Advertisement
Advertisement
29391 Call Waiting Caller ID Speakerphone User’s Guide We bring good things to life. FCC REGISTRATION INFORMATION Your GE telephone equipment is registered with the Federal Communications Commission and is in compliance with parts 15 and 68, FCC Rules and Regulations. 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating, among other information, the FCC Registration number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone company. The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you should contact your local telephone company. Notes • This equipment may not be used on coin service provided by the telephone company. • Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone equipment if you are on a party line. Check with your local telephone company. • Notice must be given to the telephone company upon permanent disconnection of your telephone from your line. 2 Rights of the Telephone Company Should your equipment cause trouble on your line which may harm the telephone network, the telephone company shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone company must: (1) promptly notify you of such temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations. The telephone company may make changes in its communications facilities, equipment, operations of procedures where such action is required in the operation of its business and not inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or performance of your telephone equipment, the telephone company must give you adequate notice, in writing, to allow you to maintain uninterrupted service. INTERFERENCE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the interference). • Reorient or relocate and increase the separation between the telecommunications equipment and receiving antenna. • Connect the telecommunications equipment into an outlet on a circuit different from that to which the receiving antenna is connected. If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering copies. HEARING AID COMPATIBILITY This telephone system meets FCC standards for Hearing Aid Compatibility. 2 FCC NUMBER IS LOCATED ON THE CABINET BOTTOM REN NUMBER IS LOCATED ON THE CABINET BOTTOM TABLE OF CONTENTS FCC REGISTRATION INFORMATION .... 2 INTERFERENCE INFORMATION ............ 2 HEARING AID COMPATIBILITY ........... 2 INTRODUCTION ..................................... 4 BEFORE YOU BEGIN .............................. 5 PARTS CHECKLIST ............................. 5 MODULAR JACK REQUIREMENTS ......... 5 INSTALLATION & SETUP ......................... 6 IMPORTANT INSTALLATION INFORMATION 6 INSTALLING THE BATTERIES ................. 6 DESKTOP INSTALLATION ...................... 8 WALL MOUNT INSTALLATION .............. 9 SETTING UP THE CALLER ID MENU ... 10 SETTING YOUR LOCAL AREA CODE 11 SETTING THE CID DISPLAY LANGUAGE ............................. 12 SETTING THE DISPLAY CONTRAST .. 13 SETTING THE DIAL MODE ............. 14 EXITING SETUP .......................... 14 SUMMARY SCREEN ......................... 15 CALLER ID WITH CALL WAITING ........ 15 CALLER ID FEATURES .......................... 15 RECEIVING AND STORING CALLS ........ 16 REVIEWING CALL RECORDS ............... 16 DELETING CALL RECORDS ................ 17 DIALING BACK ................................ 17 IF YOU PROGRAMMED YOUR LOCAL AREA CODE IN THE SETUP MENU .. 18 IF YOU DID NOT PROGRAM YOUR LOCAL AREA CODE IN THE SETUP MENU .. 19 MESSAGE INDICATORS ......................... 20 USING THE SPEAKERPHONE .................. 21 SPEAKERPHONE LOCATION ................ 21 SPEAKERPHONE USE ....................... 21 WARNING: TELEPHONE BASICS ............................. RECEIVING A PHONE CALL ................ PLACING A PHONE CALL .................. SWITCHING BETWEEN SPEAKER AND HANDSET ............................... TEMPORARY TONE DIALING ........... VOLUME CONTROL .......................... REDIAL .......................................... ONE -TOUCH REDIAL ....................... HOLD ............................................ FLASH ........................................... MEMORY ........................................... STORING QUICK DIAL NUMBERS ....... STORING FREQUENTLY CALLED NUMBERS ...................................... REVIEWING NUMBERS STORED IN MEMORY ....................................... QUICK DIAL NUMBERS ................. FREQUENTLY CALLED NUMBERS ..... CHANGING A STORED NUMBER ......... ERASING A STORED NUMBER ............ STORING A PAUSE IN MEMORY ......... DIALING A QUICK DIAL NUMBER ....... DIALING FREQUENTLY CALLED NUMBERS ...................................... TROUBLESHOOTING TIPS ...................... GENERAL PRODUCT CARE .................... SERVICE ............................................ INDEX ............................................... LIMITED WARRANTY ............................ TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 22 22 22 22 23 23 23 24 24 25 26 26 27 27 27 28 28 28 28 29 29 30 32 32 33 35 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THE LIGHTNING FLASH AND ARROWHEAD WITHIN THE TRIANGLE IS A WA R N I N G S I G N ALERTING YOU OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERS E R V I C E A B L E PA R T S I N SIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF I M P O R T A N T INSTRUCTIONS A C C O M PA N Y I N G T H E P R O D U C T. SEE MARKING ON BOTTOM / BACK OF PRODUCT 3 INTRODUCTION Your Caller ID phone stores and displays specific information, provided by your local telephone company, to subscribers of Caller ID or similar caller identification services. You must subscribe to one of these services in order to use this unit. Your Caller ID phone enables you to: • Identify callers before you answer the phone. • View the time and date of each incoming call. • Record up to 60 Caller ID messages sequentially. • Know who called while you were away. IMPORTANT: In order to use this unit, you must subscribe to either the standard Name/Number Caller ID Service or Caller ID with Call Waiting Service. To know who is calling while you are on the phone, you must subscribe to Caller ID with Call Waiting Service. 4 BEFORE YOU BEGIN PARTS CHECKLIST Make sure your package includes the following items: OPTIONS A B DELETE REVIEW DIAL Short telephone line cord STORE 1 2 ABC 3 DEF 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER REDIAL VOLUME * HOLD # FLASH SPEAKER Telephone line cord Coiled cord Handset Base MODULAR JACK REQUIREMENTS You need an RJ11 type modular jack, which is the most common type of phone jack and might look like the one pictured here. If you don’t have a modular jack, call your local phone company to find out how to get one installed. 5 INSTALLATION & SETUP IMPORTANT INSTALLATION INFORMATION • Never install telephone wiring during a lightning storm. • Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at the network interface. • Use caution when installing or modifying telephone lines. INSTALLING THE BATTERIES Your Caller ID phone uses 4 AA-size alkaline batteries for receiving and storing Caller ID records and for the numbers you use for memory dialing. IMPORTANT: You will have approximately 60 seconds to replace the batteries before the memories stored are lost. Please read the instructions before replacing the batteries and have the batteries ready to be inserted beforehand. 1. If the line cord is already connected, disconnect it from the base unit. 2. Use a screwdriver to pry up the battery compartment door on the bottom of the phone. 3. Insert 4 AA-size alkaline batteries as shown on the diagram in the battery compartment. 4. Snap the battery compartment door back into place. 5. If the line cord was previously connected, re-attach it to the unit and check your memory locations. 6 NOTE: If the low battery icon appears in the display, you need to replace the batteries. It is important that you replace the batteries as soon as possible in order to maintain Caller ID operation. During the replacing of batteries, a backup circuit in the unit will retain your stored information for up to 60 seconds. Write down any stored information you do not want erased. IMPORTANT: If you’re not going to use the telephone for more than 30 days, remove the batteries because they can leak and damage the unit. Battery compartment 7 DESKTOP INSTALLATION 1. Plug the coiled cord into the handset. Plug the other end into the jack on the side of the base. Place the handset in the cradle on the base. 2. Plug the line cord into jack on the back of the base. Plug the other end into a wall jack. 3. Set the RINGER switch on the base to the desired loudness. • HI = Default, loudest sound. • LO = Sound will be lower. • OFF = Telephone will not ring. 1 2 3 8 WALL MOUNT INSTALLATION 1. Carefully turn the phone over. Detach the wall mount bracket from the two sets of top grooves by pressing the tabs in. Pull the bracket from the phone and turn it around so that it looks like the diagram below. Gently press the bracket into the two sets of bottom grooves until it snaps into place. 2. Plug the short line cord into the jack on the back of the base. 3. Feed the line cord through the grooves provided so that the base area is flat and ready to mount on the wall. 4. Connect the other end of the line cord into the wall phone jack. 5. Place the handset in the cradle of the base as soon as possible to hang up the phone. 6. Plug the coiled cord into the handset. Plug the other end into the jack on the side of the base. 7. Slip the mounting holes of the base (on bottom of unit) over the wall plate posts and slide the base down until the phone is firmly in place. 8. Set the RINGER switch on the base to the desired loudness. • HI = Default, loudest sound. • LO = Sound will be lower. • OFF = Telephone will not ring. 8 2 7 6 3 4 1 9 SETTING UP THE CALLER ID MENU You should not plug the telephone into the wall line jack while setting up the Caller ID menu. An incoming call may invalidate the change if it was not yet saved. The phone must display xx CALLS before you can enter the setup menu. OPTIONS REVIEW button buttons 1. Press the OPTIONS button. OPTIONS MENU ^ v appears. 2. At this point you can press either REVIEW up or down button to scroll among the 6 menu screens, which are: OPTIONS A B DELETE REVIEW 12:30 10/19 • # 1 OPTIONS MENU ^ v • # 2 LOCAL AREA CODE (default - - -) • # 3 LANGUAGE (default English) • # 4 (LCD) CONTRAST (default 3) • # 5 T/P DIAL MODE (default tone) • # 6 EXIT OPTIONS 3. You have 10 seconds following any key press before the phone will automatically return to the Summary Screen. 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER AM PM Summary Screen 10 3 SETTING YOUR LOCAL AREA CODE The telephone uses the programmed area code to determine the number format to display when a valid Caller ID signal is received and is also used for the Dialback feature. 1. Press the OPTIONS button. OPTIONS MENU ^ v appears. 2. Press the REVIEW up or down buttons until LOCAL AREA CODE appears. 3. To enter and change the area code, press OPTIONS again. The display shows the present area code stored. The left-most digit or a minus sign (-) flashes, indicating it is ready to accept the area code entry. 4. Press 1-9 on the key pad for the first digit. To clear the digit, press either * or #. OPTIONS REVIEW button buttons OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER 5. When the desired digit is flashing, press either REVIEW button to advance to the next digit. 11 6. Repeat steps 4 and 5 until all the digits for your area code are correct. If you make a mistake, you can simply retrace the previous steps until your area code is set. 7. Press OPTIONS once again to store the area code and return to the “LOCAL AREA CODE” display. OPTIONS button REVIEW buttons SETTING THE CID DISPLAY LANGUAGE This adjustment changes the Caller ID prompts to be displayed in English or Spanish. OPTIONS B REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL 1. Press the OPTIONS button. OPTIONS MENU ^ v appears. A DELETE STORE 1 2 ABC 3 DEF REDIAL 2. Press the REVIEW up button until LANGUAGE appears. 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 3. To enter and change the language, press the OPTIONS button. The display shows the current language. The default is English. * 0 PER VOLUME 4. Press either REVIEW button to change the setting. 5. Press OPTIONS once again to store the setting and return to the “LANGUAGE” display. 12 HOLD # FLASH SPEAKER SETTING THE DISPLAY CONTRAST This adjustment allows optimization of the contrast and viewing angle of the display. 1. Press the OPTIONS button. OPTIONS MENU ^ v appears. 2. Press the REVIEW up button until (LCD) CONTRAST appears. 3. To enter and change the contrast, press the OPTIONS button. The display shows the current contrast setting. There are 5 levels of contrast, with the default set to 3. 4. Press either REVIEW button to change the setting. 5. Press OPTIONS once again to store the setting and return to the “(LCD) CONTRAST” display. OPTIONS REVIEW button buttons OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER 13 SETTING THE DIAL MODE This adjustment allows you to select tone (touch-tone) or pulse (rotary) mode dialing. 1. Press the OPTIONS button. OPTIONS MENU ^ v appears. 2. Press the REVIEW up button until T/P DIAL MODE appears. 3. To enter and change the dial mode, press the OPTIONS button. The display shows the current setting. The default is set to tone. OPTIONS button OPTIONS 4. Press either REVIEW button to change the setting. 5. Press OPTIONS once again to store the setting and return to the “T/P DIAL MODE” display. REVIEW buttons A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME EXITING SETUP To exit the Setup menu after your changes have been made, you can immediately exit by selecting the "EXIT OPTIONS" menu and pressing the OPTIONS button. 14 * HOLD # FLASH SPEAKER CALLER ID FEATURES SUMMARY SCREEN The Summary Screen shows the current time, date, and number of new calls to be reviewed. It is displayed until the REVIEW or OPTIONS buttons are pressed or a Caller ID record is received. Within 10 seconds of receiving a new call, the Summary Screen is displayed and the New Call LED flashes. NOTE: The number of new calls is displayed until all new calls have been reviewed. AM PM NEW CALL indicator OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE CALLER ID WITH CALL WAITING Provided your telephone company is able to integrate Caller ID and Call Waiting services, you are able to see who is calling when you hear the call waiting beep. The caller identification information appears in the display after you hear the tone. • Press the FLASH button to put the current person on hold so that you can answer the incoming call. 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER FLASH button 15 RECEIVING AND STORING CALLS This unit receives and displays information transmitted by your local phone company. This information can include the phone number, date, and time; or the name, phone number, date, and time. The unit can store up to 60 calls for later review. When the memory is full, a new call automatically replaces the oldest call in memory. NEW appears in the display for calls received that have not been reviewed. REVIEWING CALL RECORDS REVIEW buttons OPTIONS • Press the REVIEW up button to scroll through the call records from the oldest to the newest. • When all of the messages have been viewed, START/END appears in the display. 16 B REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL • Press the REVIEW down button to scroll through the call records from the most recent to the oldest. A DELETE STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER DELETING CALL RECORDS • To delete the record shown in the display, press the DELETE button once. • To delete all records while reviewing, press and hold the DELETE button for about 3 seconds. DELETE ALL? appears in the display. Press DELETE again to complete. DELETE button Dial button DIALING BACK When reviewing Caller ID records, you can dialback the numbers shown on the display by pressing the DIAL button. OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE NOTE: You must press DIAL before you pick up the handset. 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME NOTE: If only PICKUP PHONE shows on the display, no other changes to the number can be made. The information sent from the telephone company is known to be a valid number for dialing back (utilized only in very limited areas). Once you pickup the phone or press SPEAKER the number will be automatically dialed. * HOLD # FLASH SPEAKER SPEAKER button 17 IF YOU PROGRAMMED YOUR LOCAL AREA CODE IN THE SETUP MENU 1. Use the REVIEW up and down buttons to display the number you want to dial. • If you see a number with 7 digits (i.e. 555-1234), then the call was received from within your area code. However, this does not guarantee the call is a local call. • If you see a number with 11 digits (i.e. 1234-555-1234), then the call received was not from your area code. 2. To adjust the phone number, press the OPTIONS button. For instance, a 7-digit local number sometimes cannot be dialed because it requires a 10-digit or 11-digit format. Press the OPTIONS button repeatedly to scroll through the 7, 10, and 11-digit numbers. OPTIONS button OPTIONS REVIEW buttons A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER 7-digits: 7-digit telephone number (i.e. 555-5555) 10-digits: 3-digit area code + 7-digit telephone number (i.e. 425-555-5555) 11-digits: long distance code 1 + 3digit area code + 7-digit telephone number (i.e. 1-425-555-5555) 18 3. Press the DIAL button and the display shows PICKUP PHONE. A 10 second timer will also start at this point on the upper right side of the display, letting you know the time until the unit will return to the Caller ID record. DIAL button REVIEW buttons OPTIONS • If you adjust the number to be dialed, the timer will reset after each adjustment. A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 4. Pick up the handset or press SPEAKER before the timer reaches 0. NOW DIALING shows in the display and the number is dialed. 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER IF YOU DID NOT PROGRAM YOUR LOCAL AREA CODE IN THE SETUP MENU 1. Use the REVIEW up and down buttons to display the number you want to dial. You will only see 10-digit numbers (i.e. 234555-1234). 2. See steps 2 through 4 in the above section to complete the dialback sequence. 19 MESSAGE INDICATORS The following special messages indicate the status of a message or the unit: NO CALLS The caller memory is empty. UNKNOWN CALL The incoming call does not have Caller ID service or their service area is not linked to yours. If UNKNOWN CALL appears along with a calling number, the name information for that number was not available. BLOCKED CALL The caller of the incoming call is registered as “Private Number” and their Caller ID information is withheld. ERROR Caller information has been interrupted or corrupted during transmission. NO DATA No Caller ID signal has been detected, or Caller ID service has not been activated. START/END You are at the beginning or the end of the Caller ID memory log. Battery power level is low. 20 USING THE SPEAKERPHONE SPEAKERPHONE LOCATION For best speakerphone performance, avoid the following: • Areas with high background noise. (The microphone might pick up these sounds and prevent the speakerphone from going into the receiving mode when you finish talking.) • Surfaces affected by vibration. OPTIONS • Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can generate an echo effect. Note the following guidelines when using the speakerphone: B REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 SPEAKERPHONE USE A DELETE 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER • The speakerphone works similar to a two-way radio in that you can only listen or talk at one time. • Stay reasonably close to the phone so that you can be clearly heard by the person to whom you are talking. VOLUME buttons Speaker Phone Indicator • You can adjust the speaker volume by pressing the VOLUME up or down buttons. • The speakerphone indicator light comes on when the speakerphone is in use. 21 TELEPHONE BASICS RECEIVING A PHONE CALL 1. Be sure the RINGER switch is set to the HI or LOW position. 2. When the phone rings and the caller’s information shows on the display, lift the handset or press the SPEAKER button and begin your conversation. OPTIONS 4. You can adjust the volume of the caller’s voice by pressing the VOLUME up or down buttons. Set the RINGER switch to the OFF position when you do not want to be interrupted by the phone ringing. B REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL 3. A DELETE STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER PLACING A PHONE CALL 1. Lift the handset or press the SPEAKER button and wait for a dial tone. 2. Dial the telephone number you wish to call. 3. You can adjust the volume of the caller’s voice by pressing the VOLUME up or down buttons. VOLUME buttons SPEAKER button SWITCHING BETWEEN SPEAKER AND HANDSET You can switch between speakerphone and handset while the phone is dialing a number, or anytime during a conversation. • Speaker to Handset — Pick up the handset. • Handset to Speaker — Press SPEAKER, then hang up handset. 22 TEMPORARY TONE DIALING If you have pulse service, you can temporarily change from pulse to tone service. After dialing the telephone number, press and release the * button on the telephone. This allows access to phone services that require a tone, such as banking and long-distance services. After you hang up the handset, the telephone automatically returns to pulse service. REDIAL button OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE VOLUME CONTROL This feature allows you to increase the listening volume in the receiver of the handset when speaking with your party. When needed, press the VOLUME up and down buttons. REDIAL 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER VOLUME buttons If the number you dialed is busy, or you want to call the last number dialed again, press REDIAL. The number shows on the display and dials automatically. 23 ONE -TOUCH REDIAL If the last call you dialed was busy, you can redial it immediately by just pressing the REDIAL button without hanging up the handset. NOTE: The Redial feature stores in memory all the numbers you press. If you press any numbers after dialing the phone number you last called (for example, when accessing a voice mail system), those numbers are also dialed when using Redial. This may cause the phone to try to dial all the numbers at once. REDIAL button OPTIONS A REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 24 DEF 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD 2. To resume your conversation, lift the handset or that of any extension phone on the same line or press the SPEAKER button. 3 REDIAL HOLD 1. To place a call on hold, press the HOLD button and hang up the handset. (If you were in speakerphone mode, the unit automatically puts the call on hold.) The HOLD indicator blinks until you resume your conversation. B DELETE # FLASH SPEAKER HOLD button and indicator SPEAKER button FLASH This feature is used to activate customer calling services available through your local phone company, such as Call Waiting. These services generally require an extra monthly fee. If you subscribe to any of these services, please refer to the phone company’s instructions on how to use FLASH. See the "Caller ID Features" section for more information on Caller ID with Call Waiting. 1. While having a conversation, another party calls and you hear a tone. 2. Press the FLASH button once and release. The first conversation is placed on hold and the second call can be answered. 3. Press FLASH again and release. The first caller can be spoken to again and the second call is placed on hold. OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER FLASH button 25 MEMORY Before you store any telephone number into memory, make sure the dial mode is correct for the type of telephone you’re using. The default dial mode is tone (touch-tone), so if you have pulse (rotary) service, you must first change the dial mode. See “To Set the Dial Mode.” The following buttons can be stored into any memory location: 0-9, *, # and PAUSE (REDIAL). See "Storing a Pause in Memory" and "Temporary Tone Dialing". STORE button Quick Dial buttons OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORING QUICK DIAL NUMBERS STORE 1. Pick up the handset or press the SPEAKER button. 2. Press STORE. 3. Enter the telephone number (up to 20 digits). If you make a mistake, hang up and repeat the procedure for storing from the beginning. NOTE: It will not actually call the number in this mode. 4. Press STORE. 5. Press selected Quick Dial location A or B. 6. Hang up the handset or press SPEAKER again. 7. Write the name or number of party stored in the memory location on the directory card. 26 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER SPEAKER button STORING FREQUENTLY CALLED NUMBERS 1. Pick up the handset or press the SPEAKER button. 2. Press STORE. 3. Enter the telephone number (it will not actually call the number in this mode). If you make a mistake, hang up and repeat the procedure for storing from the beginning. 4. Press STORE. 5. Press 0-9 for the memory location. 6. Hang up the handset or press SPEAKER again. 7. Write the name or number of party stored in the memory location on the directory card. REVIEWING NUMBERS STORED IN MEMORY STORE button Quick Dial buttons OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER SPEAKER button QUICK DIAL NUMBERS 1. Make sure the handset is hung up. 2. Press Quick Dial A or B. The number shows on the display. 27 FREQUENTLY CALLED NUMBERS 1. Make sure the handset is hung up. 2. Press DIAL. 3. Press 0-9 for the memory location. The number shows on the display. CHANGING A STORED NUMBER Repeat the storage sequence. The new number replaces the old number at the memory location. STORE button DIAL button OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL ERASING A STORED NUMBER STORE 1. Pick up the handset or press SPEAKER. 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 2. Press STORE. 7 PQ RS 8 TUV 9 WX YZ 3. Press STORE again. * 0 PER VOLUME HOLD 4. Press the location (A, B, 0-9) to be erased. STORING A PAUSE IN MEMORY The REDIAL button becomes a pause function when the STORE button has been pressed first. It is valid only when storing a number into memory locations. Use the PAUSE (REDIAL) button to insert a pause when a delay is needed in an automatic dialing sequence. For example, when you must dial a 9 to get an outside line or when you enter codes to access you long distance company. 28 # FLASH SPEAKER SPEAKER button REDIAL button You may need to adjust the length of the pause duration. It can be adjusted from 1 to 9 seconds. The default setting is 4 seconds. 1. Pick up the handset or press SPEAKER. 2. Press the STORE button. 3. Press 1-9 (1=1 second, 2=2 seconds, etc.) STORE button Quick Dial buttons DIAL button 4. Press STORE again. 5. Press the PAUSE (REDIAL) button to save. OPTIONS A B DELETE DIALING A QUICK DIAL NUMBER 1. Pickup the handset or press SPEAKER. 2. Press the Quick Dial location A or B. The number shows on the display and dials automatically. REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER DIALING FREQUENTLY CALLED NUMBERS 1. Pick up the handset or press SPEAKER. SPEAKER button REDIAL button 2. Press DIAL. 3. Press 0-9 for the memory location. The number dials automatically. 29 TROUBLESHOOTING TIPS NO DIAL TONE • Check all cabling to make sure that all connections are secure and not damaged. • Check hook switch: Does it fully extend when handset is lifted from cradle? NO DISPLAY • Replace batteries. • Check for proper battery installation. NO INFORMATION IS SHOWN AFTER THE PHONE RINGS • Did you order Caller ID service from your local telephone company? This unit requires that you subscribe to Caller ID service in order to work. • Be sure to wait until the second ring before answering. ERROR MESSAGE IS DISPLAYED • ERROR appears in the display if the unit detects anything other than valid Caller ID information during the silent period after the first ring. This message indicates either the presence of noise on the line, or that an invalid message has been sent from the telephone company. PHONE DOES NOT DIAL OUT • Check the dial mode in the setup menu. Is it set to tone, which may not be compatible with your local dialing service? 30 PHONE DOES NOT RING • Is the ringer switch in the OFF position? • Are you using too many phones on one line? (The total REN of all phones on the same line should not be greater than the maximum REN for your calling area. See FCC Registration Information) • Perform the checks under the first problem (Number 1). Is the hook switch depressed fully when handset is in cradle? INCOMING AND OUTGOINGVOICE VOLUME LOW • Are other phones off hook at same time? If so, this is normal condition as volume drops when additional phones are used at once. TONE FEEDBACK FLUTTER WHEN DIALING IN PULSE MODE • This is normal as power is fluctuating with phone outpulsing. 31 GENERAL PRODUCT CARE To keep your phone working and looking good, follow these guidelines: • Avoid putting near heating appliances and devices that generate electrical noise ( for example, motors and flourescent lamps). • DO NOT expose to direct sunlight or moisture. • Avoid dropping and other rough treatment of the unit. • Never use a strong cleaning agent or abrasive powder because this will damage the finish. • Retain the original package in case you need to ship it at a later date. SERVICE FCC requires this product be serviced only by the manufacturer or its authorized service agents. In accordance with FCC requirements, changes or modifications not expressly approved by Thomson Consumer Electronics could void the user’s authority to operate this product. For instructions on how to obtain service, refer to the warranty included in this guide or call customer service at 1-800-448-0329. Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or received as a gift. This information will be valuable if service should be required during the warranty period. Purchase date ________________________________________________ Name of store ________________________________________________ 32 INDEX B I Before You Begin 5 If you did not program your local area code in the 19 If you programmed your local area code in the setu 18 Important Installation Information 6 Installation & Setup 6 Installing the Batteries 6 Interference Information 2 Introduction 4 C Caller ID Features 15 Caller ID with Call Waiting 15 Changing a Stored Number 28 D Deleting Call Records 17 Desktop Installation 8 Dialing a Quick Dial Number 29 Dialing Back 17 Dialing Frequently Called Numbers 29 E L Limited Warranty 35 M Erasing a Stored Number 28 Exiting Setup 14 Memory 26 Message Indicators 20 Modular Jack Requirements 5 F O FCC Registration Information 2 Flash 25 Frequently Called Numbers 28 One -Touch Redial 24 G P Parts Checklist 5 Placing a Phone Call 22 General Product Care 32 H Hearing Aid Compatibility 2 Hold 24 33 Q T Quick Dial Numbers 27 Telephone Basics 22 Temporary Tone Dialing 23 Troubleshooting Tips 30 R Receiving a Phone Call 22 Receiving and Storing Calls 16 Redial 23 Reviewing Call Records 16 Reviewing Numbers Stored in Memory 27 U Using the Speakerphone 21 V Volume Control 23 S W Service 32 Setting the CID Display Language 12 Setting the Dial Mode 14 Setting the Display Contrast 13 Setting Up the Caller ID Menu 10 Setting Your Local Area Code 11 Speakerphone Location 21 Speakerphone Use 21 Storing a Pause in Memory 28 Storing Frequently CalledNumbers 27 Storing Quick Dial Numbers 26 Summary Screen 15 Switching between Speaker and Handset 22 Wall Mount Installation 9 34 LIMITED WARRANTY What your warranty covers: • Any defect in materials or workmanship. For how long after your purchase: • One year. (The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever comes first.) What we will do: • Provide you with a new or, at our option, a refurbished unit. • The exchange unit is under warranty for the remainder of the original product’s warranty period. How to make a warranty claim: • Properly pack your unit. Include any cables, etc., which were originally provided with the product. We recommend using the original carton and packing materials. • Include evidence of purchase date such as the bill of sale. Also print your name and address and a description of the defect. Send via standard UPS or its equivalent to: Thomson Consumer Electronics, Inc. 11721 B Alameda Ave. Socorro, Texas 79927 • Pay any charges billed to you by the Exchange Center for service not covered by the warranty. • Insure your shipment for loss or damage. Thomson accepts no liability in case of damage or loss en route to Thomson. • A new or refurbished unit will be shipped to you freight prepaid. What your warranty does not cover: • Customer instruction. (Your Owner’s Manual provides information regarding operating instructions and user controls. For additional information, ask your dealer.) • Installation and set-up service adjustments. • Batteries. • Damage from misuse or neglect. • Products which have been modified or incorporated into other products. • Products purchased or serviced outside the USA. • Acts of God, such as but not limited to lightning damage. Product Registration: • Please complete and mail the Product Registration Card packed with your unit. It will make it easier to contact you should it ever be necessary. The return of the card is not required for warranty coverage. How state law relates to this warranty: • This warranty gives you specific legal rights, and you may have other rights which vary from state to state. If you purchased your product outside the USA: • This warranty does not apply. Contact your dealer for warranty information. 35 Model 29391A 15403020 (Rev. 1 E/S) 99-34 Printed in China P.O. Box 1976, Indianapolis, IN 46206 © 1999 Thomson Consumer Electronics, Inc. Trademark(s) ® Registered Marca(s) Registrada(s) 29391 Llamada en Espera Identificador de Llamadas con Altavoz Guía del Usuario Creamos cosas buenas para la vida. INFORMACIÓN DE LA REGISTRACIÓN DE LA FCC Su equipo telefónico de la GE ha sido registrado con la Comisión Federal de Comunicaciones (FCC) y está en acuerdo con las Partes 15 y 68 de las Regulaciones y Reglas de la FCC. 1 Notificación a la Compañía Telefónica Local Al fondo de este equipo Ud. hallará un rótulo indicando, entre otra información, el número de la Registración con la FCC y el Número del Equivalente Timbre (REN) para este equipo. Ud. deberá, a petición, proveer esta información a su compañía telefónica. El REN es útil para determinar el número total de artefactos que Ud. puede conectar a su línea telefónica, todavía asegurando que todos estos artefactos sonarán cuando se llame su número telefónico. En la mayoría de las áreas (pero no en todas), el total de los números REN de todos los artefactos conectados a una línea no debe exceder 5. Para estar seguro del número total de artefactos que Ud. pueda conectar a su línea (determinado por el REN), Ud. deberá ponerse en contacto con su compañía telefónica local. NOTAS: • No se puede usar este equipo con un teléfono de previo pago proveído por la compañía telefónica. • Las líneas compartidas son sujetas a las tarifas del estado, y por eso, es posible que Ud. no pueda usar su propio equipo telefónico si Ud. estuviera compartiendo la misma línea telefónica con otros abonados. • Se debe notificar la compañía telefónica cuando se desconecte permanentemente su teléfono de la línea. 2 Derechos de la Compañía Telefónica Si su equipo causase algún problema en su línea que pudiera dañar la red telefónica, la compañía telefónica siempre que sea posible le avisará de la posible interrupción temporal de su servicio. En caso que la compañía no pudiera avisarle de antemano y hubiera necesidad de tomar tal acción, la compañía telefónica podrá interrumpir su servicio inmediatemente. En caso de tal interrupción telefónica temporal la compañía debe : (1) darle aviso al momento de tal interrupción temporal de servico, (2) concederle a Ud. la oportunidad de corregir la situación, (3) informarle a Ud. de sus derechos de presentar una questa a la Comisión de acuerdo con los procedimientos dictados en la Subparte E de la Parte 68 de las Regulaciones y Reglas de la FCC. La compañía telefónica puede hacer los cambios en sus instalaciones de comunicación, en equipos, en sus funcionamientos o procedimientos que digne necesarios para el manejo de sus negocios y que no sean incompatibles con las Reglas y Regulaciones de l a FCC. Si estos cambios pudieran alterar el uso o el funcionamiento de su equipo telefónico, la compañía telefónica deberá darle aviso adecuado en escrito para que Ud. goce de un servico ininterrumpido. INFORMACIÓN DE INTERFERENCIAS Este artefacto cumple con la Parte 15 de las Reglas de la FCC. Su funcionamiento es sujeto a las dos condiciones siguientes: (l) Este artefacto no puede causar interferencia dañosa, y (2) Este artefacto debe aceptar cualquier interferencia recibida, incluyendo interferencia que puede causar un funcionamiento no deseado. Este equipo ha sido probado y cumple con los límites para un artefacto digital de la Clase B, de conformidad con la Parte 15 de las Reglas de la FCC. Estos límites han sido diseñados para proporcionar una protección razonable contra una interferencia dañosa que pueda existir en una instalación doméstica. Este equipo genera, usa y puede radiar la energía de frecuencia de una radio y, si no fuera instalado y usado de acuerdo con las instrucciones, puede causar interferencia dañosa a las transmisiones radiales. Sin embargo, no hay garantía que la interferencia no ocurrirá en una instalación en particular. Si este equipo causa en efecto una interferencia dañosa a la recepción de la radio o de la televisión, lo cual puede ser determinado apagando y prendiendo el equipo, le animamos a Ud. de tratar de corregir la interferencia por medio de una (o más) de las sugerencias siguientes: • Cambie la posición o la ubicación de la antena (quiere decir la antena de la radio o de la televisión que está recibiendo la interferencia). • Cambie la posición o cambie la ubicación y aumente la distancia entre el equipo de telecomunicaciones y la antena receptora de la radio o de la televisión que está recibiendo la interferencia. • Conecte el equipo de telecomunicaciones a una toma en un circuito diferente del circuito al cual la antena receptora esté conectada. Si estas medidas no eliminan la interferencia, favor de consultar a su distribuidor o a un técnico de radio/televi sión experto por otras sugerencias. También, la Comisión Federal de Comunicaciones (FCC) ha preparado un folleto muy útil, “How To Identify and Resolve Radio/TV Interference Problems” (“Como Identificar y Resolver Problemas de Interferencia de Radio/Televisión”). Este folleto se puede obtener del U.S. Goverment Printing Office, Washington, D.C. 20402. Favor de especificar el número 004-000-00345-4 cuando haga su pedido. COMPATIBILIDAD CON AUDÍFONOS Se juzga que este teléfono es compatible con audífonos, en base a las normas de la FCC. 2 El número de la FCC está ubicado en el fondo de la base El numero REN esta ubicado en el fondo de la base TABLA DE CONTENIDO INFORMACIÓN DE LA REGISTRACIÓN DE LA FCC .............................................. 2 INFORMACIÓN DE INTERFERENCIAS ........... 2 COMPATIBILIDAD CON AUDÍFONOS ........... 2 INTRODUCCIÓN ............................................. 4 ANTES DE COMENZAR ................................... 5 LISTA DE PARTES ....................................... 5 REQUISITOS DE ENCHUFE MODULAR .............. 5 INSTALACIÓN Y PREPARACIÓN .......................... 6 INFORMACIÓN IMPORTANTE PARA LA INSTALACIÓN ............................................ 6 INSTALACIÓN DE LAS BATERÍAS ................... 6 INSTALACIÓN SOBRE SUPERFICIE PLANA ........ 8 INSTALACIÓN SOBRE PARED ........................ 9 PARA PROGRAMAR EL MENÚ DEL IDENTIFICADOR DE LLAMADAS ................... 10 PARA PROGRAMAR SU CLAVE DE AREA LOCAL ................................. 11 PARA PROGRAMAR EL IDIOMA DEL IDENTIFICADOR DE LLAMADAS EN LA PANTALLA ................................. 12 PARA PROGRAMAR ELCONTRASTE DE LA PANTALLA ............................. 13 PARA PROGRAMAR LA MODALIDAD P ARA MARCAR ................................. 14 PARA SALIR DE PROGRAMACION ........... 14 SUMMARY SCREEN ................................. 15 IDENTIFICADOR DE LLAMADAS CON LLAMADA EN ESPERA ................................................. 15 CALLER ID FEATURES .................................. 15 PARA RECIBIR Y ALMACENAR LLAMADAS ..... 16 PARA REVISAR LA INFORMACIÓN DE LAS LLAMADAS ............................................. 16 PARA BORRAR INFORMACIÓN DE LAS LLAMADAS ............................................ 17 PARA DISCAR (CONTESTANDO UNA LLAMADA)17 SI USTED PROGRAMÓ SU CÓDIGO DE ÁREA EN EL MENÚ DE PROGRAMACIÓN 18 SI USTED NO PROGRAMÓ SU CÓDIGO DE PARA USAR EL ALTAVOZ ............................. 21 LOCALIZACIÓN DEL ALTAVOZ ..................... 21 USO DEL ALTAVOZ .................................. 21 FUNCIONES BÁSICAS DEL TELÉFONO .............. 22 PARA RECIBIR UNA LLAMADA .................... 22 PARA HACER UNA LLAMADA ..................... 22 PARA INTERCAMBIAR ENTRE ALTAVOZ Y AURICULAR .................... 22 TONO TEMPORARIO PARA DISCAR ........... 23 CONTROL DEL VOLUMEN .......................... 23 RE-DISCADO .......................................... 23 PARA VOLVER A MARCAR CON UN SOLO TOQUE .................................................. 24 EN ESPERA ........................................... 24 SERVICIOS ESPECIALES (“FLASH”) ......... 25 MEMORIA .................................................. 26 PARA ALMACENAR NÚMEROS DE MARCADO RÁPIDO ................................................. 26 PARA ALMACENAR NÚMEROS LLAMADOS FRECUENTEMENTE .................... 27 PARA REVISAR NÚMEROS ALMACENADOS EN LA MEMORIA ................. 27 NÚMEROS DE MARCADO RÁPIDO .......... 27 NÚMEROS LLAMADOS FRECUENTEMENTE ........................... 28 PARA CAMBIAR UN NÚMERO ALMACENADO .. 28 PARA BORRAR UN NÚMERO ALMACENADO ... 28 PARA ALMACENAR UNA PAUSA EN LA MEMORIA ............................................... 28 PARA MARCAR UN NÚMERO DE MARCADO RÁPIDO EN LA MEMORIA .......................... 29 PARA MARCAR NÚMEROS MARCADOS FRECUENTEMENTE ................................... 29 DETECCIÓN DE AVERÍAS ............................... 30 CUIDADO GENERAL DEL PRODUCTO ................. 32 CÓMO OBTENER SERVICIOS DE MANTENIMIENTO 32 INDICE ...................................................... 33 GARANTÍA LIMITADA .................................... 35 ÁREA LOCAL EN SU MENÚ DE 19 INDICADORES DE MENSAJES ......................... 20 CAUTION PROGRAMACIÓN .............................. WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. RISK OF ELECTRIC SHOCK DO NOT OPEN THE LIGHTNING FLASH AND ARROWHEAD WITHIN THE TRIANGLE IS A WA R N I N G S I G N ALERTING YOU OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERS E R V I C E A B L E PA R T S I N SIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF I M P O R T A N T INSTRUCTIONS A C C O M PA N Y I N G T H E P R O D U C T. SEE MARKING ON BOTTOM / BACK OF PRODUCT 3 INTRODUCCIÓN Su teléfono con Identificador de Llamadas almacena y muestra información específica, que proviene de su compañía telefónica local, para suscriptores del Identificador de Llamada o servicios similares para la identificación de la persona que llama. Usted debe suscribirse a alguno de estos servicios para poder utilizar este aparato. Su teléfono Identificador de Llamadas le permite: • Identificar quién es la persona que llama antes de que usted conteste el teléfono. • Ver la hora y la fecha de cada llamada entrante. • Grabar hasta 60 mensajes del Identificador de Llamadas en secuencia. • Saber quién llamó mientras usted no estaba. IMPORTANTE: Para poder usar esta unidad usted debe suscribirse, ya sea al Servicio de Nombre/Número de Caller ID estándar o al Servicio de Caller ID con Call Waiting. Para saber quién está llamando mientras usted está en el teléfono, usted debe suscribirse al Servicio de Caller ID con Call Waiting. 4 ANTES DE COMENZAR LISTA DE PARTES Asegúrese de que su paquete incluye los siguientes artículos: OPTIONS A B DELETE REVIEW DIAL Cable corto STORE 1 2 ABC 3 DEF 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER REDIAL VOLUME * HOLD # FLASH SPEAKER Cable de la línea telefónica Cable espiral Auricular Base REQUISITOS DE ENCHUFE MODULAR Se requiere un jack modular RJ11C, que es el tipo de jack más común y puede parecerse a la ilustración aquí. Si Ud. no tiene un jack modular, llame a su compañía telefónica local para información sobre la instalación del jack requerido. 5 INSTALACIÓN Y PREPARACIÓN INFORMACIÓN IMPORTANTE PARA LA INSTALACIÓN • Nunca instale el cableado del teléfono durante una tormenta de relámpagos. • Nunca toque alambres telefónicos o terminales que no estén aislados, a menos de que la línea telefónica haya sido desconectada en la interfaz de la red. • Sea cuidadoso cuando instale o modifique líneas telefónicas. INSTALACIÓN DE LAS BATERÍAS Su teléfono con Identificador de Llamadas usa 4 baterías alcalinas tamaño “AA” para recibir y almacenar datos del Identificador de Llamadas y para los números que usted usa para el discado de memoria. IMPORTANTE: Usted tendrá aproximadamente 60 segundos para cambiar las baterías antes de que los datos almacenados en la memoria se pierdan. Por favor lea las instrucciones antes de cambiar las baterías y tenga las baterías listas de antemano para ser cambiadas. 1. Si el cable de la línea está ya conectado, desconéctelo de la base del aparato. 2. Utilice un destornillador para empujar hacia arriba la puerta del compartimento de la batería en la parte de abajo de la base. 3. Introduzca las 4 baterías alcalinas tamaño “AA” como se muestra en el diagrama dentro del compartimento de la batería. 4. Vuelva a asegurar la puerta del compartimento de la batería en su sitio. 5. Si el cable de línea estaba previamente conectado, vuelva a asegurar el cable al aparato y verifique las localizaciones de la memoria. 6 NOTA: Si el símbolo de baja batería aparece en la pantalla, usted necesita cambiar las baterías. Es importante que usted cambie las baterías tan pronto como sea posible para retener la información de la operación del Identificador de Llamadas. Durante el tiempo en el que se reemplazan las baterías, un circuito de repuesto en el aparato retendrá su información almacenada durante hasta 60 segundos. Anote cualquier información almacenada que usted no quiera que se borre. IMPORTANTE: Si usted no va a utilizar su teléfono durante más de 30 días, saque las baterías para evitar que una posible fuga dañe el aparato. Compartimento de la Batería 7 INSTALACIÓN SOBRE SUPERFICIE PLANA 1. Conecte el cable espiral al auricular. Conecte el otro extremo al contacto en el costado de la base. Coloque el auricular en su sitio sobre la base. 2. Conecte el cable telefónico al contacto en la parte posterior de la base. Conecte el otro extremo en el contacto de la pared. 3. Ponga el selector del timbre (“RINGER”) en la base en la posición de volumen deseada. • HI = Pre-programado, sonido más alto. • LO = El sonido será más bajo. • OFF = El teléfono no timbrará. 1 2 3 8 INSTALACIÓN SOBRE PARED 1. Cuidadosamente voltee el teléfono. Separe la placa de montaje para pared de las ranuras superiores simplemente oprimiendo hacia adentro las lengüetas. Jale la placa para separarla del teléfono y gírela de manera que se vea como el diagrama de abajo de la página. Suavemente oprima la placa dentro de las ranuras inferiores hasta que escuche un chasquido indicando que han entrado en su sitio. 2. Alimente el cable de la línea a través de la ranuras para que la parte de abajo de la base quede plana y lista para ser montada sobre la pared. 3. Conecte el otro extremo del cable de línea al contacto de pared. 4. Coloque el auricular en su sitio sobre la base tan pronto como le sea posible para colgar el teléfono. 5. Conecte el cable espiral al auricular. Conecte el otro extremo al contacto en el costado de la base. 6. Deslice los postes para montaje de la base (en la parte de abajo del aparato) sobre la placa de montaje de la pared y deslice la base del aparato hacia abajo hasta que el teléfono esté colocado firmemente en su sitio. 7. Slip the mounting holes of the base (on bottom of unit) over the wall plate posts and slide the base down until the phone is firmly in place. 8. Ponga el selector del timbre (“RINGER”) de la base, en la posición de volumen deseada. • HI = Pre-programado, sonido más alto. • LO = El sonido será más bajo. • OFF = El teléfono no timbrará. 8 2 7 6 3 4 1 9 PARA PROGRAMAR EL MENÚ DEL IDENTIFICADOR DE LLAMADAS Botones para revisar (“REVIEW”) Botón para opciones (“OPTIONS”) Se recomienda que el teléfono no sea conectado a la pared mientras usted está programando el menú para el Identificador de Llamadas. Una llamada entrante puede anular un cambio si aún no había sido salvado. El teléfono debería estar mostrando “xx CALLS” antes de que usted pueda inscribir el menú de la programación. OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME 1. Oprima el botón de opciones (“OPTIONS”). La indicación “OPTIONS MENU”^ v ). 2. En este momento usted puede oprimir cualquiera de los botones de “REVIEW,” hacia arriba o abajo para localizar y elegir de entre las 6 las pantallas de menú disponibles, que son: * HOLD # FLASH SPEAKER AM PM Pantalla Sumario • #1 Menú para programar (“OPTIONS MENU”) ^ v • #2 Código de área local (“LOCAL AREA CODE”) (default- - -) [default es la información que viene programada de fábrica y prevalecerá mientras no se programe algo en su lugar] • #3 Idioma para el Identificador de Llamadas(“LANGUAGE”) [default Inglés] • #4 Contraste de la Pantalla ((LCD) CONTRAST”) [default 3] • #5 Modalidad de Discado -Tono o Pulso- (“T/P DIAL MODE”) [default Tono] • #6 Término o salida de Programación (“EXIT OPTIONS”) 3. Usted tiene 10 segundos después de oprimir cualquier tecla antes de que el teléfono regrese automaticamente a la Pantalla Resumen. 10 PARA PROGRAMAR SU CLAVE DE AREA LOCAL El teléfono usa el área local programada para determinar el formato de números que se muestra cuando se recibe una señal válida del Identificador de Llamadas, y también se usa para la función de rediscado (“Dialback”), para regresar un llamado. 1. Oprima el botón de opciones (“OPTIONS”). El visor muestra “OPTIONS MENU” ^ v . Botones para revisar (“REVIEW”) Botón para opciones (“OPTIONS”) OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER 2. Oprima el botón de revisar (“REVIEW”) y los botones hacia arriba o abajo hasta que el visor muestre “LOCAL AREA CODE”. 