- Home
- Domestic appliances
- Climate control
- Fireplaces
- Empire Comfort Systems
- Stove MS-100
- Assembly Instructions
advertisement
▼
Scroll to page 2
SUPERB GAS STOVES R-3088 Assembly Instructions Effective Date November, 2001 WARNING If not assembled, operated and maintained in accordance with the manufacturers instructions, this product could expose you to property damage, personal injury or loss of life from fire, explosion or asphyxiation. Read all warnings below. WARNING 1. The following model numbers are for indoor or outdoor use in Canada. The following model numbers are for outdoor use only in United States. ES-100, ES-200, ES-300, MS-100, MS-200, MS-300, ES-S100, ES-S200, ES-S300. Attention: Portable (20 lb.) cylinder can not be used indoors. The following model numbers are for outdoor use only in Canada and United States. SE-200 and SE-300. 2. Do not leave appliance unattended while in use or hot. Never move cooker while in use or hot. 3. A fire can occur from overheated oil or grease. 4. Oil may heat faster than expected. 5. Use a thermometer to monitor oil temperature. 6. Do not use appliance on or near combustible surfaces, wood decks, storage sheds, garages, shrubbery, trees, houses, etc... 7. Do not cover the pot when heating oil or grease. 8. Should grease fire occur, turn off the gas and cover the pot with the lid. 9. Check every fitting for gas leaks before each use. 10. Never stand over burner while lighting; this could result in serious injury. Carefully follow lighting instructions. 11. Keep children and pets at a safe distance. 12. Never place empty containers over an open flame. 13. Do not attempt to change valve depth into burner or reassemble parts. 14. Never store propane tank in an enclosed area. If cooker is stored in doors after use, disconnect the propane tank for outdoor storage. 15. The Superb regulator and hose assembly must be used, no substitutions. Other regulators or no regulator used at all could result in dangerous gas leakage and improper burner performance. 16. Never install or remove the propane tank while cooker is in use or too hot to touch. 17. Always inspect hose kit before each use. Protect hose from cuts, heat or abrasions. Never use a hose that indicates signs of cracking or damage. 18. Never allow hose to contact any part of the cooker while in use or still hot. Place propane tank from cooker so that the hose length will not be in the way. Keep all connections and fittings clean, replace any damaged parts. 19. Never store the propane tank near high heat, open flames, direct sunlight or where high temperature exist. Assembly Instructions REQUIRED TOOLS: Pliers or adjustable wrench and screwdriver. 1. Bolt legs in place by inserting short bolts through holes in corners of main top, then through slot at top of leg. Screw nuts onto the bolts. Attach drip pan using four of the short bolts. Insert bolts through hole in center of leg and through corner of pan. Apply nuts and tighten securely. Now tighten leg bolts. 2. Install manifold clamps. Insert two long bolts through manifold clamp holes in the main top. Attach the two manifold clamps loosely R-3088 Model Numbers ES-100, ES-200, ES-300 MS-100, MS-200, MS-300 (9,000 Btu per Burner) ES-S100, ES-S200, ES-S300 SE-200, SE-300 (10,000 Btu per Burner) underneath top, using nuts. Place manifold pipe with valves attached into the clamps. Align the gas valves with center of large opening in top. The adjusting hood of the valve should face the rear of the stove. Now tighten the manifold clamps securely. Place the valve knobs on valve stem, making sure that the control valve is in the off position. Knob should be in the vertical position. Manifold Pipe thread is 3/8 male IPS. 3. To install burners: If stove is to be used with LP or bottled gas, the air shutter (round metal disc) should be partially opened and then locked in place by tightening the air shutter screw. The hole in open end of burner slides over the adjusting hood of the gas valve. The rear part of the burner is attached to hole underneath main top using long bolts with nuts. Fasten securely. 4. The grates are installed by inserting the two extended legs on grate into corresponding holes in main top on each side of burner opening. 5. Always use teflon tape or thread sealer on pipe threads. FOR MINI-STOVE MODELS (NUMBER MS-100, MS-200, MS300)) 6. Remove the main top by pulling upward. Install the two manifold clamps, using the long bolts with nuts, to the bottom front of frame. Do not tighten clamps. 7. Insert the manifold pipe with valves attached into the clamps; open end of manifold should extend through hole in left side of frame. Tighten the manifold clamps. Burners are fastened to burner hangers already installed. Then assemble in same manner as above. CHECK FOR GAS LEAKS After assembly is complete, connect stove to gas supply and check for gas leaks before lighting. Make sure proper fittings are used for connection. (To operate gas valve, push in before turning.) GRATE 1. Turn brass control valve so knob is in vertical position untilBURNER it is TOP tight. (This shuts off flow of gas from the regulator to the burner. 2. Open LP cylinder valve or gas supply by 1/4"1/4 BOLT turn. This allows gas into the regulator and stops it at the brass VALVE 1/4" HEX control valve. FLANGE NUT KNOB 3. Apply gas detector fluid (or soapy dishwashing solution) on all connections, especially around the regulator, valve and POLcylinder connection. Any bub-bles that appear indicate BODY a gas leak. If so, turn off gas and tighten the fitting. If a leak persists, pipe thread compound may be needed on LEG the threads. Model No. NEVER USE A FLAME TO CHECK FOR GAS LEAKS. SE-200 w/SLK-28 TO LIGHT 1. When you are sure there are no gas leaks, turn cylinder valve and brass control valve to closed position. (To operate gas valve, push in before turning.) Cylinder Service Valve 2. Re-open LP cylinder valve fully. Handwheel 3. Re-open brass control valve 1/4 turn. POL Connector 4. Keeping hands and face away from the top Pressure Relief Valve of the burner, light with a fireplace match Regulator or long-nose lighter. 5. Adjust the brass control valve for desired flame height. WRENCH TIGHTENED ASSEMBLY WARNING: NEVER PUT HANDS OR FACE DIRECTLY OVER BURNER WHILE LIGHTING You may adjust valve setting at this time. The flame should show a Empire Comfort Systems, Inc. • 918 Freeburg Avenue • Belleville, IL 62222 Page 1 SECTIONAL PARTS FOR GAS STOVE SP-010 S-1111 SP-067 S-1188 S-1266 P-221 SP-011 S-1122 SP-012 S-1133 SW2-1 SP-034 S-1277 R-3337 S-1288 SP-016 S-1366 SP-010 One-Burner Top SP-011 Two-Burner Top SP-012 Three-Burner Top SP-076 One-Burner Semi-Enclosed Frame* SP-064 Two-Burner Semi-Enclosed Frame SP-063 Three Burner Semi-Enclosed Frame SP-065 One-Burner Mini-Stove Frame SP-066 Two-Burner Mini-Stove Frame SP-067 Three-Burner Mini-Stove Frame * Not Shown SP-064 S-1144 SW3-1 SP-013 S-1211 R-3338 S-1299 S-1300 SP-028 S-1377 SP-013 SP-014 SP-015 P-220 P-219 P-221 SP-034 R-3337 R-3338 greenish blue inner cone with a slight yellow tip. If necessary, you can make an adjustment by turning the hood of the valve in a counterclockwise direction until the flame performance is satisfactory. See other side for further instructions regarding valve setting. SP-063 S-1155 SP-065 S-1166 SP-014 S-1222 SP-015 S-1233 S-1311 R-3339 S-1380 P-220 S-1244 P-219 S-1255 SP-062 S-1333 S-1322 SP-055 S-1389 One-Burner Drip Pan Two-Burner Drip Pan Three-Burner Drip Pan One-Hole Manifold Two Hole Manifold Three Hole Manifold Manifold Clamp Knob Gas Valve GRATE SP-066 S-1177 SP-028 Burner hanger R-3339 Grate SP-055 Round Burner SP-062 Star Burner SP-016 6" Low Leg S-1377 28" High Leg S-1380 32" High Leg S-1388 Leg Brace for 32" High SW2-1 Two-Burner Windscreen SW3-1 Three-Burner Windscreen BE MADE TO THE GAS VALVE AND BURNER ASSEMBLY. STOVE GAS ENTRANCE MANIFOLD CLAMP MANIFOLD DUST COVER BURNER DO not tamper with or attempt repairs on the burners, frames valves, or LP cylinder. Allow only qualified LP Gas LEG Dealers to make repairs and adjustments. GAS VALVE AIR SHUTTER DRIP PAN Always close LP cylinder valve after KNOB use. Always use and store bottle in an upright position. Never store or transport these cylinders in an occupied enclosure. Adjustment Instructions-Universal Gas Valve Your portable gas stove is furnished with A.G.A. listed Universal type Gas Valve. This valve is designed for use with (Liquefied Petroleum LPG), Natural or Manufactured Gas. When gas plate is installed the valve should be set for the kind of gas to be used. The universal valve is adjusted for the various gases by turning the ADJUSTING HOOD. To turn HOOD use wrench on HOOD SHOULDER. This may be done after gas stove is assembled as HOOD SHOULDER is easily accessible. 1. This valve is shipped from the factory adjusted for LP gas. If LP gas is to be used, no adjustments should be necessary. Orifice HOOD can be open slightly to get desired flame. 2. For use with Natural or Manufactured gas open HOOD until the proper amount of gas is fed to each burner. When properly adjusted the flame should have greenish blue inner cones about one-half inch long. An unnecessary high flame is wasteful and inefficient. 3. The air shutter for each burner should be adjusted so the flame burns clean without blowing. After you obtain the correct setting or the air shutter, lock in place by tightening the air shutter screw. ADJUSTING PIN STEM HOLE IN ADJUSTING PIN ADJUSTING HOOD ADJUSTING HOOD SHOULDER VALVE BODY Warranty Empire Comfort Systems, Inc. makes no claim of fitness of this product for a particular purpose or use and assumes no liability for damages resulting from the use of the product. Liability of the manufacturer in any event is limited to the amount of the original purchase price of this product. This warranty applies only to the use of the product in accordance with the manufacturer's operating instructions, and remains in force only so long as the product remains in its original configuration. This warranty does not apply to products that have been altered or repaired by outside agents, abused, damaged through neglect, misuse, or accident, or to products that have been used in any way other than in accordance with manufacturer's operating instructions. There are no other warranties, expressed or implied, pertaining to this product or any other product sold by us. Empire Comfort Systems, Inc. neither assumes any responsibility in its behalf for operation of this or any other product manufactured or sold. CAUTION: Orifice HOODS must again be turned down, if the gas stove is to be used on LP gas after it has once been adjusted for other gases. UNDER NO CIRCUMSTANCES SHOULD ANY ALTERATIONS CAUTION: MAXIMUM WORKING PRESSURE 1/2 P.S.I. 11-INCH WATER COLUMN Page 2 (LOW PRESSURE REGULATOR IS REQUIRED) R-3088
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement