloth without using
detergents or abrasives. If the radiator is not to be used for
a long period of time, wrap the cable around the cable tidy
TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
The appliance doesn't - Be sure it is plugged in and that the electrical - Plug into the power outlet.
work
outlet is working.
- Check for any obstruction.
- Remove the obstruction and let the
appliance cool down. If the appliance
doesn't work please contact Customer
Experience.
- The temperature may be set too low.
- Set the temperature to a higher position.
- The Key lock may be activated.
- See the section "Key lock".
6
">
