Magnavox DVD VCR Combo 1VMN26713A Owner's Manual

Introduction
Owner's Manual
Playback
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
Recording
NEED HELP FAST?
READ YOUR QUICK GUIDE AND/OR OWNER'S MANUAL FIRST FOR QUICK TIPS THAT MAKE
USING YOUR MAGNAVOX PRODUCT MORE ENJOYABLE.
IF YOU HAVE READ YOUR INSTRUCTIONS AND STILL NEED ASSISTANCE,
YOU MAY ACCESS OUR ONLINE HELP AT WWW.MAGNAVOX.COM/SUPPORT
OR CALL 1-800-605-8610 WHILE WITH YOUR PRODUCT.
Basic Setup
THANK YOU FOR CHOOSING MAGNAVOX.
Connections
ZV457MG9 A
DIGITAL VIDEO DISC RECORDER & VIDEO CASSETTE RECORDER
WITH DIGITAL TUNER
Editing
Function Setup
VCR Functions
Others
Español
© 2010 Funai Electric Co., Ltd.
SAFETY INFORMATION
The model and serial numbers of this unit may be found on the cabinet.
You should record and retain those numbers for future reference.
Model No.:
Serial No.:
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The important note is located on the rear or bottom of the cabinet.
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may
cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the
authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Disconnect the mains plug to shut off when find trouble or not in use. The mains plug shall remain readily operable.
2
EN
Introduction
SAFETY INFORMATION
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
WARNING: Batteries (Battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire, or the like.
Connections
LASER SAFETY
This apparatus employs a laser. Only a qualified service person should remove the cover or attempt to service this
apparatus, due to possible eye injury.
CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION: Visible and invisible laser radiation when open and interlock defeated. Do not stare into beam.
LOCATION: Inside, near the deck mechanism.
Basic Setup
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates
copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this
copyright protection technology must be authorized by Macrovision, and is intended for home and other limited
viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
Recording
Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing
or climbing on it. A falling unit can cause serious injury or even death.
To Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC outlet. Grasp it by the plug.
• Do not put your fingers or objects into the unit.
Playback
Location and Handling
Editing
• Do not install the unit in direct sunlight, near strong magnetic fields, or in a place subject to dust or strong vibration.
• Avoid a place with drastic temperature changes.
• Install the unit in a horizontal and stable position. Do not place anything directly on top or bottom of the unit.
Depending on your external devices, noise or disturbance of the picture and/or sound may be generated if the unit is
placed too close to them. In this case, please ensure enough space between the external devices and the unit.
• Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.
• Be sure to remove the disc and unplug the AC power cord from the outlet before carrying the unit.
Dew Condensation Warning
Function Setup
• Dew condensation may form inside the unit in the following conditions. If so, do not use this unit at least for a few
hours until its inside gets dry.
- The unit is moved from a cold place to a warm place.
- Under conditions of high humidity.
- After heating a cold room.
Note about Recycling
VCR Functions
• This unit’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
• Batteries should never be thrown away or incinerated but disposed of in accordance with your local
regulations concerning chemical wastes.
Notice for Progressive Scan Output
• Consumers should note that not all high definition television sets are fully compatible with this product and may
cause artifacts to be displayed in the picture. In case of picture problems with 525(480) progressive scan output,
it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions
regarding your TV set compatibility with this 525p(480p) DVD player, please contact our customer service center.
Others
Español
EN
3
SAFETY INFORMATION
Supplied Accessories
remote control (NB884UD) with batteries AA(1.5 V)x2
Cleaning discs
• When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center to out. Do not
wipe in a circular motion.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for analog
records.
Cleaning the disc lens
RF coaxial cable (WPZ0901TM005/WPZ0901TM002)
• If this unit still does not perform properly
although you refer to the relevant sections and to
“TROUBLESHOOTING” in this owner's manual, the laser
optical pickup unit may be dirty. Consult your dealer
or an Authorized Service Center for inspection and
cleaning of the laser optical pickup unit.
Disc handling
RCA audio/video cables (WPZ0102TM018/WPZ0102LTE01)
• Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
• Always store the disc in its protective case when it is
not used.
Auto head cleaning
owner's manual (1VMN26713A)
• Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted
while the TV program reception is clear. Dirt accumulated
on the video heads after a long period of use, or the
usage of rental or worn tapes can cause this problem. If
a streaky or snowy picture appears during playback, the
video heads in your unit may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a
good quality VHS video head cleaner.
2. If a video head cleaner does not solve the problem, please
consult your dealer or an Authorized Service Center.
Note
quick guide (1VMN26714)
• Remember to read the instructions along with the
video head cleaner before use.
• Clean video heads only when problems occur.
IR signal check
Maintenance
Servicing
• Please refer to relevant topics on “TROUBLESHOOTING”
on pages 97-100 before returning the product.
• If this unit becomes inoperative, do not try to correct
the problem by yourself. There are no user-serviceable
parts inside. Turn the unit to the standby mode, unplug
the power plug and please call our help line mentioned
on the front page to locate an Authorized Service
Center.
Cleaning the cabinet
• Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution containing
alcohol, spirits, ammonia or abrasive.
4
EN
If the remote control does not work properly, you can test
if the remote control sends out the infrared signal with a
digital camera (including built-in camera of cellular phone).
It will help to define the cause of malfunction.
With a digital camera (including built-in
camera of cellular phone):
Direct a digital camera to remote control, press
and hold a button on remote control. If infrared
light appears through digital camera, the
remote control is working.
Introduction
SAFETY INFORMATION
Trademark Information
Connections
is trademark of Eastman Kodak Company.
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
Basic Setup
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
Recording
Dolby Digital Recording
“Dolby® Digital Recording enables consumers to record
high-quality video with stereo sound on recordable
DVD discs. The technology, when utilized instead of
PCM recording, also saves recordable disc space, allowing for higher video resolution or extended recording
time on each DVD. DVDs created using Dolby Digital
Recording will play back on all DVD-video players.”
Note: This is true when the players are compatible with
actual recordable DVD discs.
Playback
Editing
Function Setup
VCR Functions
© 2010 Funai Electric Co., Ltd.
Others
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed,
downloaded or stored in any storage medium, in any form or for any purpose without the express prior written
consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is
strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content
herein without the obligation to notify any person or organization of such changes.
EN
Español
with the
design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without
the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective
owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or
right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is
strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.
5
CONTENTS
Introduction
Recording
SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Symbols Used in this Owner’s Manual . . . . . . . . . . . . . . .9
FUNCTIONAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . 10
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Front Panel Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
INFORMATION ON DVD RECORDING . . . . . . . . . . . . .
BEFORE RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Make Recording Compatible . . . . . . . . . . . . . . . . . . . . . .
Setting for Auto Chapter . . . . . . . . . . . . . . . . . . . . . . . . . .
Recording the DTV Closed Caption . . . . . . . . . . . . . . . .
BASIC RECORDING &
ONE-TOUCH TIMER RECORDING . . . . . . . . . . . . . . . . .
TIMER RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hints for Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . .
OVERWRITING UNNECESSARY TITLE . . . . . . . . . . . . .
Overwriting from the Beginning of the Title. . . . . . . .
Overwriting in the Middle of the Title . . . . . . . . . . . . . .
Hints for Overwriting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SETTINGS FOR AN EXTERNAL DEVICE . . . . . . . . . . . .
Connection to an External Device. . . . . . . . . . . . . . . . . .
Recording from an External Device . . . . . . . . . . . . . . . .
BI-DIRECTIONAL DUBBING . . . . . . . . . . . . . . . . . . . . . .
SETTING A DISC TO PROTECT . . . . . . . . . . . . . . . . . . . .
PLAYING THE DISCS ON OTHER DVD PLAYERS . . . .
Finalizing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Finalizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connections
CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antenna Connection (Required) . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to a TV with an HDMI™
Compatible Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting to a TV Using
Component Video Out Jacks . . . . . . . . . . . . . . . . . . . . . .
Connecting to a TV Using the S-Video Out Jack . . . .
Connecting to a TV Using Audio / Video Jacks. . . . . .
Connecting to a Cable / Satellite Box . . . . . . . . . . . . . .
Connecting to a TV without Audio / Video Jacks . . .
Digital Audio Connection. . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
15
16
17
17
18
19
20
21
Basic Setup
BEFORE YOU START . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Finding the Viewing Channel on Your TV . . . . . . . . . .
Guide to On-Screen Display / Menu. . . . . . . . . . . . . . . .
Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching DVD / VCR Mode. . . . . . . . . . . . . . . . . . . . . . . .
How to Insert a Disc / Cassette Tape . . . . . . . . . . . . . . .
INITIAL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHANNEL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding / Deleting Channels . . . . . . . . . . . . . . . . . . . . . . .
SETTING THE CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Clock Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Daylight Saving Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TUNER SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching Analog Mode / Digital Mode . . . . . . . . . . . .
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting TV Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DTV Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Closed Caption Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
EN
22
22
23
25
26
26
27
28
28
29
30
30
32
32
33
33
33
34
36
37
39
40
40
40
40
41
43
46
47
47
47
48
49
49
50
51
53
54
54
55
Editing
56
58
58
59
70
70
70
71
71
72
73
74
76
77
78
79
80
81
Recording
Function Setup
LIST OF SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SETUPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
82
85
85
88
91
92
93
Playback
VCR Functions
94
94
94
94
95
95
96
96
Function Setup
VCR FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information on VCR Functions . . . . . . . . . . . . . . . . . . . . .
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
One-touch Timer Recording (OTR) . . . . . . . . . . . . . . . . .
Index Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing
60
61
61
62
62
62
62
62
63
63
63
64
64
65
65
65
66
66
66
67
68
68
68
69
69
69
INFORMATION ON DISC EDITING. . . . . . . . . . . . . . . . .
Guide to a Title List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EDITING DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting a Title. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Putting Names on Titles . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Chapter Marks. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clearing Chapter Marks . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hiding Chapters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Pictures for Thumbnails. . . . . . . . . . . . . . . . . . . .
Dividing a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Putting Name on Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erasing Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making Edits Compatible . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Setup
INFORMATION ON PLAYBACK . . . . . . . . . . . . . . . . . . .
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Playback from the Title List . . . . . . . . . . . . . . . . . . . . . . . .
Playing Back an Audio CD and a CD-RW / -R
with MP3 / JPEG Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Title / Disc Menu . . . . . . . . . . . . . . . . . . . . . . . .
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resume Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fast Forward / Fast Reverse Playback . . . . . . . . . . . . . .
Skipping TV Commercials During Playback. . . . . . . . .
Rapid Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step by Step Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slow Forward / Slow Reverse Playback. . . . . . . . . . . . .
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Marker Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slide Show . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Program Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Title / Chapter Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Track Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SELECTING THE FORMAT OF AUDIO AND VIDEO . .
Switching Subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching Audio Soundtrack . . . . . . . . . . . . . . . . . . . . . .
Switching Virtual Surround System . . . . . . . . . . . . . . . .
Switching Camera Angles . . . . . . . . . . . . . . . . . . . . . . . . .
Reducing Block Noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connections
Playback
Introduction
CONTENTS
Others
VCR Functions
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
LANGUAGE CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Español
ESPAÑOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . Back cover
Others
Español
EN
7
FEATURES
This unit not only plays back DVD, CD and VCR but also offers features for you to record on DVD and edit them after
that. The following features are offered with this unit.
Recording
This unit is compatible with DVD+RW/DVD-RW, which
are rewritable repeatedly and DVD+R/DVD-R, which are
available for recording once. Even if you choose DVDRW/DVD-R, these discs will automatically be recorded in
the DVD+VR mode. Also, this unit allows you to record
to the cassette tape. You can choose either one for your
convenience.
DVD
VCR
Up to 12 program recording:
You can program the unit to record up to 12 programs
within a one-month period. Daily or weekly program
recordings are also available.
One-touch timer recording (OTR):
You can easily set a recording time as you prefer. Every
time [REC] is pressed during recording, the recording
time will be increased by 30 minutes up to 6 hours for
DVD, and 8 hours for VCR. The recording automatically
stops when the recording time you set is reached or the
disc is full.
Dubbing mode:
You can copy a DVD to a cassette tape or copy a cassette
tape to a DVD. This function will be possible only if the
DVD or a cassette tape is not copy protected.
You cannot record on a cassette tape when its erase-protection tab is removed.
Left channel stereo recording:
This unit can record the sound of the left channel monaural input as left and right channels automatically.
VCR
Quick search for what you want to watch:
You can easily find the part you want to watch using the
index search/time search functions. An index mark will be
assigned at the beginning of each recording you make.
For time search function, you can go to a specific point on
a cassette tape by entering the exact amount of time you
wish to skip.
Editing
DVD
Deleting titles:
You can delete titles which you do not need anymore.
Putting names on titles:
You can put your favorite names on titles.
Setting / clearing chapter marks:
You can set / clear chapter marks on titles.
Hiding chapters:
To keep others from playing back some chapters without
permission, you can hide chapters.
Setting pictures for thumbnails:
You can change pictures for thumbnails.
Dividing titles (DVD+RW/DVD-RW only):
You can divide a title into 2 or more.
Putting name on disc:
You can put your favorite disc name.
Compatibility
DVD
Automatic chapter mark setting:
Chapter marks will be put on recordings as you set before
attempting to record.
Automatic title list making:
The unit makes a title list with the index automatically.
Playback
DVD
Theater surround sound in your home:
When connecting the unit to an amplifier or a decoder
which is compatible with Dolby Digital, you can experience the theater surround sound from discs with surround sound system.
Quick search for what you want to watch:
You can easily find the part you want to watch using the
search function. Search for a desired point on a disc by
title, chapter or time.
Virtual surround system:
You can enjoy stereophonic space through your existing
2 channel stereo system.
Playing back MP3 / JPEG / Kodak Picture CD files:
You can enjoy MP3 / JPEG / Kodak Picture CD files which
are recorded on CD-RW/-R.
8
EN
DVD
Available for playing back discs on a regular DVD
player:
Recorded discs can be played back on regular DVD
players, including computer DVD drives compatible
with DVD-video playback. Although DVD+R are playable
on other units without finalization in most cases, it
is recommended to finalize in order to stabilize the
performance. For DVD-RW/-R, you need to finalize the
recorded discs to play back on other DVD players.
Others
DVD
VCR
Progressive scan system
Unlike conventional interlace scanning, the progressive
scan system provides less flickering and images in higher
resolution than that of traditional television signals.
HDMI (High-Definition Multimedia Interface)
You can enjoy clearer audio/video output when connecting
this unit to a display device with an HDMI-compatible port.
Introduction
FEATURES
Symbols Used in this Owner’s Manual
Connections
To specify for what disc type each function is, we put
the following symbols at the beginning of each item to
operate.
* DVD-RW/-R recorded in VR mode or non compatible
recording format are not playable.
* DVD-RW recorded in the mode other than +VR is not
recordable on this unit unless you erase all contents in
the disc (refer to page 80).
* DVD-R recorded in the mode other than +VR is not
recordable on this unit.
Basic Setup
Symbol Description
For Recording, Playing Back, and Editing
Description refers to DVD+RW
Description refers to DVD+R
Recording
Description refers to DVD-RW
Description refers to DVD-R
For Recording and Playing Back
Description refers to VHS tapes
Use only cassettes marked VHS (
)
Playback
For Playback only
Description refers to DVD-video
Description refers to audio CD
Description refers to video CD with PBC function
Editing
Description refers to video CD without PBC
function
Description refers to CD-RW/-R with MP3 files
Description refers to CD-RW/-R with JPEG files
(Kodak Picture CD files included)
Function Setup
If you do not find any of the symbols listed above under the
function heading, the operation is applicable to all media.
VCR Functions
Others
Español
EN
9
FUNCTIONAL OVERVIEW
Front Panel
1
2*
3
ZV457MG9
23 22
21 2019 18 17 16
15
14 13 12 11 10 9 8* 7 6 5
4
(*) The unit can also be turned on by pressing these buttons or inserting a cassette tape.
1. Cassette compartment (VCR)
Insert a cassette tape here.
2. A OPEN/CLOSE button (DVD)*
Press to open or close the disc tray.
3. Disc tray (DVD)
Place a disc when it is open.
4. AUDIO input jacks (L2) (DVD/VCR)
Use to connect external device with an RCA audio
cable.
5. VIDEO input jack (L2) (DVD/VCR)
Use to connect external device with an RCA video
cable.
6. S-VIDEO input jack (L2) (DVD/VCR)
Use to connect the S-video output of external device
with an S-video cable.
7. I RECORD button (DVD)
• Press once to start a recording.
• Press repeatedly to start the one-touch timer
recording.
8. B PLAY button (DVD)*
Press to start or resume playback.
9. C STOP button (DVD)
Press to stop playback or recording.
Press to stop the proceeding timer recording in DVD.
10. DVD indicator
Lights up when the DVD output mode is selected.
11. SOURCE button (DVD/VCR)
Press to select the component you wish to operate.
12. VCR indicator
Lights up when the VCR output mode is selected.
13. D.DUBBING button (DVD/VCR)
Press to start VCR to DVD (DVD to VCR) duplication
which you set in the main menu.
10
EN
14. CHANNEL L / K buttons (DVD/VCR)
Press to change the channel up and down.
15. Display (DVD/VCR)
Refer to “Front Panel Display” on page 14.
16. Infrared sensor window (DVD/VCR)
Receive signals from your remote control so that you
can control the unit from a distance.
17. I RECORD button (VCR)
Press once to start a recording. Press repeatedly to
start the one-touch timer recording.
18. B PLAY button (VCR)
Press to start playback.
19. C A STOP/EJECT button (VCR)
• Press to remove the cassette tape from the cassette
compartment.
• Press to stop cassette tape playback or recording.
• Press to stop the proceeding timer recording in VCR.
20. D F.FWD button (VCR)
Press to rapidly advance the cassette tape, or view the
picture rapidly in forward during playback (forward
search).
21. E REW button (VCR)
Press to rewind the cassette tape, or to view the
picture rapidly in reverse during playback (rewind
search).
22. y STANDBY-ON button (DVD/VCR)
Press to turn on the unit, or to turn the unit to the
standby mode. (To completely shut down the unit,
you must unplug the AC power cord.)
23.POWER-ON indicator (DVD/VCR)
Red LED lights up when power is on.
Introduction
FUNCTIONAL OVERVIEW
Rear Panel
1
2
3
Connections
HDMI OUT
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
Y
IN --- AUDIO --- OUT
L
L
R
R
IN
ANTENNA
L
OUT
PB
/CB
COAXIAL
IN ---VIDEO --- OUT
R
5 11 10 9 8 7 6 5
4
Playback
9. S-VIDEO IN jack (L1)
Use to connect the S-video output of external device
with an S-video cable.
10. COMPONENT VIDEO OUT jacks
Use to connect a TV monitor with component video
inputs with a component video cable.
11. S-VIDEO OUT jack
Use to connect the S-video input of a TV monitor, AV
receiver or other device with an S-video cable.
12. COAXIAL DIGITAL AUDIO OUT jack
Use to connect an AV receiver, Dolby Digital decoder
or other device with a digital audio coaxial input jack
with a digital audio coaxial cable.
Recording
Note
• Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
• This unit does not have the RF modulator.
Caution on using S-video, component, or HDMI
connection for VCR:
• Only the playback video/audio are available with
these connections.
Editing
Function Setup
1. AC Power Cord
• Connect to a standard AC outlet to supply power to this
unit.
• Unplug this cord from the AC outlet to completely shut
down the unit.
2. HDMI OUT jack
Use an HDMI cable to connect to a display with an
HDMI compatible port.
3. ANTENNA OUT jack
Use to connect an RF coaxial cable to pass the signal
from the ANTENNA IN to your TV monitor.
4. ANTENNA IN jack
Use to connect an antenna.
5. AUDIO OUT jacks
Use to connect a TV monitor, AV receiver or other
device with an RCA audio cable.
6. VIDEO OUT jack
Use to connect a TV monitor, AV receiver or other
device with an RCA video cable.
7. VIDEO IN jack (L1)
Use to connect external device with an RCA video
cable.
8. AUDIO IN jacks (L1)
Use to connect external device with an RCA audio
cable.
PR
/CR
Basic Setup
12
IN
VCR Functions
Others
Español
EN
11
FUNCTIONAL OVERVIEW
Remote Control
Installing the Batteries in the Remote Control
Install the batteries (AAx2) matching the polarity
indicated inside battery compartment of the remote
control.
1
Open the cover.
2
Insert batteries.
Make sure to match + and - on the batteries to
the marks indicated in the battery compartment.
3
Using a Remote Control
Keep in mind the following when using the remote
control:
• Make sure that there are no obstacles between the remote
control and the infrared sensor window on the unit.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the infrared
sensor window of the unit.
• Remote control for different devices can interfere with
each other. Avoid using remote control for other device
located close to the unit.
• Replace the batteries when you notice a fall off in the
operating range of the remote control.
• The maximum operable ranges from the unit are as
follows.
- Line of sight: approx. 23 feet (7m)
- Either side of the center:
approx. 16 feet (5m) within 30°
- Above: approx. 16 feet (5m) within 15°
- Below: approx. 10 feet (3m) within 30°
16 feet (5m)
30˚
23 feet (7m)
16 feet (5m)
30˚
Close the cover.
2
16
17
3
18
1
19
4
5
6
7
Note
Incorrect use of batteries can result in hazards such as
leakage and bursting. Please observe the following:
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together.
Although they may look similar, different batteries
may have different voltages.
• Make sure that the + and - ends of each battery
match the indications in the battery compartment.
• Remove batteries from battery compartment that is
not going to be used for a month or more.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country
or area.
• Do not recharge, short-circuit, heat, burn or
disassemble batteries.
12
EN
9
8
10
11
12
1413
15
21
22
20
23
24
26
27
25
28
29
3130
32
34
33
Basic Setup
Recording
Playback
Editing
Function Setup
VCR Functions
Others
Note
• If you turn this unit to the standby mode, [OPEN/CLOSE
A] on the remote control is not available.
Be sure to use [A OPEN/CLOSE] or [C A STOP/EJECT]
on the unit.
EN
13
Español
DVD mode:
• Press to change the channel up and down.
VCR mode:
• Press to change the channel up and down.
• Press to adjust the tracking during playback or in slow
motion of the cassette tape.
• While playback is in still mode, you can adjust the
picture blurred vertically.
19. HDMI button (DVD)
• Press to set the HDMI connector’s video signal output mode.
20. CLEAR button (DVD/VCR)
DVD mode:
• Press to clear the password once entered or to cancel the programming for CD or to clear the selected
marker number, etc.
VCR mode:
• Press to reset the tape counter.
21. AUDIO button (DVD/VCR)
DTV mode:
• Press to switch the audio language for digital TV.
DVD mode:
• Press to display the audio menu during playback.
VCR mode:
• During playback of a Hi-Fi videotape, press to
change the audio out setting.
22. TIMER button (DVD/VCR)
• Press to display the timer programming list.
23. TITLE button (DVD)
• Press to display the title list.
24. Cursor K / L / { / B buttons (DVD/VCR)
• Press to select items or settings.
25. RETURN button (DVD/VCR)
• Press to return to the previously displayed menu screen.
26. DVD button
• Press to select the DVD output mode.
27. PLAY B button (DVD/VCR)
• Press to start playback or resume playback.
28. NEXT G button (DVD)
• During playback, press to skip to the next chapter,
track or file.
• When playback is in pause, press repeatedly to forward the playback step by step.
29. STOP C button (DVD/VCR)
• Press to stop playback or recording.
DVD mode:
• Press to exit from the title list.
30. FFW D button (DVD/VCR)
DVD mode:
• During playback, press to fast forward playback.
• When playback is paused, press to slow forward playback.
VCR mode:
• During playback, press to rapidly advance the
cassette tape or view the picture rapidly in forward.
• When playback is paused, press to view the cassette
tape in slow motion.
31. RAPID PLAY button (DVD)
• During playback, press to play back in a slightly
faster/slower mode with keeping the audio quality.
32. SEARCH button (VCR)
• Press to call up the index or time search menu.
33. TIMER SET button (DVD/VCR)
• Press to set the unit in the timer standby mode. In
the timer standby mode, press to cancel the mode
and to turn the unit on.
34. REC button (DVD/VCR)
• Press once to start a recording.
• Press repeatedly to start the one-touch timer recording.
Connections
1. DTV/TV button (DVD/VCR)
• Press to switch between digital TV (DTV) mode and
analog TV (TV) mode.
2. STANDBY-ON y button (DVD/VCR)
• Press to turn on the unit, or to turn the unit to the
standby mode. (To completely shut down the unit,
you must unplug the AC power cord.)
3. Number/Character buttons (DVD/VCR)
• Press to select channel numbers.
• Press to select a title/chapter/track/file on display.
• Press to enter values for the settings in the main menu.
• Press to enter title names.
• Press to start the index/time search in VCR mode.
4. Confirm ( • ) button (DVD/VCR)
Analog mode:
• Press to confirm the channel selection made by
[the Number buttons].
Digital mode:
• Press to confirm the major / minor channel
selection made by [the Number buttons].
5. DISPLAY button (DVD/VCR)
• Press to display the display menu on or off.
6. DISC MENU button (DVD)
• Press to display the disc menu.
7. OK button (DVD/VCR)
• Press to confirm or select menu items.
8. SETUP button (DVD/VCR)
• Press to display the main menu.
• During DVD playback, press and hold for more than
3 seconds to switch the progressive scanning mode
to the interlace mode.
9. VCR button
• Press to select the VCR output mode.
10. PREV H button (DVD)
• During playback, press to return to the beginning of
the current chapter, track or file.
• When playback is in pause, press repeatedly to
reverse the playback step by step.
11. REW E button (DVD/VCR)
DVD mode:
• During playback, press to fast reverse playback.
• When playback is paused, press to slow reverse playback.
VCR mode:
• During playback, press to rewind the cassette tape
or to view the picture rapidly in reverse.
12. CM SKIP button (DVD)
• During playback, press to skip 30 seconds.
13. PAUSE F button (DVD/VCR)
• Press to pause playback or recording.
14. D.DUBBING button (DVD/VCR)
• Press to start VCR to DVD (DVD to VCR) duplication
which you set in the main menu.
15. REC MODE button (DVD/VCR)
• Press repeatedly to switch the recording mode.
16. SOURCE button (DVD/VCR)
• Press to select the appropriate input.
17. OPEN/CLOSE A button (DVD/VCR)
DVD mode:
• Press to open or close the disc tray.
VCR mode:
• Press to remove the cassette tape from the cassette
compartment.
18. CHANNEL / buttons (DVD/VCR)
Introduction
FUNCTIONAL OVERVIEW
FUNCTIONAL OVERVIEW
Front Panel Display
2
1
PM
3
DTV BS CS
DR
CD
VCR
DB HDD
DVD
4
5
1.
PM
: Appears when the timer
programming or OTR has
been set or is proceeding.
: Flashes when all timer
recordings have been finished.
: Appears in the afternoon
with the clock display.
2.
DTV
: Appears when the channel is
in DTV mode.
: Appears when this unit is in
DVD output mode.
: Appears when the timer
recording is proceeding in
DVD.
: Appears when DVD is in the
timer recording standby
mode.
: Flashes when a program
cannot be performed for
some reasons.
DB
: Appears during VCR to DVD
duplication process.
: Appears during DVD to VCR
duplication process.
: Appears during recording
process.
: Flashes when a recording is in
pause.
3. Title / track / file and chapter mark
: Appears when indicating a
title / track / file number.
: Appears when this unit is in
DVD output mode and a disc
is in the unit.
: Appears during duplication
process.
: Appears when indicating a
chapter number.
4. Current status of the unit
: Appears when playback is in
pause, or in step by step
playback.
: Appears when this unit is in
VCR output mode and a
cassette tape is in the unit.
: Appears during duplication
process.
: Appears when playing back a
disc, or a cassette tape.
: Appears during slow forward
/ reverse playback.
DVD
VCR
: Appears when this unit is in
VCR output mode.
: Appears when the timer
recording is proceeding in VCR.
: Appears when VCR is in the
timer recording standby mode.
: Flashes when a program cannot
be performed for some reasons.
5. Displays the following
• Elapsed playback time
• Current title / chapter / track /
file number
• Recording time / remaining time
• Clock
• Selected channel number
• Remaining time for one-touch
timer recording
• Selected HDMI output mode
• VCR tape counter
Display Message
Appears when the disc tray is
opening.
DVD
Appears when HDMI output
mode (480p) is selected.
DVD
Appears when HDMI output
mode (720p) is selected.
Appears when the disc tray is
closing.
DVD
DVD
Appears when a disc is loaded
on the disc tray.
DVD
Appears when HDMI output
mode (1080i) is selected.
DVD
Appears when data is being
recorded on a disc.
DVD
DVD
14
EN
Appears when HDMI output
mode (1080p) is selected.
DVD
Appears when the PBC function
is activated. (Video CD playback
only. Refer to page 57.)
Introduction
CONNECTION
Read this first:
1) Disconnect the AC power cords of the devices from the AC outlet.
2) Make the connection as illustrated below.
3) After making all the connections, connect the AC power cords of the devices.
Connections
• Connect this unit directly to the TV. If the RCA audio/video cables are connected to a VCR, pictures may be
distorted due to the copy protection system.
Antenna Connection (Required)
HDMI OUT
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
Y
Basic Setup
rear of this unit
RF coaxial
cable
IN --- AUDIO --- OUT
L
L
R
R
IN
ANTENNA
L
OUT
PB
/CB
COAXIAL
IN
IN --- VIDEO --- OUT
R
ANT. IN
PR
/CR
This connection is for
TV loop through only
Recording
VHF / UHF
antenna
OUT
IN
ANTENNA
or
RF coaxial cable
Playback
cable TV
company
Choose one of the following connections
depending on the jacks on your TV.
Note
Function Setup
Supplied cables used in this connection are as follows:
• RF coaxial cable x 1
Please purchase the rest of the necessary cables at your local store.
Higher
Quality
HDMI IN
S-VIDEO IN
R
L
AUDIO IN VIDEO IN
page
16
If you are using
cable / satellite box
page
19
page
17
page
17
page
18
If your device has
only an ANT. IN jack
ANT. IN
page
20
EN
Español
Standard
Quality
Refer to
Others
COMPONENT VIDEO IN
VCR Functions
Overview
If Your TV has
Editing
• For your safety and to avoid damage to the device, please unplug the RF coaxial cable from the ANTENNA IN jack before
moving the unit.
• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be
more effective than set-top versions.
• ANTENNA OUT jack is for tuner pass through only. DVD playback through the RF is not possible.
15
CONNECTION
Connecting to a TV with an HDMI™ Compatible Port
• HDMI outputs the video / audio signals without converting to analog signals.
• No audio connection is required.
HDMI IN
HDMI cable
HDMI OUT
rear of this unit
HDMI OUT
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
IN --- AUDIO --- OUT
L
Y
L
IN
ANTENNA
L
OUT
PB
/CB
COAXIAL
IN
R
R
IN --- VIDEO --- OUT
R
PR
/CR
ANT. IN
VHF / UHF
antenna
This connection is for
TV loop through only
RF coaxial
cable
Do not tilt the connector when inserting it into the HDMI jack, and make sure the
shapes of the jack and the connector are matched.
OUT
IN
RF coaxial cable
ANTENNA
or
cable TV
company
Supplied cables used in this connection are as follows:
• RF coaxial cable x 1
Please purchase the rest of the necessary cables at your local store.
HDMI Mode and Actual Output Signals
Press [HDMI] to select the HDMI output mode. The output mode changes as follows every time [HDMI] is pressed.
Front Panel Display
Video Output Signal
480 Progressive
Press [HDMI]
720 Progressive
Press [HDMI]
1080 interlaced
Press [HDMI]
1080 Progressive
Copyright protection system
To play back the digital video images of a DVD via an HDMI
connection, it is necessary that both the player and the
display device (or an AV amplifier) support a copyright
protection system called HDCP (high-bandwidth digital
content protection system). HDCP is copy protection
technology that comprises data encryption and
authentication of the connected AV device. This unit
supports HDCP. Please read the operating instructions of
your display device (or AV amplifier) for more information.
*HDMI: High Definition Multimedia Interface
Press [HDMI]
• The HDMI mode that is not supported by display device will be skipped.
Note
• Some devices with an HDMI input may not operate properly with this unit.
• When using an HDCP-incompatible display device, the image will not be viewed properly.
• Among the devices that support HDMI, some devices can control other devices via the HDMI connector; this unit cannot be
controlled by another device via the HDMI connector.
• The audio signals from the HDMI connector (including the sampling frequency, the number of channels and bit length) may be
limited by the device that is connected.
• Among the monitors that support HDMI, some do not support audio output (for example, projectors). In connections with device
such as this unit, audio signals are not output from the HDMI output connector.
• When this unit’s HDMI connector is connected to a DVI-D compatible monitor (HDCP compatible) with an HDMI-DVI converter cable,
the signals are output in digital RGB.
• When the power failure occurs, or when you unplug the unit, some problems in the HDMI setting might occur. Please check and set
the HDMI setting again.
• HDMI video resolution cannot be changed when the unit is in VCR mode.
16
EN
Introduction
CONNECTION
Connecting to a TV Using Component Video Out Jacks
AUDIO IN
L
RCA component
video cable
AUDIO
OUT
(Green)
Connections
RCA audio cable
R
COMPONENT
VIDEO IN
DVD / VCR
COMPONENT
VIDEO OUT
(Green)
Y
Y
(Blue)
PB
/CB
PB
/CB
L
(Red)
R
(Red)
PR
/CR
PR
/CR
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
Y
RF coaxial
cable
ANT. IN
This connection is for
TV loop through only
VHF / UHF
antenna
IN --- AUDIO --- OUT
L
L
R
R
IN
ANTENNA
L
OUT
PB
/CB
IN
COAXIAL
IN --- VIDEO --- OUT
OUT
PR
/CR
R
Recording
rear of this unit
HDMI OUT
Basic Setup
(Blue)
IN
RF coaxial
cable
or
Playback
ANTENNA
cable TV
company
Connecting to a TV Using the S-Video Out Jack
RCA audio cable
S-VIDEO
Editing
AUDIO
OUT
AUDIO IN
L
Function Setup
L
R
OUT
S-VIDEO IN
S-video cable
R
ANT. IN
VHF / UHF
antenna
OUT
HDMI OUT
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
IN --- AUDIO --- OUT
L
Y
L
IN
ANTENNA
L
OUT
PB
/CB
COAXIAL
IN
R
R
IN --- VIDEO --- OUT
R
PR
/CR
IN
ANTENNA
RF coaxial
cable
or
cable TV
company
Others
Supplied cables used in this connection are as follows:
• RF coaxial cable x 1
• RCA audio cable (L/R) x 1
Please purchase the rest of the necessary cables at your local store.
VCR Functions
RF coaxial
cable
rear of this unit
This connection is for
TV loop through only
Español
EN
17
CONNECTION
Connecting to a TV Using Audio / Video Jacks
IN --- AUDIO --- OUT
L
AUDIO IN
L
RCA audio cable
R
R
IN ---VIDEO --- OUT
VIDEO IN
RCA video cable
rear of this unit
HDMI OUT
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
IN --- AUDIO --- OUT
L
Y
L
IN
ANTENNA
L
OUT
PB
/CB
COAXIAL
IN
R
ANT. IN
R
IN --- VIDEO --- OUT
R
PR
/CR
This connection is for
TV loop through only
RF coaxial
cable
VHF / UHF
antenna
OUT
IN
ANTENNA
RF coaxial cable
or
cable TV
company
Supplied cables used in this connection are as follows:
• RF coaxial cable x 1
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
18
EN
Introduction
CONNECTION
Connecting to a Cable / Satellite Box
RCA video cable
RCA audio cable
L
AUDIO IN
RCA audio
cable
R
L
L
AUDIO OUT
VIDEO OUT
Basic Setup
R
IN ---VIDEO --- OUT
Connections
IN --- AUDIO --- OUT
R
VIDEO IN
RCA video cable
cable/satellite box
RF coaxial
cable
rear of this unit
satellite
dish
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
Y
IN --- AUDIO --- OUT
L
L
R
R
IN
ANTENNA
L
OUT
PB
/CB
COAXIAL
IN
This connection is for
TV loop through only
Recording
ANT.OUT ANT. IN
ANT. IN
HDMI OUT
RF coaxial cable
IN --- VIDEO --- OUT
R
PR
/CR
OUT
IN
or
Playback
RF coaxial
cable
cable TV
company
ANTENNA
Editing
Supplied cables used in this connection are as follows:
• RF coaxial cable x 1
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
Function Setup
Note
VCR Functions
• Required cables and connecting methods differ depending on the cable/satellite box.
For more information, please contact your cable/satellite provider.
• Instead of using VIDEO OUT jack of this unit, you can also use S-VIDEO OUT jack, COMPONENT VIDEO OUT jack or
HDMI OUT jack for connecting to your TV.
With this setup:
• You can record any unscrambled channel by selecting the channel on the cable/satellite box. Be sure that the
cable/satellite box is turned on.
• You cannot record one channel while watching another channel.
Others
Español
EN
19
CONNECTION
Connecting to a TV without Audio / Video Jacks
Set channel 3 or 4
ANT. IN
rear of this unit
HDMI OUT
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
IN --- AUDIO --- OUT
L
Y
L
IN
ANTENNA
L
OUT
PB
/CB
R
IN
COAXIAL
R
IN --- VIDEO --- OUT
R
PR
/CR
VHF / UHF
antenna
IN --- AUDIO --- OUT
OUT
L
R
RF coaxial cable
IN
IN ---VIDEO --- OUT
ANTENNA
RF coaxial
cable
RCA audio cable
RCA video cable
RF coaxial cable
R
TO TV
L
AUDIO IN
VIDEO IN
3
4
CHANNEL
ANT. IN
RF modulator
Set channel 3 or 4
Supplied cables used in this connection are as follows:
• RF coaxial cable x 1
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
Note
• RF modulator is not supplied with this unit. You need to purchase it at your local store.
• The quality of picture may become poor if this unit is connected to an RF modulator.
20
EN
or
cable TV
company
Introduction
CONNECTION
Digital Audio Connection
Coaxial Cable Connection
Connections
DIGITAL
AUDIO OUT
Dolby Digital decoder
rear of this unit
HDMI OUT
OUT
DIGITAL
AUDIO OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
AUDIO
OUT
S-VIDEO
Y
COAXIAL
IN --- AUDIO --- OUT
L
L
R
R
IN
ANTENNA
digital audio
coaxial cable
L
COAXIAL
OUT
PB
/CB
IN
COAXIAL
IN --- VIDEO --- OUT
PR
/CR
R
Basic Setup
digital audio
coaxial input jack
HDMI Audio Connection
AV receiver / amplifier with an HDMI input jack
rear of this unit
HDMI OUT
HDMI IN
HDMI
cable
OUT
DIGITAL
AUDIO OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
AUDIO
OUT
S-VIDEO
HDMI OUT
IN --- AUDIO --- OUT
L
Y
L
IN
ANTENNA
OUT
PB
/CB
IN
R
R
Recording
L
COAXIAL
IN --- VIDEO --- OUT
R
PR
/CR
To set up “HDMI Audio” refer to pages 84 and 92.
To set up “Dolby Digital” refer to pages 82 and 87.
Audio format (disc)
HDMI
Digital Output
PCM
2channel PCM
2channel PCM
Stream
Dolby Digital
Dolby Digital
Dolby Digital
PCM
LPCM
Playback
Dolby Digital Setting of this unit
2channel PCM
Stream
Editing
Actual Output
Cables not included.
Please purchase the necessary cables at your local store.
Function Setup
Note
• The audio source on a disc in a Dolby Digital multi channel surround format cannot be recorded as digital sound
by an MD or DAT deck.
• By connecting this unit to a Dolby Digital decoder, you can enjoy high-quality Dolby Digital multi channel
surround sound as movie theaters.
• Playing back a DVD using incorrect settings may generate noise distortion and may also damage the speakers.
VCR Functions
2 Channel Analog Audio Connection
RCA audio cable
stereo system
IN --- AUDIO --- OUT
AUDIO
OUT
or
AUDIO OUT
L
Others
rear of this unit
R
L
HDMI OUT
OUT
R
L
AUDIO IN
analog audio
input jacks
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
Y
R
IN ---VIDEO --- OUT
IN --- AUDIO --- OUT
L
L
R
R
IN
ANTENNA
L
OUT
PB
/CB
COAXIAL
IN
IN --- VIDEO --- OUT
R
PR
/CR
Español
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
EN
21
BEFORE YOU START
After you have completed all the connections, you must find the viewing channel (external input channel) on your TV.
Finding the Viewing Channel on Your TV
1
2
3
After you have made all the
necessary connections, press
[STANDBY-ON y] to turn on the unit.
Turn on your TV.
• If connected to your VCR make sure it is
switched off or in standby mode before
proceeding.
Press “2” on the TV’s remote control,
then press channel down button
repeatedly until you see “Initial
Setup” menu.
Initial Setup
OSD Language
English
Français
Español
Select the language for Setup display.
This is the correct viewing channel (external
input channel) for the recorder.
• For some TVs, there may be a button on the
TV’s remote control that accesses the external
input channel. It may be labeled “SOURCE”,
“AV”, or “SELECT”. In such case, press it
repeatedly. Refer to your TV’s user manual for
details.
• If more than 10 minutes have passed since you
have turned on the unit, you may see the
MAGNAVOX screen saver instead of “Initial
Setup” menu.
MAGNAVOX screen saver:
Input Mode Names for Common TV Brands (Example)
Admiral AUX
Panasonic TV/VIDEO
Curtis
LINE1, LINE2,
RCA
INPUT, TV/VCR,
Mathis
00, 90, 91, 92, 93
00, 90, 91, 92, 93
GE
INPUT, TV/VCR, Samsung TV/VIDEO
00, 90, 91, 92, 93
Hitachi
INPUT, AUX
Sanyo
VIDEO
00
JVC
VIDEO, VIDEO 1, Sharp
VIDEO 2, VIDEO 3
Kenwood AUX
Sony
VIDEO1, VIDEO2,
VIDEO3
LXI-Series 00
Toshiba
TV/GAME
Magnavox AUX CHANNEL
Zenith
00
Note
• Video input selection varies for different brand’s
models of TVs.
• Consult your TV manufacturer if none of the above is
successful.
22
EN
4
Proceed to step 2 in “INITIAL
SETTING” on page 27.
This unit uses the following on-screen displays and menus to guide you to the easy operations.
The on-screen displays give you the information on the loaded disc or the disc/file in playback, or the HDMI status, etc.
The menus allow you to change the various kinds of settings for playing back, recording, or editing to suit your preference.
Introduction
BEFORE YOU START
Guide to On-Screen Display / Menu
Disc Information / Menu
6
DVD mode
OFF
Connections
The on-screen display changes in the following order
as you press [DISPLAY].
1/ 5
1/ 5
0:01:00 / 1:23:45
DTV Program Guide (only in DTV mode)
-RW
Disc Information/Menu (only in DVD mode)
or
VCR Information (only in VCR mode)
5
1
SP(2Hr)
HDMI Information
(only for the images output through the HDMI output)
1h53m
3
* This is an example screen only for explanation.
Displayed items vary depending on the disc you
inserted.
1. Indicates a disc type.
2. Indicates a channel number or selected external input
channel.
3. Indicates a recording mode and possible recording
time left.
Playback
MP3 Tag Information
(only when an MP3 file is in playback)
4
2
Recording
Title Name Information (only in DVD mode)
(only when DVD+RW/DVD+R/DVD-RW/DVD-R
is in playback)
or
File Name Information (only in CD mode)
(only when a CD with MP3 / JPEG / Kodak picture CD files
is in playback)
Basic Setup
CH 10
4. Indicates an operation status.
5. Each icon means:
: Search
PROGRAM TITLE NAME
69.1
WLIW-DT
90
INFORMATION-1
INFORMATION-2
INFORMATION-3
INFORMATION-4
INFORMATION-5
INFORMATION-6
TV-PG
ENGLISH
: Audio
5
6
7
8
: Subtitle
: Angle
: Repeat
Function Setup
1
2
3
4
Editing
DTV Program Guide
: Marker
: Noise Reduction
: Zoom
: Surround
6. Indicates the current title number/total number of
titles, the current chapter number/total number of
chapters, and time lapse of the current title playback/
total duration of the title.
VCR Functions
Others
1. Program title (max. 2 lines displayed)
2. Closed Caption (Indicates that the program being
broadcast is available with closed captioning.)
3. Signal strength (Indicates the signal strength of the
current channel.)
4. Program guide (max. 6 lines displayed)
5. Channel number
6. Broadcast station
7. Audio language (“Other” is displayed when the
audio language cannot be acquired, or the acquired
languages are other than English, Spanish or French.)
8. Program rating
Note
Español
• When the program guide is displayed in more than 7
lines, use [K / L] to scroll.
• “No description provided.” is displayed when the
program guide is not provided.
EN
23
BEFORE YOU START
VCR Information
VCR mode
MP3 Tag Information
1
• First, track name will be displayed.
12:00AM
CH 21
Stereo
2
3
Track Name
• If you press [DISPLAY] one more time, artist name will
be displayed.
Artist Name
SP
0:00:00
HIFI
4
5
6
* This is an example screen only for explanation.
Displayed items vary depending on the cassette tape
you inserted.
* During stop mode or pause, VCR information is not
available with HDMI connection.
• If you press [DISPLAY] one more time, album name
will be displayed.
Album Name
• If there is no artist, track or album name, “Not Available”
will be displayed.
1. Indicates current video status.
2. Indicates the current time.
3. Indicates a current channel number (or selected
external input channel) and an audio status of the
program.
4. Indicates a recording or playing back mode.
5. Indicates a tape counter.
6. Audio status of the current cassette tape.
HDMI Information
1
Video Info. :
Audio Info. :
480p
/
Bitstream
2
YCbCr
3
Title/File Name Information
Title Name Information
Title Name
4
My Title
File Name Information
File Name
My File
24
EN
*1. Indicates the resolution of the HDMI output image.
*2. Indicates the HDMI video format.
*3. Indicates the HDMI audio format.
4. Indicates current disc status.
* “- - -” will be displayed, when it does not have any
information.
Main Menu
Setup
1
2
3
4
5
General Setting
Timer Programming
Title List
Disc Edit
DISC Playback Mode
General Setting Menu
Playback
Display
Video
Recording
Clock
Channel
HDMI
Reset All
Parental Lock
Disc Audio
Disc Menu Language
Audio Language
Subtitle Language
Angle Icon
Still Mode
<Disc Edit menu (DVD+RW)>
Disc Edit
Edit Disc Name
Erase Disc
Make Edits Compatible
Disc Protect OFF ON
<Disc Edit menu (DVD-RW)>
Disc Edit
Edit Disc Name
Erase Disc
Finalize
Disc Protect OFF
ON
<Disc Edit menu (DVD+R/DVD-R)>
Disc Edit
1
3
2
4
3
Edit Disc Name
Finalize
Disc Protect OFF
ON
<DISC Playback Mode menu (audio CD/VCD)>
DISC Playback Mode
Random Play
Program Play
PBC (Video CD only)
<DISC Playback Mode menu (MP3/JPEG)>
DISC Playback Mode
Music
Photo
Random Play
Slide Show
EN
25
Español
8
1
9
1
5
2
10
2
Others
5
1
6
2
7
3
4
VCR Functions
1
2
3
4
Function Setup
1
2
3
4
1. Edit Disc Name:
Allows you to rename the disc.
2. Erase Disc: (DVD+RW/DVD-RW only)
Allows you to erase all contents in the disc and format
it.
3. Make Edits Compatible: (DVD+RW only)
Allows you to memorize the editing status on the
disc if you have added or deleted chapters, or made
chapters hidden on this unit, and to effect it when
playing back on the other unit.
Finalize: (DVD+R/DVD-RW/-R only)
Allows you to finalize a disc containing recorded titles.
4. Disc Protect :
Allows you to protect a disc from accidental editing or
recording.
5. Random Play:
Allows you to activate the random playback feature.
6. Program Play: (audio CD/video CD only)
Allows you to activate the program playback feature.
7. PBC (Video CD only):
Allows you to select images or information on the
menu screen by activating PBC (playback control)
function.
8. Music :
Allows you to make setting for MP3 playback.
9. Photo :
Allows you to make setting for JPEG playback.
10. Slide Show: (JPEG / Kodak Picture CD files only)
Allows you to select the display time of the slide show
mode.
Editing
Disc Edit / DISC Playback Mode
Playback
1. Playback:
To set up the unit to play back discs as you prefer.
2. Display:
To set up the OSD screen as you prefer.
3. Video:
To set up the video setting.
4. Recording:
To set up the unit to record to discs as you prefer.
5. Clock:
To set up the clock of the unit as you need.
6. Channel:
To adjust the channel setting of the unit as you prefer.
7. HDMI:
To set up the HDMI connection setting.
8. Reset All:
To reset the setting to the factory default.
General Setting
Recording
1
2
3
4
5
6
2
7
3
8
Basic Setup
1. General Setting:
To go to general setting menu.
2. Timer Programming:
To program a timer recording.
3. Title List:
To call up the title list.
4. Disc Edit:
To set up the DVD setting.
5. DISC Playback Mode:
To set up the disc playback setting.
• “DISC Playback Mode” is available only when an audio
CD, a video CD, a CD-RW/-R with MP3 / JPEG / Kodak
picture CD files is inserted into the unit.
Connections
Press [SETUP] to display the main menu. Then use
[K / L] to select a menu and press [OK] to display the
menu. These menus provide entries to all main functions
of the unit.
Introduction
BEFORE YOU START
BEFORE YOU START
Switching DVD / VCR Mode
Because this product is a combination of a VCR and a DVD recorder, you must select first which component you wish
to operate.
DVD mode
VCR mode
Press [SOURCE] on the front panel, or press [DVD] on the
remote control.
(Verify that the DVD indicator is lit.)
Press [SOURCE] on the front panel, or press [VCR] on the
remote control.
(Verify that the VCR indicator is lit.)
VCR button
DVD button
DVD indicator
SOURCE button
VCR indicator
Note
• You cannot switch the mode while in the timer-standby mode.
• Playback will stop when you change the output mode.
How to Insert a Disc / Cassette Tape
How to Insert a Disc
How to Insert a Cassette Tape
1) Press [DVD].
2) Press [OPEN/CLOSE A] to open the disc tray.
3) Place the disc on the disc tray with its label side
facing up.
Align the disc to
the disc tray guide.
4) Press [OPEN/CLOSE A] to close the disc tray.
It may take a while to load
the disc.
1) Press [VCR].
2) Insert a cassette tape as illustrated below.
4 HEAD HI-FI STEREO
Cassette compartment
• Insert from the flap side first with the window side
facing up.
To eject the cassette tape:
Press [C A STOP/EJECT] on the front panel or press
[OPEN/CLOSE A] on the remote control.
To eject the disc:
Press [OPEN/CLOSE A] to open the disc tray, then remove
the disc before turning the unit to the standby mode.
Note
• If you turn this unit to the standby mode, [OPEN/CLOSE A] on the remote control is not available.
Be sure to use [A OPEN/CLOSE] or [C A STOP/EJECT] on the unit.
26
EN
You need to follow these steps when you turn on this unit for the first time.
Use [K / L] to select your desired
language, then press [OK].
Connections
1
2
Follow the procedure in “Finding the
Viewing Channel on Your TV” on
page 22 to display “Initial Setup”
menu.
Introduction
INITIAL SETTING
Initial Setup
Basic Setup
OSD Language
English
Français
Español
Select the language for Setup display.
Initial Setup
Recording
3
Use [K / L] to select the type of
broadcasting signal, then press [OK].
Channel Preset
Playback
Make sure the antenna is
connected to “ANTENNA IN” jack.
Antenna
Cable (Analog)
Cable (Analog / Digital)
Auto Preset will scan all terrestrial channels.
This may take a while to complete.
Auto Presetting Now
EN
27
Español
If a PBS (public broadcasting station) is not
available in your area, press [OK]. Then proceed
to step 5 in “Manual Clock Setting” on page 32.
Others
4
If a PBS (public broadcasting station) is available
in your area, clock setting will automatically be
performed and the correct clock will be displayed
following the channel preset procedure.
Initial setting is then complete.
Press [RETURN] to exit.
VCR Functions
1
Function Setup
CH
Editing
The unit will start getting channels available in
your area.
Antenna:
(When using antenna)
The channels broadcasted in analog TV and digital TV
are automatically scanned and memorized. Only the
receivable channels in the area will be memorized.
Cable (Analog):
(When using basic cable)
The channels broadcasted in analog CATV are
automatically scanned and memorized.
Cable (Analog / Digital):
(When using basic cable)
The channels broadcasted in analog CATV and digital
CATV are automatically scanned and memorized.
CHANNEL SETTING
If you have changed antenna connection, we recommend
that you program available channels in your area with the following procedures.
Auto Channel Scan
1
2
3
4
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
“General Setting” menu will appear.
Use [K / L] to select “Channel”, then
press [OK].
“Channel” menu will appear.
Use [K / L] to select “Auto Channel
Preset”, then press [OK].
Use [K / L] to select the type of
broadcasting signal, then press [OK].
Auto Channel Preset
Antenna
Cable (Analog)
Cable (Analog / Digital)
The unit will start getting channels available in
your area.
• When aerial antenna is connected, select
“Antenna”.
• When connected to CATV, select “Cable
(Analog)” or “Cable (Analog / Digital)”.
To cancel the auto channel preset during
scanning:
Press [RETURN] to go the previous screen or
[SETUP] to cancel.
5
When scanning is over, press [SETUP]
to exit.
To cycle through only the memorized channels, use
[CHANNEL / ].
To select a channel directly (including the ones not
memorized), use [the Number buttons] and [ • ] (for
digital TV channels).
Note
• If the auto channel preset is cancelled during
presetting, some channels not yet preset may not be
received.
• You cannot change the channel when either VCR or
DVD is in any recording mode (basic recording, onetouch timer recording or timer recording).
28
EN
Introduction
CHANNEL SETTING
Adding / Deleting Channels
“General Setting” menu will appear.
Use [K / L] to select “Channel”, then
press [OK].
7
5
Use [K / L] to select “Manual Channel
Preset”, then press [OK].
Use [K / L] to select “Delete”, then
press [OK]. Then select the next
channel to delete.
• If the setting is complete, press [RETURN] to
activate “Manual Channel Preset”.
DTV 2 (CH - - - )
Add
Delete
VCR Functions
Your setting will be activated.
WARNING:
• For the digital TV channels, you cannot recover the
deleted channels once they are deleted unless you
perform the auto channel preset again.
7
Others
• Use [CHANNEL / ] to cycle through only
the memorized channels.
• Use [{ / B] to cycle through all the channels
including the ones not memorized.
• Use [the Number buttons] to select a channel
directly.
• When a memorized channel is selected, “Add”
is checked and highlighted as a default.
• When an unmemorized channel is selected
“Delete” is checked and highlighted as a
default.
6
• Only the major channel is displayed in “Manual
Channel Preset” menu. (The channel number
displayed in the parenthesis is a virtual channel
number)
• Use [CHANNEL / ] to cycle through only
the memorized channels.
• You cannot use [{ / B] for the digital TV
channel selection.
• Use [the Number buttons] to select a channel
directly.
• When a memorized channel is selected, “Add”
is checked and highlighted as a default.
• When an unmemorized channel is selected
“Delete” is checked and highlighted as a
default.
Function Setup
ANALOG
Select the channel number to add or
delete.
DIGITAL
Select the channel number to delete.
Editing
Auto Channel Preset
Manual Channel Preset
TV Audio Select
Press [SETUP] to exit.
Playback
5
Your setting will be activated and it will
automatically switch to the next channel so that
you can continue adding or deleting channels.
“Channel” menu will appear.
• If you are adding or deleting Analog Cable TV
channels, go to 5
to continue.
ANALOG
• If you are deleting Digital TV channels, go to 5
to continue.
DIGITAL
2
Add
Delete
Recording
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
CH
Basic Setup
1
2
3
4
Press [DTV/TV] to select the mode
(DTV or TV) to/from which you want
to add/delete channels.
6
Use [K / L] to select “Add” or
“Delete”, then press [OK].
Connections
You may want to add or delete TV channels if your
channel lineup changes or if you no longer watch some
channels.
Adding channel is only available for the analog TV
channels.
Make sure
• You perform “Auto Channel Scan” before adding or
deleting the channels.
Press [SETUP] to exit.
Español
EN
29
SETTING THE CLOCK
Auto Clock Setting
This unit can set the time and date automatically by
referring to a channel that carries clock information. If a
PBS (public broadcasting station) channel is available on
Cable in your area, follow “Auto Clock Setting” below. If
not, follow “Manual Clock Setting” on page 32.
Make sure
• The cable TV connections are correct.
• Channels are set. (Refer to page 28.)
ANALOG AUTO CLOCK SETTING (Cable TV only)
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
1
2
3
4
“General Setting” menu will appear.
Use [K / L] to select “Clock”, then
press [OK].
“Clock” menu will appear.
Use [K / L] to select “Auto Clock
Setting”, then press [OK].
Use [K / L] to select “Auto”, then
press [OK].
Auto Clock Setting
OFF
Auto
Manual
5
6
Press [SETUP] to exit.
Press [STANDBY-ON y] to turn the
unit to the standby mode.
This unit will search for the time only when the
power is in the standby mode. Initially leave it in
standby mode for at least 15 minutes to give this
unit time to set the clock. Once the clock is set, the
unit receives the clock data at 12:00 am & 12:00 pm
when unit is in standby mode. Check the time after
the Auto Clock was set, if it is incorrect time then set
the “Auto Clock Setting“ to “OFF” in step 4 above.
Then try “Manual Clock Setting“ on page 32.
Manual Auto Clock Setting
If the unit chooses an incorrect PBS channel on Cable
TV, set the PBS channel manually by following the steps
below.
Note
• The clock may set itself automatically after you
connect the antenna/cable signal and plug in the
power cord.
• Only the Analog PBS channel Cable TV signal is
effective for auto clock setting.
• For analog auto clock setting, incorrect time may be
obtained depending on the broadcast information. If
this occurs, set the “Auto Clock Setting” to “OFF” at
step 4 above and try “Manual Clock Setting” on page
32.
30
EN
1
2
Select “Manual” at step 4 above, then
press [OK].
Use [the Number buttons] or [K / L]
to enter your Cable TV Analog PBS
channel number, then press [OK].
Set Channel No.
CH
3
1
Press [SETUP] to exit and turn the
unit to the standby mode.
Introduction
SETTING THE CLOCK
Auto Clock Setting (cont’d)
Use [K / L] to select “Clock”, then
press [OK].
“Clock” menu will appear.
Use [K / L] to select “Auto Clock
Setting”, then press [OK].
• The clock may set itself automatically after this unit
receives the antenna/cable signal and plug in the
power cord.
• If the clock is not set correctly, timer recording does
not work properly.
• Analog off the air broadcasts have ended. Analog
auto clock setting will no longer be available except
via Cable TV. Try digital auto clock setting in this
case.
• For digital auto clock setting, incorrect time may be
obtained depending on the broadcast information.
If this occurs, set the “Auto Clock Setting“ to “OFF” at
step 4 and try “Manual Clock Setting“ on page 32.
Time adjustment for each time zone
GMT (Greenwich Mean Time ) - 4 hours
Eastern
GMT (Greenwich Mean Time ) - 5 hours
Central
GMT (Greenwich Mean Time ) - 6 hours
Enable Manual operation to select the DTV
Channel for receiving the Clock Data and
selecting your Time Zone below.
Mountain
GMT (Greenwich Mean Time ) - 7 hours
Pacific
GMT (Greenwich Mean Time ) - 8 hours
Alaska
GMT (Greenwich Mean Time ) - 9 hours
Press [{ ] to highlight “CH”. Press
[K / L] to select “DTV”, then press
[ B] .
Hawaii
GMT (Greenwich Mean Time ) - 10 hours
OFF
Auto
Manual
Playback
Atlantic
Auto Clock Setting
Recording
Use [K / L] to select “Manual”, then
press [OK].
Editing
Set Channel No.
DTV
1
8
Press [SETUP] to exit and turn the
unit to the standby mode.
Function Setup
6
7
Use [the Number buttons] or [K / L]
to enter the desired major channel
number to receive the Clock Data,
then press [OK].
Use [K / L] to select the desired time
zone, then press [OK].
VCR Functions
Time Zone
Atlantic
Eastern
Central
Mountain
Pacific
Alaska
Hawaii
Others
Español
This unit will search for the time only when the
power is in the standby mode. Initially leave it in
standby mode for at least 15 minutes to give this
unit time to set the clock. Once the clock is set, the
unit receives the clock data at 12:00 am & 12:00 pm
when unit is in standby mode. Check the time after
the Auto Clock was set, if it is incorrect time then set
the “Auto Clock Setting“ to “OFF” in step 4 above.
Then try “Manual Clock Setting“ on page 32.
Basic Setup
5
“General Setting” menu will appear.
Note for auto clock setting
Connections
1
2
3
4
DIGITAL AUTO CLOCK SETTING
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
EN
31
SETTING THE CLOCK
Manual Clock Setting
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
1
2
3
4
Daylight Saving Time
When “Daylight Saving Time” is “ON”, the unit clock will
automatically adjust the time in order to fit the daylight
saving time.
“ON (MAR - NOV)” has been selected as the default.
“General Setting” menu will appear.
Use [K / L] to select “Clock”, then
press [OK].
“Clock” menu will appear.
Use [K / L] to select “Clock Setting”,
then press [OK].
Use [K / L] to select calendar or time,
then press [OK].
Clock Setting
JAN / 01 / 2009 ( THU )
12 : 00 AM
Use [{ / B] to select an item to set,
and use [K / L] to select the contents
to suit your preference, then press
[OK] when you finish setting all the
contents.
5
1
2
3
4
32
Press [SETUP] to exit.
5
EN
“Clock” menu will appear.
Use [K / L] to select “Daylight Saving
Time”, then press [OK].
Use [K / L] to select “ON (MAR NOV)”, “ON (APR - OCT)” or “OFF”,
then press [OK].
ON (MAR - NOV): (Current DST setting dates)
Move forward one hour on the second Sunday in
March and move back one hour on the first
Sunday in November.
ON (APR - OCT):
Move forward one hour on the first Sunday in
April and move back one hour on the last
Sunday in October.
Your setting will be activated.
The clock starts counting when you press [OK].
• Your setting will be cancelled if you press [SETUP]
before pressing [OK] at step 5.
• Your clock setting will be lost if either there is a power
failure or this unit has been unplugged for more than
30 seconds when you set the clock manually.
• For setting the day, year, hour, and minute,
[the Number buttons] can also be used.
• You can set the built-in calendar from the year 2008
up to 2058.
Use [K / L] to select “Clock”, then
press [OK].
ON (MAR - NOV)
ON (APR - OCT)
OFF
JAN / 01 / 2009 ( THU )
12 : 00 AM
Note
“General Setting” menu will appear.
Daylight Saving Time
Clock Setting
6
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
Press [SETUP] to exit.
Switching Analog Mode /
Digital Mode
You can easily switch the analog TV (NTSC) and digital TV
(ATSC) with the remote control.
Channel Selection
[CHANNEL / ]
Use [CHANNEL /
NTSC (analog mode) [Air Time] ATSC (digital mode)
18:00
18:30
] to change the channel.
CH4-1 smallest smallest
CH
CH
CH4-1
CH4
CH4-2
CH4-3
CH4-1 smallest
CH
CH4-3
19:00
19:30
CH4-1
20:00
Recording
CH4-2 smallest
CH
major channel minor channel
: change automatically
: change manually by using [CHANNEL
/
Playback
]
Editing
Function Setup
VCR Functions
[the Number buttons]
Press the channel number with [the Number buttons] to
select a channel you want to watch.
<Analog TV Channels>
Enter the channel number with [the Number buttons] to
select a channel you want to watch.
For 1-digit number
e.g.) 2 ch:
[0] + [2], [2] + [•] or
[2] + leave it for 2 seconds.
For 2-digit number
e.g.) 12ch:
[1] + [2]
<Digital TV Channels>
Enter the major and minor channel number with [the
Number buttons] to select a channel you want to watch.
For 1-digit number
e.g.) 2.2 ch:
major channel
[0] + [2] or [2] + [•]
minor channel
[0] + [2], [2] + [•] or
[2] + leave it for 2 seconds.
For 2-digit number
e.g.) 35.16ch:
major channel
[3] + [5]
minor channel
[1] + [6]
• If you enter 1 digit for major channel and leave it for 2
seconds, the number will be taken as the major channel
and lowest minor channel of the major channel will be
displayed.
• If there is no minor channel input, lowest minor channel
of the major channel will be displayed.
Basic Setup
Select channels by using [CHANNEL / ] or [the
Number buttons] found on remote control.
What is the minor channel?
By using high compression technology, digital
broadcasting offers a service that enables multiple signals
to send simultaneously.
Therefore, you can select more than one program per
major channel since digital broadcasting technology
distinguishes between multiple channels broadcast by a
single network.
Connections
Press [DTV/TV] on the remote control.
• The analog mode and digital mode switch alternately.
About digital TV broadcasting:
With its high definition broadcast, digital broadcasting far
surpasses analog broadcasting in both its picture and
sound quality.
Introduction
TUNER SETTINGS
Note
Others
• It may take up to 5 to 7 seconds to switch the digital
TV channels.
• In digital TV broadcasting, 2 or more channels, called
minor channels, are simultaneously broadcast on one
main channel, called major channel.
Español
EN
33
TUNER SETTINGS
This section describes how to switch the TV audio. When you record a TV program, only the audio selected here will be
recorded.
Selecting TV Audio
Digital TV
1
Press [AUDIO] to cycle through
available audio languages.
English 1/2
• When you press [AUDIO], selected language
will be displayed on the TV screen.
• Every time you press [AUDIO], the language
will be switched.
e.g.) English 1/3 ➔ Spanish 2/3 ➔ Other 3/3
• Available languages differ depending on the
broadcast.
• The language information display will
automatically disappear.
• When you record digital TV broadcasting, the
audio language you have selected will be
recorded.
Note
• You cannot change the audio language for the
recording of digital TV broadcasting.
• Pressing [AUDIO] does not control external device
audio.
• When there is only one audio channel on the
broadcast, pressing [AUDIO] does not display
anything.
34
EN
Introduction
TUNER SETTINGS
Selecting TV Audio (cont’d)
Analog TV
Connections
“General Setting” menu will appear.
Use [K / L] to select “Channel”, then
press [OK].
“Channel” menu will appear.
Use [K / L] to select “TV Audio
Select”, then press [OK].
Recording
Use [K / L] to select “Stereo” or
“SAP”, then press [OK].
TV Audio Select
Playback
Stereo
SAP
Stereo:
Outputs main-audio.
SAP (secondary audio program):
Outputs sub-audio.
Press [SETUP] to exit.
Editing
5
Function Setup
Note on recording analog TV audio
Selected
audio
Stereo
Broadcast
audio
Disc
recording
VCR Functions
• When you record an analog TV program available in
second audio or stereo, you have to select either
“Stereo” or “SAP” in “General Setting” menu
beforehand. Refer to the following table to check an
appropriate setting.
Audio
output
STEREO+SAP
STEREO
STEREO
STEREO
STEREO
STEREO
MONO+SAP
MONO
MONO
MONO
MONO
SAP
SAP
STEREO
STEREO
STEREO
MONO+SAP
SAP
SAP
MONO
MONO
MONO
EN
Español
MONO
STEREO+SAP
Others
SAP
Basic Setup
1
2
3
4
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
35
TUNER SETTINGS
DTV Closed Caption
Digital TV
Digital TV has its own closed captions called DTV CC. Use this menu to change the settings for DTV CC.
1
2
3
4
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
“General Setting” menu will appear.
Use [K / L] to select “Display”, then
press [OK].
Use [K / L] to select “DTV CC”, then
press [OK].
OSD Language
Screen Saver
FL Dimmer
DTV CC
CC Style
V-Chip
Use [K / L] to select “Caption Service”,
then press [OK].
DTV CC
Caption Service
Recording
5
Use [K / L] to the desired DTV closed
caption, then press [OK].
Caption Service
OFF
Service1
Service2
Service3
Service4
Service5
Service6
OFF:
Select if you do not want DTV CC. This is the
default.
Service 1 to Service 6:
Select one of these before changing any other
item in the closed caption menu. Choose
“Service 1” under normal circumstances.
6
36
EN
Press [SETUP] to exit.
Introduction
TUNER SETTINGS
Closed Caption Style
Digital TV
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
“General Setting” menu will appear.
Basic Setup
Use [K / L] to select “Display”, then
press [OK].
Use [K / L] to select “CC Style”, then
press [OK].
OSD Language
Screen Saver
FL Dimmer
DTV CC
CC Style
V-Chip
Recording
1
2
3
Connections
Digital TV can also change the style of its closed caption such as font, color or size, etc.
Playback
4
Use [K / L] to select “User Setting”,
then press [OK].
5
Use [K / L] to select “ON”, then press
[OK].
CC Style
Editing
User Setting
Font Size
Font Style
Font Opacity
Font Color
Edge Type
Edge Color
Back Opacity
Back Color
VCR Functions
ON
OFF
Function Setup
User Setting
Others
Español
EN
37
TUNER SETTINGS
6
Use [K / L] to select the item and
switch the setting for each item you
want to set, then press [OK].
Edge type of the displayed caption can be
switched as below.
Edge Type
None
Raised
Depressed
Uniform
L.Shadow
R.Shadow
• When “User Setting” is set to “ON”, you can set
the following items. CC style set by “User
Setting” will be displayed.
• The setting description for each item is shown
below.
<Edge Color>
Edge color of the displayed caption can be
switched as below.
<Font Size>
Font size of the displayed caption can be
switched as below.
Edge Color
Font Size
White
Black
Red
Green
Blue
Yellow
Magenta
Cyan
Large
Middle
Small
<Font Style>
Font style of the displayed caption can be
switched as below.
<Back Opacity>
Background opacity of the displayed caption can
be switched as below.
Font Style
Style1
Style2
Style3
Style4
Style5
Style6
Style7
Style8
Back Opacity
Solid
Transparent
Translucent
Flash
<Font Opacity>
Font opacity of the displayed caption can be
switched as below.
<Back Color>
Background color of the displayed caption can
be switched as below.
Font Opacity
Back Color
Solid
Transparent
Translucent
Flash
White
Black
Red
Green
Blue
Yellow
Magenta
Cyan
<Font Color>
Font color of the displayed caption can be
switched as below.
Font Color
White
Black
Red
Green
Blue
Yellow
Magenta
Cyan
<Edge Type>
38
EN
7
Press [SETUP] to exit.
Introduction
INFORMATION ON DVD RECORDING
Before you make a recording, read the following information.
Recordable Discs
Recording Mode
Logos
You can select a recording mode among 6 options, and
the recording time will depend on the recording mode
you select as follows.
Disc size
Attributes
8cm Disc
12cm Disc
DVD-R
36 min
SPP (2.5Hr)
45 min
LP (3Hr)
54 min
(good)
EP (4Hr)
72 min
SLP (6Hr)
108 min
(poor)
HQ (1Hr)
60 min
(good)
SP (2Hr)
120 min
SPP (2.5Hr)
150 min
LP (3Hr)
180 min
EP (4Hr)
240 min
SLP (6Hr)
360 min
(poor)
• The recording time is only an estimate. The actual
recording time may differ.
• The audio and video quality gets poorer as the recording
time becomes longer.
• Each time [REC MODE] is pressed, recording mode and
its allowed recording time will be displayed.
Note
Function Setup
VCR Functions
Others
• This unit cannot record to CD-RW or CD-R.
• All high definition pictures will be down converted to
the standard definition pictures when they are
recorded on this unit.
• DVD+RW/+R, DVD-RW/-R and CD-RW/-R recorded on
a personal computer or a DVD or CD recorder may
not be played back if the disc is damaged or dirty or
if there is condensation on the player’s lens.
• If you record a disc using a personal computer, even
if it is recorded in a compatible format it may not be
played back because of the settings of the
application software used to create the disc. (Check
with the software publisher for more detailed
information.)
• Since the recording is made by the VBR (variable bit
rate) method, depending on the picture you are
recording, the actual remaining time for recording
may be a little shorter than the remaining time
displayed on the TV screen.
• You cannot record copy-protected program using
this unit. (Copy-protected signal is included in DVDvideo or some satellite broadcasts.)
• You cannot record “copy-once only” program on
DVD.
Editing
Unrecordable Discs
• DVD-RW recorded in the mode other than +VR is not
recordable on this unit unless you erase all contents in
the disc (refer to page 80).
• DVD-R recorded in the mode other than +VR is not
recordable on this unit.
18 min
Playback
• Following discs are recommended for good recording
quality and are proven to be compatible with this unit.
However, depending on the media condition the unit
may not read the disc properly.
Verbatim
DVD+R 8x,
DVD+RW 4x,
DVD-R 8x,
DVD-RW 2x
JVC
DVD-RW 4x
Maxell
DVD+R 4x/8x/16x, DVD-R 8x/16x
SONY
DVD+R 4x/8x/16x, DVD+RW 4x
TDK
DVD+R 4x/8x/16x
Performance of any other discs are not guaranteed.
• You can play back DVD+RW on most DVD players
without finalizing. However, if you have added or
deleted chapters, or made chapters hidden, you
must perform “Make Edits Compatible” before being
able to see those effects on other units. (Refer to
page 81 for more details.) To play back discs other
than DVD+RW on other DVD players, you will need
to finalize.
HQ (1Hr)
SP (2Hr)
Video/sound
quality
Recording
DVD-RW
DVD+R
Recording
time
Basic Setup
DVD+RW
8cm/12cm, single-sided,
single layer disc
Approx. max. recording time
(SLP mode):
360 minutes (4.7GB) (for 12cm)
108 minutes (1.4GB) (for 8cm)
Recording
mode
Connections
This unit can record to DVD+RW, DVD+R, DVD-RW and
DVD-R.
DVD+R/DVD-R can only be recorded to once. DVD+RW/
DVD-RW can be recorded to and erased many times.
DVD-RW/-R will be recorded in the DVD+VR mode
automatically in this unit.
Español
EN
39
BEFORE RECORDING
Make Recording Compatible
Setting for Auto Chapter
You can set a specified time for chapter marks.
Use this feature to make the unfinalized +VR mode discs
recorded on other unit recordable on this unit. When you
make an additional recording on this unit with “Make
Recording Compatible” set to “ON”, the title menu is
automatically converted to our style.
1) Press [SETUP] and use [K / L] to select “General
Setting”, then press [OK].
“General Setting” menu will appear.
2) Use [K / L] to select “Recording”, then press [OK].
“Recording” menu will appear.
1) Press [SETUP] and use [K / L] to select “General
Setting”, then press [OK].
“General Setting” menu will appear.
3) Use [K / L] to select “Auto Chapter”, then press [OK].
2) Use [K / L] to select “Recording”, then press [OK].
“Recording” menu will appear.
4) Use [K / L] to select a desired time option, then
press [OK].
Auto Chapter
3) Use [K / L] to select “Make Recording Compatible”,
then press [OK].
OFF
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
4) Use [K / L] to select “ON” or “OFF”, then press [OK].
Make Recording Compatible
ON
OFF
ON:
OFF:
Title list will be replaced when you make
additional recordings to the discs recorded by
other units.
Prohibiting additional record to the disc that
has a title list created by other units.
5) Press [SETUP] to exit.
Note
• The interval for auto chapter may be up to two
minutes different from the time option you set.
• A blank chapter may be created depending on the
remaining time of the disc.
5) Press [SETUP] to exit.
Recording the DTV Closed Caption
You can record the DTV Closed Caption as the part of the
image for the recording program and see the recorded
closed caption even with the TV that is not closed caption
compliant.
1) Press [SETUP] and use [K / L] to select “General
Setting”, then press [OK].
2) Use [K / L] to select “Display”, then press [OK].
3) Use [K / L] to select “DTV CC”, then press [OK].
4) Use [K / L] to select “Recording”, then press [OK].
• If “Caption Service” is set to “OFF”, you cannot select
“Recording”.
5) Use [K / L] to select “ON”, then press [OK].
Recording
ON
OFF
6) Press [SETUP] to exit.
Note
• If “Caption Service” is set to “OFF”, the caption will
not be recorded.
40
EN
Follow the steps to record TV programs.
* Make sure the disc is compatible with this unit.
(Refer to page 39 for the list of compatible
discs.)
It may take a while to load
the disc.
Refer to “Recording Mode” on page 39.
Playback
SP(2Hr)
0h58m
Refer to “Switching Analog Mode/Digital Mode”
and “Channel Selection“ on page 33.
Function Setup
Select the appropriate external input
channel by pressing [SOURCE] or
[CHANNEL / ].
Press [DTV/TV] to select analog TV or
digital TV, then use [CHANNEL / ]
or [the Number buttons] and [ • ] (for
digital TV channels) to select a
desired channel to record.
Editing
3
Recording
2
Press [REC MODE] repeatedly to
select a recording mode.
Basic Setup
• When inserting a brand-new DVD+RW/DVD-RW,
the unit automatically starts to format.
• If titles have been recorded on the disc, the
title list is displayed. Press [STOP C] to exit the
title list.
Connections
1
Press [DVD] first.
Insert a recordable disc (refer to page
26 on how to insert a disc).
Introduction
BASIC RECORDING & ONE-TOUCH TIMER RECORDING
CH 12
VCR Functions
Others
Español
EN
41
BASIC RECORDING & ONE-TOUCH TIMER RECORDING
4
Press [REC] to start recording.
“I” will be displayed for 4 seconds.
I
SP(2Hr)
2h00m
Press [PAUSE F] to pause recording.
Press [PAUSE F]] or [REC] again to restart
recording.
5
Press [STOP C] to stop recording.
The recorded title will appear in the title list.
(Refer to “Guide to a Title List” on page 70.)
e.g.) DVD+R
Please finalize the disc when the writing is
completed before playing back on other DVD
players.
Writing to Disc
90%
To set one-touch timer recording (OTR)...
This is a simple way to set the recording time in blocks
of 30 minutes.
Press [REC] repeatedly until the desired recording time
(30 minutes to 6 hours) appears on the TV screen.
One-touch timer recording will start.
I
1
SP(2Hr)
NOV/21/09 11:00AM CH12 SP
NOV/21/09 0:20:44
2
EMPTY TITLE
1:41:17 SP(2Hr)
0h30m
• Press [STOP C] to exit the title list.
0h30m
(normal recording)
6h00m
1h00m
5h30m
To change the recording length during the
one-touch timer recording:
Press [REC] repeatedly until the desired length appear.
To cancel the one-touch timer recording within the
specified time:
Press [STOP C].
Note
•
•
•
•
When you press [REC], recording starts immediately and continues until the disc is full or you stop recording.
This unit cannot record images as aspect ratio of 16:9. The 16:9 images will be recorded as 4:3.
When the unit clock has not been set, the space for a date and time of title names will be blank.
When you record a TV program, you have to select the TV channel audio beforehand. Only the selected channel
audio will be recorded. Refer to “Selecting TV Audio” on pages 34-35 for more details.
• This unit cannot record in both stereo and SAP (secondary audio program) at the same time.
• You cannot change the recording mode during the recording pause mode.
• You can change a channel to be recorded during the recording pause mode.
Note for one-touch timer recording
• The remaining recording time will be displayed on the front panel display during one-touch timer recording. Press
[DISPLAY] to see it on the TV screen.
• Unlike the timer recording, you can perform the following operations during one-touch timer recording.
- Turning the power to standby to stop one-touch timer recording.
- Using [REC] or [STOP C] on the remote control.
• You cannot use the pause function during one-touch timer recording.
• When one-touch timer recording is finished and the power is turned to standby, the unit will switch to the timerstandby mode automatically if a timer recording has been programmed. Press [TIMER SET] to cancel the timerstandby mode to use the unit continuously.
42
EN
Guide to Timer Programming Display
3
1
2
Timer Programming
JAN/ 2/09 12:00 AM 69.1 SP
SP (1:00)
THU JAN/01 11:00AM
Date
JAN/02
Start
End
12:00AM 1:00AM
New Program
CH
DTV69. 1
Connections
You can program the unit to record up to 12 programs
within a month in advance. Daily or weekly program
recordings are also available.
Before recording, make sure to
• Set the clock before setting a timer programming.
• Insert a recordable disc with enough recordable space.
Introduction
TIMER RECORDING
6
1/1
5
Use [K / L] to select “New Program”,
then press [OK].
Playback
1
2
Press [TIMER].
Recording
1 Title of a timer program (Contains date, time, channel,
recording mode of the program)
2 Current date and time
3 Recording mode, and length of the recording
4 Timer program list
5 Total number of pages and current page (2 pages
maximum)
6 Recording media (“ ” (DVD) or “ ” (VCR))
Basic Setup
4
Timer Programming
THU JAN/01 11:00AM
Date
CH
Editing
• If there are 6 or more programs, use
[H / G] to change pages.
Note
3
Use [K / L] to enter the date, then
press [B].
Date
JAN/02
CH
DTV69. 1
Start
--:-REC To
DVD
End
--:-Mode
SP
SP
Daily
MON-SAT
MON-FRI
SAT
2h00m
VCR Functions
JAN/01
Function Setup
When pressing [L] at
the current date, the
date will change as
follows.
e.g.) January 1st
Others
FRI
SUN
JAN/31
Español
• If you have not set the clock yet:
Entry screen for the clock setting will appear instead
of the timer programming list at step 1. Continue
with the step 5 in “Manual Clock Setting” on page 32
before setting a timer programming.
• Use [s / B] to move the cursor to the left and the
right in the entry screen for the timer programming.
• If a basic recording or one-touch timer recording is in
progress on one component (e.g., VCR) and the timer
recording set for the other component (e.g., DVD) is
about to begin, the unit automatically switches to the
programmed channel for timer recording 2 minutes
before the programmed starting time, and the
recording in progress (for VCR) will be cancelled
UNLESS their recording channels are the same. If their
recording channels are the same, the timer recording
will start without canceling the recording currently in
progress. In this case, the recording of the same
channel will be made on both DVD and VCR.
• You cannot make a program whose recording time
exceeds 12 hours.
• Cancel the timer-standby mode by pressing
[TIMER SET] before operation for either DVD or VCR.
When finished operating, press [TIMER SET] to
resume the timer-standby mode.
• In the timer-standby mode, you can turn on the
power and use the component (VCR or DVD) which is
not currently timer-programmed.
Start
End
New Program
EN
43
TIMER RECORDING
4
Use [K / L / s / B] or [the Number
buttons] to enter the start and end
time, then press [B].
Date
JAN/02
CH
DTV69. 1
Start
12 : 00AM
REC To
DVD
7
End
--:-Mode
SP
SP
e.g.) external input mode
Date
JAN/02
CH
L1
Start
12 : 00AM
REC To
DVD
End
1 : 00AM
Mode
SP
SP
1h00m
To record from external input (e.g., cable/
satellite box), select L1 or L2.
Use [K / L] or [the Number buttons] to select
the channel number to record, then press [B].
For digital mode, select both major and minor
channels. Refer to “How to select a channel
number for the timer recording” on page 45
for more details.
e.g.) analog mode
Date
JAN/02
CH
10
Start
12 : 00AM
REC To
DVD
End
1 : 00AM
Mode
SP
SP
1h00m
e.g.) digital mode
Date
JAN/02
CH
DTV69. 1
Start
12 : 00AM
REC To
DVD
Start
12 : 00AM
REC To
DVD
End
1 : 00AM
Mode
SP
1h00m
Refer to “Recording Mode” on page 39.
• When recording to DVD, you can check the
remaining recordable space of the disc when
you select the recording mode.
• You cannot make a program which recording
time exceeds 12 hours.
5
Date
JAN/02
CH
DTV69. 1
SP
2h00m
Use [K / L / s / B] to select analog
(“- - -”) / digital (“DTV”) mode or
external input (L1 / L2), then press [B].
Use [K / L] to select a recording mode.
Date
JAN/02
CH
DTV69. 1
Start
12 : 00AM
REC To
DVD
End
1 : 00AM
Mode
SP
SP
1h00m
Auto recording mode select (DVD only)...
When “Auto” is selected as a recording mode, the unit
calculates how much time is available on the disc and
selects the best recording mode available
automatically to complete recording the program.
Date
JAN/02
CH
DTV69. 1
Start
12 : 00AM
REC To
DVD
End
1 : 00AM
Mode
Auto
Auto
1h00m
• “Auto” is only available for one program in the timer
program list.
• The recording may be cut short when the available
recording space of the disc is too limited.
8
Press [OK] when all items are entered.
After displaying an instructive message for 10
seconds, timer program list will appear.
Press TIMER SET to Timer Standby mode.
When Timer set on DVD or VCR,
it is not available in the standby mode.
Press TIMER SET to cancel the Standby mode.
End
1 : 00AM
Mode
SP
SP
Timer Programming
1h00m
JAN/ 2/09 12:00 AM 69.1 SP
SP (1:00)
THU JAN/01 11:00AM
6
Use [K / L] to select the recording
media (“DVD” or “VCR”), then press
[B].
Date
JAN/02
Start
12 : 00AM
REC To
DVD
End
1 : 00AM
Mode
SP
SP
CH
DTV69. 1
Your program setting is now stored.
• To set another program, repeat steps 2 to 8.
• To exit, press [TIMER] or [SETUP].
• When 2 or more programs are overlapped,
“Timer program overlapped” appears, and the
overlapped program will be displayed in blue.
• To correct the timer program refer to
“Checking, canceling, or correcting the timer
programming information” on page 45.
e.g.) recording to DVD
Date
JAN/02
CH
DTV69. 1
Start
End
12:00AM 1:00AM
1h00m
9
Press [TIMER SET] to set a timer
programming.
will appear on the front panel display, while
this unit waits to make the recording.
CS
DR
CD
HDD
DVD
“VCR” will appear on the front panel display if
VCR timer recording have been set.
44
EN
Introduction
TIMER RECORDING
How to select a channel number for the timer recording
Analog CATV
For channel number 1-12 press, press [B] or [ • ] to decide the channels. For other channels (13125), the channel will be decided as soon as you enter the channel number.
Digital TV
For channel number 1-9 press, press [B] or [ • ] to decide the channels. For other channels (10-99),
the channel will be decided as soon as you enter the channel number.
Digital CATV
For channel number 1-13 press, press [B] or [ • ] to decide the channels. For other channels (14135), the channel will be decided as soon as you enter the channel number.
minor channels
For channel number 1-9 press, press [B] or [ • ] to decide the channels. For other channels (10-99),
the channel will be decided as soon as you enter the channel number.
<Hint>
To stop the timer recording in progress
If the timer program did not complete correctly,
the error number appears in the timer
programming list.
Timer Programming
Playback
1) Press [STOP C ] on the remote control.
2) Confirmation message will appear. Select “Yes”,
then press [OK].
• To stop the timer recording immediately, press
[ C STOP] on the unit.
FRI JAN/02 11:00AM
Checking, canceling, or correcting the timer
programming information
E41
Date
JAN/02
Start
End
12:00AM 1:00AM
New Program
1) Press [TIMER SET].
2) Press [TIMER].
3) Check the information.
CH
DTV69. 1
Editing
1/1
Each error number means:
Timer Programming
JAN/ 2/09 12:00 AM 69.1 SP
SP (1:00)
THU JAN/01 11:00AM
Start
End
12:00AM 1:00AM
New Program
CH
DTV69. 1
E42
No disc when
recording
E25-26 Copy prohibited
program
E43
Already 49 titles
recorded
E29
Disc protected
E44
Already 254 chapters
recorded
E30
Disc full
E45
Copy prohibited
program
E35
PCA full *1
E46
E36
Already finalized
video format disc
E40
Some portion has
not been recorded
because of program
overlapping.
Recording did not
start at the start time.
It is impossible to
record additionally
on a disc recorded
by other units
when setting “
Make Recording
Compatible” to “OFF”.
Unrecordable disc
• E23, E27, E28, E31, E32, E33 and E34 are not displayed.
• A program with the error number is grayed in the timer
programming list.
• Timer program with an error number will be cleared
once the entry screen for the program is displayed.
*1 PCA is a disc's space reserved for recording test.
Español
• Press [TIMER] to check the timer recording in progress.
When the timer recording is proceeding, that
program will be highlighted with red. In this case,
you cannot select any other program.
E24
Others
Note
Power failed
VCR Functions
4-A) To delete the timer program:
1 Use [K / L] to select the program you want to
delete, then press [OK].
2 Use [K / L] to select “Delete”, then press [OK].
Confirmation window will appear.
3 Use [K / L] to select “Yes”, then press [OK].
4-B) To correct the timer program:
1 Use [K / L] to select the program you want to
correct, then press [OK].
2 Use [K / L] to select “Program Change”, then
press [OK].
3 Correct the timer program by using
[K / L / { / B], then press [OK].
5) Press [TIMER] to exit.
6) Press [TIMER SET] to return to the timer standby mode.
E1-22 Recording error other E41
E37-39 than below
Function Setup
Date
JAN/02
Recording
• You can decide the 1-digit channel number by pressing 0 first , then enter desired 1-digit channel number.
e.g.) “5”: [0]+[5]
• For selecting the channels with [K / L] you need to press [B] or [ • ] to decide the channel number.
• For selecting the minor channels with [K / L], please make sure the minor channel your are selecting is existed.
[K / L] does not skip the non-existed minor channels.
Basic Setup
For channel number 2-6 press, press [B] or [ • ] to decide the channels. For other channels (7-69),
the channel will be decided as soon as you enter the channel number.
Connections
Analog TV
EN
45
TIMER RECORDING
Hints for Timer Recording
• If there is a power failure or this unit has been unplugged
for more than 30 seconds, the clock setting and all timer
programming will be lost.
• If a disc is not inserted, "DVD" on the front panel display
flashes and timer recording cannot be performed. In
some cases, will appear momentarily around the start
time as the unit attempts to record. Please insert a
recordable disc.
• If a cassette tape with a erase-protection tab is not in the
cassette compartment or there is no cassette tape in the
cassette compartment, “VCR” on the front panel display
flashes and timer recording cannot be performed. Please
insert a recordable cassette tape.
• If a cassette tape ends during the timer recording, the unit
will automatically stop, eject the cassette tape, and turn
itself to the standby mode. To continue recording, insert a
recordable tape.
• When all the timer recordings are completed, flashes.
Press [TIMER SET] to release the unit from the timer
standby mode.
• If both DVD and VCR are timer programmed, you cannot
use any functions for either unit during timer standby or
timer recording. If you want to use functions other than
recording under such condition, cancel timer recording
by pressing [TIMER SET] during timer standby or stop
recording by pressing [C STOP] / [C A STOP/EJECT] on
the front panel of the unit during timer recording.
• To cancel the timer standby mode, press [TIMER SET].
• When the starting and the ending time are the same,
“Exceeds 12 hours” appears and the program setting will
not be accepted.
• When the disc or cassette tape becomes full during the
recording, the unit turns itself to the standby mode.
• If the starting time is earlier and the ending time is later
than the current time, the recording will start right after
you press [TIMER SET] at step 9 on page 44.
• You cannot change the audio language for the timer
recording of digital TV broadcasting.
• The timer recording cannot be performed in DVD and
VCR at the same time. If you set 2 programs with the same
channel and time in both devices, the program which is
set first will have the priority.
• “Press TIMER SET for timer recording” will appear on the
TV screen 5 minutes before the programmed starting
time.
The Priority of Overlapped Settings
• Timer program which has the earlier start time will be placed first in the timer program list, and be given priority over
the programs with the later start time when timer programs overlap.
• When timer programs overlap, the first 2 minutes (at the longest) of the later recording will be cut off.
• When 2 or more timer programs have the same start time, the program set first will be given priority.
• A timer recording of lower priority will be cancelled or start from the middle.
• Check the overlapped timer programmings and change the priority if necessary.
When the starting time is the same:
A program set previously (PROG. A) has priority.
PROG. A
PROG. B
actual
PROG.
PROG.AA
PROG. B
recording
The first 2 minutes (at the longest) will be cut off
(when recording to DVD only).
Note for DVD recording
• When the recording time of 2 programs are overlapped, or
the end time of a program and the start time of another
program is the same, the first 2 minutes (at the longest) of
the subsequent program will be cut off.
• If the cut-off portion comes up to 3 minutes or more, this
program will be displayed with error number E40 in the
timer programming list.
When the end time of the programming
currently being recorded and the start time
of the subsequent program are same:
The beginning of the PROG. B may be cut off.
PROG. A
PROG. B
actual
recording
PROG. A
PROG. B
The first 2 minutes (at the longest) will be cut off.
46
EN
Overwriting from the Beginning of
the Title
2) Load the disc that includes a title to be overwritten.
Title list will appear.
If the title list does not appear, press [TITLE].
3) Press [REC MODE] repeatedly to select a recording mode.
Refer to “Recording Mode” on page 39.
1
SP (2Hr)
NOV/21/09 11:00AM CH12 SP
NOV/21/09 0:20:44
2) Use [K / L] to select “Play”, then press [OK].
Playback will start.
3) Press [PAUSE F] at the point from which you want
to start overwriting.
4) Press [REC].
“S I”, display menu, channel, and the time lapse will
be displayed as illustrated on the left.
5) Select the channel you want to record.
(Refer to page 33 on how to select a channel.)
6) Press [REC] again.
Overwriting recording starts.
2
NOV/22/09 11:35AM CH13 EP
NOV/22/09 0:10:33
3
This operation may take a
while to be completed.
5) Use [K / L] to select “Overwrite”, then press [OK].
1
SP (2Hr)
2
• Recording mode of the overwriting title is the same
as that of the original (overwritten) title when
overwriting in the middle of the title.
• Title name will not be overwritten.
Function Setup
6) Select the channel you want to record.
(Refer to page 33 on how to select a channel.)
e.g.) DVD+RW
Note
Editing
NOV/21/09 11:00AM CH12 SP
NOV/21/09 0:20:44
Playback
7) Press [STOP C] to stop recording.
EMPTY TITLE
1:37:52 SP(2Hr)
Play
Edit
Overwrite
Recording
4) Use [K / L] to select a title to be overwritten, then
press [OK].
You can overwrite the existing title from the selected
position.
1) Follow the steps 1, 2 and 4 on the left.
selected title number
to be overwritten
1
1
0:00:00
+RW
CH 12
SP(2Hr)
VCR Functions
FI
Basic Setup
It takes a while to display
the title list.
Overwriting in the Middle of the Title
Connections
You can overwrite the existing title from the beginning.
1) Press [STANDBY-ON y].
Make sure that the TV input is set on the unit.
Introduction
OVERWRITING UNNECESSARY TITLE
2h00m
7) Press [REC].
Overwriting recording starts.
The elapsed-time counter starts running.
Others
8) Press [STOP C] to stop recording.
Title name is also overwritten.
This operation may take a
while to be completed.
Note
Español
• The remaining recording time is displayed on the
bottom right corner of the TV screen during
overwriting.
EN
47
OVERWRITING UNNECESSARY TITLE
Hints for Overwriting
When you overwrite on the unnecessary title, there were various circumstances such as follows. Please note that
following cases only describe the overwriting without any recording mode discrepancy. To avoid accidental deletion
please check if there is no important title after the overwriting point.
When overwriting title is shorter than the existing title:
(overwriting from the beginning of the title)
overwrite
recording : A
30 - 180 seconds will be cut off.
after
overwriting
existing title : B
title name : A
title name : B
When overwriting title is longer than the existing title:
(overwriting from the beginning of the title)
overwrite
recording : A
after
overwriting
existing title : B
title name : A
overwrite
recording : A
existing title : B
30 - 180 seconds will be cut off.
after
overwriting
title name : A
title name : C
existing title : C
When overwriting in the middle of the title:
overwrite
recording : A
existing title : B
30 - 180 seconds will be cut off.
after
overwriting
title name : B*
title name : B
*Overwritten section and the rest of the sections will
have the same title name as the original existing
title (B).
Note
• When a title name is overwritten, its thumbnail is also overwritten.
• “Auto Chapter” interval time is reset at the overwriting start point.
• A chapter mark is put at the beginning of the overwrite title when overwriting in the middle of the title.
48
EN
Introduction
SETTINGS FOR AN EXTERNAL DEVICE
Connection to an External Device
Connect the external device properly to the unit by using input jacks either L2 (Front) or L1 (Rear).
When connecting an external device of monaural output to this unit, use AUDIO L jack of L2 (Front) or L1 (Rear).
Use S-video or the RCA audio/video cables for this connection.
Connections
or
S-VIDEO
OUT
VIDEO
OUT
AUDIO OUT
R
L
S-VIDEO
OUT
external device
VIDEO
OUT
AUDIO OUT
R
L
(camcorder, VCR etc.)
or
RCA
video
cable
RCA
audio
cable
S-video
cable
S-VIDEO
RCA
video
cable
or
Basic Setup
S-video
cable
RCA
audio cable
IN --- AUDIO --- OUT
or
IN
L
L
R
R
Recording
IN ---VIDEO --- OUT
L2
L1
to L2 IN
to L1 IN
HDMI OUT
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
Y
IN --- AUDIO --- OUT
L
L
R
R
IN
COAXIAL
IN ---VIDEO --- OUT
R
front of this unit
IN
Playback
ANTENNA
B
R
rear of this unit
5
Use [K / L] to select the input jack
type to connect, then press [OK].
If you want to use VIDEO IN jack, select “Video
In”.
If you want to use S-VIDEO IN jack, select
“S-Video In”.
Others
Video In
S-Video In
6
Press [SETUP] to exit.
Español
Submenu will appear.
L1 (Rear)
L2 (Front)
L1 (Rear)
“General Setting” menu will appear.
Use [K / L] to select “Video”, then
press [OK].
Video Input
VCR Functions
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
Use [K / L] to select desired external
input, then press [OK].
Function Setup
1
2
3
4
Use [K / L] to select “Video Input”,
then press [OK].
Editing
Supplied cables used in this connection are as follows:
• RCA audio cable (L/R) x 1
• RCA video cable x 1
Please purchase the rest of the necessary cables at your local store.
EN
49
SETTINGS FOR AN EXTERNAL DEVICE
Recording from an External Device
Before recording from an external device, refer to the
instructions for the connection on page 49.
1
Recording to a DVD
Press [DVD].
Insert a recordable disc (refer to page
26 on how to insert a disc).
It takes a while to load the disc.
Recording to a Cassette Tape
Press [VCR].
Insert the cassette tape with an
erase-protection tab intact.
6 4
2
Select the appropriate external input
channel (L1 or L2) by pressing
[SOURCE] or [CHANNEL / ].
3
4
5
6
Press [REC MODE] repeatedly to
select a recording mode.
• If the external device is connected to the rear
of this unit, select L1.
• If the external device is connected to the front
of this unit, select L2.
• You can also select L1 or L2 channel by using
[the Number buttons].
e.g.) For L1, press [0], [0], [1].
Refer to “Recording Mode” on page 39 for DVD,
or “Recording” on page 94 for VCR.
Press [I RECORD] on the unit to start
recording.
Start playback on the external device
to record from.
For disc:
Press [C STOP] on the unit to stop
recording.
For cassette tape:
Press [C A STOP/EJECT] on the unit
to stop recording.
This operation may take a
while to be completed.
6 4
50
EN
You can copy contents in a DVD to a cassette tape, or do
vice versa. This function is available only when the contents
are not copy-protected. (Before you start, refer to page 39
for the list of compatible discs.)
Introduction
BI-DIRECTIONAL DUBBING
Basic Setup
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
“General Setting” menu will appear.
Use [K / L] to select “Recording”,
then press [OK].
Recording
“Recording” menu will appear.
Use [K / L] to select “Dubbing
Mode”, then press [OK].
Selection menu will appear.
Playback
1
2
3
Connections
Preparing for dubbing (cassette tape to DVD):
• Insert a cassette tape to be dubbed.
• Insert a recordable DVD.
• Make sure there is enough space on the DVD.
Preparing for dubbing (DVD to cassette tape):
• Insert a disc to be dubbed.
• Insert a cassette tape with an erase-protection tab in
tact.
• Make sure there is enough recordable length on the
tape.
Editing
Function Setup
VCR Functions
Note for dubbing
Others
• Dubbing direction setting in “Dubbing Mode” menu
is always reset to “VCR DVD” whenever you turn
the power to the standby mode.
• You cannot change the output mode during VCR to
DVD or DVD to VCR duplication.
Note for recording to a tape:
Make sure
- the cassette tape’s erase-protection tab is intact.
- the cassette tape is long enough.
Note for recording to a disc:
Make sure
- the disc is compatible (refer to page 39).
Español
EN
51
BI-DIRECTIONAL DUBBING
VCR to DVD
4
5
6
7
8
9
Use [K / L] to select “VCR
then press [OK].
DVD to VCR
DVD”,
Dubbing Mode
VCR
DVD
DVD
VCR
4
Use [K / L] to select “DVD
then press [OK].
VCR”,
Dubbing Mode
VCR
DVD
DVD
VCR
Press [SETUP] to exit.
Press [SETUP] to exit.
Press [VCR], then press [PLAY B] to
find the point where you wish to start
dubbing.
Press [DVD], then press [PLAY B] to
find the point where you wish to start
dubbing.
Press [PAUSE F] when you come to
the desired start point.
Press [DVD], then press [REC MODE]
repeatedly to select the desired
recording mode.
Press [D.DUBBING].
VCR to DVD duplication will start.
Press [STOP C] to stop the dubbing.
5
6
7
8
9
Press [PAUSE F] when you come to
the desired start point.
Press [VCR], then press [REC MODE]
repeatedly to select the desired
recording mode.
Rewind or fast forward the tape to the point
where you want to start recording.
Press [D.DUBBING].
DVD to VCR duplication will start.
Press [STOP C] to stop the dubbing.
Note for DVD to VCR duplication
• This function is available for audio CD, but not with MP3 / JPEG / Kodak Picture CD files.
• The recording mode for VCR cannot be displayed at step 7 when using HDMI / Component / S-Video connection.
To display the VCR recording mode on the screen, the unit must be connected by the VIDEO OUT jack and the TV’s
input select should be set to the appropriate external input channel.
Note for VCR to DVD duplication
• After starting VCR to DVD duplication, the picture may be distorted because of the auto tracking function. This is
not a malfunction. Be advised to play back the tape until the picture is stabilized, then set the starting point which
you wish to start recording, and start VCR to DVD duplication.
• This unit will automatically stop the duplication if playback with no image is detected for more than 3 minutes
during VCR to DVD duplication.
• Playback sound mode of the dubbed contents is determined by the playback sound mode of the VCR at the point
of dubbing.
52
EN
To prevent accidental recording, editing or erasing the
titles, you can protect them from “Disc Edit” menu.
Press [SETUP].
Use [K / L] to select “Disc Edit”, then
press [OK].
Basic Setup
Use [K / L] to select “Disc Protect
OFF ON”, then press [OK].
Connections
1
2
3
Introduction
SETTING A DISC TO PROTECT
e.g.) DVD+RW
Disc Edit
Edit Disc Name
Erase Disc
Make Edits Compatible
Disc Protect OFF ON
Recording
Protect this disc?
Yes
No
Playback
4
Use [K / L] to select “Yes”, then press
[OK].
A disc will be protected.
Editing
This operation may take a
while to be completed.
Function Setup
VCR Functions
Note
To cancel the disc protect:
• When you insert a disc protected with this unit,
“Disc Protect ON OFF” will appear instead of “OFF
ON” at step 3.
Disc Edit
Others
Edit Disc Name
Erase Disc
Make Edits Compatible
Disc Protect ON OFF
Español
To release the protection for the disc, select “Disc
Protect ON OFF” at step 3, then follow rest of the
procedures.
EN
53
PLAYING THE DISCS ON OTHER DVD PLAYERS
Finalizing a Disc
You will need to finalize DVD+R, DVD-RW or DVD-R to
play them back on other DVD players.
Finalizing may take several minutes up to an hour.
A shorter recording period on the disc will require a
longer time period for finalization. Do not unplug the
power cord during finalization.
1
2
3
4
Press [SETUP].
Use [K / L] to select “Disc Edit”, then
press [OK].
“Disc Edit” menu will appear.
Use [K / L] to select “Finalize”, then
press [OK].
Use [K / L] to select “Yes”, then press
[OK].
Finalize disc?
Yes
No
Finalizing will start.
Finalizing
90%
To cancel finalizing...
(DVD-RW only)
• To cancel finalizing at step 4, press [STOP C], select
“Yes” with [K / L], then press [OK]. Finalizing is
cancelled and the unit will be in stop mode.
Do you want to cancel ?
Yes
No
Finalizing
Note
• Once you have finalized a DVD+R/ DVD-R, you
cannot edit or record anything on that disc.
• There is no need to finalize DVD+RW.
• When you insert a DVD-RW finalized with this unit,
“Undo Finalize” will appear instead of “Finalize”.
• If
appears when pressing [STOP C], you cannot
cancel finalizing because the finalizing process
cannot be stopped.
• When selecting “No” and press [OK] or [RETURN] ,
finalizing will be continued.
• You cannot cancel finalizing the DVD+R/DVD-R once
it has started.
This operation may take a
while to be completed.
Disc Edit
Edit Disc Name
Erase Disc
Undo Finalize
Disc Protect ON
OFF
To release the finalizing for the disc, select “Undo
Finalize” at step 3.
* DO NOT turn the power off or to the standby mode
during finalization, this will result in a malfunction.
54
EN
5%
5
Finalizing is completed.
Introduction
PLAYING THE DISCS ON OTHER DVD PLAYERS
Auto Finalizing
Use [K / L] to select “Recording”,
then press [OK].
“Recording” menu will appear.
Use [K / L] to select “Auto Finalize”,
then press [OK].
Use [K / L] to select “Disc Full” or
“End of Timer Rec”, then press [OK].
Auto Finalize
Disc Full
End of Timer Rec
e.g.) “Disc Full”
Playback
Use [K / L] to select “ON”, then press
[OK].
Recording
5
“General Setting” menu will appear.
Basic Setup
1
2
3
4
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
Connections
You can finalize discs automatically using this function.
You can use this function to finalize discs after finishing
timer recordings and at the end of the disc space.
Disc Full
ON
OFF
Editing
Your setting will be activated.
Function Setup
6
Press [SETUP] to exit.
VCR Functions
Others
Note
Español
• This function is not available after finishing daily or
weekly program recording.
EN
55
INFORMATION ON PLAYBACK
Before you play back DVD, read the following information.
Playable Discs and Files
Unplayable Discs
This unit is compatible to play back the following discs.
To play back a DVD, make sure that it meets the
requirements for region codes and color systems as
described below. You can play back discs that have the
following logos will play back on the unit. Other disc
types are not guaranteed to play back.
Playable discs
Logos
DVD-video
DVD+RW
The following discs will not play back on this unit.
• CD-ROM
• Compact Disc-Interactive (CD-I)
• DVD-RAM
• Video Single Disc (VSD)
• DVD-ROM
• DVD-audio
• Unfinalized disc
• DVD or CD contains Windows Media™ Audio/DivX® files
• DVD-R or DVD-RW recorded in VR mode or non
compatible recording format
• Blu-ray Disc
• HD DVD
• Super Video CD
On the following disc, the sound may not be heard.
• Super audio CD - Only the sound on the CD layer can be
heard. The sound on the high-density super audio CD
layer cannot be heard.
DVD+R
Color Systems
DVD is recorded in different color systems throughout
the world. The most common color system is NTSC
(which is used primarily in the United States and Canada).
This unit uses NTSC, so DVD you play back must be
recorded in the NTSC system. You cannot play back DVD
recorded in other color systems.
DVD-RW
(Finalized video mode discs only)
DVD-R
(Finalized video mode discs only)
Region Codes
CD-DA (audio CD)
This unit has been designed to play back DVD
with region 1. DVD must be labeled for ALL
regions or for region 1 in order to play back on
the unit. You cannot play back DVD that are
labeled for other regions. Look for the symbols
on the right on your DVD. If these region
symbols do not appear on your DVD, you cannot
play back the DVD in this unit.
The number inside the globe refers to region of the
world.
A DVD labeled for a specific region can only play back on
the unit with the same region code.
video CD
CD-RW
CD-R
Kodak Picture CD
Playable files
Media
MP3
CD-RW/-R
JPEG
is a trademark of DVD Format/Logo Licensing Corporation.
56
EN
PBC (playback control) for Video CD
Note
DVD
title 1
chapter 1 chapter 2
track 1
chapter 1
title 2
chapter 2
audio CD, video CD
track 2
track 3
track 4
chapter 3
track 5
Basic Setup
MP3, JPEG
folder 1
file 1
folder 2
file 2
file 3
file 4
file 5
Recording
• PBC setting turns to “ON” when loading video CD
with PBC function, thus, even after setting PBC to
“OFF” and ejecting the video CD then reloading the
video CD, this setting turns to “ON” automatically.
• Some operations cannot be performed while PBC
function is on. Cancel PBC function temporarily to
perform those operations by following the
instruction below.
Hint for DVD Playback
The contents of DVD are generally divided into titles.
Titles may be further subdivided into chapters.
Connections
You can select images or information on the menu
screen by activating the PBC (playback control) function
of the video CD.
This unit conforms to ver.1.1 and ver. 2.0 of video CD
standard with PBC function.
Ver.1.1 (without PBC function): You can enjoy playback
picture as well as music CD.
Ver.2.0 (with PBC function): While using a video CD with
PBC function, “PBC” appears on the TV screen.
Introduction
INFORMATION ON PLAYBACK
Playback
1) Press [SETUP].
2) Use [K / L] to select “DISC Playback Mode”, then
press [OK].
“DISC Playback Mode” menu will appear.
3) Use [K / L] to select “PBC (Video CD only)”, then
press [OK].
4) Use [K / L] to select “ON” or “OFF”, then press [OK].
Your setting will be activated.
You can play back interactive software using menu
screens. Refer to instructions in the video CD.
Editing
Function Setup
VCR Functions
Others
Español
EN
57
BASIC PLAYBACK
Direct Playback
1
Press [DVD] first.
Insert a playable disc (refer to page
26 on how to insert a disc).
Align the disc to
the disc tray guide.
* Make sure the disc is compatible with this unit.
(Refer to page 56 for the list of compatible discs.)
It may take a while to load
the disc.
2
3
Note
• Some discs may start playback automatically.
• You can select images or information on the menu
screen by activating PBC (playback control) function
(page 57).
• Playback will stop when you change the output mode.
58
EN
Press [PLAY B] to start playback.
If you are playing back a DVD-video or video CD
with PBC function, a menu may appear.
Refer to “Using the Title / Disc Menu” on page
61.
Press [STOP C] once to stop playback
temporarily.
• Refer to “Resume Playback” on page 62.
Playback from the Title List
Connections
If you want to see disc information, press [{ ] when the
first page of the title list is displayed or press [ K ] when
the first title is selected but not when “Play”, “Edit” or
“Overwrite” is highlighted.
e.g.) DVD+RW
Introduction
BASIC PLAYBACK
No Disc Name
DVD+RW
Total Titles
3
Disc Space Used
0:30:48
Disc Protect
OFF
Make Edits Compatible
Needed
Basic Setup
Disc
e.g.) DVD+R
Recording
No Disc Name
Disc
* Make sure the disc is compatible with this unit.
(Refer to page 56 for the list of compatible discs.)
• Title list will appear automatically.
• To exit the title list, press [STOP C].
• To resume the title list, press [TITLE].
1
SP (2Hr)
NOV/21/09 11:00AM CH12 SP
NOV/21/09 0:20:44
3
EMPTY TITLE
1:37:52 SP(2Hr)
Finalized
3
Use [K / L] to select “Play”, then
press [OK].
Play
Edit
Overwrite
1
SP (2Hr)
NOV/21/09 11:00AM CH12 SP
NOV/21/09 0:20:44
2
NOV/22/09 11:35AM CH13 EP
NOV/22/09 0:10:33
Others
3
EMPTY TITLE
1:37:52 SP(2Hr)
Playback will start.
4
Press [STOP C] once to stop playback
temporarily.
• Refer to “Resume Playback” on page 62.
EN
59
Español
• Some discs may start playback automatically.
• You can also start playback by pressing [PLAY B]
instead of [OK] at step 2.
Finalize
1. Disc name
(Default “No Disc Name”)
2. Disc type
(DVD+RW/DVD+R/ DVD-RW/DVD-R)
3. Total number of title
(include “EMPTY TITLE”)
4. Total time of recorded disc space
5. Status of disc protection
(“ON” is protected disc.)
6. Making edits compatible/finalize
• When DVD+RW is inserted:
If the disc needs to be set “Make Edits Compatible”,
“Needed” is displayed. Otherwise, “Not Needed” is
displayed. (Refer to page 81.)
• When DVD+R, DVD-RW or DVD-R is inserted:
If “Finalize” is done, “Finalized” is displayed.
Otherwise, “Unfinalized” is displayed.
• For video CD, when “PBC (Video CD only)” in
“DISC playback Mode” menu is set to “ON”, the
video CD main menu will appear when
inserting a disc. In such case, select a numbered
menu with [the Number buttons].
• Press [B] to display the next page, and press
[{] to display the previous page.
Note
OFF
VCR Functions
2
NOV/22/09 11:35AM CH13 EP
NOV/22/09 0:10:33
Disc Protect
Function Setup
2
Use [K / L] to select a desired title,
then press [OK].
1:30:48
Editing
It may take a while to load
the disc.
5
Disc Space Used
Playback
1
Press [DVD] first.
Insert a playable disc (refer to page
26 on how to insert a disc).
DVD+R
Total Titles
BASIC PLAYBACK
Playing Back an Audio CD and a CD-RW / -R with MP3 / JPEG Files
1
Press [DVD] first.
Insert a playable disc (refer to page
26 on how to insert a disc).
* Make sure the disc is compatible with this unit.
(Refer to page 56 for the list of compatible discs.)
It may take a while to load
the disc.
When an audio CD is inserted, track list will appear.
When a CD-RW/-R with MP3 / JPEG files is inserted,
file list will appear.
When you insert a CD-RW/-R mixed with MP3/JPEG
files, the playback media selection screen will be
displayed.
For MP3, select “Music”, for JPEG, select “Photo”.
• To exit the track/file list, press [STOP C].
• To resume the track/file list, press [TITLE].
2
Use [K / L] to select a desired folder
or track/file, then press [OK].
e.g.) File list
File List
DISC NAME
Folder 1
Folder 2
MP3 file 1
MP3 file 2
MP3 file 3
MP3 file 4
MP3 file 5
MP3 file 6
1/ 2
Note
• The audio source of MP3 files cannot be recorded as
digital sound by an MD or DAT deck.
• Files whose extension is other than “.mp3(MP3)” or
“. jpg / . jpeg (JPEG)” will not be listed.
• Some unplayable folders or files may be listed due to
the recording status.
• High-resolution JPEG files take longer to be displayed.
• Progressive JPEG files (JPEG files saved in progressive
format) cannot be played back on this unit.
60
EN
When selecting track/file:
Playback will start.
When selecting the folder (Not available for audio CD):
The files in the folder will appear.
Use [K / L] to select the file or folder you want to play
back, then press [OK].
• Press [PLAY B], [OK] or [B] to move to any lower
hierarchies.
• Press [s] or [RETURN] to move back to the previous
hierarchy.
Hints for audio CD tracks and MP3 / JPEG files:
• Folders are shown by
.
• Audio CD tracks are shown by
.
• MP3 files are shown by
.
.
• JPEG files are shown by
• The system can recognize up to 255 folders, up to 99
tracks/999 files.
• Letters of a file/folder name overflowing the given space
will be displayed as “...”. Unrecognizable characters will
be replaced with asterisks.
• If there are no files in the folder, “No Files” will be displayed.
It is recommended that files to be played back in this
unit are recorded under the following specifications:
<MP3>
• Sampling frequency
: 44.1 kHz or 48 kHz.
• Constant bit rate
: 112 kbps - 320 kbps
<JPEG>
• Upper limit
: 6,300 x 5,100 dots.
• Lower limit
: 32 x 32 dots.
• File size of image maximum : 12 MB.
Playing Back an Audio CD and a
CD-RW / -R with MP3 / JPEG Files (cont’d)
Kodak Picture CD
DVD or video CD with PBC function may contain a title
list, which describes the contents of the disc, or a disc
menu, which guides you through the available functions
in the disc.
Press [DVD] first.
1) Insert a playable disc (refer to page 26 on how to
insert a disc).
* Make sure the disc is compatible with this unit. (Refer
to page 56 for the list of compatible discs.)
It may take a while to load the disc.
Picture CD
Image 1
1
2
3
4
5
6
2) Press [TITLE] or [DISC MENU] to call up the title list
or disc menu.
Recording
3) Use [K / L / { / B] to make a selection, and then
press [OK] to enable your selection.
1/2
Note
• You can select a numbered menu with [the Number
buttons] also.
• Menus vary among discs. Refer to the information
accompanying the disc for details.
• [TITLE] or [DISC MENU] will not always be active
with all DVD.
• For video CD, when “PBC (Video CD only)” in “DISC
Playback Mode” menu is “ON”, the video CD main
menu will appear when inserting a disc.
3) Press [STOP C] to stop playback.
• Press [TITLE] to display the thumbnail again.
1) During playback, press [PAUSE F].
Playback will be paused and sound will be muted.
VCR Functions
• After track is displayed for 5 seconds or 10 seconds
(set in “Slide Show” on page 65) the display moves to
the next track.
During JPEG or Kodak Picture CD playback, press [B]
or [{] to rotate a picture 90 degrees clockwise or
counterclockwise respectively.
(Not available when the display menu appears.)
Function Setup
Pause
Notes on JPEG and Kodak Picture CD:
Editing
2) Use [K / L / { / B] to select a desired track to be
played back, then press [PLAY B] or [OK].
An image will be played back from the selected track
and go to the next one in turn.
4) Press [STOP C] to exit.
Playback
• To exit the Picture CD thumbnail List, press [RETURN]
or [STOP C].
Arrow icons mean the title list includes a next or
previous page. Use [{ / B] in the direction of the
icon you wish to follow. You can quick review the six
thumbnails at once between the first and last pages
by pressing [H] / [G].
Basic Setup
1) Press [TITLE].
Using the Title / Disc Menu
Connections
The Picture CD is a service to convert photographs taken
by a conventional film camera into digital data and write
the data on a CD. You can enjoy picture images on the TV
set by playing back the Picture CDs.
For details of Kodak Picture CD, contact a shop that
provides developing service of Kodak Inc.
Introduction
BASIC PLAYBACK
F
Others
2) Press [PLAY B] to return to the normal playback.
Note
• On DVD, set “Still Mode” to “Field” in “Playback”
menu if pictures in the pause mode are blurred.
(Refer to page 87.)
Español
EN
61
SPECIAL PLAYBACK
Resume Playback
You can play back from where you stopped playing back
the disc last.
1) During playback, press [STOP C].
The resume message will appear.
Skipping TV Commercials During
Playback
You can skip TV commercials to enjoy the recorded
programs without interrupting.
Resume ON
2) Press [PLAY B].
In a few seconds, playback will resume from the point
at which it stopped last. You can resume playback at
the same point even if you turn the unit to the standby
mode.
To cancel the resume playback and start playing back
the disc from the beginning, press [STOP C] again
while the playback is stopped.
During playback, press [CM SKIP].
Normal playback will start at 30 seconds ahead from the
point you press [CM SKIP].
Every time you press [CM SKIP], the searching point will
be extended by 30 seconds ahead.
You can press [CM SKIP] up to 6 times (180 seconds).
e.g.) Press [CM SKIP] once.
CM Skip 30 sec.
(forwarding 30 seconds)
Note
• For MP3 / JPEG files, playback will resume from the
beginning of the file at which play back was stopped.
• Resume Playback is available when you play back the
video CD without PBC function.
• Some video CD with the PBC function resume
playback from the beginning of the track.
Fast Forward / Fast Reverse Playback
B
Playback will return to the normal playback.
Rapid Playback
1) During playback, press [D] or [E].
Every time you press [D] or [E], approximate speed
will be changed as follows.
Fast forward or fast reverse playback across titles (for
DVD) or files (for MP3 files) is not possible.
Rapid playback function is available only during
playback.
This function is available only on discs recorded in the
Dolby Digital format, and plays back in a slightly faster/
slower speed while keeping the sound quality just as
normal playback.
1) During playback, press [RAPID PLAY].
40x
20x
5x
normal
speed
playback
2x
20x
40x
For video CD, approximate forward/reverse speeds are
2x, 8x, 16x.
For audio CD, MP3 files, approximate speed is fixed at
/
).
8x with sound (indicated with
2) Press [PLAY B] to return to the normal playback.
Bx0.8: Press [RAPID PLAY] once during playback.
Plays back approximately at 0.8 times of normal
playback.
Bx1.3: Press [RAPID PLAY] twice during playback.
Plays back approximately at 1.3 times of normal
playback.
B:
Note
• Forward/reverse speed will be indicated with icons
as follows.
forward (approx. speed)
2x:
20x:
40x:
reverse (approx. speed)
5x:
20x:
40x:
62
EN
Press [RAPID PLAY] 3 times to play back in
normal speed.
No effects.
2) Press [PLAY B] to return to the normal playback.
Note
• Audio (language) setting cannot be changed while
using this mode.
• This feature may not work at some point in a disc.
• Audio is PCM during rapid playback mode except
when using digital audio connection.
• When using digital audio connection (COAXIAL), the
LPCM sound (2 channel) will be output.
Step by Step Playback
Introduction
SPECIAL PLAYBACK
Zoom
1) During playback, press [DISPLAY] to bring up the
display menu.
2) Use [{ / B] to select
menu.
e.g.) DVD-video
1/ 5
to display the selection
1/ 5
Basic Setup
0:01:00 / 1:23:45
DVD Video
3) Use [K / L] to select a desired zoom factor to zoom,
then press [OK].
• Only step by step forward playback is available for
playing back video CD.
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
× 1.2
× 1.5
× 2.0
Slow Forward / Slow Reverse Playback
Playback
1) During playback, press [PAUSE F]. Then press
[D] or [E].
Every time you press [D] or [E], approximate speed
will be changed as follows. (The sound will remain
muted.)
Zoom menu will appear.
There are four options
(x1.0, x1.2, x1.5 and x2.0), these are displayed
excluding the current zoom rate.
1/8x
1/16x
pause
1/16x
1/8x
1/3x
Editing
Zoom area will be displayed.
1/4x
Recording
Note
Connections
1) During playback, press [PAUSE F].
Playback will be paused and sound will be muted.
2) Press [G] repeatedly.
Playback will advance one frame (or step) at a time
when you press [G] with the sound muted.
To play back step by step backward:
Press [H] repeatedly.
Every time you press the button, the playback will go
backward by one frame.
• Press and hold [H] / [G] to reverse/ advance
continuously.
3) Press [PLAY B] to return to the normal playback.
4) Use [K / L / { / B] to select a desired zoom
position, then press [OK].
2) Press [PLAY B] to return to the normal playback.
Function Setup
Note
Zoom playback will start.
Note
Others
• When selecting a smaller factor than the current one,
the zoom area will not be displayed.
• To exit the zoom menu, press [RETURN] repeatedly
at step 3.
• To cancel the zoom function, select “x1.0” using
[K / L], then press [OK].
• You cannot slide the zoomed picture on some JPEG
files.
VCR Functions
• Forward/reverse speed will be indicated with icons
as follows.
forward (approx. speed)
1/16x:
1/8x:
1/3x:
reverse (approx. speed)
1/16x:
1/8x:
1/4x:
• Only slow forward is available when playing back
video CD.
Español
EN
63
SPECIAL PLAYBACK
Marker Setting
Repeat Playback
This feature allows you to assign a specific point on a disc
to be called back later.
1) During playback, press [DISPLAY] to bring up the
display menu.
If the display menu is already shown, skip to step 2.
2) Use [{ / B] to select
e.g.) DVD-video
to display the marker list.
1/ 5
1/ 5
0:01:00 / 1:23:45
Available repeat function may vary depending on the discs.
1) During playback press [DISPLAY] to bring up the
display menu, then proceed to step 2), or press
[REPEAT] then proceed to step 3).
If the display menu is already shown, skip to step 2.
2) Use [{ / B] to select
menu.
1/ 5
to display the selection
1/ 5
0:01:00 / 1:23:45
DVD Video
3) Use [K / L] to select a desired repeat type, then
press [OK].
The selected repeat playback will start.
DVD Video
e.g.) DVD-video
OFF
Title
Chapter
A–B
3) Use [K / L] to select a desired marker number.
When it reaches the desired point, press [OK].
e.g.) audio CD, video CD
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
1
2
3
4
5
6
OFF
-------------
Track
All
A–B
e.g.) MP3 / JPEG files
OFF
Track
All
Group
The title (track) number and the time will be displayed.
4) To return to the marker later:
Use [K / L] to select the desired marker number,
then press [OK].
Note
• To clear a marker, select the marker number to be
cleared, then press [CLEAR].
• All markers will be erased when you operate these
operations listed below.
– Opening the disc tray
– Turning the unit to standby / off
– Record on a recordable disc
• You can mark up to 6 points.
• Marker setting is not available when you play back
the video CD with PBC function.
Title:
The current title will be played back repeatedly.
Chapter:
The current chapter will be played back repeatedly.
All:
The current disc will be played back repeatedly.
A-B:
Desired section can be played back repeatedly.
1) Use [K / L] to select “A-B”, then press [OK].
2) Press [OK] at the desired starting point A.
3) Press [OK] at the desired ending point B.
Track:
The current track or file will be played back repeatedly.
Group:
The current folder will be played back repeatedly.
Note
• Point B for the repeat A-B playback should be set
within the same title or track as point A.
• To cancel the repeat playback, select “OFF” at step 3.
The repeat setting will also be cancelled when you
stop playback.
• You cannot select “Group” during the random playback.
• Repeat playback is not available when you play back
the video CD with PBC function.
• During the A-B repeat, if you reach point A using any
reverse playback, the reverse playback will be cancelled
and the A-B repeat playback resumes from point A.
64
EN
Random Playback
Program Playback
You can program the disc to play back in your desired
order.
Connections
You can play back a disc randomly instead of playing
back in the original order.
Introduction
SPECIAL PLAYBACK
1) Press [SETUP].
Note
2) Use [K / L] to select “DISC Playback Mode”, then
press [OK].
“DISC Playback Mode” menu will appear.
3) Use [K / L] to select “Program Play”, then press
[OK].
4) Use [K / L] to select a desired track, then press [OK]
or [B].
Recording
• To cancel random playback, press [STOP C] twice
during random playback. “OFF” appears on the TV
screen.
• For video CD with PBC function, the PBC setting will
be switched to off automatically when you start
random playback.
1) Press [SETUP].
Basic Setup
2) Use [K / L] to select “DISC Playback Mode”, then
press [OK].
“DISC Playback Mode” menu will appear.
For MP3, use [K / L] to select “Music”, then press [OK].
For JPEG, use [K / L] to select “Photo”, then press [OK].
3) Use [K / L] to select “Random Play”, then press
[OK].
Random playback will start.
DISC Playback Mode
Program Play
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Playback
Total
Slide Show
0:00:00
Repeat this step until you program all the desired
tracks.
You can select the display time between 5 seconds and
10 seconds.
5) Press [PLAY B].
Editing
DISC Playback Mode
1) Follow steps 1 and 2 in “Random Playback” on this
page.
Program Play
04
10
06
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
3) Use [K / L] to select the display time, then press
[OK].
Total
Function Setup
2) Use [K / L] to select “Slide Show”, then press [OK].
09
-0:31:07
Program playback will start.
4) Press [SETUP] to exit.
Note
• Large-size JPEG files take a few moments to be
displayed.
Others
• To erase tracks you selected, press [CLEAR] at step 4.
• You can make program settings up to 50 tracks.
• To cancel program playback, press [STOP C] twice
during program playback. “OFF” appears on the TV
screen.
• You may also select a desired track using [the
Number buttons] at step 4.
• For video CD with PBC function, the PBC setting will
be switched to off automatically when you start
program playback.
VCR Functions
Note
Español
EN
65
SEARCH
Title / Chapter Search
Track Search
Using [H] / [G]
Using [H] / [G]
1) During playback, press [G] to skip the current
title or chapter and move to the next.
The title or chapter will move forward by one at a time.
• If there is no chapter in one title, the current title will
be skipped.
1) During playback, press [G] to skip the current
track/file and move to the next.
The track/file will move forward one at a time.
To go back to the beginning of the current track/file,
press [H].
Press it repeatedly to go to the previous track/file. The
track/file will move backward one at a time.
For JPEG files, press it once to go to the previous file.
To go back to the beginning of the current title or
chapter, press [H].
Press it repeatedly to go to the previous title or
chapter. The title or chapter will move backward one
at a time.
Using [DISPLAY]
1) During playback, press [DISPLAY] to bring up the
display menu .
2) Use [{ / B] to select
e.g.) DVD-video
, then press [OK].
Using [DISPLAY]
1) During playback, press [DISPLAY] to bring up the
display menu.
If the display menu is already shown, skip to step 2.
2) Use [{ / B] to select
e.g.) audio CD
1/ 5
, then press [OK].
0:00:15 / 0:05:00
CD
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
e.g.) MP3 files
1/ 5
The number next to
will be highlighted.
3) Title:
Use [K / L] or [the Number buttons] to enter a
desired title number to search, then press [OK].
Title search will start.
Chapter:
for
Press [B] to move to the number next to
chapter.
Use [K / L] or [the Number buttons] to enter a
desired chapter number to search, then press [OK].
After the search, playback will start automatically.
Note
• In search mode display, total numbers of each search
contents (title/chapter/time) are shown as a
denominator.
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
total number
total time
of titles
of the title
total number
of chapters
66
EN
0:00:15
MP3
The number next to
will be highlighted.
3) Use [K / L] or [the Number buttons] to enter a
desired track/file number to search, then press
[OK].
After the search, playback will start automatically.
Note
• During CD playback you can enter a track number
directly using [the Number buttons] for track search
without displaying the menu.
• Track search using [DISPLAY] is not available when
you play back the video CD with PBC function.
Introduction
SEARCH
Time Search
Connections
1) During playback, press [DISPLAY] to bring up the
display menu.
If the display menu is already shown, skip to step 2.
2) Use [{ / B] to select
e.g.) DVD-video
1/ 5
Basic Setup
1/ 5
, then press [OK].
0:01:00 / 1:23:45
DVD Video
e.g.) audio CD
0:00:15 / 0:05:00
Recording
1/ 5
CD
The number next to
will be highlighted.
To move to the number next to
, Press [B].
and time
Playback
When time search is not available,
counter are not displayed.
3) Use [K / L / { / B] or [the Number buttons] to
enter a desired time to search, then press [OK].
After the search, playback will start automatically.
Editing
Note
• Time search is available only in the same track, file or
title.
• Time search is not available when you play back the
video CD with PBC function.
Function Setup
VCR Functions
Others
Español
EN
67
SELECTING THE FORMAT OF AUDIO AND VIDEO
You can select the format of audio and video as you prefer depending on the contents of the disc you are playing back.
Switching Subtitles
Switching Audio Soundtrack
DVD-video may have subtitles in 1 or more languages.
Available subtitle languages can be found on the disc
case. You can switch subtitle languages anytime during
playback.
1) During playback, press [DISPLAY] to bring up the
display menu.
2) Use [{ / B] to select
menu.
e.g.) DVD-video
1/ 5
to display the selection
1/ 5
0:01:00 / 1:23:45
When playing back a DVD-video recorded with 2 or more
soundtracks (these are often in different languages), you
can switch them during playback.
When playing back video CD, audio CD you can switch
“L/R”(stereo), “L”(left) or “R”(right).
1) During playback press [DISPLAY] to bring up the
display menu, then proceed to
step 2), or press [AUDIO] then proceed to step 3).
• If the display menu is already shown, skip to step 2.
2) Use [{ / B] to select
menu.
to display the selection
DVD Video
3) Use [K / L] to select a desired subtitle language,
then press [OK].
1/ 5
1/ 5
3) Use [K / L] to select a desired audio soundtrack or
audio channel, then press [OK].
For DVD-video
• Audio soundtrack will switch.
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
0:01:00 / 1:23:45
1.Dolby Digital 5.1ch English
2.Dolby Digital 2ch English
DVD Video
OFF
1.English
Subtitle will be displayed in the selected language.
When selecting “OFF”, subtitle will disappear.
Note
• Some discs will only allow you to change the subtitle
from the disc menu. Press [TITLE] or [DISC MENU] to
display the disc menu.
• If a 4-digit language code appears in the subtitle
menu, refer to “LANGUAGE CODE” on page 101.
• If the title contains both main and sub audio, you can
further select “L” (main), “R” (sub), or “L/R” (mixed of
main and sub).
For audio CD, video CD
• Audio channel will switch.
e.g.) audio CD
1/ 5
0:00:15 / 0:05:00
CD
1. L/R
2. L
3. R
Note
• Some discs will only allow you to change the
soundtrack from the disc menu. Press [TITLE] or
[DISC MENU] to display the disc menu.
68
EN
Switching Virtual Surround System
1/ 5
to display the selection
Some DVD-video have scenes shot from 2 or more
angles. Angle information should be on the disc case if
the disc contains multi-angle scenes.
1) During playback, press [DISPLAY] to bring up the
display menu.
2) Use [{ / B] to select
e.g.) DVD-video
1/ 5
, then press [OK].
1/ 5
Basic Setup
2) Use [{ / B] to select
menu.
e.g.) DVD-video
Switching Camera Angles
Connections
You can enjoy stereophonic virtual space through your
existing 2 channel stereo system.
1) During playback, press [DISPLAY] to bring up the
display menu.
If the display menu is already shown, skip to step 2.
Introduction
SELECTING THE FORMAT OF AUDIO AND VIDEO
0:01:00 / 1:23:45
DVD Video
1/ 5
0:01:00 / 1:23:45
DVD Video
1/ 5
1/ 5
0:01:00 / 1:23:45
Recording
3) Use [K / L] to select “OFF”, “Type 1” or “Type 2”,
then press [OK].
e.g.) DVD-video
Angle icon appears when a switching camera angle is
available.
Angle will switch each time you press [OK].
DVD Video
OFF
: no effect
Type 1 : natural effect
Type 2 : emphasized effect
• Select “OFF” in a case sound is distorted.
• The setting will be kept even when the unit is turned
off .
Note
• Angle icon does not appear on the TV screen in a
case you set “Angle Icon” to “OFF” in “Playback”
menu. Refer to page 87.
Reducing Block Noise
Editing
Note
Playback
OFF
Type 1
Type 2
This function reduces noise in the playback picture.
2) Use [{ / B] to select
menu.
e.g.) DVD-video
1/ 5
Function Setup
1) During playback, press [DISPLAY] to bring up the
display menu.
to display the selection
1/ 5
0:01:00 / 1:23:45
DVD Video
VCR Functions
3) Use [K / L] to select a desired option, then press
[OK].
1/ 5
1/ 5
0:01:00 / 1:23:45
DVD Video
OFF
Type 1
Type 2
Others
Your setting will be activated.
OFF
: When playing back titles with a few noises
such as DVD-video.
Type 1 : For the titles recorded in long time mode
such as EP or SLP mode.
Type 2 : Same as type 1, only more effective.
Español
EN
69
INFORMATION ON DISC EDITING
Guide to a Title List
Editing Discs
Title list allows you to check the titles recorded on the
disc easily. You can choose a title to play back from this
list and easily edit the titles as you prefer.
Press [DVD], then press [TITLE].
2
1
3
4
1
SP (2Hr)
NOV/21/09 11:00AM CH12 SP
NOV/21/09 0:20:44
Play
Edit
Overwrite
2
NOV/22/09 11:35AM CH13 EP
NOV/22/09 0:10:33
3
EMPTY TITLE
1:37:52 SP(2Hr)
6
2
Note
5
• When selecting “Edit” on pop-up menu of the title
list and edit the title, the title list is displayed after
writing the edited contents onto the disc.
• The capacity indicator in the right side of the title list
may not indicate the precise capacity in the disc.
• The capacity indicator may not indicate the capacity
for the titles of which recording time is short.
• Once you have finalized a DVD+R/ DVD-R, you
cannot edit or record anything on that disc.
Edit
Title Delete
2
Edit Title Name
Chapter Mark
Hide Chapter
Index Picture
Title Dividing
NOV/22/09 11:35AM CH13 EP
1 : 05 : 00
11 10
9
8
7
1. Title list: List of the titles recorded on the disc, and
their information.
2. Arrow: Indicating there is a previous / next page.
3. Title information: On the first line, title name
(editable) is displayed. On the second line, the date
recorded and length of the title are displayed.
Empty title: The portion of the disc where there is no
recordings are made. As for the empty title, available
recording time by the selected recording mode is
displayed on the second line.
4. Recording mode: Currently selected recording mode
is displayed here.
5. Capacity indicator: Indicating the position and the
amount of each title in the disc. The portion for the
selected title is highlighted.
6. Thumbnails: A cut from the recorded content is
displayed here.
7. Submenu: Submenus for the selected menu are
displayed here.
8. Title name (editable): If you do not name the title,
the recorded date, time, channel, and the recording
mode are displayed here.
9. Progress bar: Indicating the progress of the
playback.
10. Preview window: Preview of the selected title is
displayed here.
11. Playback status: Indicating the current playback
status of the selected title.
Press [STOP C] to exit the title list.
70
EN
You can edit discs for the following items. Be sure that
once you edit titles, they will not remain as original.
• Deleting a Title (Refer to page 71.)
• Putting Names on Titles (Refer to page 72.)
• Setting Chapter Marks (Refer to page 73.)
• Clearing Chapter Marks (Refer to pages 74-75.)
• Hiding Chapters (Refer to page 76.)
• Setting Pictures for Thumbnails (Refer to page 77.)
• Dividing a Title (DVD+RW/DVD-RW only)
(Refer to page 78.)
• Putting Name on Disc (Refer to page 79.)
• Erasing Disc (Refer to page 80.)
• Making Edits Compatible (Refer to page 81.)
Introduction
EDITING DISCS
Deleting a Title
3
Use [K / L] to select “Edit”, then
press [OK].
Play
Edit
Overwrite
Connections
You can delete a title which you do not need anymore.
Please be advised that the titles once deleted cannot be
brought back to the disc.
For DVD+RW/DVD-RW, when the last recorded title in the
title list is deleted, the available disc space to record on
will be increased. For DVD+R/DVD-R, the disc space to
record on will not be changed.
SP (2Hr)
1
NOV/21/09 11:00AM CH12 SP
NOV/21/09 0:20:44
2
NOV/22/09 11:35AM CH13 EP
NOV/22/09 0:10:33
3
Basic Setup
EMPTY TITLE
1:37:52 SP(2Hr)
Edit
1
Recording
4
Use [K / L] to select “Title Delete”,
then press [OK].
Title Delete
Edit Title Name
Chapter Mark
Hide Chapter
Index Picture
Title Dividing
NOV/21/09 11:00AM CH12 SP
Confirmation message will appear.
Edit - Title Delete
1
Editing
5
Use [K / L] to select “Yes”, then press
[OK].
Yes
No
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
Use [K / L] to select a desired title,
then press [OK].
SP (2Hr)
2
Please finalize the disc when the writing is
completed before playing back on other DVD
players.
Writing to Disc
90%
NOV/22/09 11:35AM CH13 EP
NOV/22/09 0:10:33
3
EMPTY TITLE
1:37:52 SP(2Hr)
This operation may take a
while to be completed.
1
Note
EMPTY TITLE
0:21:14 SP(2Hr)
2
NOV/22/09 11:35AM CH13 EP
NOV/22/09 0:10:33
Español
• Deleted part of the titles in the capacity indicator
changes in color.
• As for DVD+RW/DVD-RW if you delete the title, deleted
title will be displayed as “EMPTY TITLE”.
SP (2Hr)
Others
After editing is complete, the title list will appear.
e.g.) DVD+RW/DVD-RW
VCR Functions
1
NOV/21/09 11:00AM CH12 SP
NOV/21/09 0:20:44
After that, “Are you sure?” will appear, select
“Yes” and then press [OK].
Title will be deleted.
Data will be written onto the disc momentarily.
e.g.) DVD+R/DVD-RW/-R
Function Setup
1
2
Press [DVD] first.
Press [TITLE].
Playback
1 : 05 : 00
3
EMPTY TITLE
1:37:52 SP(2Hr)
EN
71
EDITING DISCS
Putting Names on Titles
You can put title names on the titles and change the
names from this menu.
4
Use [K / L] to select “Yes”, then press
[OK].
Edit - Edit Title Name
1
Yes
No
MY FAVORITE
1 : 05 : 00
The name you entered will be activated for the title.
5
After this operation is completed,
press [RETURN] to exit.
Data will be written onto the disc momentarily.
This operation may take a
while to be completed.
Guide to Edit Title Name
1
2
Follow steps 1 to 3 in “Deleting a
Title” on page 71 to display “Edit”
menu.
1) Use [K / L] to select a desired character set, then
press [OK].
2) Follow the list below, use [the Number buttons]
repeatedly until the desired letter appears.
When you finish entering a title name, press [OK].
Select
Press
Use [K / L] to select “Edit Title
Name”, then press [OK].
ABC
abc
123
<space>
<space>
0
<space>
(*1)
(*1)
1
! ”# $ % & ’( )
*+,-./:;<=>
?@[]^_{|}
ABC
abc
2
(*2)
DEF
def
3
(*2)
GHI
ghi
4
(*2)
JKL
jkl
5
(*2)
MNO
mno
6
(*2)
PQRS
pqrs
7
(*2)
TUV
tuv
8
(*2)
WXYZ
wxyz
9
(*2)
Edit
1
Title Delete
Edit Title Name
Chapter Mark
Hide Chapter
Index Picture
@!?
Title Dividing
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
3
To enter a title name, follow the
steps of “Guide to Edit Title Name”
on this page.
Edit - Edit Title Name
1
A B C
a b c
character set
1 2 3
@ !
?
*1 Press
, character set will be changed to “ @!? ” mode
automatically.
to
, character set will be changed to the
*2 Press
previous input mode automatically.
• To delete letters, press [CLEAR] repeatedly.
Holding [CLEAR] to delete all letters.
• Use [s / B] to move the cursor to the left and right.
• You can enter up to 30 letters.
M
1 : 05 : 00
area for entering title names
72
EN
Note
• Undefined letters in a title name are shown by “*”. If
you delete them, adjoining letters may change to “*”
or other.
Introduction
EDITING DISCS
Setting Chapter Marks
You can put chapter marks in each title. Once a chapter is
marked, you can use it for the chapter search feature.
Submenu will appear.
Press [PLAY B] and then [PAUSE F]
to decide the point at which you will
create a new chapter mark.
• It is convenient to use [H], [G],
[E] and [D] for finding the point to add a
new chapter mark.
Recording
Use [K / L] to select “Add”, then press
[OK].
Basic Setup
4
Use [K / L] to select “Chapter Mark”,
then press [OK].
Connections
1
2
3
Follow steps 1 to 3 in “Deleting a
Title” on page 71 to display “Edit”
menu.
Edit - Chapter Mark
1
Add
Delete
Playback
Delete All
Chapter
2/ 3
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
Editing
5
Use [K / L] to select “Yes”, then press
[OK].
Edit - Chapter Mark - Add
1
Yes
Function Setup
No
Chapter
2/ 3
F
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
A new chapter mark will be added.
Note
This operation may take a
while to be completed.
Others
• When the number of chapter marks in a title is 99
and the number of chapter marks in a disc is 254,
chapter marks cannot be added.
• Besides the above-mentioned, it is not likely to be
able to add according to recorded time and number
of chapters.
• Remaining time of the disc may decrease when
adding chapter marks or increase when clearing
chapter marks depending on the recording time or
edited contents.
VCR Functions
6
Press [RETURN] twice to exit.
Data will be written onto the disc momentarily.
Español
EN
73
EDITING DISCS
Clearing Chapter Marks
1
2
3
Follow steps 1 to 3 in “Deleting a
Title” on page 71 to display “Edit”
menu.
Use [K / L] to select “Chapter Mark”,
then press [OK].
Submenu will appear.
Use [H] / [G] to select a chapter
mark to be deleted, then press
[PAUSE F].
Chapter mark number is displayed on the
preview screen.
e.g.) DVD
Edit - Chapter Mark
1
Add
Delete
Delete All
Chapter
2/ 3
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
4
5
Use [K / L] to select “Delete”, then
press [OK].
Use [K / L] to select “Yes”, then press
[OK].
Edit - Chapter Mark - Delete
1
Yes
No
Chapter
2/ 3
F
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
The selected chapter mark will be deleted.
6
Note
• Remaining time of the disc may decrease when
adding chapter marks or increase when clearing
chapter marks depending on the recording time or
edited contents.
• You cannot delete the chapter mark 1.
74
EN
Press [RETURN] twice to exit.
Data will be written onto the disc momentarily.
This operation may take a
while to be completed.
Introduction
EDITING DISCS
Clearing Chapter Marks (cont’d)
Follow steps 1 to 3 in “Deleting a
Title” on page 71 to display “Edit”
menu.
Use [K / L] to select “Chapter Mark”,
then press [OK].
Submenu will appear.
Basic Setup
Use [K / L] to select “Delete All”,
then press [OK].
Use [K / L] to select “Yes”, then press
[OK].
Recording
1
2
3
4
Connections
To delete all chapter marks:
Edit - Chapter Mark - Delete All
Yes
Playback
1
No
Chapter
2/ 3
F
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
Editing
5
Use [K / L] to select “Yes”, then press
[OK].
Edit - Chapter Mark - Delete All
Function Setup
1
Are you sure?
Yes
No
Chapter
2/ 3
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
6
Press [RETURN] twice to exit.
Data will be written onto the disc momentarily.
This operation may take a
while to be completed.
VCR Functions
All chapter marks will be deleted.
Others
Note
Español
• Remaining time of the disc may decrease when
adding chapter marks or increase when clearing
chapter marks depending on the recording time or
edited contents.
EN
75
EDITING DISCS
Hiding Chapters
You can hide chapters from the title list.
Hidden chapters are skipped during playback.
1
2
3
4
Follow steps 1 to 3 in “Deleting a
Title” on page 71 to display “Edit”
menu.
Use [K / L] to select “Hide Chapter”,
then press [OK].
Submenu will appear.
Use [H] / [G] to decide the
chapter to be hidden.
Use [K / L] to select “Hidden”, then
press [OK].
Edit - Hide Chapter
1
Visible
Hidden
Chapter
2/ 3
Visible
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
The chapter is now hidden.
5
After this operation is completed,
press [RETURN] twice to exit.
Data will be written onto the disc momentarily.
This operation may take a
while to be completed.
If you want hidden chapters to be “Visible”,
select the chapter to be shown. Then use
[K / L] to select “Visible” at the step 4 on this
page.
Data will be written onto the disc momentarily.
After that, title list is displayed.
Note
• ”Hidden” will be displayed in the preview window
while previewing the hidden chapter.
• When you make all chapters in the title “Hidden”,
“Hidden” is displayed in a thumbnail of the title list.
1
Hidden
SP (2Hr)
NOV/21/09 11:00AM CH12 SP
NOV/21/09 0:20:44
2
NOV/22/09 11:35AM CH13 EP
NOV/22/09 0:10:33
3
EMPTY TITLE
1:37:52 SP(2Hr)
76
EN
Introduction
EDITING DISCS
Setting Pictures for Thumbnails
You can set your desired scene as a thumbnail for each
title.
Connections
Use [H], [G], [E], [D], [PAUSE
F] and [PLAY B] to decide the
picture you want to select as a
thumbnail.
Use [K / L] to select “Index Picture”,
then press [OK].
Edit - Index Picture
1
Recording
Use [K / L] to select “Yes”, then press
[OK].
Basic Setup
1
2
3
4
Follow steps 1 to 3 in “Deleting a
Title” on page 71 to display “Edit”
menu.
Yes
No
Playback
F
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
A picture for thumbnail will be set.
This operation may take a
while to be completed.
Editing
5
Press [RETURN] to exit.
Data will be written onto the disc momentarily.
Function Setup
VCR Functions
Others
Note
Español
• If the selected picture for a thumbnail is overwritten,
the thumbnail is reset to the first scene of the title.
EN
77
EDITING DISCS
Dividing a Title
You can divide one title into 2 new titles.
1
2
3
4
Follow steps 1 to 3 in “Deleting a
Title” on page 71 to display “Edit”
menu.
Use [H], [G], [E], [D], [PAUSE
F] and [PLAY B] to decide the point
at which you will divide the title.
Use [K / L] to select “Title Dividing”,
then press [OK].
Use [K / L] to select “Yes”, then press
[OK].
Edit - Title Dividing
1
Yes
No
F
NOV/21/09 11:00AM CH12 SP
1 : 05 : 00
The title will be divided into 2 new titles.
Both title names are identical, and thumbnails
are reset to the first scene at this point.
Data will be written onto the disc momentarily.
This operation may take a
while to be completed.
Note
• You cannot divide a title of the disc when the
number of recording titles reaches the maximum of
49, and the number of recording chapters reaches
the maximum of 254.
78
EN
Introduction
EDITING DISCS
Putting Name on Disc
You can put a name on the disc and change it from this
menu.
Press [STOP C] if you are playing back a disc.
Use [K / L] to select “Edit Disc
Name”, then press [OK].
Basic Setup
Use [K / L] to select “Disc Edit”, then
press [OK].
Connections
1
2
3
Press [SETUP].
e.g.) DVD+RW
Recording
Disc Edit
Edit Disc Name
Erase Disc
Make Edits Compatible
Disc Protect OFF ON
A window for entering a title name will appear.
Edit Disc Name
Playback
A B C
a b c
No Disc Name
1 2 3
DVD+RW
Total Titles
3
Disc Space Used
0:30:48
Disc Protect
OFF
Make Edits Compatible
Needed
@ !
?
To enter a disc name, follow the steps
of “Guide to Edit Title Name” on page
72.
Use [K / L] to select “Yes”, then press
[OK].
Function Setup
When you finish entering a title name, press
[OK].
Editing
Edit Disc Name
VCR Functions
4
5
Disc
Yes
No
No Disc Name
Disc
DVD+RW
Total Titles
3
Disc Space Used
0:30:48
Disc Protect
OFF
Make Edits Compatible
Needed
MY FAVORITE DISC
This operation may take a
while to be completed.
Others
The name you entered will be activated for the title.
Data will be written onto the disc momentarily.
Note
Español
• You cannot select “Disc Edit” when finalized DVD+R
or DVD-R is inserted.
EN
79
EDITING DISCS
Erasing Disc
You can erase all titles on a disc.
Press [STOP C] if you are playing back a disc.
1
2
Follow steps 1 to 2 in “Putting Name
on Disc” on page 79 to display “Disc
Edit” menu.
Use [K / L] to select “Erase Disc”,
then press [OK].
e.g.) DVD+RW
Disc Edit
Edit Disc Name
Erase Disc
Make Edits Compatible
Disc Protect OFF ON
3
Use [K / L] to select “Yes”, then press
[OK].
When you press “Yes”, all the
contents in the disc will be erased.
Are you sure to erase the disc?
Yes
No
Data will be written onto the disc momentarily.
This operation may take a
while to be completed.
The contents of the disc is now deleted.
Note
• When you select “Yes” at step 3, all contents of the
disc will be erased.
80
EN
Introduction
EDITING DISCS
Making Edits Compatible
Press [STOP C] if you are playing back a disc.
1
2
Follow steps 1 to 2 in “Putting Name
on Disc” on page 79 to display “Disc
Edit” menu.
3
Use [K / L] to select “Yes”, then press
[OK].
Basic Setup
Use [K / L] to select “Make Edits
Compatible”, then press [OK].
Connections
If you have added or deleted chapters, or made chapters
hidden, you must perform “Make Edits Compatible” to
see those effects on other unit.
Disc Edit
Edit Disc Name
Erase Disc
Make Edits Compatible
Disc Protect OFF ON
Recording
Playback
Activate the Make Edits Compatible?
Yes
No
Data will be written onto the disc momentarily.
Editing
This operation may take a
while to be completed.
Function Setup
VCR Functions
Others
Español
EN
81
LIST OF SETTINGS
The following table is the contents which you can set and the default setting.
Refer to the following table for useful operation.
Setup
Items (highlight is the default)
Playback
Parental Lock
Pages 85-87
Disc Audio
Dynamic Range
Control
PCM
Dolby Digital
Disc Menu Language
Audio Language
Subtitle Language
Angle Icon
General Setting
Still Mode
OSD Language
Display
Pages 88-90
Français
Español
OFF
1minute
5minutes
10minutes
15minutes
Auto
Bright
Dark
Screen Saver
FL Dimmer
DTV CC
Caption Service
page 36
Set the brightness of the front panel display.
Set the type of the DTV closed caption.
ON
OFF
Set the CC style setting whether or not is
effective.
Font Size
Large
Middle
Small
Set font size of the displayed caption.
Font Style
Style1
Style2
Style3
Style4
Style5
Style6
Style7
Style8
Set font style of the displayed caption.
Font Opacity
Solid
Transparent
Translucent
Flash
Set the font opacity of the displayed caption.
CC Style
User Setting
pages 37-38
EN
Set the idling time before the screen saver
starts.
OFF
Service1
Service2
Service3
Service4
Service5
Service6
ON
OFF
Recording
page 40
82
Contents
Set the parental level for DVD playback.
OFF
level 8 [Adult] to 1 [Kid Safe]
Compressing the range of sound volume.
ON
OFF
Set whether the sound recorded in 96kHz will
48kHz
be down sampled in 48kHz.
96kHz
PCM
Set the type of sound signal which outputs
from the digital audio output jack.
Stream
Set the language for disc menu language.
English
French
Spanish
Other
Set the language for audio.
Original
English
French
Spanish
Other
Set the language for subtitles.
OFF
English
French
Spanish
Other
Set whether or not to display the angle icon.
ON
OFF
Set the type of still image in pausing playback.
Auto
Field
Frame
Set the language for OSD (on-screen display).
English
Set whether to record the DTV closed caption
or not.
Setup
Items (highlight is the default)
Display
CC Style
Font Color
Pages 88-90
pages 37-38
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
Set the viewing limitation according to
Canadian French language ratings.
To set the rating.
Clear the downloadable rating information
and its setting.
Change the password.
Set to the progressive scan mode (set to "ON")
or to the interlace scan mode (set to "OFF").
Set a picture size according to aspect ratio of
your TV.
EN
83
Español
TV Aspect
Set the viewing limitation according to
Canadian English language ratings.
Others
ON
OFF
Set the viewing limitation according to US TV
program ratings.
VCR Functions
Progressive Scan
General Setting
Set the viewing limitation according to US
movie ratings.
Function Setup
Video
Page 91
Set back color of the displayed caption.
Editing
Change
Password
Set back opacity of the displayed caption.
Playback
V-Chip
Solid
Transparent
Translucent
Flash
Back Color
White
Black
Red
Green
Blue
Yellow
Magenta
Cyan
MPAA Rating
X
NC-17
R
PG-13
PG
G
NR
TV Rating
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
None
Canadian
18+
English Rating
14+
PG
G
C8+
C
E
Canadian French 18ans+
Rating
16ans+
13ans+
8ans+
G
E
Downloadable
Block Setting
Rating
Clear Downloadable
Rating
Set edge color of the displayed caption.
Recording
Back Opacity
Set edge type of the displayed caption.
Basic Setup
Edge Color
None
Raised
Depressed
Uniform
L.Shadow
R.Shadow
White
Black
Red
Green
Blue
Yellow
Magenta
Cyan
Contents
Set the font color of the displayed caption.
Connections
Edge Type
White
Black
Red
Green
Blue
Yellow
Magenta
Cyan
Introduction
LIST OF SETTINGS
LIST OF SETTINGS
Setup
Video
Page 91
Items (highlight is the default)
Video Input
L1(Rear)
Page 49
Video In
S-Video In
Contents
Set the video input type for the external input.
General Setting
L2(Front)
Video In
S-Video In
OFF
Recording
Auto Chapter
Page 40
5 minutes
10 minutes
15 minutes
30 minutes
60 minutes
Auto Finalize
Disc Full
ON
Page 55
OFF
End of Timer Rec ON
OFF
Pages 51-52
Dubbing Mode
VCR DVD
DVD VCR
Make Recording Compatible
ON
Page 40
OFF
Clock
Clock Setting
Pages 31-32 Auto Clock Setting
OFF
Auto
Manual
Daylight Saving Time
ON(MAR-NOV)
ON(APR-OCT)
OFF
Channel
Auto Channel Preset
Antenna
Pages 28-30
Cable (Analog)
Cable (Analog / Digital)
Manual Channel Preset
TV Audio Select
Stereo
Page 35
SAP
HDMI
Format
RGB
Page 92
YCbCr
HDMI Audio
ON
OFF
RGB Range
Normal
Enhanced
Page 93
Yes
Reset All
No
Insert chapter marks at even time intervals.
Set the unit to finalize the disc automatically.
Set the dubbing direction.
Set to prohibit additional recording (OFF) or
to replace the title list after recording (ON).
Set the clock.
Set the clock automatically.
Set the clock for the daylight saving time.
Tune the channels automatically.
Tune the channels manually.
Set the analog TV audio type for output and
recording.
Set the color format for the HDMI output.
Set whether to output the HDMI audio signal
or not.
Set the black-white contrast level for HDMI
RGB output.
Set to the default setting.
Note
• Your change to each setting stays on even when the power is off except for Dubbing Mode.
• An item which is not currently available is grayed in the settings.
84
EN
Introduction
SETUPS
Playback
Press [STOP C] if you are playing back a disc.
“General Setting” menu will appear.
Use [K / L] to select “Playback”, then
press [OK].
General Setting
Recording
Playback
Display
Video
Recording
Clock
Channel
HDMI
Reset All
Playback
Use [K / L] to select a desired item,
then press [OK].
1
2
3
4
5
6
7
Parental Lock
Disc Audio
Disc Menu Language
Audio Language
Subtitle Language
Angle Icon
Still Mode
Refer to 1 to 7 on pages 86-87 and
set the selected item.
Editing
Submenu will appear.
Function Setup
4
5
Basic Setup
3
Connections
1
2
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
When you finish with setting, press
[SETUP] to exit.
VCR Functions
Others
Español
EN
85
SETUPS
Playback (cont’d)
1
Parental Lock (Default: OFF)
Some DVD-video feature a parental lock level. Playback
will stop if the ratings exceed the levels you set, it will
require you to enter a password before the disc will
playback. This feature prevents your children from
viewing inappropriate material.
Use [K / L] to select the desired level, then press [OK].
Parental Lock
Note
• Press [CLEAR] to erase numbers entered incorrectly.
• When you forget the password or you want to clear
all settings in “Parental Lock” menu, enter 4737 using
[the Number buttons] in password input window.
Password will be cleared and parental levels will be
set to “OFF”.
2
OFF
8 [Adult]
7 [NC 17]
6 [R]
5 [PG R]
4 [PG 13]
3 [PG]
2 [G]
1 [Kid Safe]
Disc Audio
Choose the appropriate audio setting for your external
device.
It will only affect a disc playback.
Use [K / L] to select a desired item, then press [OK].
Disc Audio
A
B
C
If a password has not been set yet, proceed to A .
If a password has been set already, proceed to B .
Note
• Parental lock function may not be available to some
discs.
• With some DVD, it may be difficult to find if they are
compatible with parental lock. Be sure to check if the
parental lock function operates in the way that you
have set.
• Record the password in case you forget it.
• If there is a DVD in the unit when you set up the
parental lock, press [OPEN/CLOSE A] to activate the
parental lock level.
A
A
Dynamic Range Control
PCM
Dolby Digital
Dynamic Range Control (Default : ON)
Set to “ON” to compress the range between soft and loud
sounds.
Use [K / L] to select a setting, then press [OK].
Dynamic Range Control
ON
OFF
Your setting will be activated.
Note
A password has not been set yet.
Use [K / L] to select “Yes”. Use [the Number buttons] to
enter a new password except for 4737, then press [OK].
Change Password?
Yes
No
Password Input
Yes
• Dynamic range control function is available only on
the discs which are recorded in the Dolby Digital
format.
B
PCM (Default : 48kHz)
Use [K / L] to select a setting, then press [OK].
Your setting will be activated.
PCM
B
A password has been set already.
• Use [the Number buttons] to enter the current
password.
Password Input
Your setting will be activated.
• If you want to change password, use [K / L] to select
“Yes”. Use [the Number buttons] to enter a new
password except for 4737, then press [OK].
<change the password>
Change Password?
Yes
No
Password Input
Yes
Your setting will be activated.
86
EN
48kHz
96kHz
Your setting will be activated.
48kHz : If your amplifier/decoder is NOT compatible
with 96kHz PCM, select “48kHz”. 96kHz sound
will be output in 48kHz.
96kHz : If your amplifier/decoder is compatible with
96kHz PCM, select “96kHz”. 96kHz sound will
be output.
Note
When playing back disc with copyright protection
• Even if you select “96kHz”, the sound will be down
sampled at 48kHz.
Playback (cont’d)
C
Dolby Digital (Default : Stream)
If “Other” is selected for 3 to
using [the Number buttons].
Dolby Digital
Code Input
PCM
Stream
3
Disc Menu Language (Default : English)
-
-
-
• When you finish entering the code, press [OK]. Refer
to the language code table on page 101.
Note
• Only the languages supported by the disc can be
selected.
• Audio language setting may not be available to
some discs.
• You can change or switch off the subtitles on a DVD
also from the disc menu if it is available.
• Press [CLEAR] or [s] to erase numbers entered
incorrectly.
Recording
Set the language for disc menu.
Use [K / L] to select a setting, then press [OK].
-
Basic Setup
Your setting will be activated.
PCM
: Converts the Dolby Digital into PCM (2 channel).
When your amplifier/decoder is NOT
compatible with Dolby Digital, set to “PCM”.
Stream : Outputs Dolby Digital signals
When your amplifier/decoder is compatible
with Dolby Digital, set to “Stream”.
5 , press 4-digit code
Disc Menu Language
Your setting will be activated.
4
6
Angle Icon (Default : ON)
Set to “ON” to show the angle icon during the playback.
Use [K / L] to select a setting, then press [OK].
Angle Icon
Audio Language (Default : Original)
Set the audio language.
Use [K / L] to select a setting, then press [OK].
Your setting will be activated.
7
Still Mode (Default : Auto)
Select “Auto” usually.
Use [K / L] to select a setting, then press [OK].
Still Mode
Your setting will be activated.
• When “Original” is selected, the audio language will be
in the disc’s default language.
5
Subtitle Language (Default : OFF)
Subtitle Language
OFF
English
French
Spanish
Other
Your setting will be activated.
Auto
: Optimum resolution setting (“Field” or
“Frame”) will be selected.
Field
: Images in the still mode will be stabilized.
Frame : Images in the still mode will be highly defined.
Note
• Frame is 1 completed video image made up of 2
fields (There are 30 frames per second of NTSC video).
Others
Your setting will be activated.
VCR Functions
Set the subtitle language.
Use [K / L] to select a setting, then press [OK].
Auto
Field
Frame
Function Setup
Original
English
French
Spanish
Other
ON
OFF
Editing
Audio Language
Playback
English
French
Spanish
Other
Connections
Use [K / L] to select a setting, then press [OK].
Introduction
SETUPS
Español
EN
87
SETUPS
Display
Press [STOP C] if you are playing back a disc.
1
2
3
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
Use [K / L] to select “Display”, then
press [OK].
Use [K / L] to select a desired item,
then press [OK].
1
2
3
4
5
6
OSD Language
Screen Saver
FL Dimmer
DTV CC
CC Style
V-Chip
Selection menu will appear.
4
5
1
Refer to 1 to 6 on pages 88-90 and
set the selected item.
• For 4 and 5 refer to pages 36-38.
When you finish with setting, press
[SETUP] to exit.
OSD Language (Default : English)
Set the language for the on-screen display.
Use [K / L] to select a setting, then press [OK].
OSD Language
English
Français
Español
Your setting will be activated.
2
Screen Saver (Default : 10 minutes)
Set the time to activate the screen saver function on the
TV screen.
Use [K / L] to select a setting, then press [OK].
Screen Saver
OFF
1 minute
5 minutes
10 minutes
15 minutes
Your setting will be activated.
88
EN
Introduction
SETUPS
Display (cont’d)
3
FL Dimmer (Default: Bright)
FL Dimmer
Auto
Bright
Dark
6
V-Chip
V-Chip
MPAA Rating
TV Rating
Canadian English Rating
Canadian French Rating
Downloadable Rating
Change Password
Note
MPAA Rating
X
NC-17
R
PG-13
PG
G
NR
[MPAA Rating]
Rating
Category
X
Mature audience only
NC-17
No one under 17 admitted
R
Restricted; under 17 requires
accompanying parent or adult guardian
PG-13
Unsuitable for children under 13
PG
Parental guidance suggested
G
General audience
NR
No rating
higher
lower
[TV Rating]
Rating
Category
TV-MA
Mature audience only
TV-14
Unsuitable for children under 14
TV-PG
Parental guidance suggested
TV-G
General audience
TV-Y7
Appropriate for all children 7 and older
TV-Y
Appropriate for all children
None
No rating
higher
lower
VCR Functions
• When you record a TV program blocked by the
v-chip settings on the cassette tape, the audio/video
signal of the blocked part cannot be recorded
properly. No audio/video signal will be output when
playing back that part.
• When you press [DISPLAY] while playing back the
blocked part on the cassette tape, the counter
display will not be shown properly. This is not a
malfunction.
1) Use [K / L] to select the desired rating, then press
[OK] repeatedly to switch between view and block.
When it is blocked a key icon will appear.
e.g.) MPAA rating
Function Setup
A
B
C
D
E
F
You can set the viewing limitation according to MPAA
rating (US movie ratings), TV Rating (US TV program
ratings), Canadian English Rating (Canadian English
language Ratings) , Canadian French Rating (Canadian
French language Ratings).
Editing
2) Use [K / L] to select a desired item, then press [OK].
Canadian French Rating
Playback
Password Input
Canadian English Rating
Recording
With the V-chip system in this unit, you can set the
viewing limitation for the analog/digital TV programs
received from the tuner or recorded on DVDs to prevent
your children from watching inappropriate programs. If
the unit detects a blocked program, a restriction message
appears and you are not allowed to view or record the
program.
1) Use [the Number buttons] to enter the access
password.
If you have not set the password, first, use [the Number
buttons] to set the access password, then press [OK].
The number you entered will be stored as the access
password.
TV Rating
Basic Setup
You can choose one from “Auto”, “Bright” and “Dark”.
If “Auto” is selected, the display gets dark when the
power is in the standby mode.
MPAA Rating
Connections
Set the front panel display brightness.
Use [K / L] to select a setting, then press [OK].
A
B
C
D
[Canadian English Rating]
Category
Adult audience only
14+
Unsuitable for ages under 14
PG
Parental guidance suggested
G
General audience
C8+
For children over 8
For all children
E
Exempt program
lower
EN
89
Español
C
higher
Others
Rating
18+
SETUPS
Display (cont’d)
[Canadian French Rating]
Rating
E
Category
18 ans+
Adult audience only
16 ans+
Unsuitable for ages under 16
13 ans+
Unsuitable for ages under 13
8 ans+
Unsuitable for ages under 8
G
General audience
E
Exempt program
higher
TV Rating
V
S L
D
TV-MA
TV-14
TV-PG
TV-G
TV-Y7
TV-Y
None
Sub Rating
Category
Rating
FV
Fantasy Violence
TV-Y7
V
Violence
S
Sexual Situation
L
Coarse Language
TV-PG
TV-14
TV-MA
D
Suggestive Dialogue
TV-PG, TV-14
Note
• Changing the main rating to block or view
automatically changes all its sub ratings to the same
(block or view).
90
EN
Set the rating system via digital broadcasting, or clear the
downloaded ratings.
If the broadcasting signal does not have the
downloadable rating information, the message below
will appear.
lower
As for TV Rating’s TV-MA, TV-14, TV-PG, or TV-Y7, you
can further set the sub ratings to block specific
elements of programming. Press [K / L/ { / B] to select
the desired rating or sub rating, then press [OK]
repeatedly to switch between view and block. Sub
rating status will appear on the side of the main rating.
FV
Downloadable Rating
Downloadable Rating is currently not available.
• This message will also appear when you try to access
“Downloadable Rating“ after you have cleared the
downloadable rating information, and the new information has
not been downloaded since.
To set the rating:
Use [K / L] to select “Block Setting” then press [OK] to
show the various types of ratings. Use [K / L] to select
a desired rating to set, then press [OK] to show the
levels for the rating. Use [K / L] to select a level, then
press [OK] to switch between view or block. If you set
one level to block, a key icon will appear and all the
higher levels will be blocked automatically.
To clear the downloadable rating information and its
setting:
Use [K / L] to select “Clear Downloadable Rating”, then
press [OK].
F
Change Password
Change the current password.
Use [the Number Buttons] to enter new access
password.
Note
• When you forget the access password at step 1),
enter 4737 using [the Number buttons] in the
password input window. Password will be cleared.
• Depending on the type of rating system, you may set
the levels individually.
Introduction
SETUPS
Video
1
Progressive Scan (Default : OFF)
1) Use [K / L] to select “ON“, then press [OK].
Connections
This unit is compatible with the progressive scan system.
The feature provides you with the higher definition
images than the traditional output system does. To utilize
this feature, you must set progressive scan mode to “ON”.
Progressive Scan
Basic Setup
ON
OFF
2) Use [{ / B] to select “Yes“, then press [OK].
Activating progressive scan:
Check your TV has progressive scan
and connect with component video cable.
Recording
NOTE :
If there is no picture or picture is
distorted after selecting “Yes”,
Wait about 15 seconds for auto recovery.
Activate?
Yes
No
Playback
3) Use [K / L] to select “Yes“ within 15 seconds, then
press [OK].
Your setting will be activated.
Note
Press [STOP C] if you are playing back a disc.
1 Progressive Scan
2 TV Aspect
3 Video Input
Submenu will appear.
When you finish with setting, press
[SETUP] to exit.
TV Aspect (Default: 4:3 Letter Box)
You can select the TV aspect ratio to match the formats of
what you are playing back or watching digital TV
broadcasting with the unit and your TV screen (4:3
standard or 16:9 widescreen TV).
Use [K / L] to select a setting, then press [OK].
TV Aspect
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
EN
91
Español
If you have a standard TV:
Select “4:3 Letter Box”, so that black bars appear on the
top and bottom of the TV screen when playing back a
wide-screen picture. Select “4:3 Pan & Scan” for a full
height picture with both sides trimmed when playing
back wide-screen picture.
If you have a widescreen TV:
Select “16:9 Wide”.
Others
4
5
Refer to 1 to 2 on this page and set
the selected item.
• For 3 refer to page 49.
2
VCR Functions
Use [K / L] to select a desired item,
then press [OK].
Function Setup
Use [K / L] to select “Video”, then
press [OK].
Editing
1
2
3
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
• If your TV is compatible with progressive scan (525p /
480p), you are recommended to use the HDMI or
component video cable (commercially available) to
connect this unit to the TV. (Refer to pages 16-17.) If
not, use the RCA video cable and set the progressive
scan to “OFF” or press and hold [SETUP] for more
than 3 seconds during DVD playback.
• When selecting “No” or not pressing any buttons on
the unit or remote control within 15 seconds at step 3,
progressive scan remains to be “OFF” (interlace scan).
SETUPS
HDMI
3
Use [K / L] to select a desired item,
then press [OK].
4
When you finish with the setting,
press [SETUP] to exit.
1
1 Format
2 HDMI Audio
3 RGB Range
Format (Default : RGB)
You can select the color space for HDMI output.
Set the appropriate color space for your display device.
Use [K / L] to select a setting, then press [OK].
• When the connected device is not compatible with the
Y/Cb/Cr, HDMI signal is output as RGB regardless of the
setting.
Format
RGB
YCbCr
Your setting will be activated.
2
HDMI Audio (Default : ON)
If you do not want to output the audio through HDMI
(when you digitally output the audio through the
COAXIAL DIGITAL AUDIO OUT jack to your audio system,
etc.), you can set the HDMI audio output off.
Use [K / L] to select a setting, then press [OK].
• Set to “OFF” when the HDMI sound is not output.
HDMI Audio
ON
OFF
Your setting will be activated.
1
2
Press [SETUP] in stop mode and use
[K / L] to select “General Setting”,
then press [OK].
Use [K / L] to select “HDMI”, then
press [OK].
General Setting
Playback
Display
Video
Recording
Clock
Channel
HDMI
Reset All
• You cannot select HDMI when an HDMI cable is
not connected and the items are shown in grey
color.
92
EN
3
RGB Range (Default : Normal)
You can adjust the RGB range to make the dark areas of
the HDMI images brighter.
Use [K / L] to select a setting, then press [OK].
• Select “Enhanced“ if the black-white contrast is not clear.
• This setting is effective only for HDMI RGB output.
RGB Range
Normal
Enhanced
Your setting will be activated.
Introduction
SETUPS
Reset All
Reset the setting to default.
“General Setting” menu will appear.
Use [K / L] to select “Reset All”, then
press [OK].
Reset to factory default?
Recording
Yes
No
4
Basic Setup
Select “Yes” using [K / L] , then press
[OK].
Connections
1
2
3
Press [SETUP] and use [K / L] to
select “General Setting”, then press
[OK].
Select “Yes” again using [K / L] ,
then press [OK].
Are you sure?
Playback
Yes
No
Your setting in recording will be initialized.
Editing
Function Setup
VCR Functions
Others
Note
Español
• The settings listed below will remain unchanged
even after resetting to the factory default.
– OSD language setting
– Channel setting
– Clock setting
– Parental lock setting
– V-chip setting
– Timer programming information
EN
93
VCR FUNCTIONS
Information on VCR Functions
Caution on using S-video, component, or HDMI connection for VCR:
• Only the playback audio / video are available with these connections.
• Under the condition listed below, the playback image cannot be viewed. Use the standard video connection, in such case;
- during DVD recording.
• HDMI video resolution cannot be changed when the unit is in VCR mode.
Playback
Recording
Press [VCR] first.
Press [VCR] first.
1) Insert a prerecorded tape (refer to page 26 on how
to insert a cassette tape).
1) Insert a recordable tape with an erase-protection
tab intact.
Accidental erasure prevention
To prevent accidental recording on a
recorded cassette tape, remove its eraseprotection tab. To record on it later, cover
erase-protection tab
the hole with cellophane tape.
2) Press [PLAY B] to start playback.
3) Press [STOP C] to stop playback.
To pause playback:
Press [PAUSE F].
Playback will pause and sound will be muted.
To resume playback:
Press [PLAY B].
Note
• When a cassette tape without erase-protection tab is
inserted, the unit will start playback automatically.
• Tracking will be automatically adjusted upon
playback. To adjust the tracking manually, press
[CHANNEL / ] on the remote control.
• S-VHS cassette tape is not available on this unit.
• Playback will stop when you change the output mode.
2) Select the recording mode using [REC MODE].
• The desired recording mode is selected in SP
(standard play) or SLP (super long play) mode by
pressing [REC MODE].
Recording mode:
Tape speed
Type of tape
Recording / playback time
T60
T120
T160
SP mode
1hour
2hours
2-2/3hours
SLP mode
3hours
6hours
8hours
3) Select stereo or SAP. Refer to page 35.
4) Select the desired channel to record using
[CHANNEL / ] or [the Number buttons].
5) Press [REC] to start recording.
Press [STOP C] to stop the recording.
To pause recording:
Press [PAUSE F].
To resume recording:
Press [PAUSE F] or [REC].
After the unit has been in pause mode for 5 minutes, it
will stop automatically to protect the tape and the
video head from damage.
• Refer to pages 43-46 for instructions on timer recording.
Note
• This function is available only when the unit is
connected by the VIDEO OUT jack.
94
EN
One-touch Timer Recording (OTR)
Press [VCR] first.
1) Insert a recordable tape with an erase-protection
tab intact.
An index mark will be assigned at the beginning of each
recording you make. You may skip to a specific marked
point by following the steps below.
Press [VCR] first.
1) Press [SEARCH] so that “INDEX SEARCH” menu
appears.
Basic Setup
2) Select the recording mode using [REC MODE].
(Refer to “Note for DVD to VCR duplication” on page 52
and “Recording” on page 94.)
Index Search
Connections
This feature allows you to set the recording length simply
by pressing [REC] on the remote control.
Introduction
VCR FUNCTIONS
2) Using [the Number buttons], enter the number of
recordings you wish to skip within 30 seconds.
INDEX SEARCH
03
3) Select stereo or SAP. Refer to page 35.
Recording
4) Select the desired channel to record using
[CHANNEL / ] or [the Number buttons].
5) Press [REC] to begin the one-touch timer recording.
You can select a fixed recording time by pressing
[REC] repeatedly.
(8:00)
(0:30)
(1:00)
(7:30)
CURRENT PROGRAM
Beginning
of tape
When the one-touch timer recording is finished, the
unit will turn to the standby mode automatically.
Pro.1
01
Pro.3
01
End
of tape
Pro.4
02
Pro.5
03
Editing
02
To change the recording length during the onetouch timer recording:
Press [REC] repeatedly until the desired length appear.
Pro.2
Playback
(Normal recording)
3) Press [E], [D] to start index search.
If you want to go in the forward direction, press [D].
If you want to go in the reverse direction, press [E].
After index search, the VCR will play back the cassette
tape automatically.
INDEX MARK
Note
• You can make the index mark up to 20.
• This function is available only when the unit is
connected by the VIDEO OUT jack.
Function Setup
To cancel the one-touch timer recording within the
specified time:
Press [STOP C].
Note
VCR Functions
• The remaining recording time will be displayed on the
front panel display during one-touch timer recording.
Press [DISPLAY] to see it on the TV screen.
• You cannot pause the one-touch timer recording.
• If VCR one-touch timer recording is completed during
DVD playback or recording, the VCR will be in stop
mode and the DVD keeps the current mode.
• Unlike a timer recording, you can perform the following
operations during the one-touch timer recording.
- Turning the power to the standby mode to stop onetouch timer recording.
- Using [REC] or [STOP C] on the remote control.
• When the one-touch timer recording is finished and the
power is in the standby mode, the unit will switch to
the timer standby mode automatically if a timer
recording has been programmed. Press [TIMER SET] to
cancel the timer standby mode for using the unit
continuously.
• This function is available only when the unit is
connected by the VIDEO OUT jack.
Others
Español
EN
95
VCR FUNCTIONS
Time Search
This feature allows you to go to a specific point on a
cassette tape by entering the exact amount of time you
wish to skip in order to reach the point.
Press [VCR] first.
1) Press [SEARCH] repeatedly so that “TIME SEARCH”
menu appears.
2) Using [the Number buttons], enter your desired
time to skip within 30 seconds.
You can set the time up to 9:59.
TIME SEARCH
2:50
3) Press [E], [D] to start time search.
If you want to go in the forward direction, press
[D].
If you want to go in the reverse direction, press
[E].
After time search, the unit will play back the cassette
tape automatically.
Note
• Index search and time search are not available
during recording.
• Press [STOP C] to stop the search.
• If the end of the cassette tape is reached during
search, this unit will cancel the search and rewind the
cassette tape.
• This function is available only when the unit is
connected by the VIDEO OUT jack.
Other Operations
Press [VCR] first.
Fast forward:
When the unit is in stop mode, press [D] to fast forward
the cassette tape.
Rewind:
When the unit is in stop mode, press [E] to rewind the
cassette tape.
To cue or review picture during playback (picture search):
Press [E], [D] during playback.
Press it again and the unit will search in super high
speed. (in the SLP mode only)
To freeze the picture on TV screen during playback
(still mode):
Press [PAUSE F]. Each time you press the button, the
picture will be forwarded by one frame.
If the picture begins to vibrate vertically during the still
mode, stabilize the picture by pressing [CHANNEL / ]
on remote control.
If the picture is distorted or rolling vertically, adjust the
vertical hold control on your TV, if equipped.
Counter reset:
Press [CLEAR] to reset the counter to “0:00:00”.
To playback in slow motion:
Press [PAUSE F] during playback, then press [D].
Press [D] or [E] repeatedly to select the desired
speed.
Automatic rewind:
When a cassette tape is played back or fast forwarded to its
end, the cassette tape will rewind to the beginning, stop
and eject itself.
When you playback a cassette tape recorded in Hi-Fi
stereo:
Press [AUDIO] on the remote control to select Hi-Fi or
MONO for playback sound mode.
• If you have connected a stereo TV to this unit, select “HIFI”.
• If you have connected a monaural TV to this unit, select
“MONO”.
Your Selection
HIFI
MONO
Type of recorded tape
L-channel
R-channel
non Hi-Fi tapes
Monaural
Monaural
Monaural
Hi-Fi tapes
recorded in
Hi-Fi stereo
L
R
L+R
Hi-Fi tapes
recorded main
audio program
Main audio
program
Main audio
program
Main audio
program
Hi-Fi tapes
recorded second
audio program
Second audio
program
Second audio
program
Second audio
program
Note
• Still/slow mode will stop after 5 minutes to prevent
damage to the cassette tape and the video head.
• To return to playback from the picture search/still/
slow mode, press [PLAY B].
96
EN
Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing.
Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.
Remedy
• Check that the AC power cord is connected securely.
• Check the breaker (in case of power failure).
• Press [TIMER SET] to cancel the timer standby mode.
There is no picture.
• Re-connect the connecting cords securely.
• Check if the connecting cords are damaged.
• Check the connection to your TV (pages 15-20).
• Switch the input selector on your TV (such as to “L1”) so that the signal
from the unit appears on the TV screen.
TV program reception does not fill the • Try to set the channels with “Auto Channel Preset” or “Manual Channel
TV screen.
Preset” in “Channel” menu (pages 28-29).
• Select a channel of any TV program using [CHANNEL / ].
TV program pictures are distorted.
• Adjust TV antenna.
• Adjust the picture. (Refer to the TV’s instruction manual.)
• Place the unit and TV farther apart.
• Place the TV and any bunched RF coaxial cables farther apart.
TV channels cannot be changed.
• Switch the input to TV.
• Connect the RF coaxial cable correctly (pages 15-20).
There is no sound or the sound is
• Re-connect all connections securely.
distorted.
• Check if the connecting cord is damaged.
• Check the connections to the amplifier input.
• Check if the input device setting on the amplifier is correct.
• When the unit is in pause mode or in slow-motion playback mode,
sound is not output. This is not a malfunction.
• When the unit is in fast forward or fast reverse mode, sound is not
output. This is not a malfunction.
• While the setup menu or timer programming display is shown, or while
the screen saver is active, the audio is muted.
The remote control does not function. • Batteries are weak.
• There are obstacles between the remote control and the unit.
• The remote control is far from the unit.
• There are no batteries in the remote control.
• Check if the unit is turned on.
• Check if you are pointing the remote control at the recorder and NOT the TV.
If you have a plasma TV, it may interfere with the IR signal. Try the
remote with the plasma off. If the remote works, you may need to move
the unit away from the plasma TV.
• Press [DVD] or [VCR], whichever you need. Then, try again.
• Press [TIMER SET] to cancel the timer standby mode.
Time jumps/Auto Clock set’s incorrect • Set the “Auto Clock Setting” to “OFF” on page 30-31 and try “Manual
time.
Clock Setting” on page 32.
The unit does not operate properly.
• When static electricity, etc., causes the unit to operate abnormally,
unplug the unit and then plug it in again.
No analog TV closed captions are
• If you are using HDMI connection to watch the TV programs through
output.
this unit, analog TV closed caption cannot be output. Try using another
output connection to the TV.
Introduction
TROUBLESHOOTING
VCR Functions
Others
DVD • VCR
Function Setup
Español
97
Editing
EN
Playback
• There was a power failure during recording.
• The unit’s internal clock stopped due to a power failure that lasted for
more than 30 seconds. Reset the clock (pages 30-32).
• The program contains copy protection signals that restricts copying.
• The timer setting overlapped with another setting that has priority.
Timer recording is not complete or did • The timer setting overlapped with another setting that has priority (page 46).
• Disc space was not enough.
not start from the beginning.
Timer recording is impossible.
appears on the front panel display of this unit. If not, press
• Make sure
[TIMER SET].
Recording
The channel cannot be changed from
the channel you are recording.
Nothing was recorded even though
you set the timer setting correctly.
• Keep devices which may cause electrical disturbances, such as a cellular
phone, etc away from unit.
• Set the TV’s input to “TV.”
Basic Setup
Playback picture is distorted.
Connections
GENERAL
The power does not turn on.
TROUBLESHOOTING
DVD • VCR
Symptom
No image from HDMI connection.
There is no sound or the sound is
distorted.
Setup menu cannot be called up.
There is no picture.
Picture noise appears.
There is no sound.
DVD
Sound is noisy.
No DTS sound is output.
The disc does not play back.
Discs recorded on this unit cannot be
played back on other DVD players.
The disc does not start playback from
the beginning.
The unit starts playing back the disc
automatically.
Some functions such as stop, search,
or slow-motion playback cannot be
performed.
The language for the sound track
cannot be changed.
The subtitle language cannot be
changed or turned off.
The angles cannot be changed.
Recording does not stop immediately
after you press [STOP C].
98
EN
Remedy
• Check the HDMI connection. (Check the status of the HDMI related
indications.)
• Check whether the connected monitor device or other device supports
HDCP. (This unit will not output a video signal unless the other device
supports HDCP.)
• Check the setting of HDMI.
• Check whether the output format of this unit (HDMI FORMAT) matches
the supported input format of other connected device.
• If the unit is connected to the unauthorized display device with an
HDMI cable, the audio/video signal may not be output when playing
back a commercial DVD-video.
• The HDMI sound is not output when “HDMI Audio” is set to “OFF”.
• Check the RCA audio cable connection. If you are using HDMI-DVI
conversion cable, you must connect the RCA audio cable, too.
• Check whether the output format of this unit (HDMI FORMAT) matches
the supported input format of other connected device.
• Setup menus cannot be called up during DVD recording or DVD playback.
• If the main menu appears on the TV screen, press [RETURN] to exit.
• Check if the progressive scan mode is set correctly according to your TV
(page 91).
• Clean the disc with a cleaning cloth.
• If you are using DIGITAL AUDIO OUT (COAXIAL) jack, check the setting in
“Disc Audio” (pages 86-87).
• Clean the disc with a cleaning cloth.
• Clean the disc with a cleaning cloth.
• This unit is not compatible with DTS sound.
• No disc is inserted.
• A blank disc is inserted.
• The disc is upside down. Insert the disc with the labeled side facing up.
• The disc is not correctly inserted.
• The unit cannot play back certain discs (such as a CD-ROM) (page 56).
• The region code on the DVD-video does not match the unit (page 56).
• Moisture has condensed inside the unit. Remove the disc and leave the
unit turned on for about 2 hours until the moisture evaporates (page 3).
• If the disc was recorded on another recorder, the unit cannot play back
the disc if it was not finalized.
• If you are using DVD-RW/-R, please ensure you finalized the disc after
recording (pages 54-55).
• Resume playback was activated (page 62). Press [STOP C] twice.
• You have inserted a disc whose title menu or DVD menu automatically
appears on the TV screen when it is first inserted.
• The DVD-video features an auto playback function.
• Depending on the disc, you may not be able to do some of the
operations. Refer to the instruction manual supplied with the disc.
• The title does not have the multilingual audio tracks.
• The DVD-video prohibits the changing of the language for the sound
track.
• Multilingual subtitle are not recorded on the DVD-video.
• Multi-angles are not recorded on the DVD-video being played back.
• The angle-change operation is whenever possible as long as the disc
contains a multi-angle portion. Actual change will be performed when
the portion has come up.
• The DVD-video prohibits changing angles.
• Try changing the angle using the DVD-video’s menu.
• It may take a few seconds for the unit to input disc data before
recording stops.
Remedy
• It may take a few seconds for the disc tray to open after you have
recorded or edited a disc. This is because the unit is adding disc data to
the disc.
“Repairing” appears on the TV screen.
• If there is a power failure or unplugging during recording, finalizing,
formatting or editing (even after “Repairing” disappears), a repairing
process will begin automatically just after turning the unit on again.
It may take several minutes up to about several hours.
• If you intend to cancel the repairing process, press [A OPEN/CLOSE]
on the front panel, then select “Yes” and press [OK]. After that, press
[OPEN/CLOSE A] to take out the disc. The disc cancelled during the
repairing process MAY NOT work.
DVD
Repairing
In case you intend to cancel the
repairing process.
Basic Setup
Do you want to cancel a repairing
process? When selecting “Yes”,
the disc may not be usable.
Connections
Symptom
The disc tray does not open when you
press [OPEN/CLOSE A].
Introduction
TROUBLESHOOTING
Yes
No
Repairing
Playback
• Head cleaning for VCR may be necessary. Refer to “Auto head cleaning”
(page 4).
• Adjust tracking control for better picture by pressing [CHANNEL / ]
while you are playing back a cassette tape.
The cassette tape does not play back. • No cassette tape is inserted.
Recording does not start after you press • Make sure the cassette tape has an erase-protection tab when you
[REC].
record to a cassette tape. If needed, cover the hole with cellophane
tape.
The remote control does not function. • Check if a cassette tape is in this unit.
The motor rotates even when
• The motor may rotate for the duration of approximately 5 minutes for
playback / recording is stopped.
efficient operation. This is not a malfunction.
Recording
VCR
Picture noise appears.
Editing
Function Setup
VCR Functions
Others
Español
EN
99
TROUBLESHOOTING
Disc Error message
Cause
Solution
Disc Error
— Please eject the disc. —
Playback feature may not be available on
this Disc.
• Unplayable disc is inserted in the unit.
• The disc is upside down.
• Insert the standardized disc which bear
the marks on page 56.
• Insert the disc with the labeled side
facing up.
Region Error
— Please eject the disc. —
Playback is not authorized in your region.
• Playback is not authorized in the region
of the DVD-video which you inserted in
the unit.
• Insert the DVD-video with region codes
1 or ALL.
Parental Lock On
The current selected parental level
prohibits playback.
• The current selected parental level
prohibits playback.
• Check “Parental Lock” setting in
“Playback” menu (page 86).
Recording Error
This program is not allowed to be
recorded.
• The recording function encountered
the copy prohibited program.
• You cannot record copy prohibited
programs.
Recording Error
This program is not recordable in +VR
mode.
• You are trying to record the copy-once
program.
• You cannot record the copy-once
program.
Recording Error
Can not record on this disc.
• You are trying to record onto the disc
which is unrecordable, or the disc status
is unable to record.
• The disc is dirty.
• The disc is damaged.
• Insert the recordable disc, and ensure
the disc status satisfies the recording
requirements (page 39).
• Clean the disc with a cleaning cloth.
• Replace the disc.
Recording Error
This disc is protected and not recordable.
• You are trying to record on to the
protected disc which is set in “Disc Edit”
menu.
• Release the disc protect setting in “Disc
Edit” menu (page 53).
Recording Error
Disc is full.
(No area for new recording)
• You are trying to record onto the disc
which has no space for recording.
• Insert the recordable disc with enough
recording space.
Recording Error
You cannot record more than 49 titles on
one disc.
(The maximum is 49)
• You are trying to record onto the disc
on which the number of recording titles
comes up to the maximum (49).
• Delete unnecessary titles (page 71).
Recording Error
You cannot record more than 254 chapters
on one disc.
(The maximum is 254)
• You are trying to record onto the
DVD+RW or DVD-RW on which the
number of recording chapters comes
up to the maximum (254).
• Delete unnecessary chapter marks
(pages 74-75).
Recording Error
You cannot record on this disc as Power
Calibration Area is full.
• When recordings are performed
repeatedly onto an unstable disc, this
area may come up to be full.
• Every time you insert a disc for
recording, the disc’s working area will
be taken up. And if you repeat this
frequently, it will be used up sooner
and you may not be able to record full
49 titles.
• Insert a new disc.
Recording Error
This disc is already finalized.
• You are trying to record onto the disc
already finalized.
• Release the finalizing for this disc
(page 54).
Recording Error
The disc has no recording compatibility.
Set “Make Recording Compatible” to
“ON” to convert the disc.
• You are trying to record onto the
disc that had been recorded by other
recorders.
• Set “Make Recording Compatible” to
“ON” to rewrite the menu, after that you
will record to disc (page 40).
* If you are still having trouble with the unit after checking “TROUBLESHOOTING”, write down the error code and the
error description for calling our help line mentioned on the front page to locate an Authorized Service Center.
100 EN
Function Setup
VCR Functions
Code
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
Editing
Language
Russian
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish
Sundanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Playback
Others
Code
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
Recording
Language
Hungarian
Icelandic
Indonesian
Interlingua
Interlingue
Inupiak
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean
Kurdish
Laothian
Latin
Latvian; Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Occitan
Oriya
Oromo (Afan)
Panjabi
Pashto; Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Romanian
Basic Setup
Code
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
Connections
Language
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Introduction
LANGUAGE CODE
Español
EN 101
GLOSSARY
Analog Audio
PBC (playback control) (video CD only)
An electrical signal that directly represents sound.
Compare this to digital audio which can be an electrical
signal, but is an indirect representation of sound. See also
“Digital Audio”.
This function enables you to play back interactive
software using a menu screen. See also “Video CD”.
Aspect Ratio
The width of a TV screen relative to its height.
Conventional TVs are 4:3 (in other words, the TV screen
is almost square); widescreen models are 16:9 (the TV
screen is almost twice as wide as it is high).
Chapter (DVD only)
Just as a book is split up into several chapters, a title on a
DVD is usually divided into chapters. See also “Title”.
Component Video Output
Each signal of luminance (Y) and component (PB/CB, PR/
CR) is independent to output so that you can experience
picture color as it is.
Also, due to compatibility with progressive video
(525p/480p), you can experience higher-density picture
than that in interlace (525i/480i).
Digital Audio
An indirect representation of sound by numbers. During
recording, the sound is measured at discrete intervals
(44,100 times a second for CD audio) by an analogto-digital converter, generating a stream of numbers.
On playback, a digital-to-analog converter generates
an analog signal based on these numbers. See also
“Sampling Frequency” and “Analog Audio”.
Dolby Digital
The system to compress digital sound developed by
Dolby Laboratories. It offers you sound of stereo(2ch) or
multi channel audio.
Finalize
To make DVD, which have been recorded on, possible to
play back in DVD players. With this unit, it is possible to
finalize DVD+R, DVD-RW, and DVD-R.
HDMI™ (high definition multimedia interface)
PCM (pulse code modulation)
The most common system of encoding digital audio,
found on CD and DAT. Excellent quality, but requires a
lot of data compared to formats such as Dolby Digital
and MPEG audio. For compatibility with digital audio
recorders (CD, MD and DAT) and AV amplifiers with
digital inputs, this unit can convert Dolby Digital and
MPEG audio to PCM. See also “Digital Audio”.
Progressive Scan (525p/480p)
A type of display that does not split each frame into
fields, and instead scans directly through all the scanlines
of each frame in order. Progressive scan provides less
flickering and higher image resolution than traditional
(525i/480i) TV signals. Refer to page 91 for instructions on
selective progressive scan mode.
Region Code
Regions associate discs and players with particular areas
of the world. This unit will only play back discs that have
compatible region codes. You can find the region code
of your unit by looking on the rear panel. Some discs are
compatible with more than one region (or all regions).
Sampling Frequency
The rate which sound is measured by a specified interval
to turn into digital audio data. The numbers of sampling
in one second defines as sampling frequency. The higher
the rate, the better the sound quality.
SAP (secondary audio program)
Sub-audio channel which is delivered separately from
main-audio channel. This audio channel is used as an
alternate in bilingual broadcasting.
S-Video Output
It delivers independently each signal of color(C) and
luminance(Y) to TV as video signals, so that higher-quality
picture will be gained.
A digital interface between audio and video source. It can
transmit component video, audio, and control signal with
one cable connection.
Title (DVD only)
JPEG (joint photographic experts group)
Audio CD use tracks to divide up the content of a
disc. The DVD equivalent is called a chapter. See also
“Chapter”.
JPEG is a method of compressing still image files. You can
copy JPEG files on CD-RW/-R from a computer and play
back the files on this unit.
MP3 (MPEG audio layer 3)
MP3 is a method of compressing files. You can copy MP3
files on CD-RW/-R from the computer and play back the
files on this unit.
102 EN
A collection of chapters on DVD. See also “Chapter”.
Track
Video CD
A digital format for store video data in compact disc.
+VR (video recording) format
DVD+Rewritable, DVD+Recordable
DVD-Rewritable, DVD-Recordable (+VR mode only)
13.5 MHz
MPEG
Audio recording format
Sampling frequency
Compression format
48 kHz
Dolby Digital
Front
VHF 2~13, UHF 14~69
2~13, A~W, W+1~W+94 (analog W+1~W+84), A-5~A1, 5A
2V rms (input impedance: more than 22kΩ)
1Vp-p (75Ω)
Y: 1Vp-p (75Ω)
C: 286mVp-p (75Ω)
Editing
75Ω unbalanced
2V rms (input impedance: more than 22kΩ)
Function Setup
Rear
Channel frequency synthesized tuning system
Playback
2V rms (output impedance: more than 1kΩ)
1Vp-p (75Ω)
1Vp-p (75Ω)
Y: 1Vp-p (75Ω)
C: 286mVp-p (75Ω)
Y: 1Vp-p (75Ω)
C: 286mVp-p (75Ω)
Y: 1Vp-p (75Ω)
PB/CB: 700mVp-p (75Ω)
PR/CR: 700mVp-p (75Ω)
500mVp-p (75Ω)
VCR Functions
Tuner
Tuning system
Channel coverage (ATSC / NTSC)
Terrestrial
CATV
Terminals
Audio input
RCA jack x 2
Video input
RCA jack x 1
S-video input
Mini DIN 4-pin x 1
VHF/UHF/CATV input and output
F-type
Audio input
RCA jack x 2
Audio output
RCA jack x 4
Video input
RCA jack x 1
Video output
RCA jack x 1
S-video input
Mini DIN 4-pin x 1
S-video output
Mini DIN 4-pin x 1
Component video out
RCA jack x 3
Coaxial digital audio out
RCA jack x 1
HDMI output
HDMI jack x 1
Recording
Video recording format
Sampling frequency
Compression format
Basic Setup
Recording discs
Four heads
120V AC, 60Hz
30W (standby: 3.3W)
17.2 x 4.0 x 10.3 inches (435 x 99.5 x 260mm)
9.5 lbs. ( 4.3kg )
41°F (5°C) to 104°F (40°C)
Less than 80% (no condensation)
ATSC / NTSC-M TV standard
Connections
General
VCR video heads
Power requirements
Power consumption
Dimensions (width x height x depth)
Weight
Operating temperature
Operating humidity
TV system
Recording
Recording format
Introduction
SPECIFICATIONS
Others
Note
• The specifications and design of this product are subject to change without notice.
Español
EN 103
ESPAÑOL
Discos Reproducibles
Disco Grabable
Este aparato es compatible con la reproducción de los
siguientes discos y archivos.
Discos reproducibles
Logotipos
DVD-video
Este aparato puede grabar a DVD+RW, DVD+R, DVD-RW y
DVD-R.
Los discos DVD+R/DVD-R pueden ser grabados sólo una
vez. Los discos DVD+RW/DVD-RW pueden ser grabados y
borrados muchas veces.
En este aparato los discos DVD-RW/-R serán grabados
automáticamente en el modo DVD+VR.
Logotipos
Atributos
DVD+RW
DVD+R
DVD+RW
DVD+R
DVD-RW
DVD-R
DVD-RW
(Sólo discos en modo de video finalizados)
DVD-R
(Sólo discos en modo de video finalizados)
Disco de 8 cm / 12 cm, un solo lado,
una sola capa
Tiempo de grabación máx. aprox.
(modo SLP):
360 minutos (4,7 GB) (para 12 cm)
108 minutos (1,4 GB) (para 8 cm)
• Los siguientes discos se recomiendan para obtener una
buena calidad de grabación y han sido comprobados
como compatibles con este aparato. Sin embargo, según
sea la condición del medio el equipo podría no leer el
disco correctamente.
Verbatim
DVD+R 8x,
DVD+RW 4x,
DVD-R 8x,
DVD-RW 2x
JVC
DVD-RW 4x
Maxell
DVD+R 4x/8x/16x, DVD-R 8x/16x
SONY
DVD+R 4x/8x/16x, DVD+RW 4x
TDK
DVD+R 4x/8x/16x
El comportamiento de cualquier otro disco no está
garantizado.
• Usted puede reproducir discos DVD+RW en la
mayoría de los reproductores de DVD sin finalizarlos.
Sin embargo, si usted ha añadido o eliminado
capítulos, u ocultado capítulos, debe ejecutar
“Compatibilizar edic.” antes de poder ver dichos
efectos en otros equipos. (Consulte la página 81.)
Para reproducir discos que no sean DVD+RW en
otros reproductores de DVD, usted necesitará
finalizarlos.
CD-DA (CD de audio)
CD de video
CD-RW
CD-R
Kodak Picture CD
Disco no Grabable
Archivos reproducibles
Soportes
MP3
CD-RW/-R
JPEG
es una marca registrada de
DVD Format/Logo Licensing Corporation.
Códigos de Región
El número presente en el interior
el globo se refiere a una región
del mundo.Este aparato puede
reproducir discos DVD que estén
rotulados para ALL las regiones o
para la región 1.
104 ES
• Un DVD-RW grabado en un modo distinto de +VR no
será grabable en este aparato a menos que usted borre
todo el contenido del disco. (Consulte la página 80.)
• Un DVD-R grabado en un modo distinto de +VR no será
grabable en este aparato.
Introduction
ESPAÑOL
Conexión Básica
IN --- AUDIO --- OUT
AUDIO IN
L
L
cable RCA de audio
Connections
R
R
VIDEO IN
IN ---VIDEO --- OUT
cable RCA de video
Esta conexión es sólo para
el procesamiento de cada
elemento de la señal de TV
HDMI OUT
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
Y
IN --- AUDIO --- OUT
L
L
R
R
IN
ANTENNA
L
OUT
PB
/CB
IN
COAXIAL
antena de
VHF / UHF
ANT. IN
IN --- VIDEO --- OUT
PR
/CR
R
OUT
cable coaxial
de RF
o
empresa de
TV por cable
IN
ANTENNA
Recording
cable coaxial
de RF
Basic Setup
parte trasera de este aparato
Conexión a un Televisor con un Puerto Compatible con HDMI™
Playback
• HDMI emite las señales de video / audio sin convertirlas en señales analógicas.
• No es necesaria una conexión de audio.
HDMI IN
cable HDMI
HDMI OUT
parte trasera de este aparato
Editing
HDMI OUT
OUT
DIGITAL
AUDIO OUT
AUDIO
OUT
DVD/VCR
S-VIDEO COMPONENT
VIDEO OUT
S-VIDEO
IN --- AUDIO --- OUT
L
Y
L
IN
ANTENNA
L
OUT
PB
/CB
COAXIAL
IN
R
R
IN --- VIDEO --- OUT
R
PR
/CR
ANT. IN
No incline el conector para introducirlo en la toma HDMI y compruebe que el tipo
de toma corresponde con el tipo de conector.
OUT
antena de
VHF / UHF
IN
ANTENNA
cable coaxial
de RF
o
empresa de
TV por cable
Presione [HDMI] para seleccionar el modo de salida HDMI. Cada vez que se presiona [HDMI] el modo de salida varía como sigue.
Pantalla del
panel frontal
Señal de salida
de video
Progresivo de 480
VCR Functions
Modo HDMI y señales efectivas de salida
Function Setup
cable
coaxial
de RF
Esta conexión es sólo
para el procesamiento
de cada elemento de
la señal de TV
Presione [HDMI]
Others
Progresivo de 720
Presione [HDMI]
1080 entrelazado
Presione [HDMI]
Español
Progresivo de 1080
Presione [HDMI]
• El modo HDMI que no esté admitido por el dispositivo de exhibición será pasado por alto.
ES 105
ESPAÑOL
Configuración Inicial
Cuando usted encienda este aparato por primera vez
necesita seguir estos pasos.
1
2
Presione [STANDBY-ON y].
Grabación Básica
1
Encienda el televisor. Seleccione la entrada a
la cual está conectado el aparato.
Utilice [K / L] para seleccionar su
idioma deseado, y luego presione
[OK] para establecerlo.
Presione [DVD].
Presione [OPEN/CLOSE A]
para abrir la bandeja de
discos e insertar su disco
con el rótulo aupntando
hacia arriba. Presione de nuevo
[OPEN/CLOSE A] para cerrar la
bandeja de discos.
* Asegúrese de que el disco sea compatible con este
aparato.(Para obtener la lista de discos compatibles
consulte la página 104.)
Initial Setup
OSD Language
English
Français
Español
2
Para seleccionar un modo de
grabación presione [REC MODE].
HQ (1Hr)
SP (2Hr)
SPP (2.5Hr)
LP (3Hr)
EP (4Hr)
SLP (6Hr)
Elija idioma de preparación.
3
Utilice [K / L] para seleccionar el tipo
de señal de emisión, y luego presione
[OK].
Ajuste inicial
3
Presione [DTV/TV] para seleccionar TV
analógica o TV digital, y a
continuación, utilice [CHANNEL / ]
o [los botones numéricos] y [ • ] (para
canales de TV digital) para seleccionar
un canal que desea grabar.
4
Presione [REC] para iniciar la
grabación.
Ajuste de Canal
Verificar que la antena esté
conectada a la toma "ANTENNA IN".
Antena
Cable (Analógico)
Cable (Analógico/Digital)
Ajuste Auto escaneará los canales terrrestres.
Esto tarda unos momentos en finalizar.
El equipo comenzará a obtener los canales
disponibles en su región.
4
Utilice [{ / B] para seleccionar un
elemento a configurar, y utilice [K / L]
para seleccionar el contenido de su
preferencia, y luego presione [OK].
Calidad del video
Tiempo de
y el sonido
grabación
Disco de 8 cm Disco de 12 cm
18 min
60 min
Buena
36 min
120 min
45 min
150 min
54 min
180 min
72 min
240 min
Deficiente
108 min
360 min
Modo de
grabación
Para configurar la grabación a un toque con
temporizador (OTR)...
Esta es una manera sencilla de configurar el tiempo de grabación en
bloques de 30 minutos.
Presione [REC] repetidamente hasta que aparezca en la pantalla del
televisor la longitud deseada de grabación (30 minutos a 6 horas).
Comenzará la grabación a un toque con temporizador.
I
Ajuste inicial
0h30m
0h30m
Ajste Manual de Reloj
(grabación normal)
ENE / 01 / 2009 ( JUE )
12 : 00 AM
6h00m
OK :
Ajuste hora.
RETURN : Salir de Ajuste inicial.
1h00m
5h30m
Para cambiar la duración de la grabación durante la
grabación a un toque con temporizador:
Presione [REC] repetidamente hasta que aparezca la duración
deseada.
Para cancelar la grabación a un toque con
temporizador dentro del tiempo especificado:
Presione [STOP C].
106 ES
5
Para de tener la grabación presione
[STOP C].
Introduction
ESPAÑOL
Grabación con Temporizador
1
2
Presione [TIMER].
Utilice [K / L] para seleccionar “Prog.
nuevo”, y luego presione [OK].
Programaci. con Reloj
Connections
Usted puede programar el equipo para que grabe hasta 12
programas, con un mes de anticipación. También hay
disponibles grabaciones de programas diarias o semanales.
Antes de grabar, asegúrese de que
• Antes de establecer una programación del temporizador
configure el reloj.
• Inserte un disco grabable con suficiente espacio libre o
una cinta de cassette con una lengüeta de grabación.
JUE ENE/01 11:00AM
Fcha
CH
Configure una programación del
temporizador.
Presione [TIMER SET] para configurar
una programación del temporizador.
Aparecerá
en el pantalla del panel frontal.
Playback
Configure la fecha.
Fcha
ENE/02
CH
DTV69. 1
Empieza
--:-GRAB a
DVD
Recording
Presione [OK].
Basic Setup
3
4
5
Empieza Termina
Prog. nuevo
Termina
--:-Modo
SP
SP
2h00m
Configure las horas de inicio y finalización.
Empieza
12 : 00AM
GRAB a
DVD
Termina
--:-Modo
SP
SP
Editing
Fcha
ENE/02
CH
DTV69. 1
2h00m
ej.) modo digital
Fcha
ENE/02
CH
DTV69. 1
Empieza
12 : 00AM
GRAB a
DVD
Termina
1 : 00AM
Modo
SP
SP
1h00m
Fcha
ENE/02
CH
DTV69. 1
Empieza
12 : 00AM
GRAB a
DVD
Termina
1 : 00AM
Modo
SP
SP
1h00m
Seleccione un modo de grabación.
Fcha
ENE/02
CH
DTV69. 1
Empieza
12 : 00AM
GRAB a
DVD
Termina
1 : 00AM
Modo
SP
SP
VCR Functions
Seleccione un medio de grabación (“DVD” o “VCR”).
Function Setup
Seleccione un modo deseado de entrada y el canal
a grabar.
Para obtener más detalles, consulte “How to select a
channel number for the timer recording” en la página
45 del manual del usuario.
1h00m
la bandeja de
Cerrar la bandeja
Comience a
Detenga la
1 Presione
[DVD].
2 Abra
discos, y Inserte un 3 de discos.
4
reproducir. 5 reproducción.
disco.
Others
Reproducción
Español
ES 107
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship
as follows:
DURATION:
PARTS: FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date
of original retail purchase. Certain parts are excluded from this warranty.
LABOR: FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR OTHER
PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO OBTAIN SERVICE
UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This limited warranty does not apply to any
product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occur during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or products
not supplied by FUNAI CORP., or damage, which results from accident, misuse, abuse, mishandling,
misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or
office use of this product, or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY
COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT
OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO USE THIS
PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL
OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY AN AUTHORIZED SERVICE CENTER.
THIS WARRANTY IS ONLY VALID WHEN THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
THE PRODUCT MUST BE ACCOMPANIED BY A COPY OF THE ORIGINAL RETAIL PURCHASE RECEIPT. IF NO PROOF
OF PURCHASE IS ATTACHED, THE WARRANTY WILL NOT BE HONORED AND REPAIR COSTS WILL BE CHARGED.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION
WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT
PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product freight prepaid, in either its original
packaging or packaging affording an equal degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI
CORP. will not reimburse you for any service done by unauthorized service providers without prior written
approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquiries, please
contact us at:
FUNAI SERVICE CORPORATION
Customer Service
Tel: 1-800-605-8610
www.magnavox.com/support
2200 Spiegel Drive Groveport, OH 43125
Printed in China
E9S80UD
1VMN26713A ★★★★
* 1 V M N 2 6 7 1 3 A *