Grizzly Home Security System G9960, G9960 Owner's manual

Grizzly Home Security System G9960, G9960 Owner's manual
 Industrial, /, Inc.
MODEL G9960
COPYRIGHT©2000 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN.
TABLE OF CONTENTS
Table Of Contents PAGE
1. Safety
Safety instructions for power tools .=======—— on. ]] 7" 1-2
Additional safety instructions for grinders «coe ernennen 3
2. Circuit requirements
110V Operation ER CI Ne 4
FUSING ==oon oe NIN NA só 4
Extension COords ----------.-==.e.e.eeeeeeerreceereee reee reee sess eeeececereceeereeccen cerrar. 4
Grounding eme ee eta RE a RARA. 4
3. Introduction
Commentary ВН 5
Getting to know your grinder --------------------===——emeeeeesennn enanos 6
Specifications II EN 7
Operating instruchione "azar EIA 8-12
How to adjust the cooling ERLE rss sms ssa 8
How to change the grinding wheels ------....-.-..........mme.eecceec ene. 8
How to dress the grinding WHEREIS armements 9
How to sharpen planer/ jointer knives ===... 40-11
Ном 10 [email protected] CNÏSO\S. m……rmmeementmeenmennennnansts dissem 11
How to sharpen drill bits ssa msm 12
Warranty and returnS …….….……….…..….….….….….……eeeenennensnenennennen 13
Parts ©Пасгат ...............есеоноонононененннененененнннннннененннненененнненненененеененененнненененнненнннне: 14
Parts. ISE... EE 15
G9960 Wet & Dry Cutting Tool Grinder
SECTION 1:SAFETY
AWARNING
For Your Own Safety Read Instruction
Manual Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous conditions. this
manual uses a series of symbols and signal words which are intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
ADANGER
AWARNING
A CAUTION
NOTICE
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to
alret against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the equipment.
AWARNING
Safety Instructions For Power Tools
. KEEP GUARDS IN PLACE and in working
order.
. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and
adjusting wrenches are removed from tool
before turning on.
3. KEEP WORK AREA CLEAN. Cluttered areas
and benches invite accidents.
. DON’T USE IN DANGEROUS ENVIRON
MENT. Don’t use power tools in damp or wet
locations, or where any flammable or noxious
fumes may exist. Keep work area well lighted.
. KEEP CHILDREN AND VISITORS AWAY. All
children and visitors should be kept a safe
distance from work area.
. MAKE WORK SHOP CHILD PROOF with
padlocks, master switches, or by removing
starter keys.
. DON'T FORCE TOOL. It will do the job
better and safer at the rate for which it was
designed.
. USE RIGHT TOOL. Don't force tool or attach-
ment to do a job for which it was not designed.
G9960 Wet & Dry Cutting Tool Grinder
9.
10.
11.
AWARNING
Safety Instructions For Power Tools
USE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition.
Conductor size should be in accordance with
the chart below. The amperage rating should
be listed on the motor or tool nameplate. An
undersized cord will cause a drop in line volt-
age resulting in loss of power and overheat-
ing. Your extension cord must also contain a
ground wire and plug pin. Always repair or
replace extension cords if they become
damaged.
Minimum Gauge for Extension Cords
LENGTH
AMP RATING | 25ft | 50ft | 100ft
0-6 18 16 16
7-10 18 16 14
11-12 16 16 14
13-16 14 12 12
17-20 12 | 12 10
21-30 10 | 10 No
WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings, bracelets,
or other jewelry which may get caught in
moving parts. Non-slip footwear is recom-
mended. Wear protective hair covering to
contain long hair.
ALWAYS USE SAFETY GLASSES. Also use
face or dust mask if cutting operation is
dusty. Everyday eyeglasses only have impact
resistant lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold
work when practical. It’s safer than using your
hand and frees both hands to operate tool.
13.
14.
13.
16.
DON’T OVERREACH. Keep proper footing
and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools
sharp and clean for best and safest perfor-
mance. Follow instructions for lubricating and
changing accessories.
DISCONNECT TOOLS before servicing and
changing accessories, such as blades, bits,
cutters, and the like.
REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in off posi-
tion before plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult
18.
М.
the owner's manual for recommended acces-
sories. The use of improper accessories may
cause risk of injury.
CHECK DAMAGED PARTS. Before further
use of the tool, a guard or other part that is
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function. Check for align-
ment of moving parts, binding of moving
parts, breakage of parts, mounting, and any
other conditions that may affect its operation.
A guard or other part that is damaged should
be properly repaired or erplaced.
NEVER LEAVE TOOL RUNNING UNAT-
TENDED. TURN POWER OFF. Don't leave
tool until it comes to a complete stop.
G9960 Wet & Dry Cutting Tool Grinder
AWARNING
Additional Safety Instructions For Grinders
. Wear a face shield and/or safety goggles.
. Use clamps and supports to sharpen tools.
. Grinding creates sparks. make sure your
work area is free of combustible materials.
. Dress the grinding wheel when its surface
becomes rutted or uneven. Replace the
wheel if the wear or damage becomes
excessive.
. Do not use a wheel that is cracked or chipped.
. Be sure the grinder is mounted on a stable
surface.
. If you are unclear about operating the
machine, don’t do it. Please call our service
department if you have questions about any
element of this machine’s operation.
. Use care when handling sharpened cutting
tools.
AWARNING
Like all power tools, there is danger associ-
ated with the Model G9960 Universal Knife
Grinder. Accidents are frequently caused
by lack of familiarity or failure to pay
attention. Use this tool with respect and
caution to lessen the opssibility of operator
injury. If normal safety precautions are
overlooked or ignored serious personal
injury may occur.
A CAUTION
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious
personal injury, damage to equipment or
poor work results.
AWARNING
Operating this equipment has the potential
for flying debris to cause eye injury.
Always wear safety glasses or goggles
when operating equipment. Everyday glasses
or reading Glasses only have impact resis-
tant lenses, they are not safety glasses.
Be certain the safety glasses you wear
meet the appropriate standards of the
American National Standards Institute (ANSI).
G9960 Wet & Dry Cutting Tool Grinder
SECTION 2: CIRCUIT REQUIREMENTS
110V Operation
The Model G9960 is wired for 110/120V, single
phase operation only. The 12 HP, 3450 RPM
motor draws 8 amps. This is not a large load.
However, if you operate the grinder on a circuit
that is already close to capacity, it could over-
load that circuit. If an unusual load does not
exist and a power failure still occurs, contact a
qualified electrician or our service department.
Grounding
In the event of an electrical short, grounding
reduces the risk of electric shock by providing a
path of least resistance to disperse electric
current. This tool is equipped with a power cord
having an equipment-grounding conductor. The
outlet must be properly installed and grounded in
accordance with all local codes and ordinances.
Fusing
A 15-amp fuse or circuit breaker should be used
when fusing the wet & dry cutting tool grinder.
Circuits rated any higher are not adequate to
protect the motor from power surges.
Equipment returned to us for service that shows
evidence returned to us for service that shows
evidence of being over-fused will be repaired or
replaced totally at the customer's expense, regard-
less of the present warranty status.
AWARNING
This equipment must be grounded. Verify
that any existing electrical outlet and circuit
you intend to plug into is actually grounded.
If it is not, it will be necessary to run a
separate 12 A.W.G. copper grounding wire
from the outlet to a known ground. Under
no circumstances should the grounding pin
from any three-pronged plug be removed.
Serious personal injury may occur.
Extension Cords
If you find it necessary to use an extension cord
with the Model G9960 make sure the cord is
rated Hard Service (grade S) or better. Refer to
the chart in the standard safety instructions to
determine the minimum gauge for the extension
cord. The extension cord must also contain a
ground wire and plug pin. Always repair or
replace extension cords when they become worn
>>.
o
Current | NY
Carrying | |
Prongs ъ
Grounded Outlet Box
i
/
7
= > y
ВЯ 5 Va / | pre nn #
|
N / nn S | |
\ A, |
Na AO
> NA UN und ) |
NW
Grounding Blade Is —
Longest Of the Three Blades
Figure 1. Grounded plug configuration.
or damaged.
©
G9960 Wet & Dry Cutting Tool Grinder
SECTION 3: INTRODUCTION
Commentary
We are proud to offer the Grizzly Model G9960
wet & dry cutting tool Grinder. The Model
G9960 is part of a growing Grizzly family of fine
woodworking machinery. When used according
to the guidelines set forth in this manual, you
can expect years of trouble-free, enjoyable oper-
ation and proof of Grizzly's commitment to
customer satisfaction.
The Model G9960 is designed for heavy-duty
professional use. It features a capacitor-start 12
HP motor that operates on 110V at 3450 RPM. lt
IS capable of sharpening jointer and planer
knives up to 24" long. Its work table adjusts
from O° to 90° to accommodate a wide range of
cutting angles. Overall shipping weight of the
Model G9960 is approximately 180 Ibs.
A number of optional accessories for the Model
G9960 are available through the Grizzly cata-
log. They include a diamond dressing tool ana
replacement stones in green color silicon carbide
grinding wheel.
We are also pleased to provide this manual with
the Model G9960 it was written to guide you
through assembly, review safety considerations,
and cover general operating procedures. It repre-
sents our effort to produce the best documenta-
tion possible. If you have any comments regard-
ing this manual, please write to us at the
address below:
Grizzly Industrial, Inc.
¢ Technical Documentation
Р.О. Вох 2069
Bellingham, WA 98227-2069
G9960 Wet & Dry Cutting Tool Grinder
Most importantly, we stand behind our machines. If
you have any service questions or parts
requests, please call or write us at the location
listed below.
Grizzly Industrial, Inc.
2406 Reach Road
Williamsport, PA 17701
Phone: (570) 326-3806
Fax: (800) 438-5901
E-Mail: [email protected]
Web Site: http/www.grizzlyindustrial.com
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G9960 as supplied when the manual was
prepared. However, owing to Grizzly's policy of
continuous improvement, changes may be made
at any time with no obligation on the part of Griz-
zly. Whenever possible, though, we send manual
updates to all owners of a paricular tool or
machine. Should you receive one, we urge you
to insert the new information with the old and
keep it for reference.
A CAUTION
To operate this, or any power tool, safely
and efficiently, it is essential to become as
familiar with its characteristics as possible,
The time you invest before you begin to
use your Model G9960 will be time well
spent. DO NOT operate this machine until
you are completely familiar with the contents
of this manual. Make sure you read and
understand all of the safety procedures. If
you do not understand something, DO NOT
operate the machine.
©
GETTING TO KNOW YOUR GRINDER
TRAVERSE HANDLE TABLE UP & DOWN ADJUSTMENT
(FROM RIGHT TO LEFT) HANDWHEEL
6" CUP GRINDING WHEEL
COOLING WATER ig .
KNIFE HEIGHT ADJUSTMENT KNOBS
KNIFE PLATE
Ue >, ла :
KNIFE SU PPORTS \ a
WORK PLATE Abe и es -
(ADJUSTABLE Ea <; = ui
ÉL:
na ADJUSTMENT KNOBS
KNIFE BACK 8: FORTH
ADJUSTMENT HANDWHEEL
? >,
E neveu COOLING
A WATER POT
WORK TABLE
RUGGED 1/2HP MOTOR
CABINET STAND
DIAMOND DRESSER TOOLS _ Ls
DRESSING STICK
DRILL BITS SUPPORTS
“B= G9960 Wet & Dry Cutting Tool Grinder
SPECIFICATION
SPECIFICATION
Maximum Knife Length 5/5 000 SE TE ETES EC EE au 24"
Maximum Drill Grinding Attachment Capacity TP REC 5/8"
Maximum Chisel Width ER CRD ARA AAA EEG i a ee 4"
Straight Cup Grinding Wheel Dimensions «tse, 6"X1 1/2 "X5/8"
Grinding Wheel Rotation Speed (R.P.M) CEE Eee Ease EEE EEE Eee seas Ne OREA anecooededasmedo, 3450
Work Plate Adjustment EII EII CECI AIRES CNA Em mi am Ee a 0"—90"
Knife Support Traverse Length RRA AE aa ea sue 25"
Cooling Water Pot Capacity LO EEC CARA AAA a Rs 0.751
[МО{ог «vr remem A A AA AA AAA NI aaa aster a tees rasan renner nen 1/ HP, 1 PH
Machine Dimensions (L X W X H) NA EEN TA EE ET 18"X25"X50"
Packing Dimensions (L X W X H) --Machine---16.5"X16.5"X16.5" Stand 15.5"X15.5"X29"
Weight-net/gross ---- Machine -- 40/42 KGS Stand === 38/40 KGS
Remove all items from the carton. Check the TOOLS NEEDED:
items received against the exploded. view draw- 10 m/m Wrench
ing in the back of the manual. If any items are 12 m/m Wrench
missing or were damaged in shipment, lease 14 m/m Wrench
contact us. 3 m/m Allen Wrench
5 m/m Allen Wrench
6 m/m Allen Wrench
NOTICE
A full parts list and breakdown can be
found toward the end of this manual. For
easier assembly, or to identify missing
parts, please refer to the detailed illustra-
tions at the end of the manual.
Rose color aluminum oxide grinding wheels.
Suitable for grinding high tensile material
such as hish speed steel.
STANDARD ACCESORES:
Greed color silicon carbide grinding wheels.
For special alloy grinding such as tungsten
carbide.
OPTIONAL ACCESORES:
G9960 Wet 8: Dry Cutting Tool Grinder
OPERATING INSTRUCTIONS
ADJUST THE COOLING WATER.
+ After the motor starts, turn on the cooling water control knob
to provide a drop of water every few seconds.
- Be aware that the cooling water must be rust-proofed and do
not use too much cooling water. One pot of cooling water
can be used for three to four hours.
©
CHANGE GRINDING WHEELS.
Loosen and remove the cover plate using a phillips head screw-
driver.
Loosen and remove the grinding wheel flange using a 5 m/m
allen wrench.
Remove grinding wheel, replace with new wheel. Remount flange
and socket cap screw and tighten with a 5 m/m allen wrench.
A CAUTION
Never allow visitors into your shop while
assembling, operating, or maintaining tools
and machinery. Keep your shop child-safe
by locking up securely when not in use,
and by providing proper supervision when
children are present.
©
G9960 Wet & Dry Cutting Tool Grinder
OPERATING INSTRUCTIONS
DRESSING THE GRINDING WHEEL.
After a period of usage, the grinding wheel surface will become
loaded and need to be dressed.
To dress the wheel follow the steps outlined below.
A. DRESSING THE SURFACE.
1. Remove the knife support assembly and fix diamond dresser
tools onto the work plate and adjust the angle to horizontal 0
degree.
2. Use up 8 down handwheel to adjust work table until the
diamond dresser just touches the surface of grinding wheels.
3. With machine running push the handle of the diamond dresser
tool back & forth to dress surface of grinding wheel until the
wheel is completely dressed.
B. DRESSING THE EDGE. DIAMOND DRESSER A $ E
1. Remove the knife support assembly and fix diamond dresser \\\ E E £ i
tool onto the work plate and adjust the angle to vertical 90 \ ея Ц,
degree. ml)
2. Use backward & forward handwheel to adjust work plate until |
the diamond dresser just touches the edge of the grinding se «WC:
wheel. - =
3. With machine running push the handle of the diamond dresser "A
tool up & down to dress edge of grinding wheel until the
wheel is completely dressed.
©
Dressing Stick — most popular general purpose dresser for use DRESSING STICKs
on emery wheels. > = ‘[ r
SURFACE 8: EDGE CUTTING OF THE GRINDING WHEELS.
Use the surface and edges of the grinding wheels. To sharpen
both sides of the knife without detaching the knife.
A CAUTION
KNIFE
SURFACE CUTTING
Planer, jointer and other knives are
|
: EDGE | | |
dangerously sharp. Use extreme caution, CUTTING | | |
particularly after sharpening. Failure to TT
exercise care while working near knives
could result in severe injury. |
©
G9960 Wet & Dry Cutting Tool Grinder =D
GRINDING WHEEL
OPERATING INSTRUCTIONS
MOUNTING JOINTER/PLANER KNIVES.
1. Remove the knife lock top plate. Place the dressing tool guide
along the front edge of the knife support plate. Adjust the
height adjustment knobs until each height adjustment screw
just touch the dressing tool guide.
2. Place the knife (beveled edge down) onto the knife support,
firmly against the height adjustment screws. Place the knife
lock plate onto the knife support and firmly tighten the locking
knobs.
NOTE: The knife must be firmly mounted against the height
adjustment screws, double check at this time.
KNIFE LOCK PLATE
HEIGHT ADJUSTMENT SCREW
KNIFE SUPPORT KNIFE LOCK PLATE
A CAUTION
Planer, jointer and other knives are
dangerously sharp. Use extreme caution,
particularly after sharpening. Failure to
exercise care while working near knives
could result in severe injury.
4
a
№
ADJUST THE KNIFE TO THE CORRECT RELIEF & |
INCLUDED ANGLE. a #
On most tools it is easy to determine the correct relief KNIFE ANGLE Y ——
and included angle. However on planer and jointer 5
knives there is a wide range of ‘correct’ relief ana ENCLUDED ANGLE
included angles. The included angle on a planer knife
can vary from 30 to 60.
The woodworker is faced with hundred of varieties of
woods, different moisture content and hundreds of
molding and planing applications. All these factors can
alter the relief and included angles found on planer and
jointer knives.
A
CUTTER HEAD
MATCH TO THE EXISTING INCLUDED ANGLE.
With such a wide variety of accepted angles, it would > y
not be wise to change the included angle to a predeter-
mined setting. The best thing to do is match to the INCORRECT-SCRATCH MARKS ALONG TOP OF BEVEL EDGE
existing included angle already on the knife. Mark the
beveled edge of the knife with a red marker. As a start- —
ing point rotate the pivot plate knob until the knife is [ — A
held at a 30 angle. Rotate the grinding wheel hand-
wheel until the wheel just touches the knife. With the
motor off turn the grinding wheel by hand against the
INCORRECT-SCRATCH MARKS ALONG BOTTOM OF BEVELED EDGE
knife surface adjust the pivot plate until the grinding == = \
wheel will leave marks all the way across the knife —— ZZ = 4
edge. CORRECT-SCRATCH MARKS ALL THE WAY ACROSS BEVELED EDGE
-10- G9960 Wet & Dry Cutting Tool Grinder
OPERATING INSTRUCTIONS
SHARPEN JOINTER/PLANER KNIVES GRINDING THE
KNIFE.
When facing the machine traverse the knife support assembly
from the right to the left. Continue to make passes until the
knife is sharp and all nicks are removed.
A CAUTION
Use extreme caution when working near
cutting surfaces. Failure to exercise care
while working near knives could result in
severe injury.
©
SHARPENING CHISELS. UN. CHISEL SUPPORT
- Remove the knife support assembly and place the chisel | Om Ty N
support assembly onto work plate. ©
+ Fix chisels onto the chisel support, adjust and experiment 5
with the pivot rotate knob rotate knobs until you have the
best supporting angle.
- Adjust the table lower until the chisels just touch the surface
of the grinding wheels.
- When facing the machine traverse the chisel support assem
bly from the right to the left continue to make passes until
the chisel is sharpened and all nicks are removed.
\ NE ps
© x EW CHISEL SUPPORT
% $ o
CHISEL ,
G9960 Wet & Dry Cutting Tool Grinder
OPERATING INSTRUCTIONS
A
10.
IL
12.
13.
SHARPENING DRILL BITS
drill sharpening fixture is included with the G9960 Knife
Grinder. The instructions below describe the method for grinding
1184 the most common angle. Other angles may be produced.
Consult the proper literature for more information.
1.
Remove the knife support assembly and attach the drill grind-
ing fixture onto the knife support rest using the two hex head
screws provided. The fixture has a pair of slender keys on
one face. Make sure this face is positioned toward the opera-
tor.
. Turn the front handwheel until the knife support rest moves
furthest from the grinding wheel.
. Move the table elevation until it is positioned at the highest
possible point. Secure the drill bit into the chuck with the
chuck key. Place the drill chuck and drill into the fixture.
. The keys on the grinding fixture will fit into the cogs on the
drill chuck body. Allow them to engage and rotate chuck body
counter-clockwise until it stops. Lift drill chuck and turn until
one chisel edge of the drill bit is straight down. Allow the keys
and cogs to engage.
. Look at one of the keys in the grinding fixture and use it as a
pointer for the degree scale on the side of the drill chuck.
Note the angle indicated and write it down for future reference.
. Loosen the lock knobs and change the angle of the knife
support rest to 594 as indicated on the scale. Retighten
knobs.
. Lower the table until the drill bit just touches the grinding
wheel and adjust table down 1/2 turn.
. Rotate the drill chuck clockwise until it stops.
. Start grinder motor. Slowly lower table until grinding wheel
contacts drill bit.
Rotate drill chuck counter-clockwise until it stops. The bit will
contact the grinding wheel on the back surface first and as it
rotates, grind up to the chisel cutting edge. Do Not leave drill
bit in this position. Rotate drill chuck clockwise to the begin-
ning position. Repeat until drill bit is no longer ground by grind-
ing wheel.
Pull drill chuck from grinding fixture and turn off grinder.
When grinding wheel comes to a complete stop, reinsert the
drill chuck. Find the number on the degree scale that is 1804
from the first indicated setting. Engage the keys and cogs.
Rotate the drill chuck counter-clockwise until its stops.
Lift drill chuck slightly and start grinder motor. Allow drill
chuck to contact grinding wheel and repeat step 10.
©
CHUCK
DEGREE MEASURE
Eee pose
-12-
G9960 Wet & Dry Cutting Tool Grinder
PARTS DIAGRAM
G9960 Wet & Dry Cutting Tool Grinder
-14-
PARTS LIST
DESCRIPTION QTY DESCRIPTION QTY
1 KNOB 1 47 THRUST BEARING 2
2 HEX JAM NUT 1 48 HAND WHEEL 1
3 SOCKET SET SCREW 3 49 PHILLIPS HEAD SCREW 2
4 DIAMOND DRESSER LOCK PLATE 1 50 WATER POT 1
5 DIAMOND DRESSER 1 51 HEX CAP SCREW 2
6 HEX CAP SCREW 6 52 WATER POT SUPPORT 1
7 WASHER 10 53 KNOB 1
8 DIAMOND DRESSER SUPPORT 54 PHILLIPS HEAD SCREW 2
9 CHUCK HOLDER SUPPORT 55 KNOB 1
10 CHUCK HOLDER 56 WASHER 1
11 CHUCK 57 HOSE SUPPORTER 1
12 KNOB 58 WHEEL GUARD 1
13 HEX NUT 59 SOCKET CAP SCREW 1
14 CHISEL LOCK PLATE 60 OUTER FLANGE 1
15 CHISEL SUPPORT 61 6" GRINDING WHEEL 1
16 ROUND HEAD SCREW 62 INNER FLANGE 1
17 HANDLE 63 PHILLIPS ROUND HEAD SCREW 2
18 KNIFE LOCK PLATE 64 GRINDING WHEEL HOUSING 1
19 KNOB 65 SOCKET CAP SCREW 4
20 O-RING 66 SPRING WASHER
21 KNOB 67 WASHER
22 KNIFE SUPPORT 68 WORK TABLE
23 WORK PLATE 69 T-THREAD SCREW
24 PIVOT KNOB 70 UPPER & DOWN SLIDE GUIDE BASE
25 PIVOT ROTATE KNOB 71 UPPER & DOWN SLIDE GUIDE
26 WORK BRACKET BASE 72 PLATE
27 HEX CAP SCREW 73 HEX CAP SCREW
28 HEX NUT 74 HEX CAP SCREW
29 SPRING WASHER 75 HEX CAP SCREW
30 PLATE 76 PHILLIPS ROUND HEAD SCREW
п — © — 2 PEON 2 ln © N A| OO =D == O00 = NN № + BD AA — —
31 COVER PLATE 77 MOTOR
32 PHILLIPS HEAD SCREW 78 HEX CAP SCREW
33 HEX CAP SCREW 79 MOTOR COVER
34 WASHER 80 SWITCH
35 HEX CAP SCREW 81 POWER CARD
36 PHILLIPS HEAD SCREW 82 CORD BUSH
37 POINTER 83 HEX CAP SCREW
38 WASHER 84 WASHER
39 HEX CAP SCREW 85 BASE
40 PHILLIPS HEAD SCREW 86 ROD WATER POT SUPPORT
41 ANGLE ADJUSTING BASE 87 RECYCLE WATER POT SUPPORT
42 T-THREAD UNT 88 RUBBER SUPPORT FEET
43 SLIDE GUIDE 89 HEX CAP SCREW
44 PHILLIPS ROUND HEAD SCREW 90 CABINET STAND
45 T-THREAD SCREW 91 WASHER LOMM
46 BEARING BASE 92 HEX JAM UNT
G9960 Wet & Dry Cutting Tool Grinder
-15-
G9960 Wet & Dry Cutting Tool Grinder
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This 1s Grizzly s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spe-
cial, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a Return Number , which must be clearly posted on the outside as well as the inside of the car-
ton. We will not accept any item back without this number. Proof of purchase must accompany the mer-
chandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
-13-
WARRANTY CARD
Name
Street
City
State Zip
Phone Number E-Mail
FAX
MODEL #G9960 24" Wet & Dry Cutting Tool Grinder
Order #
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of
course, all information is strictly confidential.
1. How did you learn about us?
_ Advertisement ___ Friend
___ Catalog ___ Card Deck
__ World Wide Web
-—. Other
2. Which of the following magazines do you subscribe to.
American Woodworker
___Cabinetmaker
___Family Handyman
___Fine Homebuilding
___Fine Woodworking
___Home Handyman
— Practical Homeowner
_— Shop Notes
— Today s Homeowner
_— WOOD
— Wooden Boat
___Woodshop News
___Journal of Light Construction ___Woodsmith
___O1d House Journal _ Woodwork
__ Popular Mechanics _— Woodworker
___Popular Science
___ Popular Woodworking
___Woodworker s Journal
_ Workbench
_— Other
3. Which of the following woodworking/remodeling shows do you watch?
_ Backyard America
___Hame Time
— The American Woodworker
— This Old House
_Woodwright s Shop
___Other
___The New Yankee Workshop
4, What is your annual household income?
___520,000-529,999
___$30,000-$39,999
___8S40,000-S49,999
___560.000-569,999
___S70.000-S79,999
___S80,000-$S89,999
___550,000-559.999 — $90.000 +
5. What is your age group?
- 20-729 ___50-59
___30-39 ___60-69
___40-49 __—_70 +
6. How long have vou been a woodworker?
___0 - 2 Years __8 - 20 Years
___2 - 8 Years — 20+ Years
7. How would you rank your woodworking skills?
_— Simple — Advanced
— Intermediate ___ Master Craftsman
8. What stationary woodworking tools do you own? Check all that apply.
___ Air Compressor — Panel Saw
___Band Saw ___Planer
___Drill Press ___ Power Feeder
___Drum Sander ___Radial Arm Saw
_— Dust Collector ___Shaper
___ Horizontal Boring Machine ___ Spindle Sander
___Jointer __— Table Saw
___Lathe ___Vacuum Veneer Press
___Mortiser ___Wide Belt Sander
— Other
9. How many of your woodworking machines are Grizzly?
13:
— Other
Which benchtop tools do you own? Check all that apply.
_ 1"x 472" Belt Sander _— 6" - $" Grinder
_— 5" - 8" Drill Press _— Mini Lathe
___8" Table Saw — 10" - 12" Thickness Planer
_— 8" - 10" Bandsaw — Scroll Saw
— Disc/Belt Sander
_— Mini Jointer
___Spindle/Belt Sander
___ Other
How many of the machines checked above are Grizzly?
Which portable/hand held power tools do you own? Check all that apply.
—. Belt Sander
Biscuit Joiner
Circular Saw
_ Orbital Sander
— Palm Sander
___ Portable Planer
___ Detail Sander ___ Saber Saw
_— Prill/Driver ___Reciprocating Saw
Miter Saw ___Router
___ Other
What machines/supplies would you like Grizzly Industrial to carry?
_ 12" Table Saw ___ Radial Arm Saw
— 12" Jointer _ Panel Saw
_— Combination Planer/Jointer — _ Brass Hardware
— Paint & Finishing Supplies ___Lumber
___Contractor s Supplies
___ Other
What new accessories would you like Grizzly Industrial to carry?
Builders Hardware
Fasteners
Hand Tools
___Wood Components
What other companies do you purchase your tools and supplies from?
Do you think your purchase represents good value?
Yes No
Would vou recommend Grizzly Industrial to a friend?
Yes No
Would you allow us to use your name as a reference for Grizzly customers
in your area? Note: We never use names more than three times.
__ Yes No
Comments:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement