KitchenAid Ventilation Hood KHTU705R User manual

KitchenAid Ventilation Hood KHTU705R User manual
®
30” and 36” Range Hoods
OVERALL DIMENSIONS
PRODUCT MODEL NUMBERS
KHTU705R
KHTU765R
KHTU705S
KHTU765S
5 ⁷⁄₈" (14.9 cm) dia.
exhaust collar
Electrical: 120-V, 60-Hz, AC-only, 15 amp.
electrical supply. Use copper wire only. A timedelay fuse or circuit breaker and separate circuit is
recommended.
Interchangeable
front trim
9 ¹⁵⁄₁₆"
(25.2 cm)
20 ³⁄₁₆”
(51.3 cm)
INSTALLATION CLEARANCES
29 ¹⁵⁄₁₆” (76.0 cm) - 30” (76.2 cm) model
35 ¹⁵⁄₁₆” (91.3 cm) - 36” (91.4 cm) model
VENT AND ELECTRICAL OPENINGS AND MOUNTING
SCREW LOCATIONS
1¹⁄₄”
(3.2 cm)
30”(76.2 cm) or
36” (91.4 cm) min.
cabinet opening width
Centerline of
exhaust collar
5⁷⁄₈”
(14.9 cm)
dia.
9¹⁄₈”
(23.2 cm)
1³⁄₁₆”
(3.0 cm)
1⁵⁄₁₆”
(3.3 cm)
24” (61 cm) min.
30” (76.2 cm)
suggested max.
bottom of hood
to cooking surface
18” (45.7 cm)
min. clearance
upper cabinet
to countertop
3⁵⁄₁₆”
(10.0 cm)
1⁵⁄₁₆”
(3.3 cm)
7¹⁄₂”
(19.0 cm)
70 ⁵⁄₁₆"
(178.6 cm)
min.
76 ⁵⁄₁₆"
(193.8 cm)
max.
to bottom of
cabinet frame
Centerline of
hood
Electrical
knockouts
VENTING REQUIREMENTS
This range hood is factory set for vented installations. Vent system
can terminate through either the roof or a wall. The vent system
length should not exceed 35 ft (10.7 m)
It is recommended that you use round vent instead of rectangular
vent, especially if elbows are required.
36” (91.4 cm)
countertop
height
For best performance, use no more than three 90° elbows. If more
than one elbow is used, make sure that there is a minimum of 24
inches (61 cm) of straight vent between any two elbows. Do not
install two elbows together.
To calculate the length of system you need, add the equivalent
feet (meters) from chart below for each vent piece that will be
needed.
Determine the length of the vent system you need
To calculate the length of the vent system you need, add the
equivalent feet (meters) from chart below for each vent piece that
will be needed.
Recommended standard 6” (15.2 cm) fittings
1 ft. round=
1 ft. (0.3 m)
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
90° elbow=
5 ft. (1.5 m)
45° elbow=
2.5 ft. (0.8 m)
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 9763384
09-11-06
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement