I. Tech Dynamic | Headphones Bluetooth Stereo Headphone | User manual | i. Tech Dynamic Headphones Bluetooth Stereo Headphone User manual

i. Tech Dynamic Headphones Bluetooth Stereo Headphone User manual
Contents
Product Specifications
BlueBAND Sport Overview
Getting Started
Charging Your Headphones
Pairing Your Headphones with a Bluetooth Mobile Phone
Turning Your Headphones On and Off
Using Your Headphones
Resetting Your Headphones / Removing the Pairing History
Troubleshooting
Safety Information
Care and Maintenance
Declaration of Conformity
Federal Communications Commission (FCC) Statement
3
4
4
5
6
7
8-9
10
11
12
13-14
15
16
BlueBAND Sport
Bluetooth Stereo Headphones
2
Product Specifications
1.
2.
3.
4.
5.
6.
7.
8.
v2.0+EDR Class 2
Headset, Handsfree, A2DP & AVRCP
2.4GHz Spectrum
10 meters
Within 3 hours
Up to 8 hours
Up to 8 hours
Up to 200 hours
90 (L) x 80 (W) x 118 (H) mm
72.6 grams
Volume + / SRS Key
Status Indicator
Multi-function Button (MFB) / Play / Pause
Rewind I
I
Fast Forward
Volume
Microphone
USB Charging Socket (open the cover)
4
6
1
2
3
I
Bluetooth Specification:
Bluetooth Profiles Supported:
Range of Frequency:
Operating Distance:
Charging Time:
Talk Time*:
Music Playing Time*:
Standby Time*:
Dimensions:
Weight:
BlueBAND Sport Overview
8
5
7
* may vary due to users’ operation mode and mobile phone settings
Getting Started
3
Before using your BlueBAND Sport (“headphones”) for the first time, please ensure that
1. the headphones are fully charged;
2. the fully charged headphones must be paired and connected with a Bluetooth mobile
phone.
Charging Your Headphones
Pairing Your Headphones with a Bluetooth Mobile Phone
The headphones come with a built-in rechargeable battery. Prior to using the headphones for
the first time, you are recommended to fully charge the battery.
Pairing is only required the first time you use the headphones. Please refer to your mobile
phone user guide for pairing instructions.
1) Ensure the headphones are off.
2) To activate the pairing mode, press and hold the headphones’ MFB for 8 seconds without
releasing your finger until its status indicator flashes blue and red light alternately.
3) Activate your mobile phone’s Bluetooth, search Bluetooth devices, select “BlueBAND
Sport” and enter the password “8888”. When the pairing is completed, the headphones’
status indicator will flash blue light rapidly for five times.
If the pairing cannot be completed within 3 minutes after the pairing mode has been activated,
the headphones’ status indicator will flash purple rapidly for five times and then turns off.
Repeat steps 1 to 3 to pair both devices again.
Use only the supplied charger to charge the headphones.
Status
• Charging
• Fully charged
• Low battery
• Out of battery
Status Indicator
• Red light
• Blue light
• Flashing red light
• The light goes off
Audio
• a short beep every 1 minute
● 3 hours are required to fully charge the headphones.
● Charging indication will be delayed for a few seconds if the headphones have not been used
for a long time or the battery is drained.
5
6
Using Your Headphones
Turning Your Headphones On and Off
Call Functions
Function
Turn on
Button
Audio
Status Indicator
Press and hold the
a short beep
Flashing blue light for 3 times
MFB for 2 seconds
When you turn on your headphones for the first time, the headphones
automatically enter the pairing mode, i.e. the status indicator flashes blue and
red alternately. This allows you to immediately pair your headphones and mobile
phone. Please refer to “Pairing Your Headphones with a Bluetooth Mobile Phone”.
Turn off
Press and hold the
a long beep
Red light for 2 seconds and
MFB for 2 seconds
then the light goes off
Function
Button
Answer a call
Press the MFB once
Audio
Status Indicator
Flashing purple light
End a call
Adjust Volume
Press the MFB once
Press the Volume + / Volume
once to increase / decrease by 1
step (Total 8 levels)
Flashing blue light
Flashing blue light
Press
once
a short beep Flashing blue light
Voice Dialing
say the voice tag as soon as you hear the short beep and you must have recorded the voice
tag into your mobile phone
● If your headphones are paired with your mobile phone, press the MFB once more
after you turned on the headphones to re-connect the mobile phone and
headphones.
● If you do not plan to use the headphones for a while, you are recommended to turn
off the Bluetooth function of your mobile phone.
Last No. Redial
Double click
Call Waiting
Call Reject
Press the MFB once
Press and hold either volume key
for 2 seconds
Call Transfer
(headset to mobile phone)
While speaking, press and hold
either volume key for 2 seconds
Call Transfer (mobile phone While speaking, press
back to headset)
7
Flashing blue light
once
a short beep Flashing blue light
Flashing blue light
Flashing blue light
8
Using Your Headset (cont’d)
Resetting Your Headphones / Removing the Pairing History
Music Playing Functions (A2DP and AVRCP Applicable Only)
Function
Button
Audio
Disable SRS
(the default is SRS ON)
When playing music, press and hold a short beep
the Volume + for 2 seconds
Enable SRS
same as "above"
Answer a call when playing
music
Press the MFB once
Flashing purple light
when there is a call
End a call and resume music Press the MFB once
Press‟II once
Play
Flashing blue light*
Flashing blue light*
You may reset the headphones to its default settings. Resetting will also remove the pairing
settings of your headphones with the mobile phone.
Status Indicator
1. Connect the supplied charger to your headset and then to AC power. The status indicator will
stay red.
2. Press and hold the Volume + for 10 seconds until the status indicator flashes purple.
3. Release the Volume + .
4. Press and hold the Volume + again until the status indicator flashes purple and then release
the Volume + .
5. The status indicator will stay red again and the headphones are reset.
Flashing blue light
once
2 short beeps Flashing blue light
twice
Pause
Press‟II once
Fast Forward
Press and hold
Next Track
Rewind
Replay
Press ‟ I once
Press and hold I
Press I‟ once
Flashing blue light*
Flashing blue light*
Flashing blue light*
Adjust Volume
Press the Volume + / Volume
once to increase / decrease by 1
level (Total 8 levels)
Flashing blue light*
i.Tech Bluetooth headset is designed to work with Bluetooth devices. Due to large
variability between different Bluetooth devices from different manufacturers,
interoperability between the headset and all Bluetooth-enabled products is not
guaranteed.
Flashing blue light*
I
Flashing blue light*
9
10
Troubleshooting
Safety Information
I can't hear anything in my headphones.
• Ensure the headphones are turned on and are properly charged.
• Ensure the headphones are properly paired with the mobile phone.
• Make sure that the mobile phone is connected with the headphones – if it does not
connect, either refer to the mobile phone's Bluetooth menu or by pressing the MFB once
(see “Turning Your Headphones On and Off” and “Pairing Your Headphones with a
Bluetooth Mobile Phone”).
I can't connect my headphones with mobile phone.
• Ensure your headphones are turned on and are properly charged.
• Ensure the headphones are properly paired with your mobile phone.
• Ensure your mobile phone’s Bluetooth feature is activated. Please refer to your mobile
phone user guide for specific instruction.
• Ensure the headphones are within ten metres range of your mobile phone and there are
no obstructions, such as walls or other electronic devices in between.
If the above steps do not solve your problem, please recharge the headphones and remove
your mobile phone’s battery for a while.
I can’t turn off the headphones.
Recharge the headphones for two seconds then disconnect the charger from the
headphones. The headphones now turn off.
11
• Check and observe local laws regarding the use of a mobile phone and headphones while
driving. If you use the headphones while driving, ensure your full attention and focus. It
is your responsibility to drive safely. Consider to pull off the road before making or
answering a call.
• Never leave your headphones above any air bag deployment area inside your car as
serious injury may result when an air bag deploys.
• Never allow children to play with the headphones – small parts may be of choking hazard.
• Observe all signs and displays that require an electrical device or RF radio product to be
switched off in designated areas. These could include hospitals, blasting areas, and
potentially explosive atmospheres.
• Turn off your headphones prior to boarding an aircraft. Do not use your headphones
inside an aircraft.
• To prevent damage to your hearing, please do not set the listening volume too high.
• Do not attempt to modify the headphones.
• Never use the headphones while taking a bath.
• Do not use the headphones in a sauna or steam room.
• Do not keep the headphones near a wash basin or other wet places.
• Do not use the headphones outdoors in the rain.
• Do not use the headphones in stormy weather.
• Do not clean the headphones while they are being charged. Always disconnect the
charger from the headphones before cleaning.
• Do not attempt to force open the built-in battery.
• Dispose of the battery and the headphones according to local regulations. Do not dispose
of them as household waste.
12
*If SRS is enabled, the status indicator will flash blue light twice every time.
FCC RF Radiation Exposure Statement:
Care and Maintenance (cont’d)
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
• Only charge the headphones built-in battery in accordance with the instructions described in
this user guide.
• Avoid charging the headphones in extremely high or low temperatures.
• Do not connect the headphones to the charger while on an active call.
Built-in Battery
• Do not attempt to replace the headphones‘ battery as it is in-built and is not changeable.
• Dispose of the battery according to local regulations. Do not dispose of the battery as
household waste.
• Charge the battery in accordance with the instructions supplied with this user guide.
• Use only the charger supplied by the headphones’ original manufacturer to charge the
battery.
Charger
• Use only the charger supplied by the headphones’ original manufacturer to charge the
headphones. Other chargers may look similar but using them could be dangerous and could
damage the headphones.
• Do not attempt to disassemble the charger as it may expose you to dangerous voltages or
other risks. Incorrect reassembly can cause electric shock when the headphones are
subsequently used.
• Do not use the charger outdoors or in damp areas.
Care and Maintenance
headphones
• Turn off your headphones before placing it in your pocket or bag. If the MFB is accidentally
depressed, your mobile phone may place an unintended call.
• Do not expose the headphones to liquid, moisture or humidity, or rain as it is not waterproof.
• Do not use abrasive cleaners to clean the headphones.
• Do not expose the headphones to extremely high or low temperatures.
• Do not leave the headphones in direct sunlight for an extended period of time.
• Do not leave the headphones near open flames such as cooking burners.
• Do not dispose of the headphones in a fire as it will result in explosion.
• Do not bring the headphones into contact with any sharp objects as this will cause scratches
and damages.
• Do not stick anything inside the headphones as this may damage internal components.
• Do not attempt to disassemble the headphones as they do not contain serviceable
components.
• If you do not plan to use the headphones for a long period, please store them in a dry place
that is free from extreme temperatures and dust.
13
14
Declaration of Conformity
Federal Communications Commission (FCC) Statement
We, i.Tech Dynamic Limited, declare that the following product:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Product Name: i.Tech BlueBAND Sport
Model No.: C51-B08003-XX
is in conformity with the following essential requirements of Council Directive 1999/5/EC
(referred to as R&TTE Directive): Article 3.1a, 3.1.b and 3.2. and the product is manufactured
in accordance with Annex II of the above directive.
A copy of the Declaration of Conformity can be found at http://www.itechdynamic.com.
i.Tech declares under our sole responsibility that the headset is in conformity with the
provisions of the following Council Directives: 1999/5/EC.
Notes on Environmental Protection
After the implementation of the European Directive 2002/96/EU in the national legal system,
the following applies: Electrical and electronic devices must not be disposed of with domestic
waste. Consumers are obliged by law to return electrical and electronic devices at the end of
their service lives to the public collection points that are set up for this purpose or designated
points of sale. However, such details are defined by the national law of the respective country.
This symbol on the product, the instruction manual or the packaging indicates that the product
is subject to these regulations. By recycling, reusing the materials, or other forms of utilizing
old devices, you are making an important contribution in protecting our environment.
15
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
16
2008 Hutchison Harbour Ring Enterprises Limited
All rights in this publication are reserved and no part may be reproduced without the prior
written permission of the publisher. The contents of this publication are believed to be correct
at the time of going to press, but any information, specifications, products or services
mentioned, and product I.D. shown may be modified, supplemented or withdrawn without
further notice.
The Stylized i.Tech logos are trademarks owned by Hutchison Harbour Ring Enterprises
Limited or its affiliates. All other trademarks or registered trademarks belong to their
respective owners.
Dispose of the packaging and this product in accordance with the latest provisions.
is a trademark of SRS Labs, Inc. WOW HD technology is incorporated under license from SRS Labs, Inc.
04/2008
17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising