Apple Projector IN20 Series Reference Guide

IN20 SERIES
Reference Guide
Declaration of Conformity
FCC Warning
Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon
97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that this projector conform to the following
directives and norms:
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: IEC 60950-1: 1st Edition
March, 2006
Trademarks
Canada
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or
registered trademarks of Adobe Systems Incorporated. InFocus, In Focus, and
INFOCUS (stylized) are either registered trademarks or trademarks of InFocus
Corporation in the United States and other countries.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, cUL, TUV
Other specific Country Approvals may apply. Please see product certification label.
This document applies to: IN24, W240, IN26, and W260.
InFocus reserves the right to alter product offerings and specifications at any time
without notice.
1
Important Operating Considerations for Safety
14
Troubleshooting your setup
14
Using the remote control
Using the audio
Using the keypad buttons
22
23
24
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
Using the menus
Picture menu
Advanced menu
Settings menu
Maintenance
Cleaning the lens
Replacing the projection lamp
Using the security lock
25
25
26
26
27
28
29
31
35
35
35
37
Place the projector in a horizontal position no greater than 15 degrees
off axis.
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
•
Use only InFocus-approved ceiling mounts.
•
Use only the power cord provided. A surge-protected power strip is
recommended.
•
Refer to this guide for proper startup and shutdown procedures.
•
This product has a lamp which contains a very small amount of mercury. Wash hands after cleaning the area and handling the ruptured
lamp. Dispose of it as required by local, state or federal ordinances and
regulations. For more information see www.eiae.org.
•
In the unlikely event of a lamp rupture, particles may exit through the
projector side vents. When the projector is turned on, keep people,
food, and drinks out of the "keep out" area under and around the projector, as indicated by the "X" areas below.
8’ / 2
.4 m
/
5’
m
1.5
3’ / 1
m
m
Shutting down the projector
•
3’ / 1
m
/0
.6
3
5
6
9
9
9
10
11
12
13
13
13
13
13
2’
Table of Contents
Introduction
Positioning the projector
Projector and device connector guide
Connecting a computer source
Required computer connections
Optional computer connections
Displaying an image
Adjusting the image
Connecting a video device
Video device connections
Composite video connection
S-video connection
VESA connection
Component video connection
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty booklet.
2
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing too. The IN24 has native SVGA
800x600 resolution while the IN26 has native XGA 1024x768 resolution. This
guide applies to both products. They are compatible with a wide variety of
computers and video devices, including:
•
IBM-compatible computers, including laptops, up to 1024x768 resolution for the IN24 and 1400x 1050 for the IN26.
•
Apple® Macintosh® and PowerBook® computers up to 1024x768 resolution for the IN24 and 1400x 1050 for the IN26.
•
Most standard VCRs, DVD players (progressive and interlaced), progressive DVD, HDTV sources, TV and satellite tuners, camcorders,
video games, and laser disc players.
elevator foot release
keypad
remote control
receiver (IR)
zoom (rear ring)
focus (front ring)
Product specifications
To read the latest specifications on your multimedia projector, be sure to
visit our website at www.infocus.com, as specifications are subject to
change.
Accessories
The standard accessories that came with your projector are listed in the
included user’s guide. Optional accessories can be found on our website at
www.infocus.com or at your retailer or dealer.
Online Registration
Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives.
power cord
connector
connector
panel
3
Connector Panel
The projector provides both computer and video connection options,
including:
•
VESA computer
•
S-video
•
Composite RCA audio/video
computer
USB
monitor
out
S-video
audio
out
security lock
audio in
The projector also provides the following connectors:
•
Monitor out, to provide an image on your desktop computer as well as
on the projection screen
•
Audio out, to provide sound for external speakers
•
USB, to provide mouse control (used with an optional remote control
only)
composite video
4
adjustable
foot
Positioning the projector
Table 1:
Range of distance to the screen for a given screen size
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between
the projector and the rest of your equipment. Here are some general guidelines:
Distance to screen
•
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9 feet (1.5m) from the projection screen.
Diagonal
Screen Size
(inches/m)
Maximum
distance
(feet/m)
Minimum
Distance
(feet/m)
•
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector
within 6 inches (.15m) of a wall or other object.
60/1.5
80/2
92/2.3
150/3.8
8.5/2.5
11.3/3.4
13.0/3.9
21.2/6.4
7.9/2.4
10.6/3.2
12.2/3.7
19.8/6.0
•
If you are installing the projector on the ceiling, refer to the installation
guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling” on page 31. We recommend
using an InFocus authorized ceiling mount.
•
Position the projector the desired distance from the screen. The distance
from the lens of the projector to the screen, the zoom setting, and the
video format determine the size of the projected image.
•
The image exits the projector at a given angle. This image offset is
112.2%. This means that if you have an image 10’ high, the bottom of
the image will be 1.12’ above the center of the lens.
10 ft high
image
Projection angle
bottom of image
1.12 ft above center
of lens
5
lens center
Projector and device connector guide
The following illustration and table should help you find the connectors to
use and obtain the best resolution possible from your input devices, such as
computers, standard VCRs, DVD players (progressive and interlaced),
HDTV sources (1080i and 720p HDTV formats), TV and satellite tuners,
camcorders, video games (progressive and interlaced), and laser disc players.
computer
USB
monitor
out
S-video
audio
out
audio in
composite video
6
Video Device
Standard Broadcast TV (not
HDTV) via: cable, digital
cable, satellite TV, DVD, or
VCR
Standard Video Camera
Video
Compatibility
If Your Device
Connector Is
Attach to Adapter
or Labeled
Connector on
Projector
For Setup Instructions, see
Comments
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 2
or S-video 1
Composite video connection on
page 13.
Not for progressive
(i.e. HDTV) sources.
See page 8.
S-video connection on page 13
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 2
or S-video 1
Composite video connection on
page 13.
Not for progressive
(i.e. HDTV) sources.
See page 8.
S-video connection on page 13
Standard Video Game
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 2
or S-video 1
Composite video connection on
page 13.
S-video connection on page 13
7
Not for progressive
(i.e. HDTV) sources.
See page 8.
Video Device
HDTV
(High Definition TV)
Progressive DVD
Progressive Video Game
Video
Compatibility
If Your Device
Connector Is
Attach to Adapter
or Labeled
Connector on
Projector
For Setup Instructions, see
1080i, 720p
VGA
Computer In
VESA connection on page 13
Component 480i
Component video
Computer In via
optional VESA to
Component adapter
Component video connection on
page 13
1080i, 720p
VGA
Computer In
VESA connection on page 13
Component 480p
and 480i
Component video
Computer In via
optional VESA to
Component adapter
Component video connection on
page 13
1080i, 720p
VGA
Computer In
VESA connection on page 13
Component 480p
and 480i
Component video
Computer In via
optional VESA to
Component adapter
Component video connection on
page 13
8
Comments
Connecting a computer source
connect computer cable
Required computer connections
Connect one end of the provided computer cable to the Computer In connector on the projector and the other to the VESA connector on your computer. If you are using a desktop computer, you will need to disconnect the
monitor cable from the computer’s video port first (you can connect this
monitor cable to the Monitor Out connector on the projector, see below).
Connect the black power cord to the Power connector on the back of the
projector and to your electrical outlet.
connect audio cable
NOTE: Always use the power cord that shipped with the projector.
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the red and/or white Audio In connectors on the projector. You may also need an adapter.
connect monitor cable
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, connect the computer’s
monitor cable to the Monitor Out connector on the projector.
connect USB cable
To advance slides in a PowerPoint presentation using an optional remote
control, plug the USB cable into the USB mouse connector on your computer and the USB connector on the projector.
9
Displaying an image
Press the Power button.
press Power button
The Power light on the Status Indicator Panel (page 14) blinks green and the
fans start to run. When the lamp comes on, the start up screen displays and
the Power light is steady green. It can take a minute for the image to achieve
full brightness.
? No start up screen? Get help on page 14.
turn on computer
or video device
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the
Source button on the projector’s keypad or remote.
If using a laptop, make sure it’s external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD
key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop’s documentation to learn your laptop’s key combination.
activate laptop’s external port
monitor key
or LCD/CRT key
FN key
? No laptop image? Try pressing the Auto Image button on the keypad. Get help on page 15.
10
Adjusting the image
adjust height
If necessary, adjust the height of the projector by pressing the elevator foot
release button to extend the foot.
release button
If necessary, rotate the leveling foot located at the rear of the projector.
elevator
foot
Avoid placing your hands near the hot exhaust vent at the side of the projector.
adjust distance
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
See page 5 for a table listing screen sizes and distances.
adjust zoom or focus
Adjust the zoom or focus.
focus
(front ring)
If the image is not square, first make sure that the projector is perpendicular
to the screen. If the image is larger or smaller on the top or bottom edge of
the screen, press the top Keystone button to reduce the upper part of the
image, and press the bottom Keystone button to reduce the lower part.
adjust keystone
If the left or right side of the screen is larger or smaller the other, you can
turn the projector to the left or to the right a few degrees to square the
image.
Adjust the Contrast or Brightness in the Picture menu. See page 28 for help
with these menu adjustments.
adjust Picture menu
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
regarding Aspect Ratio, see page 12.
11
zoom
(rear ring)
Connecting a video device
4:3 screen
You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. There is also an audio input via the red and white A/V connectors. You can connect the audio directly to the projector to get sound from
the built-in speaker, or you can bypass the projector’s audio system and
connect the audio directly from your source to a stereo or home theater system.
16:9 screen
Do Not Use
4:3
mode
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered
a tuner.
16:9
mode
Before connecting your projector, you should decide which aspect ratio you
want to use. The projector’s Aspect Ratio setting is accessed through the
projector’s Picture Menu. See page 28 for more information.
What is Aspect Ratio?
Aspect ratio is the ratio of the image width to image height. TV screens are
usually 4:3, which is the default for this projector. HDTV and most DVDs
are 16:9. If you’re projecting onto a screen, the size/shape of the screen may
determine which aspect ratio to use. If you are projecting onto a blank wall,
you don’t have the screen size restriction. What you plan to project will also
help you choose between 4:3 and 16:9. Most TV shows are 4:3, while most
movies are 16:9.
Native
mode
(NTSC
only)
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for anamorphic movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies
only appear correctly if the DVD player is set to output to a 16:9 television.
12
Video device connections
Component video connection
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
If your HD video device has component connectors, an optional Component to VESA adapter can be used. Plug the component cable into the video
device. Plug the other end of the component cable into the adapter and plug
the adapter into the Computer in connector. Component offers the highest
quality video output.
Composite video connection
Plug the A/V cable’s yellow connector into the video-out connector on the
video device. Plug the other yellow connector into the yellow Video 2 connector on the projector.
Plug a white connector into the left audio out connector on the video device
and plug a red connector into the right audio out connector on the video
device. Plug the remaining white connector into the white audio in connector on the projector, and plug the remaining red connector into the red
audio in connector on the projector.
Keep in mind that video output from composite connections is not as high
quality as S-video.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an
S-video cable into the S-video connector on your video device and into the
S-video 1 connector on the projector. Use the A/V cable’s red and white
audio connectors as described directly above (the yellow connectors on the
A/V cable are not used).
Keep in mind that S-video delivers higher quality video output than composite.
VESA connection
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the computer
cable into the Computer In connector on the projector.
13
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
Shutting down the projector
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or
keypad button is pressed.
Screen Save
Table 2: Status indicator light behavior and meaning
You can make the black screen appear after a preset number of minutes by
turning on the Screen Save feature in the Settings>System menu. See
page 31.
Status Indicator Panel icons
Meaning
Power, solid green
The power button has been pressed and
the software has initialized or the projector has been powered off.
Power, blinking green
To turn the projector off, press the Power button on the remote or keypad
two times (the second time verifies the shut-down request). The lamp turns
off and the Power light on the Status Indicator Panel blinks green for one (1)
minute while the fans continue to run to cool the lamp. While the light is
blinking green, the projector does not accept any keypad and remote control
input. When the lamp has cooled, the Power light is solid green.
The power button has been pressed and
the software is initializing, or the projector is powering down and the fans are
running to cool the lamp.
Thermometer
The projector is too hot. Make sure the
vents aren’t blocked (see page 20). Turn
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists.
Troubleshooting your setup
Lamp
Turn off the projector and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one
minute, then turn the projector on again.
If the service lamp turns on again, service
is required. Visit www.infocus.com/service
to contact Service.
Power Save
The projector also has a Power Save feature that automatically turns the
lamp off after no active sources are detected and no user interaction with
the projector is performed for 20 minutes. By default, this feature is off. See
page 31.
Turning off the projector
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
14
Problem
Solution
Result
no start up screen
plug power cord into the projector
press power button
correct image
Startup
Screen
only start up screen appears
press the Source button
activate laptop’s external port
computer image projected
Startup
Screen
A
A
A
restart laptop
15
no computer image, just the words “Signal out of
range”
Signa
l
rang out of
e
press the Auto Image button on keypad
computer image projected
adjust computer refresh rate in Control
Panel>Display>Settings>Advanced>Adapter
(location varies by operating system)
A
A
A
you may also need to set a different
resolution on your computer, as shown
in the following problem, “image fuzzy
or cropped”
Only my laptop’s background appears, not the
Desktop icons
Disable “Extend my Windows Desktop” in
Control Panel>Display>Settings>Display 2
(location varies by operating system)
Background and Desktop projected
A
A
A
A
Uncheck this
option, then
click Apply
16
Problem
Solution
image fuzzy or cropped
A
A
Result
set your computer’s display resolution to
the native resolution of the projector
(Start>Settings>Control
Panel>Display>Settings tab)
select 800x600 for IN24 and 1024x768 for
IN26
image clear and not cropped
A
For a laptop,
disable laptop
monitor
or turn-on dualdisplay mode
move projector, adjust zoom, adjust height
image not centered on screen
correct image
adjust horizontal or
vertical position in
Picture>Advanced
menu
17
Problem
Solution
Result
image not square
adjust Keystone on keypad
square image
image not sharp
adjust Sharpness in the Picture>Advanced
menu
correct image
AB
AB
image does not fit 4:3 or 16:9 screen
change aspect ratio to 4:3 or 16:9 in
Picture>Aspect ratio menu
18
correct image
Problem
Solution
Result
image upside down
turn off ceiling in Settings>System menu
correct image
AB
AB
image reversed left to right
turn off rear in Settings>System menu
correct image
A
projected colors don’t match source
AB
adjust color, tint, color temperature,
brightness, contrast, color space in the
menus
COLOR
correct image
COLOR
19
Problem
Solution
Result
The video embedded in my PowerPoint
presentation does not play on the screen
turn off the internal LCD display on your
laptop
Embedded video plays correctly
A B
A
A
B
lamp won’t turn on, Temperature light is on
make sure vents aren’t blocked, turn off the
projector and allow it to cool for one
minute
lamp turns on
Startup
Screen
Temperature light
20
Problem
Solution
Result
“Change lamp” message appears at startup, lamp
won’t turn on, Lamp light is turned on
lamp must be replaced (see page 35)
lamp turns on
Startup
Screen
Lamp light
replace lamp
Still need assistance?
If you need assistance, visit our website at www.infocus.com/service or call
us. Check out our HOW TO section there for additional information on
using this projector for home theater or gaming applications. See the user’s
guide for support contact information.
This product is backed by a limited warranty. An extended warranty plan
may be purchased from your dealer. When sending the projector in for
repair, we recommend shipping the unit in its original packing material, or
having a professional packaging company pack the unit. Please insure your
shipment for its full value.
21
Using the remote control
The remote uses two (2) provided AA batteries. They are easily installed by
sliding the cover off the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.
navigation
buttons
Caution: When replacing the batteries, be aware that using batteries other
than the type provided with the projector may risk severe damage to the
remote. When disposing of the batteries, be sure to do so in an environmentally proper manner.
To operate, point the remote at the front of the projector (not at the computer). The range of optimum operation is about 15 feet (4.5m).
Press the remote’s Power button to turn the projector on and off (see
page 14 for shutdown info).
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 27 for more info on the menus.
The remote also has a Source button to switch between sources.
Troubleshooting the remote
•
Make sure the batteries are installed in the proper orientation and are
not dead.
•
Make sure you’re pointing the remote at the projector or the screen, not
the computer, and are within the remote range of 15 feet (4.5m). For
best results, point the remote at the projector.
22
Using the audio
connect audio cable
Using the projector’s speaker
To use the projector’s speaker, connect your source to the Audio In connectors (L and/or R) on the projector’s composite connectors.
To adjust the volume, press the Volume buttons on the keypad.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
Make sure the audio cable is connected.
•
Make sure the volume is turned up enough. Press the Volume button
on the keypad or remote.
•
Make sure the correct source is active.
•
Make sure that you are connected to an “audio out” connector on the
source as opposed to a “line-in” or “microphone” connector.
•
Adjust the audio source.
•
If playing a video, make sure the playback has not been paused.
adjust volume
Connecting external speakers
The projector can be attached to external amplified speakers by connecting a
3.5mm stereo audio cable from the Audio Out connector on the projector to
the amplified speakers. Alternatively, you can bypass the projector’s audio
system and connect the audio directly from your source to a stereo or home
theater system.
external speakers
with own power source
audio out
speaker
cable
23
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their functions:
Power–turns the projector on and off (page 10).
Auto Image–resets the projector to the source.
Presets–cycles through the available preset settings (page 29).
Keystone–adjusts squareness of the image (page 11).
Menu–opens the on-screen menus (page 27).
menu navigation
buttons
Select–confirms choices made in the menus (page 27).
Up/Down arrows–navigates to and adjusts settings in the menus (page 27).
Volume–adjusts sound (page 23).
Source–changes the active source.
24
Optimizing computer images
Presentation features
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 27.
Several features are provided to make giving presentations easier. Here is an
overview, details are found in the menu section.
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu
(page 28).
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 28).
•
Adjust the Color Temperature in the Advanced menu (page 30).
•
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu (page 29).
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later (page 29).
25
•
The Custom key, available on several optional remotes only, allows you
to assign various features to the button. The default effect is Source
Info, which displays information about the projector and current
source. See page 32 for details.
•
The Startup Logo option lets you change the default start up screen to a
blank or default screen (page 32).
•
Two options, Power Save and Screen Save, are provided to automatically shut down the projector after several minutes of inactivity or display a black screen. This helps preserve lamp life (page 31).
Optimizing video images
Customizing the projector
After your video device is connected properly and the image is on the
screen, you can optimize the image using the onscreen menus. For general
information on using the menus, see page 27.
You can customize the projector for your specific setup and needs. See
page 31 to page 33 for details on these features.
•
For rear projection, turn rear mode on in the Settings>System menu.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu (page 28).
•
For ceiling mounted projection, turn ceiling mode on in the Settings>System menu.
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 28).
•
Specify which source the projector checks first for active video during
power-up.
•
Select a Sharpness setting (page 30).
•
Specify the function of the Custom key on the optional remote.
•
Use the Color Control to adjust the color gain (page 30).
•
Turn the projector’s display messages on and off.
•
Adjust the Color Temperature. Select a listed warmth value (page 30).
•
Turn on power saving features.
•
Turn on Overscan to remove noise on the edges of the image.
•
Specify blank screen colors and start up logos.
•
Specify the language viewed on the menus.
•
Save settings for the active source as a preset.
26
Using the menus
keypad navigation
buttons
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button.
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio buttons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Previous or Exit, then press Select to
go to the previous menu; press the Menu button at any time to close the
menus.
Main menu
dots
Dots appears before the menu name. The number of dots indicate menu’s
level, ranging from one (the Main menu) to four (the most nested menus).
The menus are grouped by usage:
•
The Picture menu provides image adjustments.
•
The Settings menu provides set-up type adjustments that are not
changed often.
•
The Source Info menu provides a read-only display of information
about the projector and source.
Picture
menu
Certain menu items may not be visible or may be grayed depending upon a
particular source being connected. For example, Sharpness is only available
for video sources and is not visible when a computer source is active. Menu
options are grayed out only if the source is selected but no signal is present.
For example, if the projector is set to a video source but the source, such as a
DVD player, is turned off video menu options are grayed out.
Settings
menu
Source Info menu
27
Picture menu
To adjust the following settings, highlight the setting, press Select, use the
up and down arrows to adjust the values, then press Select to confirm the
changes.
Picture menu
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
increasing keystone
Brightness: changes the intensity of the image.
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint: adjusts the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 4:3. HDTV and most DVDs are 16:9. The default is
4:3.
Select Native to see the unmodified input with no resizing by the projector.
Select 16:9 to watch enhanced widescreen DVDs.
Aspect ratio
For more information regarding Aspect Ratio, see page 12.
28
decreasing keystone
Presets: Presets are provided that optimize the projector for displaying
computer presentations, film images, and video images. Film input is material originally captured on a film camera, like a movie; video input is material originally captured on a video camera, like a TV show or sporting event.
Presets
There are also user-definable presets. To set a preset for the current source,
adjust the image, select Save Settings in the Presets menu, then select Save
User 1 (or 2 or 3). You can recall these settings in the future by selecting the
User 1 preset. If you select User Presets then further adjust the image, Presets Off will automatically be selected in the Preset menu to indicate
changes have been made.
Save
User
Settings
To restore the factory default settings, choose Factory Reset in the Settings>Service menu (page 33).
Advanced menu
The following four (4) options are for progressive and computer sources.
Advanced menu
Phase: adjusts the horizontal phase of a computer source.
Tracking: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer source.
Sync Threshold Adjust: (progressive signals only) If a hardware device,
such as a DVD player, is not syncing properly with the projector, select this
option to help it to sync when connected to the projector.
White Peaking: (video sources only) increases the brightness of whites that
are near 100%.
Overscan: removes noise around the video image.
29
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Color Space: This option applies to computer and component video
sources. It allows you to select a color space that has been specifically tuned
for the input signal. When Auto is selected, the projector automatically
determines the standard. To choose a different setting, turn off Auto, then
choose RGB for computer sources, choose either REC709 or REC601 for
component video sources.
Sharpness
Color Temperature: changes the intensity of the colors. Select a listed relative warmth value.
Color
Space
Color Control: allows you to individually adjust the gain (relative warmth
of the color) and the offset (the amount of black in the color) of the red,
green, and blue colors. Note that offset adjustments are only available for
computer sources.
Color
Temperature
Video Standard: when it is set to Auto, the projector attempts to automatically pick the video standard based on the input signal it receives. (The
video standard options may vary depending on your region of the world.) If
the projector is unable to detect the correct standard, the colors may not
look right or the image may appear “torn.” If this happens, manually select
a video standard by selecting NTSC, PAL, or SECAM from the Video Standard menu.
Color Control
Video Standard
30
Settings menu
Audio: allows adjustments to Volume of the internal speaker and allows a
chime to play when starting the projector. Volume adjustments can also be
made from the projector’s keypad.
Settings menu
Sources: Power-up Source determines which source the projector checks
first for active video during power-up. When the Autosource feature is On,
the projector automatically finds the active source, checking the selected
Power-up Source first. The source options are Computer for a computer,
progressive DVD, or HDTV source, and S-video and Composite for video
sources. When this feature is Off, the projector defaults to the source
selected in Power-up Source. To display another source, you must manually
select one by pressing the Source button on the remote or keypad.
Audio
Sources
System>Rear: reverses the image so you can project from behind a translucent screen. Ceiling: turns the image upside down for ceiling-mounted projection. Low Power: toggles between on and off. Turn it on to lower the light
output of the lamp. This also lowers the fan speed, making the projector
quieter. Auto Power: When Auto Power is checked, the projector automatically starts up after the projector is powered on. This allows control of ceiling mounted projectors with a wall power switch. Display Messages:
displays status messages (such as “Searching”) in the lower-left corner of
the screen. PC Screen Saver Off: prevents your computer from going into
Screen Save mode. The projector must be connected to the PC via a USB
cable for this feature to work. Power Save: automatically turns the lamp off
after no signals are detected for 20 minutes. After 10 additional minutes
with no signal, the projector powers down. If an active signal is received
before the projector powers down, the image will be displayed. After an
additional 10 minutes with no signal, the projector powers down and can be
toggled off. If an active signal is received before the projector powers down,
the image will be displayed. When Power Save is enabled, Screen Save is
disabled. Screen Save automatically blanks the screen with a black color
after no signals are detected for a preset number of minutes. The image
returns when an active source is detected or a remote or keypad button is
pressed.
Power-up
Source
Screen Save
System menu
31
Startup Logo: allows you to display a blank screen instead of the default
screen at startup, and when no source is detected.
Blank Screen: determines what color is displayed when you press the
Blank button on the remote.
Startup Logo
Blank Screen
Custom Key (for use with optional remote only): allows you to assign a different function to the Custom button on an optional remote, allowing you to
quickly and easily use the effect. Highlight an effect and press Select to
choose a different one.
•
Blank: displays an empty screen.
•
Mute: turns off all sound.
•
Aspect Ratio: toggles among 4:3, 16:9, and Native (see page 12 and
page 28).
•
Source: cycles through available sources.
•
Auto Image: resets the projector to the source (page 24).
•
Freeze: pauses the projected image.
•
Source Info: the default effect. It opens a window with projector and
source information.
•
Service Info: opens a window with projector and source information.
Custom Key
32
Language: allows you to select a language for the onscreen display.
Language menu
Service menu
Service: To use these features, highlight them and press Select.
Factory Reset restores all settings to their default. Reset Lamp Hours
resets the lamp hours used counter in the Service Info menu to zero. Do this
only after changing the lamp. PIN functionality, see the next section. Test
Pattern allows you to display certain patterns to adjust the image. This feature only works with an optional remote. To display test patterns, click the
Test Pattern check box, exit the menus, then press the Blank button on the
remote. To select the patterns, use the up/down arrows on the remote or
keypad. To exit the test patterns, press the Blank button again.
appears only when PIN is disabled
appears only when PIN is enabled
Service Code: only used by authorized service personnel. Service Info:
provides information about the projector and lamp.
Service Info menu
33
PIN feature
The PIN (personal identification number) feature allows you to password
protect your projector. Once you enable the PIN feature, you must enter the
PIN before you can project an image.
To use this feature, you must register your projector at www.infocus.com/
register and follow the instructions there to get a default PIN. The PIN consists of a sequence of 5 navigation button presses. The navigation buttons
are menu, select, up arrow and down arrow. Once you have this PIN, select
Enable PIN in the Service menu. The Enter PIN dialog box appears.
Use the navigation buttons on the remote or keypad to enter the correct button press sequence. After pressing the first button, a dot appears in the current PIN slot and the highlighted cursor moves to the right one slot. When
all 5 numbers are entered correctly, press the Select button on the remote or
keypad to select OK. If the message “Incorrect PIN” appears, verify the code
and re-enter it. If you mis-enter a number, you must enter 5 numbers and
press the Select button in order to access the “Incorrect PIN” message and
re-enter the code.
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the startup screen. Enter the PIN. Use the navigation buttons on the remote or keypad to enter the correct button press sequence. See the description above for
instructions. If you lose or forget your PIN, go to www.infocus.com/pin.
To change the PIN:
Select “Change PIN” in the Service menu. Enter the existing PIN. Enter the
new PIN. You can navigate between OK and Cancel by pressing the up and
down buttons on the keypad. Select OK or Cancel by pressing the Select
button. Verify the new PIN.
To reset the PIN back to the default:
Power up the projector. After the “Enter PIN” dialog box appears, press and
hold the Select button down for 10 seconds. Enter the default PIN to use
the projector. If you lose or forget your default PIN, go to
www.infocus.com/pin.
34
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion.
Replacing the projection lamp
The lamp hours used timer in the Service Info menu counts the number of
hours the lamp has been in use. Twenty hours before the lamp life expires,
the message “Change lamp” appears on the screen at startup.
Lamp hours
NOTE: You can order new lamp housings from www.infocus.com (in select
areas), your retailer or your dealer. Use only a replacement lamp with the
same type and rating as the original lamp.
turn off and unplug
projector
.
1 Turn off the projector and unplug the power cord.
2 Wait 60 minutes to allow the projector to cool thoroughly.
3 Turn the projector upside down on a soft cloth so that the lamp door is
facing you.
4 Slide the lamp door off.
lamp door
35
wait 60 minutes
WARNING:
Be extremely careful when removing the lamp housing. In the
unlikely event that the bulb ruptures, small glass fragments may be
generated. The lamp housing is designed to contain these fragments, but use caution when removing the lamp housing. Before
replacing the lamp, clean the lamp compartment and dispose of
cleaning materials. Wash hands after lamp replacement. This product has a lamp which contains a very small amount of mercury. Dispose of it as required by local, state or federal ordinances and
regulations. For more information see www.eiae.org.
squeeze lamp connector
5 Detach the lamp connector from the projector by depressing the locking
tab on the connector and lightly pulling it free.
6 Loosen the captive screw that attaches the lamp housing to the projector.
Carefully remove the lamp housing. Dispose of the lamp in an environmentally proper manner.
loosen screw
7 Install the new lamp housing and tighten the screw.
8 Re-attach the lamp connector to the projector. The locking tab should
engage when the connector is fully plugged in.
9 Replace the lamp door by sliding it into place. Be sure the lamp connector wires are not in the way.
10 Plug in the power cord and press the Power button to turn the projector
back on.
11 To reset the lamp hour timer, navigate to the Settings>Service menu
and select Reset Lamp Hours. See page 33 for details.
Service menu
36
Using the security lock
The projector has a security lock for use with a PC Guardian Cable Lock
System. Refer to the information that came with the lock for instructions on
how to use it.
security
lock
37
INDEX
C
cable box 12
cleaning the lens 35
Color 28
Color Control 30
Color Space 30
Color Temperature 30
compatibility
IBM-compatible 3
Macintosh 3
video devices 3
Computer In connector 9
connecting
computer 9
computer monitor 9
external speakers 23
video device 12
connector panel 4
connectors on projector 7, 8
contacting InFocus 21
Contrast 28
Custom key 25, 32
customer service contact information 21
customizing the projector 26
Numerics
16x9 vs 4x3 12
A
Advanced menu 29
Aspect Ratio 12, 28, 32
Audio In connector 9, 13, 23
audio input 12
Audio menu 31
Autosource 31
B
Blank Screen 32
Brightness 28
D
Display Messages 31
DVDs 28
F
Factory Reset 33
focus 11
38
H
HDTV 6, 28
Horizontal 29
P
password-protecting the projector 34
PC Screen Saver Off 31
personal identification number 34
Phase 29
Picture menu 28
PIN 34
positioning the projector 5
Power connector 9
power cord 9
Power Save 14, 31
Power-up Source 31
presentation features 25
Presets 29
projection distance 5
projector
connecting computers 9
connecting video devices 12
connector panel 4
customization 26
image size 5
keypad buttons 24
language 33
maintenance 35
menus 27
offset 5
password-protecting 34
PIN 34
positioning 5
registering 3
reset 33
resolution 3
safety considerations 2
I
IBM-compatible computers 3
image
optimization 25
size 5
K
keypad buttons 24
keystone, adjusting 11
L
lamp hours, resetting 36
lamp replacement 35
Language 33
laptop video port activation 10
LEDs 14
Low Power 31
M
Macintosh computers 3
maintaining the projector 35
Menu button 27
menu usage 27
Monitor Out connector 9
O
optimizing images 25
optimizing video 26
Overscan 29
39
security lock 37
setting up 5
shutting down 14
Status Indicator Panel 14
troubleshooting problems 14
T
Tint 28
Tracking 29
troubleshooting 14
TV tuner 12
R
Rear 31
registering your projector 3
remote control 22
replacing the lamp 35
resetting the projector 33
resolution 3
U
USB 4, 9
V
Vertical 29
video devices, connecting 13
video optimizing 26
Video Standard 30
Volume button 23
S
Screen Aspect 12
Screen Save 14, 31
security lock 37
Service 33
Service Code 33
Settings menu 31
sharpness 30
shutting down the projector 14
Sources 31
speakers, connecting external 23
Startup Logo 32
Status Indicator Panel 14
S-video connector 13
System 31
W
warranty 21
Z
zoom 11
40