JVC DVR LPT0923-001B User manual

JVC DVR LPT0923-001B User manual
Filename [DR-MH30EU_01Cov1.fm]
DR-MH30EU_00.book Page 1 Tuesday, June 29, 2004 5:41 PM
DVD & HDD VIDEO RECORDER
DR-MH30S/
DR-MH20S
CABLE/SAT
TV
OPEN/
CLOSE
TV AV
DVD
STANDBY ON
DVD
TV/CBL/SAT
18
VIDEO
HDD
DVD
TV
PR
CANCEL
AUX
MEMO/MARK
LIVE
DUBBING
EDIT
PROGRAMME
TV
TOP MENU
NAVIGATION
ENTER
RETURN
MENU
PREVIOUS
NEXT
SLOW
PLAY/SELECT
REC
STOP/ CLEAR
SLOW
PAUSE
JUMP
REC MODE
DISPLAY
ON SCREEN
HELP
HDD
DVD
VIDEO
SAT
VPS/PDC
SET UP
1 STANDBY/ON
AUDIO
SUBTITLE
ANGLE
LIVE CHECK
PROGRESSIVE
SCAN
PULL - OPEN
F1
DV
S-VIDEO
VIDEO
DV IN
L(MONO)-AUDIO-R
INSTRUCTIONS
LPT0923-001B
EN
Filename [DR-MH30EU_02Safety.fm]
DR-MH30EU_00.book Page 2 Tuesday, June 29, 2004 5:41 PM
2
EN
Masterpage:Left0
SAFETY FIRST
Safety Precautions
The rating plate and the safety caution are on the rear of the unit.
WARNING: DANGEROUS VOLTAGE INSIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION:
A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS
UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE UNIT CORRECTLY AS
INSTRUCTED.
WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO
NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE
DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE
INSIDE OF THIS UNIT.
IMPORTANT:
8 Please read the various precautions on page 2 and 3 before
installing or operating the unit.
8 It should be noted that it may be unlawful to re-record prerecorded tapes, DVDs, or discs without the consent of the
owner of copyright in the sound or video recording, broadcast
or cable programme and in any literary, dramatic, musical, or
artistic work embodied therein.
CAUTION:
8 When you are not using the unit for a long period of time, it is
recommended that you disconnect the power cord from the
mains outlet.
8 Dangerous voltage inside. Refer internal servicing to qualified
service personnel. To prevent electric shock or fire hazard,
remove the power cord from the mains outlet prior to
connecting or disconnecting any signal lead or aerial.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CLASS 1 LASER PRODUCT
● Manufactured under licence from Dolby Laboratories. “Dolby” and
double-D symbol are trademarks of Dolby Laboratories.
● “DTS” and “DTS Digital Out” are trademarks of Digital Theater
Systems, Inc.
● SHOWVIEW is a registered trademark of Gemstar Development
Corporation. The SHOWVIEW system is manufactured under licence
from Gemstar Development Corporation.
● This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must
be authorized by Macrovision Corporation, and is intended for home
and other limited viewing users only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
REPRODUCTION OF LABELS
WARNING LABEL INSIDE OF THE UNIT
Page 2
Tuesday, 29 June 2004 17:39
Filename [DR-MH30EU_02Safety.fm]
DR-MH30EU_00.book Page 3 Tuesday, June 29, 2004 5:41 PM
Masterpage:Right+
SAFETY FIRST
For Italy:
“It is declared that this product, brand JVC, conforms to the
Ministry Decree n. 548 of 28 Aug.’95 published in the Official
Gazette of the Italian Republic n. 301 of 28 Dec.’95”
The STANDBY/ON 1 button does not completely shut off
mains power from the unit, but switches operating current on and
off. “`” shows electrical power standby and “!” shows ON.
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly.
Failure to heed the following precautions may result in
damage to the unit, remote control or disc.
1. DO NOT place the unit —
— in an environment prone to extreme temperatures or
humidity.
— in direct sunlight.
— in a dusty environment.
— in an environment where strong magnetic fields are
generated.
— on a surface that is unstable or subject to vibration.
2. DO NOT block the unit’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the unit or remote control.
4. DO NOT place anything which might spill on top of the unit
or remote control.
(If water or liquid is allowed to enter this equipment, fire or
electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with
water. Also DO NOT place any containers filled with water or
liquids (such as cosmetics or medicines, flower vases, potted
plants, cups, etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted
candles, on the apparatus.
8. AVOID violent shocks to the unit during transport.
Page 3
EN
3
MOISTURE CONDENSATION
Moisture in the air will condense on the unit when you move it from
a cold place to a warm place, or under extremely humid
conditions—just as water droplets form on the surface of a glass
filled with cold liquid. In conditions where condensation may occur,
disconnect the unit’s power plug from the wall and keep it
disconnected for a few hours to let the moisture dry, then turn on
the unit.
ATTENTION:
To mobile phone users:
Using a mobile phone in the vicinity of the unit may cause picture
vibration on the TV screen or change the screen to a blue back
display.
On placing the unit:
Some TVs or other appliances generate strong magnetic fields.
Do not place such appliances on top of the unit as it may cause
picture disturbance.
Tuesday, 29 June 2004 17:39
Filename [DR-MH30EU_02Safety.fm]
Masterpage:Left0
DR-MH30EU_00.book Page 4 Tuesday, June 29, 2004 5:41 PM
4
EN
CONTENTS
DISC INFORMATION
5
About Discs ...................................................................................5
INDEX
10
INSTALLING YOUR NEW UNIT
17
Basic Connections ......................................................................17
INITIAL SETTINGS
18
Auto Set Up .................................................................................18
Preset Download .........................................................................19
Language ....................................................................................21
Monitor Set ..................................................................................22
SAT CONTROL SET
23
Satellite Receiver Control Setting ...............................................23
BASIC OPERATIONS ON DVD DECK
25
Basic Playback ............................................................................25
Playback Features ......................................................................26
Using The On-screen Bar ...........................................................30
Parental Lock ..............................................................................34
Basic Recording ..........................................................................35
Recording Features .....................................................................36
BASIC OPERATIONS ON HDD DECK
38
Basic Recording ..........................................................................38
Recording Features .....................................................................39
Basic Playback ............................................................................40
Playback Features ......................................................................40
Live Memory Playback ................................................................41
TIMER RECORDING
44
ShowViewTM Timer Programming .............................................44
Manual Timer Programming ........................................................46
Automatic Satellite Programme Recording .................................48
NAVIGATION
EDITING
56
High Speed Dubbing (From HDD To DVD) ................................ 56
Just Dubbing (From HDD To DVD) ............................................ 56
Manual Dubbing (From HDD To DVD) ....................................... 57
Original Dubbing (From DVD To HDD) ...................................... 57
DV Dubbing ................................................................................ 58
Edit From A Camcorder .............................................................. 59
Edit To Or From Another Recorder ............................................ 60
Output/Input Set ......................................................................... 61
Digital Audio Dubbing ................................................................. 62
REMOTE CONTROL
63
Remote Control Functions .......................................................... 63
SYSTEM CONNECTIONS
65
Connecting To A Satellite Receiver ............................................ 65
Connecting To A Dolby Digital Decoder Or An Amplifier With
Built-in DTS .......................................................................... 66
SUBSIDIARY SETTINGS
67
Mode Set .................................................................................... 67
Scan Mode Set ........................................................................... 69
ShowViewTM System Setup ...................................................... 70
Tuner Set .................................................................................... 70
Clock Set .................................................................................... 73
Format A Disc (DVD Deck Only) ................................................ 74
Finalise A Disc (DVD Deck Only) ............................................... 75
Help Function ............................................................................. 76
Tray Lock (DVD Deck Only) ....................................................... 76
TROUBLESHOOTING
77
SPECIFICATIONS
81
APPENDIX
82
LIST OF TERMS
86
49
Library Database Navigation .......................................................49
Modify Original Information .........................................................50
Modify Play List Information ........................................................52
Modify Library Information ...........................................................54
Playback With MP3/WMA/JPEG Navigation ...............................55
Page 4
Tuesday, 29 June 2004 17:39
Filename [DR-MH30EU_03DiscInfo.fm]
Masterpage:Right0
DR-MH30EU_00.book Page 5 Tuesday, June 29, 2004 5:41 PM
DISC INFORMATION
About Discs
Recordable/playable Discs
You can use discs with the following logos for recording and
playback.
EN
5
DVD-R/RW Discs
It is only possible to use DVD-R discs which conform with DVD-R
standard Version 2.0.
When a DVD-R/RW disc (Video mode) is finalised (墌 pg. 75), it
can be played back on a standard DVD player as a DVD VIDEO
disc.
When a DVD-RW disc (VR mode) is finalised (墌 pg. 75), it can be
played back on a standard DVD player compatible with the VR
mode of DVD-RW discs.
Before finalising —
— it is possible to record on unrecorded areas of the disc, edit the
disc title and programme titles, and delete programmes.
DVD-RAM
12 cm: 4.7 GB/9.4 GB
8 cm: 1.4 GB/2.8 GB
Ver. 2.0/2x speed
Ver. 2.1/1x – 2x speed
DVD-RW
12 cm: 4.7 GB/9.4 GB
Ver. 1.1/1x – 2x speed (Video
mode/VR mode)
DVD-R
12 cm: 4.7 GB
8 cm: 1.4 GB
Ver. 2.0/1x – 4x speed (Video
mode)
● The above table is based on the information as of February 2004.
● Recording and playback may not be performed depending on the
characteristics and condition of the disc used, leading to
unsatisfactory results. Using discs manufactured by JVC is
recommended since they have been tested to be compatible with this
unit.
DVD-RAM Discs
It is only possible to use discs which conform with DVD-RAM
standard Version 2.0 or 2.1.
● It is impossible to record on DVD-RAM discs which do not conform to
this standard. If you use a disc formatted under a different standard
version, format it on this unit before use.
● It may not be possible to record, play back, edit or dub a DVD-RAM
disc even if it conforms to the standard if it was recorded or edited on
the devices from other manufacturers or on a PC, or if it has far too
many titles, or if there is very little available capacity remaining on the
disc.
● DVD-RAM discs recorded on this unit cannot be played back on an
incompatible DVD player.
● It is possible to record copy-once programmes of digital broadcasts
only onto 4.7/9.4 GB DVD-RAM discs (2.8 GB DVD-RAM discs are
not compatible).
Page 5
● It is impossible to record or edit DVD-R/RW discs recorded on other
devices even if they have not been finalised.
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
programme is deleted from a DVD-R disc.
After finalising —
After a DVD-R/RW disc (Video mode) has been finalised, it is
possible to play back the recorded programmes (video and/or
audio) on a standard DVD video player as a DVD VIDEO disc.
● Edited titles are displayed as the
“DVD menu” in video mode.
● It is impossible to record, edit or
delete the data either in video
mode or in VR mode.
● Either in video mode or in VR
mode, although the disc can be
played back on DVD players from
other manufacturers, sometimes it
may not be possible to play back
depending on the disc and recording conditions.
● It is impossible to record on CD-R/RW or DVD-R discs used for
authoring.
● It is impossible to record onto DVD-R/RW (Video mode) discs
broadcasts that allow you to copy once. The copy once programmes
can only be recorded onto DVD-RW discs formatted in VR mode.
NOTE:
The following may result if you play back a DVD-R disc recorded on
another unit.
● The disc does not play.
● A mosaic pattern (block noise) appears on the screen.
● Video or audio may be dropped out.
● The unit stops during playback.
Tuesday, 29 June 2004 17:39
Filename [DR-MH30EU_03DiscInfo.fm]
Masterpage:Left+
DR-MH30EU_03DiscInfo.fm Page 6 Monday, July 5, 2004 12:16 PM
6 EN DISC INFORMATION
Discs For Playback Only
Unplayable Discs
You can use discs with the following logos for playback only.
DVD VIDEO
Video CD/Super Video CD
The following types of discs cannot be played using this unit.
Do not attempt to play back any kind of disc that is damaged
(cracked, warped, or repaired with adhesive tape) or discs in
unusual shapes (heart-shaped, octagonal, or other forms). If such
discs are accidentally played back, it may cause noise that can
lead to speaker damage.
●
●
●
●
(example of region code
indications)
CD-ROM discs (including PHOTO-CD and CD-G)
Discs recorded in Packet Write (UDF) format
1.3-GB double density CDs (DDCD)
High density CDs (HDCD)
The following discs also cannot be played back.
● Discs of a region number other than “2”
● DVD-RAM (2.6 GB/5.2 GB)
● DVD-RAM (TYPE1)
Audio CD
CD-DA files
CD-RW
CD-DA/JPEG/
MP3 files
CD-R
CD-DA/JPEG/
MP3 files
CD-ROM
JPEG/MP3 files
● Playback may not be performed depending on the characteristics and
condition of the disc used.
● DTS Audio CDs can also be played back (An optional DTS decoder is
required).
● MP3 and JPEG discs can be played back on this unit only when they
have been recorded in the ISO9660 or Joliet format and finalised.
● JPEG files that can be played back on this unit must conform to JFIF/
Baseline process, and the maximum resolution of a JPEG file is
2,812 x 2,112 pixels.
● CD-R/RW discs recorded in music CD format need to be finalised to
play back on this unit.
● Operation and audio quality of this unit are not guaranteed for discs
that do not conform to the Compact Disc specification (CD-DA).
Before you play back a CD, check for the CD logo and read the notes
on the package to confirm that it conforms to the Compact Disc
specification.
● Depending on the intentions of the author of the software, recording
conditions of DVD discs and Video CD/SVCD discs may be
restricted. Since this unit plays back discs according to the intentions
of the author of the software as indicated on the disc, some functions
may not operate as commanded.
● When switching from the first layer to the second layer of doublelayered DVD VIDEO discs, the image and sound may be momentarily
distorted. This is not a malfunction.
● DVD-AUDIO discs compatible with DVD video players can be played.
● Super Audio CDs (SACD) compatible with conventional CD players
can be played.
Page 6
Region Number
The world is divided into 6 regions for DVD VIDEO discs.
DVD VIDEO discs are assigned a region number to indicate which
region they may be played back in. A disc cannot be played back
on this unit unless the region number of the disc matches that of
the unit. The region number for this unit is “2”. Only discs whose
region number includes “2” or “ALL” can be played back such as
shown below.
Examples of DVD VIDEO labels which can be played back
using this unit.
Marks of discs in this instruction manual
Allows operation with a
DVD-RAM disc.
Allows operation with a
Video CD/Super Video
CD (SVCD) disc.
Allows operation with a
DVD-R disc.
Allows operation with
an Audio CD disc.
Allows operation with a
DVD-RW disc.
Allows operation with a
disc including MP3
files.
Allows operation with a
DVD VIDEO disc.
Allows operation with a
disc including JPEG
files.
Monday, 5 July 2004 12:15
Filename [DR-MH30EU_03DiscInfo.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 7 Tuesday, June 29, 2004 5:41 PM
DISC INFORMATION
Recording Medium And Format
DVD-RAM
● Recording and erasing can be performed as many times as possible
on a disc.
● Editing can be performed after recording, such as deleting unwanted
parts.
● While recording, it is possible not only to start playback of a
programme currently being recorded, but also to watch another
programme previously recorded.
EN
7
Audio CD/Video CD/SVCD
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video CD/
SVCD discs.
However, some discs are not divided into tracks.
S
Audio CD or Video CD/SVCD
Track 1
Track 2
Track 3
Track 4
DVD-RW (VR mode)
● Recording and erasing can be performed as many times as possible
on a disc.
● Editing can be performed after recording, such as deleting unwanted
parts.
DVD-RW (Video mode)
● Can be played back on other DVD players.
● New recording can be performed by erasing all the data on a disc
once played back.
JPEG/MP3 Disc (CD-R/RW/ROM)
MP3/JPEG files put in directories nested in several levels on a disc
will be organized as if they were put in single level directories
(groups) by the MP3/JPEG Navigation of this unit. (墌 pg. 55)
File structure of a disc before starting the MP3/JPEG
Navigation
DVD-R
● Can be played back on other DVD players.
● Suitable when keeping a recorded disc for a long time.
File Structure Of Discs
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
“titles”. Each title has a number (title number) that can be used to
select desired titles. Titles are further divided into units called
“chapters”. Each chapter has a number (chapter number) that can
also be used to select desired chapters. Note that some discs are
not divided into titles and chapters.
When you record a programme on a DVD-RAM/RW (VR mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes from monaural to stereo
due to commercial breaks, etc. It is also possible to insert chapter
marks at desired locations during playback. (墌 pg. 27)
Directory
MP3 file
JPEG file
File structure of the disc after starting the MP3/JPEG
Navigation
Files are automatically grouped as follows and displayed on the
MP3/JPEG Navigation screen. Data is displayed in the
alphabetical order of file name. Files are grouped based on roots.
When you record a programme on a DVD-R/RW (Video mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes due to commercial breaks,
etc. It is also possible to insert chapter marks at desired locations
during either recording or playback. Once the disc has been
finalised, these chapter marks are deleted and new chapter marks
are assigned automatically approximately every 5 minutes.
DVD-RAM, DVD-RW, DVD-R or DVD VIDEO disc
Title 1
Chapter 1
Chapter 2
Title 2
Chapter 3
Chapter 1
Chapter 2
Chapter 3
● In Video mode, even before finalising, it is impossible to perform
editing operations other than changing the disc name and/or title
names and deleting programmes and/or titles.
● After finalising, it is impossible to perform editing operations.
● This unit can recognise up to 9 hierarchies including directories and
files.
Also, it can recognise up to 250 files in each group, and up to 99
groups on a disc.
NOTES:
● Video CD/SVCD discs that support Playback Control (PBC)
The contents of a disc are recorded into several hierarchies, and played
back according to the instructions on the screen while navigating through
the hierarchies. It is also possible to playback recorded tracks
consecutively without activating the PBC function even when playing a
PBC-compatible disc. (墌 pg. 29)
● Regarding the contents recorded on discs
Some files may not be played back depending on the file types and other
factors.
Page 7
Tuesday, 29 June 2004 17:39
Filename [DR-MH30EU_03DiscInfo.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 8 Tuesday, June 29, 2004 5:41 PM
8 EN DISC INFORMATION
DVD VIDEO Marks
Placing A Disc
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of the disc. Check the marks indicating the contents and
functions of the disc. Note, however, that in some cases a disc may
not include a mark even for a function it supports.
Opening the disc tray
Press x to open the disc tray.
Marks related to video
CABLE/SAT
TV
OPEN/
CLOSE
Number of subtitles
TV AV
Number of angles
HDD
DVD
STANDBY/ON
DVD
TV/CAL/SAT
VIDEO
DVD
HDD
DVD
TV
VIDEO
PULL - OPEN
F1
Recorded under the
standard 4:3 aspect
ratio
Screen includes black
bands at the top and
the bottom of image
which has a standard
4:3 aspect ratio (letter
box)
Video playback is in Wide video mode (16:9) on
wide televisions, but in letter box on televisions
with standard 4:3 aspect ratio.
Video playback is in Wide video mode (16:9) on
wide televisions, but pan and scan is used on
televisions with standard 4:3 aspect ratio (either
the left or right side of the image is cut-out).
DV
S-VIDEO
VIDEO
DV IN
L(MONO)-AUDIO-R
PR
● Pressing the button again closes the disc tray.
● Use the buttons to open and close the disc tray.
● Do not block the disc tray with your hand while it is opening or closing
as this may result in hardware failure.
● Do not place unplayable discs or any object other than a disc on the
disc tray.
● Do not press down strongly on the disc tray or place any heavy
objects on it.
Discs without cartridges
Marks related to audio
DVD
HDD
PULL - OPEN
VIDEO
Number of audio tracks
Y/ON
1 STANDB
Dolby Digital mark
It has been developed by Dolby Laboratories as
a digital surround system.
DTS (Digital Theater Systems)
You can enjoy DTS audio if you connect an
amplifier with a built-in DTS decoder to the
DIGITAL OUT connector of the unit.
Disc tray
Place the disc on the disc tray with the label side facing up. Since
disc size changes depending on the disc to be played back, be
sure to correctly align the disc with the grooves for its size. If the
disc is not in its groove, it may be scratched or otherwise damaged.
To insert an 8 cm disc, place it according to the inner groove.
DVD-RAM discs contained in cartridges
Double-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the side
you wish to play back or record facing down. If you insert the disc
with “Side A” facing down, programmes are recorded on the side A.
Single-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the label
side facing up.
Page 8
Tuesday, 29 June 2004 17:39
Filename [DR-MH30EU_03DiscInfo.fm]
DR-MH30EU_00.book Page 9 Tuesday, June 29, 2004 5:41 PM
Masterpage:Right+
DISC INFORMATION
EN
9
Care And Handling Of Discs
How to handle discs
When handling a disc, do not
touch the surface of the disc.
Since discs are made of
plastic, they are easily
damaged. If a disc gets dirty,
dusty, scratched or warped, the
images and sound will not be
picked up correctly, and such a
disc may cause the unit to malfunction.
Label side
Do not damage the label side, stick paper to or use any adhesives
on its surface.
Recording side
Make sure that discs are not scratched and dirty on the recording
side before use. Scratches and dirt on the recording side of a disc
may hinder proper playback and recording. Also be careful that a
DVD-RAM disc may get scratched or dirt when removed from
cartridge then put back in after use.
Storage
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt adhering
to a disc, wipe with a soft dry cloth, moving
from the centre outwards.
If a disc is difficult to clean, wipe with a cloth
moistened with water. Never use record
cleaners, petrol, alcohol or any anti-static
agents.
CAUTION:
Sometimes during playback, noise may appear or images may
be garbled. This is sometimes due to the disc. (It may not be up
to industry standards.)
These symptoms are caused by the discs, not by the malfunction
of the unit.
Page 9
Tuesday, 29 June 2004 17:39
Filename [DR-MH30EU_04Name.fm]
Masterpage:Left0
DR-MH30EU_00.book Page 10 Tuesday, June 29, 2004 5:41 PM
10 EN INDEX
Front View
A
B
C
D EFGH I J
HDD
DVD
VIDEO
1 STANDBY ON
F1
DV
S-VIDEO
K
A
B
C
D
E
F
G
H
I
J
Infrared Beam Receiving Window
Front Display Panel 墌 pg. 12
Disc Tray
Open/Close Button (x) 墌 pg. 8
Stop Button (8) 墌 pg. 25, 40
Play Button (4) 墌 pg. 25, 40
Pause Button (9) 墌 pg. 25, 40
Record Button (7) 墌 pg. 35, 38
HDD Button 墌 pg. 38
DVD Button 墌 pg. 25
L
VIDEO
DV IN
L(MONO)-AUDIO-R
M
N
OP
K Standby/On Button (1)
L Video Lamp (VIDEO) 墌 pg. 36, 39
M S-Video/Video/Audio Input Connectors (S-VIDEO/
VIDEO/AUDIO (L/R)) 墌 pg. 59
N DV Input connector (DV IN (i*)) 墌 pg. 58
* i (i.Link) refers to the IEEE1394-1995 industry specification and
extensions thereof. The i logo is used for products compliant with the
i.Link standard.
O HDD Lamp 墌 pg. 38
P DVD Lamp 墌 pg. 25
To access covered connectors, pull
and open the connector cover.
HDD
DVD
PULL - OPEN
DV
DV IN
L(MONO)-AUDIO-R
Page 10
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 11 Tuesday, June 29, 2004 5:41 PM
INDEX
EN
11
Rear View
A B
C
D
I
A Antenna Connectors (ANTENNA IN/OUT) 墌 pg. 17
B Component Video Output Connectors (COMPONENT
VIDEO OUT) 墌 pg. 17
C S-video Output Connector (S-VIDEO OUT) 墌 pg. 17, 60
D Audio Output Connectors (AUDIO OUT (RIGHT/LEFT))
墌 pg. 60
E AV COMPU LINK Connector*
E
J
K
F
G
H
L
H Mains Power Cord 墌 pg. 17
I L-1 Input/Output Connector (L-1 IN/OUT) 墌 pg. 17, 60,
61, 65, 66
J L-2 Input/Decoder Connector
(L-2 IN/DECODER) 墌 pg. 23, 60, 65, 66
K Satellite Control Connector (SAT CONTROL) 墌 pg. 23
L Region Number Label 墌 pg. 6
* Not function with this unit.
F Digital Audio Output Connectors
(DIGITAL OUT (COAXIAL/OPTICAL)) 墌 pg. 62, 66
G Cooling Fan
● This prevents the temperature from rising inside the unit.
Do not remove it.
● Install the unit so as not to block the area around the fan.
● The cooling fan on the rear of the unit may be activated even if
the unit is turned off in the following cases;
— In the Automatic Satellite Programme Recording standby
mode (墌 pg. 48), slightly before the starting time of VPS/PDC
recording (墌 pg. 45)
— If you connect the decoder or the satellite receiver to L-2 IN/
DECODER and if “L-2 SELECT” is set to “DECODER” or “SAT
VIDEO” or “SAT S-VIDEO”. (墌 pg. 61)
— when “JUST CLOCK” is set to “ON” (墌 pg. 73)
(Set “JUST CLOCK” to “OFF” if you mind the noise of the fan.)
Page 11
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 12 Tuesday, June 29, 2004 5:41 PM
12 EN INDEX
Front Display Panel
A
BCD
E
K
L
A VPS/PDC Indicator 墌 pg. 45
Appears when checking if the station being received transmits a
VPS/PDC signal.
Disc Type Indicator
When a disc is loaded, the type of the disc is indicated.
Disc Status Indicator
When a disc is running, the disc marks rotate.
During High-Speed Search: Rotate faster than normal playback.
During Slow Motion:
Rotate slower than normal playback.
While recording:
Inner red ring lights in the same way
as normal playback. During Instant
Timer Recording (ITR), inner red ring
slowly blinks.
While paused:
Disc marks blink when either
recording or playing back.
While stopped:
Disc marks all light.
While resume stopped:
Disc marks all blink.
While the disc tray opened:
Disc marks all light out.
No disc on the disc tray:
Disc marks all light out.
B VR Mode Indicator 墌 pg. 74
Lights when a DVD-RW disc is formatted in VR mode.
C Recording Mode Indicator (XP/SP/LP/EP/FR) 墌 pg. 35
Blinks when recording mode is being set.
While “FR” is blinking, the left 3 digits of the Multi Display (L M)
indicate setting values ranging from “60” to “480”. After the value
has been set, only “FR” lights.
D VPS/PDC Recording Indicator 墌 pg. 45
Lights when the VPS/PDC recording function is activated.
E Group/Title Indicator (GRP/TITLE)
“GRP” or “TITLE” lights depending on a disc loaded while the left 2
digits of the Multi Display (L) indicate the numbers explained below.
“GRP”:
Total number of groups or group number being played
back are displayed on the Multi Display.
“TITLE”: Total number of titles or title number being played back
are displayed on the Multi Display.
F Track/Chapter Indicator (TRK/CHAP)
“TRK” or “CHAP” lights depending on a disc loaded while the 3rd
and 4th digits from the left of the Multi Display (M) indicate the
numbers explained below.
“TRK”:
Total number of tracks or track number being played
back are displayed on the Multi Display.
“CHAP”: Chapter number being played back are displayed on the
Multi Display.
Page 12
F
M
G H
N
I
J
O
P
G Simulated Surround Effect Indicator (3D) 墌 pg. 32
Lights when a simulated surround effect is set to “3D-ON” on the
on-screen bar.
H Linear PCM Indicator (LPCM)
Lights when “XP MODE REC AUDIO” is set to “LINEAR PCM”
(墌 pg. 68) for recording with HDD, DVD-RAM, DVD-R and
DVD-RW discs, and when Linear PCM audio is played.
I Random/Programme Playback Mode Indicator (RND/
PRGM) 墌 pg. 33
“RND”:
Lights when Random Playback mode is set.
“PRGM”: Lights when Programme Playback mode is set.
J Repeat Mode Indicator (
/1/A–B) 墌 pg. 31
Select Repeat Playback mode on the on-screen bar.
“
”:
Whole disc is played back repeatedly.
“
1”:
A single title/chapter/track is played back repeatedly.
“
A–B”: The selected part (A–B) is played back repeatedly.
No display: Repeat Playback mode is off.
K Video Output Indicator (
) 墌 pg. 69
No display:Indicates that interlace mode is engaged.
:
Indicates that progressive mode is engaged.
(Example)
lights when video output mode is in progressive
mode.
L Group/Title Number Display
M Track/Chapter Number Display
N Remaining Time/Elapsed Time Indicator 墌 pg. 28, 36
Lights when remaining time of DVD-RAM, DVD-R and DVD-RW
discs is displayed, and lights out when elapsed time is displayed.
The right 6 digits of the Multi Display (O) indicate elapsed or
remaining time of each track.
No display: Indicates elapsed time of the disc.
Displayed: Indicates remaining time of the disc.
O Remaining Time/Elapsed Time Display 墌 pg. 28, 36
P Multi Display
Displays clock, received channel, elapsed time, and remaining time.
Also displays status of the unit (NO DISC/OPEN/CLOSE/
READING).
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 13 Tuesday, June 29, 2004 5:41 PM
INDEX
Remote Control
CABLE/SAT
TV
A
B
C
OPEN/
CLOSE
TV AV
DVD
STANDBY ON
DVD
TV/CBL/SAT
VIDEO
HDD
DVD
TV
V
W
X
Y
Z
D
PR
E
F
G
H
I
CANCEL
AUX
MEMO/MARK
LIVE
DUBBING
EDIT
TV
TOP MENU
NAVIGATION
J
K
L
M
N
O
P
Q
R
S
T
U
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
PROGRAMME
ENTER
MENU
RETURN
PREVIOUS
NEXT
SLOW
PLAY/SELECT
REC
STOP/ CLEAR
SLOW
PAUSE
JUMP
REC MODE
SAT
AUDIO
DISPLAY
ON SCREEN
VPS/PDC
SUBTITLE
HELP
SET UP
ANGLE
LIVE CHECK
a
b
c
d
e
Y
Z
a
b
c
d
e
f
g
h
i
j
f
g
k
l
h
i
j
k
l
m
n
o
p
q
m
n
o
p
q
r
PROGRESSIVE
SCAN
r
s
Open/Close Button (x) 墌 pg. 8
TV AV/VIDEO Button 墌 pg. 36, 39
HDD Button 墌 pg. 38
Number Keys 墌 pg. 23, 35, 38
Auxiliary Button (AUX) 墌 pg. 46, 70
Cancel Button (& (CANCEL)) 墌 pg. 44
Live Button (LIVE) 墌 pg. 42
Dubbing Button (DUBBING) 墌 pg. 56
TV Muting Button (TV ) 墌 pg. 63
Top Menu Button (TOP MENU) 墌 pg. 26
rt w e Buttons 墌 pg. 21
Menu Button (MENU) 墌 pg. 26
Reverse Skip Button (2) 墌 pg. 26, 42, 43
Previous Button (PREVIOUS) 墌 pg. 29
Reverse Search Button (3) 墌 pg. 26, 42
Reverse Slow Button (SLOW –) 墌 pg. 27
Record Button (7) 墌 pg. 35, 38
Jump Button (JUMP +/–) 墌 pg. 43
Recording Mode Button (REC MODE) 墌 pg. 35, 38
Display Button (DISPLAY) 墌 pg. 28, 36
Automatic Satellite Programme Recording Button
(SAT#) 墌 pg. 48
Page 13
S
T
U
V
W
X
s
EN
13
VPS/PDC Recording Button (VPS/PDC#) 墌 pg. 45
Audio Button (AUDIO) 墌 pg. 29
Subtitle Button (SUBTITLE) 墌 pg. 28
TV/CABLE/SAT/DVD switch 墌 pg. 21
DVD Standby/On Button (DVD 1)
TV/CBL/SAT Standby/On Button (TV/CBL/SAT 1)
墌 pg. 63
DVD Button 墌 pg. 25
TV Volume Buttons (TV%+/–) 墌 pg. 63
Programme Buttons (PR +/–) 墌 pg. 35, 63
Memo Button (MEMO) 墌 pg. 50, 53
Mark Button (MARK) 墌 pg. 27
Programming Button (PROGRAMME) 墌 pg. 44, 46, 47
Edit Button (EDIT) 墌 pg. 50
Navigation Button (NAVIGATION) 墌 pg. 49
Enter Button (ENTER) 墌 pg. 21
Return Button (RETURN) 墌 pg. 29, 44
Forward Skip Button (6) 墌 pg. 26, 42, 43
Next Button (NEXT) 墌 pg. 29
Forward Search Button (5) 墌 pg. 26, 42
Forward Slow Button (SLOW +) 墌 pg. 27
Play Button (4) 墌 pg. 25, 40
Select Button (SELECT) 墌 pg. 25, 50
Pause Button (9) 墌 pg. 25, 40
Stop Button (8) 墌 pg. 25, 40
Clear Button (CLEAR) 墌 pg. 31, 44
Skip Search Button (
) 墌 pg. 27, 42
Help Button (?) 墌 pg. 76
One Touch Replay Button (
) 墌 pg. 42
On-Screen Button (ON SCREEN) 墌 pg. 14, 30
Set Up Button (SET UP) 墌 pg. 21
Progressive Scan Button (PROGRESSIVE SCAN)
墌 pg. 69
Angle Button (ANGLE) (DVD deck only) 墌 pg. 28
Live Check Button (LIVE CHECK) 墌 pg. 42
How To Use
Before use, insert two R6 size batteries into the remote control
with the polarity ( and ) matched correctly as indicated on
the battery compartment or on the lid.
The remote control can operate most of your unit’s functions, as
well as basic functions of TV sets and satellite receivers of JVC
and other brands. (墌 pg. 63, 64)
● Point the remote control toward the receiving window.
● The maximum operating distance of the remote control is about
8 m.
NOTE:
If the remote control doesn’t work properly, remove its batteries, wait
a short time, replace the batteries and then try again.
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 14 Tuesday, June 29, 2004 5:41 PM
14 EN INDEX
On-Screen Display (DVD deck)
When pressing REC MODE
(Appears for eight seconds.)
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the
remote control is pressed, various operational indicators appear on
the TV screen. To clear the operational indicators, press ON
SCREEN twice.
RAM
FR360
7: 00
10: 00
20: 00
28: 00
36: 00
When playing back a recorded title
TITLE99 CHAPTER999 T. REMAIN6:59:59
XP
Digital
12
FISHING WORLD
A
B
C
D
E
F
G
H
I
J
K
Playback title number
Playback chapter number
Disc remaining time
Current status (playback)
Audio mode
Current received (recording) channel position number
(On playback background)
Bar meter
Name of title (or play list) currently being played back
Current playback point
Recorded mode
Live Memory mode (recording)
A
B
C
D
XP
SP
LP
EP
FR480
Disc type
Current recording speed
Remaining disc time for each recording speed
Recording speed
When pressing 7 during recording
ITR
2 : 30
A Recording time for Instant Timer Recording (ITR) mode
When recording
RAM
TITLE99 CHAPTER999 T. REMAIN6:59:59
11:35
12
FR360
A
B
C
D
Recording point
Current status (recording)
Current time
Recording channel number
Page 14
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 15 Tuesday, June 29, 2004 5:41 PM
INDEX
On-Screen Display (HDD deck)
FR360
11:00
12:00
1:00
FR360
11:35
12
11:33
STEREO
A Live Memory Recording point
B Live Memory Recording mode
When playing back a recorded title
1:00
15
When recording
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the
remote control is pressed, various operational indicators appear on
the TV screen. To clear the operational indicators, press ON
SCREEN twice.
0:00
EN
2:00 01:16:48
FR360
Digital
12
When pressing REC MODE
(Appears for eight seconds.)
STEREO
004 FISHING WORLD
FR360
A
B
C
D
E
F
G
H
I
J
K
Title start
Current playback point
Title end
Elapsed playing time
Play mode
Current received (recording) channel position number
(On playback background)
Recorded title (or play list) number currently being played back
Name of title currently being played back
Time scale (This title is an hour and a half long.)
Audio mode
Live Memory mode (recording)
When watching a programme on air
7: 00
10: 00
20: 00
28: 00
36: 00
A
B
C
D
XP
SP
LP
EP
FR480
HDD capacity graph
Current recording speed
Remaining HDD time for each recording speed
Recording speed
When pressing 7 during recording
ITR
2 : 30
A Recording time for Instant Timer Recording (ITR) mode
11:00
12:00
1:00
11:35
12
STEREO
ON AIR
A Possible start point from where Live Memory Playback can be
performed
B Possible start point from where Live Memory Recording can be
performed
(Received channel has changed at this point.)
C Currently viewed point
D Time scale
E Current time
F Current received channel position number
When using Live Memory playback
11:00
A
B
C
D
E
F
G
H
12:00
1:00
11:35
12
11:35
STEREO
Time scale for Temporary Recording
Current Temporary Recording point
Current time
Current playback channel position number
Time scale for Live Memory Playback
Current playback point
Live Memory playback mode
Current playback time
Page 15
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 16 Tuesday, June 29, 2004 5:41 PM
16 EN INDEX
On-Screen Display (DV Dubbing)
When capturing images from the external DV
equipment
HDD
A
B
C
D
E
F
G
H
I
J
K
0:00
1:00
FR360
00:00:00. 00
12bit
DV
JVC
2:00
GR-DV3500
DV
00:00:00. 00
L - R
SOUND1
GR-DV3500
Recording speed
HDD capacity graph
HDD time counter
Recording time scale
HDD mode
Remote control mode
Connected DV equipment mode
Connected DV equipment model information
Input channel
Sound mode
Sound input bit-rate*
* Indicates the sound bit-rate of the connected DV equipment
L Connected DV equipment information*
* Maker name and model name, etc. may not appear depending on the
connected equipment.
M Time counter for the connected DV equipment
N Sound monitor mode
DV
DV
1
2
O Remote control switch
P Auto capture button
Q Sound monitor switch
179 : 59 : 59
R Elapsed recording time
Page 16
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Right0
DR-MH30EU_00.book Page 17 Tuesday, June 29, 2004 5:41 PM
INSTALLING YOUR NEW UNIT
● The L-1 IN/OUT connector accepts and delivers either a composite
signal (regular video signal), Y/C signal or RGB signal.
● Set your TV to the VIDEO (or AV), Y/C, or RGB mode according to
the type of your TV’s SCART connector.
TV aerial cable
ANTENNA IN
Mains outlet
COMPONENT VIDEO OUT
S-VIDEO OUT
Mains power cord
Back of unit
L-1 IN/OUT
AUDIO OUT
Component
video cable
(not provided)
RF cable
(provided)
17
8 Basic Connection
To connect to a TV with 21-pin SCART input connector —
A Disconnect the TV aerial cable from the TV.
B Connect the TV aerial cable to the ANTENNA IN connector on
the rear panel of the unit.
C Connect the ANTENNA OUT connector on the rear panel of the
unit and the TV’s aerial connector with the provided RF cable.
D Connect the L-1 IN/OUT connector on the rear panel of the unit
and the TV’s 21-pin SCART connector with a provided 21-pin
SCART cable.
Basic Connections
ANTENNA
OUT
EN
Audio cable
(not provided)
21-pin SCART
cable
(provided)
S-Video
cable
(not
provided)
TV
It’s essential that your unit be properly connected.
ATTENTION:
Your TV must have a 21-pin AV input connector (SCART) for the
basic connection to the unit.
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
1 Make sure the package contains all of the accessories listed in
“SPECIFICATIONS” on page 81.
2 Place the unit on a stable, horizontal surface.
3 Connect the unit to a TV depending on the TV and cables you
8 S-Video Connection
To connect to TV’s S-VIDEO input and AUDIO input
connectors —
A Perform A – C in “Basic Connection”.
B Connect the unit’s S-VIDEO OUT connector to the TV’s
S-VIDEO input connector.
C Connect the unit’s AUDIO OUT connectors to the TV’s AUDIO
input connectors.
● You can obtain high-quality S-VHS pictures.
● With S-VIDEO connection, you cannot use the Preset Download
function. (墌 pg. 19)
● If your TV is not stereo-capable, use the unit’s AUDIO OUT
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
8 Component Video Connection
To connect to TV’s component video input connectors —
A Perform A – C in “Basic Connection”.
B Connect the unit’s COMPONENT VIDEO OUT connectors to
the TV’s component video input connectors.
C Connect the unit’s AUDIO OUT connectors to the TV’s AUDIO
input connectors.
● You can obtain high-quality component video pictures.
● If your TV is not stereo-capable, use the unit’s AUDIO OUT
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
● By using the component video connection, you can view the images
in the progressive mode. For switching to the progressive mode, refer
to “Scan Mode Set” (墌 pg. 69).
NOTE:
Select an appropriate option of “L-1 OUTPUT” as follows (墌 pg. 61):
When your TV’s SCART
connector accepts:
Set “L-1 OUTPUT” to:
Composite signals
“SCART VIDEO”
Y/C signal (separated
luminance (brightness) and
chrominance (colour) signals)
“SCART S-VIDEO”
RGB signal
“SCART RGB”
Component video signal
“COMPONENT”
4 Plug the end of the mains power cord into a mains outlet.
● “LOADING” blinks on the front display panel when the AC plug of the
mains power cord is connected into a mains outlet and it takes
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
use.
Page 17
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Left0
DR-MH30EU_00.book Page 18 Tuesday, June 29, 2004 5:41 PM
18
EN
INITIAL SETTINGS
3 Press rt w e to select the
Auto Set Up
Auto Channel Set/Auto Clock Set/Auto Guide Program
Number Set
After the 1 button on the unit (or DVD 1 on the remote
control) is pressed for the first time to turn on the unit, by simply
selecting your country*, the Auto Set Up function sets the tuner
channels, clock** and Guide Program numbers automatically.
* If you live in Belgium (BELGIUM) or Switzerland (SUISSE), you also
need to select your language.
** If you live in Hungary (MAGYARORSZÁG), Czech Republic (ČESKÁ
REPUBLIKA), Poland (POLSKA) or other countries in Eastern Europe
(OTHER EASTERN), set the clock manually.
1
CABLE/SAT
TV
DVD
INITIAL SET UP > LANGUAGE SELECT
language of your choice, then
press ENTER. The AUTO SET/
T-V LINK display appears on the
TV screen.
ENGLISH
DEUTSCH
FRANCAIS
ITALIANO
CASTELLANO
NEDERLANDS
SVENSKA
NORSK
SUOMI
DANSK
RETURN
4 Press w e to select “AUTO
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
INITIAL SET UP > AUTO CH SET
SET”, then press ENTER. The
AUTO SET screen will appear.
AUTO SET
ATTENTION:
SET UP
ENTER
EXIT
SELECT
T-V LINK
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
“AUTO” blinks on the front display
INITIAL SET UP > AUTO SET
panel; do NOT press any button on
the unit or remote control until the
front display panel shows “– –:– –”
AUTO SET
PLEASE WAIT...
as illustrated on page 20.
● When you have connected the unit
CANCEL
to a TV offering T-V Link via a
ENTER SELECT WITH [
SET UP
] THEN PRESS [ENTER]
fully-wired 21-pin SCART cable
PRESS [SET UP] TO EXIT
EXIT
SELECT
(墌 pg. 17) and the TV is turned
on, the unit automatically performs
the Preset Download (墌 pg. 19) even if you select “AUTO SET” for
Auto Set Up function.
ATTENTION:
Once you have performed Auto Set Up, even if the unit’s memory
backup has expired, all the stored stations and their Guide
Program numbers remain in the unit’s memory and the unit will
not perform Auto Set Up again. The unit only performs Auto
Clock Set when the unit is turned on.
If you have moved to a different area, perform each setting as
required.
● Tuner setting (墌 pg. 70)
● Clock setting (墌 pg. 73)
If a new station starts broadcasting in your area, perform tuner
setting. (墌 pg. 70)
DVD 1
ENTER
rtwe
NOTES:
Before starting, make sure of the following:
● The TV aerial cable should be connected to the unit.
● The unit’s mains power cord should be connected to a mains
outlet.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
● In areas where no TV station transmits a PDC (Programme Delivery
Control) signal, the unit can perform neither Auto Clock Set nor Auto
Guide Program Number Set.
● If there is a power cut, or if you press 1 or SET UP while Auto Set
Up is in progress, Auto Set Up will be interrupted; be sure to turn off
the unit power once and try again from step 1.
● Auto Clock Set may not function properly depending on the reception
condition.
● If no sound accompanies the picture or the audio sounds unnatural
on some channels that have been stored by Auto Set Up, the TV
system setting for those channels may be incorrect. Select the
appropriate TV system for those channels. (墌 pg. 72,
“INFORMATION”)
After “Auto Set Up” is completed, perform “Monitor Set” on
page 22.
1 Press 1 on the unit or DVD 1 on the remote control to turn on
the unit. The Country Set display appears on the TV screen.
2 Press rt w e to select your
country’s name, then press
ENTER. The Language Set
display appears on the TV screen.
NOTES:
INITIAL SET UP > AREA SELECT
BELGIUM
CESKA
DANMARK
DEUTSCHLAND
ESPANA
GREECE
ITALIA
MAGYARORSZAG
NEDERLAND
NORGE
OSTERREICH
POLSKA
PORTUGAL
SUISEE
SUOMI
SVERIGE
OTHER WESTERN
OTHER EASTERN
RETURN
● If you have selected BELGIUM or
ENTER SELECT WITH [
SET UP
] THEN PRESS [ENTER]
SUISSE, go to step 3.
PRESS [SET UP] TO EXIT
EXIT
SELECT
● If you have selected
MAGYARORSZÁG, ČESKÁ
REPUBLIKA, POLSKA or OTHER EASTERN, press ENTER. The
Clock Set screen appears. Set the clock manually (墌 pg. 73), then
go to step 4.
● If you have selected any other country name, go to step 4.
Page 18
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 19 Tuesday, June 29, 2004 5:41 PM
INITIAL SETTINGS
Preset Download
Auto Channel Set by Downloading from TV/Auto Clock
Set/Auto Guide Program Number Set
ATTENTION:
You can use this function only with a TV offering T-V Link, etc.* Be
sure to use a fully-wired 21-pin SCART cable.
* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART
cable. The degree of compatibility and available functions may differ by
system.
CABLE/SAT
TV
ENTER
we
DVD
EN
19
If you have connected the unit to your TV via a 21-pin SCART
cable (墌 pg. 17), the unit will automatically perform Preset
Download instead of the Auto Set Up in step 4 on page 18. After
downloading, the unit sets the clock and Guide Program numbers
automatically.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
● Perform steps 1 to 3 of “Auto Set Up” (墌 pg. 18) before continuing.
1 Press w e to select “T-V LINK”
and press ENTER. The T-V LINK
screen will appear.
ATTENTION:
Preset positions on the front display
panel increase from “PR 1”; do NOT
press any button on the unit or remote
control until the front display panel
shows clock time, “PR 1” or “– –:– –”
as illustrated on page 20.
● When Preset Download is
completed, “COMPLETED”
appears for about 5 seconds, then
the normal screen appears.
● If you press any button on the unit
or remote control while
downloading is in progress, it will
be interrupted.
INITIAL SET UP > AUTO CH SET
AUTO SET
SET UP
ENTER
EXIT
SELECT
T-V LINK
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
INITIAL SET UP > AUTO SET
AUTO SET
PLEASE WAIT...
CANCEL
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
NOTES:
● For details, refer to the instruction manual of your TV.
● In the area where no TV station transmits a PDC (Programme
Delivery Control) signal, the unit can perform neither Auto Clock Set
nor Auto Guide Program Number Set.
● If there is a power cut, or if you press 1 or SET UP while
downloading or set up is in progress, it will be interrupted; be sure to
turn off the unit power once and try again from the beginning.
● Auto Clock Set may not function properly depending on the reception
condition.
● On this unit, the characters available for station names (ID) are A–Z,
0–9, –, f, + and I (space). Some names of downloaded stations
may differ from those of your TV. (墌 pg. 72)
After “Preset Download” is completed, perform “Monitor Set” on
page 22.
Page 19
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 20 Tuesday, June 29, 2004 5:41 PM
20 EN INITIAL SETTINGS
Results Of Auto Set Up/Preset Download Appearing
On The Front Display Panel
If both Auto Channel Set and
Auto Clock Set have been
performed successfully, the
correct current time is displayed.
Turn on the TV and select its AV mode, then make sure that all
necessary stations have been stored in the unit’s memory by using
the PR +/– button(s).
● If station names (ID – 墌 pg. 85) have also been stored in the unit’s
memory, the station name will be displayed at the top right corner of
the TV screen for about 5 seconds when the unit is tuned to a
different station.
● If you want to set the tuner manually such as to add or skip channels,
to change channel positions, or to set or change station names, see
pages 71 – 72.
If Auto Channel Set has
succeeded but Auto Clock Set
has not, “PR 1” (channel
position) is displayed.
OR
If both Auto Channel Set and Auto Clock Set have failed,
“– –:– –” is displayed.
A Turn on the TV and select its AV mode, then make sure that all
necessary stations have been stored in the unit’s memory by
using the PR +/– button(s).
● If station names (ID – 墌 pg. 85) have also been stored in the unit’s
memory, the station name will be displayed at the top right corner of
the TV screen for about 5 seconds when the unit is tuned to a
different station.
● If you want to set the tuner manually such as to add or skip channels,
to change channel positions, or to set or change station names, see
pages 71 – 72.
B Perform “Clock Set” on page 73.
ATTENTION:
After making sure the cables are connected properly, turn off the unit’s
power once, then turn the unit’s power back on again.
The Country Set display appears on the TV screen; perform “Auto Set
Up” on page 18 or “Preset Download” on page 19 again.
IMPORTANT:
● To check if the Guide Program numbers have been set correctly,
perform the SHOWVIEW Timer Programming. (墌 pg. 44)
● In certain reception conditions, station names may not be stored
correctly, and auto Guide Program Number Set may not work
properly. If the Guide Program numbers are not set properly when
you timer-record a TV programme using the SHOWVIEW system, the
unit will record a TV programme of a different station. When
programming the timer using the SHOWVIEW system, be sure to
check the desired channel is selected correctly. (墌 pg. 44,
“ShowViewTM Timer Programming”)
● Your unit memorizes all detected stations even if reception of some of
them is poor. You can delete those stations with an unacceptable
picture. (墌 pg. 72, “Delete A Channel”)
Page 20
INFORMATION
Language for the on-screen display
Auto Set Up also selects the language automatically for the onscreen display depending on the Country setting you have made in
step 2 on page 18 (unless you have selected BELGIUM or
SUISSE), as shown below.
SUOMI
PORTUGAL
DEUTSCHLAND
POLSKA
NORGE
SVERIGE
DANMARK
ÖSTERREICH
ČESKÁ REPUBLIKA
]
]
]
]
]
]
]
]
]
SUOMI
ENGLISH
DEUTSCH
ENGLISH
NORSK
SVENSKA
DANSK
DEUTSCH
ENGLISH
ITALIA
MAGYARORSZÁG
ESPAÑA
NEDERLAND
GREECE
]
]
]
]
]
ITALIANO
ENGLISH
CASTELLANO
NEDERLANDS
ENGLISH
OTHER WESTERN ] ENGLISH
OTHER EASTERN ] ENGLISH
If you want to change the language setting manually, see “Onscreen Language Set” on page 21.
Just Clock
Your unit is equipped with the Just Clock function which provides
accurate time keeping through automatic adjustments at regular
intervals, by reading data from a PDC signal. If you want to take
advantage of this function, simply set it to “ON”. (墌 pg. 73)
T-V Link Functions
When you connect the unit to your TV via a fully-wired 21-pin
SCART cable (墌 pg. 17), the following functions are available. You
can use these functions only with a TV offering T-V Link, etc.*
For details, refer to the instruction manual of your TV.
* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART
cable. The degree of compatibility and available functions may differ by
system.
TV Auto Power On
The TV will turn on and be set to its AV mode automatically
whenever you start playback.
For details, refer to the instruction manual of your TV.
Unit Auto Standby
You can use your TV’s remote control to turn off the unit.
For details, refer to the instruction manual of your TV.
Direct Rec
You can easily start recording the programme that you are
watching on your TV. When you use this function, set “DIRECT
REC” to “ON”. (墌 pg. 68)
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 21 Tuesday, June 29, 2004 5:41 PM
INITIAL SETTINGS
EN
21
On-screen Language Set
Language
This unit offers you the choice to view on-screen messages in 10
different languages.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “FUNCTION SET UP”, then press t.
3 Press w e to select “DISPLAY
DVD VIDEO SET UP
CABLE/SAT
TV
DVD
SET”, then press t.
4 Press rt to select “ON
SCREEN LANGUAGE”, then
press ENTER.
5 Press rt to select your
desired language, then press
ENTER.
HDD/DVD SET UP
FUNCTION SET UP
DISPLAY SET
VIDEO IN/OUT
REC/PLAY SET UP
SUPERIMPOSE
INITIAL SET UP
AUTO
BLUE BACK
ON
DIMMER
BRIGHT
POWER SAVE
OFF
ON SCREEN LANGUAGE
SET UP
ENTER
EXIT
SELECT
ENGLISH
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
6 Press SET UP to complete the setting.
Menu/Audio/Subtitle Language Set (DVD deck only)
ENTER
rtwe
Some DVD discs contain the DVD menu display, audio and
subtitles in multiple languages. With these discs, you can set the
default language as you like.
● The procedure shows how to set “MENU LANGUAGE” as an
example.
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “DVD VIDEO SET UP”, then press t.
3 Press w e to select
DVD VIDEO SET UP HDD/DVD SET UP
SET UP
“LANGUAGE SET”, then press t.
4 Press rt to select “MENU
LANGUAGE”, then press ENTER.
5 Press rt to select your
desired language, then press
ENTER.
● See “Language Code List”
(墌 pg. 82).
LANGUAGE SET
AUDIO OUTPUT
MENU LANGUAGE
FUNCTION SET UP
INITIAL SET UP
PARENTAL LOCK
DISC SET UP
ENGLISH
AUDIO LANGUAGE
ENGLISH
SUBTITLE
ENGLISH
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
6 Press SET UP to complete the setting.
NOTE:
When the selected language is not available on the disc, the disc’s
default menu language is played back.
Page 21
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 22 Tuesday, June 29, 2004 5:41 PM
22
EN
INITIAL SETTINGS
1 Press SET UP to access the Main Menu screen.
Monitor Set
● You cannot set the monitor type during recording or playback.
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
2 Press w e to select “FUNCTION SET UP”, then press t.
3 Press w e to select “VIDEO IN/
DVD VIDEO SET UP HDD/DVD SET UP
OUT”, then press t.
4 Press rt to select “MONITOR
TYPE”, then press ENTER.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
5 Press rt to select the desired
CABLE/SAT
TV
DVD
option, then press ENTER.
6 Press SET UP to complete the
REC/PLAY SETUP
DISPLAY SET
FUNCTION SET UP
INITIAL SET UP
VIDEO IN/OUT
MONITOR TYPE
4:3LB
F-1 INPUT
VIDEO
L-1 OUTPUT
SCART VIDEO
L-2 INPUT
VIDEO
L-2 SELECT
VIDEO
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
setting.
* The boldface settings below indicate the settings at your
purchase.
8 MONITOR TYPE — 4:3LB / 4:3PS / 16:9 AUTO / 16:9 FIX
4:3LB (Letter Box conversion): Select this when the aspect ratio of
ENTER
rtwe
SET UP
your TV is 4:3 (conventional TV). While viewing a wide screen
picture, the black bars appear on the top and the bottom of the
screen.
4:3PS (Pan&Scan): Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide screen picture, the
black bars do not appear; however, the left and right edges of the
pictures will not be shown on the screen.
16:9 AUTO (Wide television conversion): Select this when the
aspect ratio of your TV is 16:9 (wide TV).
16:9 FIX (Wide television conversion): Select this when the aspect
ratio of your TV is fixed to 16:9 (wide TV). The unit automatically
adjusts the screen width of the output signal correctly when
playing back a picture whose aspect ratio is 4:3.
Pan&Scan/Letter Box
In general, DVD VIDEO disc are produced for a wide-screen TV
with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect ratio.
There are two styles to display the image, “Pan&Scan” (PS) and
“Letter Box” (LB).
Pan&Scan
The right and left side of the image are cut off.
The image fills the screen.
● The picture will be shown in the “4:3LB” mode
depending on the disc even if the “4:3PS” mode
is selected.
Letter Box
Black bands appear at the top and bottom of
the image. The image itself appears in 16:9
aspect ratio.
Page 22
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
Masterpage:Right0
DR-MH30EU_00.book Page 23 Tuesday, June 29, 2004 5:41 PM
SAT CONTROL SET
Satellite Receiver Control Setting
Satellite receiver
EN
23
The following procedure is required if you receive satellite channels
through a satellite receiver. Approximately 20 seconds before the
SHOWVIEW timer programming (墌 pg. 44) or Manual Timer
programming (墌 pg. 46) starts, the unit sets its input mode to “L-2”
and automatically switches the satellite receiver’s channels using
the provided Satellite Controller.
Installing Satellite Controller
1 Place the Satellite Controller so that the path between its
transmitter and the satellite receiver’s remote sensor is
unobstructed.
2 Fix securely using the adhesive strip attached on the back of the
Satellite Controller.
Satellite Controller
(provided)
(suggested locations)
Your unit
3 Be sure to connect the unit’s L-2 IN/DECODER connector to the
satellite receiver’s 21-pin SCART connector.
NOTE:
When connecting your satellite receiver, refer to its instruction manual.
Transmitter Satellite Controller
(provided)
4 Connect the Satellite Controller to the SAT CONTROL
connector on the rear panel.
Setting Satellite Receiver’s Brand And Channel
After installation, set the satellite receiver’s brand and channel
correctly; otherwise, the Satellite Controller cannot work correctly.
Satellite receiver
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
1 Turn on the satellite receiver’s power.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press t.
4 Press w e to select “TUNER
21-pin SCART cable
(provided)
DVD VIDEO SET UP HDD/DVD SET UP
SET”, then press t.
TUNER SET
5 Press rt w e to select “SAT
CONTROL SET”, then press
ENTER.
FUNCTION SET UP
AUTO CH SET
MANUAL CH SET
SAT CONTROL SET
GUIDE PROG SET
11
6 Press rt to select “BRAND”,
Back of unit
then press ENTER.
7 Press rt to select the brand
INITIAL SET UP
CLOCK SET
SET UP
ENTER
EXIT
SELECT
12
13
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
code from the list on page 24, then press ENTER.
● If the unit is in playback or recording mode, you cannot set the brand
code.
L-2 IN/DECODER
8 Press rt to select “PROGRAMME”, then press ENTER.
9 Press rt to select one of the channel positions on the satellite
SAT CONTROL
CABLE/SAT
TV
DVD
receiver, then press ENTER.
● You can select the channel position between 1 to 999.
10 Press rt to select “TEST”,
INITIAL SET UP > SAT CONTROL SET
then press ENTER. The unit enters
the Test mode.
BRAND
73
PROGRAMME
12
TEST
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
ENTER
rtwe
SET UP
Page 23
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_04Name.fm]
DR-MH30EU_00.book Page 24 Tuesday, June 29, 2004 5:41 PM
24
EN
Masterpage:Left+
SAT CONTROL SET
11 Check the result of the test.
If the satellite receiver’s channel number has been changed to
the same one as you set in step 9
Press w e to select “YES”, then press ENTER to finish the Sat
Control Set mode.
If the satellite receiver’s channel number has not been
changed correctly
Press w e to select “NO”, then press ENTER. Then perform the
procedure again from step 6.
BRAND NAME
CODE
JVC
AMSTRAD
ASTON
CANAL SATELLITE
CANAL +
D-BOX
ECHOSTAR (VIA DIGITAL)
FINLUX
FORCE
GALAXIS
GRUNDIG
HIRSCHMANN
HUMAX
ITT NOKIA
JERROLD
KATHREIN
LUXOR
MASCOM
MASPRO
NOKIA
PACE
PANASONIC
PHILIPS
RADIX
RFT
SABA
SAGEM
SALORA
SAMSUNG
SIEMENS
SKYMASTER
TECHNISAT
THOMSON
TPS
TRIAX
WISI
73
60, 61, 62, 63, 92
97
81
81
85
82
68
89
88
64, 65, 102
64, 78, 99
88
68
75
70, 71, 96
68
93
70
87, 94
65, 67, 74, 86, 92, 97
74, 92
66, 84, 101
78
69
97
83, 90
68
83
64
69, 98
66, 100
97
83
91
64
NOTES:
● The Satellite Controller may not work with all types of satellite
receiver.
● For some satellite receivers, you need to set its channel input mode
to 2-digit.
● If your satellite receiver has more than two channel modes, be sure to
set to “All Channel Mode”. For details, refer to the instruction manual
of the satellite receiver.
● When selecting the satellite receiver’s channel (墌 step 9), signals
from the remote control may interfere with signals transmitted from
the Satellite Controller. In this case, move the remote control as close
to the unit’s infrared beam receiving window as possible.
Page 24
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Right0
DR-MH30EU_00.book Page 25 Tuesday, June 29, 2004 5:41 PM
BASIC OPERATIONS ON DVD DECK
EN
25
To play back an MP3/JPEG disc, see “Playback With MP3/WMA/
JPEG Navigation” (墌 pg. 55).
Basic Playback
1 Load a disc.
● For details, refer to “Placing A Disc” (墌 pg. 8).
● Pressing 4 also closes the disc tray.
● Playback begins automatically if an auto-playback DVD disc is
loaded.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
2 Press DVD so that the DVD lamp lights up on the unit.
3 Press 4 to start playback.
DVD
4
x
8
9
CABLE/SAT
TV
DVD
x
DVD
● If you load a DVD disc whose region code does not match the unit,
“REGION CODE ERROR” appears on the TV screen. For details,
refer to “Region Number” (墌 pg. 6).
● If “CAN NOT PLAY BACK DISC UNDER CURRENT SETTING”
appears on the TV screen, refer to “Parental Lock” (墌 pg. 34).
● With Video CD/SVCD discs with PBC control or some DVD discs, the
menu display may appear on the TV screen after starting playback. In
this case, select an item which you want to play back from the menu.
Otherwise, the playback cannot go forward. Refer to “Playback
Control (PBC) Function” (墌 pg. 29) or “Locating A Desired Scene
Using The DVD Menu” (墌 pg. 26).
● The Library Database Navigation also enables you to search and
select the desired titles. (墌 pg. 50)
4 Press 9 to pause playback.
● To resume normal playback, press 4.
5 Press 8 to stop playback.
● When a recordable disc is played, playback stops and a programme
received with the unit’s tuner resumes on the TV screen.
● When a playback-only disc is played, playback stops and the still
image at the time you press 8 remains on the TV screen. Pressing 8
again resumes a programme received with the unit’s tuner.
● If x is pressed during playback, playback stops, then the disc tray
opens.
ENTER
NOTES:
4
SELECT
8
9
● When the Library Database Navigation screen appears, choose a
thumbnail image of the desired title on the TV screen, then press
SELECT(4) or ENTER. (墌 pg. 50)
● It is not possible to playback the DVD disc recorded in 96 kHz on
DVD during recording or Live Memory Playback on HDD.
ATTENTION:
● It takes approximately 30 seconds to read a disc depending on the
type and condition of the disc since this unit is multi-disc
compatible (DVD-RAM, DVD-RW, DVD-R). It may even take
several minutes when a disc is dirty, scratched or warped.
● It may take a few seconds to start playback. This is not a
malfunction.
● Forward/reverse high-speed search and other operations cannot
be performed while playback is stopped.
Page 25
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Left+
DR-MH30EU_05DVD Operation.fm Page 26 Wednesday, June 30, 2004 5:14 PM
26
EN
BASIC OPERATIONS ON DVD DECK
Locating The Start Point Of The Item Or Skip The Item
Playback Features
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
CABLE/SAT
TV
DVD
Press 2 or 6 during playback.
● Pressing 6 locates the start point of the item or skips the item for
forward direction, then resumes playback.
● Pressing 2 locates the start point of the item or skips the item for
reverse direction, then resumes playback.
When a DVD-RAM/RW/R disc is played
x
Current programme
DVD
0-9
MARK
News
TOP MENU
ENTER
rtwe
MENU
2
4
3/SLOW 8
Previous
programme
Drama
Next
programme
Reverse
Movie
Forward
●: marked points (墌 pg. 27)
6
5/SLOW +
9
Example:
To locate the beginning of the next item, press 6 once.
To locate the beginning of the current item, press 2 once.
To locate the beginning of the previous item, press 2 three
times.
When a DVD VIDEO, Audio CD or Video CD/SVCD disc is
played
Playback point
Locating A Desired Scene Using The DVD Menu
DVD VIDEO/finalised DVD-R/-RW (Video mode) discs may have
top menu and disc menu.
Top menu
DVD discs generally have their own menus which show the disc
contents. These menus contain various items such as titles of a
movie, names of songs, or artist information. You can locate a
desired scene by using the top menu displayed on the TV screen.
Press TOP MENU to access the top menu.
Disc menu
Disc menus include playback data (angle menu, subtitle menu,
etc.) specific to each title.
Press MENU to access the disc menu.
Scene 2
(Chapter 2)
or
Track 2
Reverse
Scene 3
(Chapter 3)
or
Track 3
Scene 4
(Chapter 4)
or
Track 4
Forward
Example:
To locate the beginning of the next item, press 6 once.
To locate the beginning of the current item, press 2 once.
High-Speed Search
1 Press TOP MENU or MENU to
access the DVD menu.
2 Press rt w e to select a
desired title, then press ENTER.
Playback starts.
● It may be possible to select the
desired item using the number
keys depending on the menu
display.
During playback, press 5 for forward high-speed search, or 3
for reverse high-speed search.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press 4.
Example:
NOTE:
When “X” appears on the TV screen
in step 1, the disc does not have a top menu or disc menu.
Page 26
For Audio CD
You can perform 4 levels of speed search with 5 and 3.
(Audio is active also during high-speed search.) You cannot
perform slow motion for each direction.
Wednesday, 30 June 2004 17:14
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 27 Tuesday, June 29, 2004 5:41 PM
BASIC OPERATIONS ON DVD DECK
Still Picture/Frame-By-Frame Playback
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5) to activate frame-byframe playback.
● Each press of SLOW – (3) or SLOW + (5) advances/reverses
the still picture frame by frame.
● Frame-by-frame playback for reverse direction cannot be performed
with Video CD/SVCD discs.
● To resume normal playback, press 4.
Slow Motion
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5) for 2 or more seconds.
● Each press of SLOW – (3) or SLOW + (5) increases the slow
motion speed for each direction (from 1/16 to 1/2 times the normal
speed).
● Slow motion for reverse direction cannot be performed with Video
CD/SVCD discs.
Skip Search
During playback, press
.
● Each press initiates an approximately 30-second period of fastmotion playback. Normal playback resumes automatically.
Resume Function
It is possible to memorize the position where you stop playback
and resume playback from that position.
● Be sure to set “RESUME” to “ON” or “DISC RESUME”. (墌 pg. 68)
1 Press 8 during playback to memorize a resume point.
● The unit enters Resume Stop mode and memorizes the position
where you have stopped playback as a resume point. (The inside of
the disc status indicator on the front display panel blinks while
memorising.)
● The unit retains a memory of the resume points of the last 30 discs
played back, even though they have been ejected if “RESUME” is set
to “DISC RESUME”. (墌 pg. 68)
● To clear the resume points:
(The inside of the disc status indicator stops blinking and lights.)
When “RESUME” is set to “ON”:
EN
27
NOTES:
● “DISC RESUME” setting works on DVD VIDEO, VCD, SVCD and
already finalised DVD-R/DVD-RW (video mode) discs. For other
types of discs, the function under “ON” setting will be applied even if
“RESUME” is set to “DISC RESUME”. (墌 pg. 68)
● If you stop the playback of a disc for which a resume point has
already been memorized, the memory will be updated with the new
resume point.
● After the unit has memorized the resume points for 30 discs,
remembering a new resume point will cause the unit to delete the
oldest memorized point. Stopping playback of a disc for which a
resume point is already stored may change the order in which the
points are stored. This may potentially change the order in which
points are deleted.
● When the unit memorizes a resume point for a disc, it also
remembers audio language, subtitle and angle settings.
● This function may not work for some Video CD/SVCDs.
● When “RESUME” is changed to “ON” or “OFF” (墌 pg. 68), resume
points of the discs memorized with “RESUME” set to “DISC
RESUME” will be cleared.
● Resume points are memorized for each side of a double-sided disc.
Marking Positions To Play Back Again Later
It is possible to mark positions (up to 999 points) where you want to
play back once again later, and start playback from a marked
position. Marking onto DVD-RAM/RW/R discs when recording is
helpful to locate a start point when you play back the discs later.
To mark positions:
During playback, press MARK at
positions you want to mark.
● “MARK” appears on the TV screen.
You can easily locate the marked
positions using 2 or 6 when you
play back the disc.
To delete the marked positions:
While paused, press 2 or 6 to
locate a marked position you want to
delete, then press MARK.
● Crossed “MARK” appears on the TV
screen, and the marked position is
deleted.
NOTES:
● When a monaural programme changes to a stereo programme while
recording, a mark signal is automatically recorded.
● When a DVD-R/RW (Video mode) disc is finalised, marked points
marked before finalising will be deleted, and programmes will be
divided automatically into “chapters” approximately every 5 minutes.
(墌 pg. 75)
•
•
•
•
Press 1 to turn off the unit.
Press x to take out the disc.
Press 8 in stop mode.
Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
When “RESUME” is set to “DISC RESUME”:
• Set “RESUME” to “OFF”. (墌 pg. 68)
• Press 8 in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
2 Press 4 in stop mode to resume playback. The unit starts
playback from the resume point.
Page 27
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 28 Tuesday, June 29, 2004 5:41 PM
28
EN
BASIC OPERATIONS ON DVD DECK
CABLE/SAT
TV
Angle Selection
DVD
DVD
You can enjoy a variety of scene angles if a DVD VIDEO disc
contains “multi-angle” parts, where the same scene was shot from
different angles.
If the disc contains “multi-angle” parts, “
” appears on the TV
screen at the beginning of the “multi-angle” part.
0-9
TOP MENU
ENTER
rtwe
MENU
PREVIOUS
RETURN
NEXT
4
8
DISPLAY
SET UP
AUDIO
SUBTITLE
ANGLE
1 Press ANGLE during playback.
The angle selection display
appears on the TV screen.
2 Press ANGLE or w e to select
When 3 scene angles are
contained.
your desired angle.
● Each time you press ANGLE or
w e, the angle changes.
● When “X” appears on the TV screen, the current scene is not
recorded from multiple angles. In addition, some discs prohibit angle
selection.
● To clear the angle selection display, press ENTER. In addition, the
angle selection display disappears automatically if no operation is
done for 10 seconds.
Subtitle Selection
Checking The Time Information
You can check time information of a disc on the front display panel
and the TV screen.
Each press of DISPLAY changes the display as follows:
8 DVD-RAM/DVD-R/DVD-RW
During recording
Clock time (front display panel only) ] Current title elapsed time
] Disc remaining time* ] (back to the beginning)
* only discs before finalising
● Clock time is displayed only when a recordable disc is played back.
During playback
Each title elapsed time ] Current title elapsed time ]
Disc remaining time* ] (back to the beginning)
* only discs before finalising
In stop mode or during playback
● In FR mode, it is possible to set recording time in detail using w e.
(墌 pg. 37)
● It is not possible to switch the recording mode during playback or
while recording.
Some DVD VIDEO discs contain more than one subtitle language,
from among which you can choose the desired subtitle language.
“ ” appears on the TV screen at the beginning of the part where
more than one subtitle language are recorded.
1 Press SUBTITLE during
playback. The subtitle selection
display appears on the TV screen.
● Each time you press SUBTITLE,
the subtitle display is switched on
and off.
ENGLISH
When 3 subtitle languages are
contained.
2 Press w e to select your desired language.
● To clear the subtitle selection display, press ENTER.
NOTES:
● When “X” appears on the TV screen, no subtitle language is
recorded.
● When the subtitle language won’t be changed with the procedure
above, change the subtitle on a disc menu displayed by pressing
MENU.
8 DVD VIDEO/Video CD/SVCD/Audio CD
During playback
Current track elapsed time ] Current track remaining time ] Total
elapsed time ] Total remaining time ] (back to the beginning)
In stop mode
0:00 ] Playback time of track 1 ] 0:00 ] Total length of a disc ]
(back to the beginning)
NOTE:
When a PBC-compatible Video CD/SVCD disc is loaded, deactivate the
PBC function. (墌 pg. 29)
Page 28
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 29 Tuesday, June 29, 2004 5:41 PM
BASIC OPERATIONS ON DVD DECK
Audio Language/Sound Selection
EN
29
● Each time you press AUDIO or w e, the audio language/sound
changes.
● To clear the Audio Language/Sound selection display, press ENTER.
When you can’t switch the audio channel of a bilingual
programme
When the unit is connected with a digital audio device using an
optional optical cable and “DIGITAL AUDIO OUT” is set to “DOLBY
DIGITAL/PCM”, it is not possible to switch the audio channel of a
bilingual programme recorded on a DVD-RAM or DVD-RW (VR
mode) disc. (墌 pg. 66) In this case, perform the following steps
using the remote control to switch “DIGITAL AUDIO OUT” from
“DOLBY DIGITAL/PCM” to “PCM ONLY”.
A Press SET UP to access the Main Menu screen.
B Press w e to select “DVD VIDEO SET UP”, then press t.
C Press w e to select “AUDIO OUTPUT”, then press t.
D Press rt to select “DIGITAL AUDIO OUT”, then press
ENTER.
E Press rt to select “PCM ONLY”, then press ENTER.
(墌 pg. 67)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel.
NOTES:
Playback Control (PBC) Function
Audio Channel Selection
Some Video CD/SVCD discs support the PBC function. PBC is an
abbreviation of “Play Back Control”. A Video CD/SVCD disc
recorded with PBC has its own menus, such as a list of the songs
on the disc. You can locate a specific scene by using the menu.
Some DVD VIDEO discs contain the multiple audio language or
sound. You can select the desired audio language or sound. For
some Video CD/SVCD discs, you can switch the audio channel to
choose Karaoke either with or without the vocal.
1 Press AUDIO during playback.
The Audio Language/Sound
selection display appears.
2 Press AUDIO or w e to select
When 3 audio languages are
contained.
your desired audio language/
sound.
● When “X” appears on the TV screen, no audio language is recorded.
● When the audio language won’t be changed with the procedure
above, change the audio on a disc menu displayed by pressing
MENU.
● It is only possible to select the audio language in stop mode. The
audio language cannot be selected during playback.
1 Press 4 in stop mode. The PBC menu appears.
2 Press the number keys to enter the number of the desired
When watching bilingual programmes or playing discs on which
you recorded bilingual or stereo programmes, you can choose the
desired audio channel.
● When “SUPERIMPOSE” is set to “AUTO”, you can confirm on the TV
screen the audio channel you have chosen. (墌 pg. 69)
● Each time you press AUDIO, the audio channel
changes.
TRACK
USE
On-Screen Display
For main and sub audio of bilingual
programme
For main audio of bilingual programme
For sub audio of bilingual programme
For stereo discs
scene. The unit starts playback of the selected item.
● “PBC” appears on the front display panel.
● When “NEXT” or “PREVIOUS” appears on the TV screen:
Pressing NEXT (6) advances to the next page.
Pressing PREVIOUS (2) returns to the previous page.
● You can return to the menu by pressing RETURN.
● The method of the operation is different depending on the disc.
NOTES:
● If you want to playback a PBC-compatible Video CD/SVCD disc
without activating the PBC function, start playback in stop mode by
using the number keys, instead of the 4 button, to choose the track,
then press ENTER.
● To activate the PBC function when a PBC-compatible Video CD/
SVCD disc is being played back without the PBC function, press TOP
MENU, or press 8 then press 4.
To Move Back The Playback Position Slightly
(One Touch Replay Function)
For audio of left channel
For audio of right channel
NOTE:
It is not possible for DVD-R/DVD-RW (Video mode) disc playback to
switch the audio channel. The audio channel is played back as set in
“VIDEO MODE RECORDING AUDIO” setting. (墌 pg. 68)
Page 29
You can move back the playback position slightly.
1 Press
.
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds and
resumes pause.
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 30 Tuesday, June 29, 2004 5:41 PM
30
EN
BASIC OPERATIONS ON DVD DECK
Using The On-screen Bar
The on-screen bar allows you to control various playback
functions. Some of the functions operated on Navigation Menu can
be controlled on the On-screen bar.
ATTENTION:
The on-screen bar can also be used for the HDD deck.
Be sure to clear Library Database Navigation screen by pressing
NAVIGATION.
A
B
C
D
E
F
G
H
I
J
K
L
Disc type.
Select this for Repeat Playback. (墌 pg. 31)
Select this for A-B Repeat Playback. (墌 pg. 31)
Select this for search function. (墌 pg. 31)
Select this for time search function. (墌 pg. 32)
Select this to switch Simulated Surround Effect function.
(墌 pg. 32)
Select this for Picture Control function. (墌 pg. 32)
Select this to switch picture source type. (墌 pg. 33)
Current status area for the selected item.
Select this for Programme Playback. (墌 pg. 33)
Select this for Random Playback. (墌 pg. 33)
Select this to control the switching interval of the slide show.
(墌 pg. 33)
NOTE:
CABLE/SAT
TV
Although examples of the on-screen bar are provided here only for 3
types of discs, the on-screen bar will be displayed for whichever disc
indicated in the left column.
DVD
Basic Operation On The On-screen Bar
Example: When selecting Picture Control function of DVD
During playback or while stopped
CANCEL
1 Press ON SCREEN twice to access the on-screen bar. The item
currently selected is highlighted and pointed by H.
NAVIGATION
ENTER
TITLE 99
rtwe
TRACK 99
EACH 0:00
3D-ON
DVD-
CINEMA AUTO 1
VIDEO
2 Press w e to select “
”, then press ENTER. The pop-up
window appears under the selected item.
CLEAR
ON SCREEN
TITLE 99
TRACK 99
EACH 0:00
3D-ON
DVD-
CINEMA AUTO 1
VIDEO
3 Press rt to select the desired option, then press ENTER.
TITLE 99
How To Access The On-screen Bar
TRACK 99
DVD-
1 Press ON SCREEN twice whenever a disc is loaded.
3D-ON
CINEMA AUTO 1
VIDEO
NORMAL
Contents of the on-screen bar during playback
CINEMA
DVD VIDEO
TITLE 99
EACH 0:00
SHARP
TRACK 99
SOFT
EACH 0:00
3D-ON
DVD-
CINEMA AUTO 1
VIDEO
To clear the on-screen bar
Press ON SCREEN.
NOTE:
See the corresponding pages for details on each menu item.
Video CD/SVCD
TRACK 99
EACH 0:00
CINEMA
VCD
JPEG disc
GROUP 99
TRACK 99
EACH 179:59
5 SEC.
R
Page 30
CINEMA
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 31 Tuesday, June 29, 2004 5:41 PM
BASIC OPERATIONS ON DVD DECK
Repeat Playback
EN
31
To clear the on-screen bar
Press ON SCREEN.
To cancel A-B Repeat Playback
Press w e to select “
”, then press ENTER.
You can repeat playback as you like according to the type of disc.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
TRACK 99
EACH 0:00
3D-ON
DVD-
CINEMA AUTO 1
VIDEO
3 Press rt repeatedly to select the desired Repeat mode, then
press ENTER.
DVD-RAM/RW/R
OFF: Repeat playback is not performed.
ALL REPEAT: The whole disc is played back repeatedly.
TITLE REPEAT: The current title is played back repeatedly.
DVD VIDEO
OFF: Repeat playback is not performed.
TITLE REPEAT: The current title is played back repeatedly.
CHAPTER REPEAT: The current chapter is played back repeatedly.
Audio CD/Video CD/SVCD/JPEG/MP3
OFF: Repeat playback is not performed.
ALL REPEAT: The whole disc is played back repeatedly.
GROUP REPEAT*: The current group is played back repeatedly.
TRACK REPEAT*: The current track is played back repeatedly.
* “GROUP REPEAT” cannot be selected for Audio CD and Video CD/SVCD
discs.
* “TRACK REPEAT” cannot be selected for JPEG discs.
NOTES:
● A-B Repeat Playback may not work properly depending on the type
of disc being used.
● The subtitles recorded around the A-B point may not appear.
● When the end of the item is reached before the end point is set, the
on-screen bar disappears from the TV screen. In such a case, repeat
the procedure from step 1.
● The point B must be set at least 3 seconds after the point A.
● When playing back a DVD, A-B Repeat Playback is possible only
within the same title.
●“
” cannot be selected during Programme and Random
Playback.
●“
” cannot be selected while stopped.
Locating The Beginning Of A Desired Selection
You can locate the beginning of a title, chapter, group or track.
During playback or while stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER.
3 Press rt to select the desired item, then press ENTER.
● Skip this step for Video CD/SVCD and Audio CD.
For DVD-RAM/RW/R, DVD VIDEO
“TITLE SEARCH” or “CHAPTER SEARCH” is selectable. (“TITLE
SEARCH” only is selectable while stopped.)
To clear the on-screen bar
Press ON SCREEN.
For JPEG, MP3
“GROUP SEARCH” or “TRACK SEARCH” is selectable.
To cancel Repeat Playback
Repeat the above procedure from step 1, select “OFF” in step 3,
then press ENTER.
For Video CD/SVCD, Audio CD
“TRACK” is selectable.
NOTES:
● Repeat Playback is not possible for a Video CD/SVCD with PBC
function.
● Repeat Playback may not work properly depending on the type of the
disc being used.
GROUP 99
TRACK 99
DVD-
EACH 179:59
5
CINEMA
VIDEO
TITLE SEARCH
CHAPTER SEARCH
4 Press the number keys to enter the desired item number, then
A-B Repeat Playback
press ENTER.
● Playback starts from the selected section.
Examples:
A To select track 5, press the number key “5”.
B To select track 15, press the number key “1” and “5”.
C To select track 25, press the number key “2”, then “5”.
You can repeat the desired part.
During playback
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”.
3 Press ENTER at the beginning of the desired part you want to
repeat (point A). The elapsed playing time of the point A appears.
TITLE 99
TRACK 99
EACH 0:00
3D-ON
DVD-
1 : 25 : 58
B
:
To clear the on-screen bar
Press ON SCREEN.
NOTES:
CINEMA AUTO 1
VIDEO
A
If you have specified a wrong selection
Press CANCEL (&) or CLEAR (8) to clear the wrong number,
then enter the correct one before you press ENTER in this step.
:
4 Press ENTER at the end of the desired part you want to repeat
(point B). The elapsed playing time of the point B appears.
● When “X” is displayed on the TV screen in step 4, the chapter you
have selected is not contained in the disc, or chapter search does not
work on the disc.
● Before you press ENTER, playback may start automatically when you
enter the section’s number depending on the disc.
● This function is not possible for a Video CD/SVCD with PBC function.
● The selected part of the disc (between point A and B) is played
repeatedly.
TITLE 99
TRACK 99
EACH 0:00
3D-ON
DVD-
CINEMA AUTO 1
VIDEO
A
Page 31
1 : 25 : 58
B
1 : 40 : 00
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 32 Tuesday, June 29, 2004 5:41 PM
32
EN
BASIC OPERATIONS ON DVD DECK
CABLE/SAT
TV
Simulated Surround Effect
DVD
It is possible to get a simulated surround effect from your stereo
system. You can enjoy the virtual surround sound with your
2-channel stereo system.
0-9
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”, then press ENTER.
CANCEL
● Above the selected item, “3D-ON” appears and Simulated Surround
Effect is activated.
● Each time you press ENTER, “3D-ON” appears and disappears
alternately.
ENTER
rtwe
6
2
TITLE 99
4
CLEAR
TRACK 99
EACH 0:00
3D-ON
DVD-
CINEMA AUTO 1
VIDEO
ON SCREEN
To clear the on-screen bar
Press ON SCREEN.
To cancel the simulated surround effect
Press ENTER to clear “3D-ON” from the screen.
NOTES:
Time Search
You can play back a disc from the desired point by specifying the
elapsed playing time from the beginning of a programme (DVD-RAM,
DVD-R, DVD-RW, DVD VIDEO and HDD) or a disc (Video CD/SVCD
and Audio CD).
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
TRACK 99
EACH 0:00
CINEMA AUTO 1
DVDVIDEO
● Simulated Surround Effect works correctly only when playing back a
title recorded in multichannels.
● Simulated Surround Effect does not affect the DVD VIDEO bitstream
signal from the DIGITAL OUT connectors.
● When Simulated Surround Effect is activated, the settings of
“ANALOG AUDIO OUT” and “D. RANGE CONTROL” are disabled.
(墌 pg. 67)
Adjusting The Picture Quality
You can obtain optimal picture quality by selecting an appropriate
picture mode.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
3 Press the number keys to enter the time, then press ENTER.
Playback starts from the specified time.
Example:
To play back from a point 12 (minutes): 50 (seconds) elapsed.
TITLE 99
TRACK 99
DVD-
EACH 0:00
CINEMA AUTO 1
VIDEO
3 Press rt to select the desired option, then press ENTER.
Press 1
Press 2
NORMAL: Normally select this option.
CINEMA: Suitable for a movie disc, etc.
SHARP: Clearer, sharper-edged picture when viewing images with
Press 5
Press 0
SOFT: Select this option when too much noise appears.
lots of flat, same-coloured surfaces such as cartoons.
To clear the on-screen bar
Press ON SCREEN.
If you have specified a wrong selection,
Press CANCEL (&) (for the last entered number) or CLEAR (8)
(for whole numbers) to clear the wrong number, then enter the
correct one(s) before you press ENTER in this step.
To clear the on-screen bar
Press ON SCREEN.
NOTES:
● When “X” is displayed on the TV screen in step 3, you have selected
a point that excesses the recording time of the disc.
● Some DVD VIDEO discs do not contain time information, and it is not
possible to use the Time Search function. In such cases, “X” is
displayed on the TV screen as well.
● This function is not possible for a Video CD/SVCD with PBC function.
Page 32
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 33 Tuesday, June 29, 2004 5:41 PM
BASIC OPERATIONS ON DVD DECK
You can obtain optimal picture quality by selecting whether the
content on the disc is processed by field (video source) or by frame
(film source).
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
TRACK 99
EACH 0:00
3D-ON
DVD-
33
4 Press 4. Playback starts in the programmed order.
Setting The Progressive Mode
TITLE 99
EN
CINEMA AUTO 1
● When all of the programmed tracks have been played back,
Programme Playback stops, but the programmed information
remains.
● To add tracks to the end of the programme, perform steps 1 through
3.
● During Programme Playback, pressing 6 skips to the next
selection of the programme. Pressing 2 returns to the beginning of
the current selection.
To clear the on-screen bar and the contents of the programme
Press ON SCREEN.
To cancel Programme Playback
Press w e to select “PRGM”, then press ENTER.
NOTE:
Programme Playback is not possible depending on the type of disc.
VIDEO
3 Press rt to select the desired option, then press ENTER.
Random Playback
AUTO 1: Used to play a disc containing both video and film source
materials. This system recognizes the source type (video or film)
of the current disc according to the disc information. Normally
select this option.
AUTO 2: Almost the same as the “AUTO 1”, but the processing of
the scenes with movement is different. Select “AUTO 1” or
“AUTO 2” to your preference.
FILM: Suitable for playing back a progressive scanned film source
disc.
VIDEO: Suitable for playing back a video source disc. The outlines
on the played back pictures will be soft.
To clear the on-screen bar
Press ON SCREEN.
You can play back all the tracks on the disc in random order.
While stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “RND”, then press ENTER. Playback starts
in random order.
TRACK 99
EACH 0:00
CINEMA
VCD
NOTE:
When the progressive mode is set, be sure to set “L-1 OUTPUT” to
“COMPONENT”. (墌 pg. 61) Progressive scan is output only from
COMPONENT VIDEO OUT connector.
Programme Playback
To clear the on-screen bar
Press ON SCREEN.
To cancel Random Playback
Perform steps 1 and 2.
NOTE:
The same track will not be played back more than once during Random
Playback.
You can programme up to 30 tracks (Video CD/SVCD or Audio CD)
to play back in the desired order.
Select The Switching Interval Of The Slide Show
While stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “PRGM”, then press ENTER. The
You can control the switching interval of the slide show.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER. The pop-up
programme table appears under on-screen bar.
TRACK 99
window appears under the selected item.
EACH 0:00
CINEMA
GROUP 99
TRACK 99
VCD
3 Press the number keys to
EACH 179:59
5 SEC.
CINEMA
R
enter the track numbers in the
desired order.
3 Press rt to select the desired option, then press ENTER.
Examples:
A To select track 5, press the
number key “5” and ENTER.
B To select track 15, press the
number key “1” and “5”.
C To select track 25, press the number key “2” and “5”.
To clear the on-screen bar
Press ON SCREEN.
● Each time you press rt, the interval changes as follows:
5 SEC. { 10 SEC. { 15 SEC. { 20 SEC. { 25 SEC. {
30 SEC. { (Back to the beginning)
If you have specified a wrong selection
Press CANCEL (&). The last selection is erased.
Or press CLEAR (8). The whole selection is erased.
Page 33
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 34 Tuesday, June 29, 2004 5:41 PM
34
EN
BASIC OPERATIONS ON DVD DECK
9 Press the number keys to enter the same password as in
Parental Lock
step 6 above, then press ENTER.
10 Press SET UP to complete the setting.
NOTE:
Remember your password, or make a note of it.
This function restricts playback of DVD VIDEO discs which contain
violent (and other) scenes according to the level set by the user.
For example, if a movie which includes violent scenes supports the
parental lock feature, such scenes which you do not want to let
children view can be cut or replaced by other scenes.
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
To Change The Settings
You can change the Parental Lock settings later.
1 Perform steps 1 to 3 of “To Set Parental Lock For The First
Time” to access the “PARENTAL LOCK” screen before continuing.
To change the level
2 Press rt to select “PARENTAL LEVEL”, then press ENTER.
3 Press rt to select the desired level, then press ENTER.
To change the country code
CABLE/SAT
TV
4 Press rt to select “COUNTRY CODE”, then press ENTER.
5 Press rt to select your country code, then press ENTER.
DVD
● See “Country/Area Code List for Parental Lock” (墌 pg. 83).
DVD
6 Press the number keys to enter the same password as in
step 6 of “To Set Parental Lock For The First Time”, then press
ENTER.
0-9
7 Press SET UP twice to complete the setting.
NOTE:
If you forget your password, enter “8888” in step 6.
ENTER
To Temporarily Release Parental Lock
rtwe
When you set the Parental Lock level strictly, some discs may not
be played back at all. When you insert such a disc and try to play it
back, the confirmation screen appears on the TV screen, asking
you whether you want Parental Lock to be temporarily released or
not.
1 Load a disc.
● If the disc is rated higher than the selected level, the confirmation
screen appears.
SET UP
2 Press w e to select “YES”, then press ENTER.
● If you select “NO”, you cannot play back that disc.
3 Press the number keys to enter the same password as in
step 6 of “To Set Parental Lock For The First Time”, then press
ENTER.
To Set Parental Lock For The First Time
While stopped
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “DVD VIDEO SET UP”, then press t.
3 Press w e to select
DVD VIDEO SET UP HDD/DVD SET UP
“PARENTAL LOCK”, then
press t.
LANGUAGE SET
AUDIO OUTPUT
FUNCTION SET UP
INITIAL SET UP
PARENTAL LOCK
DISC PLAY SET UP
PARENTAL LEVEL
NONE
COUNTRY CODE
● When you enter the correct password, the Parental Lock is released
and the unit starts playback.
● If you enter a wrong password, “ENTRY ERROR” appears on the TV
screen. Enter the correct password.
● If you have successively entered wrong password three times,
“ENTRY ERROR CAN NOT CHANGE PASSWORD” appears on the
TV screen. In such a case, press ENTER. The disc will stop. Then
play back the disc again, and try the procedure again from step 1.
NOTE:
US
If you forget your password, enter “8888” in step 3.
4 Press rt to select
“PARENTAL LEVEL”, then press
ENTER.
5 Press rt to select the desired
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
DVD VIDEO SET UP HDD/DVD SET UP
LANGUAGE SET
AUDIO OUTPUT
PARENTAL LEVEL
FUNCTION SET UP
INITIAL SET UP
PARENTAL LOCK
DISC PLAY SET UP
NONE
COUNTRY CODE
US
level, then press ENTER.
● The smaller the value of level is,
the more restrictive the Parental
Lock level becomes.
● Select “NONE” to cancel the
restriction.
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
6 Press the number keys to enter your desired four-digit number,
then press ENTER.
● If you made a mistake, enter a correct number again.
7 Press rt to select “COUNTRY CODE”, then press ENTER.
8 Press rt to select your country code, then press ENTER.
● If you do not need to change your country code, jump to 10.
● See “Country/Area Code List for Parental Lock” (墌 pg. 83).
Page 34
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 35 Tuesday, June 29, 2004 5:41 PM
BASIC OPERATIONS ON DVD DECK
35
NOTES:
Basic Recording
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
ATTENTION:
It is not possible to record programmes on a DVD-R disc which
has already been finalised.
4
8
7
9
DVD
DVD Lamp
CABLE/SAT
TV
● It is recommended to format a DVD-RAM disc before use if you use
the disc on this unit for the first time.
● When using a brand-new DVD-RW disc, format the disc either in VR
mode or in Video mode. (墌 pg. 74)
● Recordings made on DVD-R/RW disc must be finalised to play back
on other DVD players. Perform “Finalise A Disc (DVD Deck Only)”
(墌 pg. 75).
● You can record up to 99 programmes and 999 play lists on each disc.
● Some programmes can only be recorded one time.
● When recording is started, an index of the first part of recording is
automatically recorded. (墌 pg. 49) To record satellite programmes,
refer to page 48. To delete the index, refer to page 51.
● Recording sometimes may stop or cannot be performed even if there
is enough available capacity remaining on the disc.
● It is not possible to record both on DVD and on HDD simultaneously.
Recording Mode
MPEG2 format is used as recording format. As a guide for picture
quality, the “bps” unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programmes where quick movement occurs,
such as sports programmes, and LP or EP for talk shows, etc. with
relatively less movement.
The recording modes for a 4.7 GB disc are set as follows:
DVD
DVD
Recording
mode
XP
0-9
PR+/-
Recording amount
(approx.)
10 Mbps
5 Mbps
2 hours
2 Mbps
4 hours
EP
1.6 Mbps
6 hours
1 – 6 hours
The amount varies
depending on the
selected time.
FR480
9
1 hour
LP
FR420
4
Maximum recording
time (approx.)
SP
FR60–FR360
(墌 pg. 37)
ENTER
7
8
REC MODE
EN
7 hours
8 hours
● For details on FR mode, refer to “Free Rate Function” (墌 pg. 37).
Recording Resume Function
If there is a power outage during recording, Instant Timer
Recording (ITR) (墌 pg. 36) or timer recording (墌 pg. 44, 46), the
recording will resume automatically when power is restored to the
unit unless the unit’s memory backup has expired.
1 Load a recordable disc.
● For details, refer to “Placing A Disc” (墌 pg. 8).
2 Press DVD so that the DVD lamp lights up on the unit.
3 Press PR +/– or the number keys to select the channel you
wish to record.
4 Press REC MODE repeatedly to select the recording mode,
then press ENTER.
● Each time you press REC MODE, the recording mode changes as
follows:
XP ] SP ] LP ] EP ] FR60–FR360* ] FR420, FR480]
(Back to the beginning)
* The value is selectable from 1 to 6 hours in 5-min. increment by
pressing w e repeatedly after selecting “FR60–FR360”. To change the
value in 30-min. increments, press and hold w e.
● For details on the recording mode, see the right column.
5 Press 7 on the unit to start recording. Or press and hold 7 and
press 4 on the remote control.
6 Press 7 and 9 simultaneously to pause recording.
● To resume recording, press 7 and 4 simultaneously.
7 Press 8 twice to stop recording.
● It takes about 10 seconds to end the writing session when you stop
recording.
Page 35
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 36 Tuesday, June 29, 2004 5:41 PM
36
EN
BASIC OPERATIONS ON DVD DECK
Instant Timer Recording (ITR)
Recording Features
●
●
●
●
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the unit off after
recording is finished.
1 Press 7 on the unit to start recording.
2 Press 7 again to engage the ITR mode.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
● On the front display panel, “0:30” appears.
3 If you want to record for more than 30 minutes, press 7 to
extend the time. Each press extends recording time by 30 minutes.
7
CABLE/SAT
TV AV/ VIDEO
TV
DVD
DVD
DVD
NOTES:
● You can only perform ITR using the 7 button on the unit.
● If “DIRECT REC” is set to “ON” in the menu, Instant Timer Recording
(ITR) function does not work. (墌 pg. 68)
● When the recording capacity becomes full during timer recording or
Instant Timer Recording, the unit automatically performs “Relief
Recording” (墌 pg. 46).
Watch Another Programme While Recording On The
Unit
While recording is going on, you can watch another programme on
the TV by using the TV’s tuner.
NOTE:
It is required that the remote control is set to be able to operate the TV
in advance. (墌 pg. 63)
PR+/-
1 During recording, press TV AV/VIDEO to select TV mode.
● Video mode is disengaged and the video lamp (VIDEO) on the unit is
turned off.
● The programme received on the TV’s tuner is displayed on the TV
screen.
2 Slide the TV/CABLE/SAT/DVD switch to TV.
3 Press PR +/– repeatedly to select the desired channel.
NOTE:
If a decoder is connected to the unit (墌 pg. 66), you can select a
scrambled channel as well as other normal channels.
DISPLAY
Elapsed Recording Time And Disc Remaining Time
Indication
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time ] Disc remaining time ] Clock ] (Back to
the beginning)
Page 36
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_05DVD Operation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 37 Tuesday, June 29, 2004 5:41 PM
BASIC OPERATIONS ON DVD DECK
EN
37
Free Rate Function
Receiving Stereo And Bilingual Programmes
To record the entire programme, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the programme to be recorded and either the
remaining disc space or the specified recording time (from 60
minutes to 480 minutes).
Your unit is equipped with a Sound-Multiplex decoder (A2) and a
Digital stereo sound decoder (NICAM) making reception of stereo
and bilingual broadcasts possible.
When the channel is changed, the type of broadcast being
received will be displayed on the TV screen for a few seconds.
8 To record the entire programme within the actual remaining
disc space (DVD deck only)
Select “FR (JUST)” in a recording mode selection procedure.
● Note that this function is available only for timer programming
recording (墌 pg. 44, 46) and dubbing from HDD to DVD (墌 pg. 56).
8 To record the entire programme by specifying the desired
recording time
Select “FR60–FR360”, “FR420” or “FR480” in a recording mode
selection procedure. (墌 pg. 35, 38, 44, 46)
8 To record a 25-min. long daily programme five times just on
the same DVD disc for example
Perform “ShowViewTM Timer Programming” (墌 pg. 44)
procedure. Be sure to set the recording mode to “FR125” and set
Weekly/Daily Rec Function to “MON–FRI” in step 8 to fit the total
recording time to the whole disc space.
Blank
A: 1st
B: 2nd
C: 3rd
D: 4th
E: 5th
When the same programme is recorded in SP mode instead of in
“FR125”, the 5th programme cannot be recorded.
Blank
A: 1st
B: 2nd
C: 3rd
D: 4th
E: Blank (20 min.)
Type of Broadcast Being
Received
On-screen Display
A2 Stereo
A2 Bilingual
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
NOTES:
● “SUPERIMPOSE” must be set to “AUTO”. Otherwise the on-screen
displays will not appear. (墌 pg. 69)
● If the quality of stereo sound being received is poor, the broadcast
might be received in monaural with better quality.
Selection Of The Audio Channel To Be Recorded On A
Disc
When a programme is recorded on a DVD-RAM or DVD-RW disc in
VR mode, all audio channels of the receiving programme are
recorded on the disc. When you record a programme on a DVD-R
or DVD-RW disc in video mode, select the desired audio channel
(“NICAM” or “MONO”) to be recorded on the disc. (墌 pg. 68)
NOTE:
Before playing back a programme recorded in stereo, or a bilingual
programme, refer to “Audio Channel Selection” on page 29.
NOTES:
● You can programme this unit to timer-record, regardless of the disc
remaining time. When the disc remaining time is not enough, the unit
performs “Relief Recording” (墌 pg. 46). To avoid this, make sure of
the disc remaining time before setting timer-programming.
(Example) If you programmed to timer-record for 60 minutes in SP
mode on a 120-minute disc, the disc remaining time would be 30
minutes in XP mode, 60 minutes in SP mode, 120 minutes in LP
mode, 180 minutes in EP mode, and 240 minutes in FR480 mode.
Timer-recording will not complete beyond these remaining times.
● The maximum recording time of FR (JUST) mode is the same as the
recording time of FR480 mode. When timer-programming a long
programme in FR (JUST) mode on a disc whose remaining time is
short, it is recommended checking the disc remaining time in FR480
mode to see if the remaining time is enough for the programme.
● Even if more than one programme are timer-programmed in FR
(JUST) mode, only the first one is recorded.
● In order to ensure that the recording fits on the disc, this feature may
leave a slight non-recorded section at the end of the disc.
● There may be some noise and sound disturbance at the point on the
disc where the unit switches the mode.
Page 37
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_06HDD Operation.fm]
Masterpage:Left0
DR-MH30EU_00.book Page 38 Tuesday, June 29, 2004 5:41 PM
38
EN
BASIC OPERATIONS ON HDD DECK
Pause recording on HDD deck
It is not possible to pause recording. Pressing 9 initiates Live
Memory Playback.
However, it is still possible to pause recording only when recording
the channels of external sources (“L-1”, “L-2”, “F-1”, and “DV”).
Press and hold 7, then press 9 on the remote. To resume
recording, press and hold 7, then press 4 on the remote.
No operation can be made with the buttons on the unit.
Basic Recording
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
ATTENTION:
The HDD on the unit requires approximately 20 seconds to start up
after the unit has been turned on, during which no operation can be
made.
HDD
Recording Mode
MPEG2 format is used as recording format. As a guide for picture
quality, the “bps” unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programmes where quick movement occurs,
such as sports programmes, and LP or EP for talk shows, etc. with
relatively less movement.
Recording
mode
7 HDD Lamp
8
CABLE/SAT
TV
DVD
Recording amount
(approx.)
Maximum recording
time (approx.)
XP
10 Mbps
1 hour
SP
5 Mbps
2 hours
LP
2 Mbps
4 hours
HDD
EP
1.6 Mbps
6 hours
0-9
FR60–FR360
(墌 pg. 37)
PR+/-
FR420
1 – 6 hours
The amount varies
depending on the
selected time.
FR480
7 hours
8 hours
● For details on FR mode, refer to “Free Rate Function” (墌 pg. 37).
Recording Resume Function
4
8
7
9
If there is a power outage during recording, Instant Timer
Recording (ITR) (墌 pg. 39) or timer recording (墌 pg. 44, 46), the
recording will resume automatically when power is restored to the
unit unless the unit’s memory backup has expired.
REC MODE
1 Press HDD so that the HDD lamp lights up on the unit.
2 Press PR +/– or the number keys to select the channel you
wish to record.
3 Press REC MODE repeatedly to select the recording mode,
then press ENTER.
● Each time you press REC MODE, the recording mode changes as
follows:
XP ] SP ] LP ] EP ] FR60–FR360* ] FR420, FR480]
(Back to the beginning)
* The value is selectable from 1 to 6 hours in 5-min. increment by
pressing w e repeatedly after selecting “FR60–FR360”. To change the
value in 30-min. increments, press and hold w e.
● For details on the recording mode, see the right column.
4 Press 7 on the unit to start recording. Or press and hold 7 and
press 4 on the remote control.
5 Press 8 twice to stop recording.
● Pressing 8 once displays the confirmation message to stop
recording. Press 8 again to terminate recording.
NOTES:
● Continuous recording for over 48 hours is not possible.
● It is not possible to record both on DVD and on HDD simultaneously.
Page 38
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_06HDD Operation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 39 Tuesday, June 29, 2004 5:41 PM
BASIC OPERATIONS ON HDD DECK
39
Watch Another Programme While Recording On The
Unit
Recording Features
●
●
●
●
EN
While recording is going on, you can watch another programme on
the TV by using the TV’s tuner.
NOTE:
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press HDD so that the HDD lamp lights up on the unit.
It is required that the remote control is set to be able to operate the TV
in advance. (墌 pg. 63)
HDD
1 During recording, press TV AV/VIDEO to select TV mode.
● Video mode is disengaged and the video lamp (VIDEO) on the unit is
turned off.
● The programme received on the TV’s tuner is displayed on the TV
screen.
7 HDD Lamp
2 Slide the TV/CABLE/SAT/DVD switch to TV.
3 Press PR +/– repeatedly to select the desired channel.
NOTE:
CABLE/SAT
TV AV/ VIDEO
TV
DVD
If a decoder is connected to the unit (墌 pg. 66), you can select a
scrambled channel as well as other normal channels.
Elapsed Recording Time And Disc Remaining Time
Indication
HDD
PR+/-
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time ] Disc remaining time ] Clock ] (Back to
the beginning)
Receiving Stereo And Bilingual Programmes
DISPLAY
Your unit is equipped with a Sound-Multiplex decoder (A2) and a
Digital stereo sound decoder (NICAM) making reception of stereo
and bilingual broadcasts possible.
When the channel is changed, the type of broadcast being
received will be displayed on the TV screen for a few seconds.
Type of Broadcast Being
Received
Instant Timer Recording (ITR)
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the unit off after
recording is finished.
1 Press 7 on the unit to start recording.
2 Press 7 again to engage the ITR mode.
● On the front display panel, “0:30” appears.
3 If you want to record for more than 30 minutes, press 7 to
extend the time. Each press extends recording time by 30 minutes.
NOTES:
● You can only perform ITR using the 7 button on the unit.
● If “DIRECT REC” is set to “ON” in the menu, Instant Timer Recording
(ITR) function does not work. (墌 pg. 68)
● When the recording capacity becomes full during timer recording or
Instant Timer Recording, the unit is automatically shut off.
On-screen Display
A2 Stereo
A2 Bilingual
Regular Monaural
NICAM Stereo
NICAM Bilingual
NICAM Monaural
NOTES:
● “SUPERIMPOSE” must be set to “AUTO”. Otherwise the on-screen
displays will not appear. (墌 pg. 69)
● If the quality of stereo sound being received is poor, the broadcast
might be received in monaural with better quality.
Selection Of The Audio Channel To Be Recorded On A
Disc
When a programme is recorded on a DVD-RAM or DVD-RW disc in
VR mode, all audio channels of the receiving programme are
recorded on the disc. When you record a programme on a DVD-R
or DVD-RW disc in video mode, select the desired audio channel
(“NICAM” or “MONO”) to be recorded on the disc. (墌 pg. 68)
NOTE:
Before playing back a programme recorded in stereo, or a bilingual
programme, refer to “Audio Channel Selection” on page 29.
Page 39
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_06HDD Operation.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 40 Tuesday, June 29, 2004 5:41 PM
40
EN
BASIC OPERATIONS ON HDD DECK
Basic Playback
Playback Features
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press HDD so that the HDD lamp lights up on the unit.
HDD
4
CABLE/SAT
TV
DVD
HDD
8
9
CABLE/SAT
TV
DVD
HDD
4
3/SLOW -
5/SLOW +
9
ENTER
4
SELECT
8
9
High-Speed Search
During playback, press 5 for forward high-speed search, or 3
for reverse high-speed search.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press 4.
ATTENTION:
● It may take a few seconds to start playback. This is not a
malfunction.
● Forward/reverse high-speed search and other operations cannot
be performed while playback is stopped.
1 Press HDD so that the HDD lamp lights up on the unit.
2 Press 4 to start playback.
● The Library Database Navigation also enables you to search and
select the desired programmes. (墌 pg. 50)
3 Press 9 to pause playback.
● To resume normal playback, press 4.
4 Press 8 to stop playback.
NOTE:
When the Library Database Navigation screen appears, choose a
thumbnail image of the desired title on the TV screen, then press
SELECT(4) or ENTER. (墌 pg. 50)
Still Picture/Frame-By-Frame Playback
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5) to activate frame-byframe playback.
● Each press of SLOW – (3) or SLOW + (5) advances/reverses
the still picture frame by frame.
● To resume normal playback, press 4.
Slow Motion
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5) for 2 or more seconds.
● Each press of SLOW – (3) or SLOW + (5) increases the slow
motion speed for each direction (from 1/16 to 1/2 times the normal
speed).
Skip Search
During playback, press
.
● Each press initiates an approximately 30-second period of fastmotion playback. Normal playback resumes automatically.
Page 40
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_06HDD Operation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 41 Tuesday, June 29, 2004 5:41 PM
BASIC OPERATIONS ON HDD DECK
EN
41
Recording/playback Status Display
Live Memory Playback
CABLE/SAT
●
●
●
●
TV
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press HDD so that the HDD lamp lights up on the unit.
This unit records pictures onto the hard disc, instead of video
tapes, then plays back the pictures recorded on the disc. This
makes it possible to achieve high-speed writing and read-out that
has not been possible with conventional VCRs, enabling recording
and playback simultaneously.
LIVE
NAVIGATION
Press NAVIGATION to display Library Database
Navigation menu, then choose a programme to
play back. (墌 pg. 49)
High-speed spin
Recording
(High-speed writing)
DVD
Playback
(High-speed read-out)
8
ON SCREEN
Live Memory Playback status can be checked by
pressing ON SCREEN to display the bar meter on
the superimpose display. The current status is
superimposed on the TV screen. (墌 pg. 15, “When
using Live Memory playback”)
Image figure of the hard disc
It is called “Live Memory Playback” to start playback of the
programme being recorded, with a time-lag between a recording
point and a playback point, as shown in the figure below.
NOTES:
Current playback point
(Live Memory Playback)
Current recording position
(Recording point)
Recording start point
Playback
continues
0
30 min.
Recording
continues
1 hour
Currently elapsed recording time
Not only can this unit play back a programme previously recorded
while recording or timer recording another programme, but the unit
also allows you to play back from the beginning of a programme
while continuing to record the same programme.
Temporary recording for Live Memory
This unit automatically records the channel being received, within
the specified range of time, to the reserved space on the hard disc.
The time range can be set for 30 minutes, 1 hour, and 3 hours.
(墌 pg. 68)
NOTE:
Previous temporary recordings will be overwritten since the unit is
always recording the channel being received. Thus, it is not possible to
play back TV programmes recorded beyond the specified range of time
since they are already overwritten. To avoid this in order to save titles,
perform normal recording (墌 pg. 38), timer recording (墌 pg. 44, 46),
or Live Memory Recording (墌 pg. 43).
● Live Memory Playback cannot be performed for approximately 30
seconds after recording has started.
● Although high-speed search up to approximately 30 seconds before
the current recording point is possible during Live Memory Playback,
once the current recording point is reached, the unit resumes normal
playback and maintains a delay of approximately 30 seconds so that
recording and playback can continue.
● When using Live Memory Playback during timer recording, playback
continues even after the end of the recording.
● When using Live Memory Playback during timer recording, playback
is automatically stopped just before recording starts, and then
recording starts when the time arrives for the next timer-programme.
● It is impossible to perform ITR even if you press 7 during Live
Memory Playback. (墌 pg. 39)
Press 8 to display the programme being recorded, then perform ITR
settings.
● Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
● Live Memory Playback cannot be performed while recording the
source from DV input. (墌 pg. 58, “DV Dubbing”)
● When LIVE CHECK is pressed to display the picture currently being
recorded, the picture size may not be correct.
● Press 7 or LIVE to stop Live Memory Playback.
● Live Memory Playback cannot be performed, even if the “LIVE
MEMORY” is set to other than OFF in “HDD SET UP”, because
temporary recording on HDD stops during recording on DVD.
About limitation on temporary recording
The temporary recording for Live Memory is cancelled in the
following cases, and will start all over again when it is to resume.
● When the power is turned off
● When the system is powered again after a power failure was
occurred
● When normal recording, timer recording, Live Memory Recording,
or Automatic Satellite Programme Recording (墌 pg. 48) is
performed
● When the “LIVE MEMORY” setting is changed (墌 pg. 68)
● When tuner channel setting is performed (墌 pg. 70)
● When dubbing is performed by pressing DUBBING (墌 pg. 56)
● When “DV” is selected by pressing PR +/– (墌 pg. 58)
Page 41
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_06HDD Operation.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 42 Tuesday, June 29, 2004 5:41 PM
42 EN BASIC OPERATIONS ON HDD DECK
Buttons To Be Used During Live Memory Playback
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press HDD so that the HDD lamp lights up on the unit.
CABLE/SAT
TV
DVD
A LIVE
Returns to on air programme screen. When a confirmation
message appears by pressing this button during timer
programming or title editing, etc., follow the instruction to return to
the previous screen.
B NAVIGATION
Displays Library Database Navigation menu. You can choose a title
to play back.
C3
● Each press of the button during playback advances the playback
speed in 5 steps for reverse direction.
HDD
Available only when paused
● Each press of the button reverses the still picture frame by frame.
● Pressing down for 2 or more seconds reverses playback at 1/16 times
the normal speed. Then, each press of the button reverses slowmotion at 1/16 times, 1/4 times and 1/2 times the normal playback.
A
B
D5
● Each press of the button during playback advances the playback
speed in 4 steps for forward direction.
Available only when paused
C
E
G
H
D
F
I
J
K
● Each press of the button advances the still picture frame by frame.
● Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed. Then, each press of the button advances
slow-motion at 1/16 times, 1/4 times and 1/2 times the normal
playback.
E8
● Pressing once during Live Memory Playback or Live Memory
Recording returns to the screen on air.
● Pressing twice during recording stops recording and returns to the
screen on air.
F9
Pressing once pauses playback (still picture playback). Pressing
repeatedly advances the still picture frame by frame.
G JUMP –
Each press of the button during playback or Live Memory Playback
jumps back for the selected time interval and resumes playback.
(墌 pg. 43, “Jump Search”)
H JUMP +
Each press of the button during playback or Live Memory Playback
jumps forward for the selected time interval and resumes playback.
(墌 pg. 43, “Jump Search”)
I
Pressing once skips forward for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips forward continuously as many times as
pressed.
It is useful when skipping over unwanted sections.
J
Pressing once skips back for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips back for approximately 7 seconds
continuously as many times as pressed.
It is useful when watching sports programmes, etc.
K LIVE CHECK
Pressing once displays the picture currently being recorded and
the one being played back simultaneously.
Pressing successively clears the Live Check window and displays
only the picture currently being played back.
You can check, for example, if the programme you are recording
has already finished.
Page 42
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_06HDD Operation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 43 Tuesday, June 29, 2004 5:41 PM
BASIC OPERATIONS ON HDD DECK
To Play Back The Previous Part Of The Channel
Currently Recording or Watching
You can play back the previous part of the channel you are
recording or watching (temporarily recorded on the background)
from the desired point. (墌 pg. 41, “Temporary recording for Live
Memory”)
1 Press 2 or 3 to locate the point to start playback from.
● Each press of 3 increases the reverse search speed.
2 Press 4 to start Live Memory Playback.
3 Press 8 to stop Live Memory Playback.
● The on-air screen resumes.
NOTES:
● You can use various playback features during Live Memory Playback.
(墌 pg. 40)
● If you have started actual recording by pressing 7, pressing 8 in
step 3 only resumes the on-air screen. To stop actual recording,
press 8 again.
To Record From The Previous Part Of The Channel
Currently Watching (Live Memory Recording)
You can start recording from the previous part of the channel you
are currently watching (temporarily recorded on the background).
(墌 pg. 41, “Temporary recording for Live Memory”)
1 Press 2 or 3 to locate the point to start recording from.
● Each press of 3 increases the reverse search speed.
2 Press 7 on the unit to start Live Memory Recording. Or press
and hold 7 and press 4 on the remote control.
3 Press 8 to stop Live Memory Recording.
● The on-air screen resumes.
NOTES:
To Move Back The Playback Position Slightly While
Recording (One Touch Replay Function)
You can move back the playback position while continuing to
record or timer record.
Press
.
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds and
resumes pause.
To Resume Playback Of A TV Broadcast From The
Paused Point
43
1.5x Speed Search
You can play back a title quickly. (This feature can also be
performed with normal playback.)
1.5x speed search cannot be performed during recording on HDD
or DVD.
1 Press 3 to locate the point to start 1.5x speed search from.
2 Press 4 to resume playback.
3 Press 5 once.
● Pressing ON SCREEN displays “+X1.5” on the top right corner of the
screen.
NOTE:
When the unit is connected with a digital audio device using an optional
optical cable, set “DIGITAL AUDIO OUT” to “PCM ONLY”. (墌 pg. 29)
Jump Search
You can locate a scene ahead or behind the current one by
jumping scenes according to selected time intervals (墌 pg. 68)
during playback (or Live Memory Playback). This feature is also
available during recording (or Live Memory Recording) or when
watching a TV received programme.
Press JUMP – or JUMP +.
● To advance forward or back, press JUMP – or JUMP + repeatedly
within 5 seconds of each press to continue jump.
● When you cannot advance any farther (beginning or end of
programme reached), the message “UNABLE TO GO BACK
ANYMORE” appears on the screen and the on-air screen resumes.
In such a case, press 2, 3 or 8.
Example 1:
Playback search when jump interval is set to 30 MIN jumps
Time counter
0 min
40 min
1 h 15 min
30 min
● You cannot use Live Memory Recording for channels other than the
channel you are currently watching.
● Recording speed is automatically set to SP mode when Live Memory
Recording is started.
● Temporarily recorded data prior to the beginning of Live Memory
Recording is erased when Live Memory Recording started.
EN
Beginning of
programme
1h
Current scene
End of programme
Example 2:
Recording search when jump interval is set to 15 MIN jumps
Clock time
9:00
9:15
Beginning of
programme
9:30
9:40
9:45
Current scene
10:15
10:00
End of programme
You can resume playback of a TV broadcast you were recording or
watching from the point you have paused.
1 Press 9 to pause a TV broadcast.
● Recording continues when recording.
2 Press 4 to start Live Memory Playback.
● Playback resumes from the paused position.
3 Press 8 to resume the on-air screen.
Page 43
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_07Timer Recording.fm]
Masterpage:Left0
DR-MH30EU_00.book Page 44 Tuesday, June 29, 2004 5:41 PM
44
EN
TIMER RECORDING
7 The SHOWVIEW number you entered and the matching timerrecording information are displayed on the TV screen. Check the
programme data.
SHOWVIEW Timer Programming
TM
You can programme this unit to timer-record as many as
32 programmes.
With the SHOWVIEW system, timer programming is greatly
simplified because each TV programme has a corresponding code
number which your unit is able to recognize.
You can use the remote control to enter the SHOWVIEW number.
●
●
●
●
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “ShowViewTM System Setup” (墌 pg. 70) and
set the Guide Program number correctly.
8 Press rt to select the desired recording option as required.
Press rt to select the desired setting, then press ENTER.
● “INPUT TITLE” (墌 pg. 50, “Modify Title Name”)
● “CATEGORY” (墌 pg. 51, “Modify Category”)
● “VPS/PDC” (墌 pg. 45, “VPS/PDC Recording”)
● “WEEKLY/DAILY” (墌 pg. 45, “Weekly/Daily Recording”)
● “REC MODE” (墌 pg. 35, “Recording Mode”)
9 Press rt to select “OK”, then press ENTER to access the
Programme Confirmation screen.
Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
CABLE/SAT
TV
● To cancel this setting, press RETURN.
DVD
10 Press w e to select “EXIT”, then press ENTER to complete
0–9
timer programming.
● To programme another timer, press w e to select “CONTINUE”, then
press ENTER.
● If “PROGRAMME OVERLAPPED” appears on the TV screen, see
page 47.
CANCEL
PROGRAMME
NOTES:
ENTER
● There may be cases that SHOWVIEW Timer Programming function
prolongs the stop time of the programming.
● When two successive programmes are recorded on a DVD-RW disc
with SHOWVIEW Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
RETURN
CLEAR
DISPLAY
VPS/PDC#
IMPORTANT:
1 Load a recordable disc if recording to DVD.
2 Press PROGRAMME to access the programme top screen.
3 Press rtw e to select “SHOWVIEW”, then press ENTER.
● When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMES” appears on the TV screen, you need to cancel
some of the reserved programmes. (墌 pg. 47)
4 Press the number keys to
123
enter the SHOWVIEW number of a
programme you wish to record.
PROGRAMME > SHOWVIEW (1/2)
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, the wrong channel number will
be displayed on the SHOWVIEW programme screen in step 7. When
this happens, set the correct Guide Program number for that station.
(墌 pg. 70, “ShowViewTM System Setup”)
Satellite Receiver Users
To timer-record a satellite broadcast using the SHOWVIEW
system:
A Perform “Satellite Receiver Control Setting” (墌 pg. 23).
B Perform “ShowViewTM Timer Programming” (墌 pg. 44).
C Leave the satellite receiver’s power on.
SHOWVIEW NO.
1234
OR
SELECT WITH [
]
THEN PRESS [ENTER]
Press rtw e to select the
desired number key on the
screen, then press ENTER.
Repeat to enter all needed
numbers.
PRESS [PROGRAMME]
TO EXIT
PROGRAMME
ENTER
EXIT
SELECT
1
4
7
DELETE
2
5
8
0
3
6
9
DELETE ALL
DVD
RECORD TO
CONFIRM
5 Press rt to select “RECORD TO”, then press ENTER. Press
rt to select the desired recording deck, then press ENTER.
6 Press rtw e to select “CONFIRM”, then press ENTER.
● If the number you entered is invalid, “SHOWVIEW NO. ERROR
CONFIRM SHOWVIEW NO. THEN RETRY” appears on the TV
screen. Input a valid SHOWVIEW number.
● If “GUIDE PROGRAMME IS NOT SET SET GUIDE PROGRAM
THEN RETRY” appears on the TV screen, set Guide Program
Numbers manually. (墌 pg. 70)
Page 44
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_07Timer Recording.fm]
Masterpage:Right+
DR-MH30EU_07Timer Recording.fm Page 45 Wednesday, June 30, 2004 3:11 PM
TIMER RECORDING
EN
45
Weekly/Daily Recording
VPS/PDC Recording
You can record programmes with one of the following weekly/daily
timer settings.
For the HDD deck
When you select a mode other than ONCE, the space on the hard
disk drive is saved for new recordings by overwriting previous
recordings. To prevent loss of a needed recording, backup
programmes you wish to save by dubbing them to DVD discs
before overwriting previous recordings. Or save the title of weekly/
daily programmes to avoid overwriting of a previous week/day.
(墌 pg. 47)
Now available from some TV stations, PDC (Programme Delivery
Control) and VPS (Video Programme System) are services
designed to assure safe, accurate timer recording. With this
system, special code signals are transmitted together with the
audio/video signals. These code signals control your video unit and
have precedence over the advertised times you may have preset
into the timer. This means that your unit will start and stop
recording when the preset TV programmes actually start and end
— even if the broadcast time of a preset TV programme is
changed.
ONCE (One Time Recording)
NOTES:
In this mode a programme will not be automatically overwritten.
WEEKLY (OVERWRITE) (Weekly Recording/Weekly Overwrite)
When the set weekly programme is broadcast, the programme
recorded last week is automatically deleted and overwritten by the
new programme. Save the title of each programme you wish to
save, then the recorded programme is saved and will not be
overwritten by the new programme.
This week’s drama
Overwritten
Last week’s drama
MON–SUN (FOR A WEEK)/ MON–SAT (FOR A WEEK)/ MON–FRI
(FOR A WEEK) (Daily Recording/Weekly Overwrite)
When the set weekly programme is broadcast, the programme
recorded on the same day last week is automatically deleted and
overwritten by the new programme. Save the title of each
programme you wish to save, then the recorded programme is
saved and will not be overwritten by the new programme.
Overwritten
This
week
MON TUE
WED THU
FRI
Last
week
MON TUE
WED THU
FRI
● Make sure to press VPS/PDC# after completing timer programming
procedure to activate the VPS/PDC recording function.
● When you use Manual Timer Programming, set the start time (VPS
or PDC time) exactly as advertised in the TV listing. A different time
than advertised will result in no recording.
● VPS/PDC recording is also possible when a satellite receiver or a
cable system is connected to L-2 IN/DECODER connector on your
unit.
● VPS/PDC recording is also possible via the L-1 IN/OUT connector.
How to check if the station being received transmits a VPS/
PDC signal
A Hold down DISPLAY for about 5 seconds. “VPS/PDC” appears
blinking on the front display panel. If a VPS/PDC signal is detected
from the station, “VPS/PDC” will stop blinking. If no VPS/PDC
signal is detected from the station, “VPS/PDC” will blink at a slower
rate.
B Press DISPLAY again to return to normal display.
MON–SUN (OVERWRITE)/ MON–SAT (OVERWRITE)/ MON–FRI
(OVERWRITE) (Daily Recording/Daily Overwrite)
When the set daily programme is broadcast, yesterday’s
programme is automatically deleted and overwritten by the new
programme. Save the title of each programme you wish to save,
then the recorded programme is saved and will not be overwritten
by the new programme.
Tuesday’s programme
Overwritten
Monday’s programme
For the DVD deck
ONCE (One Time Recording)
WEEKLY (Weekly Recording)
MON–SUN/ MON–SAT/ MON–FRI (Daily Recording)
Page 45
Wednesday, 30 June 2004 15:11
Filename [DR-MH30EU_07Timer Recording.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 46 Tuesday, June 29, 2004 5:41 PM
46
EN
TIMER RECORDING
6 Press rt to select “START”, then press ENTER. Press rt to
set the desired start time, then press ENTER.
Manual Timer Programming
You can programme this unit to timer-record as many as
32 programmes.
If you do not know the SHOWVIEW number for the programme you
wish to record, use the following procedure to set your unit to
timer-record the programme.
●
●
●
●
7 Press rt to select “STOP”, then press ENTER. Press rt to
set the desired stop time, then press ENTER.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press and
hold rt.
Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
8 Press rt to select “TV PROG”, then press ENTER. Press rt
to select the desired channel.
CABLE/SAT
TV
● Each press of rt advances/goes back the start time in 1-min.
increments.
● To advance/go back the start time in 30-min. increments, press and
hold rt.
9 Press rt to select “CONFIRM”, then press ENTER.
10 Set the other recording options as required.
DVD
● Refer to step 8 in “ShowViewTM Timer Programming” (墌 pg. 44).
11 Press rt to select “OK”,
then press ENTER to access the
Programme Confirmation screen.
12 Press w e to select “EXIT”,
AUX
then press ENTER to complete
timer programming.
● To programme another timer,
press w e to select
“CONTINUE”, then press
ENTER.
PROGRAMME
ENTER
rtwe
2
PROGRAMME > CALENDAR PR. (3/3)
14/01/04 WED 22:30 - 23:00
GARDENING
SELECT WITH [
]
THEN PRESS [ENTER]
INPUT TITLE
PRESS [PROGRAMME]
TO EXIT
VPS/PDC
GARDENING
CATEGORY
WEEKLY/DAILY
EDUCATION
OFF
MON-FRI (FOR A WEEK)
REC MODE
PROGRAMME
ENTER
EXIT
SELECT
BBC1
[EDUCATION] FR360
1:00
28:00
FR360
OK
● If “PROGRAMME OVERLAPPED” appears on the TV screen, see
page 47.
NOTES:
● When two successive programmes are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited programme is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you programmed.
1 Load a recordable disc if recording to DVD.
2 Press PROGRAMME to access the programme top screen.
3 Press rtw e to select “CALENDAR PR.”, then press ENTER.
● When “PROGRAMME FULL DELETE UNWANTED TIMER
PROGRAMMES” appears on the TV screen, you need to cancel
some of the reserved programmes. (墌 pg. 47)
4 Press rtw e to select the desired date, then press ENTER.
5 Press rt to select “RECORD
2
TO”, then press ENTER. Press
rt to select the desired
recording deck, then press
ENTER.
PROGRAMME > CALENDAR PR. (2/3)
14/01/04 WED 22:30 - 23:00
RECORD TO
HDD
START
22:30
PRESS [PROGRAMME]
TO EXIT
[0]: SAT
STOP
23:00
TV PROG
BBC1
ENTER
CONFIRM
EXIT
Page 46
BBC1
[MISC. ] XP
SELECT WITH [
]
THEN PRESS [ENTER]
PROGRAMME
SELECT
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform “Satellite Receiver Control Setting” (墌 pg. 23).
B Perform “Manual Timer Programming” (墌 pg. 46). In step 8,
press AUX to change “TV PROG” to “SAT”. Then press rt to
enter the channel position for the satellite broadcast.
C Leave the satellite receiver’s power on.
Relief Recording
When a programme that is set for the DVD deck cannot be
recorded properly, the programme is recorded to the HDD deck
instead in the same recording mode as set.
● If the remaining capacity of the hard disc is not sufficient, the
programme is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
● If “JUST” is selected for the recording mode, the current recording
mode for the DVD deck is applied.
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_07Timer Recording.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 47 Tuesday, June 29, 2004 5:41 PM
TIMER RECORDING
CABLE/SAT
TV
DVD
EN
47
Check Programmes
To check the whole list of programmes
1 Press PROGRAMME to access the programme top screen.
2 Press rtw e to select “PROGRAMME LIST”, then press
ENTER.
● The details of a selected programme appear on the top of the screen.
● The daily programme of a title is listed as one programme.
PROGRAMME
ENTER
rtwe
To check the list of programmes by date
1 Press PROGRAMME to access the programme top screen.
2 Press rtw e to select “CALENDAR LIST”, then press
ENTER.
3 Press rt to select the desired date, then press ENTER.
Cancel And Change Programmes
● Repeat steps in “Check Programmes” to select a programme before
proceeding.
To cancel the programme
1 Press rtw e to select “CANCEL”, then press ENTER.
To modify the programme settings
1 Press rtw e to select “MODIFY”, then press ENTER.
2 Change the settings of the desired recording options as
required.
● Refer to steps 4 – 12 in “Manual Timer Programming” (墌 pg. 46).
To skip the weekly/daily programmes to the next week/day
It is easy to temporarily cancel weekly/daily programmes of a
week/day.
1 Press rtw e to select “PROGRAMME SKIP”, then press
ENTER.
2 Press w e to select “SKIP”, then press ENTER twice.
To save the titles of weekly/daily programmes (HDD Deck
Only)
Use this function to avoid overwriting titles of weekly/daily
programmes of a previous week/day.
1 Press rtw e to select “TITLE SAVE”, then press ENTER.
2 Press w e to select “SAVE”, then press ENTER twice.
NOTE:
This function is available only when the remaining capacity of the hard
disc is sufficient.
Page 47
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_07Timer Recording.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 48 Tuesday, June 29, 2004 5:41 PM
48
EN
TIMER RECORDING
Automatic Satellite Programme
Recording
● Make sure the satellite receiver is connected to the unit’s L-2 IN/
DECODER connector.
● Programme the timer on the satellite receiver.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
This function allows you to automatically record a satellite
programme which is timer-programmed on your external satellite
receiver. Connect a satellite receiver to the unit’s L-2 IN/
DECODER connector and programme the timer on the satellite
receiver. The unit starts or stops recording by the signals input
from the satellite receiver. After recording, the unit’s power shuts
off automatically.
1 Press HDD or DVD to choose the recording deck.
2 Set “L-2 SELECT” to “SAT VIDEO” or “SAT S-VIDEO”.
(墌 pg. 61)
● Also refer to “IMPORTANT” on page 65.
3 Press REC MODE repeatedly to set the recording mode.
4 Press and hold SAT# for about 2 seconds to engage the
Automatic Satellite Programme Recording mode. “SAT#” appears
on the front display panel.
ATTENTION:
● Be sure not to turn on the satellite receiver before the programme
is executed; otherwise, the unit will start recording when the
satellite receiver’s power is turned on.
● If you have connected another appliance other than a satellite
receiver to the L-2 IN/DECODER connector, be sure not to engage
the Automatic Satellite Programme Recording mode; otherwise,
the unit will start recording when the connected appliance’s power
is turned on.
● Automatic Satellite Programme Recording and timer-recording
cannot be done at the same time.
HDD DVD
CABLE/SAT
TV
HDD
DVD
DVD
NOTES:
● To disengage the Automatic Satellite Programme Recording mode,
press SAT#.
● If the unit’s power is off, it is not possible to engage the Automatic
Satellite Programme Recording mode.
● In step 4, if “SAT#” blinks quickly on the front display panel even
though your satellite receiver’s power is off, Automatic Satellite
Programme Recording will not work properly with that satellite
receiver*. If this is the case, perform “Manual Timer Programming”
(墌 pg. 46) to timer-record a satellite programme.
* Some satellite receivers output signals even if the power is off.
Automatic Satellite Programme Recording is not possible with those
satellite receivers.
● “SAT#” blinks on the front display panel while Automatic Satellite
Programme Recording is in progress.
● For timer programming of the satellite receiver, refer to the instruction
manual of the satellite receiver.
● Automatic Satellite Programme Recording is not possible if your
satellite receiver does not have a timer.
● Pressing the unit’s 1 button while Automatic Satellite Programme
Recording is in progress turns off the unit’s power and disengages
the Automatic Satellite Programme Recording mode.
● If there are more than one satellite programmes you wish to record
with Automatic Satellite Programme Recording, it is not possible to
set different recording modes for each programme.
● Depending on the type of satellite receiver, the unit may not record a
slight portion of the beginning of the programme or may record
slightly longer than the actual length of the programme.
● If you engage the Automatic Satellite Programme Recording mode
when the satellite receiver’s power is on, the unit will not start
Automatic Satellite Programme Recording even though “SAT#”
blinks on the front display panel. When the satellite receiver shuts off
once and is turned back on again, the unit starts recording.
● You can also record a programme from your cable system in the
same way if the system has a timer.
● Just Clock (墌 pg. 73) does not work when the Automatic Satellite
Programme Recording mode is engaged.
REC MODE
SAT#
Page 48
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_08Navigation.fm]
Masterpage:Right0
DR-MH30EU_00.book Page 49 Tuesday, June 29, 2004 5:41 PM
NAVIGATION
The Library Database Navigation enables you to search and select
the desired titles recorded on the HDD deck and the DVD deck
very easily.
You can record up to 99 titles on a disc.
Each time a title is recorded, the information of the title is
registered for the Library Database Navigation automatically.
So, you can confirm the information of the titles recorded with the
Library Database Navigation screen. And, you can also select one
of the titles recorded using the Library Database Navigation.
The following screen appears as the Library Database Navigation
screen when you press NAVIGATION. You can move the arrow to
select the desired position on the screen by pressing rt w e on
the remote control.
NAVIGATION > ORIGINAL
0026 [FISH WORLD
25/12/03 THU 10:00 - 10:15
FROG WORLD
]
143 MIN
PR. 3
[HOBBY] EP
D
B
NAVIGATION
ENTER
EXIT
SELECT
C
About registration of information
The following information is automatically registered for each title
when ordinary recording or timer recording is performed, then
stored in an area specified on the unit.
●
●
●
●
●
●
●
index* (reduced pictures to show programme titles)
programme title*
category*
date and time
channel
recording mode
length of recording time
The items marked with an asterisk (*) can be easily modified and
registered again after recording by using Library Database
Navigation system.
The limitations of registration
You can register information up to 99 titles for the DVD deck and
200 titles for the HDD deck.
When the amount of information is at the limits of registration, you
cannot record new titles any more. In this case, you need to delete
old titles to register new one. (墌 pg. 51)
NOTES:
SELECT WITH [
]
THEN PRESS [ENTER]
PRESS [NAVIGATION]
TO EXIT
49
Using Library Database Navigation system, you can easily modify
registered information, edit the title or play list, as well as search for
the beginning of each title.
Library Database Navigation
A
EN
E
F
G
A Playback screen
(Indicates currently received TV programme.)
B Guidance for operations
C Scroll bar
(Appears when there are over nine registered titles (or play
lists). The scroll bar only indicates that there are more titles (or
play lists) hidden off the current screen display. To show hidden
titles (or play lists), press rt w e repeatedly.)
D Recording information for the title indicated by the arrow
E Index list
(Thumbnail still of each title)
Thumbnail still is not to be played back.
F Index
: Indicates no index is registered.
: Indicates title in standby for timer recording.
: Indicates no title is registered.
G Icons
(Indicate the record condition of each title.)
● Once a DVD-R/RW (Video mode) disc has been finalised, the
displays for original and play list do not appear. Only display for
library appears.
● When you move the title recorded on HDD to DVD, the icon will be
changed to .
● Sound of received channel may be interrupted while the Library
Database Navigation screen is displayed.
The Icons and their meanings
This title is write-protected.
This title has stereo sounds.
This title was recorded with timer recording.
W
This title is Weekly Recording/Weekly Overwrite.
D
This title is Daily Recording/Daily Overwrite.
D
This title is Daily Recording/Weekly Overwrite.
NEW
This title has not been played back.
This title is copy-protected.
This title was just once recordable (copy-once
title).
Page 49
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_08Navigation.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 50 Tuesday, June 29, 2004 5:41 PM
50 EN NAVIGATION
Scan For Beginning Of Title
●
●
●
●
Modify Original Information
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press HDD or DVD to choose the corresponding deck.
Load a DVD disc to scan.
●
●
●
●
CABLE/SAT
TV
HDD
DVD
DVD
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press HDD or DVD to choose the corresponding deck.
Load a DVD disc to modify.
ATTENTION:
It is not possible to modify discs recorded on DVD units from other
manufacturers.
MEMO
Modify Index
NAVIGATION
ENTER
1 Press EDIT. The Editing screen appears.
2 (DVD deck only) Press rt w e to select “MODIFY” under
rtwe
“ORIGINAL/PLAY LIST”, then press ENTER.
4
CLEAR
8
3 Press rt w e to select “MODIFY” under “ORIGINAL”, then
press ENTER.
9
4 Press rt w e to select one title you want to modify, then press
ENTER.
5 Press w e to select “INDEX”.
6 Search for the picture from the
You can scan the beginning of the title easily with the Library
Database Navigation.
1 Press NAVIGATION. The Library Database Navigation screen
appears.
2 Press rt w e to select “ORIGINAL”, then press ENTER.
3 Press rt w e to select the
0026 [FISH WORLD
25/12/03 THU 10:00 - 10:15
FROG WORLD
]
143 MIN
PR. 3
[HOBBY] EP
● When you want the plural titles to
SELECT WITH [
]
THEN PRESS [ENTER]
be played back continuously, press
PRESS [NAVIGATION]
TO EXIT
MEMO after selecting the desired
title. The numbers of the playback
ENTER
NAVIGATION
order appear on the index. You
EXIT
SELECT
can select up to 8 titles.
● When you want to correct the
order, move the arrow to the desired index and press MEMO. The
number disappears and the unit re-numbers the other programmes
automatically.
● When you want to cancel the order, press CLEAR (8).
4 Press w e to select
NAVIGATION > ORIGINAL
“BEGINNING”, then press ENTER.
● To repeat playback of a selected
title, press w e to select
“REPEAT”, then press ENTER.
● To resume playback from the point
where playback was previously
stopped, press w e to select
“RESUME”, then press ENTER.
25/12/03 THU
10:00 - 10:15
FROG WORLD
SP
PR.
3
[HOBBY]
SELECT WITH [
]
THEN PRESS [ENTER]
SELECT HOW TO PLAY BACK
PRESS [NAVIGATION]
TO EXIT
NAVIGATION
ENTER
EXIT
SELECT
BEGINNING
RESUME
7 Confirm the arrow is on
“REPLACE”, then press ENTER to
register new index. New index
appears on the right window.
25/12/03 THU 10:00 - 10:15
FROG WORLD
PR 3
[OTHERS] SP
INDEX
PROG. 1
0 : 01 : 03
SELECT IMAGE TO REPLACE WITH
ON REMOTE
REPLACE
RETURN
● When you press ENTER with the arrow on “RETURN” you can return
to the previous screen.
NAVIGATION > ORIGINAL
index (small pictures) of the
desired title, then press ENTER.
EDITING > MODIFY INDEX
title by pressing the appropriate
buttons (3, 4, 5, or 9). The
pictures of the title appear on the
left window.
REPEAT
8 Press EDIT to return to the normal screen.
Modify Title Name
1 Perform steps 1 – 4 of “Modify Index” (墌 pg. 50) before
continuing.
2 Press rt w e to select “NAME”, then press ENTER.
3 Press rt w e to select the
desired letter or command, then
press ENTER. Repeat this
process to complete the name.
● To correct a letter, press rt w e
to select “DELETE”, then press
ENTER.
● You can enter the letters up to 64.
ABC
EDITING > MODIFY NAME
0026 [FISH WORLD
25/12/03 THU 10:00 - 10:15
FROG WORLD
]
64 MIN
PR. 3
[HOBBY] XP
F R O G WO R L D
SELECT WITH [
]
THEN PRESS [ENTER]
PRESS [EDIT]
TO EXIT
EDIT
ENTER
EXIT
SELECT
A
B
a
b
G
H
I
J
K
L
g
h
i
j
M
N
O
P
Q
R
m
n
o
p
q
S
T
U
C
D
V
W X
s
t
u
v
w
x
Y
Z
y
z
!
"
#
$
;
<
>
?
@
[
'
(
)
,
\
]
^
_
`
{
CANCEL
E
F
% &
.
:
c
DELETE
d
e
k
f
1
2
3
l
4
5
6
r
7
8
9
0
+
-
*
/
=
|
}
~
SAVE
4 Press rt w e to select
“SAVE”, then press ENTER.
5 Press EDIT to return to the normal screen.
5 Press 9 to pause playback.
● To resume normal playback, press 4.
6 Press 8 to stop playback.
Page 50
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_08Navigation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 51 Tuesday, June 29, 2004 5:41 PM
NAVIGATION
EN
Modify Category
Delete Unwanted Part Of The Title (DVD deck only)
1 Perform steps 1 – 4 of “Modify Index” (墌 pg. 50) before
You can delete unwanted part of the title.
1 Perform steps 1 – 3 of “Modify Index” (墌 pg. 50) before
continuing.
continuing.
2 Press rt w e to select “CATEGORY”, then press ENTER.
3 Press rt w e to select the
EDITING > MODIFY CATEGORY
desired category, then press
ENTER.
0026 [FISH WORLD
25/12/03 THU 10:00 - 10:15
FROG WORLD
4 Press EDIT to return to the
SELECT WITH [
]
THEN PRESS [ENTER]
normal screen.
PRESS [EDIT]
TO EXIT
EDIT
ENTER
EXIT
SELECT
MOVIE
MUSIC
]
64 MIN
PR. 3
[HOBBY] XP
ANIMATION
SPORTS
DOCUMENTARY
WEATHER
EDUCATION
HOBBY
ENTERTAINMENT
ART
want to delete, then press ENTER.
elapsed playing time starts counting with the arrow on “IN”.
Protect Title (DVD deck only)
You can protect titles to prevent accidental erasure of the important
titles.
1 Perform steps 1 – 3 of “Modify Index” (墌 pg. 50) before
continuing.
2 Press rt w e to select “PROTECT”, then press ENTER.
3 Press rt w e to select a title you want to protect, then press
ENTER.
4 Press w e to select “PROTECT”, then press ENTER. “
appears.
2 Press rt w e to select “DEL SCENE”, then press ENTER.
3 Press rt w e to select one title whose unwanted part you
4 The playback pictures appear in the window on the screen. The
DRAMA
NEWS
51
”
● To cancel the protection, repeat 3 – 4 again. In step 4, select
“CANCEL PROTECT”, then press ENTER.
5 Press EDIT to return to the normal screen.
NOTE:
All the titles on a disc will be deleted once the disc is formatted even if
they are protected titles. (墌 pg. 51)
5 Find the point where you want
the deletion to begin, then press
ENTER with the arrow on “IN”.
The edit-in time is fixed and the
elapsed playing time starts
counting again.
EDITING > ORIGINAL/DELETE SCENE
21/12/03 SUN 18:30 - 20:00
RALLY CAR
PR. 12
[OTHERS] SP
IN
0 : 05 :15
OUT
0 : 06 :15
PROG. 1
0 : 01 : 03
SELECT IMAGE TO REPLACE WITH
6 Find the point where you want
the deletion to end, then press
ENTER with the arrow on “OUT”.
The edit-out time is fixed.
IN
OUT
ON REMOTE
PREVIEW
OK
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in and edit-out
points.
7 Press w e to select “PREVIEW”, then press ENTER to preview
the edited title.
8 Press w e to select “OK”, then press ENTER.
● If you do not want to delete the scene, press EDIT or RETURN.
To modify the points
A Press EDIT or RETURN.
B Repeat steps 4 – 8 as necessary.
9 Press w e to select “DELETE”, then press ENTER. The
selected scene is deleted.
Delete Title
● To cancel the deletion, press w e to select “CANCEL”, then press
ENTER.
You cannot record any more with Library Database Navigation
once the registered titles on the disc reach 99 titles for the DVD
deck and 200 titles for the HDD deck. Deleting unnecessary titles
after dubbing or other operations can increase remaining time and
available recording capacity. (For DVD-R discs, although it is
possible to delete recorded titles, available recording capacity does
not increase.) The deleted title is never resumed. Play lists and title
information in the unit’s library are also deleted.
10 Press EDIT to return to the normal screen.
NOTES:
● There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
● Available recording capacity may not match the deleted part after
deletion.
1 Press EDIT. The Editing screen appears.
2 Press rt w e to select “DELETE” under “ORIGINAL”, then
press ENTER.
3 Press rt w e to select one title you want to delete, then press
ENTER.
4 Press w e to select “DELETE”, then press ENTER.
● When you cancel the deletion, select “CANCEL”, then press ENTER.
5 Press EDIT to return to the normal screen.
Page 51
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_08Navigation.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 52 Tuesday, June 29, 2004 5:41 PM
52 EN NAVIGATION
Divide Title
Modify Play List Information
1 Press EDIT. The Editing screen appears.
2 Press rt w e to select “DIVIDE”, then press ENTER.
3 Press rt w e to select a title to divide, then press ENTER.
4 Locate a point to divide by pressing the appropriate buttons
(3, 4, 5, or 9).
5 Confirm the arrow is on “DIVIDE”, then press ENTER at the
dividing point.
● The first picture (start) of the newly created title appears in the
bottom right window.
6 Press w e to select “PREVIEW”, then press ENTER.
● The first several seconds of the newly created title is played back,
then the playback pauses at the dividing point.
● To undo the division, press w e to select “RETRY”, then press
ENTER. Repeat the above procedure to locate another point to
divide.
7 Press w e to select “OK”, then press ENTER.
8 Press EDIT to return to the normal screen.
●
●
●
●
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Press HDD or DVD to choose the corresponding deck.
Load a DVD disc to modify.
ATTENTION:
It is not possible to modify discs recorded on DVD units from other
manufacturers.
CABLE/SAT
TV
HDD
DVD
DVD
NOTE:
There may be a discrepancy of several seconds between the scene you
intend to edit, and the scene which is actually edited.
Modify Chapter
You can create and delete chapter marks in titles.
ENTER
1 Perform steps 1 – 4 of “Modify Index” (墌 pg. 50) before
MEMO
EDIT
NAVIGATION
rtwe
continuing.
2 Press rt w e to select “CHAPTER”, then press ENTER.
3 Confirm the arrow is on
EDITING > MODIFY CHAPTER
“MARK”, then press ENTER at
positions you want to mark.
● The newly created chapter is
displayed.
● To undo the marking, press w e to
select “RETRY”, then press
ENTER. Repeat the above
procedure to locate another point
to mark.
CHAPTER 03/10
6
4
5
9
0 : 07 : 01
01 00 : 00 : 00
MARK
02 00 : 05 : 30
03 00 : 07 : 00
ERASE
RETRY
04 00 : 30 : 00
RETURN
4 Press 4, and press 3 or 5 to select one chapter you want
to delete, then press 9.
5 Press w e to select “ERASE”, then press ENTER.
● The selected chapter is deleted.
● To undo the deletion, press w e to select “RETRY”, then press
ENTER. Repeat the above procedure to locate another point to
delete.
6 Press EDIT to return to the normal screen.
NOTE:
There may be a discrepancy of several seconds between the scene you
intend to edit, and the scene which is actually edited.
Page 52
2
3
CLEAR
8
Play List
It is a collection of the scenes. A play list can be freely edited and
played back without ever changing any original recording data.
Using the random access of a disc (which allows video data to be
instantly read no matter where it is on the disc), a play list includes
information such as the timer counter for the playback start point
and end point, indexes for checking the contents of recorded data,
category information, and more. Playback according to a play list
you have created allows you to enjoy various combinations of
video images from a single title.
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_08Navigation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 53 Tuesday, June 29, 2004 5:41 PM
NAVIGATION
Create Play List
Add scenes
1 Press EDIT. The Editing screen appears.
2 (DVD deck only) Press rt w e to select “MODIFY” under
1 Perform steps 1 – 3 in “Edit Scenes” (墌 pg. 53) before
continuing.
3 Press rt w e to select “CREATE”, then press ENTER.
4 Press rt w e to select a title that includes scenes to be
included in a play list, then press ENTER.
Move Scenes
5 The playback pictures appear in the window on the screen. The
elapsed playing time starts counting with the arrow on “IN/OUT”.
1 Perform steps 1 – 3 of “Edit Scenes” (墌 pg. 53) before
continuing.
7 Find the point where you want
the created play list to end, then
press ENTER with the arrow on
“IN/OUT”. The edit-out time is fixed.
EDITING > MODIFY SCENE
TOTAL
SCENE
00 : 00 : 00
PAGE
1/1
1 PRO. 1
2
3
4
PRO. 1
6
7
8
IN
TO
IN/OUT
MODIFY
MOVE
PREVIEW
SELECT TITLE
DELETE
RETRY
OK
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in and edit-out
points.
● The edit-out point must come after the edit-in point.
8 Press rt w e to select “PREVIEW”, then press ENTER to
preview the play list.
9 Press rt w e to select “OK”, then press ENTER. The play list
is created.
To modify the points
A Press w e to select “MODIFY”, then press ENTER.
B Repeat steps 5 – 9 as necessary.
10 Press w e to select “EXIT”, then press ENTER to return to
the normal screen.
NOTES:
● There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
● The title, index and category of the play list can be modified in the
same way as “ORIGINAL”. (墌 pg. 50)
● You can modify the play list that has just been created here by
adding, moving, or deleting unwanted parts to create a digest edition,
etc.
Edit Scenes
1 Press EDIT. The Editing screen appears.
2 Press rt w e to select “MODIFY” under “PLAY LIST”, then
press ENTER.
3 Press rt w e to select a play list to modify, then press
ENTER.
4 Press rt w e to select “SCENE”, then press ENTER.
5 Press rt w e to select “MODIFY”, then press ENTER.
6 Press rt w e to select a scene to modify, then press ENTER.
7 Perform steps 5 – 10 in “Create Play List” (墌 pg. 53).
Page 53
2 Press rt w e to select “MOVE”, then press ENTER.
3 Press rt to select a scene to move, then press ENTER.
4 Press rt to select another scene to which the scene is to be
moved, then press ENTER.
5
0 : 00 :15
53
2 Press rt w e to select “SELECT TITLE”, then press ENTER.
3 Perform steps 4 – 10 in “Create Play List” (墌 pg. 53).
“ORIGINAL/PLAY LIST”, then press ENTER.
6 Find the point where you want
the created play list to begin, then
press ENTER with the arrow on
“IN/OUT”. The edit-in time is fixed
and the elapsed playing time
starts counting again.
EN
● To cancel the move, press rt w e to select “RETRY”, then press
ENTER.
5 Perform steps 8 – 10 in “Create Play List” (墌 pg. 53).
Delete Scenes
1 Perform steps 1 – 4 of “Create Play List” (墌 pg. 53) before
continuing.
2 Press rt w e to select “DELETE”, then press ENTER.
3 Press rt to select a scene to delete, then press ENTER.
4 Perform steps 8 – 10 in “Create Play List” (墌 pg. 53).
Play Back Play List
1 Press NAVIGATION. The Library Database Navigation screen
appears.
2 Press rt w e to select “PLAY LIST”, then press ENTER.
3 Press rt w e to select the
NAVIGATION > PLAY LIST
index (small pictures) of the
desired play list, then press
ENTER.
]
0026 [FISH WORLD
026 CREATED 26/12/03 FRI
TEDDY BEAR 25/12
001
143 MIN
[MOVIE]
002
003
SELECT WITH [
]
THEN PRESS [ENTER]
● When you want the plural play lists
PRESS [NAVIGATION]
TO EXIT
to be played back continuously,
press MEMO after selecting the
ENTER
NAVIGATION
EXIT
SELECT
desired play lists. The numbers of
the playback order appear on the
index. You can select up to 30 play lists.
● When you want to correct the order, move the arrow to the desired
index and press MEMO. The number disappears and the unit renumbers the other play lists automatically.
● When you want to cancel the order, press CLEAR (8).
004
005
006
007
008
009
4 Press w e to select “BEGINNING”, then press ENTER. The
playback starts.
5 Press 9 to pause playback.
● To resume normal playback, press 4.
6 Press 8 to stop playback.
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_08Navigation.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 54 Tuesday, June 29, 2004 5:41 PM
54 EN NAVIGATION
Delete Play List
1 Press EDIT. The Editing screen appears.
2 Press rt w e to select “DELETE” under “PLAY LIST”, then
Modify Library Information
press ENTER.
3 Press rt w e to select one play list you want to delete, then
press ENTER.
4 Press w e to select “DELETE”, then press ENTER.
● When you cancel the deletion, select “CANCEL”, then press ENTER.
5 Press EDIT to return to the normal screen.
NOTE:
Even if a play list is deleted, the titles recorded and the library
information are not affected at all.
Title information can be registered in the unit’s memory for up to
600 DVD discs, 2,000 titles. It is helpful when finding a desired title
(or play list) by sorting according to the sort options registered
during (or after) recording.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
Modify Index
CABLE/SAT
TV
A Perform steps 1 – 3 of “Edit Scenes” (墌 pg. 53) before
continuing.
B Perform steps 5 – 8 of “Modify Index” (墌 pg. 50).
HDD
DVD
DVD
Modify Play List Name
A Perform steps 1 – 3 of “Edit Scenes” (墌 pg. 53) before
continuing.
B Perform steps 2 – 5 of “Modify Title Name” (墌 pg. 50).
NAVIGATION
ENTER
Modify Category
rtwe
A Perform steps 1 – 3 of “Edit Scenes” (墌 pg. 53) before
continuing.
B Perform steps 2 – 4 of “Modify Category” (墌 pg. 51).
Scan For Title From Library
1 Press NAVIGATION. The Library Database Navigation screen
appears.
2 Press rt w e to select the
appropriate sort button to sort the
information, then press ENTER.
“DATE” : Sort by date
“DISC No.” : Sort by disc number
“CATEGORY” : Sort by category
“NAME” : Sort by name
● “DATE” and “DISC No.” are available
for the DVD deck only.
NAVIGATION
DVD NAVIGATION
ORIGINAL
PLAY LIST
SELECT WITH [
]
THEN PRESS [ENTER]
PRESS [NAVIGATION]
TO EXIT
DVD LIBRARY
DATE
NAVIGATION
ENTER
EXIT
SELECT
CATEGORY
DISC No.
A
NAME
3 Press rt w e to select the desired title, then press ENTER.
● Playback begins automatically after the selected title is located.
NOTE:
If a disc registered in the library is recorded or modified on DVD units
from other manufacturers, it may become impossible to operate
properly.
Register Disc
When a disc that is not registered in the library is loaded, a
message appears confirming if the disc should be registered. If
registering, perform the following procedure.
1 Press w e to select “REGISTER”, then press ENTER to confirm
the registration.
2 Press NAVIGATION to return to the normal screen.
NOTES:
● It is not possible to register discs formatted on devices other than
JVC’s DVD recorders.
● It is not possible to register discs recorded on devices other than
JVC’s DVD recorders.
● It is not possible to register discs when “SAVE AS LIBRARY” is set to
“OFF”. (墌 pg. 68)
Page 54
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_08Navigation.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 55 Tuesday, June 29, 2004 5:41 PM
NAVIGATION
Playback With MP3/WMA/JPEG
Navigation
EN
55
Locating The Desired Group And Tracks
1 Load a disc.
2 Press NAVIGATION.
3 Press rt w e to select “ORIGINAL”, then press ENTER.
4 Press rt to select the desired
NAVIGATION > ORIGINAL
group, then press ENTER.
This unit can play back discs that MP3/WMA sound files and JPEG
image files taken with digital still cameras or other devices are
recorded.
The MP3/WMA/JPEG Navigation enables you to search and select
the desired files recorded on CD-R/RW or CD-ROM discs very
easily.
NAVIGATION > ORIGINAL
GROUP : 001/100
IT’S SHOWTIME ! ! /B’z
TRACK : 001/100
0 : 07 : 01
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
CLUB
003. SEXY GUY/GOMAKI
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
FOREIGN GROUP
006. REASON/ASAMI
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
A Selected group number/total number of groups on the disc
B Selected file number/total number of files in the group that
contains the selected file
C Elapsed time (MP3 only)
D Name of the selected file
E Group name
F Selected file
● A list of files in the selected group
appears.
5 Press rt to select the desired
item, then press ENTER. The unit
starts playback from the selected
item.
● The unit stops when all items in
the selected group are played
back.
GROUP : 001/100
IT’S SHOWTIME ! ! /B’z
TRACK : 001/100
0 : 07 : 01
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
CLUB
003. SEXY GUY/GOMAKI
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
FOREIGN GROUP
006. REASON/ASAMI
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
NAVIGATION > ORIGINAL
GROUP : 001/100
IT’S SHOWTIME ! ! /B’z
TRACK : 001/100
0 : 07 : 01
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
CLUB
003. SEXY GUY/GOMAKI
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
FOREIGN GROUP
006. REASON/ASAMI
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
NOTES:
● If you press SELECT (4) instead
of ENTER in step 4, the unit starts playback from the first file of the
group.
● JPEG files are played back as a slide show at the set intervals.
(墌 pg. 33)
● If a file name includes any 2-byte character, the unit may not show
the file name correctly.
● The order of the groups and items shown in steps 4 and 5 may differ
from the order shown on your PC.
NOTE:
If there are more than 100 files the rest files are not displayed. In such a
case, press ON SCREEN to display them on the TV screen.
Page 55
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Left0
DR-MH30EU_09Editing.fm Page 56 Monday, July 5, 2004 11:48 AM
56
EN
EDITING
NOTES:
Dubbing
● Play lists are dubbed as programmes.
● In Video mode, if the selected play list includes the scenes recorded
in the different transfer rate, the dubbing is performed in the highest
transfer rate of the scenes in the selected play list.
● It is not possible during dubbing to play back on HDD or DVD or to set
timer-programming.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
CABLE/SAT
TV
DVD
Just Dubbing (From HDD To DVD)
By using Just Dubbing function, when dubbing all selected original
recordings and/or play lists, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the selected recordings and/or play lists to be dubbed
and the available disc space.
MARK
DUBBING
ENTER
rtwe
1 Load a recordable disc.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “JUST”, then press ENTER.
4 Perform steps 4 – 5 of “High Speed Dubbing (From HDD To
DVD)”.
NOTES:
ON SCREEN
● Play lists are dubbed as programmes.
● In Video mode, if the selected play list includes the scenes recorded
in the different transfer rate, the dubbing is performed in the highest
transfer rate of the scenes in the selected play list. However, the
lower transfer rate cannot be dubbed in the higher transfer rate.
● It is not possible during dubbing to play back on HDD or DVD or to set
timer-programming.
NOTE:
It is not possible to dub simultaneously when timer-programming is set.
Select either dubbing or timer-programming.
High Speed Dubbing (From HDD To DVD)
It is possible to dub the original recordings and/or play lists on the
HDD deck to DVD discs. The dubbing is performed in high speed,
keeping the original transfer rate.
NOTES:
● After accessing the Dubbing Menu screen, it is not possible to take
out a disc.
● It is not possible to dub copy-once titles in Video mode.
● When the dubbing is finished, the data will be moved from HDD to
DVD.
● When you cancel dubbing a copy-once title during dubbing, the
original recording on the HDD deck remains and the title copied to a
DVD disc is deleted.
● It is not possible to dub play lists which contain copy-once titles.
● It is not possible to dub the following programmes to DVD-R/RW disc
(Video mode):
•
•
•
•
which contains more than one audio language.
which is on the play list.
which is edited (also Live Memory Recording).
which is recorded in LP mode or FP155-FP240 mode.
● Recording may not be performed in the highest speed depending on
the characteristics of the disc used.
1 Load a recordable disc.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “HIGH SPEED”, then press ENTER.
4 Press rtw e to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
5 Press w e to select “EXECUTE” or “AUTO POWER OFF”, then
press ENTER. The dubbing screen appears for 5 seconds. To
display the dubbing screen again, press ON SCREEN.
EXECUTE: Select this to continue the dubbing operations.
AUTO POWER OFF: Select this to continue the dubbing operations
and turn off the unit after dubbing. While the dubbing screen is
displayed, you can also select this mode by pressing DUBBING.
CANCEL: Select this to cancel dubbing operation.
Page 56
Monday, 5 July 2004 11:47
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Right+
DR-MH30EU_09Editing.fm Page 57 Friday, July 2, 2004 1:29 PM
EDITING
Manual Dubbing (From HDD To DVD)
It is possible to perform dubbing in the desired transfer rate.
1 Load a recordable disc.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “MANUAL”, then press ENTER.
4 Perform step 4 of “High Speed Dubbing (From HDD To DVD)”.
EN
57
About Disc Remaining Display
The unit displays the time information for dubbing by bar meter. By
comparing the disc remaining time and the necessary time for
dubbing of the selected items, it is possible to check if the dubbing
can be performed completely or not.
When performing the High Speed Dubbing
Capacity of a disc
Remaining capacity
The Manual Dubbing screen appears.
5 Press rt to select “REC MODE”, then press ENTER. Press
rt to select the desired option, then press ENTER. The
confirmation screen appears.
NOTES:
● In Video mode, if the selected play list includes the scenes recorded
in the different transfer rate, the dubbing is performed in the highest
transfer rate of the scenes in the selected play list. However, the
lower transfer rate cannot be dubbed in the higher transfer rate.
● It is not possible during dubbing to play back on HDD or DVD or to set
timer-programming.
Original Dubbing (From DVD To HDD)
It is possible to dub the original recordings on DVD discs to the
HDD deck.
1 Load a disc you want to dub.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “TITLE”, then press ENTER.
4 Press rtw e to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
5 Press rt to select “EXECUTE” or “AUTO POWER OFF”, then
press ENTER to start dubbing.
EXECUTE: Select this to continue the dubbing operations.
AUTO POWER OFF: Select this to continue the dubbing operations
21%
Dark green: Length of already recorded item
Light green: Length of selected item
Yellow: Length of the item now being selected by arrow
Red: Excess over the capacity
When performing the Just Dubbing
TOTAL 105MIN
● The unit displays the status on the assumption that the selected
items are dubbed in the lowest transfer rate.
● The total time of a loaded disc is displayed on the right of the bar
meter.
When performing the Manual Dubbing
MAX
FR240
● The unit displays the status on the assumption that the selected
items are dubbed in the lowest transfer rate.
● The available highest transfer rate is displayed on the right of the bar
meter.
NOTE:
The bar meter moves up and down regularly, but this is not a
malfunction.
and turn off the unit after dubbing.
CANCEL: Select this to cancel dubbing operation.
6 Press w e to select “EXECUTE”, then press ENTER for
confirmation. The dubbing screen appears for 5 seconds.
NOTES:
● It is not possible to dub play lists on DVD discs.
● It is not possible to dub pre-recorded DVD VIDEO discs.
Page 57
Friday, 2 July 2004 13:29
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Left+
DR-MH30EU_09Editing.fm Page 58 Monday, July 5, 2004 10:00 AM
58
EDITING
EN
8 Locate the point from where you want to start dubbing, then
DV Dubbing
You can dub programmes from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
NOTES:
● Use the DV cable VC-VDV 204U for connection.
● When you connect a PC to the DV IN connector, we do not assure
the normal operation of this unit.
Your unit
stop or pause playback by pressing the following buttons on the
remote control: 4, 5, 3, 8, 9
● To play back in slow speed (1/10 of the normal speed), press 9 to
pause playback, then press 3 or 5.
● To play back frame-by-frame, press 9 to pause playback, then press
9 repeatedly. Each press of 9 advances a frame.
● To change the playback direction, press 3 or 5.
9 Press w e to select
, then press ENTER. The
dubbing starts.
● Playback on the external DV equipment and recording on the unit
should start simultaneously.
● To pause dubbing, press w e to select
, then press
ENTER. Both the unit and the external DV equipment pause dubbing.
Pressing 9 on the unit also works the same way.
10Press w e to select
, then press ENTER. Then
press 8. The DV equipment stops.
11Press w e to select
, then press ENTER.
12Press 8 twice on the remote control to stop dubbing.
● Both the unit and the external DV equipment stop dubbing.
DV IN connector
NOTES:
Camcorder
● Dubbing copyright guarded programmes is not possible.
● Original DV informations such as the recording date and time are not
recorded.
● The superimposed indication during the operation or dubbing is not
recorded.
● If the dubbing is paused while the channel is set to “DV”, you cannot
switch channels.
DV cable
(VC-VDV 204U)
(not provided)
When you dub from DV equipment other than a
camcorder
A Perform step 1 to 4.
B Locate the point from where you want to start dubbing,
then stop on the DV equipment.
● If you pause the DV equipment in this step, a few second’s
still picture will be recorded at the beginning of the recorded
programme.
DV connector
DV equipment
C Set the input mode to “DV INPUT” on the DV equipment.
● If you select an input mode other than “DV INPUT”, unwanted
pictures may be recorded at the beginning of the recorded
programme.
D Perform step 9 to 12.
1 Connect a camcorder or DV equipment to the DV IN connector
on the unit’s front panel.
2 Press HDD.
3 Press PR +/– to set the channel to “DV”.
4 Press ON SCREEN.
To skip unwanted part of the source picture
Press ENTER to stop both equipment, then press w e to select
.
Locate the point where you want to restart dubbing by pressing 4,
5, or 3, then press 8.
Press w e to select
, then press ENTER to restart
dubbing.
● The on-screen display for DV dubbing appears.
5 Press w e to select
, then press ENTER to display
the remote icon (facing to the right) for the DV equipment.
6 Press w e to select
, then press ENTER
repeatedly until the desired sound
track appears on the TV screen.
HDD
FR360
12bit
0:00
1:00
00:00:00. 00
DV
JVC
2:00
GR-DV3500
00:00:00. 00
DV
L – R
SOUND1
GR-DV3500
AUDIO 1: Select this to record the
original stereo sound played
back on the connected DV
equipment.
AUDIO 2: Select this to record the
dubbed stereo sound played back on the connected DV
equipment.
MIX: Select this to record the sound of both “AUDIO 1” and
“AUDIO 2”.
DV
DV
1 2
● Note that this selection is not available when the source programme
is recorded in 16BIT (48 kHz) mode.
7 Press REC MODE repeatedly to set the recording mode.
Page 58
Monday, 5 July 2004 09:57
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 59 Tuesday, June 29, 2004 5:41 PM
EDITING
Edit From A Camcorder
EN
59
● Slide the TV/CABLE/SAT/DVD switch to DVD.
You can use a camcorder as the source player and your unit as the
recording deck.
A If the camcorder has no S-VIDEO output connector:
AUDIO/VIDEO input
1 Make connections.
A If the camcorder has no S-VIDEO output connector:
— connect the camcorder’s AUDIO/VIDEO OUT connectors to the
unit’s AUDIO/VIDEO input connectors on the front panel.
● When using a monaural camcorder, connect its AUDIO OUT
connector to the AUDIO L input connector on your unit.
B If the camcorder has an S-VIDEO output connector:
— connect the camcorder’s AUDIO OUT and S-VIDEO OUT
connectors to the unit’s AUDIO and S-VIDEO input connectors on
the front panel.
2 Press HDD or DVD repeatedly to select the recording deck.
3 Press PR +/– to select “F-1”.
Recorder
● Set “F-1 INPUT” to “VIDEO” for the VIDEO input connector, or
“S-VIDEO” for the S-VIDEO input connector, depending on the
connector being used. (墌 pg. 62)
Audio/video cable
(not provided)
4 Press REC MODE repeatedly to set the recording mode.
5 Start playback on the camcorder slightly before the actual point
from where you wish to start dubbing.
6 Press 7 on the unit to start recording. Or press and hold 7 and
press 4 on the remote control. The dubbing starts.
7 Press 8 on the unit, then stop playback on the camcorder.
NOTES:
AUDIO/VIDEO OUT
● All necessary cables can be obtained from your dealer.
● Refer to the camcorder’s instruction manual for operating procedure.
● The quality of dubbed picture becomes poorer than that of the
original.
Player
B If the camcorder has an S-VIDEO output connector:
S-VIDEO input
AUDIO input
Recorder
S-video cable
(not provided)
S-VIDEO OUT
AUDIO OUT
Audio cable
(not provided)
Player
Page 59
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 60 Tuesday, June 29, 2004 5:41 PM
60
EN
EDITING
Edit To Or From Another Recorder
You can use your unit as the source player or as the recording
deck.
NOTE:
When using another recorder as the recording deck, refer to its
instruction manual.
A When using your unit as the source player:
TV receiver
Your unit
Player
● Slide the TV/CABLE/SAT/DVD switch to DVD.
1 Connect another recorder’s 21-pin SCART connector to the
unit’s 21-pin SCART connector as illustrated.
A When using your unit as the source player:
— connect its L-1 IN/OUT connector to the recording deck.
B When using your unit as the recording deck:
— connect its L-2 IN/DECODER connector to the source
player.
● If another recorder is compatible with the Y/C signal:
— when using your unit as the source player, set “L-1 OUTPUT” to
“SCART S-VIDEO”. (墌 pg. 61)
— when using your unit as the recording deck, set “L-2 SELECT” to
“S-VIDEO”. (墌 pg. 61)
2 When using this unit as the recording deck, press HDD or DVD
to select the recording deck.
3 When using this unit as the recording deck, press PR +/– to
21-pin SCART cable
(provided)
select “L-2”.
● Set “L-2 SELECT” to “VIDEO” or “S-VIDEO”. (墌 pg. 61)
4 When using this unit as the recording deck, press REC MODE
repeatedly to set the recording mode.
21-pin SCART cable
(not provided)
5 Engage the Play mode of the source player.
6 Engage the Record mode of the recording deck.
7 Stop recording on the recording deck, then stop playback on the
Another recorder
source player.
Recorder
NOTES:
B When using your unit as the recording deck:
TV receiver
Your unit
Recorder
● All necessary cables can be obtained from your dealer.
● For Y/C signal input/output, be sure to use a 21-pin SCART cable
that is compatible with the Y/C signal.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting. (墌 pg. 69)
● If you are using another recorder with S-Video and Audio output
connectors, connect its S-Video and Audio output connectors to this
unit’s S-VIDEO and AUDIO input connectors on the front panel.
Then, set the unit’s input mode to “F-1” in step 3, and set “F-1 INPUT”
to “S-VIDEO”. (墌 pg. 62)
21-pin SCART cable
(provided)
21-pin SCART cable
(not provided)
Another recorder
Player
Page 60
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 61 Tuesday, June 29, 2004 5:41 PM
EDITING
EN
61
COMPONENT: If a connected appliance’s input is compatible with
Output/Input Set
Y/PB/PR signals, set to “COMPONENT”. You can obtain a highquality Y/PB/PR picture. Switch the TV to the input that you can
watch component video pictures.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
8 L-1 INPUT — VIDEO / S-VIDEO
VIDEO: If a connected appliance’s output is compatible only with
CABLE/SAT
TV
regular video signals, set to “VIDEO”.
DVD
S-VIDEO: If a connected appliance’s output is compatible with Y/C
signals, set to “S-VIDEO”. You can obtain a high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
NOTES:
● If “L-1 OUTPUT” is set to “SCART S-VIDEO”, “SCART RGB” or
“COMPONENT”, it is not possible to set “L-1 INPUT” to “S-VIDEO”.
● If “L-2 SELECT” is set to “DECODER”, it is not possible to set “L-1
INPUT” to “S-VIDEO”.
● If “L-2 SELECT” is set to “DECODER”, it is only possible to set “L-1
OUTPUT” to “SCART VIDEO”.
● Component video signals are not output from the L-1 IN/OUT
connector.
● When Progressive scan mode is engaged, it is not possible to select
the setting of “L-1 OUTPUT”. (墌 pg. 69)
ENTER
rtwe
L-2 Select Setting
Set “L-2 SELECT” to the appropriate mode depending on the type
of appliance connected to the unit’s L-2 IN/DECODER connector.
SET UP
1 Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting” on
the left column.
2 Press rt to select “L-2 SELECT”, then press ENTER.
3 Press rt to select the
L-1 Output And L-1 Input Setting
DVD VIDEO SET UP HDD/DVD SET UP
The L-1 IN/OUT connector accepts and delivers either a composite
signal (regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set “L-1
OUTPUT” and “L-1 INPUT” to the appropriate mode depending on
the type of appliance connected to the unit’s L-1 IN/OUT
connector.
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “FUNCTION SET UP”, then press t.
3 Press w e to select “VIDEO IN/
DVD VIDEO SET UP HDD/DVD SET UP
OUT”, then press t.
4 Press rt to select “L-1
OUTPUT” or “L-1 INPUT”, then
press ENTER.
REC/PLAY SET UP
DISPLAY SET
FUNCTION SET UP
VIDEO IN/OUT
MONITOR TYPE
4 : 3LB
F-1 INPUT
VIDEO
L-1 OUTPUT
SCART VIDEO
L-1 INPUT
VIDEO
L-2 SELECT
5 Press rt to select the
appropriate setting, then press
ENTER.
INITIAL SET UP
VIDEO
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
DVD VIDEO SET UP HDD/DVD SET UP
REC/PLAY SET UP
DISPLAY SET
MONITOR TYPE
FUNCTION SET UP
INITIAL SET UP
VIDEO IN/OUT
4 : 3LB
6 Press SET UP to complete the
F-1 INPUT
VIDEO
L-1 INPUT
SCART VIDEO
setting.
L-1 OUTPUT
VIDEO
SCART VIDEO
SCART S-VIDEO
VIDEO
SCART RGB
COMPONENT
L-2 SELECT
* The boldface settings below
indicate the settings at your
purchase.
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
8 L-1 OUTPUT — SCART VIDEO / SCART S-VIDEO / SCART
RGB / COMPONENT
SCART VIDEO: If a connected appliance’s input is compatible only
with regular video signals, set to “SCART VIDEO”.
appropriate setting, then press
ENTER.
4 Press SET UP to complete the
setting.
REC/PLAY SET UP
DISPLAY SET
MONITOR TYPE
F-1 INPUT
INITIAL SET UP
VIDEO IN/OUT
4 : 3LB
VIDEO
L-1 INPUT
VIDEO
L-1 OUTPUT
L-2 SELECT
* The boldface settings below
indicate the settings at your
purchase.
FUNCTION SET UP
SET UP
ENTER
EXIT
SELECT
SCART VIDEO
VIDEO
S-VIDEO
VIDEO
SAT VIDEO
SAT S-VIDEO
DECODER
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
8 L-2 SELECT — VIDEO / S-VIDEO / SAT VIDEO / SAT
S-VIDEO / DECODER
Select “VIDEO” or “S-VIDEO” to use this unit as the recording deck
with the player connected to the L-2 IN/DECODER connector, or to
use the satellite receiver connected to the L-2 IN/DECODER
connector.
VIDEO: If a connected appliance’s output is compatible only with
regular video signals, set to “VIDEO”.
S-VIDEO: If a connected appliance’s output is compatible with Y/C
signals, set to “S-VIDEO”. You can obtain high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
Select “SAT VIDEO” or “SAT S-VIDEO” to view a satellite
programme with the TV set while the unit is turned off. (墌 pg. 65)
SAT VIDEO: If a connected satellite receiver’s output is compatible
only with regular video signals, set to “SAT VIDEO”.
SAT S-VIDEO: If a connected satellite receiver’s output is
compatible with Y/C signals, set to “SAT S-VIDEO”. You can
obtain a high-quality S-VHS picture. (For connection, be sure to
use a 21-pin SCART cable that is compatible with the Y/C signal.)
DECODER: To use a decoder connected to the L-2 IN/DECODER
connector.
SCART S-VIDEO: If a connected appliance’s input is compatible
with Y/C signals, set to “SCART S-VIDEO”. You can obtain highquality picture. (For connection, be sure to use a 21-pin SCART
cable that is compatible with the Y/C signal.)
SCART RGB: If a connected appliance’s input is compatible with
RGB signals, set to “SCART RGB”. You can obtain a high-quality
RGB picture.
Page 61
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 62 Tuesday, June 29, 2004 5:41 PM
62
EN
EDITING
NOTES:
● If you have a satellite receiver or a decoder connected to the L-2 IN/
DECODER connector, be sure to set “L-2 SELECT” back to
appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to the L-2
IN/DECODER connector, leave “L-2 SELECT” set to “VIDEO”.
● When “L-2 SELECT” is set to “SAT VIDEO” and “SAT S-VIDEO”,
“SAT” appears on the TV screen or front display panel instead of
“L-2”.
● If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible to set
“L-2 SELECT” to “DECODER” or “SAT VIDEO”.
● If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to set “L-2
SELECT” to “DECODER” or “SAT S-VIDEO”.
● If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” to “SAT
VIDEO”, “SAT S-VIDEO” or “DECODER”, be sure to connect the L-1
IN/OUT connector with a TV.
Digital Audio Dubbing
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
However, it is not possible to dub copy-protected discs.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
Example: Dubbing to an MD
Recorder
F-1 Input Setting
Set “F-1 INPUT” to the appropriate mode depending on the
connector (VIDEO or S-VIDEO) being used on the front panel.
Digital audio device
(MD deck, etc.)
1 Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting”
(墌 pg. 61).
2 Press rt to select “F-1 INPUT”, then press ENTER.
3 Press rt to select the
DVD VIDEO SET UP HDD/DVD SET UP
appropriate setting, then press
ENTER.
REC/PLAY SET UP
DISPLAY SET
MONITOR TYPE
FUNCTION SET UP
L-1 INPUT
setting.
L-1 OUTPUT
SCART VIDEO
L-2 SELECT
VIDEO
* The boldface settings below
indicate the settings at your
purchase.
VIDEO
VIDEO
VIDEO S-VIDEO
SET UP
ENTER
EXIT
SELECT
Coaxial cable
(not provided)
4 : 3LB
4 Press SET UP to complete the
F-1 INPUT
Optical cable
(not provided)
INITIAL SET UP
VIDEO IN/OUT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
DIGITAL OUT
(COAXIAL)
Player
8 F-1 INPUT — VIDEO / S-VIDEO
VIDEO: When connecting an appliance to the VIDEO input
Rear of unit
connector, set to “VIDEO”.
S-VIDEO: When connecting an appliance to the S-VIDEO input
connector, set to “S-VIDEO”.
DIGITAL OUT
(OPTICAL)
Note for connection:
Remove the protection cap from the cable.
1 Connect the unit and a digital audio device using either an
optional optical cable or an optional coaxial cable.
2 Place a disc on the unit and load an MD on the connected digital
audio device.
3 Select the audio to be dubbed.
4 Start playback slightly before the actual point from where you
wish to start dubbing.
5 Press 9 to pause playback.
6 Select the input mode on the connected digital audio device.
7 Press 4 to start playback on the unit.
8 Start recording on the digital audio device.
9 Stop recording on the digital audio device. Then press 8 to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where you
intend editing to start, and where it actually starts.
Page 62
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Right0
DR-MH30EU_00.book Page 63 Tuesday, June 29, 2004 5:41 PM
REMOTE CONTROL
Remote Control Functions
EN
63
CABLE/SAT
TV
TV AV/VIDEO
1
Remote Control 1/2/3/4 Code Switching
The remote control is capable of controlling four JVC video units
independently. Each of the units can respond to one of four codes
(1, 2, 3 or 4). The remote control is preset to send 3 code signals
because your unit is initially set to respond to 3 code signals. You
can easily modify your unit to respond to 1, 2 or 4 code signals.
DVD
TV% +/–
0–9
PR +/–
TV
Slide the TV/CABLE/SAT/DVD switch to DVD.
ENTER
4
1
SET UP
CABLE/SAT
TV
DVD
TV Multi-Brand Remote Control
1–4
Your remote control can operate the basic functions of your TV set.
In addition to JVC TVs, other manufacturer’s TVs can also be
controlled.
● Turn off the TV using its remote control.
● Slide the TV/CABLE/SAT/DVD switch to TV.
ENTER
IMPORTANT:
Although the provided remote control unit is compatible with JVC
televisions, as well as many other models, it may not work with your TV,
or in some instances, may have limited function capability.
● Keep pressing SET UP down during step 1.
8
1 Enter your TV’s brand code using the number keys, then press
ENTER.
SET UP
● Keep pressing SET UP down during step 1.
1 Press the number key “1” for 1, “2” for 2, “3” for 3 or “4” for 4
2 Press 1 on the unit’s remote control to turn on the TV and try
operations (墌 step 3).
● Once you have set the remote control to operate the TV, you do not
have to repeat this step until you replace your remote control’s
batteries.
● Some brands of TVs have more than one code. If the TV does not
function with one code, try entering another.
to change the remote control code, then press ENTER.
3 Press the corresponding buttons to operate the TV: 1, TV AV/
2 Press 1 on the unit to turn off the unit.
3 Press 4 on the unit for over 5 seconds while the unit is turned
● For some brands of TVs, you must press ENTER after having
pressed the number keys.
off. The code currently set appears on the front display panel.
4 Press 8 on the remote control to change the unit’s code. The
code currently set on the remote control blinks on the front display
panel for approximately 5 seconds, and is applied to the unit.
NOTE:
When “POWER SAVE” is set to “ON” (墌 pg. 69), it is not possible to
change the remote code.
Page 63
VIDEO, PR +/–, TV% +/–, TV
, number keys.
BRAND NAME
CODE
JVC
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SHARP
SONY
SAMSUNG
SANYO
SEARS
TOSHIBA
ZENITH
01, 03
10
02
03
04, 11
05
06
07
12
13
13
08
09
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 64 Tuesday, June 29, 2004 5:41 PM
64 EN REMOTE CONTROL
Satellite Receiver Multi-Brand Remote Control
Your remote control can operate the basic functions of your
satellite receiver set. In addition to JVC satellite receivers, other
manufacturer’s satellite receivers can also be controlled.
● Slide the TV/CABLE/SAT/DVD switch to CABLE/SAT.
IMPORTANT:
Although the provided remote control unit is compatible with JVC
satellite receivers, as well as many other models, it may not work with
your satellite receiver, or in some instances, may have limited function
capability.
● Keep pressing SET UP down during step 1.
1 Enter your satellite receiver’s brand code using the number
keys, then press ENTER.
2 Press 1 on the unit’s remote control to turn on the satellite
receiver and try operations (墌 step 3).
● Once you have set the remote control to operate the satellite receiver,
you do not have to repeat this step until you replace your remote
control’s batteries.
● Some brands of satellite receivers have more than one code. If the
satellite receiver does not function with one code, try entering
another.
3 Press the corresponding buttons to operate the satellite
receiver: 1, PR +/–, number keys.
● For some brands of satellite receivers, you must press ENTER after
having pressed the number keys.
● The number keys may not function with some satellite receivers.
Page 64
BRAND NAME
CODE
JVC
AMSTRAD
CANAL SATELLITE
CANAL +
D-BOX
ECHOSTAR (VIA DIGITAL)
FINLUX
FORCE
GALAXIS
GRUNDIG
HIRSCHMANN
HUMAX
ITT NOKIA
KATHREIN
LUXOR
MASCOM
MASPRO
NOKIA
PACE
PANASONIC
PHILIPS
RADIX
RFT
SABA
SAGEM
SALORA
SAMSUNG
SIEMENS
SKYMASTER
TECHNISAT
THOMSON
TPS
TRIAX
WISI
73
60, 61, 62, 63, 92
81
81
85
82
68
89
88
64, 65, 102
64, 78, 99
88
68
70, 71, 96
68
93
70
87, 94
65, 67, 74, 86, 92
74, 92
66, 84, 101
78
69
97
83, 90
68
83
64
69, 98
66, 100
97
83
91
64
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Right0
DR-MH30EU_00.book Page 65 Tuesday, June 29, 2004 5:41 PM
SYSTEM CONNECTIONS
Connecting To A Satellite Receiver
Simple Connections
This is an example of a simple connection if your TV has one
21-pin AV input (SCART) connector.
Connect the satellite receiver to the L-2 IN/DECODER connector,
then connect the L-1 IN/OUT connector to the TV’s connector.
NOTES:
● Set “L-2 SELECT” to “VIDEO” or “S-VIDEO”. (墌 pg. 61)
● You can use the Automatic Satellite Programme Recording function
(墌 pg. 48) with this connection.
● To record a programme via the satellite receiver, select L-2 mode by
pressing PR +/– so that “L-2” appears on the front display panel.
● For details, refer to the instruction manual of the satellite receiver.
Outdoor unit
Satellite cable
Aerial
65
Perfect Connections (Recommended)
This is an example of recommended connections if your TV
has two 21-pin AV input (SCART) connectors.
Connect the decoder to the satellite receiver’s connector if you
have a decoder, L-1 IN/OUT connector to TV’s connector, and L-2
IN/DECODER connector to the satellite receiver’s connector. Then
connect the satellite receiver and TV.
NOTES:
● Set “L-2 SELECT” to “VIDEO” or “S-VIDEO”. (墌 pg. 61)
● You can use the Automatic Satellite Programme Recording function
(墌 pg. 48) with this connection.
● To record a programme via the satellite receiver, select L-2 mode by
pressing PR +/– so that “L-2” appears on the front display panel.
● To receive a scrambled broadcast, descramble the signal with the
decoder connected to the satellite receiver.
● For details, refer to the instruction manual of the satellite receiver and
decoder.
Outdoor unit
TV aerial cable
Satellite cable
Satellite receiver
ANTENNA IN
EN
Aerial
TV aerial cable
Satellite receiver
ANTENNA OUT
ANTENNA IN
ANTENNA OUT
TV
Decoder
TV
IMPORTANT
When you set “L-2 SELECT” to “SAT VIDEO” or “SAT S-VIDEO”
(墌 pg. 61), it is possible to view a satellite broadcast with the TV
set to its AV mode even if the unit is turned off. When the unit is
in Stop mode or recording, press TV AV/VIDEO on the remote
control to turn off the VIDEO lamp on the unit.
● If you turn on the unit when the satellite receiver’s power is off,
nothing appears on the TV screen. In this case, turn on the satellite
receiver, or set the TV to its TV mode, or press TV AV/VIDEO on
the remote control to set the unit to the AV mode.
Page 65
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_09Editing.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 66 Tuesday, June 29, 2004 5:41 PM
66
EN
SYSTEM CONNECTIONS
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
These instructions enable you to connect your unit to a Dolby
Digital decoder or an amplifier with built-in DTS.
Dolby Digital Decoder or
amplifier with built-in DTS
To DIGITAL AUDIO input
Optical cable
(not provided)
When you can’t switch the audio channel of a bilingual
programme
When the unit is connected with a digital audio device using an
optional optical cable and “DIGITAL AUDIO OUT” is set to “DOLBY
DIGITAL/PCM”, it is not possible to switch the audio channel of a
bilingual programme recorded on a DVD-RAM or DVD-RW (VR
mode) disc. In this case, perform the following steps using the
remote control to switch “DIGITAL AUDIO OUT” from “DOLBY
DIGITAL/PCM” to “PCM ONLY”. (墌 pg. 29)
A Press SET UP to access the Main Menu screen.
B Press w e to select “DVD VIDEO SET UP”, then press t.
C Press w e to select “AUDIO OUTPUT”, then press t.
D Press rt to select “DIGITAL AUDIO OUT”, then press
ENTER.
E Press rt to select “PCM ONLY”, then press ENTER.
(墌 pg. 67)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel.
Connecting/Using A Decoder
Coaxial cable
(not provided)
The L-2 IN/DECODER connector can be used as an input
connector for an external decoder (descrambler). Simply connect a
decoder and you can enjoy a variety of programming that is
available through scrambled channels.
Decoder
DIGITAL OUT (COAXIAL)
TV aerial cable
TV
L-1 IN/OUT
DIGITAL OUT (OPTICAL)
Note for connection:
Remove the protection cap from the cable.
1 Connect the unit and a Dolby Digital decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
NOTES:
● For Dolby Digital sound, set “DIGITAL AUDIO OUT” to “DOLBY
DIGITAL/PCM”. (墌 pg. 67)
● For DTS sound, set “DIGITAL AUDIO OUT” to “STREAM/PCM”.
(墌 pg. 67)
L-2 IN/DECODER
RF cable (provided)
1 Set “L-2 SELECT” to “DECODER”. (墌 pg. 61)
2 Connect your unit’s L-2 IN/DECODER connector to the
decoder’s 21-pin SCART connector using a 21-pin SCART cable.
3 Perform the procedure as described in “When Receiving A
Scrambled Broadcast” (墌 pg. 72).
CAUTIONS:
● This unit has a dynamic range of more than 110 dB with regards to its
Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to the
speakers may damage them.
● Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do not
place the speakers adjacent to the TV set as this can adversely affect
the playback picture.
Page 66
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Right0
DR-MH30EU_00.book Page 67 Tuesday, June 29, 2004 5:41 PM
SUBSIDIARY SETTINGS
EN
67
* The boldface settings below indicate the settings at your purchase.
Mode Set
AUDIO OUTPUT
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
8 DIGITAL AUDIO OUT — DOLBY DIGITAL/PCM / STREAM/
PCM / PCM ONLY
Set to the appropriate mode according to the type of the device
connected to DIGITAL OUT connector.
CABLE/SAT
TV
DOLBY DIGITAL/PCM: Select this when you connect the digital
DVD
input connector of a Dolby Digital decoder or an amplifier with a
built-in Dolby Digital decoder.
STREAM/PCM: Select this when you connect the digital input
connector of an amplifier with a built-in DTS, Dolby Digital, or
MPEG multichannel decoder.
PCM ONLY: Select this when you connect the linear PCM digital
input of other audio equipment (amplifier, MD or DAT deck, etc.).
NOTES:
● This setting functions also when HDD is active.
● If you watch or play back a title which contains multiple audio
languages, select “PCM ONLY” in advance and choose main or sub
audio with AUDIO.
ENTER
rtwe
8 ANALOG AUDIO OUT — STEREO / DOLBY SURROUND
Select the appropriate setting to accommodate the unit to the
connected A/V equipment. This function takes effect when a
DVD VIDEO disc is played back.
STEREO: Select this when listening to conventional two-channel
SET UP
AUDIO
Various modes of this unit are categorized into menus nested in 2
levels shown in the following table. To change the settings of these
modes, find the desired mode in the menu (for details on each
menu, see pages 67 through 68), then follow the procedure below.
DVD VIDEO SET UP
HDD/DVD SET UP
FUNCTION SET UP
LANGUAGE SET (墌 pg. 21)
AUDIO OUTPUT (墌 pg. 67)
PARENTAL LOCK (墌 pg. 34)
DISC PLAY SET UP (墌 pg. 68)
HDD SET UP (墌 pg. 68)
DVD SET UP (墌 pg. 68)
DISC SET UP (墌 pg. 74, 75)
REC/PLAY SET UP (墌 pg. 68)
DISPLAY SET (墌 pg. 69)
VIDEO IN/OUT (墌 pg. 22, 61)
stereo audio with the unit’s AUDIO OUT connectors connected
to a stereo amplifier/receiver or TV set, or in case you want to
record the audio from a DVD VIDEO disc to a Mini Disc, etc.
DOLBY SURROUND: Select this when listening to multichannel
surround audio with the unit’s AUDIO OUT connectors
connected to an amplifier/receiver with a built-in surround
decoder or a surround decoder.
8 D. RANGE CONTROL — NORMAL / WIDE RANGE /
TV MODE
The dynamic range (the difference between the loudest sound and
the quietest one) can be compressed during playback of a
programme encoded in Dolby Digital format.
This function takes effect when a DVD VIDEO disc recorded in
Dolby Digital format is played back at low or middle volume.
NORMAL: Normally select this setting to activate this function.
WIDE RANGE: Select this to deactivate this function when you
enjoy wide dynamic range programme.
TV MODE: Select this when you hear the sound through the TV’s
speaker(s).
NOTES:
INITIAL SET UP
TUNER SET (墌 pg. 70)
CLOCK SET (墌 pg. 73)
● The procedure below shows how to set the desired option of the
“AUDIO REC” mode as an example.
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “FUNCTION SET UP”, then press t.
3 Press w e to select “REC/PLAY
DVD VIDEO SET UP HDD/DVD SET UP
SET UP”, then press t.
4 Press rt to select “AUDIO
REC”, then press ENTER.
5 Press rt to select the desired
option, then press ENTER.
6 Press SET UP to complete the
REC/PLAY SETUP
DISPLAY SET
XP MODE REC AUDIO
AUDIO REC
ENTER
EXIT
SELECT
VIDEO IN/OUT
DOLBY DIGITAL
8 OUTPUT LEVEL — STANDARD / LOW
You can lower the output level of analog audio to accommodate the
unit to the connected A/V equipment.
STANDARD: Normally select this setting.
LOW: The output level of analog audio is lowered.
OFF
INPUT COLOUR SYSTEM
SET UP
INITIAL SET UP
NICAM
DIRECT REC
JUMP TIME
FUNCTION SET UP
● This function takes no effect on programmes other than that recorded
in Dolby Digital format.
● This function dose not work when Simulated Surround Effect is
activated. (墌 pg. 32)
● The effect of “NORMAL” and “WIDE RANGE” may not be different
depending on discs.
PAL
15 MIN
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
setting.
Page 67
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Left+
DR-MH30EU_10Subsidiary.fm Page 68 Friday, July 2, 2004 2:19 PM
68 EN SUBSIDIARY SETTINGS
DISC PLAY SET UP
REC/PLAY SET UP
8 RESUME — OFF / ON / DISC RESUME
8 XP MODE REC AUDIO — DOLBY DIGITAL / LINEAR PCM
When this function is set to “ON” or “DISC RESUME”, you can use
the resume function. (墌 pg. 27)
You can select the audio format when you record a title in XP
mode. When this function is set to “LINEAR PCM”, you can obtain
a high-quality audio sound.
OFF: You cannot use the resume function.
ON: You can start playback from the resume point of the placed
disc.
DISC RESUME: The unit retains a memory of the resume points of
the last 30 discs played back, even though they have been ejected.
NOTE:
“DISC RESUME” setting works on DVD VIDEO, VCD, SVCD and
already finalised DVD-R/DVD-RW (video mode) discs. For other types
of discs, the function under “ON” setting will be applied even if
“RESUME” is set to “DISC RESUME”.
HDD SET UP
8 LIVE MEMORY — OFF / 30 MIN / 1 HR / 3 HR
When this function is set to “30 MIN”, “1 HR” or “3 HR”, you can
apply the selected time length to “Temporary recording for Live
Memory” (墌 pg. 41).
DVD SET UP
8 SAVE AS LIBRARY — OFF / ON
When this function is set to “ON”, the recording information is
automatically stored in the library. For details, refer to “Modify
Library Information” (墌 pg. 54).
8 CONTINUOUS PLAY — OFF / ON
When this function is set to “ON”, multiple titles on a disc are
played back continuously one after another.
8 VIDEO MODE RECORDING ASPECT — PRIORITIZE 4:3 /
PRIORITIZE 16:9
This is the setting for the aspect ratio used when you dub titles to
DVD discs in video mode. If the titles you want to dub are recorded
in both 16:9 and 4:3, you must select one aspect ratio.
PRIORITIZE 4:3: If you select “PRIORITIZE 4:3”, even a title
recorded in 16:9 is dubbed in 4:3.
PRIORITIZE 16:9: If you select “PRIORITIZE 16:9”, even a title
recorded in 4:3 is dubbed in 16:9.
8 VIDEO MODE RECORDING AUDIO — MAIN / SUB
DOLBY DIGITAL: To record in Dolby Digital format.
LINEAR PCM: To record in Linear PCM format.
8 AUDIO REC — NICAM / MONO
You can select the desired NICAM audio channel to be recorded
on a DVD-R/RW (Video mode) disc.
NICAM: To record the main and sub language of NICAM audio.
MONO: To record the standard (monaural) sound of NICAM audio.
NOTE:
This function works only for the NICAM bilingual programme.
8 DIRECT REC — OFF / ON
When this function is set to “ON”, you can easily start recording the
programme that you are watching on your TV. Press and hold 7
and press 4 on the remote control, or press 7 on the unit.
NOTES:
● When you use the Direct Rec function, be sure to use a TV offering
T-V LINK, etc. and connect a fully-wired 21-pin SCART cable
between the unit and the TV. (墌 pg. 17)
● If “DIRECT REC” is set to “OFF”, the 7 button functions as described
in “Basic Recording” (墌 pg. 35, 38).
● During Direct Rec, “– –” appears on the front display panel.
● If a programme is recorded with the Direct Rec, the station name will
not be registered in the library. “– – – –” will be displayed for the
station name.
● Even if there is no power supply for more than 60 minutes, the unit
keeps the setting.
8 INPUT COLOUR SYSTEM — PAL / SECAM
You can play back PAL discs, or record PAL and SECAM signals on
this unit. Select the appropriate colour system.
PAL: To record PAL signals.
SECAM: To record SECAM signals.
8 JUMP TIME — 15 MIN / 30 MIN / 1 HR
You can locate a scene ahead of or behind the currently viewed
one by jumping a selected time interval during playback (or Live
Memory Playback) or recording (or Live Memory Recording). For
details, refer to “Jump Search” (墌 pg. 43).
This is the setting for the audio channel to be selected when
dubbing titles to DVD discs in video mode. Select either one of the
two settings if the titles to be dubbed have two audio channels.
MAIN: Select this to dub the main channel.
SUB: Select this to dub the sub channel.
8 MP3 & WMA / JPEG — MP3 & WMA / JPEG
You can select files to play back, when both MP3/WMA files and
JPEG files are recorded on a disc.
MP3 & WMA: Select this to play back MP3/WMA files.
JPEG: Select this to play back JPEG files.
Page 68
Friday, 2 July 2004 14:18
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 69 Tuesday, June 29, 2004 5:41 PM
SUBSIDIARY SETTINGS
DISPLAY SET
8 SUPERIMPOSE — OFF / AUTO
When this function is set to “AUTO”, various operational indicators
appear on the TV screen. Messages appear in the selected
language. (墌 pg. 21)
OFF: To turn off superimposed indications.
AUTO: To superimpose operational indications for approximately
five seconds just after the corresponding operation.
NOTES:
● Even when “SUPERIMPOSE” is set to “OFF”, you can display the
various operational indicators by pressing ON SCREEN. To clear the
operational indicators, press ON SCREEN again.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting. (墌 pg. 60)
● When you select “AUTO”, during playback, the operation mode
indicators may be disturbed depending on the type of disc being used.
8 BLUE BACK — ON / OFF
69
Scan Mode Set
If you connect the unit and TV with Component Video Connection
(墌 pg. 17), you can select the scan mode from two modes:
Interlaced scan mode which is used in the conventional TV system,
and Progressive scan mode which enables reproduction of higherquality images.
8 Interlaced scan
In the conventional video system, a picture is shown on the display
monitor in two halves. The Interlaced scan system places lines of
the second half of the picture in-between lines of the first half of the
picture.
8 Progressive scan
Progressive scan displays all the horizontal lines of a picture at one
time, as a single frame. This system can convert the interlaced
video from DVD into progressive format for connection to a
progressive display. It dramatically increases the vertical resolution.
When this function is set to “ON”, the TV screen becomes all blue
when receiving a channel not in use.
NOTE:
ATTENTION:
When you want to receive an unstable channel with poor signals, set
this function to “OFF”.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
8 DIMMER — BRIGHT / DIMMED1 / DIMMED2 / OFF
EN
Your TV needs to be compatible with PAL Progressive.
You can change the brightness of the front display panel.
CABLE/SAT
BRIGHT: Normally select this.
DIMMED1/DIMMED2: To change the brightness level. (Blue lamp
TV
DVD
on the front display panel becomes dimmer.)
OFF: To dim the front display panel. (Blue lamp on the front display
panel is turned off.)
8 POWER SAVE — OFF / ON
When this function is set to “ON”, you can reduce the power
consumption while the unit is turned off.
NOTES:
● During Power Save mode —
— the front display panel will be turned off.
— the Just Clock function (墌 pg. 73) does not work.
● Power Save does not work when —
— the unit is in the Timer mode.
— the unit’s power is turned off after timer-recording or Instant Timer
Recording.
— the Automatic Satellite Programme Recording mode is engaged.
(墌 pg. 48)
— “L-2 SELECT” is set to “DECODER”, “SAT VIDEO” or “SAT S-VIDEO”.
(墌 pg. 61)
● It takes some time for the unit to complete initialisation after you turn
on the unit power, with “WAKE UP” blinking on the front display panel.
8 ON SCREEN LANGUAGE
This unit offers you the choice to view on-screen messages in 10
different languages. Though Auto Set Up selects the language
automatically (墌 pg. 20), you can change the language setting
manually as required.
For details, refer to “On-screen Language Set” (墌 pg. 21).
PROGRESSIVE SCAN
1 Press PROGRESSIVE SCAN for 3 or more seconds.
● Video output indicator ( ) lights on the front display panel if
Progressive scan mode has been established. (墌 pg. 12)
● Each press of PROGRESSIVE SCAN for 3 or more seconds
switches the scan mode.
NOTES:
● When the progressive mode is set, be sure to set “L-1 OUTPUT” to
“COMPONENT”. (墌 pg. 61) Progressive scan is output only from
COMPONENT VIDEO OUT connector.
● Interlaced scan mode is the setting at your purchase.
● Interlaced scan mode might be suitable depending on video material.
● Scan mode cannot be set while menu screen is displayed.
● When Progressive scan mode is engaged, no video signal is output
from S-VIDEO OUT connector and L-1 IN/OUT connector.
Page 69
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 70 Tuesday, June 29, 2004 5:41 PM
70
EN
SUBSIDIARY SETTINGS
Tuner Set
SHOWVIEW System Setup
TM
IMPORTANT:
Normally, Auto Set Up (墌 pg. 18), Preset Download (墌 pg. 19) or
Auto Channel Set (墌 pg. 70) sets the Guide Program numbers
automatically. You need to set the Guide Program numbers manually
only in the following cases.
● When timer-programming with the SHOWVIEW system, the channel
position, where the station you wish to record is received on your
unit, is not selected,
Your unit needs to memorise all necessary stations in channel
positions in order to record TV programmes. Auto Channel Set
automatically assigns all receivable stations in your area to call
them up by using the PR +/– buttons without going through any
vacant channels.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
OR
when you add a channel after Auto Set Up, Preset Download or Auto
Channel Set has taken place,
—Set the Guide Program number for that station manually.
CABLE/SAT
TV
DVD
● When you wish to timer-record a satellite programme with the
SHOWVIEW system,
—Set the Guide Program numbers for all satellite broadcasts received
on your satellite receiver.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
ENTER
Guide Program Number Set
rtwe
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “INITIAL SET UP”, then press t.
3 Press w e to select “TUNER
SET”, then press t.
DVD VIDEO SET UP HDD/DVD SET UP
TUNER SET
FUNCTION SET UP
4 Press rt w e to select “GUIDE
PROG SET”, then press ENTER.
AUTO CH SET
MANUAL CH SET
SAT CONTROL SET
GUIDE PROG SET
11
5 Press rt to select “GUIDE
PROG”, then press ENTER.
6 Press rt to select the Guide
SET UP
ENTER
EXIT
SELECT
11
12
13
12
SET UP
13
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
INITIAL SET UP > GUIDE PROG SET
GUIDE PROG
TV PROG
1
YLE2 1
Program number for the desired
station as shown in the TV listings.
Then press ENTER.
● To change the Guide Program
number in 10 increments, press and
hold rt.
INITIAL SET UP
CLOCK SET
RETURN
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
7 Press rt to select “TV PROG”, then press ENTER. Press rt
to select the number of the unit’s channel position on which the
Guide Program number’s broadcast is received by the unit or the
satellite receiver. Then press ENTER.
● Pressing AUX changes “TV PROG” to “SAT”.
● To timer-record a satellite programme with the SHOWVIEW system,
you need to install the provided Satellite Controller and perform the
procedure described in “Satellite Receiver Control Setting”
(墌 pg. 23).
● Repeat steps 5 – 7 as necessary.
8 Press SET UP to complete the setting.
Guide Program Number
“Guide Program (GUIDE PROG) number” refers to the assigned
TV station numbers, according to broadcast area, for the
SHOWVIEW timer recording. The Guide Program Numbers can
be found in most TV listings.
Page 70
IMPORTANT:
Perform the following steps only if —
— Auto Channel Set has not been set correctly by Auto Set Up
or by Preset Download. (墌 pg. 18, 19)
— you have moved to a different area or if a new station starts
broadcasting in your area.
Auto Channel Set
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “INITIAL SET UP”, then press t.
3 Press w e to select “TUNER SET”, then press t.
4 Press rt w e to select
DVD VIDEO SET UP HDD/DVD SET UP
“AUTO CH SET”, then press
ENTER.
TUNER SET
FUNCTION SET UP
INITIAL SET UP
CLOCK SET
AUTO CH SET
MANUAL CH SET
SAT CONTROL SET
GUIDE PROG SET
5 Press rt w e to select your
country’s name, then press
ENTER.
6 Press rt w e to select the
language of your choice.
11
SET UP
ENTER
EXIT
SELECT
12
13
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
7 Press ENTER twice.
● When you have connected the unit
to a TV offering T-V Link via a
fully-wired 21-pin SCART cable
(墌 pg. 17), the unit automatically
performs the Preset Download
and the T-V LINK screen will
appear. (墌 pg. 19)
● The Auto Set screen appears, and
remains on screen while the unit
searches for receivable stations.
INITIAL SET UP > AUTO SET
AUTO SET
PLEASE WAIT...
CANCEL
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
DR-MH30EU_00.book Page 71 Tuesday, June 29, 2004 5:41 PM
Masterpage:Right+
SUBSIDIARY SETTINGS
8 View the Confirmation screen.
“AUTO SET COMPLETED” or “SCAN COMPLETED” is displayed
on the TV screen.
9 Press SET UP to complete the setting.
● Using the Confirmation screen, you can skip or add channel
positions, enter station names and perform other operations. Refer to
pages 71 – 72 for the procedures.
● Depending on reception conditions, the stations may not be stored in
order, and the station names may not be stored correctly.
● For information on scrambled broadcasts, refer to “When Receiving A
Scrambled Broadcast” (墌 pg. 72).
IMPORTANT:
● In certain reception conditions, station names may not be stored
correctly, and Auto Guide Program Number Set may not work
properly. When the Guide Program numbers are not set properly,
the programme that you do not intended to record will be timerrecorded by the SHOWVIEW system of the unit. When programming
the timer using the SHOWVIEW system, be sure to check the
desired channel is selected correctly. (墌 pg. 44, “ShowViewTM
Timer Programming”)
● Your unit memorises all receivable stations even if reception of
some of them is poor. You can delete those stations with an
unacceptable picture from the list. (墌 pg. 72, “Delete A Channel”)
71
Manual Channel Set
Store channels that were not stored during Auto Set Up
(墌 pg. 18), Preset Download (墌 pg. 19) or Auto Channel Set
(墌 pg. 70).
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “INITIAL SET UP”, then press t.
3 Press w e to select “TUNER SET”, then press t.
4 Press rt w e to select “MANUAL CH SET”, then press
ENTER. The Manual Channel Set screen appears.
5 Press w e to select “EDIT”, then press ENTER.
6 Press rt w e to select a
(Example) To store in position 12.
blank position in which you want to
store a channel, then press
ENTER. The Confirmation screen
appears.
INITIAL SET UP > MANUAL CH SET
7 Press rt to select “BAND”,
then press ENTER.
PR
CH
ID
CH
01
C01
----
07
----
02
02
CTEA
08
----
03
05
1000
09
----
04
C79
3SAT
10
----
05
01
9LIV
11
----
06
04
AB3
12
----
<
>
MOVE
CH
ID
EDIT
RETURN
The programme currently
received on the selected channel
position appears behind the
confirmation screen.
NOTES:
● Fine tuning is performed automatically during Auto Channel Set. If
you want to perform tuning manually, refer to “Fine-Tuning Channels
Already Stored” (墌 pg. 72).
● If you perform Auto Channel Set when the aerial cable is not
connected properly, “SCAN COMPLETED –NO SIGNAL–” appears
on the TV screen in step 8. In such a case, make sure of the aerial
connection and press ENTER; Auto Channel Set will start again.
● If no sound accompanies the picture or the audio sounds unnatural
on some channels that have been stored by Auto Set Up, the TV
system setting for those channels may be incorrect. Select the
appropriate TV system for those channels. (墌 pg. 72,
“INFORMATION”)
EN
8 Press rt to change the band
between CH (regular) and CC
(cable), then press ENTER.
9 Press rt to select “CH”, then
press ENTER.
INITIAL SET UP > MANUAL CH SET
BAND
CH
CH
2
ID
----
FINE
DECODER
OFF
10 Press rt to input the
channel number you want to store.
RETURN
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
● To enter the registered station
name (墌 pg. 85), press rt to
select “ID”, then press ENTER. Press rt.
● For fine tuning adjustment, press rt to select “FINE”, then press
ENTER. Press rt to perform fine-tuning.
● When storing a channel that sends scrambled broadcasts, press rt
to select “DECODER”, then press ENTER. Press rt to set
“DECODER” to “ON” (“OFF” is the default setting).
● When “L-2 SELECT” is set to “VIDEO”, “S-VIDEO”, “SAT VIDEO” or
“SAT S-VIDEO”, the “DECODER” setting cannot be changed.
(墌 pg. 61)
11 Press ENTER to enter new channel information. The
Confirmation screen appears.
12 Press SET UP to close the Confirmation screen.
● To change positions, see “Change Station Channel Position”
(墌 pg. 72).
● If you wish to set station names other than the ones registered in your
unit, see “Set Stations (B)” (墌 pg. 72).
ATTENTION:
Guide Program numbers are not set when channels are stored
manually. (墌 pg. 70, “ShowViewTM System Setup”)
Page 71
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 72 Tuesday, June 29, 2004 5:41 PM
72 EN SUBSIDIARY SETTINGS
Delete A Channel
Set Stations (A)
1 Perform steps 1 – 5 of “Manual Channel Set” (墌 pg. 71).
2 Press rt w e to select the channel you want to delete.
3 Press & to delete a channel. The channel next to the cancelled
one moves up one line.
● Repeat steps 2 – 3 as necessary.
1 Perform steps 1 – 4 of “Manual Channel Set” (墌 pg. 71).
2 Press w e to select “MOVE”, then press ENTER.
3 Press rt w e to select the channel you want to move, then
press ENTER.
4 Press rt w e to select the new channel position, then press
ENTER.
Example: If you moved the station in position 4 to position 2, the
stations originally in positions 2 and 3 each move down
one space.
CH
ID
CH
ID
PR
CH
ID
CH
C01
----
07
----
01
C01
----
07
----
02
C79
CH
ID
02
CTEA
08
----
3SAT
08
----
03
05
1000
09
----
03
02
CTEA
09
----
04
C79
3SAT
10
----
04
05
1000
10
05
01
9LIV
11
----
05
01
9LIV
11
----
06
04
AB3
12
----
06
04
AB3
12
----
<
>
MOVE
EDIT
RETURN
<
>
MOVE
5 Press ENTER to select the desired ID, then press ENTER again
to select “OK”.
6 Press RETURN to return to the Manual Channel Set screen.
● Repeat steps 2 – 5 as necessary.
7 Press SET UP to close the Confirmation screen.
Set Stations (B)
Set station names other than the ones registered in your unit.
1 Perform steps 1 – 5 of “Manual Channel Set” (墌 pg. 71).
2 Press rt w e to select the channel you want to modify, then
press ENTER. The Confirmation screen appears.
INITIAL SET UP > MANUAL CH SET
PR
01
02
press ENTER. The Confirmation screen appears.
station names (ID) (墌 pg. 85) appear as you press rt.
Change Station Channel Position
CH
1 Perform steps 1 – 5 of “Manual Channel Set” (墌 pg. 71).
2 Press rt w e to select the channel you want to modify, then
3 Press rt to select “ID”, then press ENTER.
4 Move the arrow to the left ID selection column. Registered
4 Press SET UP to close the Confirmation screen.
INITIAL SET UP > MANUAL CH SET
Set station names that are registered in your unit.
----
EDIT
RETURN
● Repeat steps 3 – 4 as necessary.
5 Press SET UP to close the Confirmation screen.
3 Press rt to select “ID”, then press ENTER.
4 Press rt w e to select the desired characters (A–Z, 0–9, –, f,
+, I (space)), then press ENTER.
● Enter the remaining characters the same way (maximum of 4).
5 After entering all characters, press rt w e to select “OK”, then
press ENTER.
6 Press RETURN to return to the Manual Channel Set screen.
● Repeat steps 2 – 5 as necessary.
When Receiving A Scrambled Broadcast
7 Press SET UP to close the Confirmation screen.
1 Set “L-2 SELECT” to “DECODER”. (墌 pg. 61)
2 Perform steps 1 – 5 of “Manual Channel Set” (墌 pg. 71).
3 Press rt w e to select the channel position broadcasting
Fine-Tuning Channels Already Stored
scrambled programmes, then press ENTER. The Confirmation
screen appears.
4 Press rt to select “DECODER”, then press ENTER.
5 Press rt to set “DECODER” to “ON”, then press ENTER.
6 Press RETURN to return to the Manual Channel Set screen.
● Repeat steps 3 – 5 as necessary.
7 Press SET UP to close the Confirmation screen.
INFORMATION
If you live in Eastern Europe, “TV SYSTEM” setting appears
instead of “DECODER” setting on the Manual Channel Set
screen. When you can see the picture but can hear no audio,
select appropriate TV system (D/K or B/G). Normally, TV
programmes are broadcast as follows.
For Eastern Europe : D/K
For Western Europe : B/G
A Select a country in Eastern Europe in step 5 of “Auto
Channel Set” (墌 pg. 70).
B Press rt to select “TV SYSTEM” in step 7 of “Manual
Channel Set” (墌 pg. 71).
C Press rt to select appropriate TV System (D/K or B/G).
Page 72
NOTE:
The characters available for the station name (ID) are A–Z, 0–9, –,
f, +, I (space) (maximum of 4).
1 Perform steps 1 – 5 of “Manual Channel Set” (墌 pg. 71).
2 Press rt w e to select the channel you want to fine-tune, then
press ENTER. The Confirmation screen appears.
3 Press rt to select “FINE”, then press ENTER.
4 Press rt until the picture appears in its best quality, then press
ENTER.
● Repeat steps 2 – 4 as necessary.
5 Press RETURN to return to the Manual Channel Set screen.
6 Press SET UP to close the Confirmation screen.
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 73 Tuesday, June 29, 2004 5:41 PM
SUBSIDIARY SETTINGS
EN
73
7 Press SET UP to start the clock operation.
Clock Set
NOTES:
IMPORTANT:
If you performed Auto Set Up (墌 pg. 18) or Preset Download
(墌 pg. 19), without ever having set the clock previously, the
unit’s built-in clock is also set automatically.
Perform the following steps only if —
— Auto Clock Set has not been performed correctly by Auto Set
Up or Preset Download.
OR
— you want to change Just Clock setting. (墌 “Just Clock” in the
right column)
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
— the unit’s power is on.
— the unit is in the Timer mode.
— a difference of more than 3 minutes exists between the built-in
clock’s time and the actual time.
— the unit is in the Automatic Satellite Programme Recording
mode. (墌 pg. 48)
— the unit is in the Power Save mode. (墌 pg. 69)
— “L-2 SELECT” is set to “SAT VIDEO” or “SAT S-VIDEO”.
(墌 pg. 61)
● If Just Clock is set to “ON”, the unit’s clock is automatically adjusted
at the start/end of Summer Time.
● Just Clock may not function properly depending on the reception
condition.
Just Clock
The Just Clock function provides accurate time keeping through
automatic adjustments at regular intervals, by reading data from a
PDC signal.
The Just Clock option can be set to “ON” or “OFF” at the Clock Set
screen (the default setting is “OFF”).
CABLE/SAT
TV
● Just Clock (when set to “ON”) adjusts the unit’s built-in clock every
hour, except for 23:00, 0:00, 1:00 and 2:00.
● Just Clock is not effective when:
DVD
IMPORTANT:
If you turn off Just Clock, the accuracy of your unit’s built-in clock may
be reduced, which could adversely effect timer recording. We
recommend you to keep Just Clock on. In cases where the clock setting
data from a PDC signal is incorrect, however, you are advised to keep
Just Clock set to “OFF”.
ENTER
rtwe
SET UP
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “INITIAL SET UP”, then press t.
3 Press w e to select “CLOCK
SET”, then press t.
NOTE:
When you have selected
MAGYARORSZÁG, ČESKÁ
REPUBLIKA, POLSKA or OTHER
EASTERN for the country setting
(墌 pg. 18), you cannot use Just
Clock function. Skip steps 5 and 6.
DVD VIDEO SET UP HDD/DVD SET UP
TUNER SET
INITIAL SET UP
FUNCTION SET UP
CLOCK SET
YEAR
2004
DATE
01. 01(THU)
TIME
--:--
JUST CLOCK
OFF
TV PROGRAMME
SET UP
ENTER
EXIT
SELECT
1
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
4 Press rt to select “YEAR”, then press ENTER. Press rt to
set the year, then press ENTER.
● Repeat the same procedure to set the date and time.
● When you set the date, press and hold rt to change the date by 15
days.
● When you set the time, press and hold rt to change the time by 30
minutes.
5 Press rt to select “JUST CLOCK”, then press ENTER. Press
rt to set to the desired mode, then press ENTER.
● The default setting is “OFF”.
● For the Just clock function, refer to “Just Clock” on the right column.
● If you set to “OFF”, you can disregard the next step as you won’t be
able to receive regular clock adjustments.
6 Press rt to select “TV PROGRAMME”, then press ENTER.
Press rt to set the channel position to the number representing
the station transmitting clock setting data, then press ENTER.
● The unit is preset to receive clock setting and adjustment data from
channel position 1.
Page 73
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 74 Tuesday, June 29, 2004 5:41 PM
74
EN
SUBSIDIARY SETTINGS
Format A Disc (DVD Deck Only)
Some DVD-RAM/RW discs are unformatted.
Format the disc when you use an unformatted disc or you want to
delete all recordings and data on the disc.
ATTENTION:
Format A DVD-RAM Disc
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “HDD/DVD SET UP”, then press t.
3 Press w e to select “DISC SET
UP”, then press t.
DVD VIDEO SET UP HDD/DVD SET UP
HDD SET UP
4 Press rt w e to select
FUNCTION SET UP
DVD SET UP
DISC SET UP
FINALIZE
CANC. FINALIS.
INITIAL SET UP
Video
“FORMAT”, then press ENTER.
Press w e to select “OK”, then
press ENTER.
Vid
eo
FORMAT
● When a disc is formatted, all recordings and data are erased. It is
impossible to restore them.
● Never turn off the unit or disconnect the mains power cord while
“NOW FORMATTING...” is displayed on the TV screen.
5 Press w e to select “OK”, then
press ENTER.
●
●
●
●
1 Perform steps 1 to 3 of “Format A DVD-RAM Disc” on the above
before continuing.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Load a DVD-RAM/RW disc to format.
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Format A DVD-RW Disc
2 Press rt w e to select “FORMAT”, then press ENTER. Press
CABLE/SAT
TV
DVD
w e to choose “VR MODE” or “VIDEO MODE”, then press ENTER
when “DISC WILL BE FORMATTED” appears on the TV screen.
“VR MODE”:
To be chosen when you want to record, erase, or
edit data on the disc repeatedly.
“VIDEO MODE”: To be chosen when you want to erase all the data
on the disc once played back to record new data,
or play back the disc on other DVD players.
3 Press w e to select “OK”, then press ENTER.
NOTES:
ENTER
rtwe
● It is impossible to format Version 1.0 DVD-RW discs in Video mode.
● It is impossible to format DVD-R discs.
● All the titles on a disc will be deleted once the disc is formatted even if
they are protected titles. (墌 pg. 51)
SET UP
Page 74
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
DR-MH30EU_00.book Page 75 Tuesday, June 29, 2004 5:41 PM
Masterpage:Right+
SUBSIDIARY SETTINGS
Finalise A Disc (DVD Deck Only)
Finalising DVD-R/RW discs recorded on this unit makes it possible
for the discs to be played back on other DVD players. DVD-RW
discs are finalised in the mode that the discs were formatted,
enabling playback on compatible DVD players.
Title names input in the Library Database Navigation are
registered as title names in the DVD menu. (墌 pg. 50)
●
●
●
●
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Load a DVD-R/RW disc to finalise.
EN
75
Finalise A DVD-R/RW Disc
1 Perform steps 1 to 3 of “Format A DVD-RAM Disc” (墌 pg. 74)
before continuing.
2 Press rt w e to select “FINALIZE”, then press ENTER.
Press w e to select “OK”, then press ENTER.
3 Press w e to select “OK”, then press ENTER.
4 Press SET UP to return to the normal screen.
● Menu screen is cleared.
● Once a DVD-R/RW (Video mode) disc has been finalised, the
displays for original and play list do not appear. Only display for
library appears.
● Once a DVD-RW (VR mode) disc has been finalised, it can be played
on DVD players compatible with VR mode.
Cancel The Finalisation Of A DVD-RW Disc
CABLE/SAT
TV
DVD
1 Load a DVD-RW disc to cancel the disc finalisation, and perform
steps 1 to 3 of “Format A DVD-RAM Disc” (墌 pg. 74) before
continuing.
2 Press rt w e to select “CANC. FINALIZ.”, then press ENTER.
3 Press w e to select “OK”, then press ENTER.
4 Press SET UP to return to the normal screen.
● When the disc finalisation is cancelled, the mode in which the disc
was formatted is restored, making the disc recordable. (墌 pg. 7, 74)
ENTER
rtwe
SET UP
Before finalising
●
●
●
●
●
It is possible to record on a blank space.
It is possible to enter title names. (墌 pg. 50)
It is possible to delete titles. (墌 pg. 51)
It is impossible to overwrite recorded areas of DVD-R discs.
Available recording capacity does not increase even if a recorded title
is deleted from a DVD-R disc.
● It is impossible to record or edit DVD-R/RW discs recorded on other
devices even if they have not been finalised.
After finalising (For DVD-R/RW (Video mode) discs)
● Video and audio that have been recorded by then are recorded in
conformity to the DVD Video standard, enabling you to play back the
discs as DVD VIDEO discs.
● Although DVD-R/RW discs finalised on this unit become playable on
DVD players compatible with DVD-R/RW discs, some discs still may
not play, for which JVC cannot take responsibility.
● Marked points marked before finalising will be deleted, and titles will
be divided automatically into “chapters” approximately every 5
minutes. (墌 pg. 27)
● Depending on the DVD players and DVD-R/RW discs used, and on
the conditions of recording, it may not be possible to play back the
discs. In this case, play back the discs on this unit.
● Additional recordings become impossible.
Page 75
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
DR-MH30EU_00.book Page 76 Tuesday, June 29, 2004 5:41 PM
76
EN
Masterpage:Left+
SUBSIDIARY SETTINGS
Help Function
Tray Lock (DVD Deck Only)
Use this function if you encounter problems while operating this
unit.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
You can lock the disc tray to prohibit the unwanted disc ejection by
children.
● Turn off the unit.
x
CABLE/SAT
TV
DVD
8
To lock tray
While the unit is turned off, press and hold 8, then press x on the
unit. “LOCKED” appears on the front display panel and the disc
tray is locked.
rt
ENTER
2
PREVIOUS
To unlock tray
While the unit is turned off, press and hold 8, then press x on the
unit. “UNLOCK” appears on the front display panel.
?
1 Press ? to access the help screen.
● An INDEX screen that contains the most common needed topics
(headings) relating to the current status appears. Topics with the
icon refer to HDD deck operations and with the
icon refer to
those for the DVD deck.
2 Press rt to search for the item that describes the solution to
your problem, then press ENTER.
● The selected help page appears.
● You can also browse help pages by pressing rt.
● To return to a previous page, press RETURN.
3 Press ? to return to the normal screen.
NOTE:
You cannot perform playback, recording, timer recording, or other
normal operations while accessing the help screen.
Page 76
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
DR-MH30EU_00.book Page 77 Tuesday, June 29, 2004 5:41 PM
Masterpage:Right0
TROUBLESHOOTING
Before requesting service for a problem, use this chart and see if
you can solve the trouble yourself. Small problems are often easily
solved, and this can save you the trouble of sending your unit off
for repair.
Initialising (DVD Deck Only)
Malfunction occurs on the unit.
]Press 1 to turn off the unit, press and hold 1, then press 8
for two seconds or more.
General
No power is supplied to the unit.
● The AC power plug is disconnected from the mains outlet.
]Connect the AC power plug to the mains outlet securely.
(墌 pg. 17)
The remote control does not work properly.
]Remove the batteries, wait for 5 minutes or more, then load the
butteries again.
● The setting of the remote control code is inappropriate.
]Set the same remote control code (1, 2, 3, or 4) on both the unit
and the remote control. (墌 pg. 63)
● The batteries are discharged.
]Replace the dead batteries with new ones.
Dubbing from the external equipment is not possible.
● The source (another video recorder, camcorder) has not been
properly connected.
]Confirm that the source is properly connected.
● All necessary power switches have not been turned on.
]Confirm that all units’ power switches are turned on.
● The setting of the input channel position is inappropriate.
]Select the input channel position (“F-1”, “L-1”, or “L-2”) that
corresponds to the input terminal connected to the external
equipment. (墌 pg. 60)
The on-screen display superimposed on the programme played
back/received on this unit is recorded when you dub the
programme to an external recording equipment.
]Set “SUPERIMPOSE” to “OFF”. (墌 pg. 69)
77
Playback (DVD Deck)
The DVD deck cannot be operated.
● The DVD deck is not selected.
]Press DVD so that the DVD lamp lights up on the unit.
Images do not appear on the TV screen.
● The TV receiver’s channel selector is not set to the AV mode.
]Set the TV to its AV mode.
● When interlace scanned programme is played back, progressive
scan mode is selected.
]Press and hold PROGRESSIVE SCAN until
disappears from
the front display panel. (墌 pg. 69)
Playback dose not start or stop immediately after playback is
started by pressing .
On the front display panel, “NO DISC” appears.
● The disc is loaded upside down.
]Place the disc on the disc tray with the playback surface facing
down. (墌 pg. 8)
● A disc not being compatible with the unit is loaded.
]Load a playable disc on the unit. (墌 pg. 5)
● A dirty disc is loaded.
]Clean the disc. (墌 pg. 9)
● Defective disc is loaded.
]Replace the warped or scratched disc with a normal one.
Images are blurred or distorted when you start High-Speed
Search.
]Images are blurred or distorted at the point where the playback
speed changes and this is not a malfunction of the unit.
Playback does not start.
]Playback does not start for approximately 30 seconds after
recording is stopped and this is not a malfunction of the unit.
Playback does not start when you select a title or a chapter.
● The Parental Lock is engaged and the disc is rated higher than
the set level.
]Release the Parental Lock temporarily or change the set level.
(墌 pg. 34)
The unit does not operate.
Playback (HDD Deck)
● There are cases when the operation is prohibited on the disc.
The HDD deck cannot be operated.
● Lightning or static electricity may cause malfunction of the unit.
]Press 1 to turn the power off, then press the button again to
turn the power on.
● The HDD deck is not selected.
]Press HDD so that the HDD lamp lights up on the unit.
Page 77
EN
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
DR-MH30EU_00.book Page 78 Tuesday, June 29, 2004 5:41 PM
78 EN TROUBLESHOOTING
Recording (DVD Deck)
Masterpage:Left+
Timer Recording
The desired programme cannot be recorded.
Timer programming cannot be made.
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
(墌 pg. 70)
● Date and time is not correct.
]Set date and time correctly. (墌 pg. 73)
● Timer recording is in progress.
]Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
Recording cannot be made.
● No disc or a disc not being compatible with the unit is loaded.
]Load a recordable disc on the unit. (墌 pg. 5)
● The disc loaded is not formatted.
]Format the disc. (墌 pg. 74)
● A finalised DVD-R disc is loaded.
]Recording cannot be made on finalised discs. Load a recordable
disc on the unit.
● The disc is full or does not have enough space for the title to be
recorded.
]Clear unnecessary titles on the disc or load a blank disc.
(墌 pg. 51)
● The DVD-RAM disc loaded has had its protect tab slid to the
protect position.
]Release the protect tab. (墌 pg. 8)
Recording (HDD Deck)
Timer programming recording does not start.
● Date and time is not correct.
]Set date and time correctly. (墌 pg. 73)
SHOWVIEW Timer Programming cannot be made.
● Date and time set on the unit is not correct.
]Set date and time correctly. (墌 pg. 73)
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
(墌 pg. 70)
The SHOWVIEW system does not timer-record properly.
● The unit’s channel positions have been set incorrectly.
]Refer to “ShowViewTM System Setup” (墌 pg. 70) and reperform the procedure.
TV broadcasts cannot be recorded.
Automatic Satellite Programme Recording does not start.
● “L-1”, “L-2” or “F-1” has been selected as the input mode.
]Set to the desired channel.
● The satellite receiver is not connected properly to this unit.
]Connect the satellite receiver to the L-2 IN/DECODER
connector properly. (墌 pg. 48)
Camcorder recording is not possible.
● The camcorder has not been properly connected.
]Confirm that the camcorder is properly connected.
● The input mode is not correct.
]Set the input mode to “F-1”. (墌 pg. 59)
On the front display panel, “– –:– –” appears.
● Power failure occurred.
]Set date and time correctly. (墌 pg. 73)
“PROGRAMME FULL” appears on the TV screen during timer
programming.
● 32 programmes have already been timer programmed.
]Clear unnecessary programmes on the unit, then try timer
programming again. (墌 pg. 47)
The disc space does not increase when recorded titles are
cleared.
● The PC’s data recorded on a DVD-RAM drive cannot be cleared
on this unit.
]Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (墌 pg. 9, 74)
Page 78
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
DR-MH30EU_00.book Page 79 Tuesday, June 29, 2004 5:41 PM
Masterpage:Right+
TROUBLESHOOTING
EN
Other Problems
On-screen Message
The image of the TV broadcast appears distorted on the TV
screen.
DISC NOT REGISTERED IN THE LIBRARY
REGISTER DISC?
For basic/S-video connection
]Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator ( ) lights off on the front display panel.
● A disc that is not registered in the library has been inserted.
Register the disc as necessary. (墌 pg. 54)
For component video connection
]Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator ( ) lights up on the front display panel.
Whistling or howling is heard from the TV during camcorder
recording.
● The camcorder’s microphone is too close to the TV.
]Position the camcorder so its microphone is away from the TV.
● The TV’s volume is too high.
]Turn the TV’s volume down.
When scanning channels, some of them are skipped over.
● Those channels have been designated to be skipped.
]If you need the skipped channels, restore them. (墌 pg. 70)
The channel cannot be changed.
● Recording or Live Memory recording* is in progress.
]Press 9 to pause the recording, change channels, then press 4
to resume recording.
* HDD deck only
Channel settings that were made manually seem to have
changed or disappeared.
● After the manual settings were made, Auto Channel Set was
performed.
]Perform “Clock Set” (墌 pg. 73).
Page 79
79
INSERT DISC XXXX
● Appears when a title that has been selected in the library is not
contained in the loaded disc.
CAN NOT RECORD OR MAKE PLAY LIST
DELETE UNWANTED TITLES
● Recording and/or editing cannot be performed.
● The number of titles exceeds 99.
● The number of play lists exceeds 999.
SET CLOCK BEFORE TIMER PROGRAMMING
● To set the timer programme, the clock must be set in advance.
(墌 pg. 73)
PROGRAMME FULL
DELETE UNWANTED TIMER PROGRAMMES
● You can programme this unit to timer-record as many as 32
programmes. To programme more, you need to cancel a timer
programme already set. (墌 pg. 47)
DISC NOT LOADED
● Operation has been attempted when a disc is not loaded, or
loaded upside down. (墌 pg. 8)
DISC NOT RECORDABLE
INSERT RECORDABLE DISC
● When a playback-only disc or a finalised disc is loaded, 7 has
been pressed. (墌 pg. 5)
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
DR-MH30EU_00.book Page 80 Tuesday, June 29, 2004 5:41 PM
80
EN
Masterpage:Left+
TROUBLESHOOTING
SHOWVIEW NO. ERROR
CONFIRM SHOWVIEW NO. THEN RETRY
● An invalid SHOWVIEW number has been input. (墌 pg. 44)
PRESS [STOP] AGAIN TO STOP RECORDING
● During Live Memory playback, 8 has been pressed. (墌 pg. 42)
TIMER RECORDING COMPLETED
GUIDE PROGRAM IS NOT SET
SET GUIDE PROGRAM THEN RETRY
● Timer recording has finished during Live Memory playback.
● To set the timer programme using the SHOWVIEW system, the
Guide Program number must be set in advance. (墌 pg. 70)
PLAYBACK WILL STOP
THEN TIMER RECORDING WILL START
CAN NOT SET SHOWVIEW TIMER PROGRAMMING DURING
TIMER RECORDING OR INSTANT TIMER RECORDING
● Timer recording finished during Live Memory playback, then the
next timer recording is about to begin while playback continues.
● Appears when you tried to input a SHOWVIEW number during
timer recording or instant timer recording.
COPY PROHIBITED
CAN NOT RECORD
REGION CODE ERROR
CHECK DISC
● An attempt has been made to record copy-protected contents.
● An attempt has been made to record copy-once contents on a
disc that is not CPRM compatible, such as DVD-R.
● A disc loaded cannot be played back on this unit since the region
number of the disc does not match that of the unit. (墌 pg. 6)
UNREADABLE DISC
CHECK DISC
● When an incompatible disc is loaded, 4 has been pressed.
(墌 pg. 6)
COULD NOT FORMAT THE DISC
CHECK THE DISC
● Formatting is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (墌 pg. 9, 74)
CAN NOT FINALISE THIS DISC
COPY PROHIBITED
CAN NOT PLAY
● The unit has detected invalid contents at the start or in the
middle of playback.
THE i.LINK DEVICE THAT YOU HAVE CONNECTED IS NOT
RECOGNIZED
MAKE SURE THAT THE DEVICE IS CONNECTED PROPERLY AND
POWERED ON
● An attempt has been made to start DV dubbing when a digital
video camera is not properly connected to the unit.
● Check the connection. (墌 pg. 58)
● Finalising is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (墌 pg. 9, 75)
CAN NOT CANCEL FINALISATION
OF THIS DISC
● Cancelling disc finalisation is not complete since the disc may be
dirty or damaged. Take out the disc, clean it and retry. (墌 pg. 9,
75)
Page 80
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Right0
DR-MH30EU_10Subsidiary.fm Page 81 Monday, July 5, 2004 11:51 AM
SPECIFICATIONS
GENERAL
VIDEO/AUDIO (HDD Deck)
Power requirement
AC 220 V – 240 Vd, 50 Hz/60 Hz
Power consumption
Power on: 37 W
Power off: 19.3 W
Temperature
Operating: 5°C to 40°C
Storage: –20°C to 60°C
Operating position
Horizontal only
Dimensions (WxHxD)
435 mm x 70 mm x 345.5 mm
Weight
6.1 kg
Input/Output
S-video input:
Y: 0.8 – 1.2 Vp-p, 75 ohms
C: 0.2 – 0.4 Vp-p, 75 ohms
S-video output:
Y: 1.0 Vp-p, 75 ohms
C: 0.3 Vp-p, 75 ohms
Video input: 0.5 – 2.0 Vp-p, 75 ohms (pin jack)
Audio input:
–8 dB, 50 kilohms (pin jack)
Corresponding to mono (left)
Audio output: –8 dB, 1 kilohms (pin jack)
i.Link: 4-pin for DV input
Component video output:
Y: 1.0 Vp-p, 75 ohms
CB/CR, PB/PR : 0.7 Vp-p, 75 ohms
Corresponding to copy protection
Digital audio output:
Optical: –18 dBm, 660 nm
Coaxial: 0.7 Vp-p, 75 ohms
Corresponding to Dolby Digital and DTS Digital Surround
Bit stream
Selectable in digital audio output setting menu
RCA connectors:
IN x 1, OUT x 1
Video recording compression system
MPEG2 (VBR)
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Recording time
VIDEO/AUDIO (DVD Deck)
Recording time
Maximum 8 hours (with 4.7 GB disc)
(XP): Approx. 1 hour
(SP): Approx. 2 hours
(LP): Approx. 4 hours
(EP): Approx. 6 hours
(FR): Approx. 1 hour – 8 hours
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Video recording compression system
MPEG2 (CBR/VBR)
Page 81
HDD capacity
EN
DR-MH30S
DR-MH20S
160 GB
80 GB
81
Recording Time
XP
1 hour
Approx. 34 hours
Approx. 17 hours
SP
2 hours
Approx. 68 hours
Approx. 34 hours
LP
4 hours
Approx. 136 hours
Approx. 68 hours
EP
6 hours
Approx. 204 hours
Approx. 102 hours
FR480
8 hours
Approx. 272 hours
Approx. 136 hours
TUNER/TIMER
Signal system
PAL-type colour signal and CCIR monochrome signal, 625 lines
50 fields
TV channel storage capacity
99 positions (+AUX position)
Tuning system
Frequency synthesized tuner
Channel coverage
VHF 47 MHz – 89 MHz/
104 MHz – 300 MHz/
302 MHz – 470 MHz
UHF 470 MHz – 862 MHz
Memory backup time
Approx. 60 seconds
ACCESSORIES
Provided accessories
RF cable,
21-pin SCART cable,
Satellite Controller,
Infrared remote control unit,
“R6” battery x 2
E.& O.E. Design and specifications subject to change without
notice.
ATTENTION:
This unit contains microcomputers. External electronic noise or
interference could cause malfunctioning. In such cases, switch the
unit off and unplug the mains power cord. Then plug it in again and
turn the unit on. Take out the disc. After checking the disc, operate
the unit as usual.
Monday, 5 July 2004 11:51
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Left0
DR-MH30EU_00.book Page 82 Tuesday, June 29, 2004 5:41 PM
82 EN APPENDIX
Language Code List
AA
Afar
IK
Inupiak
RN
Kirundi
AB
Abkhazian
IN
Indonesian
RO
Rumanian
AF
Afrikaans
IS
Icelandic
RU
Russian
AM
Ameharic
IW
Hebrew
RW
Kinyarwanda
AR
Arabic
JI
Yiddish
SA
Sanskrit
AS
Assamese
JW
Javanese
SD
Sindhi
AY
Aymara
KA
Georgian
SG
Sangho
AZ
Azerbaijani
KK
Kazakh
SH
Serbo-Croatian
BA
Bashkir
KL
Greenlandic
SI
Singhalese
BE
Byelorussian
KM
Cambodian
SK
Slovak
BG
Bulgarian
KN
Kannada
SL
Slovenian
BH
Bihari
KO
Korean (KOR)
SM
Samoan
BI
Bislama
KS
Kashmiri
SN
Shona
BN
Bengali, Bangla
KU
Kurdish
SO
Somali
BO
Tibetan
KY
Kirghiz
SQ
Albanian
BR
Breton
LA
Latin
SR
Serbian
CA
Catalan
LN
Lingala
SS
Siswati
CO
Corsican
LO
Laothian
ST
Sesotho
CS
Czech
LT
Lithuanian
SU
Sundanese
CY
Welsh
LV
Latvian, Lettish
SW
Swahili
DZ
Bhutani
MG
Malagasy
TA
Tamil
EL
Greek
MI
Maori
TE
Telugu
EO
Esperanto
MK
Macedonian
TG
Tajik
ET
Estonian
ML
Malayalam
TH
Thai
EU
Basque
MN
Mongolian
TI
Tigrinya
FA
Persian
MO
Moldavian
TK
Turkmen
FJ
Fiji
MR
Marathi
TL
Tagalog
FO
Faroese
MS
Malay (MAY)
TN
Setswana
FY
Frisian
MT
Maltese
TO
Tonga
GA
Irish
MY
Burmese
TR
Turkish
GD
Scots Gaelic
NA
Nauru
TS
Tsonga
GL
Galician
NE
Nepali
TT
Tatar
GN
Guarani
OC
Occitan
TW
Twi
GU
Gujarati
OM
(Afan) Oromo
UK
Ukrainian
HA
Hausa
OR
Oriya
UR
Urdu
HI
Hindi
PA
Panjabi
UZ
Uzbek
HR
Croatian
PL
Polish
VI
Vietnamese
HU
Hungarian
PS
Pashto, Pushto
VO
Volapuk
HY
Armenian
PT
Portuguese
WO
Wolof
IA
Interlingua
QU
Quechua
XH
Xhosa
IE
Interlingue
RM
Rhaeto-Romance
Page 82
YO
Yoruba
ZU
Zulu
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Right+
DR-MH30EU_00.book Page 83 Tuesday, June 29, 2004 5:41 PM
APPENDIX
EN
83
Country/Area Code List for Parental Lock
AD
Andorra
CK
Cook Islands
GN
Guinea
AE
United Arab Emirates
CL
Chile
GP
Guadeloupe
AF
Afghanistan
CM
Cameroon
GQ
Equatorial Guinea
AG
Antigua and Barbuda
CN
China
GR
Greece
AI
Anguilla
CO
Colombia
GS
South Georgia and the South
Sandwich Islands
AL
Albania
CR
Costa Rica
GT
Guatemala
AM
Armenia
CU
Cuba
GU
Guam
AN
Netherlands Antilles
CV
Cape Verde
GW
Guinea-Bissau
AO
Angola
CX
Christmas Island
GY
Guyana
AQ
Antarctica
CY
Cyprus
HK
Hong Kong
AR
Argentina
CZ
Czech Republic
HM
Heard Island and McDonald
Islands
AS
American Samoa
DE
Germany
HN
Honduras
AT
Austria
DJ
Djibouti
HR
Croatia
AU
Australia
DK
Denmark
HT
Haiti
AW
Aruba
DM
Dominica
HU
Hungary
AZ
Azerbaijan
DO
Dominican Republic
ID
Indonesia
BA
Bosnia and Herzegovina
DZ
Algeria
IE
Ireland
BB
Barbados
EC
Ecuador
IL
Israel
BD
Bangladesh
EE
Estonia
IN
India
BE
Belgium
EG
Egypt
IO
British Indian Ocean Territory
BF
Burkina Faso
EH
Western Sahara
IQ
Iraq
BG
Bulgaria
ER
Eritrea
IR
Iran (Islamic Republic of)
BH
Bahrain
ES
Spain
IS
Iceland
BI
Burundi
ET
Ethiopia
IT
Italy
BJ
Benin
FI
Finland
JM
Jamaica
BM
Bermuda
FJ
Fiji
JO
Jordan
BN
Brunei Darussalam
FK
Falkland Islands (Malvinas)
JP
Japan
BO
Bolivia
FM
Micronesia
(Federated States of)
KE
Kenya
BR
Brazil
FO
Faroe Islands
KG
Kyrgyzstan
BS
Bahamas
FR
France
KH
Cambodia
BT
Bhutan
FX
France, Metropolitan
KI
Kiribati
BV
Bouvet Island
GA
Gabon
KM
Comoros
BW
Botswana
GB
United Kingdom
KN
Saint Kitts and Nevis
BY
Belarus
GD
Grenada
KP
Korea, Democratic People’s
Republic of
BZ
Belize
GE
Georgia
KR
Korea, Republic of
CA
Canada
GF
French Guiana
KW
Kuwait
CC
Cocos (Keeling) Islands
GH
Ghana
KY
Cayman Islands
CF
Central African Republic
GI
Gibraltar
KZ
Kazakhstan
CG
Congo
GL
Greenland
LA
Lao People’s Democratic
Republic
CH
Switzerland
GM
Gambia
LB
Lebanon
CI
Côte d’Ivoire
Page 83
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Left+
DR-MH30EU_00.book Page 84 Tuesday, June 29, 2004 5:41 PM
84
EN
LC
APPENDIX
Saint Lucia
NU
Niue
SZ
Swaziland
LI
Liechtenstein
NZ
New Zealand
TC
Turks and Caicos Islands
LK
Sri Lanka
OM
Oman
TD
Chad
LR
Liberia
PA
Panama
TF
French Southern Territories
LS
Lesotho
PE
Peru
TG
Togo
LT
Lithuania
PF
French Polynesia
TH
Thailand
LU
Luxembourg
PG
Papua New Guinea
TJ
Tajikistan
LV
Latvia
PH
Philippines
TK
Tokelau
LY
Libyan Arab Jamahiriya
PK
Pakistan
TM
Turkmenistan
MA
Morocco
PL
Poland
TN
Tunisia
MC
Monaco
PM
Saint Pierre and Miquelon
TO
Tonga
MD
Moldova, Republic of
PN
Pitcairn
TP
East Timor
MG
Madagascar
PR
Puerto Rico
TR
Turkey
MH
Marshall Islands
PT
Portugal
TT
Trinidad and Tobago
ML
Mali
PW
Palau
TV
Tuvalu
MM
Myanmar
PY
Paraguay
TW
Taiwan
MN
Mongolia
QA
Qatar
TZ
Tanzania, United Republic of
MO
Macau
RE
Réunion
UA
Ukraine
MP
Northern Mariana Islands
RO
Romania
UG
Uganda
MQ
Martinique
RU
Russian Federation
UM
United States Minor Outlying
Islands
MR
Mauritania
RW
Rwanda
US
United States
MS
Montserrat
SA
Saudi Arabia
UY
Uruguay
MT
Malta
SB
Solomon Islands
UZ
Uzbekistan
MU
Mauritius
SC
Seychelles
VA
Vatican City State (Holy See)
MV
Maldives
SD
Sudan
VC
Saint Vincent and the
Grenadines
MW
Malawi
SE
Sweden
VE
Venezuela
MX
Mexico
SG
Singapore
VG
Virgin Islands (British)
MY
Malaysia
SH
Saint Helena
VI
Virgin Islands (U.S.)
MZ
Mozambique
SI
Slovenia
VN
Viet Nam
NA
Namibia
SJ
Svalbard and Jan Mayen
VU
Vanuatu
NC
New Caledonia
SK
Slovakia
WF
Wallis and Futuna Islands
NE
Niger
SL
Sierra Leone
WS
Samoa
NF
Norfolk Island
SM
San Marino
YE
Yemen
NG
Nigeria
SN
Senegal
YT
Mayotte
NI
Nicaragua
SO
Somalia
YU
Yugoslavia
NL
Netherlands
SR
Suriname
ZA
South Africa
NO
Norway
ST
Sao Tome and Principe
ZM
Zambia
NP
Nepal
SV
El Salvador
ZR
Zaire
NR
Nauru
SY
Syrian Arab Republic
ZW
Zimbabwe
Page 84
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_10Subsidiary.fm]
Masterpage:Right 3Column
DR-MH30EU_00.book Page 85 Tuesday, June 29, 2004 5:41 PM
APPENDIX
EN
85
TV Station And ID List
The “ID” abbreviation is what is shown on-screen in lieu of the station name. The “ID” abbreviation is listed in the Confirmation screen and
is displayed on the TV screen when the unit is tuned to a different station.
ID
STATION NAME
ID
STATION NAME
ID
STATION NAME
1000
3SAT
9LIV
AB3
ADLT
ANIM
ANT3
ARD
ARTE
ATV
B1
BBC
BBC1
BBC2
BBCW
BIO+
BLOO
BR3
C+
C1
C9
CAN5
CANV
CANZ
CH4
CH5
CHLD
CINE
CLUB
CMT
CNN
CSUR
CT1
CT2
DISC
DK1
DK2
DK4
DR1
DR2
DSF
DUNA
ETB1
ETB2
ETV
EUNW
EURO
EUSP
FEMM
FILM
FNET
FR2
FR3
FR5
GALA
HBO
HR3
HSEU
INFO
ITA1
ITA7
ITV1
TV1000
3SAT
9LIVE
AB3
ADULT
ANIMAL PLANET
ANTENA3
ARD
ARTE
MAGYAR ATV
BERLIN 1
BBC GROUP
BBC1
BBC2
BBC WORLD
TV BIO+
BLOOMBERG
BAYERN3
CANAL PLUS
PORTUGUSES
VALENCIA
CANALE5
KETNET CANVAS
KANAAL Z
CHANNEL4
CHANNEL5
CHILD
CINEMA
TELECLUB
CMT
CNN
ANDALUCIA
CT 1
CT 2
DISCOVERY
DENMARK1
DENMARK2
DENMARK4
DR TV
DR2
DSF
DUNA TV
ETB1
ETB2
ETV
EURO NEWS
EURONEWS
EUROSPORTS
FEMMAN
FILM
FILMNET
France2
France3
France5
GALAVISION
HBO
HESSEN3
H.S.EURO
INFO-KANAL
ITALIA1
ITALIA7
ITV
JIM
JSTV
KA2
KAB1
KAN2
KAN5
KBH
KIKA
LA7
LIB
LOCA
M6
MBC
MCM
MDR
MOVE
MTV
MTV1
MTV2
MTV3
NGEO
N24
N3
N-TV
NBC
NDR
NED1
NED2
NED3
NET5
NEWS
NICK
NOVA
NRK1
NRK2
ODE
ORF1
ORF2
PHOE
POLS
PREM
PRIM
PRO7
RAI1
RAI2
RAI3
RET4
RTB1
RTB2
RTL
RTL2
RTL4
RTL5
RTL7
RTLK
RTP
RTV4
SAT1
SBS6
SERV
SF1
SF2
JIM TV
JSTV
KA2
KABEL1
KANAL2
KANAL5
KBH.KANAL
KINDER.KANAL
LA7
LIBERTY TV
LOCAL
M6
MBR
MCM
MDR
MOVIE
MTV
MTV1
MTV2
MTV3
NATIONAL.G
NEWS24
NORD3
N-TV
NBC SUPER
NDR
NED1
NED2
NED3
NETWORK5
SHOW
SIC
SKY
SKYN
SPEK
SPRT
SRTL
STAR
SVT1
SVT2
SV24
SWR
TCC
TCM
TELE
TELE5
TF1
TM
TMC
TMF
TNT
TRT
TSI1
TSI2
TSR1
TSR2
TV1
TV2
TV2Z
TV3
TV3+
TV4
TV5
TV6
TV8
TVE1
TVE2
TVG
TVI
TVN
TV24
TVP1
TVP2
TV P
V8
VCR
VH-1
VIT
VIVA
VIV2
VMTV
VOX
VSAT
VT4
VTM
WDR3
WRLD
YLE1
YLE2
YORN
ZDF
ZTV
SHOW
SOCIEDADE
SKY CHANNEL
SKY NEWS
SPEKTRUM
SPORT
SUPER RTL
STAR-TV
SVT1
SVT2
NEWS
SUEDWEST3
TCC
TCM
TELE
TELE5
TF1
TV DE MADRID
TELEMONTECARLO
TMF
TNT INT
TRT INT
TSI
TSI2
TSR
TSR2
BRTN TV1
TV2
TV2 ZULU
TV3
TV3 PLUS
TV4
TV5
TV6
TV8
TVE1
TVE2
TV GALICIA
TV INDEPENDENT
TV NORGE
TVN24
TVP1
TVP2
TV POLONIA
V8
VIDEO
VH-1
VITAYA
VIVA
VIVA2
VIDEO MUSIC
VOX
VIASAT3
VT4
VTM
West3
WORLD
YLE1
YLE2
YORIN
ZDF
ZTV
Page 85
NICKELODEON
NOVA
NRK
NRK2
ODEON
ORF1
ORF2
PHOENIX
POL SAT
PREMIERE
PRIMA TV
PRO7
RAI1
RAI2
RAI3
RETE4
TELE21
RTBF1 or 2
RTL
RTL2
RTL4
RTL5
RTL7
RTLK
RTP
RTV4
SAT1
SBS
Service
SF1
SF2
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_11IX.fm]
Masterpage:Left0
DR-MH30EU_00.book Page 86 Tuesday, June 29, 2004 5:41 PM
86
EN
LIST OF TERMS
A
O
A-B Repeat Playback ................................................ 31
Adjusting The Picture Quality ..................................... 32
Angle Selection ........................................................ 28
Audio Channel Selection ........................................... 29
Audio Language/Sound Selection ............................... 29
Auto Channel Set ..................................................... 70
One Touch Replay .............................................. 29, 43
On-screen Bar .......................................................... 30
On-screen Language Set ........................................... 21
C
Cancel And Change Programmes .............................. 47
Check Programmes .................................................. 47
P
Pan&Scan ................................................................ 22
Play List ................................................................... 52
Playback Control (PBC) ............................................. 29
Programme Playback ................................................ 33
Progressive scan ...................................................... 69
D
R
Delete Title .............................................................. 51
Disc menu ............................................................... 26
Disc Remaining Time ...........................................36, 39
Disc Resume ........................................................... 68
Discs For Playback Only ............................................. 6
DVD menu ............................................................... 26
Random Playback ..................................................... 33
Recordable/playable discs ........................................... 5
Recording Medium And Format .................................... 7
Recording Mode ................................................. 35, 38
Recording Resume Function ................................ 35, 38
Region Number .......................................................... 6
Register Disc ............................................................ 54
Relief Recording ....................................................... 46
Repeat Playback ...................................................... 31
Resume Function ..................................................... 27
E
Elapsed Recording Time Indication .......................36, 39
F
File Structure Of Discs ................................................ 7
Free Rate Function ................................................... 37
G
Guide Program Number ............................................ 70
H
High-Speed Search .............................................26, 40
I
Instant Timer Recording (ITR) ...............................36, 39
Interlaced scan ......................................................... 69
J
Jump Search ............................................................ 43
Just Clock ................................................................ 73
L
Letter Box ................................................................ 22
Live Memory ............................................................ 41
Live Memory Recording ............................................ 43
S
Select The Switching Interval Of The Slide Show ......... 33
Setting The Progressive Mode ................................... 33
Simulated Surround Effect ......................................... 32
Skip Search ....................................................... 27, 40
Slow Motion ....................................................... 27, 40
Still Picture/Frame-By-Frame Playback ................. 27, 40
Subtitle Selection ...................................................... 28
T
Temporary Recording ................................................ 41
Time Search ............................................................ 32
Top menu ................................................................ 26
U
Unplayable Discs ........................................................ 6
V
VPS/PDC Recording ................................................. 45
M
Manual Channel Set ................................................. 71
Marking Positions To Play Back Again Later ................ 27
Menu/Audio/Subtitle Language Set ............................. 21
Page 86
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_11IX.fm]
DR-MH30EU_00.book Page 87 Tuesday, June 29, 2004 5:41 PM
Masterpage:Right-No-Heading
MEMO
Page 87
EN
87
Tuesday, 29 June 2004 17:40
Filename [DR-MH30EU_12Cov4.fm]
DR-MH30EU_00.book Page 88 Tuesday, June 29, 2004 5:41 PM
EN
DR-MH30S/
DR-MH20S
OPEN/
CLOSE
T
VI
HDD
CANCEL
LIVE
DU
T
TOP MENU
MENU
PREVIOUS
SLOW
REC
JUMP
REC MODE
SAT
AUDIO
COPYRIGHT © 2004 VICTOR COMPANY OF JAPAN, LTD.
Page 88
E
Printed in Germany
0704MNH-ID-VE
June 29, 2004 5:40 pm
DIS
VPS/
SUB
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement