Philips Speaker 3121 233 43491 User manual

Add to my manuals
4 Pages

advertisement

Philips Speaker 3121 233 43491 User manual | Manualzz
Color TV
Quick Use and Hookup Guide
CONTENTS
IMPORTANT
Important Notice/Warning . . . . . . . . . . . . . . . . . . . . .1
Basic Antenna TV Connections . . . . . . . . . . . . . . . .2
Basic TV Operation . . . . . . . . . . . . . . . . . . . . . . . . . .1
Using the AV1 Inputs . . . . . . . . . . . . . . . . . . . . . . . .3
Remote Battery Installation . . . . . . . . . . . . . . . . . . .1
Using the AV2 Inputs . . . . . . . . . . . . . . . . . . . . . . . .3
Remote Control Button Descriptions . . . . . . . . . . . .1
Using the Component Video Inputs . . . . . . . . . . . . .3
Hooking Up the TV
Using the S-Video Inputs . . . . . . . . . . . . . . . . . . . . .4
Basic Cable TV Connections . . . . . . . . . . . . . . . . . .2
Using the Monitor (Audio/Video) Outputs . . . . . . .4
Basic Cable Box Connections . . . . . . . . . . . . . . . . .2
Using the Side Audio/Video Inputs . . . . . . . . . . . . .4
BASIC TV
AND
NOTE: This owner's manual is used with several
different television models. Not all features (and
drawings) discussed in this manual will necessarily match those found with your television set.
This is normal and does not require that you contact your dealer or request service.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD DO NOT EXPOSE THIS UNIT TO
RAIN OR EXCESSIVE MOISTURE.
REMOTE OPERATION
TELEVISION
Y
our television has a set of controls located on the font of
the cabinet for use when the remote control is not needed.
1
2
Press the POWER button to turn the TV ON.
3
Press the CH – (down) or + (up) button to select TV channels. Use these buttons to make adjustments or selections in
the onscreen menu.
Press the VOL (+) button to increase the sound level or
the VOL (–) button to lower the sound level.
+
Pressing both buttons at the same time will display the
onscreen menu. After you are in the menu, use these buttons
to make adjustments or selections.
T
o load the supplied batteries into the remote:
1
2
3
Reattach the battery compartment door.
CHANNEL
–
Remote Sensor - Sensor for activating
remote control commands when the
remote is used to control the TV.
POWER
1
Power Light Indicator - Light will
show while TV is powered on.
Installing the Remote
Control Batteries
Battery Compartment Door
Remote Control
(shown from the bottom)
Remove the battery compartment door on the back of
the remote.
Place the batteries (2-AA) in the remote. Be sure the (+)
and (–) ends of the batteries line up correctly (the inside of
the case is marked).
+
–
2 3
There is also a set of Audio and Video Input jacks located on
the side of the television cabinet. This jack panel also contains a Svideo and headphone jack. These jacks are great for connecting a
video camcorder or any accessory device that will only be hooked
up temporarily.
REMOTE CONTROL BATTERIES
VOLUME
Be sure to point the
remote at the Remote
Sensor window on the
front of the television
when using the remote
control to operate the
television.
REMOTE CONTROL BUTTONS
Battery Compartment
POWER Button - Press the Power button to turn the TV on or off.
FROWNIE Button - Allows you to delete stored channels within the “Quadra
Surf” lists for the colored buttons.
QUADRA SURF Buttons - (Red, Green, Yellow, Blue) Allows you to
store and surf up to 10 channels you choose for each colored button.
AUTO PICTURE Button - Press repeatedly to choose from 4 different factory
pre-defined picture settings. Choose from Personal (how you set the Picture Menu
adjustment controls), Movies (when watching movies), Sports (for any sporting
event), or Weak Signal (used when the signal being received is not the best).
SMILEY Button - Press to add channels in the “Quadra Surf” lists. Works
with all colored buttons.
TV/VCR/ACC MODE SWITCH - Slide to position of TV to control TV
functions, VCR to control VCR functions and ACC for Cable Converter, DBS,
DVD, etc., functions.
STATUS/EXIT Button - Press to display the current channel number. If the
onscreen menu is displayed, press the Status/Exit button will remove it from the
TV’s screen.
AUTO SOUND Button - Press repeatedly to choose from different factory
pre-defined sound settings. Choose from Personal (how you set the Sound Menu
options), Voice (for programming with speaking only), Music (for musical type
programs such as concerts), or Theatre (used when watching movies).
MENU Button - Press to display the onscreen menu. Also can be used to
back out of the onscreen menu until it disappears from the TV’s screen.
2 “AA” Batteries
CURSOR , , , or Buttons - Press to navigate, select and adjust
controls within the onscreen menu after the Menu button is pressed. These buttons also can be used with a VCR and when the TV/VCR/ACC Switch is in the
VCR position. Press the to PLAY , REWIND , FAST FORWARD ,
or STOP ■ the viewing of a prerecorded video tape. Also use the CURSOR
VOL
VOL(ume) + or – Buttons - Press the VOL + button to increase the TV’s
sound level. Press the VOL – button to decrease the TV’s sound level.
UP or DOWN
to activate or deactivate the EXPAND 4:3 screen
formatting control.
CH(annel) + or – Buttons - Press to select channels in ascending or descending order.
MUTE Button - Press the mute button to eliminate the sound being heard
from the TV. “MUTE” will be displayed on the TV’s screen. Press again to
restore the TV’s volume to it’s previous level.
SLEEP Button - Press the Sleep button to set the TV to automatically turn itself
off after a set period of time. Press repeatedly to select 15, 30, 45, 60, 90, 120, or
180 minutes.
TV/VCR Button - When in the VCR Mode, press to toggle between VCR
viewing and TV viewing. When in the TV mode, this button will have no
functionality.
II PAUSE Button - Press to pause the viewing of a prerecorded video. The picture will freeze on the screen until the Play or Pause buttons are pressed again.
NUMBERED (0-9) Buttons - Press the numbered buttons to select TV channels or to enter certain values within the onscreen menu. For single channel
entries, press the numbered button for the channel you desire. the TV will pause
for a second or two before changing to the chosen channel.
• (VCR Record) Button - Press to start a VCR recording of a TV program.
CC Button - Press to activate the Closed Captioning options. Repeatedly
press the CC button with scroll the options available on the TV screen.
A/CH Button - (Alternate Channel) Press to toggle between the last view
channel and the channel presently being viewed.
3121 233 43491
HOOKING
CABLE/CABLE BOX TV
Y
our Cable TV input into your home may be a single (75 ohm)
cable or use a cable box decoder. In either case the connection is very simple.
Follow the steps below to connect your cable signal to your new
television.
TV
UP THE
Direct Cable Connection:
Cable signal
coming from
Cable Company
(Round 75Ω
coaxial cable)
1
Direct Cable Connections:
b
P
b
P
This connection will supply Stereo sound to the TV.
1
Connect the open end of the round Cable Company supplied cable to the 75Ω input on the TV. Screw it down finger
tight.
Cable Box (w/RF In/Outputs):
Jack Panel Back of TV
Cable Box with RF Inputs and Outputs Connection:
Jack Panel Back
of Cable Box
Output Channel Switch
This connection will NOT supply Stereo sound to the TV. The sound
from the cable box will be mono.
2
3
4
Connect the open end of the round Cable Company supplied cable to the cable signal IN(put) plug on the back of
the Cable Box.
Cable Signal
IN from the
Cable
Company
3
2
OUTPUT
CH
CABLE
IN
Using a separate round coaxial cable, connect one end to the
OUT(put) (TO TV) plug on the back of the Cable Box.
3
TO TV
4
Connect the other end of the round coaxial cable to the
75Ω input on the back of the television. Screw it down finger
tight.
4
Round 75Ω
Coaxial Cable
NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the
back of the cable box to CH 3 or 4, then tune the TV to the corresponding channel. Once tuned, change channels at the cable box, not
the television.
ANT 75‰
Monitor out
AV1 in
AV2 in
VIDEO
Y
L/Mono
AUDIO
Pb
S-VIDEO
R
Pr
COMPONENT VIDEO INPUT
Jack Panel Back of TV
Cable Box (w/Audio/Video Outputs):
This connection will supply Stereo sound to the TV.
5
6
7
Connect the open end of the round Cable Company supplied cable to the cable signal IN(put) plug on the back of
the Cable Box.
Using a RCA type Video Cable, connect one end of the
cable to the Video (or ANT, your cable box may be labeled
differently) Out jack on the cable box and the other end to the
AV1 Video Input on the TV.
Using a RCA type Audio Left and Right Cable, connect one
end to the left and right Audio Out L & R jacks on the
cable box. Connect the other end to the AV1 Audio L & R
Input jacks on the TV.
Cable Box with Audio/Video Outputs Connection:
Cable Signal IN
from the Cable
Company
5
Jack Panel Back
of Cable Box with A/V Outputs
OUTPUT
CH
3
CABLE
IN
24
4
VIDEO
OUT
TO
TV
L
AUDIO
OUT
R
Audio Cables
L & R (Red, White)
Video Cable (Yellow)
6
NOTE: Use the Channel +, or – buttons on the TV remote control to
tune to the AV1 channel for the cable box signal. Once tuned, change
channels at the cable box, not the television.
Monitor out
AV1 in
AV2 in
VIDEO
Y
ANT 75‰
L/Mono
Monitor out
AV2 in
AV1 in
VIDEO
Y
L/Mono
Pb
AUDIO
S-VIDEO
R
Pr
COMPONENT VIDEO INPUT
AUDIO
Pb
R
Pr
S-VIDEO
COMPONENT VIDEO INPUT
ANTENNA TV
combination antenna receives normal broadcast channels (VHF 2–13 and UHF 14–69). Your connection is
easy because there is only one 75Ω (ohm) antenna plug on
the back of your TV, and that’s where the antenna goes.
1
2
Push the round end of the adapter (or antenna) onto the
75Ω (ohm) plug on the back of the TV. If the round end of
the antenna wire is threaded, screw it down finger tight.
7
Antenna Connection:
A
If your antenna has a round cable (75 ohm) on the end,
then you're ready to connect it to the TV.
If your antenna has flat, twin-lead wire (300 ohm), you
first need to attach the antenna wires to the screws on a
300- to 75-ohm adapter.
Jack Panel Back of TV
Outdoor or Indoor Antenna
(Combination VHF/UHF)
The combination antenna receives normal
broadcast channels 2-13 (VHF) and 14-69 (UHF).
1
300 to 75-ohm
Adapter
Twin
Lead Wire
2
ANT 75‰
Monitor out
AV1 in
AV2 in
VIDEO
Y
L/Mono
AUDIO
Pb
S-VIDEO
R
Pr
COMPONENT VIDEO INPUT
Round 75Ω Coaxial
Cable from Antenna
2
Jack Panel Back of TV
HOOKING
UP THE
TV
AV1 & AV2 INPUTS
1
24
T
he TV’s audio/video input jacks are for direct picture and
sound connections between the TV and a VCR (or similar
device) that has audio/video output jacks. Both the AV1 and AV2
Input Jack connections are shown on this page, but either one can
be connected alone. Follow the easy steps below to connect your
accessory device to the AV1 and AV2 in Jacks located on the back of
the TV.
SVHS
Monitor out
3
AV2 in
AV1 in
AV2
BACK
OF TV
VIDEO
Y
L/Mono
CVI
AUDIO
Pb
R
Pr
S-VIDEO
1
2
3
4
5
6
7
Connect the VIDEO (yellow) cable to the VIDEO AV1 in
(or AV2 in) jack on the back of the TV.
AV1
COMPONENT VIDEO INPUT
Connect the AUDIO (red and white) cables to the
AUDIO (left and right) AV1 in (or AV2 in) jacks on the
rear of the TV.
AV1
Connection
Connect the VIDEO (yellow) cable to the VIDEO OUT
jack on the back of the VCR (either one or two) or accessory device being used.
2
2
ANT/CABLE
OUT
S-VIDEO
OUT
R
L
AUDIO OUT
VIDEO
OUT
4
1
BACK OF VCR
Connect the AUDIO (red and white) cables to the
AUDIO (left and right) OUT jacks on the rear of the VCR
(either one or two) or accessory device being used.
Turn the VCR (either one or two) or accessory device
and the TV ON.
Press the CH + or – buttons on the remote control to
select the AV1 channel for accessory device number one, or
the AV2 channel for accessory device number two. AV1 or
AV2 will appear in the upper left corner on the TV screen
depending on the channel chosen.
7
5
6
VOL
With either of the VCRs (or accessory devices) ON and a
prerecorded tape (CD, DVD, etc.) inserted, press the
PLAY button to view the tape on the television.
VCR ONE (or accessory device)
(EQUIPPED WITH VIDEO AND
AUDIO OUTPUT JACKS)
AV2
Connection
AUDIO IN
(RED/WHITE)
c CHECK IT OUT
ANT/CABLE
OUT
Note: The Audio/Video cables needed for this connection are
not supplied with your TV. Please contact your dealer or Philips
at 800-531-0039 for information about purchasing the needed
cables.
VIDEO IN
(YELLOW)
S-VIDEO
OUT
R
L
AUDIO OUT
VIDEO
OUT
3
4
VCR TWO (or accessory device)
(EQUIPPED WITH VIDEO AND
AUDIO OUTPUT JACKS)
5
7
COMPONENT VIDEO INPUTS
C
omponent Video inputs provide for the highest possible color
and picture resolution in the playback of digital signal source
material, such as with DVD players. The color difference signals
(Pb, Pr) and the luminance (Y) signal are connected and received
separately, which allows for improved color bandwidth information (not possible when using composite video or S-Video connections).
1
2
3
4
5
CVI
BACK OF TV
Monitor out
AV2 in
AV1 in
VIDEO
2
Y
L/Mono
1
Connect the Component (Y, Pb, Pr) Video OUT jacks
from the DVD player (or similar device) to the (Y, Pb, Pr)
in(put) jacks on the TV. When using the Component Video
Inputs, it is best not to connect a signal to the AV1 in Video
Jack.
AUDIO
Pb
R
Pr
S-VIDEO
COMPONENT VIDEO INPUT
Connect the red and white AUDIO CABLES to the
Audio (left and right) output jacks on the rear of the accessory device to the Audio (L and R) AV1 in Input Jacks on
the TV.
COMPONENT
VIDEO CABLES
(Green, Blue, Red)
Turn the TV and the DVD (or digital accessory device)
ON.
AUDIO CABLES
(RED/WHITE)
Press the CH +, – buttons to scroll the available channels
until CVI appears in the upper left corner of the TV screen.
COMP VIDEO
Insert a DVD disc into the DVD player and press the
PLAY button on the DVD Player.
VOL
Y
4
VIDEO
AUDIO
R
OUT
HELPFUL HINT
The description for the component video connectors may differ
depending on the DVD player or accessory digital source equipment used (for example, Y, Pb, Pr; Y, B-Y, R-Y; Y, Cr, Cb).
Although abbreviations and terms may vary, the letters b and r
stand for the blue and red color component signal connectors,
and Y indicates the luminance signal. Refer to your DVD or
digital accessory owner’s manual for definitions and connection
details.
S-VIDEO
Pb
Pr
OUT
OUT
L
The CVI connection will be dominate over the AV1 in Video Input.
When a Component Video Device is connected as described, it is best
not to have a video signal connected to the AV1 in Video Input jack.
3
3
5
ACCESSORY DEVICE
EQUIPPED WITH COMPONENT
VIDEO OUTPUTS.
HOOKING
S-VIDEO INPUTS
TV
UP THE
AV2
T
he S(uper)-Video connection on the rear of the TV can provide
you with better picture detail and clarity for the playback of
accessory sources than the normal antenna picture connections.
CVI
2
Monitor out
AV1
1
AV2 in
AV1 in
VIDEO
NOTE: The accessory device must have an S-VIDEO OUT(put)
jack in order for you to complete the connection on this page.
1
2
3
4
5
6
24
Y
L/Mono
Front
Slide the TV/VCR/ACC switch to the VCR position.
Pr
COMPONENT VIDEO INPUT
AUDIO CABLE
(RED/WHITE)
L
R
AUDIO OUT
VIDEO
OUT
2
5
6
3
4
AUDIO CABLES
(Red & White)
Monitor out
AV1 in
1
AV2 in
VIDEO
L
AUX/TV INPUT
PHONO INPUT
Y
L/Mono
AUDIO
Pb
R
Pr
S-VIDEO
COMPONENT VIDEO INPUT
2
AV OUT
AUDIO L(eft) and R(ight)
AUDIO SYSTEM
with AUDIO INPUTS
Second VCR Connection/Recorder
NOTE: Refer to page 9 for the proper hookup of the first VCR.
Follow the instructions on how to tune to the AV 1 channel to
view a pre-recorded tape.
3
The following steps allow you to connect a second VCR to
record the program while your watching it.
3
4
5
Note: The S-Video and Audio
cables needed for this connection
are not supplied with your TV.
Please contact your dealer or Philips
at 800-531-0039 for information
about purchasing the needed cables.
6
VCR
(EQUIPPED WITH
S-VIDEO JACKS)
The S-VIDEO and VIDEO AV2
in(puts) are in parallel. The SVIDEO input is dominant when in
use. If separate video signals are
connected to the S-VIDEO and
VIDEO AV2 in(puts), the signal
from the VIDEO AV2 in(put) will
not be usable.
R
Connect one end of the R(ight) and L(eft) AUDIO
(Monitor Out) jacks on the TV to the R and L audio input
jacks on your amplifier or sound system. Set the audio system’s volume to a normal listening level.
For Second VCR Connection/Recorder:
1
JACK PANEL
Located on the back of the TV
For Audio System Connection:
2
ANT/CABLE
OUT
Audio System Connection
he Monitor (Audio/Video) out jacks are great for recording
with a VCR or used to connect an external audio system for
better sound reproduction.
Turn the TV and audio system ON. You can now adjust
the sound level coming from the audio system with the
VOLUME (+) or (–) button on the TV or remote control.
S-VIDEO
OUT
BACK OF VCR
VOL
T
1
HELPFUL HINT
S-VIDEO
CABLE
Now your ready to place a prerecorded video tape in the
VCR and press the PLAY button.
MONITOR OUTPUTS
R
SVHS
Connect other end of the S-VIDEO CABLE to the SVIDEO OUT jack on the back of the VCR. Then connect
the other ends of the AUDIO (red and white) CABLES to
the AUDIO (left and right) OUT jacks on the rear of the
VCR.
Press the CH + or – buttons on the remote to scroll the
channels until SVHS appears in the upper left corner of the
TV screen.
Pb
S-VIDEO
Connect one end of the S-VIDEO CABLE to the SVIDEO jack on the back of the TV. Then connect one end
the AUDIO (red and white) CABLES to the AV2 in
AUDIO L and R(left and right) jacks on the rear of the TV.
Turn the VCR and the TV ON.
AUDIO
Monitor OUT
VIDEO &AUDIO
L(eft) and R(ight)
JACK PANEL
Located on the back of the TV
VIDEO CABLE
(Yellow)
Connect one end of the yellow Video Cable to the
Monitor out VIDEO plug. Connect the other end to the
VIDEO IN plug on the second VCR.
ANTENNA
IN
OUT
OUT
ANTENNA
OUT
VIDEO
L AUDIO R
IN
IN
Monitor out
AV1 in
AV2 in
OUT
Y
R AUDIO
L/Mono
Connect one end of the red and white Audio cable from
the Monitor out AUDIO L and R plugs on the TV to the
AUDIO IN plugs on the VCR.
OUT
ANTENNA
IN
VIDEO
ANTENNA
OUT
VIDEO
5
AUDIO
Pb
R
Pr
L
IN
S-VIDEO
IN
COMPONENT VIDEO INPUT
Turn the Second VCR ON, insert a black VHS tape and
it’s ready to record what’s being viewed on the TV screen.
AUDIO CABLES
(Red & White)
SECOND VCR
4
FIRST VCR (accessory device)
(Hookup from AV1 on previous page.)
SIDE AUDIO/VIDEO INPUTS
A
udio and Video Side Inputs are available for a quick connection of a VCR, to playback video from a camera or attach a
gaming device. Use the CH + or – buttons on the remote control
to tune these inputs.
1
2
Jack Panel located
on the Side of TV
Front
1
Connect the video (yellow) cable from the Video output
on the Camera (or accessory device) to the Video (yellow)
Input located on the Side of the TV.
S-VIDEO
For Stereo Devices: Connect the audio cable (red and
white) from the Audio Left and Right Outputs on the
Camera to a Stereo to Mono adapter. Then plug the single
end of the adapter to the Audio In (white) jack on the Side
of the television.
AUDIO
L
R
3
Audio Cables
(red & white)
Video Cable
(yellow)
For Mono Devices: Connect one end of the audio cable
from the Audio Out jack on the device to the Audio In
(white) jack on the Side of the television.
3
4
5
2
VIDEO
AUDIO
VIDEO
LEFT RIGHT
Optional
Headphones
Turn the TV and the accessory device ON.
VOL
Press the CH + or – buttons on the remote control to tune
the TV to the side input jacks. “Front” will appear on the
TV screen.
4
Press the PLAY button on the accessory device to
view playback, or to access the accessory device (camera,
gaming unit, etc.).
4
S-VIDEO
Jack Panel
of Accessory Device
5
When headphones re used
the sound coming from the
TV speakers will be mute.
3

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement