Image | Treadmill HGTL09130N | User manual | Image Treadmill HGTL09130N User manual

®
Model No. HGTL09130M
HGTL09130N
Serial No.
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guarantee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent
Pending
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.imagefitness.com
new products, prizes,
fitness tips, and much more!
®
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and PART LIST are attached in the center of this manual.
IMAGE is a registered trademark of ICON Health & Fitness, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
13. Keep the power cord and the surge suppressor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the treadmill is not working properly.)
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
17. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord from the front of the treadmill
and move the on/off switch to the off position
when the treadmill is not in use. (See the
drawing on page 5 to locate the on/off switch.)
10. When connecting the power cord (see page 8),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 21.) You
must be able to safely lift 45 pounds (20 kg) in
order to raise, lower, or move the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 8. To purchase a surge suppressor, see
your local IMAGE dealer or call 1-800-806-3651
and order part number 146148.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
21. When folding or moving the treadmill, make
sure that the storage latch and the console
latch are fully closed.
3
22. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or incline changes. In some instances, the speed
and/or incline may change before the personal trainer describes the change.
25. Inspect and properly tighten all parts of the
treadmill regularly.
26. Never insert or drop any object into any
opening.
27.
DANGER: Always unplug the power
23. When using iFIT.com CDs and videos, you
can manually override the speed and incline
settings at any time by pressing the speed
and incline buttons. However, when the next
“chirp” is heard, the speed and/or incline will
change to the next settings of the CD or video
program.
cord from the front of the treadmill immediately after use, before cleaning the treadmill,
and before performing the maintenance and
adjustment procedures described in this manual. Never remove the motor hood unless instructed to do so by an authorized service
representative. Servicing other than the procedures in this manual should be performed
by an authorized service representative only.
24. Always remove iFIT.com CDs and videos from
your CD player or VCR when you are not
using them.
28. This treadmill is intended for in-home use
only. Do not use this treadmill in any commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown below have been placed on your treadmill. If the decal is missing,
or if it is not legible, please call our Customer Service Department, toll-free, to order
a free replacement decal (see ORDERING REPLACEMENT PARTS on the back cover
of this manual). Apply the decal in the location shown. Note: The decal at the right is
shown at 40% of actual size.
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary IMAGE®
EXECUTIVE 2002 treadmill. The EXECUTIVE 2002
treadmill combines advanced technology with innovative design to help you get the most from your exercise
program in the convenience of your home. And when
you’re not exercising, the unique EXECUTIVE 2002
treadmill can be folded up and stored in the cabinet.
Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note
the product model number and serial number before
calling. The model number is HGTL09130M or
HGTL09130N. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after reading this manual, please call our Customer Service
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Book Holder
Console
Pulse Sensor
Console Latch
Handrail
Key/Clip
Storage Latch
RIGHT SIDE
LEFT SIDE
Circuit Breaker
On/Off Switch
Walking Belt
Foot Grip
Rear Roller
Adjustment Bolts
5
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area. Do not remove the cardboard from the
area shown in drawing 2 below. Remove all other packing materials. Do not dispose of any packing materials
until assembly is completed. Treadmill assembly requires the included allen wrench and your own phillips
screwdriver
and 9/16” wrench
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. While a second person holds one end of the treadmill,
carefully tip the treadmill onto its side as shown. Using the
included allen wrench and a 9/16” wrench, attach the two
Extension Legs (70) to the base of the Uprights (109) with
the four Bolts (71) and Nuts (74). Make sure that the
Extension Legs are turned so the Base Pads (66) are in the
positions shown.
1
74
66
70
With the help of a second person, carefully raise the
treadmill to the vertical position, and then lower the
Walking Platform (93) to the floor. Note: If the treadmill rocks
slightly, tip the treadmill back onto its side, loosen the four
Nuts (74), adjust the positions of the Extension Legs (70),
and then retighten the Nuts. Raise the treadmill back to the
vertical position. Repeat until the rocking motion is eliminated.
2. Attach the Storage Latch Assembly (33) and the Latch
Spacer (35) to the left Upright (109) with the two 3/4”
Screws (67) as shown. Be careful not to overtighten
the Screws.
71
93
74
109
66
70
71
2
Felt
35
Thread the Console Latch (55) into the right Upright (109).
67
33
55
Felt
109
3. Pull the Console Latch (55) to the right, and rotate the
Console Base (43) to the position shown. Release the
Console Latch, making sure that the Console Base is
locked in place. Note: It may be helpful to push down on
the right Handrail (39) and push the Console Latch into
the locked position.
3
43
Note: If the Handrail (39) rocks, attach one or two pieces
of the included felt onto the bracket in the locations
shown in drawing 2.
39
6
55
4a. Make sure that the treadmill is less than six feet away
from the cabinet.
4a
Note: There are two ways to connect the treadmill to an
outlet. First, the cabinet has a power cord that can be
plugged into the treadmill and another power cord that
can be plugged into an outlet using a surge suppressor.
Second, the treadmill power cord can be plugged into
the treadmill and into an outlet using a surge suppressor.
To connect the treadmill using the cabinet power cord,
follow the instructions in this step. To connect the treadmill using the treadmill power cord, see step 4b.
Important: All references to power cords in other
sections of this manual apply to both the cabinet
power cord and the treadmill power cord.
Cabinet
Audio
Wire
76
Cabinet
Power
Cord
Feed the cabinet power cord and the cabinet audio wire
through the looped Plastic Tie (76) at the front of the
treadmill. Plug the power cord and the audio wire into the
treadmill as shown. Tighten the Plastic Tie. (The Plastic
Tie can also be released if needed.)
4b. Plug the Treadmill Power Cord (123) into the front of the
treadmill as shown.
4b
123
5. Locate the indicated wire on the back of the cabinet. Plug
the wire into the connection panel.
If you plan to use one or both of the power cords on the
back of the cabinet, plug the power cords into appropriate
outlets using surge suppressors as described on page 8.
5
Connection
Panel
Power
Cord
Wire
6. Make sure that all parts are properly tightened before you use the treadmill. Note: If there is a thin sheet
of clear plastic on the console decal, remove it. Keep the
included allen wrench in a secure place. The allen
wrench is used to adjust the walking belt (see page 24).
To protect the floor or carpet from damage, place a mat
under the treadmill.
7
Power
Cord
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local IMAGE dealer or call 1-800-806-3651 and
order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used, it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having
8
CONSOLE DIAGRAM
Manual/Program Indicators
Program Display
Display
If there is a thin sheet of clear plastic
on the face of the console, remove it.
Display
Program Indicators
Clip
Key
Nine certified personal trainer programs are also
offered. Each program automatically controls the
speed and incline of the treadmill to give you an effective jogging or running workout. Two heart rate programs are also featured. Each program controls the
speed and incline of the treadmill to keep your heart
rate near a target level during your workouts. Note:
The heart rate programs require the use of the optional
chest pulse sensor.
CAUTION: Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turning on the power.
• Always wear the clip (see the drawing
above) while operating the treadmill.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
The console also features new iFIT.com interactive
technology. Having iFIT.com technology is like having a
personal trainer in your home. Using the included audio
cable, you can connect the treadmill to your home
stereo, portable stereo, computer, or VCR and play
special iFIT.com CD and video programs (iFIT.com
CDs and videocassettes are available separately).
iFIT.com CD and video programs automatically control
the speed and incline of the treadmill as a personal
trainer coaches you through every step of your workout.
High-energy music provides added motivation. To purchase iFIT.com CDs or videocassettes, call tollfree 1-800-735-0768.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed water
bottle in the water bottle holder.
FEATURES OF THE CONSOLE
The advanced console offers an impressive array of
features to help you get the most from your exercise.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
a touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the handgrip pulse sensor or the optional chest pulse sensor (see page 20).
With the treadmill connected to your computer, you
can also go to our Web site at www.iFIT.com and access programs directly from the internet. Additional options are soon to be available. See www.iFIT.com for
more information.
9
HOW TO TURN ON THE POWER
1
Plug in the power cord (see page 8).
2
Locate the on/off
switch on the treadmill
near the power cord.
Move the on/off
switch to the on position.
3
the Speed + and – buttons. Each time a button
is pressed, the speed
setting will change by
0.1 mph; if a button is
held down, the speed
setting will change in increments of 0.5 mph. To
change the speed setting quickly, press the Quick
Speed Control buttons.
On
Position
To stop the walking belt, press the Stop button.
The Time/Segment Time display will begin to
flash. To restart the walking belt, press the Start
button or the Speed + button.
Stand on the foot rails
of the treadmill. Find
the clip attached to the
key and slide the clip
onto the waistband of
your clothes. Next, insert the key into the console. After a moment, the
displays and various indicators will light. Test the
clip by carefully taking a few steps backward
until the key is pulled from the console. If the
key is not pulled from the console, adjust the
position of the clip as needed.
Note: During the first few minutes that the treadmill
is used, inspect the alignment of the walking belt,
and align it if necessary (see page 24).
4
To change the incline of
the treadmill, press the
Incline buttons. Each time
a button is pressed, the
incline will change by
0.5%. Note: After the buttons are pressed, it may take a moment for the
treadmill to reach the selected incline setting.
To use the manual mode of the console, follow the
steps beginning on page 10. To use a personal trainer
program, see page 12. To use a heart rate program,
see page 13. To use an iFIT.com CD or video program, see page 17. To use an iFIT.com program directly from our Web site, see page 19.
5
Insert the key fully into the console.
See HOW TO TURN ON THE POWER above.
2
3
Follow your progress with the LED track and
the displays.
The LED Track—
When the manual
mode or the
iFIT.com mode is
selected, the program display will
show an LED track
representing 1/4 mile. As you exercise, the indicators around the track will light in sequence until you
have completed 1/4 mile. A new lap will then
begin.
HOW TO USE THE MANUAL MODE
1
Change the incline of the treadmill as desired.
Select the manual
mode.
When the key is inserted, the manual
mode will be selected
and the Manual indicator will light. If a program has been
selected, press the Program button repeatedly to
select the manual mode.
Distance/Incline/
Laps display—This display shows the distance
that you have walked, the
incline level of the treadmill, and the number of
1/4-mile laps you have completed. The display will
change from one number to the next every few
seconds. The Incline indicator or the Laps indicator
will light when the incline level or the number of
laps is shown. Note: Each time the Incline buttons
are pressed, the display will show the current incline setting for several seconds.
Press the Start button or the Speed + button to
start the walking belt.
A moment after the button is pressed, the walking
belt will begin to move at 1 mph. Hold the handrails
and begin walking. As you exercise, change the
speed of the walking belt as desired by pressing
10
Time/Segment Time
display—When the manual mode or the iFIT.com
mode is selected, this
display will show the
elapsed time. When a
personal trainer program or a heart rate program is
selected, the display will show both the time remaining in the program and the time remaining in
the current segment of the program. The display
will alternate between one number and the other
every few seconds. The Segment Time indicator
will light when the segment time is shown.
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
6
Measure your heart rate, if desired.
Note: If you hold the handgrip pulse sensor
and wear the optional chest pulse sensor at
the same time, the console may not display
your heart rate accurately. Before using the
handgrip pulse sensor, make sure that your
hands are clean.
To measure your
heart rate, stand
on the foot rails
and place your
hands on the
metal contacts on
the handrail. Your
Metal
palms must be
Contacts
resting on the
upper contacts,
and your fingers must be touching the lower contacts—avoid moving your hands. When your
pulse is detected, the heart-shaped indicator in the
Calories/Fat Calories/Heart Rate display will flash,
and then your heart rate will be shown. For the
most accurate heart rate reading, continue to
hold the contacts for about 15 seconds.
Calories/Fat Calories/
Heart Rate display—
This display shows the
approximate numbers of
calories and fat calories
you have burned (see
FAT BURNING on page 25). This display will also
show your heart rate when you use the handgrip
pulse sensor or the optional chest pulse sensor.
Every few seconds, the display will change from
one number to the next. The Fat Cals. indicator or
the Heart Rate indicator will light when the number of fat calories or your heart rate is shown.
Speed/Min-mile
display—This display
shows the speed of the
walking belt and your
current pace (pace is
measured in minutes per
mile). Every few seconds, the display will change
from one number to the other. The Min/ Mile indicator will light when your pace is shown.
7
When you are finished, remove the key from
the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting when the treadmill is folded to the storage
position or the treadmill will be damaged. Next,
remove the key from the console and put it in a secure place. Note: If the displays and various indicators on the console remain lit after the key
is removed, the console is in the “demo”
mode. See page 20 and turn off the demo mode.
Note: The console can
display speed and distance in either miles or
kilometers. To find which
unit of measurement is
selected, hold down the
Stop button while inserting the key into the console. An E, for English miles, or an M, for metric
kilometers, will appear in the display. Press the
Speed + button to change the unit of measurement. When the desired unit of measurement is
selected, remove the key and then reinsert it.
Note: For simplicity, all instructions in this
manual refer to miles.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord from the front
of the treadmill.
11
the flashing Current
Current Segment
Segment column of
the program display.
(The incline settings
are not shown in the
program display.)
The speed settings
for the next several
segments will be shown in the columns to the
right.
HOW TO USE PERSONAL TRAINER PROGRAMS
1
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page 10.
2
Select one of the personal trainer programs.
When the key is
inserted, the
manual mode will
be selected. To
select one of the
personal trainer
programs, press
the Program button repeatedly until one of the
nine personal trainer program indicators lights.
When a personal trainer program is selected, the
Distance/Incline/Laps display will flash the maximum incline setting for the program for six seconds, and the Speed/Min-mile display will flash
the maximum speed setting.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
tone will sound. In addition, if the speed and/or incline of the treadmill is about to change, the
Speed/Min-mile display and/or the Distance/
Incline/Laps display will flash to alert you, and
three tones will sound. When the first segment is
completed, all speed settings will move one column to the left. The speed setting for the second
segment will then be shown in the flashing
Current Segment column and the treadmill will automatically adjust to the speed and incline settings
for the second segment.
The console features four jogging programs and
five running programs. The profiles on the console
show how the speed and incline of the treadmill
will change during the programs. The numbers
beside the profiles show the maximum speed and
incline settings for the programs.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and no time remains in
the Time/Segment Time display. The walking belt
will then slow to a stop.
The program display will show a
simplified profile of
the program you
have selected. The
Time/Segment
Time display will
show how long the program will last.
3
Note: Each time a segment ends and the speed
settings move one column to the left, if all of the
indicators in the Current Segment column are lit,
the speed settings will move downward so that only
the highest indicators in the columns will appear in
the program display. When the speed settings
move to the left again and not all of the indicators
in the Current Segment column are lit, the speed
settings will move back up.
Press the Start button or the Speed + button to
start the program.
If the speed or incline setting for the current
segment is too high or too low, you can manually
override the setting by pressing the Speed or
Incline buttons on the console. Every few times
one of the Speed buttons is pressed, an additional
indicator will light or darken in the Current Segment
column. If any of the columns to the right of the
Current Segment column have the same number
of lit indicators as the Current Segment column,
an additional indicator may light or darken in those
columns as well. Note: If you manually adjust the
speed setting so that all of the indicators in the
Current Segment column are lit, the speed settings
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided into several time segments of different lengths. The Time/Segment
Time display shows both the time remaining in the
program and the time remaining in the current
segment. One speed setting and one incline setting are programmed for each segment. The
speed setting for the first segment will be shown in
12
in the program display will not move downward as
described above. When the current segment of
the program ends, the treadmill will automatically adjust to the speed and incline settings
for the next segment.
HOW TO USE HEART RATE PROGRAMS
CAUTION:
If you have heart problems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regularly, consult your physician to find whether the
medication will affect your exercise heart rate.
To stop the program temporarily, press the Stop
button. The Time/Segment Time display will begin
to flash. To restart the program, press the Start button or the Speed + button. The walking belt will
begin to move at 1 mph. When the current segment of the programs ends, the treadmill will automatically adjust to the speed and incline settings
for the next segment. To end the program at any
time, press the Stop button, remove the key, and
then reinsert the key.
4
Follow the steps below to use the heart rate programs.
Note: You must wear the optional chest pulse sensor (see page 20) to use the heart rate programs.
Follow your progress with the displays.
1
See the instructions included with the optional
chest pulse sensor.
See step 5 on page 10.
5
Measure your heart rate, if desired.
2
See step 6 on page 11.
6
Put on the chest pulse sensor.
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
10.
When the program is completed, remove the
key from the console.
3
When the program has ended, make sure that
the incline of the treadmill is at the lowest setting. Next, remove the key from the console and
put it in a safe place. Note: If the displays and
various indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. See page 20 and turn off the
demo mode.
Select a heart rate program.
When the key is
inserted, the manual mode will be
selected. To select one of the
heart rate programs, press the
Program button repeatedly until one of the two
heart rate program indicators lights.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord from the front
of the treadmill.
The two lower profiles on the left side of the console show how the target heart rate will change
during the programs. The numbers beside the
profiles show the minimum and maximum target
heart rate settings for the programs. Note: The
numbers are percentages of your estimated maximum heart rate. Your estimated maximum heart
rate is determined by subtracting your age from
220. For example, if you are 30 years old, your
estimated maximum heart rate is 190 beats per
minute (220 – 30 = 190). 50% of your estimated
maximum heart rate would be 95 beats per minute
(50% of 190 is 95).
13
ries of tones will sound, and the Distance/Incline/
Laps display and the Speed/Min-mile display will
flash. When the first segment is completed, all
heart rate settings will move one column to the
left. The heart rate setting for the second segment
will then be shown in the flashing Current
Segment column, and the speed and/or incline of
the treadmill will change, if needed, to bring your
heart rate closer to the heart rate setting for the
second segment.
The program display will show a
simplified profile of
the program you
have selected. The
Time/Segment
Time display will
show how long the program will last.
4
Enter your age.
The program will continue until the target heart
rate setting for the last segment is shown in the
Current Segment column and no time remains in
the program. The walking belt will then slow to a
stop.
When a heart rate program is selected, the
word AGE will begin to
flash in the Distance/
Incline/Laps display. You
must enter your age to
use a heart rate program. If you have already entered your age, go to step 5. If you have not entered your age, press the Incline (Age Set) buttons
until your age is shown. Your age will then be
saved in memory.
5
If the speed or incline setting for the current segment is too high or too low, you can adjust the setting with the Speed or Incline buttons. However, if
you decrease the speed, the incline will automatically increase; if you increase the speed, the incline will decrease. If you increase the incline, the
speed will decrease; if you decrease the incline,
the speed will increase. The treadmill will always
attempt to keep your heart rate near the target
heart rate setting for the current segment. Note:
When the incline reaches the lowest setting, the
speed cannot be increased further. When the incline reaches the highest setting, the speed cannot be decreased further.
Press the Start button or the Speed + button to
start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each heart rate program is divided into one-minute
segments. The Time/Segment Time display will
show both the time remaining in the program and
the time remaining in the current segment of the
program. One target heart rate setting is programmed for each segment. (The same target
heart rate setting may be programmed for consecutive segments.) The
target heart rate
Current Segment
setting for the first
segment will be
shown in the flashing Current
Segment column of
the program display. The target
heart rate settings for the next several segments
will be shown in the columns to the right.
If your pulse is not detected during the program,
the letters PLS will flash in the Calories/Fat
Calories/Heart Rate display and the speed and incline of the treadmill may automatically decrease
until your pulse is detected. If this occurs, see the
instructions included with the chest pulse sensor.
To stop the program at any time, press the Stop
button. Heart rate programs should not be stopped
temporarily and then restarted. To use a heart rate
program again, reselect the program and start it at
the beginning.
6
Follow your progress with the displays.
See step 5 on page 10.
7
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash, a se-
When the program is completed, remove the
key from the console.
See step 6 on page 13.
14
HOW TO CONNECT YOUR CD PLAYER, VCR,
OR COMPUTER TO THE CABINET
To use iFIT.com CDs, your portable CD player,
portable stereo, home stereo, or computer with CD
player must be connected to the cabinet. See pages 15
and 16 for connecting instructions. To use iFIT.com
videocassettes, your VCR must be connected to the
cabinet. See page 17. To use iFIT.com programs directly from our Web site, your home computer must
be connected to the cabinet. See page 16. Note: This
section describes how your equipment can be connected to the jack on the connection panel inside
the cabinet. However, your equipment can be connected to the lower jack in the cabinet or the jack
on the front of the treadmill in the same way.
HOW TO CONNECT YOUR PORTABLE STEREO
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
A. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into the included adapter. Plug the
adapter into an AUDIO OUT jack on your stereo.
A
Connection
Panel on
Cabinet
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Audio
Cable
Adapter
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into the LINE OUT jack on your CD
player. Plug your headphones into the PHONES jack.
B. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into the LINE OUT jack on your
stereo.
A
B
PHONES LINE OUT
Connection
Panel on
Cabinet
LINE OUT
PHONES
Connection
Panel on
Cabinet
Headphones
Audio
Cable
B. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into a 3.5mm Y-adapter (available
at electronics stores). Plug the Y-adapter into the
PHONES jack on your CD player. Plug your headphones into the other side of the Y-adapter.
LINE OUT
Audio
Cable
C. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into a 3.5mm Y-adapter (available
at electronics stores). Plug the Y-adapter into the
PHONES jack on your stereo. Plug your headphones into the other side of the Y-adapter.
C
B
PHONES
Connection
Panel on
Cabinet
PHONES
Audio
Cable
Connection
Panel on
Cabinet
3.5mm
Y-adapter
PHONES
Audio
Cable
Headphones
3.5mm
Y-adapter
Headphones
15
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into the included adapter. Plug the
adapter into the LINE OUT jack on your stereo.
A. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into the LINE OUT jack on your
computer.
A
A
CD
VCR
Amp
Connection
Panel on
Cabinet
LINE OUT
LINE OUT
Audio
Cable
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into a 3.5mm Y-adapter (available
at electronics stores). Plug the Y-adapter into the
PHONES jack on your computer. Plug your headphones or speakers into the other side of the Yadapter.
B. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into the included adapter. Plug the
adapter into an RCA Y-adapter (available at electronics stores). Next, remove the wire that is currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the LINE OUT
C
jack on your stereo.
B
B
Connection
Panel on
Cabinet
CD
Amp
PHONES
Audio
Cable
VCR
Connection
Panel on
Cabinet
LINE OUT
Connection
Panel on
Cabinet
3.5mm
Y-adapter
LINE OUT
Headphones/Speakers
Audio
Cable
RCA
Y-adapter
Adapter
Wire removed from
LINE OUT jack
16
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 16.
To use iFIT.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT YOUR CD PLAYER,
VCR, OR COMPUTER TO THE CABINET on page 15.
Note: To purchase iFIT.com CDs or videocassettes, call toll-free 1-800-735-0768.
A. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into the included adapter. Plug the
adapter into the AUDIO OUT jack on your VCR.
A
Follow the steps below to use an iFIT.com CD or video
program.
ANT. IN
VIDEO AUDIO
IN
1
RF OUT
CH
3 4
OUT
AUDIO OUT
Connection
Panel on
Cabinet
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 10.
RIGHT
LEFT
Audio
Cable
2
Adapter
Select the iFIT.com mode.
When the key is
inserted, the
manual mode will
be selected. To
use iFIT.com
CDs or videocassettes, press the
Program button repeatedly until the iFIT.com indicator lights.
B. Plug one end of the audio cable into the jack on the
connection panel inside the cabinet. Plug the other
end of the cable into the included adapter. Plug the
adapter into an RCA adapter (available at electronics stores). Next, remove the wire that is currently
plugged into the AUDIO OUT jack on your VCR and
plug the wire into the unused side of the RCA
adapter. Plug the RCA adapter into the AUDIO OUT
jack on your VCR.
3
Insert the iFIT.com CD or videocassette.
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
B
ANT. IN
4
VIDEO AUDIO
IN
RF OUT
CH
3 4
OUT
Connection
Panel on
Cabinet
A moment after the button is pressed, your personal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time/Segment Time display is flashing, press the Start button or the
Speed + button on the console. The treadmill will
not respond to a CD or video program when the
Time/Segment Time display is flashing.
RCA Y-adapter
Audio
Cable
Press the PLAY button on your CD player or
VCR.
Adapter
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
17
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the console may not detect the program signals.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time display will begin to flash. To restart the program, press the Start button or the Speed + button. After a moment, the walking belt will begin to
move at 1.0 mph. When the next “chirp” is
heard, the speed and incline will change to the
next settings of the CD or video program. The
program can also be stopped by pressing the
Stop button on your CD player or VCR.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
5
Follow your progress with the LED track and
the displays.
See step 5 on page 10.
6
When the CD or video program is completed, the
walking belt will stop and the Time/Segment Time
display will begin to flash. Note: To use another
CD or video program, press the Stop button or remove the key and go to step 1 on page 17.
Measure your heart rate, if desired.
See step 6 on page 11.
7
When the program is completed, remove the
key from the console.
See step 6 on page 13.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player or VCR
when you are finished using them.
• Make sure that the iFIT.com indicator is lit and
that the Time/Segment Time display is not
flashing. If the Time/Segment Time display is
flashing, press the Start button or the Speed
+ button on the console.
18
7
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
Our Web site at www.iFIT.com allows you to access
basic programs, audio programs, and video programs
directly from the internet. Additional options are soon
to be available. See www.iFIT.com for details.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 16. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements will be found on our Web site.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
Follow the steps below to use a program from our
Web site.
1
Insert the key into the console.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time display will begin to flash. To restart the program, press the Start button or the Speed + button. After a moment, the walking belt will begin to
move at 1.0 mph. When the next “chirp” is
heard, the speed and incline will change to the
next settings of the program.
See HOW TO TURN ON THE POWER on page 10.
2
Select the iFIT.com mode.
When the key is
inserted, the
manual mode will
be selected and
the Manual indicator will light. To
use a program
from our Web site, press the Program button repeatedly until the iFIT.com indicator lights.
3
Go to your computer and start an internet
connection.
4
Start your web browser, if necessary, and go to
our Web site at www.iFIT.com.
5
Follow the desired links on our Web site to select a program.
When the program is completed, the walking belt
will stop and the Time/Segment Time display will
begin to flash. Note: To use another program,
press the Stop button and go to step 5.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time/Segment Time display is not flashing.
In addition, make sure that the audio cable is
properly connected, that it is fully plugged in,
and that it is not wrapped around a power cord.
8
Read and follow the on-line instructions for using a
program.
6
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
Follow your progress with the LED track and
the displays.
See step 5 on page 10.
9
Follow the on-line instructions to start the
program.
When the program is completed, remove the
key from the console.
See step 6 on page 13.
When you start the program, an on-screen countdown will begin.
19
THE INFORMATION MODE/DEMO MODE
THE OPTIONAL CHEST PULSE SENSOR
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also
allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
An optional chest pulse sensor adds even more features to the console. The chest pulse sensor offers
hands-free operation and continuously monitors your
heart rate during your workouts. To purchase the optional chest pulse sensor, call toll-free 1-800-7342377.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following information will be shown:
The Distance/Incline/Laps
display will show the total
number of miles that the walking belt has moved.
The Time/Segment Time display will show the total number of hours the treadmill has
been used.
An E, for English miles, or an
M, for metric kilometers, will
appear in the Speed/Min-Mile
display. Press the Speed +
button to change the unit of
measurement.
IMPORTANT: The Calories/
Fat Calories/Heart Rate display should be blank. If a “d”
appears in the display, the
console is in the “demo”
mode. This mode is intended
to be used only when a treadmill is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the displays and indicators on the console
will automatically light in a preset sequence, although
the buttons on the console will not operate. If a “d” appears in the Calories/Fat Calories/Heart Rate display when the information mode is selected, press
the Speed – button so the display is blank.
To exit the information mode, remove the key from the
console.
20
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the lowest position. If this is not done, the treadmill may
be damaged. Next, UNPLUG THE POWER CORD FROM THE FRONT OF THE TREADMILL. CAUTION: You
must be able to safely lift 45 pounds (20 kg) in order to raise, lower, or move the treadmill.
1. Pull the console latch to the right and rotate the console
base to the storage position. (Note: It may be helpful to
push down on the right handrail as you pull the console
latch.) Release the console latch, making sure that the console base is locked in the storage position.
Next, hold the treadmill with your hands in the locations
shown. CAUTION: To decrease the possibility of injury,
bend your legs and keep your back straight. As you
raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
Console
Latch
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the storage latch
to the left and hold it. Raise the treadmill until the catch
plate is past the pin on the storage latch. Slowly release
the storage latch. Make sure that the pin is securely
holding the catch plate as shown.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit.
Knob
Plate
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the
pin on the storage latch is securely holding the catch plate.
1. Hold the handrails as shown and place one foot against
one of the wheels.
Handrail
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Note: If
the power cord from the cabinet is connected to the treadmill, roll the treadmill no more than six feet from the cabinet. Never move the treadmill without tipping it back.
To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot on the wheel, and carefully lower the treadmill until it is resting in the storage position. Note: If the
treadmill is inside the cabinet, make sure that the treadmill
is fully inside before closing the cabinet doors.
21
Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left hand, pull the storage latch to
the left and hold it. Pivot the treadmill down until the
frame is past the pin on the storage latch.
Storage
Latch
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. CAUTION: To decrease the possibility of injury, bend your legs and keep your back
straight. Do not drop the treadmill.
Next, pull the console latch to the right and rotate the console base to the position shown. Release the console
latch, making sure that the console base is locked in
place. Note: It may be helpful to push down on the right
handrail and then push the console latch into the locked
position.
22
Console
Latch
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 8. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. Make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill near
the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker,
wait for five minutes and then press the switch back in.
d. Check the on/off switch located on the treadmill near the
power cord. The switch must be in the on position.
c
Reset
Tripped
d
On
Position
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker (see c. above).
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. Make sure that the on/off switch is in the on position.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Using a flat screwdriver, carefully pry the Front Wheel
Covers (59) off both Front Wheels (57). Look between the
spokes of the Front Wheels and locate the Hood Screws
(80) (rotate the Front Wheels, if necessary). Remove a
Hood Screw from each side of the Motor Hood (1). Raise
the incline about 3%, remove the key from the console,
and unplug the power cord from the front of the treadmill. Carefully remove the Motor Hood by pulling it in the
direction shown.
a
80
1
59
Locate the Reed Switch (20) and the Magnet (9) on the
left side of the Pulley (8). Turn the Pulley until the Magnet
is aligned with the Reed Switch. Loosen the 1/2” Screw
(41), and slide the Reed Switch as close as possible to
the Magnet; make sure that the Magnet will not hit the
Reed Switch. Retighten the Screw. Re-attach the hood,
and run the treadmill for a few minutes to check for a correct speed reading.
23
57
1/8”
20
9
41
Top
View
8
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD FROM THE FRONT OF THE
TREADMILL. Using the allen wrench, turn both rear
roller adjustment bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
b
3”–4”
Rear Roller Adjustment Bolts
c. If the walking belt still slows, please call our Customer Service Department, toll-free.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key and
UNPLUG THE POWER CORD FROM THE FRONT OF
THE TREADMILL. If the walking belt has shifted to the
left, use the allen wrench to turn the left rear roller bolt
clockwise 1/2 of a turn; if the walking belt has shifted to
the right, turn the bolt counterclockwise 1/2 of a turn. Be
careful not to overtighten the walking belt. Plug in the
power cord, insert the key and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove the
key and UNPLUG THE POWER CORD FROM THE
FRONT OF THE TREADMILL. Using the allen wrench,
turn both rear roller bolts clockwise, 1/4 of a turn. When
the walking belt is correctly tightened, you should be able
to lift each side of the walking belt 3 to 4 inches off the
walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key and carefully
walk on the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
a
b
PROBLEM: The incline of the treadmill does not change correctly or does not change when iFIT.com
CDs and videos are played
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline.
24
CONDITIONING GUIDELINES
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
To measure your heart rate during exercise, use the
pulse sensor on the console.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
25
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
1
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
26
5
NOTES
27
PART LIST—Model Nos. HGTL09130M/HGTL09130N
R0703A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key
No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
3
2
2
8
10
4
1
1
8
1
2
4
1
1
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
1
1
2
1
1
4
1
1
11
1
1
4
1
1
2
4
2
1
5
1
2
37
38
39
40
41
42
43
44
45
46
47
1
18
1
2
10
1
1
1
1
1
1
Description
Motor Hood
Tinnerman Clip
Hood Cover
Belt Guide
Belt Guide Screw
Platform Washer
Platform Bolt (Rear)
Front Roller/Pulley
Magnet
Platform Nut
Pivot Bracket
Spacer
Cage Nut
Pivot Washer (Right)
Platform Pivot
Bolt (Right)
Motor Belt
Incline Frame
Belly Pan Bolt
Wire Tie Clamp
Reed Switch
Motor Bolt
Motor Tension Washer
Motor Tension Bolt
Electronics Screw
Controller
Circuit Board
Plastic Stand-off
Electronics Bracket
Front Roller Bolt
Pulse Bar Bolt
Handrail Endcap
Handrail Pivot Bolt
Latch Assembly
Wire Tie
Latch Spacer
Upright Bushing
(Inside)
Pulse Bar
Screw
Handrail
Front Wheel Nut
1/2” Screw
Incline Motor
Console Base
Console Insert
Book Lens
Book Rack
Console Back
Key
No. Qty.
48
49*
1
2
50
51
52
53
54
55
56
57
58
59
60
61
62
63
1
1
1
2
2
1
1
2
2
2
1
8
2
1
64
65
66
67
68
69
70
71
72
1
1
4
13
2
2
2
4
3
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
2
7
1
1
1
3
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
Description
Key/Clip
Extension Leg
Assembly
Upright Ground Wire
Console Ground Wire
Upright Wire Harness
Handrail Pivot Nut
Grommet
Console Latch
iFit Wire
Front Wheel
Front Wheel Bolt
Front Wheel Cover
Wheel Bracket (Right)
Front Wheel Screw
Incline Pivot Bolt
Incline Motor
Bolt (Long)
Stop Bracket
Console/Pulse Bar Wire
Base Pad
3/4” Screw
Wheel Nut
Upright Base Endcap
Extension Leg
Bolt
Wheel Bolt/
Incline Motor Bolt
Wheel
Nut
Wheel Bracket (Left)
Plastic Tie
Tie Block
Long Belly Pan Screw
Belly Pan
Hood Screw
Pivot Washer (Left)
IFIT Wire Nut
Breaker Nut
Receptacle
Circuit Breaker
Belly Pan Plug
On/Off Switch
iFIT Wire
Allen Wrench
Foot Grip (Right)
Walking Belt
Foot Grip (Left)
Walking Platform
Key
No. Qty.
94
95
96
97
98
99
100
101
102
103
1
1
2
1
2
2
2
2
2
2
104
105
106
107
108
109
110*
111
112
113
114
115
2
1
1
1
1
1
1
1
1
2
1
1
116
1
117
118
119
120
121
122
123
124
#
#
#
#
#
#
#
#
#
#
4
1
2
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
Description
Latch Plate
Latch Warning Decal
Endcap Spacer
Left Endcap
Rear Wheel Bolt
Rear Roller Washer
Rear Roller Adj. Bolt
Roller Star Washer
Rear Wheel
Upright Bushing
(Outside)
Rear Spring
Roller Guard (Left)
Roller Guard (Right)
Rear Endcap (Right)
Rear Roller
Upright Base
Motor Assembly
Jack
Key Holder
Static Decal
12” Ground Wire
Incline Motor
Bolt (Short)
Platform Pivot
Bolt (Left)
Platform Bolt (Front)
Lift Frame Ground Wire
Spring Washer
Motor
Flywheel
Motor Controller Wire
Treadmill Power Cord
Warning Decal
4” Black Wire, 2F
4” Black Wire, M/F
14” Blue Wire, 2F
4” Blue Wire, 2F
14” White Wire, 2F
10” White Wire, 2F
12” Green Wire, F/Ring
8” Green Wire, F/Ring
8” Red Wire, M/F
User's Manual
# These parts are not illustrated
* Includes all parts shown in the
box
100
99
101
98
102
97
96
89
100
68
56
95
6
7
99
101
104
2
68
102
106
10
6
1
107
105
94
5
96
111
104
98
108
92
6
10
6
93
3
7
4
5
2
91
34
123
19
6
117
118
90
88
8
80
16
17
9
18
6
116
121
74
41
81
13
21
5
82
78
4
117
12
120
78 86 85
6
87
10
20
24
2
83
78
40
28
80
79
77
12
49*
71
75
24
31
6
10
119
29
58
57
76
84 113
59
11
23
18
110*
13
74
22
25
73
72
67
69
14
67
33
74
70
67
66
109
35
103
39
124
40
15
32
30
27
26
EXPLODED DRAWING—Model Nos. HGTL09130M/HGTL09130N
71
74
40
114
31
72 67
70
67
66
72
31
66
74
64
71
74
10
124
54
36
66
67
69
62
32
52
67
40
38
41
38
46
60
103
38
38
112
45
38
30
42
54
38
74
41
44
5
50
38
41
38 41
43
122
38
51
52
10
38
38
49* 73
74
115
62
36
37
65
R0703A
55
57
113
47
41
38
119
48
38
38
58
38
59
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
• the MODEL NUMBER of the product (HGTL09130M or HGTL09130N)
• the NAME OF THE PRODUCT (IMAGE® EXECUTIVE 2002 treadmill)
• the SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
• the KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST and the EXPLODED DRAWING
attached in the center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of one (1) year from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used for commercial or rental purposes; or products used as store display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to
state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 198718 R0703A
Printed in USA © 2003 ICON Health & Fitness, Inc.

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project