Casio Clock DQS-20 User manual

Casio Clock DQS-20 User manual
MA0212-A
USER’S GUIDE DQS-20
GENERAL GUIDE
1 SNOOZE button
Pressing this button while the alarm is sounding stops the alarm.
2 LIGHT button
Press to turn on the backlight.
3 Alarm Time Set buttons
Use these buttons to set the alarm time or current time.
4 SET button
Use this button when setting the current time.
5 RESET button
Press to reset the clock after replacing the battery.
6 Alarm Switch
Use this switch to turn the alarm on and off, and to turn on the snooze alarm.
7 Solar panel
8 Insulation sheet
Pull out the insulation sheet in the direction indicated by the arrow before using the clock.
5).
After removing the insulation sheet, press the RESET button (5
SETTING THE TIME
4) to cycle through the setting screens as shown below.
1. Press the SET button (4
Normal Timekeeping Screen
• A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the
clock.
• Before using this clock for the first time, note the insulation sheet sticking out of the battery compartment. Pull out
the insulation sheet in the direction indicated by the arrow before using the clock.
5).
• After removing the insulation sheet, press the RESET button (5
• Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the
illustration.
Alarm Off
DATE (month - date)
PM indicator
Day of the week
Current time
(Hour, minutes, seconds)
Year Setting Screen
12-hour/24-hour Timekeeping Screen
Month and Day Setting Screen
Time Setting Screen
Alarm On
Alarm time
Snooze on indicator
Alarm on indicator
1
USER’S GUIDE DQS-20
2. While the screen you want is on the display, use the Alarm Time Set buttons (3
3) to change the digits that are
flashing.
Press – to decrease
the flashing digits.
Press + to increase
the flashing digits.
USING THE LIGHT
2) turns on the light and illuminates the display for easy reading in the dark.
Pressing the LIGHT button (2
Important!
• Overuse of the light can shorten battery life.
BATTERY REPLACEMENT
• Holding down + or – changes the flashing digits at high speed.
• You can set the year in the range of 2000 to 2039. The day of the week is set automatically in accordance with
the date setting.
• Pressing + or – while the Time Setting Screen is on the display causes the seconds count to be reset to 00.
• Each press of + or – while the 12-hour/24-hour Timekeeping Screen is on the display toggles between 12-hour
and 24-hour timekeeping.
4) to display the Normal Timekeeping Screen.
3. After making the settings you want, use the SET button (4
• The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display
for about three minutes without performing any operation.
Replace the battery whenever the display of the clock becomes dim and difficult to read.
• Always have the battery replaced at your nearest dealer.
USING THE ALARM
The alarm sounds and the backlight turns on when the alarm time you set is reached. You can also use the Alarm
6) to select the snooze alarm feature.
Switch (6
Setting the Alarm Time
3) to set the alarm time.
Use the Alarm Time Set buttons (3
3) causes the alarm time to appear in place of the date on the display.
Pressing an Alarm Time Set button (3
Press to change the alarm
time setting (+).
Press to change the alarm
time setting (–).
Alarm Time Set buttons
• Holding down + or – changes the digits at high speed.
Turning the Alarm On and Off
6) on the side of the clock to turn the alarm on and off, and to select the snooze feature.
Use the Alarm Switch (6
Alarm Switch Setting
SNOOZE ON
( Zz
)
ALARM ON
(
OFF
)
Description
The alarm sounds at the preset time for one
minute, and seven more times every five
minutes thereafter. Even if you stop the alarm
1),
sound by pressing the SNOOZE button (1
the alarm operation is performed again five
minutes later.
• The indicator Zz flashes on the display to
indicate that the snooze feature is activated.
The alarm sounds at the preset time for one
minute.
The alarm does not sound.
• The alarm time appears in place of the date on the display whenever the alarm switch is set to ON or SNOOZE.
• The backlight also turns on for the first four seconds that the alarm sounds.
• The alarm sound changes over five levels as it sounds.
Stopping the Alarm
1) to stop it. When the snooze feature is turned on, the
• When alarm is sounding, press the SNOOZE button (1
alarm will sound again in about five minutes.
6) to OFF.
• To turn off the snooze feature, slide the Alarm Switch (6
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement