Acer Laptop 1360 Series User manual

Aspire 1360/1520 Series
Service Guide
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on Aspire 1360/1520 service guide.
Date
2004/10/20
II
Chapter
Chapter 1
Updates
Add the most up-to-date system block diagram on page 3.
Change the memory controller to “built-in CPU” on page 18.
Copyright
Copyright © 2004 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
Screen messages
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Table of Contents
Chapter 1
System Introduction
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Left view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Chapter 2
System Utilities
32
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Chapter 3
Machine Disassembly and Replacement
46
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Removing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Removing the Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the Wireless LAN Board and the Modem Board . . . . . . . . . . . . . . . . . . . .52
Removing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Disassembling the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Removing the Middle Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Removing the Launch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Disassembling the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Removing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Removing the Inverter Board (15” LCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Removing the 15” TFT LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Removing the LCD Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Removing the LCD Coaxial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Removing the LCD Hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Disassembling the Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Removing the RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
VII
Table of Contents
Removing the Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Removing the Thermal Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Removing the Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Installing the Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Removing the Upper Case Assemly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Removing the Touchpad Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Removing the Touchpad Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Removing the VGA Thermal Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Removing the CPU Heatsink Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Removing the Second Fan Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Removing the ODD Module(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Removing the ODD Module(2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Removing the HDD Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Removing the Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Removing the DC Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Removing the I/O Port Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Removing the PCMCIA Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Removing the Speaker Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
System Upgrade Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Base Unit to Wireless Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Chapter 4
Troubleshooting
72
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
External Diskette Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
External CD-ROM Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Keyboard or Auxiliary Input Device Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Memory check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Power System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Touchpad Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Power-On Self-Test (POST) Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
POST Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
How to Build NAPP Master Hard Disc Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
CD to Disk Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Disk to Disk Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Chapter 5
Jumper and Connector Locations
98
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Chapter 6
FRU (Field Replaceable Unit) List
100
Aspire 1660 Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Appendix A Model Definition and Configuration
112
Model Name Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Appendix B Test Compatible Components
114
Microsoft Windows XP Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Appendix C Online Support Information
120
VIII
IX
Chapter 1
System Introduction
Features
This computer was designed with the user in mind. Here are just a few of its many features:
Performance
T
Mobile AMD SempronTM processor 2600+ to 3300+ or higher with 128/256 KB L2 cache,
supporting AMD Power Now! Technology and HyperTransport technology (for Aspire 1360 only)
T
AMD Athlon 64 processor 3000+ to 3400+ or higher with 1 MB cache, supporting HyperTransport
technology (for Aspire 1520 only)
T
VIA Chipset-integrated Unichrome PRO graphics core, with up to 64MB of shared memory
T
256/512MB of DDR333 SDRAM, upgradeable to 2048MB with dual soDIMM modules
T
30GB and above high-capacity, Enhanced-IED hard disk (for Aspire 1360 only)
T
40GB and above high-capacity, Enhanced-IDE hard disk (for Aspire 1520 only)
T
Advanced Configuration Power Interface (ACPI) power management system
T
The TFT LCD panel providing a large viewing area for maximum efficiency and ease-of-use:
Display
-- 14.1” XGA (1024x768) resolution (for Aspire 1360 only)
-- 15.0” XGA (1024x768) or SXGA+ (1400x1050) resolution
-- 15.4” WXGA (1280x800)
T
NVIDIA GeForce4 448 Go with 64MB of video memory (manufacturing option)
T
NVIDIA GeForce FX Go5200 with 64MB of video memory (manufacturing option)
T
NVIDIA GeForce FX Go5700 with 64MB of video memory (manufacturing option)
T
3D graphics support
T
Support simultanesous display between LCD and CRT
T
S-video for output to a television or display device that supports S-video input
T
“Automatic LCD dim” feature, automatically selecting the best setting for the display in order to
conserve power
T
DualViewTM support
Multimedia
T
High-speed built-in optical drive:
DVD/CD-RW Combo, or DVD-Dual or DVD Super-Multi
T
MS DirectSound compatible
T
Built-in dual speakers
Connectivity
Chapter 1
T
Integrated 10/100 Mbps Fast Ethernet connection (for Aspire 1360 only)
T
Integrated 10/100/1000 Mbps Fast Ethernet connection (for Aspire 1520 only)
T
Built-in 56Kbps fax/data modem
1
T
Four Universal Serial Bus (USB) 2.0 ports
T
One IEEE 1394 port
T
IEEE 802.11b/g Wireless LAN (manufacturing option)
T
Bluetooth® (manufacturing option)
Expansion
T
One Type III or two Type II CardBus PC Card slots
T
Upgradeable hard disk and memory modules
Human-centric design
T
Rugged, yet extremely portable, construction
T
Stylish appearance
T
Full-size keyboard with four programmable launch keys
T
Comfortable palm rest area with well-positioned touchpad
T
Two Type II or one Type III PC CardBus (PCMCIA) slot
T
One IEEE 1394 port
T
One FIR port
T
One RJ-11 modem jack (V.92, 56K)
T
One RJ-45 network jack(Ethernet 10/100 Base-T)
T
One DC-in jack
T
One parallel port (ECP/EPP)
T
One S-video port
T
One external monitor port
T
One microphone-in jack (3.5mm mini jack)
T
One headphone jack (3.5mm mini jack)
T
Four USB 2.0 ports
I/O Ports
2
Chapter 1
2
3
4
27
29
RJ45
30
Mini-PCI
802.11a/b/g
1394
Conn
27
PCMCIA
SLOT
Support
TypeII
29
TXFM
29
TXFM
PCMCIA I/F
1000Mb
10/100Mb
27
PWR SW
TPS2224AP
LAN PHY
VIA VT6103L 29
PCI GIGA LAN
Realtek
28
RTL8110SBL
C
23
23
DVD/
CD-RW
ATA 133
ACPI 2.0
19,20,21
LPC I/F
6-CH
AC97 2.2
6xUSB 2.0
VT8235CE
VIA
HDD
MII
PCI
37
Parallel
port
36
Thermal
& Fan
G791 22
8,9,10
34
Touch
Pad
Int.
KB
KBC
M38859
OP AMP
APA2020 32
31
34
33
RGB CRT
LVDS
SVIDEO/COMP
DDR x2
200-PIN DDR SODIMM
D
AC'97 CODEC
VT1612A
LPC Bus / 33MHz
29
RJ11
CONN
TFDU6101E
36
FIR
24
MODEM
MDC Card
AC LINK
24
16
Graphic CONN.
AGP 8X
15
LVDS Transmitter
VIA VT1631
14
TV Encoder
VIA VT1623M
DDR 333/400
USB x 4
NS SIO
PC87392
AGP 8x
8 bit V-LINK
66MHZ
8x/4x/2x
11,12,13
AGTL+ CPU I/F + UMA
K8N800
VIA
HyperTransport
6.4GB/S 16b/8b
4,5,6,7
Claw Hammer K8
AMD CPU
EGRET Block Diagram
PCI Bus / 33MHz
25,26
2* Slot Cardbus
1* 1394
TI
PCI 7420
3
CLK GEN
ICS
ICS950405
B
PIDE
Chapter 1
SIDE
A
17
18
SST-49LF040
FWH
32
Int. SPKR
32
Line Out
(SPDIF)
Line In 32
MIC In
CRT
LCD
TVOUT 17
35
DCBATOUT
OUTPUTS
INPUT
OUTPUT
5V_S5 ,
3D3V_S5
INPUT
OUTPUT
VCC_CORE_S0
OUTPUT
5V_S3
3D3V_S5
3D3V_S3
3D3V_S0
DCBATOUT
INPUT
2D5V_S5
5V_S0
3D3V_S3
3D3V_S0
3D3V_LAN_S3
1D8V_S0
+5V_AUX_S5
+5V_UP_S5
2D5V_S0
OUTPUT
FDD6035AL/FDS9412-U
FDS9412-U/SI4892DY/LP2951ACM
APL5508-18VC/APL5308-25AC
SYSTEM POWER 44,45
DCBATOUT
INPUT
ISL6559CR
2D5V_S3
1D5V_S0
44
43
46
CPU V_CORE 41,42
DCBATOUT
2D5V_S3
TPS5110
SYSTEM DC/DC
DCBATOUT
MAX1999
SYSTEM DC/DC
AD+
BAT+
INPUTS
MAX1645BEEI
Battery Charger
L1: Signal 1
L2: GND
L3: Signal 2
L4: Signal 3
L5: VCC
L6: Signal 4
PCB Layer Stackup
E
2
3
4
System Block Diagram
3
Board Layout
Top View
4
1
Line-in Port
15
CPU Socket
2
Line-out Port
16
North Bridge
3
RJ45+RJ11
17
Fan Connector
4
LCD Inverter Cable Connector
18
Note: There is no 18 on this main board.
5
USB Port
19
Touchpad Cable Connector
6
USB Port
20
HDD Connector
7
USB Port
21
Keyboard Connector
8
USB Port
22
Speaker Cable Connector
9
VGA Port
23
Optical Drive Connector
10
S-Video Port
24
South Bridge
11
LCD Coaxial Cable Connector
25
RTC Battery Connector
12
Parallel Port
26
Launch Board Cable Connector
13
DC-in Port
27
SW1 (Please see Chapter 5 for its settings)
14
LCD Lid Switch
28
PCMCIA Slot
Chapter 1
Bottom View
1
Wireless LAN Card Connector
5
FIR Port
2
Modem Board Connector
6
DIMM Socket 1
3
Modem Cable Connector
7
DIMM Socket 2
4
IEEE 1394 Port
8
DC Charger Board Connector
Chapter 1
5
Panel
Ports allow you to connect peripheral devices to your computer as you would with a desktop PC.
Front View
#
6
Item
Description
1
Display screen
Liquid-Crystal Display (LCD) provides visual output.
2
Status indicators
LEDs (Light Emitting Diodes) that turn on and off to show
the status of the computer and its functions and
components.
3
Power button
Turns the computer on and off.
4
Launch Keys
Buttons for launching frequently used programs.
5
Palmrest
Comfortable support area for your hands when you use the
computer.
6
Click buttons & 4-way scroll key
The left and right buttons function like the left and right
mouse buttons, the center button serves as a scroll up/
down button.
7
Touchpad
Touch-sensitive pointing device which functions like a
computer mouse.
8
Keyboard
Inputs data into your computer.
9
Ventilation Slot
Enables the computer to stay cool, even after the
prolonged use.
Chapter 1
Left view
#
Icon
Item/ Port
Description
1
PC Card slots
2
Eject button
Eject PC cards from the card slots.
3
Optical drive
Internal optical drive; accepts CDs or DVDs
depending on the optical drive type.
4
IEEE 1394 port
Connects to IEEE 1394 devices.
5
Infrared port
Interfaces with infrared devices (e.g., infrared
printer, IR-aware computer).
6
LED indicator
Lights up when the optical drive is active.
7
Eject button
Ejects the optical drive tray from the drive.
8
Emergency eject slot
Ejects the optical drive tray when the computer is
turned off. There is a mechancial eject button on
the CD-ROM or DVD-ROM drive. Simply insert
the tip of a pen or paperclip and push to eject the
tray.
9
Speaker
Delivers stereo audio output.
Chapter 1
Supports two Type II or one Type III CardBus PC
Card(s).
7
Right View
#
8
Item/ Port
Description
1
Speaker
Delivers stereo audio output.
2
Ventilation slots
Enable the computer to stay cool, even after
prolonged use.
3
Security keylock
Connects to a Kensington-compatible
computer security lock.
Chapter 1
Rear Panel
l
#
Icon
Port
Description
1
Power Jack
Connects to an AC adapter
2
Parallel port
Connects to a parallel device (e.g., parallel
printer)
3
Ventilation slots
Enable the computer to stay cool, even
after prolonged use.
4
S-video port
Connects to a television or display device
with S-video input.
5
External display port
Connects to a display device (e.g., external
monitor, LCD projector).
6
Four USB 2.0 ports
Connects to any Universal Serial Bus
devices(e.g., USB mouse, USB camera).
7
Network jack
Connects to an Ethernet LAN network
8
Modem jack
Connects to the phone line
9
Speaker/line-out/
headphone jack
Connects to audio line-out devices (e.g.,
speakers and headphones).
10
Line-in/mic-in jack
Accepts audio line-in devices (e.g., audio
CD player and stereo walkman).
Chapter 1
9
Bottom View
#
10
Item
Description
1
Battery bay
Houses the computer’s battery pack.
2
Battery release latch
Unlatches the battery to remove the battery pack.
3
Memory compartment
Houses the computer’s main memory.
Chapter 1
Indicators
The computer provides an array of seven indicators located below the display screen, showing the status of
the computer and its components.
The Power and Sleep status icons are visible even when you close the display cover so you can see the status
of the computer while the cover is closed.
#
Icon
Function
InviLink
Description
Indicates status of wireless or Bluetooth
(optional) communications.
Orange--WLAN; Blue--Bluetooth
Chapter 1
1
Power
Lights when the computer is on.
2
Sleep
Lights when the computer enters Standby
mode and blinks when it enters into or
resumes from hibernation mode.
3
Media Activity
Lights when the floppy drive, hard disk or
optical drive is active.
4
Battery Charge
Lights when the battery is being charged.
5
Caps Lock
Lights when Caps Lock is activated.
6
Num Lock
Lights when Numeric Lock is activated.
11
Keyboard
The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and
twelve function keys.
Special keys
Lock keys
The keyboard has three lock keys which you can toggle on and off.
Lock key
Caps Lock
Description
When @is on, all alphabetic characters typed are in uppercase.
@
Num Lock (Fn-F11)
]
12
When ] is on, the embedded keypad is in numeric mode. The keys function
as a calculator (complete with the arithmetic operators ), -, *, and /). Use this mode
when you need to do a lot of numeric data entry. A better solution would be to
connect an external keypad.
Scroll Lock (Fn-F12)
When [ is on, the screen moves one line up or down when you press the up
[
or down arrow keys respectively. [ does not work with some applications.
Chapter 1
Embedded numeric keypad
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired access
Num lock on
Num lock off
Number keys on embedded
keypad
Type numbers using embedded keypad in a
normal manner.
Cursor-control keys on embedded
keypad
Hold Shift while using cursor-control keys.
Hold Fn while using cursor-control
keys.
Main keyboard keys
Hold Fn while typing letters on embedded
keypad.
Type the letters in a normal manner.
Chapter 1
13
Windows keys
The keyboard has two keys that perform Windows-specific functions.
Keys
Windows logo key
Description
Start button. Combinations with this key perform shortcut functions. Below
are a few examples:
+ Tab (Activates next taskbar button)
+ E (Explores My Computer)
+ F (Finds Document)
+ M (Minimizes All)
j+
+ M (Undoes Minimize All)
+ R (Displays the Run... dialog box)
Application key
14
Opens a context menu (same as a right-click).
Chapter 1
Hot Keys
The computer employs hot keys or key combinations to access most of the computer’s controls like screen
contrast and brightness, volume output and the BIOS Utility.
To activate hot keys, press and hold the Fn key before pressing the other key in the hot key combination.
Hot Key
Icon
Function
Description
Fn-l
Hotkey help
Displays a list of the hotkeys and their functions.
Fn-m
Setup
Accesses the notebook configuration utility.
Fn-n
Power Management
Scheme Toggle
Switches the power management scheme used by the
computer (function available if supported by operating
system).
Fn-o
Sleep
Puts the computer in Sleep mode.
Fn-p
Display toggle
Switches display output between the display screen,
external monitor (if connected) and both the display
screen and external monitor.
Fn-q
Screen blank
Turns the display screen backlight off to save power.
Press any key to return.
Fn-r
Touchpad toggle
Turns the internal touchpad on and off.
Fn-s
Speaker toggle
Turns the speakers on and off; mutes the sound.
Fn-w
Volume up
Increases the sound volume.
Fn-y
Volume down
Decreases the sound volume.
Fn-x
Brightness up
Increases the screen brightness.
Chapter 1
15
Hot Key
Icon
Function
Description
Brightness down
Decreases the screen brightness.
Fn-{
Home
Functions as the g key.
Fn-}
End
Functions as the d key.
aGr-Euro
Euro
Types the Euro symbol.
Fn-¨z
The Euro symbol
If your keyboard layout is set to United States-International or United Kingdom or if you have a keyboard with a
European layout, you can type the Euro symbol on your keyboard.
NOTE: for US keyboard users: The keyboard layout is set when you first set up Windows. For the Euro
symbol to work, the keyboard layout has to be set to United States-international.
To verify the keyboard type:
1.
Click on Start, Control Panel.
2.
Double-click on Regional and Language Options.
3.
Click on the Language tab and click on Details.
4.
Verify that the keyboard layout used for “En English (United States) is set to United States-International.
If not, select and click on ADD; then select United States-International and click on OK.
5.
Click on OK.
To type the Euro symbol:
16
1.
Locate the Euro symbol on your keyboard.
2.
Open a text editor or word processor.
3.
Hold aGr and press the Euro symbol.
Chapter 1
Launch Keys
Located at the top of the keyboard are six buttons. These buttons are called lauch keys. They are designated
as mail button, Web browser button, P1, P2, Bluetooth and Wireless buttons. The Wireless and Bluetooth
buttons cannot be set by the user. To set the other four launch keys, run the Acer Launch Manager.
#
Icon
Function
Description
1
Mail
Launches email application
2
Web browser
Launches Internet browser application
3
e
User-programmable
4
P
User-programmable
5
Bluetooth (optional)
Enables your Bluetooth
6
Wireless (optional)
Enables your 802.11b/g Wireless LAN.
Chapter 1
17
Hardware Specifications and Configurations
System Board Major Chips
Item
System core logic
Controller
VIA K8N800+VIA VT8235CE
Super I/O controller
NS PC87392
Audio controller
VIA VT1612A
Video controller
NVIDIA® GeForceTM FX Go5200 for Aspire 1360 Series
NVIDIA® GeForceTM FX Go5700 for Aspire 1520 Series
Hard disk drive controller
Embedded in VT8235CE
Keyboard controller
Mitsubish LPC keyboard controller M38857
CardBus Controller
TI PCI 7420
RTC
Embedded in VT8235CE
LAN Controller/Chipset
10/100: VIA 6103L; Giga LAN: Realtek 8110SB-32
Memory Controller
Built-in CPU
Bluetooth Controller/Chipset (Does this
chipset support voice function??)
Modem Controller/Chipset
HDD Controller
Embedded in VT8235CE
ODD Controller
Embedded in VT8235CE
Parallel Port Controller
NS PC87392
USB Controller
Embedded in VT8235CE
PCMCIA Controller
TI PCI 7420
Processor
Item
CPU type
Specification
Mobile AMD Sempron processor 2600+ to 3000+ or higher (for Aspire 1360)
AMD Athlon 64 processor 3000+ to 3400+ or higher (for Aspire 1520)
CPU package uOG
uOG 754 pin
CPU core voltage
1.5V
CPU I/O voltage
High speed: 1.2V
=> for RAM 2.5V
Low speed: 1.2V
=>for Hypertransport 1.2V
BIOS
Item
18
Specification
BIOS vendor
Phoenix BIOS
BIOS Version
1.0
BIOS ROM type
Flash ROM
BIOS ROM size
512KB
BIOS package
32 Pin PLCC
Supported protocols
ACPI 2.0, SMBIOS 2.3, PCI 2.3, Boot Block, PXE 2.0, Mobile PC2001,
Hard Disk Password, INT 13h Extensions, PCI Bus Power Management
interface Specification, EI Torito-Bootable CD-ROM Format Specification
V1.0, Simple Boot Flag 1.0
BIOS password control
Set by switch, see SW1 settings on chapter 5
Chapter 1
Second Level Cache
Item
Specification
Cache controller
Built-in CPU
Cache size
128KB or 256KB for AMD Sempron CPU
1MB for AMD Athlon 64 DTR CPU
1st level cache control
Always Enabled
2nd level cache control
Always Enabled
Cache scheme control
Fixed-in write back
System Memory
Item
Specification
Memory controller
VIA K8N800
Onboard memory size
0MB
DIMM socket number
2 Sockets
Supports memory size per socket
256/512/1024MB (if available)
Supports maximum memory size
2048MB (Please confirm if 1024MB has passed the test or not)
Supports DIMM type
DDR-DRAM
Supports DIMM Speed
333 MHz
Supports DIMM voltage
2.5 V
Supports DIMM package
200-pin so-DIMM
Memory module combinations
You can install memory modules in any combinations as long as they
match the above specifications.
Memory Combinations
Slot 1
0MB
Slot 2
128MB
Total Memory
128 MB
128MB
0MB
128 MB
128MB
128MB
256 MB
256MB
0MB
256MB
0MB
256MB
256MB
256MB
128MB
384MB
128MB
256MB
384MB
256MB
256MB
512MB
0MB
512MB
512MB
512MB
128MB
640MB
256MB
512MB
768MB
128MB
512MB
640MB
512MB
256MB
768MB
256MB
128MB
384MB
512MB
512MB
1024MB
Above table lists some system memory configurations. You may combine DIMMs with various capacities to
form other combinations.
LAN Interface
Item
Chipset
Chapter 1
Specification
10/100Mbps: VIA 6103L; Giga LAN: 8110SB-32
19
LAN Interface
Item
Specification
Supports LAN protocol
10/100Mbps for Aspire 1360; 10/100/1000Mbps for Aspire 1520
LAN connector type
RJ45
LAN connector location
Rear side
PXE Version
2.0
Modem Interface
Item
Specification
Chipset
VIA VT8235CE
Fax modem data baud rate (bps)
14.4K
Data modem data baud rate (bps)
56K
Supports modem protocol
V.90/V.92MDC
Modem connector type
RJ11
Modem connector location
Rear side
.
Hard Disk Drive Interface
Item
Vendor & Model
Name
HGST Moraga
IC25N030ATMR04
HGST Moraga
IC25N040ATMR04-
HGST Moraga
IC25N060ATMR04-0
Fujitsu V-40 MHT2030AT
TOSHIBA Pluto 40G
MK4025GAS
TOSHIBA Neptune
MK6021GAS
Seagate N1 ST93015A
Fujitsu V40+ MHT2040AT
Seagate N1 ST94019A
Capacity (MB)
30000
40000
60000
Bytes per sector
512
512
512
Logical heads
16
16
16
Logical sectors
63
63
63
Logical cylinders
16383
16383
16383
Physical read/write
heads
2/Not show/2
2/Not show/2/2
3/4
Drive Format
Disks
1/Not show/1
1/Not show/1/1
2
Spindle speed (RPM)
4200RPM
4200RPM
4200RPM
Performance Specifications
Buffer size
2MB
2MB/8MB for Toshiba
2MB/8MB for HGST
Interface
ATA-5 for other vendors /ATA6 for HGST and Toshiba
ATA-5 for other vendors /ATA6 for HGST
ATA-5/ATA-6 for HGST
Data transfer rate
(disk-buffer, Mbytes/
s)
350
350
350
Data transfer, rate
(host~buffer, Mbytes/
s)
100 MB/Sec
100 MB/Sec
100MB/Sec
5 +/- 5%
5 +/- 5%
DC Power Requirements
Voltage tolerance
20
5 +/- 5%
Chapter 1
CD-ROM Interface
Items
Specification
Vendor & Model Name
QSI SCR242
Mitsumi SR244W1
Performance Specification
Brust Data Transfer rate
PIO mode 4:
16.7 MB/sec Max. (Mode 0~4)
Multi-word DMA mode 2:
16.7 MB/sec Max. (Mode 0~2)
Ultra DMA mode 2:
33.3MB/sec Max.
Access time (typ.)
QSIRandom: 90 ms
Full Stroke: 180 ms
MitsumiRandom: 100 ms
Full Stroke: 240 ms
Rotation speed
5100 rpm for QSI
5400 rpm for Mitsumi 24X CAV mode
Data Buffer Capacity
128 KB (built-in)
Interface
Compliant to ATA/ATAPI-6
Applicable disc format
QSI:
CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2, Form-1 and Mode-2 Form-2, CD-i
Ready, Video-CD (MPEG-1), Karaoke CD, Photo-CD, Enhanced CD, CD Plus, CD
Extra, i-trax CD, CD-Text, CD-R and CD-RW
Mitsumi:
CD-DA, CD-ROM (Mode 1 and Mode2) CD-ROM XA (Mode 2 Form 1 and Form2),
CD-I (Mode2 Form 1 and Form 2), CD-I Bridge (Photo CD, CD EXTRA), Enhanced
CD, CD-RW, CD-R, CD-TEXT
Loading mechanism
Drawer with soft eject and emergency eject hole
Power Requirement
Input Voltage
+5V[DC]+/-5%
DVD-ROM Interface
Item
Specification
Vendor & model name
MKE SR-8177
Performance Specification
With CD Diskette
With DVD Diskette
Transfer rate (KB/sec)
Average Sustained:
DVD-5:
CAV mode
Normal Speed (1X) 11.08 Mbits/sec
775~1800 blocks/sec
CAV mode 36.67~88.64 Mbits/sec
(10.3X to 24X)
DVD-9/DVD-R:
1550~3600kBytes/sec (Mode 1)
Normal Speed (1X) 11.08 Mbits/sec
1768~4106 kBytes/sec (Mode 2)
CAV mode 36.67~88.64 Mbits/sec
Chapter 1
21
DVD-ROM Interface
Item
Average Full Access time (typ.)
Specification
Random
DVD-5:
CAV mode 110 msec typical 150
msec average max
Random
120 msec typical
160 msec average max
Full Stroke
CAV mode 200 msec typical 260
msec average max
Full Stroke
270 msec typical
350 msec average max
DVD-9:
Random
150 msec typical
200 msec average max
Full Stroke
340 msec typical
450 msec average max
DVD-RAM (2.6G)
Random
200 msec typical
300 msec average max
Full Stroke
300 msec typical
600 msec average max
DVD-RAM (4.7G)
Random
180 msec typical
300 msec average max
Full Stroke
320 msec typical
700 msec average max
Data Buffer Capacity
512 kBytes
Interface
IDE
Applicable disc format
DVD: DVD-5, DVD-9, DVD-10, DVD-R (3.95G), DVD-RAM (2.6G), DVDRAM (4.7G)
CD: CD-Audio, CD-ROM (mode 1 and mode 2), CD-ROM XA (mode 2, form
1 and form 2), CD-I (mode 2, form 1 and form 2), CD-I Ready, CD-I Bridge,
CD-WO, CD-RW, Photo CD, Video CD, Enhanced Music CD, CD-TEXT
Loading mechanism
Soft eject (with emergency eject hole)
Power Requirement
Input Voltage
+5V[DC]+/-5%
Combo Drive Interface
Item
Vendor & model name
Specification
KME UJDA750
Performance Specification
22
Chapter 1
Combo Drive Interface
Item
Transfer rate (KB/sec)
Specification
Read Sustained:
DVD-ROM MAX 8X CAV (MAX 10800 KB/sec)
CD-ROM
MAX 24X CAV (MAX 3600 KB/sec)
CD-R
4X, 8X (CLV), Max 16X, MAX 24X (ZCLV)
Write:
CD-RW
4X (CLV)
HS-RW
4X,8X, 10X (CLV)
ATAPI Interface:
PIO mode 16.6 MB/sec :PIO Mode 4
DMA mode 16.6 MB/sec:Multi word mode 2
Ultra DMA mode 33.3MB/sec: Ultra DMA mode 2
Buffer rate
2MB
Access time
DVD-ROM 180 ms typ. (1/3 stroke)
Start up time
less than 15s
Stop time
less than 6s
Acoustic noise
less than 50 dBA
CD-ROM 130 ms typ. (1/3 stroke)
Interface
Enhanced IDE (ATAPI) compatible
Master/Slave
Set by Cable Select (By host)
PC compatible
PC2001 compatible
Applicable disc format
CD:
CD-DA, CD-ROM, CD-ROM XA, CD-R, CD-RW, PhotoCD (multiSession),
Video CD, CD-Extra(CD+), CD-text
DVD: DVD-ROM, DVD-R, DVD-RW (Ver.1.1), DVD-VIDEO, DVD-RAM
(2.6GB, 4.7GB)
Slope
15 degree (Any direction)
Dimensions, Weight
128X129X12.7mm (WXDXH)
(except protrusion)
200g+- 10g
Eject
Soft Eject (with emergency eject hole)
DVD Dual Interface
Item
Vendor & model name
Specification
Liteon DVD-Dual SDW-431S
Disc type for read/write application
Applicable Formats
CD-DA, CD-TEXT, CD ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and
Form-2, CD-I Ready, Video-CD (MPEG-1), Karaoke-CD, Photo-CD,
Enhance CD, CD extra, I-Trax CD and UDF DVD-ROM, DVD-Video, DVDAudio,
DVD-R single/multi border(s)
DVD+R single/multi session(s)
DVD-RW
DVD+RW
Applicable Media Type
CD-ROM, CD-R and CD-RW
DVD-ROM (4.7G/8.54G) single layer on single/double side (read only),
DVD-ROM dual layer (PTP/OTP) on single/double side (read only)
DVD-R (3.9G, 4.7G for General and Authoring),
DVD-RW, DVD+RW (4.7G)
DVD+R
Chapter 1
23
DVD Dual Interface
Item
Specification
Disc Diameter
12cm and 8cm
Capacity
2048 bytes/sector (DVD)
2048 bytes/block (CD Mode-1 and Mode-2 Form-1)
2336 bytes/block (Mode-2)
2328 bytes/block (Mode-2 Form-2)
Operation environment for “write/rewrite” application
Host Machine
IBM compatible PC (Pentium 166 MHz or above)
OS
MS-Windows 90/ME/2000/XP/NT 4.0
Memory
Min. 128MB required
Hard Disk
Empty Storage Capacity:100 MB or more
Average access time: 20ms or less
Disc Diameter
12cm and 8cm
Recommended Media
CD-R:
AMT, CMC, Csita, Delphi, EverMedia, Imation, LeadData(Silver-Sil),
Maxell, MCC (Bagdad), Mirage, Mitsui, MoserBaer(India), MPO, NanYa,
Plasmon, Prodisc, RAMedia, Ricoh, Ritek(JS, S, Richodye), SAST (ultra
green), SKC(Korea), TDK, TY (DX dye)
Low Speed CD-RW:
CMC, Daxon, Fornet, Gigastorage, Imation, Infodisc, LeadData, MCC,
Nanya, Princo, Prodisc, Ricoh, Ritek
High Speed CD-RW:
AMT, CMC, Infodisc, Nanya, Postech, Prodisc, Ritek, Ricoh, MCC,
SKC(Korea)
Ultra Speed CD-RW:
Daxon, Imation, Infodisc, MCC, Prodisc, Ritek
DVD+R:
BEALL, CMC, Daxon, Fuji, HP, Maxell, MCC, Memorex, OPTODISC,
PRODISC, Ricoh, RICOH, Ritek, SONY, TDK, TYUDE
DVD+RW:
CMMC, Daxon, Imation, MCC, Philips, Ricoh, Ritek, Sony
DVD-R:
BeAll, CMMC, DAXON, DVSN Fornex, GSC, Imation, LeadData, Maxell,
Mitsubishi, Nanya, Pioneer, Princo, Prodisc, Ritec, Ritek, SKC, Sony,
That’s
DVD-RW:
CMC, Mitsubishi, Princo Ritek
Mechanism
Pick-up
NA:
CD: 0.51
Focusing:
Astigmatism
Tracking:
CD: DPP
DVD: 0.65
DVD-ROM: DPD
DVD+R/RW: DPP
Wave length:
CD: 785+/- 5 nm
DVD: 650+/- 15 nm
Output power:
Read CD:
1.5 mw max@objective lens
DVD: 1.0 mw max
Write CD:
65 mw max2@objective lens
DVD: 20 mw max
24
Traverse mechanism
DC Stepping motor driven
Spindle motor
DC burshless motor
Chapter 1
DVD Dual Interface
Item
Specification
Loading mechanism
Manual load/DC brushless mortor system
Audio Interface
Item
Specification
Audio Controller
VT 1612A
Audio onboard or optional
Built-in
Mono or Stereo
Stereo
Resolution
20 bit stereo Digital to Analog converter
18 bit stereo Analog to Digital converter
Compatibility
Microsoft PC98/PC99, AC97 2.1
Mixed sound source
Line-in, CD, Video, AUX
Voice channel
8/16 bit, mono/stereo
Sampling rate
44.1 KHz
Internal microphone
Yes
Internal speaker / Quantity
Yes/2
Supports PnP DMA channel
DMA channel 0
DMA channel 1
Supports PnP IRQ
IRQ10
Video Interface
Item
Specification
Vendor & Model Name
Integrated Uni Chrome Pro IGP with upt to 64MB shared video
RAM (for Aspire 1360/1520)
NVIDIA® GeForceTM FX Go5200 (for Aspire 1360, manufacturing
option)
NVIDIA® GeForceTM FX Go5700 (for Aspire 1520, manufacturing
option)
Chip voltage
N/A
Supports ZV (Zoomed Video) port
NO
Graph interface
8X AGP (Accelerated Graphic Port) Bus
Maximum resolution (LCD)
1024 x768 (32bit colors)
Maximum resolution (CRT)
1600x1200 (32 bit colors)
VGA Display Resolution
Display device
Source image in the frame buffer
800x600
1024x768
1280x1024
1400x1050
1600x1200
800x600 LCD
Expanded
640x480
True image
Partial image
Partial image
Partial image
Partial image
1024x768 LCD
Expanded
Expanded
True image
Partial image
Partial image
Partial image
1280x1024 LCD
Expanded
Expanded
Expanded
True image
Partial image
Partial image
1400x1050 LCD
Expanded
Expanded
Expanded
Expanded
True image
Partial image
1600x1200 LCD
Expanded
Expanded
Expanded
Expanded
Centered
True image
640x480 CRT
True image
Partial image
Partial image
Partial image
Partial image
Partial image
800x600 CRT
True image
True image
Partial image
Partial image
Partial image
Partial image
1024x768 CRT
True image
True image
True image
Partial image
Partial image
Partial image
1280x1024 CRT
True image
True image
True image
True image
Partial image
Partial image
Chapter 1
25
VGA Display Resolution
Source image in the frame buffer
Display device
1600x1200 CRT
640x480
800x600
True image
True image
1024x768
True image
1280x1024
1400x1050
1600x1200
True image
True image
True image
Video Memory
Item
Specification
Fixed or upgradeable
Fixed for UMA
upgradeable for NVIDIA® GeForceTM FX Go5200/5700
Video memory size
64MB
LCD Display Resolution
8 bit
(256colors)
Resolution
16 bits
(Hi color)
24 bits
(True color)
32 bits
(True color)
640x480
Yes
Yes
Yes
Yes
720x480
Yes
Yes
Yes
Yes
800x600
Yes
Yes
Yes
Yes
848x480
Yes
Yes
Yes
Yes
1024x768
Yes
Yes
Yes
Yes
CRT Display Resolutions
8 bit
(256colors)
Resolution
16 bits
(Hi color)
24 bits
(True color)
32 bits
(True color)
640x480
Yes
Yes
Yes
Yes
720x480
Yes
Yes
Yes
Yes
800x600
Yes
Yes
Yes
Yes
848x480
Yes
Yes
Yes
Yes
1024x768
Yes
Yes
Yes
Yes
1152x864
Yes
Yes
Yes
Yes
1280x1024
Yes
Yes
Yes
Yes
1400x1050
Yes
Yes
Yes
Yes
1600x1200
Yes
Yes
Yes
Yes
Parallel Port
Item
26
Specification
Parallel port controller
NS PC87392
Number of parallel port
1
Location
Rear side
Connector type
25-pin D-type
Parallel port function control
Enable/Disable by BIOS Setup
Supports ECP/EPP
Yes (set by BIOS setup)
Optional ECP DMA channel
(in BIOS Setup)
DMA channel 1 and 3
Optional parallel port I/O address
(in BIOS Setup)
378, 278
Chapter 1
Parallel Port
Item
Specification
Optional parallel port IRQ
(in BIOS Setup)
IRQ5, IRQ7
USB Port
Item
Specification
USB Compliancy Level
1.1/2.0 support
OHCI
USB 2.0
Number of USB port
4
5V/500 mA per slot
Location
Rear side
Other Remarks
3 independent OHCI USB1.1 Host Controller and 1 EHCI USN2.0
Host Controller.
PCMCIA Port
Item
Specification
PCMCIA controller
TI PCI 7420
Supports card type
Type II, Tpye III
Number of slots
Two type II, one type III
Access location
Left side
Supports ZV (Zoomed Video) port
Yes
Supports 32 bit CardBus
Yes (IRQ17)
Keyboard
Item
Specification
Keyboard controller
Mitsubishi LPC keyboard controller M38857
Keyboard vendor & model name
Darfon/Sunrex
Total number of keypads
84-/85-/88-key
Windows keys
Yes
Internal & external keyboard work simultaneously
Yes
Battery
Item
Vendor & model name
Specification
Normal: Sanyo/Simplo; Highrate: Sanyo/Sony
Battery Type
Li-ION
Pack capacity
2000mAH
Number of battery cell
8
Package configuration
4 serial 2 parallel
Output voltage
14.4Vdc (nominal)
LCD
Item
Vendor & model name
Chapter 1
LCD 15.4" WXGA QDI LCD 15.4" WXGA AU
B154EW01
LCD 15.4" WXGA
HITACHI
27
LCD
Item
Screen Diagonal (mm)
390.1
391
391
Active Area (mm)
331.2x207.0
331.2x207.0
331.2x207.0
Display resolution (pixels)
1280x800 WXGA
1280x800 WXGA
1280x800 WXGA
Pixel Pitch
0.2588x0.2588
0.2588x0.2588
0.25875x0.25875
Pixel Arrangement
R.G.B. Vertical Stripe
R.G.B. Vertical Stripe
R.G.B. Vertical Stripe
Display Mode
Normally White
Normally White
Normally White
Typical White Luminance (cd/m2)
185
195 min (5 point
average)
185
also called Brightness
220 Typ. (5 point
average)
Luminance Uniformity
1.4 (5pts)
1.25 max. (5pts)
N/A
1.50 max. (13pts)
Contrast Ratio
400
400
200
Response Time (Optical Rise Time/Fall
Time)
5/20
18/7
30/20
Nominal Input Voltage VDD
+3.3V Typ.
+3.3V Typ.
+3.3V Typ.
Typical Power Consumption (watt)
4.38
6.5
N/A
Weight
585
580
620
Physical Size(mm)
344x222.0x6.35 max
344x222.0x6.5 max
344.5x222.5x6.5 max
Electrical Interface
1 channel LVDS
1 channel LVDS
1 channel LVDS
Support Color
262K colors (RGB 6bit data driver)
262K colors (RGB 6bit data driver)
262K colors (RGB 6bit data driver)
Horizontal: Right/Left
15/35
70/70
60/60
Vertial: Upper/Lower
45/45
60/60
35/65
0 to +50
0 to +50
0 to +50
-25 to +60
-20 to +60
-20 to +60
Viewing Angle (degree)
Temperature Range( ° C)
Operating
Storage (shipping)
AC Adapter
Item
Vendor & model name
Specification
Liteon, 135W power supply
Input Voltage
Low Range
90(min.)/137(max.)/100-127(nominal)
High Range
180(min.)/265(max.)200-240(nominal)
Input current
2.2A(max)
Nominal frequency (Hz)
50-60
Frequency variation range (Hz)
47-63
Efficiency
It should provide an efficiency of 85% minimum, when measured at maximum
load under 115Vac.
Output Requirements
DC output voltage
19V
Noise + Ripple
380mV as output voltage is 19V
Peak Load
18.5V-19.71V
Dynamic Output Characteristics
28
Turn-on delay time
5 sec (@ 115Vac)
Hold up time
5ms (@115Vac, Full load)
Chapter 1
AC Adapter
Item
Specification
Over Voltage Protection (OVP)
29V
Short circuit protection
9.5A @19V output voltage
Electrostatic discharge (ESD)
15KV (at air discharge)
8KV (at contact discharge)
Dielectric Withstand Voltage
Primary to secondary
2150VDC for 1 sec.
Ground leakage current
less than 250uA
Power Management
Power Saving Mode
Phenomenon
Standby Mode
Enter Standby Mode when
T
T
The buzzer beeps
The Sleep indicator lights up
T
All power shuts off
T
The display shuts off
T
Hard disk drive is in standby mode.
(spindle turned-off)
1.Standby/Hibernation hot-key is pressed
and system is not ready to enter Hibernation
mode.
2.System standby/ Hibernation timer expires
and system is not ready to enter Hibernation
mode.
Hibernation Mode
Enter Hibernation Mode (suspend to HDD)
when
1.Hibernation hot-key is pressed and
system is ready to enter Hibernation mode
2.System Hibernation timer expires and
system is ready to enter Hibernation mode.
Display Standby Mode
Keyboard, built-in touchpad, and an external
PS/2 pointing device are idle for a specified
period.
Hard Disk Standby Mode
Hard disk is idle within a specified period of
time.
Environmental Requirements
Item
Specification
Temperature
Operating
+5~+35 °C
Non-operating
-20~+60 °C
Humidity
Operating
10% to 95% RH, non-condensing without disktte
10% to 80% RH, non-condensing with disktte
Non-operating
20% to 80% RH, non-condensing (Unpacked)
Non-operating
20% to 90% RH, non-condensing (Storage package)
Vibration
Operating
5~250Hz 0.5Grms, 15mins per axis
Non-operating (unpacked)
1.04 Grms, 2-200Hz 15 mins per axis
Non-operating (packed)
1.04 Grms, 2-200Hz 15 mins per axis
Chapter 1
29
Mechanical Specification
Item
Dimensions
Specification
361(W) x 292.5(D) x 47.3(H)mm
Weight
3.6kg (8lbs)
I/O Ports
Two Type II or one Type III PC CardBus (PCMCIA) slot
One IEEE 1394 port
One FIR port
One RJ-11 modem jack (V.92, 56K)
One RJ-45 network jack
One DC-in jack
One parallel port (ECP/EPP)
One S-video port
One external monitor port
One microphone-in jack (3.5mm mini jack)
One headphone jack (3.5mm mini jack)
Four USB 2.0 ports
30
Drive Bays
One
Material
Plastic
Indicators
Wireless Communication, Power, Sleep, Media Activity, Battery Charge, Caps
Lock and NumLock
Switch
Power
Chapter 1
Chapter 1
31
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
PhoenixBIOS Setup Utility
. Info.
Main
CPU Type :
CPU Speed :
HDD Model Name :
HDD Serial Number :
ATAPI Model Name :
Advanced
Security
Boot
Exit
Mobile AMD Sempron (TM) Processor 2800+
1.6 GHz
HTS4244040N9AT00-(PM)
MPA201Q2G0W2YA
MATSHITADVD-RAM UJ-825S
ATAPI Serial Number None
System BIOS Ver
V1.0
VGA BIOS Ver
KBC Ver
Serial Number
90.F8.00.37
02.13.29
xxxxxxxxxxxxxxxxxxxxxx
22 Byte
Asset Tag Number
Produce Name
N/A
Aspire 1360
32 Byte
16 Byte
Manufacturer Name:
UUID:
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
16 Byte
32 Byte
F1
Help
Esc Exit
Chapter 2
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
32
Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
T
To choose a menu, use the cursor left/right keys (zx).
T
To choose a parameter, use the cursor up/down keys ( wy).
T
To change the value of a parameter, press por q.
T
A plus sign (+) indicates the item has sub-items. Press e to expand this item.
T
Press ^ while you are in any of the menu options to go to the Exit menu.
T
In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values.
This menu provides you the information of the system.
33
Chapter 2
Information
PhoenixBIOS Setup Utility
. Info.
Main
CPU Type :
CPU Speed :
HDD Model Name :
HDD Serial Number :
ATAPI Model Name :
Advanced
Security
Boot
Exit
Mobile AMD Sempron (TM) Processor 2800+
1.6 GHz
HTS4244040N9AT00-(PM)
MPA201Q2G0W2YA
MATSHITADVD-RAM UJ-825S
ATAPI Serial Number None
System BIOS Ver
V1.0
VGA BIOS Ver
KBC Ver
Serial Number
90.F8.00.37
02.13.29
xxxxxxxxxxxxxxxxxxxxxx
22 Byte
Asset Tag Number
Produce Name
N/A
Aspire 1360
32 Byte
16 Byte
Manufacturer Name:
UUID:
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
16 Byte
32 Byte
F1
Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
NOTE: The system information is subject to different models.
Parameter
CPU Type
Description
Displays the CPU type information.
CPU Speed
Displays the CPU speed.
HDD Model Name
HDD device model name information will be retrieved automatically during system boot.
HDD Serial Number
HDD device serial number information will be retrieved automatically during system boot.
ATAPI Model Name
Display the ATAPI device model name.
ATAPI Serial Number
Display the ATAPI device serial number
System BIOS Ver
Displays the system BIOS version.
VGA BIOS Ver
Displays the VGA BIOS version.
KBC Ver
Displays the keyboard controller firmware version.
Serial Number
Displays the system serial number.
Asset Tag Number
N/A
Product Name
Displays the product name.
Manufacturer Name
Displays the Acer company.
UUID Number
Displays the UUID (Universal Unique IDentifier) string = 32 bytes.
Chapter 2
34
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.
PhoenixBIOS Setup Utility
Info.
Advanced
Main
Security
Boot
Exit
Item Specific Help
System Time:
[15:56:48]
System Date:
[08/23/2004]
System Memory:
640 KB
<Tab>, <Shift-Tab>, or
<Enter> selects field.
Shows system base memory size
Extended Memory:
446MB
Shows extended memory size
Video Memory
[64 MB]
VGA memory size
Quiet Boot:
[Enabled]
Power on Display:
[Auto ]
LCD Auto Dim
Network Boot
[Enabled]
[Enabled]
F12 Boot Menu:
[Disabled]
[Enabled]
D2D Recovery
F1
Help
Esc Exit
↑↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
NOTE: The screen above is for reference only. Actual values may differ.
35
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Sets the system time. The hours are displayed
with 24-hour format.
Format: HH:MM:SS
(hour:minute:second) System Time
System Date
Sets the system date.
Format MM/DD/YYYY (month/day/
year)
System Date
System Memory
This field reports the memory size of the system.
Memory size is fixed to 640MB
Extended Memory
This field reports the memory size of the
extended memory in the system.
Extended Memory size=Total memory size-1MB
VGA Memory
Shows the VGA memory size. VGA Memory
size=64/128MB
Fast Boot
Determines if Customer Logo will be displayed or
not; shows Summary Screen is disabled or
enabled.
Option: Enabled or Disabled
Enabled: Customer Logo is displayed, and
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and
Summary Screen is enabled.
Power on display
Auto: During power process, the system will
detect if any display device is connected on
external video port. If any external display device
is connected, the power on display will be in CRT
(or projector) only mode. Otherwise it will be in
LCD only mode.
Option: Auto or Both
Both: Simultaneously enable both the integrated
LCD screen and the system’s external video port
(for an external CRT or projector).
LCD Auto Dim
Determines if the system will automatically dim
the LCD brightness in order to save power when
AC is not present.
Option: Enabled or Disabled
The system will support an automatic dimming of
the LCD backlight when the AC power is NOT
available (running on battery power).
Network Boot
Enables, disables the system boot from LAN
(remote server).
Option: Enabled or Disabled
F12 Boot Menu
Enables, disables Boot Menu during POST.
Option: Disabled or Enabled
D2D Recovery
Enables or disables Hard Disk to Hard Disk
system Recovery by pressing Fn+F10 key during
POST.
Option: Enabled or Disabled
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
Chapter 2
36
Advanced
The Advanced menu screen contains parameters involving your hardware devices. It also provides advanced
settings of the system.
PhoenixBIOS Setup Utility
Info.
Main
Infrared Port (FIR)
Base I/O address:
Interrupt:
DMA channel:
Advanced
Security
[Auto]
[ECP]
[378]
[IRQ 7]
[DMA 3]
Infrared Port (FIR):
[Enabled]
Exit
Item Specific Help
[Enabled]
[2F8]
[IRQ 3]
[DMA 1]
Parallel port:
Mode:
Base I/O address:
Interrupt:
DMA channel:
Boot
Configure Infrared Port
using options:
[Disable]
No configuration
[Enabled]
User configuration
[Auto]
BIOS or OS chooses
configuration
(OS Controlled)
Displayed when controlled
by OS
F1
Help
Esc Exit
↑ ↓
← →
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
The table below describes the parameters in the screen. Settings in boldface are the default and suggested
parameter settings.
.
Parameter
37
Description
Options
Infrared Port
Enables, disables or auto detects the infrared port.
Enabled/Disabled/Auto
Base I/O address
Sets the I/O address of the infrared port.
2F8/3F8/3E8/2E8
Interrupt
Sets the interrupt request of the parallel port.
IRQ3/IRQ4
DMA channel
Sets a DMA channel for the infrared port.
DMA/DMA3
Parallel Port
Enables, disables or auto detects the parallel port.
Enabled/Disabled/Auto
Mode
Sets the operation mode of the parallel port.
ECP, EPP, Output only or Bidirectional
Base I/O address
Sets the I/O address of the parallel port.
378/278
Interrupt
Sets the interrupt request of the parallel port.
IRQ7/IRQ5
Chapter 2
Parameter
Description
Options
DMA channel
Sets a DMA channel for the printer to operate in
ECP mode. This parameter is enabled only if Mode
is set to ECP.
DMA3/DMA1
Legacy USB Support
Enables, disables USB interface devices support.
(Enable for use with a non-USB aware Operating
System such as DOS or UNIX).
Option: Disabled or Enabled
Chapter 2
38
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
Info.
Main
PhoenixBIOS Setup Utility
Security
Advanced
Boot
Exit
Item Specific Help
User Password is :
Clear
Supervisor Password is :
Clear
Set User Password
Set Supervisor Password
[Enter]
[Enter]
controls accesses of the
whole setup utility.
Primary HardDisk Security
[Disabled]
It can be used to
boot up when Password
on boot is enabled.
Password on Boot
[Disabled]
Supervisor Password
F1
Help
Esc Exit
39
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
User Password is
Shows the setting of the user password.
Clear or Set
Supervisor Password is
Shows the setting of the Supervisor password
Clear or Set
Set User Password
Press Enter to set the user password. When
set, this password protects the BIOS Setup
Utility from unauthorized access.
Set Supervisor Password
Press Enter to set the supervisor password.
When set, this password protects the BIOS
Setup Utility from unauthorized access.
Primary Harddisk Security
This feature is available to user when
Supervisor password is set. Password can be
written on HDD only when Supervisor
password or user password is set and
password on HDD is set to enabled.
Supervisor Password is written to HDD only
when Supervisor password is being set. User
password is written to HDD when both
passwords are set. When both Supervisor and
user password are present, both passwords
can unlock the HDD.
Disabled or Enabled
Password on Boot
Defines whether a password is required or not
while the events defined in this group
happened. The following sub-options are all
requires the Supervisor password for changes
and should be grayed out if the user password
was used to enter setup.
Disabled or Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.
Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:
2.
Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.
4.
Press e.
After setting the password, the computer sets the User Password parameter to “Set”.
If desired, you can opt to enable the Password on boot parameter.
5.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2
40
Removing a Password
Follow these steps:
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Press e twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.
If desired, you can enable the Password on boot parameter.
6.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses u.
41
Chapter 2
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
Chapter 2
42
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Boot
Exit
Item Specific Help
+Hard Drive
Use <↑> or <↓> to select a
device, then press <F6> to
move it up the list, or <F5>
move it down the list.
Press <ESC> to escape the
menu
Floppy Drive
CD-ROM/DVD Drive
Network Boot
F1
Help
Esc Exit
43
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Exit
Boot
Item Specific Help
Exit Saving Changes
Exit System Setup and save
your changes to CMOS.
Exit Dicarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1
Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS.
Exit Discarding Changes
Exit utility without saving setup data to CMOS.
Load Setup Default
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
44
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
T
New versions of system programs
T
New features or options
T
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Phlash.
45
1.
Prepare a bootable diskette.
2.
Copy the Phlash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The Phlash utility has auto-execution function.
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
T
Flat-bladed screw driver
T
Phillips screw driver
T
Tweezers
T
Plastic Flat-bladed screw driver
Hexed Screw Driver
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
T
NOTE: This chapter has been revised from previous model (TravelMate 240/250). Please refer to the
disassembling procedures instead of the images. Some of the images below contain the parts used in
TravelMate 240/250, but not in Aspire 1360/1520.
Chapter 3
46
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
47
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Start
Battery
*2
HDD Module
*2
DIMM Cover
Modem Cover
Hinge Caps
G*2
D*2
HDD
HDD Holder
Wireless LAN
Board
Memory
J*2
Modem Board
Middle Cover
*2
F*6
RTC Battery
Keyboard
LCD Module
Launch Board
J*3
J*5
F*10
D*4
Second Fan
*4
Lower Case
Assembly
Upper Case
Assembly
J*3
Second Fan
Bracket
J*2
D*4
Wireless LAN
Antenna
FDD Module
F*1
J*4
ODD Module
Thermal
Module
*1
ODD Support
Bracket
HDD Bracket
CPU Heatsink
Plate
Touchpad
Cover
CPU
J*7
VGA Thermal
Plate
Touchpad
Button Pad
D*2
*4
ODD Bracket
ODD
Main Board
D*2
DC Board
Touchpad
Scroll Key
Touchpad
D*4
PCMCIA Slot
Touchpad
Cable
Upper Case
*2
Speaker Set
Chapter 3
48
LCD Module
4 LCD
Cushions
E*4
LCD Bezel
L*1
Inverter
L*4
LCD
LCD Panel
H*8 for 14.1"
H*6 for 15.0"
LCD Coaxial
Cable
LCD Brackets
Screw List
Item
A
49
Description
SCREW MAC FLAT M2.5*L4 NI NYLOK
(86.00123.630)
B
SCREW M2.0*L10 NYLOK(86.9A352.100)
C
SCREW M2*3 NYLON 1JMCPC420325(86.9A352.3R0)
D
SCREW M2.5X6(86.9A353.6R0)
E
SCREW M3x4 (86.9A524.4R0)
F
SCREW M2X2.0 (86.9A552.2R0)
G
SCREW WAFER NYLOK NI 2ML3 (86.9A552.3R0)
H
SCRW M2*4 WAFER NI (86.9A552.4R0)
I
SCRW M2.5*3 WAFER NI (86.9A553.3R0)
J
SCREW M2.5*4L NI (86.9A553.4R0)
Chapter 3
Removing the Battery
1.
To remove the battery, push the battery release latch.
2.
Then slide the battery out from the machine.
Chapter 3
50
Removing the Memory Module
51
1.
See “Removing the Battery” on page 50.
2.
To remove the memory module from the machine, first remove the two screws holding the dimm cover.
3.
Remove the dimm cover.
4.
Pop up the memory.
5.
Then remove the memory.
Chapter 3
Removing the Wireless LAN Board and the Modem Board
1.
See “Removing the Battery” on page 50.
2.
To remove the wireless LAN board, first remove the two screws holding the modem cover.
3.
Remove the modem cover from the machine.
4.
Disconnect the wireless antennae.
5.
Pop out the wireless LAN board.
6.
To remove the modem board, first remove the two screws fastening the modem board.
7.
Detach the modem board and disconnect the modem cable carefully, then remove the modem board.
Chapter 3
52
Removing the Hard Disk Drive Module
1.
See “Removing the Battery” on page 50.
2.
To remove the hard disk drive, pull the hard disk dirve carefully.
3.
Then take the hard disk drive out of the main unit.
Disassembling the Hard Disk Drive Module
53
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Hard Disk Drive Module” on page 53.
3.
Remove the two screws that fasten the HDD holder.
4.
Detach the hard disk drive from the HDD holder.
Chapter 3
Removing the LCD Module
Removing the Middle Cover
1.
See “Removing the Battery” on page 50.
2.
To remove the middle cover, first use a plastic flat screwdriver to detach the right hinge cap. If you do not
have a plastic flat screwdriver, you can simply detach the right hinge cover as the image shows. There is
no screw fastening the right hinge cap to the main unit. Please just detach it.
3.
Detach the left hinge cap.
4.
Remove the two screws holding the middle cover.
5.
Then detach the middle cover from the machine.
6.
Turn over the middle cover then disconnect the launch board cable. Then remove the middle cover.
Removing the Launch Board
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
Remove the two screws that secure the launch board to the middle cover. Then detach the launch board
from the middle cover.
Chapter 3
54
Removing the LCD Module
55
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Launch Board” on page 54.
4.
Remove the screw that fastens the LCD coaxial cable and disconnect the cable. Then disconnect the
LCD inverter cable.Then pull out the wireless antennae from the main unit carefully.
5.
Remove the four screws holding the LCD hinge; two on the right and two on the left.Remove the four
screws holding the LCD hinge; two on the right and two on the left.
6.
Remove the two screws on the bottom; one on the right and the other on the left.
7.
Then you can remove the entire LCD module from the main unit.
Chapter 3
Chapter 3
56
Disassembling the LCD Module
Removing the LCD Bezel
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Launch Board” on page 54.
4.
See “Removing the LCD Module” on page 55.
5.
Use plastic tweezers to remove the four screw pads, and then remove the four screws that fasten the LCD
bezel.
6.
Snap off the bezel carefully, and then remove the LCD bezel from the LCD module.
Removing the Inverter Board (15” LCD)
57
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Launch Board” on page 54.
4.
See “Removing the LCD Module” on page 55.
5.
See “Removing the LCD Bezel” on page 57.
6.
To remove the inverter board, first remove one screw from the inverter board.
7.
Disconnect the LCD power cable then disconnect the inverter cable from the inverter board.
Chapter 3
NOTE: Please arrange the LCD inverter cable well to the LCD panel as the picture below shows when you
reassemble the LCD module.
Removing the 15” TFT LCD
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Launch Board” on page 54.
4.
See “Removing the LCD Module” on page 55.
5.
See “Removing the LCD Bezel” on page 57.
6.
See “Removing the Inverter Board (15” LCD)” on page 57.
7.
To remove the LCD, first remove the four screws that secure the LCD hinges.
8.
Then take the LCD out of the LCD panel.
Chapter 3
58
Removing the LCD Brackets
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Launch Board” on page 54.
4.
See “Removing the LCD Module” on page 55.
5.
See “Removing the LCD Bezel” on page 57.
6.
See “Removing the Inverter Board (15” LCD)” on page 57.
7.
See “Removing the 15” TFT LCD” on page 58.
8.
Remove the four screws holding the right LCD bracket.Then remove the right bracket.
9.
Remove the four screws holding the left LCD bracket. Then remove the left bracket..
Removing the LCD Coaxial Cable
59
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Launch Board” on page 54.
4.
See “Removing the LCD Module” on page 55.
5.
See “Removing the LCD Bezel” on page 57.
6.
See “Removing the Inverter Board (15” LCD)” on page 57.
7.
See “Removing the 15” TFT LCD” on page 58.
8.
Tear off the mylar fastening the LCD coaxial cable, then disconnect the coaxial cable.
Chapter 3
Removing the LCD Hinges
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Launch Board” on page 54.
4.
See “Removing the LCD Module” on page 55.
5.
See “Removing the LCD Bezel” on page 57.
6.
See “Removing the Inverter Board (15” LCD)” on page 57.
7.
See “Removing the 15” TFT LCD” on page 58.
8.
Remove the screw holding the right hinge, then remove the right hinge.
9.
Remove the screw holding the left hinge, then remove the left hinge.
Chapter 3
60
Disassembling the Main Unit
Removing the Keyboard
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
Detach the keyboard from the main unit. Then turn over the keyboard.
4.
Disconnect the keyboard cable and remove the keyboard.
.
Removing the RTC Battery
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
Disconnect the RTC battery cable then remove it.
Removing the Middle Cover Hook /Fan
61
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
Remove the two screws holding the middle cover hook, then remove it.
Chapter 3
Removing the Thermal Module
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the Middle Cover Hook /Fan” on page 61.
5.
Disconnect the fan cable then remove the four screws fastening the thermal module.
6.
Then remove the thermal module.
Removing the Processor
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the RTC Battery” on page 61.
5.
See “Removing the Middle Cover Hook /Fan” on page 61.
6.
See “Removing the Thermal Module” on page 62.
7.
Lift up the CPU socket lever. Then remove the CPU. Remember to press down the lever as the video
shows after you remove the CPU.
Installing the Processor
1.
See “Removing the Battery” on page 50.
Chapter 3
62
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the RTC Battery” on page 61.
5.
See “Removing the Middle Cover Hook /Fan” on page 61.
6.
See “Removing the Thermal Module” on page 62.
7.
Lift up the CPU lever, then place the CPU back to the CPU socket. Please remember to press the CPU
lever after you put the CPU back to the socket.
Removing the Upper Case Assemly
63
1.
See “Removing the Keyboard” on page 61.
2.
Disconnect the touchpad cable.
3.
Remove the 5 screws that secure the upper case to the lower case. Then turn over the main unit and
remove the 15 screws holding the lower case to the upper case.
4.
Then take the upper case assembly off the main unit.
Chapter 3
Removing the Touchpad Board
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the Upper Case Assemly” on page 63.
5.
To detach the touch pad board, first disconnect the touch pad cable from the touch pad board with a
plastic tweezers.Then release the touchpad cover lock on the back as the picture shows.
6.
Remove the touchpad cover, the remove the touchpad button pad. Finally remove the touchpad board
from the upper case.
Removing the Touchpad Cable
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the LCD Module” on page 55.
4.
See “Removing the Keyboard” on page 61.
5.
See “Removing the Upper Case Assemly” on page 63.
6.
See “Removing the Touchpad Board” on page 64.
7.
Remove the touchpad scroll key then remove the touchpad cable.
Removing the VGA Thermal Plate
1.
See “Removing the Battery” on page 50.
Chapter 3
64
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the Middle Cover Hook /Fan” on page 61.
5.
See “Removing the Thermal Module” on page 62.
6.
Remove the seven screws holding the VGA thermal plate then remove it.
Removing the CPU Heatsink Plate
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the Middle Cover Hook /Fan” on page 61.
5.
See “Removing the Thermal Module” on page 62.
6.
Remove two screws that fasten the CPU heatsink plate then remove it.
Removing the Second Fan Bracket
65
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the LCD Module” on page 55.
4.
See “Removing the RTC Battery” on page 61.
5.
See “Removing the Middle Cover Hook /Fan” on page 61.
6.
See “Removing the Thermal Module” on page 62.
7.
Remove the four screws that fasten the second fan bracket then remove the bracket.
Chapter 3
Removing the ODD Module(1)
1.
See “Removing the Battery” on page 50.
2.
Remove the screw that fastens the ODD bracket on the bottom. Push the ODD module at the point the
red arrow indicates hard.Then remove the ODD module from the lower case.
NOTE: If you need to replace the ODD module only, you can remove the ODD module as the steps above.
Removing the ODD Module(2)
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the Upper Case Assemly” on page 63.
5.
See “Removing the Thermal Module” on page 62.
6.
See “Removing the VGA Thermal Plate” on page 64.
7.
Push the ODD module outwards then take the ODD out of the support bracket. Remove the screw that
fastens the ODD support bracket then remove it.
Removing the HDD Bracket
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
Chapter 3
66
4.
See “Removing the Upper Case Assemly” on page 63.
5.
Remove the four screws holding the HDD bracket, then remove the HDD bracket.
Removing the Main Board
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the Upper Case Assemly” on page 63.
5.
See “Removing the Middle Cover Hook /Fan” on page 61.
6.
See “Removing the Thermal Module” on page 62.
7.
See “Removing the VGA Thermal Plate” on page 64.
8.
See “Removing the CPU Heatsink Plate” on page 65.
9.
See “Removing the Second Fan Bracket” on page 65.
10. See “Removing the ODD Module(2)” on page 66.
11. See “Removing the HDD Bracket” on page 66.
12. Disconnect the launch board cable. Tear off the tape that fastens the speaker set cable. Then disconnect
the speaker set cable.
.
13. Remove the two screws holding the main board as the picture shows. Remove another two screws that
fasten the main board. Then detach the main board from the lower case carefully.
67
Chapter 3
Removing the DC Board
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the Upper Case Assemly” on page 63.
5.
See “Removing the Middle Cover Hook /Fan” on page 61.
6.
See “Removing the Thermal Module” on page 62.
7.
See “Removing the VGA Thermal Plate” on page 64.
8.
See “Removing the CPU Heatsink Plate” on page 65.
9.
See “Removing the Second Fan Bracket” on page 65.
10. See “Removing the ODD Module(2)” on page 66.
11. See “Removing the HDD Bracket” on page 66.
12. See “Removing the Main Board” on page 67.
13. Remove the two screws that fasten the DC board. Then detach the DC board from the lower case.
Removing the I/O Port Bracket
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the Upper Case Assemly” on page 63.
5.
See “Removing the Middle Cover Hook /Fan” on page 61.
6.
See “Removing the Thermal Module” on page 62.
7.
See “Removing the VGA Thermal Plate” on page 64.
8.
See “Removing the CPU Heatsink Plate” on page 65.
9.
See “Removing the Second Fan Bracket” on page 65.
10. See “Removing the ODD Module(2)” on page 66.
11. See “Removing the HDD Bracket” on page 66.
12. See “Removing the Main Board” on page 67.
13. Remove the four hex screws to detach the I/O port bracket from the main board.
Chapter 3
68
Removing the PCMCIA Slot
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the Upper Case Assemly” on page 63.
5.
See “Removing the Middle Cover Hook /Fan” on page 61.
6.
See “Removing the Thermal Module” on page 62.
7.
See “Removing the VGA Thermal Plate” on page 64.
8.
See “Removing the CPU Heatsink Plate” on page 65.
9.
See “Removing the Second Fan Bracket” on page 65.
10. See “Removing the ODD Module(2)” on page 66.
11. See “Removing the HDD Bracket” on page 66.
12. See “Removing the Main Board” on page 67.
13. Remove the four screws that secure the PCMCIA slot, then remove the PCMCIA slot from the lower case.
Removing the Speaker Set
69
1.
See “Removing the Battery” on page 50.
2.
See “Removing the Middle Cover” on page 54.
3.
See “Removing the Keyboard” on page 61.
4.
See “Removing the Upper Case Assemly” on page 63.
5.
See “Removing the Middle Cover Hook /Fan” on page 61.
6.
See “Removing the Thermal Module” on page 62.
7.
See “Removing the VGA Thermal Plate” on page 64.
8.
See “Removing the CPU Heatsink Plate” on page 65.
9.
See “Removing the Second Fan Bracket” on page 65.
Chapter 3
10. See “Removing the ODD Module(2)” on page 66.
11. See “Removing the HDD Bracket” on page 66.
12. See “Removing the Main Board” on page 67.
13. See “Removing the DC Board” on page 68.
14. Tear off the tape fastening the speaker set cable. Then remove the four screws that secure the speaker
set. Remove the speaker set from the lower case.
Chapter 3
70
System Upgrade Procedure
Base Unit to Wireless Unit
1.
Turn out the two screws fastening the modem cover then open the cover.
2.
Connect the wirless antennae.
3.
Insert the wireless LAN board to the wireless socket on the main board.
4.
Close the modem cover and fasten the cover with the two screws.
NOTE: You must connect the wireless antennae before you insert the wireless LAN board to the socket. If you
insert the wireless LAN card first, the pressure you press to fasten the wireless antennae may damage
the main board.
71
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1.
Obtain the failing symptoms in as much detail as possible.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power failure. (The power indicator does not go
on or stay on.)
“Power System Check” on page 74.
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error Message” on
page 77
“Undetermined Problems” on page 89
POST detects an error and displayed messages
on screen.
“Error Message List” on page 78
Other symptoms (i.e. LCD display problems or
others).
“Power-On Self-Test (POST) Error Message” on
page 77
Symptoms cannot be re-created (intermittent
problems).
Use the customer-reported symptoms and go to
“Power-On Self-Test (POST) Error Message” on
page 77
“Intermittent Problems” on page 88
“Undetermined Problems” on page 89
Chapter 4
72
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device.
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if FDD Test is passed as the program runs to FDD Test.
3.
Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.
Reconnect the external diskette drive/DVD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.
Reconnect the external diskette drive/CD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
73
T
Numeric keypad
T
External keyboard
Chapter 4
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.
Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.
Go to the diagnostic memory in the test items.
3.
Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
Chapter 4
T
“Check the Power Adapter” on page 75
T
“Check the Battery Pack” on page 76
74
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure
Pin 1: +19 to +20.5V
Pin 2: 0V, Ground
1.
If the voltage is not correct, replace the power adapter.
2.
If the voltage is within the range, do the following:
T
Replace the System board.
T
If the problem is not corrected, see “Undetermined Problems” on page 89.
T
If the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not always indicate a defect.
75
3.
If the power-on indicator does not light up, check the power cord of the power adapter for correct
continuity and installation.
4.
If the operational charge does not work, see “Check the Battery Pack” on page 76.
Chapter 4
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Management in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the
following figure
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the touchpad cables.
2.
Replace the touchpad.
3.
Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
Chapter 4
76
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 89.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
77
Chapter 4
Index of Error Messages
Error Code List
Error Codes
006
Error Messages
Equipment Configuration Error
Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
(THe causes will be shown before “Equipment Configuration
Error”)
010
Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)
070
Real Time Clock Error
071
CMOS Battery Bad
072
CMOS Checksum Error
110
System disabled.
Incorrect password is specified.
<No error code>
Battery critical LOW
In this situation BIOS will issue 4 short beeps then shut down
system, no message will show.
<No error code>
Thermal critical High
In this situation BIOS will shut down system, not show message.
Error Message List
Error Messages
Failure Fixed Disk
FRU/Action in Sequence
Reconnect hard disk drive connector.
“Load Default Settings” in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key
see “Keyboard or Auxiliary Input Device Check” on page 73.
Keyboard error
see “Keyboard or Auxiliary Input Device Check” on page 73.
Keyboard Controller Failed
see “Keyboard or Auxiliary Input Device Check” on page 73.
Keyboard locked - Unlock key switch
Unlock external keyboard
Monitor type does not match CMOS - Run Setup
Run “Load Default Settings” in BIOS Setup Utility.
Shadow RAM Failed at offset: nnnn
BIOS ROM
System board
System RAM Failed at offset: nnnn
DIMM
System board
Extended RAM Failed at offset: nnnn
DIMM
System battery is dead - Replace and run Setup
Replace RTC battery and Run BIOS Setup Utility to reconfigure
system time, then reboot system.
System CMOS checksum bad - Default
configuration used
RTC battery
System timer error
RTC battery
System board
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Chapter 4
78
Error Message List
Error Messages
Real time clock error
FRU/Action in Sequence
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Previous boot incomplete - Default configuration
used
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Memory size found by POST differed from
CMOS
Run “Load Default Settings” in BIOS Setup Utility.
DIMM
System board
Diskette drive A error
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
See “External Diskette Drive Check” on page 73.
Incorrect Drive A type - run SETUP
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
System cache error - Cache disabled
System board
CPU ID:
System board
DMA Test Failed
DIMM
System board
Software NMI Failed
DIMM
System board
Fail-Safe Timer NMI Failed
DIMM
System board
Device Address Conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Failing Bits: nnnn
DIMM
BIOS ROM
System board
Fixed Disk n
None
Invalid System Configuration Data
BIOS ROM
System board
I/O device IRQ conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Operating system not found
Enter Setup and see if fixed disk and drive A: are properly identified.
Diskette drive
Hard disk drive
System board
79
Chapter 4
Error Message List
No beep Error Messages
No beep, power-on indicator turns off and LCD is
blank.
FRU/Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 74.
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
LED board.
System board.
No beep, power-on indicator turns on and LCD is
blank.
Power source (battery pack and power adapter). See “Power
System Check” on page 74.
Reconnect the LCD connector
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator turns on and LCD is
blank. But you can see POST on an external
CRT.
Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator turns on and a
blinking cursor shown on LCD during POST.
No beep during POST but system runs correctly.
Ensure every connector is connected tightly and correctly.
System board
Speaker
System board
Chapter 4
80
POST Code
Code
Beeps
02h
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST
values
12h
Restore CPU control word during warm boot
13h
Initialize PCI Bus Mastering devices
14h
16h
Initialize keyboard controller
1-2-2-3
BIOS ROM checksum
17h
Initialize cache before memory autosize
18h
8254 timer initialization
1Ah
8237 DMA controller initialization
1Ch
Reset Programmable Interrupt Controller
20h
1-3-1-1
Test DRAM refresh
22h
1-3-1-3
Test 8742 Keyboard Controller
24h
Set ES segment register to 4 GB
26h
Enable A20 line
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 215 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low byte of
memory bus
2Fh
30h
81
POST Routine Description
Enable cache before system BIOS shadow
1-4-1-1
RAM failure on data bits xxxx of high byte of
memory bus
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
3Ch
Advanced configuration of chipset registers
3Dh
Load alternate registers with CMOS values
42h
Initialize interrupt vectors
45h
POST device initialization
Chapter 4
Code
46h
Beeps
2-1-2-3
48h
POST Routine Description
Check ROM copyright notice
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
58h
Set key click if enabled
2-2-3-1
Test for unexpected interrupts
59h
Initialize POST display service
5Ah
Display prompt “Press F2 to enter SETUP”
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to User Patch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode (SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB
recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports
87h
Configure Motherboard Configurable Devices
(optional)
88h
Initialize BIOS Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
8Bh
Test and initialize PS/2 mouse
Chapter 4
82
Code
Beeps
8Ch
Initialize floppy controller
8Fh
Determine number of ATA drives (optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
98h
Fixup Multi Processor table
1-2
Search for option ROMs. One long, two short
beeps on checksum failure.
99h
Check for SMART drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
B2h
POST done- prepare to boot operating system
B4h
83
POST Routine Description
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
B9h
Prepare Boot
BAh
Initialize DMI parameters
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
Chapter 4
Code
Beeps
D2h
POST Routine Description
Unknown interrupt
Code
Beeps
For Boot Block in Flash ROM
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize the system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
F4h
Initialize System Management Mode
1
Output one beep before boot
F5h
Boot to Mini DOS
F6h
Clear Huge Segment
F7h
Boot to Full DOS
Chapter 4
84
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
LCD backlight doesn't work
Action in Sequence
LCD is too dark
Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.
LCD brightness cannot be adjusted
Reconnect the LCD connectors.
LCD contrast cannot be adjusted
Keyboard (if contrast and brightness function key doesn't work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Reconnect the LCD connector
Missing pels in characters
LCD inverter ID
Abnormal screen
LCD cable
Wrong color displayed
LCD inverter
LCD
System board
LCD has extra horizontal or vertical lines
displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms
Symptom / Error
Indicator incorrectly remains off or on, but system
runs correctly
Action in Sequence
Reconnect the inverter board
Inverter board
System board
Power-Related Symptoms
Symptom / Error
Power shuts down during operation
Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 74.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 74.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-off.
Power source (battery pack and power adapter). See “Power
System Check” on page 74.
Hold and press the power switch for more than 4 seconds.
System board
85
Chapter 4
Power-Related Symptoms
Symptom / Error
Battery can’t be charged
Action in Sequence
See “Check the Battery Pack” on page 76.
Battery pack
System board
PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)
Action in Sequence
PCMCIA slot assembly
System board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings, then
reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom / Error
Action in Sequence
In Windows, multimedia programs, no sound
comes from the computer.
Audio driver
Internal speakers make noise or emit no sound.
Speaker
Speaker
System board
System board
Power Management-Related Symptoms
Symptom / Error
The system will not enter hibernation
Action in Sequence
Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system doesn't enter hibernation mode and
four short beeps every minute.
See “Hibernation Mode” on page 29.
Press Fn+oand see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system doesn’t enter standby mode after
closing the LCD
See “Hibernation Mode” on page 29.
LCD cover switch
System board
The system doesn't resume from hibernation
mode.
See “Hibernation Mode” on page 29.
Hard disk connection board
Hard disk drive
System board
The system doesn't resume from standby mode
after opening the LCD.
See “Hibernation Mode” on page 29.
LCD cover switch
System board
Chapter 4
86
Power Management-Related Symptoms
Symptom / Error
Battery fuel gauge in Windows doesn’t go higher
than 90%.
Action in Sequence
Remove battery pack and let it cool for 2 hours.
Refresh battery (continue use battery until power off, then charge
battery).
Battery pack
System board
System hangs intermittently.
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Peripheral-Related Symptoms
Symptom / Error
Action in Sequence
System configuration does not match the
installed devices.
Enter BIOS Setup Utility to execute “Load Default Settings”, then
reboot system.
External display does not work correctly.
Press Fn+F5, LCD/CRT/Both display switching
Reconnect hard disk/CD-ROM/diskette drives.
System board
USB does not work correctly
System board
Print problems.
Ensure the “Parallel Port” in the “Onboard Devices Configuration” of
BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port device problems.
Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup
Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Action in Sequence
Modem phone port
modem combo board
System board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 89.
87
Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
88
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 74):
89
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
Printer, mouse, and other external devices
T
Battery pack
T
Hard disk drive
T
DIMM
T
CD-ROM/Diskette drive Module
T
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
T
System board
T
LCD assembly
Chapter 4
How to Build NAPP Master Hard Disc Drive
CD to Disk Recovery
1.
Prepare NAPP CD, Recovery CD and System CD.
2.
Put NAPP CD into the optical drive. Then boot up the system.
3.
The system will ask you if you want to build NAPP Master HDD. Please press any key to continue.
4.
NAPP CD will start to preload the system, please click [Y].
5.
Select CD to Disk Revocery.
Chapter 4
90
6.
Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have
to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till
you finish all Recovery CDs.
After you place the Recovery CD to the optical drive, you will see the display below.
91
Chapter 4
7.
Then insert the System CD to the optical drive.
8.
You will see the screen displaying “PASS” when the system has buit NAPP Master hard disc drive.
Chapter 4
92
Disk to Disk Recovery
93
1.
Prepare NAPP CD, Recovery CD and System CD.
2.
Put NAPP CD into the optical drive. Then boot up the system.
3.
The system will ask you if you want to build NAPP Master HDD. Please press any key to continue.
4.
NAPP CD will start to preload the system, please click [Y].
Chapter 4
5. Select Disk to Disk Recovery. Then choose Single Language or Multi-Languages Recovery.
NOTE: For Multi-Languages Recovery, not more than five languages could be loaded to the system.
6.
Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have
to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till
you finish all Recovery CDs.
Chapter 4
94
After you place the Recovery CD to the optical drive, you will see the display below.
7.
95
Then insert the System CD to the optical drive.
Chapter 4
8.
You will see the screen displaying “PASS” when the system has buit NAPP Master hard disc drive.
Chapter 4
96
97
Chapter 4
Chapter 5
Jumper and Connector Locations
Top View
1
LIN1
Line-in Port
2
LOUT
Line-out Port
16
U16
North Bridge
3
JK1
RJ45+RJ11
17
FAN1
Fan Connector
4
INV1
LCD Inverter Cable Connector
18
Note: There is no 18 on this main board.
5
CN1
USB Port
19
TPAD1
Touchpad Cable Connector
6
CN2
USB Port
20
HDD1
HDD Connector
7
CN3
USB Port
21
KB1
Keyboard Connector
8
CN4
USB Port
22
SPK1
Speaker Cable Connector
9
CRT1
VGA Port
23
IDE1
Optical Drive Connector
10
TV1
S-Video Port
24
U26
South Bridge
11
LCD1
LCD Coaxial Cable Connector
25
CN9
RTC Battery Connector
12
PRT1
Parallel Port
26
CN8
Launch Board Cable Connector
13
DCIN1
DC-in Port
27
SW1 (Please see Chapter 5 for its settings)
14
CN6
LCD Lid Switch
28
SKT1
Chapter 5
15
U11
CPU Socket
PCMCIA Slot
98
Bottom View
1
CN11
Wireless LAN Card Connector
5
U93
FIR Port
2
CN12
Modem Board Connector
6
DM1
DIMM Socket 1
3
CN10
Modem Cable Connector
7
DM2
DIMM Socket 2
4
SKT2
IEEE 1394 Port
8
BAT1
DC Charger Board Connector
SW Settings
SW1-8
Chkpw
SW2-7
ON
X
X
ON
SW3-6
Enable
Bootblock
Enable
99
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 1360/1520.
Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on
the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use
the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
100
Aspire 1360/1520 Exploded Diagram
101
Chapter 6
Aspire 1360
Picture
No.
Partname And Description
Part Number
Adapter
N/S
ADAPTER 19V 90W 3PIN LITEON PA1900-05QA
TBD
N/S
ADAPTER 19V 90W 3PIN DELTA ADP90SB
TBD
N/S
RTC BATTERY LONGTRUM
23.T30V1.001
18
BATTERY MODULE LI 8CELL
2000MAH SANYO
6M.A36V1.001
N/S
BATTERY LI 8CELL 2000MAH SANYO
BTP-60A1
BT.T3003.001
N/S
BATTERY LI 8CELL SIMPLO BTP-58A1 BT.T3007.003
Battery
CASE/COVER/BRACKET ASSEMBLY
BATTERY COVER
42.A30V1.001
(The cover should be silver not black)
Boards
Chapter 6
VGA BOARD NV36-64M(DIP)
TBD
DC-DC CHARGER BOARD
55.T30V1.001
102
Aspire 1360
Picture
No.
Partname And Description
Part Number
WIRELESS LAN BOARD 802.11BG
FOXCONN
54.A36V1.001
MODEM BOARD AMBIT
T60M283.10(01)
54.09011.544
MODEM/BLUETOOTH BOARD AMBIT
T60M665.00
54.09061.001
LAUNCH BOARD
55.T30V1.002
Cables
POWER CORD 10A 125V US
27.01518.311
COVER SWITCH CABLE
50.A30V1.004
LAUNCH BOARD CABLE
50.T30V1.011
MODEM CABLE 2PIN 2CONNECTOR
55MM
50.41T11.002
MODEM COVER W/SCREWS
42.A20V1.001
HINGE CAP RIGHT
42.A30V1.002
Case/Cover/Bracket Assembly
103
Chapter 6
Aspire 1360
Picture
Chapter 6
No.
Partname And Description
Part Number
HINGE CAP LEFT
42.A30V1.003
HDD SUPPORT BRACKET
33.A30V1.002
OPTICAL DEVICE SUPPORT
BRACKET
33.A30V1.001
2ND FAN BRACKET
33.A20V1.002
TOUCHPAD COVER
42.A30V1.004
MIDDLE COVER HOOK
31.A20V1.001
UPPER CASE W/COVERSWITCH
CABLE & TOUCHPAD CABLE &
SCROLL KEY
60.A36V1.002
MIDDLE COVER W/LAUNCH BOARD
60.A36V1.003
104
Aspire 1360
Picture
No.
Partname And Description
Part Number
LOWER CASE W/DIMM COVER&
SPEAKER W/O MDC COVER
60.A36V1.001
DIMM COVER W/SCREWS
60.A36V1.007
BLUETOOTH ANTENNA
50.A36V1.001
WIRELESS ANTENNA LEFT/RIGHT
50.A36V1.002
CPU SEMPRON 2800+ 62W AMD
KC.A2802.62D
CPU NB SEMPRON 3000+ 62W AMD
KC.A3002.62D
HDD 40G HITACHI 4200RPM 13G1132
KH.04007.010
HDD 40G TOSHIBA MK4025GAS
KH.04004.002
HDD 40G 4200PRM SEAGATE
ST94019A
KH.04001.010
HDD 60G HITACHI C25N060ATMR04
KH.06007.006
HDD 60G TOSHIBA MK6025GAS
KH.06004.003
HDD 80G HITACHI IC25N080ATMR04
KH.08007.007
HDD 80G TOSHIBA MK8025GAS
KA023A
KH.08004.001
Communication Module
CPU
HDD/ Hard Disk Drive
105
Chapter 6
Aspire 1360
Picture
No.
16
Partname And Description
Part Number
HDD BRACKET
33.E02V1.001
CPU THERMAL PLATE
34.A30V1.001
CPU HEATSINK W/FAN
34.A36V1.001
VGA THERMAL PLATE
33.A36V1.00
VGA THERMAL PLATE (FOR UMA)
33.A36V1.003
KEYBOARD DARFON NSK-ACD1D US
INT
KB.A3007.019
KEYBOARD DARFON NSK-ACD00
SWISS
KB.A3007.016
KEYBOARD DARFON NSK-ACD02
TAIWAN
KB.A3007.020
KEYBOARD DARFON NSK-ACD03
THAILAND
KB.A3007.022
KEYBOARD DARFON NSK-ACD06
PORTUGUES
KB.A3007.004
KEYBOARD DARFON NSK-ACD0A
ARABIC
KB.A3007.005
KEYBOARD DARFON NSK-ACD0C
CZECH
KB.A3007.008
KEYBOARD DARFON NSK-ACD0D
DANISH
KB.A3007.011
KEYBOARD DARFON NSK-ACD0E
ITALIAN
KB.A3007.003
KEYBOARD DARFON NSK-ACD0F
FRENCH
KB.A3007.015
Heatsink
Keyboard
2
Chapter 6
106
Aspire 1360
Picture
No.
Partname And Description
Part Number
KEYBOARD DARFON NSK-ACD0G
GERMAN
KB.A3007.002
KEYBOARD DARFON NSK-ACD0K
KOREAN
KB.A3007.018
KEYBOARD DARFON NSK-ACD0L
GREEK
KB.A3007.017
KEYBOARD DARFON NSK-ACD0M
FRENCH/CANADIAN
KB.A3007.013
KEYBOARD DARFON NSK-ACD0N
NORWEGIAN
KB.A3007.010
KEYBOARD DARFON NSK-ACD0Q
HUNGARIAN
KB.A3007.009
KEYBOARD DARFON NSK-ACD0R
RUSSIAN
KB.A3007.014
KEYBOARD DARFON NSK-ACD0S
SPANISH
KB.A3007.021
KEYBOARD DARFON NSK-ACD0T
TURKISH
KB.A3007.012
KEYBOARD DARFON NSK-ACD0U UK
KB.A3007.001
KEYBOARD DARFON NSK-ACD0W
SWEDISH/FINNISH
KB.A3007.007
KEYBOARD DARFON NSK-ACD1A
BELGIAN
KB.A3007.006
KEYBOARD DARFON NSK-ACD1B
BRAZILIAN
KB.A3007.023
LCD MODULE 15.4" WXGA W/
ANTENNA(QDI)
6M.A36V1.004
LCD MODULE 15.4" WXGA W/
ANTENNA(AU)
6M.A36V1.005
LCD MODULE 15.4" WXGA W/
ANTENNA(HITACHI)
6M.A36V1.006
LCD 15" AU B150XG02 V.2
LK.15005.007
LCD 15" XGA SAMSUNG LTN150XBL03
LK.15006.005
LCD
107
LCD 15.4" HITACHI TX39D85VC1F
LK.15404.003
LCD 15.4" CMO WXGA N154I1-L02
LK.1540D.002
LCD 15.4" WXGA AU B154EW01 V.5
LK.15405.002
INVERTER BOARD 15" SUMIDA TWS458-031
19.T30V1.201
IINVERTER BOARD 15.4" SUMIDA
IV11117/T R.1B
19.A30V1.101
INVERTER BOARD 15.4" DARFON
V0.21071.301
19.A36V1.001
Chapter 6
Aspire 1360
Picture
No.
NS
NS
NS
Chapter 6
Partname And Description
Part Number
LCD BRACKET 15.4" RIGHT
33.A36V1.001
LCD BRACKET ASSEMBLY 15.1
RIGHT
33.A36V1.004
LCD BRACKET 15.4" LEFT
33.A36V1.002
LCD BRACKET ASSEMBLY 15.1 LEFT
33.A36V1.003
INVERTER CABLE
50.A36V1.004
INVERTER CABLE
50.A30V1.001
LCD COAXIAL CABLE 15.4"
50.A30V1.002
LCD COAXIAL CABLE 15.4"
50.A30V1.003
LCD COAXIAL CABLE 15.1
50.A36V1.003
LCD PANEL 15.4" W/HINGE & LOGO
60.A30V1.005
LCD PANEL 15” W/HINGE & LOGO
60.A36V1.005
LCD BEZEL 15.4" W/ICON PLATE
60.A30V1.004
LCD BEZEL 15” W/ICON PLATE
60.A36V1.004
HINGE PACK LEFT/RIGHT
TBD
108
Aspire 1360
Picture
No.
Partname And Description
Part Number
HINGE PACK 15" LEFT/RIGHT
6K.A36V1.001
MAINBOARD W/LAUNCH BOARD
CABLE & MODEM CABLE & RTC
BATTERY
TBD
MAINBOARD W/LAUNCH BOARD
CABLE & MODEM CABLE & RTC
BATTERY & VGA BOARD
TBD
PCMCIA SLOT
22.T30V1.001
TOUCHPAD BUTTON
42.A30V1.005
LCD SCREW CAP LOWER
47.A16V1.001
LCD SCREW RUBBER UPPER
47.A16V1.002
ICON PLATE
40.A30V1.001
LOGO PLATE
31.A30V1.001
SODIMM 256M NANYA
NT256D64SH8BAGM-6K
KN.25603.009
SODIMM 256M SAMSUNG
M470L3224FT0-CB3
KN.2560B.008
SODIMM 256M MICRON
MT8VDDT3264HDG-335F4
KN.25604.021
SODIMM 256M INFINEON
HYS64D32020HDL-6-C
KN.25602.012
SODIMM 512M INFINEON
HYS64D64020GBDL-6-C
KN.51202.013
SODIMM 512M MICRON
MT8VDDT6464HDG-335C1
KN.51204.013
SODIMM 512M SAMSUNG
M470L6524BT0-CB3
KN.5120B.006
Main Board
Miscellaneous
Memory
NS
Optical Drive
109
Chapter 6
Aspire 1360
Picture
No.
Partname And Description
Part Number
CDRW/DVD COMBO MODULE 24X
6M.A36V1.002
DVD-RW MODULE 4X
6M.A36V1.003
CDRW/DVD COMBO DRIVE 24x QSI
SBW-242B
KO.02407.012
CDRW/DVD COMBO DRIVE 24X
PANASONIC UJDA760
KO.02406.001
DVD-RW 4X QSI SDW-042 DUAL
KU.00403.003
OPTICAL BRACKET
33.T30V1.004
PCMCIA SLOT
22.T30V1.001
TOUCHPAD BOARD SYNAPTICS
TM41P-357
56.17001.001
SPEAKER
23.A30V1.001
PCMCIA slot/PC card slot
Pointing Device
NS
Speaker
Screws
Chapter 6
NS
SCW HEX NYL I#R-40/O#4-40 L5.5
34.00015.081
NS
SCRW THERMAL MODULE FOR J8
86.00B54.630
NS
SCREW M2*3 NYLON 1JMCPC-420325 86.9A352.3R0
NS
SCREW M2.5X6
86.9A353.6R0
NS
SRW M2.5*8L B/ZN NYLOK 700
86.9A353.8R0
NS
SCREW M3x4(86.9A524.4R0)
86.9A524.4R0
NS
SCREW M2X2.0
86.9A552.2R0
NS
SCREW WAFER NYLOK NI 2ML3
86.9A552.3R0
NS
SCRW M2*4 WAFER NI
86.9A552.4R0
110
Aspire 1360
Picture
No.
NS
NS
111
Partname And Description
Part Number
SCRW M2.5*3 WAFER NI
86.9A553.3R0
SCRW M2.5*3 WAFER NI
86.9A553.3R0
SCREW M2.5*4L NI
86.9A553.4R0
Chapter 6
Aspire 1520
Picture
No.
Partname And Description
Part Number
Adapter
N/S
ADAPTER 19V 90W 3PIN LITEON PA1900-05QA
TBD
N/S
ADAPTER 19V 90W 3PIN DELTA ADP90SB
TBD
N/S
RTC BATTERY LONGTRUM
23.T30V1.001
18
BATTERY MODULE LI 8CELL
2000MAH SANYO
6M.A36V1.001
N/S
BATTERY LI 8CELL 2000MAH SANYO
BTP-60A1
BT.T3003.001
N/S
BATTERY LI 8CELL SIMPLO BTP-58A1 BT.T3007.003
Battery
CASE/COVER/BRACKET ASSEMBLY
BATTERY COVER
42.A30V1.001
(The cover should be silver not black)
Boards
Chapter 6
VGA BOARD NV36-64M(DIP)
TBD
DC-DC CHARGER BOARD
55.T30V1.001
112
Aspire 1520
Picture
No.
Partname And Description
Part Number
WIRELESS LAN BOARD 802.11BG
FOXCONN
54.A36V1.001
MODEM BOARD AMBIT
T60M283.10(01)
54.09011.544
MODEM/BLUETOOTH BOARD AMBIT
T60M665.00
54.09061.001
LAUNCH BOARD
55.T30V1.002
Cables
POWER CORD 10A 125V US
27.01518.311
COVER SWITCH CABLE
50.A30V1.004
LAUNCH BOARD CABLE
50.T30V1.011
MODEM CABLE 2PIN 2CONNECTOR
55MM
50.41T11.002
MODEM COVER W/SCREWS
42.A20V1.001
HINGE CAP RIGHT
42.A30V1.002
Case/Cover/Bracket Assembly
113
Chapter 6
Aspire 1520
Picture
Chapter 6
No.
Partname And Description
Part Number
HINGE CAP LEFT
42.A30V1.003
HDD SUPPORT BRACKET
33.A30V1.002
OPTICAL DEVICE SUPPORT
BRACKET
33.A30V1.001
2ND FAN BRACKET
33.A20V1.002
TOUCHPAD COVER
42.A30V1.004
MIDDLE COVER HOOK
31.A20V1.001
UPPER CASE W/COVERSWITCH
CABLE & TOUCHPAD CABLE &
SCROLL KEY
60.A36V1.002
MIDDLE COVER W/LAUNCH BOARD
60.A36V1.003
114
Aspire 1520
Picture
No.
Partname And Description
Part Number
LOWER CASE W/DIMM COVER&
SPEAKER W/O MDC COVER
60.A36V1.001
DIMM COVER W/SCREWS
60.A36V1.007
WIRELESS ANTENNA RIGHT (BLACK)
50.A20V1.001
WIRELESS ANTENNA LEFT (GRAY)
50.A20V1.002
BLUETOOTH ANTENNA
50.A36V1.001
CPU SEMPRON 2800+ 62W AMD
KC.A2802.62D
CPU NB SEMPRON 3000+ 62W AMD
KC.A3002.62D
HDD 40G HITACHI 4200RPM 13G1132
KH.04007.010
HDD 40G TOSHIBA MK4025GAS
KH.04004.002
HDD 40G 4200PRM SEAGATE
ST94019A
KH.04001.010
HDD 60G HITACHI C25N060ATMR04
KH.06007.006
Communication Module
CPU
HDD/ Hard Disk Drive
115
HDD 60G TOSHIBA MK6025GAS
KH.06004.003
HDD 80G HITACHI IC25N080ATMR04
KH.08007.007
Chapter 6
Aspire 1520
Picture
No.
16
Partname And Description
Part Number
HDD 80G TOSHIBA MK8025GAS
KA023A
KH.08004.001
HDD BRACKET
33.E02V1.001
CPU THERMAL PLATE
34.A30V1.001
CPU HEATSINK W/FAN
34.A36V1.001
VGA THERMAL PLATE
33.A36V1.00
VGA THERMAL PLATE (FOR UMA)
33.A36V1.003
KEYBOARD DARFON NSK-ACD1D US
INT
KB.A3007.019
KEYBOARD DARFON NSK-ACD00
SWISS
KB.A3007.016
KEYBOARD DARFON NSK-ACD02
TAIWAN
KB.A3007.020
KEYBOARD DARFON NSK-ACD03
THAILAND
KB.A3007.022
KEYBOARD DARFON NSK-ACD06
PORTUGUES
KB.A3007.004
KEYBOARD DARFON NSK-ACD0A
ARABIC
KB.A3007.005
KEYBOARD DARFON NSK-ACD0C
CZECH
KB.A3007.008
KEYBOARD DARFON NSK-ACD0D
DANISH
KB.A3007.011
KEYBOARD DARFON NSK-ACD0E
ITALIAN
KB.A3007.003
Heatsink
Keyboard
2
Chapter 6
116
Aspire 1520
Picture
No.
Partname And Description
Part Number
KEYBOARD DARFON NSK-ACD0F
FRENCH
KB.A3007.015
KEYBOARD DARFON NSK-ACD0G
GERMAN
KB.A3007.002
KEYBOARD DARFON NSK-ACD0K
KOREAN
KB.A3007.018
KEYBOARD DARFON NSK-ACD0L
GREEK
KB.A3007.017
KEYBOARD DARFON NSK-ACD0M
FRENCH/CANADIAN
KB.A3007.013
KEYBOARD DARFON NSK-ACD0N
NORWEGIAN
KB.A3007.010
KEYBOARD DARFON NSK-ACD0Q
HUNGARIAN
KB.A3007.009
KEYBOARD DARFON NSK-ACD0R
RUSSIAN
KB.A3007.014
KEYBOARD DARFON NSK-ACD0S
SPANISH
KB.A3007.021
KEYBOARD DARFON NSK-ACD0T
TURKISH
KB.A3007.012
KEYBOARD DARFON NSK-ACD0U UK
KB.A3007.001
KEYBOARD DARFON NSK-ACD0W
SWEDISH/FINNISH
KB.A3007.007
KEYBOARD DARFON NSK-ACD1A
BELGIAN
KB.A3007.006
KEYBOARD DARFON NSK-ACD1B
BRAZILIAN
KB.A3007.023
LCD MODULE 15.4" WXGA W/
ANTENNA(QDI)
6M.A30V1.001
LCD MODULE 15.4" WXGA W/
ANTENNA(AU)
6M.A30V1.002
LCD MODULE 15.4" WXGA W/
ANTENNA(HITACHI)
6M.A30V1.003
LCD MODULE 15.4" WXGA W/O
ANTENNA(QDI)
6M.A30V1.005
LCD MODULE 15.4" WXGA W/O
ANTENNA(AU)
6M.A30V1.006
LCD MODULE 15.4" WXGA W/O
ANTENNA(HITACHI)
6M.A30V1.007
LCD
117
LCD 15.4" WXGA QDI
LK.15409.001
LCD 15.4" WXGA AU
LK.15405.001
LCD 15.4" WXGA HITACHI
LK.15404.001
INVERTER BOARD 15.4" SUMIDA
19.A30V1.001
Chapter 6
Aspire 1520
Picture
No.
Partname And Description
Part Number
LCD BRACKET 15.4" RIGHT
33.A30V1.004
LCD BRACKET 15.4" LEFT
33.A30V1.005
INVERTER CABLE
50.A30V1.001
LCD COAXIAL CABLE 15.4"
50.A30V1.003
NS
LCD PANEL 15.4" W/HINGE & LOGO
60.A30V1.005
NS
LCD BEZEL 15.4" W/ICON PLATE
60.A30V1.004
HINGE PACK LEFT/RIGHT
TBD
NS
Main Board
LB.A2001.001
MAINBOARD YUHINA 4 W/LAUNCH
BOARD CABLE & MODEM CABLE &
RTC BATTERY (DISCREET VGA-M11P)
PCMCIA SLOT
22.T30V1.001
Miscellaneous
Chapter 6
118
Aspire 1520
Picture
No.
Partname And Description
Part Number
TOUCHPAD BUTTON
42.A30V1.005
LCD SCREW CAP LOWER
47.A16V1.001
LCD SCREW RUBBER UPPER
47.A16V1.002
ICON PLATE
40.A30V1.001
LOGO PLATE
31.A30V1.001
SODIMM 256M NANYA
NT256D64SH8BAGM-6K
KN.25603.009
SODIMM 256M SAMSUNG
M470L3224FT0-CB3
KN.2560B.008
SODIMM 256M MICRON
MT8VDDT3264HDG-335F4
KN.25604.021
SODIMM 256M INFINEON
HYS64D32020HDL-6-C
KN.25602.012
SODIMM 512M INFINEON
HYS64D64020GBDL-6-C
KN.51202.013
SODIMM 512M MICRON
MT8VDDT6464HDG-335C1
KN.51204.013
SODIMM 512M SAMSUNG
M470L6524BT0-CB3
KN.5120B.006
CDRW/DVD COMBO MODULE 24X
6M.A36V1.002
DVD-RW MODULE 4X
6M.A36V1.003
CDRW/DVD COMBO DRIVE 24x QSI
SBW-242B
KO.02407.012
CDRW/DVD COMBO DRIVE 24X
PANASONIC UJDA760
KO.02406.001
DVD-RW 4X QSI SDW-042 DUAL
KU.00403.003
Memory
NS
Optical Drive
119
Chapter 6
Aspire 1520
Picture
No.
Partname And Description
Part Number
OPTICAL BRACKET
33.T30V1.004
PCMCIA SLOT
22.T30V1.001
TOUCHPAD BOARD SYNAPTICS
TM41P-357
56.17001.001
SPEAKER
23.A30V1.001
SCW HEX NYL I#R-40/O#4-40 L5.5
34.00015.081
NS
SCRW THERMAL MODULE FOR J8
86.00B54.630
NS
SCREW M2*3 NYLON 1JMCPC-420325 86.9A352.3R0
NS
SCREW M2.5X6
86.9A353.6R0
NS
SRW M2.5*8L B/ZN NYLOK 700
86.9A353.8R0
NS
SCREW M3x4(86.9A524.4R0)
86.9A524.4R0
NS
SCREW M2X2.0
86.9A552.2R0
NS
SCREW WAFER NYLOK NI 2ML3
86.9A552.3R0
NS
SCRW M2*4 WAFER NI
86.9A552.4R0
PCMCIA slot/PC card slot
Pointing Device
NS
Speaker
Screws
NS
NS
NS
Chapter 6
SCRW M2.5*3 WAFER NI
86.9A553.3R0
SCRW M2.5*3 WAFER NI
86.9A553.3R0
SCREW M2.5*4L NI
86.9A553.4R0
120
121
Chapter 6
Appendix A
Model Definition and Configuration
Model Name Definition
Aspire 1360
Model
Number
LCD
CPU
Memory
HDD
ODD
Wireless
LAN
VGA
1362LMi
15.0"
XGA
Mobile AMD
Sempron
2800+ 62W
2x256MB
60GB
8xDVD-Dual
802.11g
NVIDIA
GeForce
FX
Go5200
64MB
1362WLMi
15.4"
WXGA
Mobile AMD
Sempron
2800+ 62W
2x256MB
40GB
8xDVD-Dual
802.11g
NVIDIA
GeForce
FX
Go5200
64MB
1363WLMi
15.4"
WXGA
Sempron
3000+ 62W
2x256MB
60GB
8xDVD-Dual
802.11g
NVIDIA
GeForce
FX
Go5200
64MB
1362XC
14.1"
XGA
Sempron
2800+ 62W
DDR333
1x256MB
30GB
24x Combo
N/A
UMA
1362LC
15.0"
XGA
Sempron
2800+ 62W
DDR333
1x256MB
40GB
24x Combo
N/A
UMA
1362LCi
15.0"
XGA
Sempron
2800+ 62W
DDR333
2x256MB
60GB
24x Combo
802.11g
UMA
1362WLC
15.4"
WXGA
Sempron
2800+ 62W
DDR333
2x256MB
40GB
24x Combo
N/A
UMA
1362WLCi
15.4"
WXGA
Sempron
2800+ 62W
DDR333
2x256MB
40GB
24x Combo
802.11g
UMA
Aspire 1520
Model
Number
LCD
CPU
Memory
HDD
ODD/Card
Reader
Wireless
LAN
VGA
1522LMi
15.0"
XGA
AMD Athlon
64 3000+
512MB
(2*256)
40GB
DVD-Dual/
PCMCIA 4-in-1
card reader
Ethernet
& 11 g
NVIDIA
Geforce
FX
Go5700
64MB
1522WLMi
15.4"
WXGA
AMD Athlon
64 3000+
512MB
(2*256)
60GB
DVD-Dual/
PCMCIA 4-in-1
card reader
Ethernet
& 11 g
NVIDIA
Geforce
FX
Go5700
64MB
1524WLMi
15.4"
WXGA
AMD Athlon
64 3400+
512MB
(2*256)
60GB
DVD-Dual/
PCMCIA 4-in-1
card reader
Ethernet
& 11 g
NVIDIA
Geforce
FX
Go5700
64MB
Appendix A
112
Aspire 1520
Model
Number
1522LC
113
LCD
15.0"
XGA
CPU
AMD Athlon
64 3000+
82W
Memory
512MB
(2*256)
HDD
40GB
ODD/Card
Reader
24x Combo
Wireless
LAN
N
VGA
64MB
shared
Appendix A
Appendix B
Test Compatible Components
This computer’s compatibility is a test plan released by Acer Internal Testing Department. Once the final report
is available, this chapter will be revised accordingly.
Appendix B
114
Microsoft Windows XP Environment Test
Item
Processor
Specifications
AMD Athlon 64 DTR 3400+
AMD Athlon 64 DTR 3000+
AMD Mobile Athlon XP-M 3000+
AMD Sempron 3000+
AMD Sempron 2800+
Memory
256MB:
Nanya NT256D64SH8BAGM-6K (.14u)
Samsung M470L3224FT0-CB3 (.13u)
Infineon HYS64D32020HDL-6-C 32x64 (.11u/G)
Micron MT8VDDT3264HDG-335F4 (.11u)
512MB:
Infineon HYS64D64020GBDL-6-C (.11u/B)
Micron MT8VDDT6464HDG-335C1 (.11u/512Mb)
Samsung M470L6524BT0-CB300 (512Mb)
LCD
15.4'' WXGA
Samsung LTN154X1-L02
HITACHI TX39D85VC1FAA (low cost)
CMO N154I1-L09 (low cost)
AUO B154EW01 V.5 (low cost)
14.1" XGA
AUO B141XG10
CMO N141XB-L01
Toppoly TD141TGCD1
15” XGA TFT
AUO B150XG02
CMO N150X3-L07
LG LP150X08-A3
Hitachi TX38D81VC1CAB Rev. B
SAMSUNG LTN150XB-L03-C00
15” SXGA+ TFT
AUO B150PG01(NEC)
IDT(CMO) N150P2-L04
SAMSUNG LTN150P4-L03
Hard Disk Drive
30GB HGST Moraga+ HTS24030M9AT00
30GB Toshiba Pluto MK3025GAS
40GB IBM HGST Moraga +, HTS424040M9AT00 13G1132
40GB TOSHIBA Pluto, MK4025GAS ,KA100A
40G Seagate N1, ST94019A, 2MB
60G HGST Moraga IC25N060ATMR04-0
60G TOSHIBA Pluto, MK6025GAS
80G HGST Moraga, IC25N080ATMR04-0 08K635
80G TOSHIBA Pluto, MK8025GAS, 8MB
Combo
QSI Combo 24X QSI/SBW-242B w/ standard bazel
KME Combo 24X , Panasonic 24X COMBO UJDA-760 EGRET BZL
HLDS Combo 24X HLDS GCC-4243N w/ standard bazel
115
Appendix B
Item
DVD Dual
Specifications
QSI DVD Dual 4X, QSI SDW-042 w/ standard bazel
Lite-On DVD Dual 8X , LiteOn SOSW-852S w/ standard bezel
Toshiba DVD Dual 8X, Toshiba L532A w/ standard bazel
Pioneer DVD-dual 8X, Pioneer DVR K14RA w/ stantard bezel
AC Adapter (3 pin)
135W:
Hipro Adapter 135W
Lite-on ADT 135W 3P19V PA-1131 Y3 REV02
Delta ADT 19V135W3P ADP-135DB BBB YU
90W:
Lite-on ADT 19V90W3P PA-1900-05QA EGRT
Delta ADT 19V90W3P ADP-90SB BBE EGRT
Battery Li-Ion, 8 cells
SANYO BTP-60A1
SIMPLO BTY PK Panasonic
Network Adapters
LAN Ethernet/10baseT/100base
3Com Etherlink III 3C589D
IBM EtherJet CardBus
Intel Ether Express Pro/100 Mobile Adapter MBLA3200
Xircom CardBus Ethernet 10/100 32 Bit CBE-10/100BTX
Multifunction Card (Combo)
3Com Megahertz 10/100 LAN + 56K Modem PC Card
Xircom RealPort CardBus Ethenet 10/100 + Modem 56
LAN Token Ring
IBM Token Ring 16/4 Adapter II
Wireless LAN Card
IBM Wireless LAN Cardbus Adapter
Intel Pro-Wireless LAN PC Card
Proxim Skyline 802.11a Cardbus PC Card
Cisco Aironet 350 series Wireless Lan Card
NeWeb Wireless Lan Card 802.11b
Modem Adapters
Modem (up to 56K)
3Com Megahertz 56K Modem PC Card
Xircom CreditCard Modem 56
IBM 56K Double Jack Modem
ISDN
US Robotics Megahertz 128K ISDN Card
IBM OBI International ISDN PC Card
I/O Peripheral
I/O - Display
Acer 211c 21”
Viewsonic PF790 19”
Acer FP751 17” TFT LCD
IBM Color TFT LCD 14”
Compaq Color Monitor
NET Color Monitor 20”
Mozo 17” TFT LCD
I/O - Projector
NEC MultiSync MT-1040
I/O - Legacy (Parallel) Printer/
Scanner
Canon BJC-600J
Epson Stylus Color 740 Parallel Interface
HP DeskJet 890C
HP DeskJet 880C Parallel Interface
HP LaserJet 6MP
HP LaserJet 2200
I/O - IR Printer
HP LaserJet 6MP use IR
HP LaserJet 2200 use IR
Nokia 7210
Appendix B
116
Item
I/O - USB Keyboard/Mouse
Specifications
Chicony USB Keyboard KU-8933
Microsoft Natural Keyboard Pro
Acer Aspire USB mouse
Logicool US Mouse
Logitech Cordless Mouseman Wheel USB Interface
Logitech USB Wheel Mouse M-BB48
Microsoft IntelliMouse Optical USB Interface
I/O - Legacy (PS2/Serial) Keyboard/
Mouse
IBM 101 key keyboard
IBM 109 key keyboard
Acer PS2 keyboard
Acer KB-101A
IBM Numeric Keypad III
IBM Numeric Keypad
Acer Mouse
IBM PS2 Mini Mouse
IBM PS2 Mouse
Logitech Cordless MouseMan Wheel PS2 interface
Logitech Serial Mouse M-M35
Microsoft InteliMouse PS2 interface
Microsoft InteliMouse Optical PS2 interface
Logitech First Mouse Three Button Serial Mouse
I/O - USB (Printer/Scanner)
Epson Stylus Color 740 USB interface
HP DeskJet 880C USB interface
Canon CanonScan D1250 (USB 2.0, JP OS only)
HP ScanJet 3300C Color Scanner
I/O - USB (Speaker/Joystick))
JS USB Digital Speaker
Panasonic USB Speaker EAB-MPC57USB
AIWA Multimedia Digital Speaker
Microsoft SideWinder Precision Pro Joystick
Logitech WingMan RumblePad
I/O - USB Camera
Intel Easy PC Camera
Logitech QuickCam Express Internet
Logitech QuickCam Home PC Video Camera
Orange Micro USB 2.0 Web Cam
I/O - USB Storage Drive
Logitech CDRW +DVDROM combo USB interface
Iomega USB Zip 250MB
I/O-USB Flash Drive
IBM 32MB USB Memory key
Apacer USB Handy Drive 32MB
Apacer USB Handy Drive 256MB
I/O - USB Hub
Belkin 4 Port USB Hub
Eizo I Station USB Hub
Elecom USB Hub 4 Port
Sanwa USB Hub 4 Port
4 Port Hub USB 2.0
I/O - Access Point (802.11b)
Hitachi DC-CN3300
Lucent RG-1000
Lucent WavePoint-II
Cisco Aironet 350
Orinoco AP-500
117
I/O Acess Point (802.11a/b)
Intel Dual Pro/Wireless 5000
I/O Acess Point (802.11a)
Intel Pro/Wireless 5000
Appendix B
Item
Specifications
PCMCIA
PCMCIA - ATA
IBM Microdrive 340MB
IBM Microdrive 1G
Iomega Click! 40MB
Sony Memory Stick 64MB
Sandisk Flash Card 20MB
Apacer SD Flash Card 128MB
Apacer SD Card 256MB
Transcend SD Card 32MB
Hagiwara sys-com SD Card 256MB
PCMCIA - USB 2.0
Apricorn EZ-USB2.0 Cardbus PC Card
DTK USB 2.0 2Port CardBus Host Controller
Adaptec USB2CONNECT
PCMCIA - 1394
Buffalo 1394 Interface Cardbus IFC-ILCB/DV
I-O Data 1394 Interface Cardbus CB1394/DVC
Pixela 1394 Cardbus PC Card PIX-PCMC/FW1
PCMCIA-SCSI
Adaptec 1408 or B SCSI CB
NewMedia Bus Toaster SCSI II
PCMCIA - Bluetooth
IBM Community Bluetooth PC Card
Toshiba Bluetooth PC Card
Appendix B
118
119
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
T
Service guides
T
User's manuals
T
Training materials
T
Main manuals
T
Bios updates
T
Software utilities
T
Spare parts lists
T
Chips
T
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
T
Detailed information on Acer's International Traveller’s Warranty (ITW)
T
Returned material authorization procedures
T
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
120
121
Appendix C
Index
A
E
AFLASH Utility 45
Environmental Requirements 29
Audio 18
Error Symptom-to-Spare Part Index 77
External CD-ROM Drive Check 73
B
Battery 27
F
BIOS 18
package 18
ROM size 18
ROM type 18
vendor 18
Version 18
Features 1
Flash Utility 45
FRU (Field Replaceable Unit) List 100
H
BIOS Setup Utility 32
Hard disk 18, 20
BIOS Supports protocol 18
Hard Disk Drive Module
Disassembly 53
BIOS Utility 32
Hard Disk Standby Mode 29
Basic System Settings 37
Navigating 33
Onboard Device Configuration 40
Startup Configuration 39
System Information 33
System Security 44
Hardware Specifications and Configurations 18
HDD 18, 20
Hibernation Mode 29
Hibernation mode
hotkey 15
Board Layout
Bottom View 5, 99
Top View 4, 98
brightness
Hot Keys 15
I
hotkeys 15
C
Intermittent Problems 88
J
CardBus 27
Jumper and Connector Locations
CD-ROM Interface 20
Chipsets 18
contrast
SW2 Settings 99
K
hotkeys 15
Keyboard 18, 27
Controllers 18
Core logic 18
CPU
core voltage 18
I/O voltage 18
package 18
type 18
Keyboard or Auxiliary Input Device Check 73
L
L2 cache 18
M
Mechanical Specification 29
D
Memory Check 74
Modem 19
Disassembly Flowchart 48
display
hotkeys 15
Display Standby Mode 29
DVD-ROM Interface 21
Index
N
Notebook Manager
hotkey 15
122
O
Windows XP Environment Test 115
Online Support Information 120
P
Panel 5, 99
Bottom 10
Parallel Port 26
PC Card 27
PCMCIA 27
Power Management 29
Power System Check 74
Battery Pack 76
Power Adapter 75
R
Removing the Battery Pack 50
RTC 18
S
Second Level Cache 18
speakers
hotkey 15
Standby Mode 29
Super I/O 18
System Check Procedures 73
System Diagnostic Diskette 45
System Memory 19
System Utility Diskette 45
T
Temperature 29
Touchpad 18
touchpad
hotkey 15
Touchpad Check 76
U
Undetermined Problems 89
USB 26
utility
BIOS 32
V
Video 26
Resolutions 26
Video controller 18
W
123
Index

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project