Casio | Weather Radio ID-13 | User manual | Casio Weather Radio ID-13 User manual

Casio Weather Radio ID-13 User manual
• A sticker is affixed to the display of this clock when you purchase it. Be sure to remove the sticker before using
the clock.
• Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the
PM indicator
Current time
(Hour, minutes, seconds)
DATE (month - date)
Day of the week
Current Temperature
Current Humidity
1 Time Set buttons
Use these buttons to set the current time.
2 SET button
Use this button when setting the current time.
3 RESET button
Press to reset the clock after replacing batteries.
4 °C/°F button
Push the °C/°F button to select either Celsius (°C) or Fahrenheit (°F).
1 cm
2) to cycle through the setting screens as shown below.
1. Press the SET button (2
• A built-in sensor measures temperature and shows the measured value on the display. The readout from the
temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F).
• The temperature display shows “LO” for temperatures below –50°C (–58°F) and “HI” for temperatures above
70°C (158°F).
• Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such
readings are actually outside the guaranteed temperature range of this clock.
Normal Timekeeping Screen
Switching between Celsius and Fahrenheit
4) to select either Celsius (°C) or Fahrenheit (°F).
• Push the °C/°F button (4
• A built-in sensor measures humidity and shows the measured value on the display.
• The humidity display shows “LO” for humidity below 10% and “HI” for humidity above 95%.
Year Setting Screen
12-hour/24-hour Timekeeping Screen
Replace batteries whenever the display of the clock becomes dim and difficult to read.
1. Pressing down lightly on the battery compartment cover, slide it downwards and remove it.
2. Remove both old batteries.
3. Load new batteries. Make sure that their positive (+) and negative (–) ends face in the correct directions. If you
load batteries incorrectly, they can burst and damage the clock.
4. Replace the battery compartment cover.
3). Be sure to press the RESET button (3
3) after replacing batteries.
5. Press the RESET button (3
Battery precautions
Month and Day Setting Screen
Time Setting Screen
Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.
Replace the batteries at least once a year, even if the current batteries are working properly.
Never charge the batteries that come with the clock.
Should the batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto
your skin.
• The batteries that come with the clock lose some of their power during transport and storage.
• Never mix old and new batteries, or batteries of different brands.
1) to change the digits that are flashing.
2. While the screen you want is on the display, use the Time Set buttons (1
Press + to increase
the flashing digits.
Press – to decrease
the flashing digits.
• Holding down + or – changes the flashing digits at high speed.
• You can set the year in the range of 2000 to 2039. The day of the week is set automatically in accordance with
the date setting.
• Pressing + or – while the Time Setting Screen is on the display causes the seconds count to be reset to 00.
• Each press of + or – while the 12-hour/24-hour Timekeeping Screen is on the display toggles between 12-hour
and 24-hour timekeeping.
2) to display the Normal Timekeeping Screen.
3. After making the settings you want, use the SET button (2
• The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display
for about three minutes without performing any operation.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF