GE Monogram Refrigerator ZFSB25D SS Installation instructions

Installation
Instructions
If you have questions, call 800.GE.CARES or visit our website at: www.monogram.com
Free-Standing Side-by-Side
Stainless Steel Refrigerator
ZFSB25D SS
ZFSB26D SS
Safety Information
CAUTION:
BEFORE YOU BEGIN
Due to the weight and size of this refrigerator, and to
reduce the risk of personal injury or damage to the
product – TWO PEOPLE ARE REQUIRED FOR
PROPER INSTALLATION.
Read these instructions completely and carefully.
•
IMPORTANT – Save these instructions
for local inspector’s use.
•
IMPORTANT
PRUDENCE :
– Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
À cause du poids et de la taille de ce réfrigérateur et
pour réduire le risque de blessure et de dommages,
IL FAUT DEUX PERSONNES POUR FAIRE
L’INSTALLATION CORRECTEMENT.
WARNING:
WARNING:
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service cords
that become frayed or damaged.
• Unplug the refrigerator before cleaning or making
repairs.
• Repairs should be made by a qualified service
technician.
This appliance must be properly grounded. See
“Grounding the Refrigerator,” page 4.
AVERTISSEMENT :
Cet appareil doit être correctement mis à la terre.
Consulter « Mise à la terre du réfrigérateur », page 4.
AVERTISSEMENT :
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
• Il ne faut utiliser cet appareil que pour l’utilisation
appropriée.
• Réparer ou remplacer immédiatement tout cordon
électrique effiloché ou endommagé.
• Il faut débrancher le réfrigérateur avant le
nettoyage ou toute intervention.
• Les réparations doivent être faites par un technicien
qualifié.
Skill Level – Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliance Warranty. See the
Owner’s Manual for warranty information.
For Monogram local service in your area, call
1.800.444.1845.
For Monogram service in Canada, call
1.888.880.3030
For Monogram Parts and Accessories, call
1.800.626.2002.
www. monogram.com
CONTENTS
Planning Information
Product Dimensions and Clearances ..............................3
The Installation Space ......................................................3
Step 2A, RO Water Line ..................................................8
Step 3, Connect Water Supply ........................................8
Step 4, Connect Power ....................................................8
Step 5, Move Refrigerator Into Position ........................8
Step 6, Level Refrigerator ................................................9
Step 7, Level Doors ..........................................................9
Step 8, Start Icemaker ....................................................10
Step 9, Temperature Controls ........................................10
Step 10, Install Toekick ..................................................10
Installation Instructions
Tools, Hardware, Materials ..............................................4
Grounding the Refrigerator ............................................4
Step 1, Move Refrigerator Indoors (ZFSB25) ................5
Step 1A, Move Refrigerator Indoors (ZFSB26) ..............6
Step 2, Install Water Line ................................................7
2
Planning Information
THE INSTALLATION SPACE
PRODUCT DIMENSIONS
AND CLEARANCES
32"
Depth
The opening width must be 36-1/4".
36-1/2"
28"
Depth
72"
Wall View
72-1/4"
73" min.
Electrical
Area
Water Supply
36"
36"
30-1/2"
Including
Handles
34"
Including
Handles
Water And Electrical Locations
The opening must be prepared with the electrical
and water supply located as shown.
ZFSB25
ZFSB26
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall.
NOTE: GFI (ground fault interrupter) is not
recommended.
• Water line can enter the opening through the
floor or through an adjacent cabinet, as close to
the back wall as possible. The water line should be
1/4" O.D. copper tubing between the cold water
line and water connection location at the rear of the
refrigerator. Installation of an easily accessible shut
off valve in the water line is recommended.
This Monogram free-standing refrigerator requires
the following clearances for proper air circulation,
plumbing and electrical connections.
Air Circulation Clearances:
• 1/8" on each side
• 1" at the top
• 1" at the back (1-1/2" for ZFSB25)
Installation in a corner:
• Allow 4" clearance on each side to an adjacent wall
for a 90° opening and access to drawers.
ZFSB25 and ZFSB26
14-1/4"
ZFSB25 ZFSB26
19"
160° Door Swing
• On the freezer side, allow 14-1/4" min. clearance
for removal of ice bin.
• On the fresh food side, allow 19" min. clearance
to wall for removal of drawers.
3
Installation Instructions
TOOLS REQUIRED
FLOORING
• Tinsnips to cut banding
• Stepladder
• Bucket
• Level
• Appliance hand truck
• Tubing cutter
• #2 Phillips screwdriver
• Drill and appropriate bits
• 3/8", 5/16" and 7/16" hex socket
• 1/8" Allen wrench
• Safety glasses
For proper installation, this refrigerator must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should be
strong enough to support a fully loaded refrigerator.
IMPORTANT NOTE: Protect the finish of the flooring.
Cut a large section of the cardboard carton and place
under the refrigerator where you are working.
MATERIALS REQUIRED
• 1/4" O.D. compression nut and 2 ferrules (sleeves)
GROUNDING THE REFRIGERATOR
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG
FROM THE POWER CORD.
IMPORTANT – (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLY GROUNDED.
The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall receptacle to
minimize the possibility of electric shock hazard
from this appliance.
DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong
wall outlet.
4
Installation Instructions
REMOVE THE DOORS
STEP 1 MODEL ZFSB25
The top cap must be removed to access hinges. It is best
to remove one door at a time.
A. Remove 2 screws on top and 2 screws at the back of
the top cap. Lift off top cap.
B. Open both doors. Remove the 2 toekick screws and
pull forward to remove.
C. Disconnect the water line coupler by pushing against
the collar on the left side. Disconnect wire harness.
D. Remove 2 screws holding top hinge to the case.
Carefully lift off door.
(GO TO STEP 1A FOR
MODEL ZFSB26)
MOVE REFRIGERATOR INDOORS
IMPORTANT:
Door and passageways into
the installation location require a 31" min. opening. If
the opening is less than 31", the top cap and doors must
be removed.
NOTE: Skip this step if door removal is not required.
See instructions on next page, “To Move The
Refrigerator Indoors.”
Follow the same procedure to remove the fresh food
door.
NOTE: To prevent damage, leave inside
packaging, door spacer and outside
protective wrap in place until the unit is
moved to the installation location.
A
Hinge Screws
D
C
B
Toekick Screw
Wire Harness
Water Line Coupler
5
Installation Instructions
STEP 1A MODEL ZFSB26
REMOVE THE DOORS
MOVE REFRIGERATOR INDOORS
The top cap must be removed to access hinges. It is best
to remove one door at a time.
A. Remove 2 screws and springs on top of the
refrigerator, one on each side. Push the top cap
forward and lift up from the rear.
B. Remove 2 screws holding the top filler strip, lift off.
C. Open both doors. Remove the 2 toekick screws and
pull forward to remove.
D. Disconnect the water line coupler by pushing against
the collar on the left side. Disconnect wire harness.
E. Remove 2 screws holding top hinge to the case.
Carefully lift off door.
IMPORTANT:
Door and passageways
into the installation location require a 36" min. opening.
If the opening is less than 36", the top cap and doors
must be removed.
NOTE: Skip this step if door removal is not required.
See instructions on next page, “To Move The
Refrigerator Indoors.”
Follow the same procedure to remove the fresh food
door.
NOTE: To prevent damage, leave inside
packaging, door spacer and outside
protective wrap in place until the unit is
moved to the installation location.
A
B
Hinge Screws
E
D
C
Toekick Screw
Wire Harness
Water Line Coupler
6
Installation Instructions
STEP 1 ALL MODELS (continued)
REINSTALL DOORS
Refer to the illustration on page 5 or 6.
• Carefully, route the water line tubing and electrical
through the freezer side bottom hinge. Lower the door
onto bottom hinge.
• Secure top hinge.
• Insert the tubing all the way into the coupler.
• Reconnect the wiring harness.
• Replace top filler strip (on model ZFSB26).
• Replace top cap with original screws and springs
(where present).
HINT: Use tape or Perma Gum to prevent the spring
from sliding off the screw (on model ZFSB26).
Follow the same procedure to reinstall the fresh food door.
To move the refrigerator indoors:
• Place a piece of the carton or soft cloth against the
side panel of the refrigerator to pad and protect the
stainless steel finish.
• Place the refrigerator on the handtruck with a side
against the truck only.
• Move the refrigerator indoors.
STEP 2 INSTALL WATER LINE
• A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 40 and 120 p.s.i.
• Route 1/4" OD copper tubing between house cold
water line and the water connection location.
• Measure the distance from the water valve on the
back of the refrigerator to the water supply line.
Add 8 foot length to allow the refrigerator to be
moved away from the wall after installation. Bend
the tubing into 3 coils of about 10".
Compression Nut
Saddle Type
Shutoff Valve
Packing Nut
Outlet Valve
NOTE: The only GE approved plastic tubing is
supplied in GE SmartConnect™ Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Certain
types of plastic will crack or rupture with age and cause
water damage to your home.
Ferrule
(Sleeve)
• Drill a 1/4" hole in the water pipe.
• Fasten the shut-off valve to the pipe with pipe clamp.
• Tighten the clamp screws until the sealing washer
begins to swell. Do not over tighten.
• Place a compression nut and ferrule (sleeve) onto the
end of the tubing and connect it to the shut-off valve.
Make sure the tubing is fully inserted into the valve and
ferrule is tightened.
• Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into a
bucket. Shut off water supply at the shut-off valve.
GE SmartConnect™ Refrigerator Tubing Kits are
available in the following lengths:
2' (.6 m)
– WX08X10002
6' (1.8 m)
– WX08X10006
15' (4.6 m)
– WX08X10015
25' (7.6 m)
– WX08X10025
NOTE: Saddle type shut-off valves are included in many
water supply kits. Before purchasing, make sure a saddle
type valve complies with your local plumbing codes.
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the
line of water.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
NOTE: It is best to install the valve into a vertical water
pipe. If you install the valve into a horizontal water
pipe, make the connection at the top or side to avoid
drawing off any sediment from the water pipe.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves are
illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
7
Installation Instructions
Step 2A WATER LINE
INSTALLATION WITH
A REVERSE OSMOSIS
SYSTEM
STEP 3 CONNECT WATER SUPPLY
Skip this step when not using RO System
Tubing Clamp
Check to be sure that refrigerator power cord is not
plugged into the wall outlet.
1/4"
Compression Nut
IMPORTANT:
When connecting a GE Reverse Osmosis Water System
to your refrigerator, the GE RVKit must be used.
For other reverse osmosis water systems, follow the
manufacturer’s recommendations.
Ferrule
(sleeve)
Refrigerator Connection
If the water supply to the refrigerator is from a Reverse
Osmosis Water System, use the refrigerator’s filter
bypass plug. Using the refrigerator’s water filtration
cartridge with the RO filter can result in hollow ice
cubes and slower water flow from the water dispenser.
Turn left to remove
1/4" Tubing
SmartConnect™ Tubing
If you are using copper tubing:
• Place compression nut and ferrule (sleeve)
onto the end of the tubing coming from the
house water supply.
• Insert the end of the copper tubing into the
refrigerator connection at the back of the
refrigerator, as far as possible. Hold the tubing
in place and tighten the fitting.
If you are using GE SmartConnect™ tubing:
• Insert the molded end of the tubing into the
refrigerator connection, at the back of the
refrigerator, and tighten the compression nut
until it is hand tight.
• Then tighten one additional turn with a wrench.
Overtightening may cause leaks.
• Fasten the tubing into the clamp provided to hold it
in position. You may need to pry open the clamp.
• Turn on the water at the shut-off valve to check
for leaks.
Turn right to install bypass plug
STEP 4 CONNECT POWER
• Connect refrigerator power cord plug to a properly
grounded receptacle.
• Check to make sure power to refrigerator is on by
opening refrigerator door to see if interior lights
are on.
STEP 5 MOVE REFRIGERATOR
INTO POSITION
• Remove outside protective wrapping.
• Move the refrigerator into final installation position.
• Remove door spacer and all inside packaging.
8
Installation Instructions
STEP 6 LEVEL THE REFRIGERATOR
STEP 7 LEVEL THE DOORS
The refrigerator can be leveled by adjusting the rollers
located near the bottom hinges.
If the doors are not evenly aligned at the top, the
refrigerator door can be adjusted.
• Use a 7/16" hex socket or wrench to turn the door
adjusting screw. Turn the screw to the right to raise
the door, turn left to lower the door.
Raise
Doors Should
Align at Top
Rollers
Rollers have three purposes:
• The rollers adjust so that the door closes easily when
opened about halfway. (Raise the front about 5/8"
[16 mm] from the floor.)
• Rollers adjust to allow the refrigerator to be firmly
positioned on the floor and to prevent rocking
when the doors are opened and closed.
• The rollers allow you to move the refrigerator from
the wall for cleaning.
To Adjust the Rollers:
Raise
NOTE: A nylon plug is imbedded in the threads of
the pin. The plug is designed to prevent the pin from
turning. A wrench must be used to turn the pin.
• Turn the wrench one or two times. Open and close
the refrigerator door to check alignment with the
freezer door at the top. Adjust again if necessary.
Roller Adjusting Screw
• Use a 3/8" hex socket or wrench to turn the
adjustment screws. Turn the screws clockwise to
raise the refrigerator, turn counterclockwise to
lower it.
Roller Adjusting Screws
ZFSB25 rear rollers can also be adjusted.
• Use a 5/16" hex socket to turn the screws for the
rear rollers. Turn the screws clockwise to raise the
refrigerator, counterclockwise to lower it.
9
Installation Instructions
STEP 9 TEMPERATURE
CONTROLS
STEP 8 START ICEMAKER
• The temperature controls are preset at 37° for the
refrigerator and 0°F for the freezer.
• Allow 24 hours to stabilize before making
adjustments.
Power Switch
STEP 10 INSTALL TOEKICK
Feeler Arm
• Press toekick into position and reinstall one screw
on each side.
• Flip the switch to I (ON) position. The icemaker
will not begin to operate until it reaches its
operating temperature of 15°F (–9°C)or below.
It will then begin operation automatically. It will
take 2–3 days to fill the ice bin.
• Be sure nothing interferes with the sweep of the
feeler arm. Do not place objects in the path of the
feeler arm.
• Discard the first full bucket of ice cubes.
• To turn the icemaker off, set the switch to O (OFF).
Toekick Screw
IMPORTANT: The vented toekick must remain
unobstructed for proper air circulation.
10
Notes
11
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram® local service in your area, call
1.800.444.1845.
NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
Pub. No. 49-60476
Dwg. No. 197D4577P002
07-06 JR
Printed in Mexico
GE Consumer & Industrial
GE Appliances
General Electric Company
Louisville, KY 40225
ge.com
©2006 GE Company