3. Para inscribir y cambiar el código de área, oprima el botón “OPTIONS” nuevamente. La pantalla muestra el código de área que está actualmente almacenado. El dígito del extremo izquierdo o un signo de menos (-) parpadeará, indicando que está listo para aceptar la entrada del código de área. 4. Oprima 1-9 en el teclado para el primer dígito. Para cancelar ese dígito, oprima las teclas “*” o “#.” 5. Cuando el dígito deseado está parpadeando, oprima cualquiera de los botones “REVIEW” para avanzar al siguiente dígito. 11 6. Repita los pasos 4 y 5 hasta que todos los dígitos de su código de área estén correctos. Si usted comete un error, usted puede simplemente repetir los pasos anteriores hasta que su código de área está programado. 7. Oprima el botón “OPTIONS” nuevamente para almacenar el código de área y regresar al visor que lee código de área local (“LOCAL AREA CODE”). PARA PROGRAMAR EL IDIOMA DEL IDENTIFICADOR DE LLAMADAS EN LA PANTALLA Este ajuste cambia las instrucciones del Identificador de Llamadas a ser mostrados en Inglés o Español. 1. Oprima el botón de opciones (“OPTIONS”). La indicación “OPTIONS MENU” ^ v aparecerá en el visor. Botones para revisar (“REVIEW”) Botón para opciones (“OPTIONS”) OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER 2. Oprima el botón de revisar (“REVIEW”) y flecha hacia arriba hasta que la indicación “LANGUAGE” aparezca en el visor. 3. Para inscribir y cambiar el idioma, oprima el botón de opciones (“OPTIONS”). El visor indicará el idioma actual. El idioma por omisión (pre-programado) es inglés. 4. Oprima cualquiera de los botones “REVIEW” para cambiar la programación. 5. Oprima el botón de opciones (“OPTIONS”) una vez más para almacenar esta programación y regresar a la pantalla de idioma del Identificador de Llamadas (“LANGUAGE”). 12 PARA PROGRAMAR ELCONTRASTE DE LA PANTALLA Este ajuste le permite lograr la optimización del contraste y el ángulo de visión del visor. 1. Oprima el botón de opciones (“OPTIONS”). En el visor aparecerá “OPTIONS MENU” ^ v . 2. Oprima el botón de revisar (“REVIEW”) y flecha hacia arriba hasta que la indicación de contraste (“(LCD) CONTRAST”) aparezca en el visor. 3. Para inscribir y hacer un cambio en el contraste, oprima el botón de opciones (“OPTIONS”). El visor mostrará el nivel actual de contraste. Hay 5 niveles de contraste, con el nivel pre-programado en 3. Botones para revisar (“REVIEW”) Botón para opciones (“OPTIONS”) OPTIONS A REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD 4. Oprima cualquiera de los botones “REVIEW” para cambiar el nivel programado. B DELETE # FLASH SPEAKER 5. Oprima el botón de opciones (“OPTIONS”) nuevamente para almacenar la programación y volver al visor que indica “(LCD) CONTRAST.” 13 PARA PROGRAMAR LA MODALIDAD PARA MARCAR Este ajuste le permite seleccionar la modalidad para discar en modalidad de tono (tone) o rotatorio (pulse). 1. Oprima el botón de opciones (“OPTIONS”). La indicación “OPTIONS MENU” ^ v aparecerá en el visor. 2. Oprima el botón para revisar (“REVIEW”) y flecha hacia arriba hasta que la selección de discado (“T/P DIAL MODE”) aparezca en el visor. 3. Para entrar y cambiar la modalidad de discado, oprima el botón de opciones (“OPTIONS”). El visor muestra la programación actual. La modalidad preprogramada es de tono. 4. Oprima cualquiera de los botones “REVIEW” para cambiar la programación. 5. Oprima el botón de opciones (“OPTIONS”) nuevamente para almacenar la programación y regresar al visor que lee “T/P DIAL MODE”. PARA SALIR DE PROGRAMACION Para salir del Menú de Programación después de que los cambios se han efectuado, usted puede salir de inmediato, seleccionando el menú “EXIT OPTIONS” y oprimiendo el botón para opciones (“OPTIONS”). 14 Botones para revisar (“REVIEW”) Botón para opciones (“OPTIONS”) OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER CALLER ID FEATURES SUMMARY SCREEN La Pantalla Resumen muestra la hora actual, fecha, y número de llamadas nuevas esperando ser revisadas. Esto se muestra hasta que los botones “REVIEW” u “OPTIONS” se oprimen, o un nuevo dato del Identificador de Llamadas es recibido. Dentro de 10 segundos de haber recibido la llamada nueva, la Pantalla Resumen se muestra y el indicador de LED para Llamada Nueva (“New Call”) parpadeará. AM PM Indicador de Llamadas Nuevas (“NEW CALL”) OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE NOTA: El número de llamadas nuevas se muestra hasta que todas las llamadas nuevas han sido revisadas. 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD IDENTIFICADOR DE LLAMADAS CON LLAMADA EN ESPERA Si es el caso que su compañía telefónica puede integrar los servicios de Identificador de Llamadas con Llamada en Espera, usted podrá ver quién está llamando cuando escuche el tono de espera. La información del identificador de llamadas aparecerá en el visor después de que usted escuche el tono. # FLASH SPEAKER Botón para servicios especiales (“FLASH”) • Oprima el botón para servicios especiales (“FLASH”) para poner a la persona con la que usted está hablando en espera y poder así contestar la segunda llamada entrante. 15 PARA RECIBIR Y ALMACENAR LLAMADAS Este aparato recibe y muestra información transmitida por su compañía telefónica local. Esta información puede incluir el número telefónico, fecha, y hora; o el nombre, número telefónico, fecha y hora. Este aparato puede almacenar hasta 60 llamadas para ser revisadas después. Cuando la memoria está llena, una llamada nueva automaticamente reemplazará a la más antigua en la memoria. La indicación “NEW ” aparecerá en la pantalla para las llamadas recibidas que no han sido revisadas. Botones para revisar (“REVIEW”) OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL PARA REVISAR LA INFORMACIÓN DE LAS LLAMADAS • Oprima el botón “REVIEW “ hacia abajo para recorrer la información de las llamadas desde las más nuevas hacia las más antiguas. • Oprima el botón “REVIEW “ hacia arriba para recorrer la información de las llamadas desde las más antiguas hacia las más nuevas. • Cuando todos los mensajes han sido revisados, la indicación “START/ END” aparece en el visor. 16 STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER PARA BORRAR INFORMACIÓN DE LAS LLAMADAS • Para borrar los datos mostrados en el visor, oprima y el botón para borrar (“DELETE”) una vez. • Para borrar todos los datos mientras los revisa, oprima y sostenga el botón para borrar (“DELETE”) durante aproximadamente 3 segundos. El aparato le preguntará si quiere borrar y la indicación (“DELETE ALL?”) aparecerá en el visor. Oprima el botón para borrar (“DELETE”) nuevamente para completar la orden. Botón para Discar (“DIAL”) Botón para borrar (“DELETE”) OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE PARA DISCAR (CONTESTANDO UNA LLAMADA) 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME Mientras revisa los datos del Identificador de Llamadas, usted puede marcar para contestar la llamada, marcando los números que se muestran en el visor, simplemente oprimiendo el botón para marcar (“DIAL”). * HOLD # FLASH SPEAKER Botón para el altavoz (“SPEAKER”) NOTA: Usted debe oprimir el botón “DIAL” antes de levantar el auricular. NOTA: Si unicamente “PICKUP PHONE” se muestra en la pantalla, no se puede hacer ningún otro cambio a ese número. La información enviada por la compañía telefónica se sabe que representa un número válido que se puede volver a marcar (utilizado unicamente en áreas muy limitadas). Una vez que usted levanta el teléfono u oprime el botón del altavoz (“SPEAKER”), el número será automaticamente marcado. 17 SI USTED PROGRAMÓ SU CÓDIGO DE ÁREA EN EL MENÚ DE PROGRAMACIÓN 1. Use los botones “REVIEW” hacia arriba o abajo para que el visor muestre el número que usted desea discar. • Si usted ve un número con 7 dígitos (por ejemplo 555-1234), entonces esa llamada fué recibida desde su misma área de larga distancia. Sin embargo, esto no garantiza que la llamada es “local”. • Si usted ve un número con 11 dígitos (por ejemplo 1-234-555-1234), entonces la llamada recibida no es proveniente de su misma área de larga distancia. Botones para revisar (“REVIEW”) Botón para opciones (“OPTIONS”) OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 2. Para ajustar el número telefónico, oprima el botón “OPTIONS”. Por ejemplo, un número local de 7 dígitos a menudo no puede ser discado porque requiere un formato de 10 u 11 dígitos. Oprima el botón “DIAL” repetidamente para recorrer a través de números de 7, 10 y 11 dígitos. 1 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD 7-dígitos: número telefónico de 7 dígitos (por ejemplo 555-5555) 10-dígitos: código de área de 3 dígitos + número telefónico de 7 dígitos(por ejemplo 425-555-5555) 11-dígitos: código de larga distancia 1 + código de área de 3 dígitos + número telefónico de 7 dígitos (por ejemplo 1 + 425-5555555) 18 2 # FLASH SPEAKER 3. Oprima el botón “DIAL” y el visor leerá “PICKUP PHONE”. Un temporizador de 10 segundos comenzará a contar en este momento en la esquina superior de la pantalla, haciéndole saber el tiempo que pasa hasta que el visor regresa al dato del Identificador de Llamadas. • Si usted ajusta el número a ser llamado, el temporizador se vuelve a programar después de cada ajuste. 4. Levante el auricular u oprima el botón “SPEAKER” antes de que el temporizador llegue a 0. La indicación “NOW DIALING” se muestra en la pantalla y el número es marcado. Botones para revisar (“REVIEW”) Botón para Discar (“DIAL”) OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL SI USTED NO PROGRAMÓ SU CÓDIGO DE ÁREA 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME LOCAL EN SU MENÚ DE PROGRAMACIÓN 1. Use los botones “REVIEW” hacia arriba o abajo para que el visor muestre el número que usted desea marcar. Usted verá únicamente números de 10 dígitos (por ejemplo 234-555-1234). * HOLD # FLASH SPEAKER 2. Vea los pasos 2 a 4 en la sección anterior para completar la secuencia de re-discado. 19 INDICADORES DE MENSAJES Los siguientes mensajes especiales indican el estado actual de un mensaje o del aparato: NO CALLS (NO HAY LLAMADAS) La memoria del Identificador está vacía. UNKNOWN CALL (NO HAY LLAMADAS) La llamada entrante no tiene servicio de Identificador de Llamadas o su área de servicio no está conectada con la suya. Si la indicación “UNKNOWN CALL” (llamada desconocida) aparece junto con el número que llama, la información del nombre para ese número no estaba disponible. BLOCKED CALL (LLAMADA BLOQUEADA) La persona haciendo la llamada entrante está registrada como “Número Privado” y sus datos de Identificador de Llamadas no serán revelados. ERROR (ERROR) La información de la persona que llama ha sido interrumpida durante la transmisión. NO DATA No se ha detectado la señal (NO HAY DATOS ACCESIBLES) del,Identificador de o el Identificador de Llamadas no ha sido activado. START/END (PRINCIPIO/ FINAL) Usted está al principio o al final del registro del Identificador de Llamadas. El poder de la batería está bajo. 20 PARA USAR EL ALTAVOZ LOCALIZACIÓN DEL ALTAVOZ Para el funcionamiento óptimo, evite lo siguiente: • Areas con mucho ruido de fondo. (El micrófono puede recoger estos sonidos y evitar que el altavoz pueda cambiarse a la modalidad para recibir sonido cuando usted termina de hablar). • Superficies afectadas por vibración. OPTIONS • Areas remetidas, como una esquina, abajo de una gaveta, o junto a un gabinete, los cuales pueden generar un efecto de eco. USO DEL ALTAVOZ Siga las siguientes especificaciones cuando utilice el altavoz: • El altavoz funciona en una forma similar a un radio de dos sentidos, en que usted puede unicamente escuchar o hablar al mismo tiempo. A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER Indicador de Teléfono con Altavoz Botones de volumen (“VOLUME”) • Quédese razonablemente cerca del teléfono para que pueda ser escuchado claramente por la persona con la que está hablando. • Usted puede ajustar el volumen del altavoz, simplemente oprimiendo cualquiera de los botones de volumen (“VOLUME”), sea para aumentar o para disminuir el volumen. • El indicador luminoso del altavoz se encenderá cuando el altavoz está siendo utilizado. 21 FUNCIONES BÁSICAS DEL TELÉFONO PARA RECIBIR UNA LLAMADA 1. Asegúrese de que el selector del timbre (“RINGER”) esté en la posición de “HI” o “LOW”. 2. Cuando el teléfono timbra y la información de la persona que llama se muestra en el visor, levante el auricular u oprima el botón de altavoz (“SPEAKER”) y comience su conversación. OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 3. Usted puede ajustar el volumen de la voz de la persona que llama, simplemente oprimiendo los botones para aumentar o diminuir el volumen (“VOLUME”). 4. Ponga el selector del timbre (“RINGER”) en la posición de apagado (“OFF”) cuando usted no quiera ser interrumpido por el timbre del teléfono. 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER Botón para el altavoz (“SPEAKER”) Botones de volumen (“VOLUME”) PARA HACER UNA LLAMADA 1. Levante el auricular u oprima el botón para el altavoz (“SPEAKER”) y espere al tono de marcar. 2. Marque el número al que usted desea llamar. 3. Usted puede ajustar el volumen de la voz de la persona que llama, simplemente oprimiendo los botones para aumentar o diminuir el volumen (“VOLUME”). PARA INTERCAMBIAR ENTRE ALTAVOZ Y AURICULAR Usted puede intercambiar entre altavoz y auricular mientras el teléfono está marcando un número, o en cualquier momento durante una conversación. • De Altavoz a Auricular — Levante el auricular. • De Auricular a Altavoz — Oprima el botón “SPEAKER”, y cuelgue el auricular. 22 TONO TEMPORARIO PARA DISCAR Si usted tiene servicio rotatorio de discado, usted puede temporalmente cambiar de servicio rotatorio a servicio de tono. Después de marcar el número telefónico, oprima y suelte el botón * en el teléfono. Esto le permite el acceso a servicios telefónicos que requieren la modalidad de discado por tono, como por ejemplo transacciones bancarias o servicios de larga distancia. Después de usted cuelga el auricular, el teléfono automaticamente regresa a la modalidad de discado rotatorio. Botón para re-discado (“REDIAL”) OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME CONTROL DEL VOLUMEN * HOLD # FLASH SPEAKER Esta función le permite incrementar el nivel de volumen en la bocina del auricular cuando usted está conversando con otra persona. Cuando sea necesario, oprima los botones para aumentar o disminuir el volumen (“VOLUME”). Botones de volumen (“VOLUME”) RE-DISCADO Si el número que usted marcó está ocupado, o si usted quiere volver a llamar al último número que usted marcó, oprima el botón para volver a marcar (“REDIAL”). El número se muestra en la pantalla y será marcado automaticamente. 23 PARA VOLVER A MARCAR CON UN SOLO TOQUE Si el último número al que usted llamó estaba ocupado, usted puede re-discar inmediatamente, simplemente oprimiendo el botón “REDIAL” sin haber colgado el auricular. NOTA : La función de Re-discado almacena en la memoria todos los números que usted oprima. Si usted oprime cualquier número después de haber discado el último número al que usted llamó (por ejemplo, cuando está teniendo acceso a un sistema de buzón de voz), esos números también serán discados cuando se use la función de Rediscado. Esto podría provocar que el teléfono quiera discar todos los números al mismo tiempo. EN ESPERA 1. Para poner una llamada en espera, oprima el botón de espera (“HOLD”) y cuelgue el auricular. (Si usted estuviera en la función de altavoz, el aparato automaticamente pone esta llamada en espera). El indicador de espera (“HOLD”) parpadea hasta que usted vuelve nuevamente a su conversación. 2. Para volver a su conversación, levante el auricular o el auricular de cualquier teléfono en esa línea u oprima el botón de altavoz (“SPEAKER”). 24 Botón para re-discado (“REDIAL”) OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER Botón e indicador para espera (“HOLD”) Botón para el altavoz (“SPEAKER”) SERVICIOS ESPECIALES (“FLASH”) Este botón se utiliza para activar los servicios especiales disponibles a través de su compañía telefónica local, como Llamada en Espera. Estos servicios generalmente requieren una tarifa mensual adicional. Si usted se suscribe a alguno de estos servicios, por favor refiérase a las instrucciones de la compañía telefónica con respecto al uso adecuado de este botón (“FLASH”). Refiérase a la sección de “Funciones del Identificador de Llamadas” para mayor información sobre Identificador de Llamadas con Llamada en Espera. 1. Mientras usted está en una conversación, otra persona llama y usted escucha un tono. 2. Oprima el botón de servicios especiales (“FLASH”) una vez y suéltelo. La primera conversación se pone en espera y la segunda llamada puede ser contestada. OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER Botón para servicios especiales (“FLASH”) 3. Oprima el botón “FLASH” nuevamente y suelte. La persona de la llamada original puede nuevamente ser atendida y la persona en la segunda llamada se pone en espera. 25 MEMORIA Antes de que usted almacene cualquier número telefónico en la memoria, asegúrese de que la modalidad de discado es correcta para el tipo de teléfono que usted está utilizando. La modalidad de discado preprogramada es de tono (touch-tone), así que si usted tiene servicio de pulso (rotatorio), usted tiene que cambiar primero la modalidad de discado. Vea “Para Programar la Modalidad de Discado.” Botones para Discado Rápido (“QUICK DIAL”) OPTIONS Botón para almacenar (“STORE”) A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL Los siguientes botones pueden ser almacenados dentro de cualquier localización de memoria: 0-9, *, # y una pausa (“PAUSE/ REDIAL”). Vea “Para borrar un número almacenado” y [Discado de Tono Temporario.” PARA ALMACENAR NÚMEROS DE 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER Botón para el altavoz (“SPEAKER”) MARCADO RÁPIDO 1. Levante el auricular u oprima el botón para el altavoz (“SPEAKER”). 2. Oprima el botón para almacenar (“STORE”). 3. Inscriba el número telefónico (hasta 20 dígitos). Si usted comete un error, cuelgue y repita el procedimiento para almacenar desde el principio. NOTA: El número no será llamado de hecho mientras esté en esta función. 4. Oprima el botón para almacenar (“STORE”). 5. Oprima la localización seleccionada para números de Discado Rápido A o B. 6. Cuelgue el auricular u oprima nuevamente el botón para altavoz (“SPEAKER”). 7. Escriba el nombre o número de la persona almacenado en esa localización de la memoria, en la tarjeta de directorio. 26 PARA ALMACENAR NÚMEROS LLAMADOS FRECUENTEMENTE 1. Levante el auricular u oprima el botón para el altavoz (“SPEAKER”). Botones para Discado Rápido (“QUICK DIAL”) Botón para almacenar (“STORE”) 2. Oprima el botón para almacenar (“STORE”). 3. Inscriba el número telefónico (el aparato no usará esta modalidad para discar el número). Si usted comete un error, cuelgue y repita el procedimiento para almacenar desde el principio. 4. Oprima el botón para almacenar (“STORE”). OPTIONS A REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 6. Cuelgue el auricular u oprima nuevamente el botón “SPEAKER.” 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD 5. Oprima 0-9 para la localización de la memoria. B DELETE # FLASH SPEAKER Botón para el altavoz (“SPEAKER”) 7. Escriba el nombre o número de la persona almacenado en la localización de la memoria, en la tarjeta de directorio. PARA REVISAR NÚMEROS ALMACENADOS EN LA MEMORIA NÚMEROS DE MARCADO RÁPIDO 1. Asegúrese de que el auricular esté colgado. 2. Oprima el botón de marcado rápido (“QUICK DIAL”) A o B. El número se muestra en la pantalla. 27 NÚMEROS LLAMADOS FRECUENTEMENTE 1. Asegúrese de que el auricular esté colgado. 2. Oprima el botón para marcar (“DIAL”). 3. Oprima los botones 0-9 para la localización de la memoria. El número se Botón para Discar (“DIAL”) muestra en la pantalla. Botón para almacenar (“STORE”) PARA CAMBIAR UN NÚMERO ALMACENADO Repita la secuencia para almacenar. El nuevo número reemplazará al número viejo en la localización de la memoria. OPTIONS A B DELETE REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE PARA BORRAR UN NÚMERO ALMACENADO 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME 1. Levante el auricular u oprima el botón del altavoz (“SPEAKER”). * HOLD # FLASH SPEAKER 2. Oprima el botón para almacenar (“STORE”). 3. Oprima nuevamente el botón para almacenar (“STORE”). Botón para altavoz (“SPEAKER”) Botón para rediscar (“REDIAL”) 4. Oprima la localización de la memoria (A, B, 0-9) a ser borrada. PARA ALMACENAR UNA PAUSA EN LA MEMORIA El botón de Rediscado (“REDIAL”) se convierte en función de pausa cuando el botón para almacenar (“STORE”) ha sido oprimido primero. Es válido unicamente cuando se está almacenando un número en localizaciones de memoria. Use el botón “PAUSE (REDIAL)” para introducir una pausa cuando un retraso es necesario en una secuencia de discado automatico. Por ejemplo, cuando usted debe marcar el 9 para obtener línea externa o cuando usted inscribe códigos de acceso a su compañía de larga distancia. 28 Usted puede necesitar ajustar el periodo de duración de la pausa. Puede ser ajustado de 1 a 9 segundos. La duración preprogramada es de 4 segundos. 1. Levante el auricular u oprima el botón del altavoz (“SPEAKER”). 2. Oprima el botón para almacenar (“STORE”). 3. Oprima 1-9 (1=1 segundo, 2=2 segundos, etc.). Botón para almacenar (“STORE”) Botones para Discado Rápido (“QUICK DIAL”) Botón para Discar (“DIAL”) OPTIONS A B DELETE 4. Oprima nuevamente el botón para almacenar (“STORE”). 5. Oprima el botón “PAUSE (REDIAL)” para salvar. PARA MARCAR UN NÚMERO DE MARCADO RÁPIDO EN LA MEMORIA REVIEW 12:30 10/19 315 - 555 - 1324 SMITH JOHN DIAL STORE 1 2 ABC 3 DEF REDIAL 4 GHI 5 JKL 6 MNO 7 PQ RS 8 TUV 9 WX YZ 0 PER VOLUME * HOLD # FLASH SPEAKER 1. Levante el auricular u oprima el botón del altavoz (“SPEAKER”). 2. Oprima la localización de marcado rápido (“QUICK CALL”) A o B. El número se muestra en la pantalla y es marcado automaticamente. Botón para altavoz (“SPEAKER”) Botón para rediscar (“REDIAL”) PARA MARCAR NÚMEROS MARCADOS FRECUENTEMENTE 1. Levante el auricular u oprima el botón del altavoz (“SPEAKER”). 2. Oprima el botón para discar (“DIAL”). 3. Oprima 0-9 para la localización de la memoria. El número se marca automaticamente. 29 DETECCIÓN DE AVERÍAS NO HAY TONO DE MARCAR • Cheque todo el cableado para asegurarse de que todas las conexiones están firmemente aseguradas y no dañadas. • Cheque el gancho de colgar (hook switch): ¿Regresa a su lugar completamente cuando el auricular es descolgado? EL VISOR ESTÁ EN BLANCO • Cambie las baterías. • Cheque que las baterías está adecuadamente instaladas. NO APARECE NINGUNA INFORMACIÓN EN EL VISOR CUANDO ENTRA LA LLAMADA • ¿Ordenó usted el servicio de Identificador de Llamadas de su compañía telefónica local? Este aparato requiere que usted se suscriba al servicio de Identificador de Llamadas para que funcione. • Asegúrese que espera al segundo timbre antes de contestar. SE MUESTRA UN ERROR EN EL MENSAJE • La palabra ERROR aparece en la pantalla si el aparato detecta algo que no sea la información válida del Identificador de Llamadas durante el período de silencio después del primer timbre. Este mensaje indica la presencia de ruido en la línea, o que un mensaje inválido ha sido enviado por la compañía telefónica local. EL TELÉFONO NO DA LÍNEA HACIA AFUERA • Cheque la modalidad de discado en el menú de programación. ¿Posiblemente está colocado en modalidad de tono, que puede no ser compatible con su servicio local de discado? 30 EL TELÉFONO NO TIMBRA • ¿Está el botón de timbre (“RINGER”) en la posición de apagado (OFF)? • ¿Está usted usando demasiadas extensiones en una línea? (El número total de extensiones en una línea deberá no ser mayor que el número “REN” -Número de Equivalencia de Timbrado para su área. Vea las especificaciones en la sección de la Comisión Federal de Comunicaciones -FCC-.) • Lleve a cabo el chequeo del primer problema (Número 1). ¿Está el gancho para colgar el auricular completamente oprimido cuando el auricular está colocado en la base? VOLUMEN DE VOZ EN LAS LLAMADAS ENTRANTES COMO EN LAS QUE SALEN MUY BAJO • ¿Están otras extensiones descolgadas al mismo tiempo? Si es así, esta es una condición normal porque el volumen disminuye cuando más extensiones se usan al mismo tiempo. EL TONO DE RE-ALIMENTACIÓN PALPITA MIENTRAS SE MARCA EN MODALIDAD ROTATORIA • Esto es normal porque la energía fluctúa mientras el teléfono pulsa. 31 CUIDADO GENERAL DEL PRODUCTO Para mantener su teléfono funcionando bien y con buena apariencia, observe las siguientes pautas: • Evite poner el teléfono cerca de calentadores (calefactores) de ambiente y dispositivos que generen interferencia eléctrica ejemplo, motores o lámparas fluorescentes). • No lo exponga a la luz solar directa o a la humedad. • No deje caer la extensión móvil y no maltrate el teléfono. • Nunca use un agente de limpieza fuerte ni un polvo abrasivo, ya que esto dañará el acabado. • Retenga el empaque original en caso de que necesite embarcar el teléfono en el futuro. CÓMO OBTENER SERVICIOS DE MANTENIMIENTO La FCC requiere que este producto sea sometido a servicios de mantenimiento solamente por el fabricante o por sus agentes de servicio autorizados. De acuerdo con los requerimientos de la FCC, los cambios o las modificaciones que no hayan sido expresamente aprobadas por Thomson Consumer Electronics podrían anular la autoridad que tiene el usuario de operar este producto. Para recibir instrucciones sobre cómo obtener servicios de mantenimiento, por favor consulte la garantía incluida en esta Guía, o llame a Información para el Usuario, 1-800-448-0329. Adjunte su recibo al folleto, para futura referencia, o anote la fecha en la que se compró o recibió este producto como regalo. Esta información será valiosa si se llegase a requerir durante el período de garantía. Fecha de compra __________ 32 Nombre de la tienda __________________ INDICE A L Antes de Comenzar 5 Lista de partes 5 Localización del Altavoz 21 C Caller ID Features 15 Cómo obtener servicios de mantenimiento 32 Compatibilidad con Audífonos 2 Control del volumen 23 Cuidado general del producto 32 M D Para almacenar números de marcado rápido 26 Para almacenar números llamados frecuentemente 27 Para almacenar una pausa en la memoria 28 Para borrar información de las llamadas 17 Para borrar un número almacenado 28 Para cambiar un número almacenado 28 Para discar (contestando una llamada) 17 Para hacer una Llamada 22 Para intercambiar entre Altavoz y Auricular 22 Para marcar números marcados frecuentemente 29 Para marcar un número de marcado rápido en la memo 29 Para Programar el Idioma Del Identificador de Llam 12 Para programar el Menú del Identificador de Llamad 10 Para Programar elContraste de la Pantalla 13 Para Programar la Modalidad para Marcar 14 Para Programar Su Clave De Area Detección de Averías 30 E En Espera 24 F Funciones Básicas del Teléfono 22 G Garantía limitada 35 I Identificador de Llamadas con Llamada en Espera 15 Indicadores de Mensajes 20 Información de Interferencias 2 Información de la Registración de la FCC 2 Información Importante para la Instalación 6 Instalación de las Baterías 6 Instalación sobre Pared 9 Instalación sobre Superficie Plana 8 Instalación y Preparación 6 Introducción 4 Memoria 26 N Números llamados frecuentemente 28 P 33 Local 11 Para recibir una Llamada 22 Para recibir y almacenar Llamadas 16 Para revisar números almacenados en la memoriaNúm 27 Para revisar la información de las llamadas 16 Para Salir de Programacion 14 Para Usar el Altavoz 21 Para volver a marcar con un solo toque 24 S R Uso del Altavoz 21 Re-discado 23 Requisitos de enchufe modular 5 34 Servicios Especiales (“FLASH”) 25 Si usted no programó su código de área local en su 19 Si usted programó su código de área en el menú de 18 Summary Screen 15 T Tono temporario para discar 23 U GARANTÍA LIMITADA Lo que cubre su garantía: • Cualquier defecto en material o mano de obra. Por cuánto tiempo después de la compra: • Un año. (El periodo de garantía para unidades arrendadas se inicia con la primera renta o 45 días de la fecha del embarque a la firma de arrendamiento, lo que ocurra primero). Lo que haremos: • Proporcionarle una unidad nueva o, a nuestra opción, una reacondicionada. • La unidad de intercambio quedará bajo garantía por el resto del periodo de garantía del producto original. Cómo hacer un reclamo de garantía: • Empaque bien la unidad, incluyendo todos los cables, etc., que originalmente venían con el producto. Se recomienda usar el cartón y materiales de empaque originales. • Incluya evidencia de la fecha de compra, como el recibo de pago. También escriba claramente su nombre, dirección y la descripción del defecto. Mande vía UPS o un servicio de paquetería equivalente a: Thomson Consumer Electronics, Inc. 11721 B Alameda Ave. Socorro, Texas 79927 • Pague cualquier cargo que le facture el Centro de Intercambio por servicio que no esté cubierto por garantía. • Asegure su paquete contra pérdida o daños. Thomson no acepta responsabilidad en caso de daños o pérdida durante el trayecto a Thomson. • Un aparato nuevo o uno remozado se le enviará con los cargos pagados. Lo que no cubre la garantía: • Instrucciones al cliente. (Su manual de propietario le proporciona la información con respecto a las instrucciones de operación y los controles del usuario. Para información adicional, pregunte a su distribuidor). • Ajustes de instalación y de preparación del servicio. • Baterías. • Daño por mal uso o negligencia. • Productos que han sido modificados o incorporados a otros productos. • Productos comprados o que han recibido servicio fuera de los Estados Unidos. • Desastres naturales, por ejemplo y sin limitarse a ellos, daños por relámpagos. Registro del Producto: • Por favor llene y envíe por correo la Tarjeta de Registro del Producto que se embarcó con su producto. Hará más fácil que hagamos contacto con usted si fuera necesario. No se requiere la devolución de la tarjeta para tener la cobertura de la garantía. Cómo se Relaciona la Ley Estatal a esta Garantía: • Esta garantía le da a usted derechos legales específicos y podrá tener otros derechos que varían de estado a estado. Si compró su producto fuera de los Estados Unidos: • Esta garantía no se aplica. Vea a su distribuidor para información sobre la garantía. 35 Modelo 29391A 15403020 (Rev. 1 E/S) 99-34 Printed in China P.O. Box 1976, Indianapolis, IN 46206 © 1999 Thomson Consumer Electronics, Inc. Trademark(s) ® Registered Marca(s) Registrada(s) ">

Public link updated
The public link to your chat has been updated.
Advertisement