Memorex MP3 Player MD6810PLL User manual

MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 19
MD6810PLL
User’s Guide
PERSONAL AM/FM STEREO/COMPACT
DISC PLAYER WITH 45 SECOND DIGITAL
ANTI-SHOCK PROTECTION
Before operating this product,
please read these instructions completely.
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 1
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DANGEROUS VOLTAGE:
The lightning flash with arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
ATTENTION:
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
DANGER:
This product utilizes a Class 1 laser to read Compact Discs.
This laser Compact Disc Player is equipped with safety
switches to avoid exposure when the CD door is open and the
safety interlocks are defeated. Invisible and hazardous laser
radiation when open and interlock failed or defeated. Avoid
direct exposure to beam. Please do not attempt to defeat or
bypass the safety switches.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
SURGE PROTECTORS:
It is recommended to use a surge protector for AC connection.
Lightning and power surges ARE NOT covered under warranty for this
product.
1
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 2
SAFETY PRECAUTIONS (CONTINUED)
INFORMATION:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
•
•
•
•
•
Do not open the CD compartment while the CD is rotating.
Always keep the CD compartment closed when not in use.
Keep all foreign objects out of the CD compartment.
Place the unit on a stable surface.
Avoid installing the unit in locations described below:
• Places exposed to direct sunlight or close to heat radiating
appliances such as electric heaters.
• On top of other stereo equipment that radiates too much
heat.
• Places lacking ventilation or dusty places.
• Places subject to constant vibration.
• Humid or moist places.
2
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 3
Dear Customer:
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of
your musical enjoyment. Now it’s time to consider how you can maximize the fun and
excitement your equipment offers. This manufacturer and the Electronic Industries
Association’s Consumer Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through loud and clear without
annoying blaring or distortion and, most importantly, without affecting your sensitive
hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of
sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise. This list of sound levels is included for your
protection.
Decibel
Level
30
40
50
60
70
80
Example
Quiet library, soft whispers
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock at two feet
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT
EXPOSURE:
We
Want You
LISTENING
For A Lifetime
NI
R
N
EST. 1924
O
O C I A TI
IES
ELECT
U
TR
3
IND
EIA
S
S
Information courtesy of the Deafness Research Foundation.
C
O
S
Subway, motorcycle, truck traffic, lawn mower
Garbage truck, chain saw, pneumatic drill
Rock band concert in front of speakers, thunderclap
Gunshot blast, jet engine
Rocket launching pad
A
90
100
120
140
180
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 4
LOCATION OF CONTROLS
1 2
11
12
3 4 5 6
7
8
13
14
1. DC 4.5V Jack (Side of Unit)
–
10.
+
2. SKIP/SEARCH/Tuning (
)
Button
3. SKIP/SEARCH/Tuning (
)
Button
4. MODE / FM Stereo ON/OFF
Button
5. PRESET ›/‚ Buttons
6. PROG (Program) Button
7. Display
8. ESP/BAND Button
9. PLAY/PAUSE (
9 10
11.
12.
13.
14.
15.
16.
17.
18.
) /POWER
4
15
16 17 18
ON Button
STOP (■)/ POWER OFF
Button
FUNCTION (CD/RADIO)
Switch
Battery Compartment (Inside
CD Compartment)
CD OPEN Switch
CD Compartment
DBBS (Bass Boost) Switch
VOLUME Control
PHONES (Headphones) Jack
LINE OUT Jack (Side of Unit)
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 5
POWER SOURCES
This CD player requires either two (2) “AA” cell batteries (not included) or
the AC adapter (not included).
BATTERY INSTALLATION
The battery indicator (
) will appear in the CD display when the
batteries need replacing.
1. Open the CD Compartment, then open the
– –+
battery compartment door by pressing in on
the tab and then lifting it. To prevent the
possibility of losing the cover, it cannot be
removed.
2. Insert two (2) “AA” cell batteries (not included)
according to the polarity diagram inside the
+ –+
battery compartment. Alkaline batteries are
recommended for the longest playing time.
+
–
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated next to the battery
compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline, Carbon-zinc and rechargeable) or
old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or
injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
(Follow battery manufacturer’s directions.)
AC OPERATION
To operate the unit using AC power, connect the AC adapter (not included) to
an AC outlet having 120V, 60Hz AC only. Plug the small end into the DC
4.5V jack on the side of the unit and connect the other end into the AC outlet.
The batteries are automatically disconnected when the AC adapter is used.
CAUTION: When not using AC power, disconnect the AC adapter from
the wall outlet by pulling the plug (not the cord). Do not touch the AC
adapter with wet hands. Fully insert the plug without exposing any part of
the blade.
DC 4.5V –
+
5
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 6
OPERATION
BASS BOOST
TURNING POWER ON/OFF
1
1
2
To emphasize the bass, slide the
DBBS switch to the ON position. For
normal bass, slide the DBBS switch to
the OFF position.
1
To turn the unit on, press the
PLAY/PAUSE (
)/POWER ON
button ❶.
To turn unit off, Press the STOP (■)
/POWER OFF button ❷.
AUTO POWER OFF
When the unit is stopped (Standby mode) for approximately one minute, the
power will automatically turn off.
Sound Through a Home Audio System
By using a home audio connection cable (not included), superb sound can
be heard through your home audio system. Before making any connections,
turn off the power to all equipment.
Plug a connection cable (not included) between the LINE OUT jack on the
side of the CD player and the amplifier’s AUX or CD input jack. (Do not
connect it to the amplifier’s PHONO jack.)
NOTE: If the radio interferes with TV reception, move the unit away from the
TV or turn off the power to this unit.
6
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 7
RADIO OPERATION
TO LISTEN TO THE RADIO
1
2
2
1
2
3
1
Set the VOLUME control ❶ to minimum
and plug the headphone into the
PHONES jack. Press the PLAY/PAUSE
) /POWER ON button ❷ to turn the
(
unit on.
Slide the FUNCTION switch ❶ to the
RADIO position. Press the ESP/BAND
button ❷ to select a band (AM or FM).
If listening to FM, press the MODE button
❸ to turn FM Stereo ON or OFF.
3
4
1
3
2
2
1
Press and release the SKIP/SEARCH/
Tuning
❶ or
button ❷ to tune
a station. Press and hold the
SKIP/SEARCH/Tuning
❶ or
button ❷ for Auto Scan (see below).
Adjust the VOLUME control ❶ and DBBS
switch ❷ as desired. If FM STEREO
reception is weak/noisy, press the MODE
button ❸ to turn off Stereo; in this case
the reception will be monaural.
5
ANTENNAS
AM – This unit has a built-in ferrite bar
antenna, which provides adequate reception
in most areas. If reception is weak, turn the
unit to improve reception.
FM – The headphones act as an antenna for
FM. Extend the headphone wire for best FM
reception.
To turn the radio off, press the STOP
(■)/POWER OFF button.
AUTO SCAN
Press and hold the SKIP/SEARCH/Tuning
or
button for approximately one
second and the unit will automatically search
for the next available station.
7
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 8
RADIO OPERATION (CONTINUED)
TO SET AND RECEIVE A STATION INTO MEMORY
You can set up to 10 AM and 10 FM stations into memory as follows:
2
1
3
2
1
Tune a desired station as described in
the previous section. Press the PROG
button; the PROG indicator will blink
and the preset number will appear in
the display.
3
1
While the PROG indicator is blinking,
select the desired preset using the
PRESET › ❶ or ‚ ❷ button, then
press the PROG button ❸ to set the
memory.
2
To recall a preset station, simply
press the PRESET › ❶ or ‚ ❷
button to select the desired preset.
8
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 9
CD OPERATION
TO PLAY A CD (Standard, CD-R and CD-RW)
2
1
2
1
Open the CD compartment lid by
sliding the CD OPEN switch ❶ to the
right. Gently press a disc, label side
up, onto the spindle until it locks in
place. Close the CD compartment lid.
Insert headphones into the PHONES
jack. Slide the FUNCTION switch ❷ to
the CD position.
While the unit is off, press the
PLAY/PAUSE (
)/POWER ON
button to start playback. To pause
PLAYBACK, press the PLAY/PAUSE
(
)/POWER ON button again, the
time display will blink. Press once
again to resume playback.
3
4
3
4
2
1
When the disc is through playing, it will
stop. Press the STOP (■)/POWER
OFF button to stop the disc before it is
finished; the total number of tracks will
appear. Press the STOP (■)/POWER
OFF button again while in the stop
mode to turn the unit off or wait
approximately 60 seconds and the unit
will automatically turn off.
Adjust the VOLUME control ❶ and
DBBS switch ❷ as desired. To skip
forward or backward through the tracks
on the disc, press the SKIP/SEARCH
❸ or
button ❹. To search
forward or backward through the tracks
on the disc, press and hold the
SKIP/SEARCH
❸ or
button ❹.
9
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 10
CD OPERATION (CONTINUED)
NOTES:
• This unit is capable of playing standard CDs or 3” singles; no adapter is required.
• If a disc is inserted incorrectly, dirty, damaged or not present at all, the display will
show “no disc”.
• As each track is played, the track number and elapsed time are shown in the display.
• To remove the disc, open the CD Compartment, hold the edge of the CD and gently
press the center pivot and lift the CD.
• The maximum time of a CD is 74 minutes for this unit.
• “OPEN” will appear in the display when the CD Door is opened.
ANTI-SHOCK SYSTEM
This CD player has a built-in Anti-Shock System that minimizes CD skipping,
which is useful when using the CD player in the car. Follow the steps below to
activate and understand the Anti-Shock System.
2
1
2
1
Open the CD compartment lid by sliding
the CD OPEN switch ❶ to the right. Gently
press a disc, label side up, onto the spindle
until it locks in place. Close the CD
compartment lid. Insert headphones into
the PHONES jack. Slide the FUNCTION
switch ❷ to the CD position.
With a CD inserted, press the
PLAY/PAUSE (
)/POWER ON
button to turn the unit on.
3
4
The Anti-Shock System will start
automatically, the sound will mute for a
moment and the display will show the
Anti-Shock indicator with no bars in it.
Within a few seconds, the Anti-Shock
indicator will fill to indicate music
signals are stored in memory.
CONTINUED ON THE NEXT PAGE
10
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 11
CD OPERATION (CONTINUED)
5
6
If the CD player is subject to vibration
during playback, the bars will
disappear one by one. During the
vibration, the music should continue to
play the signals stored in the memory
until the CD player can read the music
data properly from the disc. At this
time, the indicator will probably show
fewer bars indicating the music signals
stored in memory are low.
If all the bars disappear and the CD
player is subject to immediate vibration,
the unit may skip.
7
8
If no more vibration occurs, the
music signals are once again stored
into the memory and the indicator
returns to full. When the memory is
full, the top bar will blink and the
disc rotation speed will drop to save
power consumption.
To turn the Anti-Shock System off,
press the ESP/BAND button.
To turn the Anti-Shock System on,
press the ESP/BAND button again.
NOTES:
• When the CD player is used in a stable location, turn the Anti-Shock System
off by pressing the ESP/BAND button. When the Anti-Shock System is Off,
battery consumption is less.
• The Anti-Shock System provides for continuous sound output when unit is
subject to vibration, but it will not correct errors, such as a defective or dirty
CD.
11
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 12
CD OPERATION (CONTINUED)
TO REPEATEDLY PLAY BACK ONE TRACK
1
4
3
2
2
1
1
3
With a CD inserted, press the
PLAY/PAUSE (
)/POWER ON
button ❶ to turn the unit on, then
select a track using the SKIP/SEARCH
❷ or
button ❸ . Press the
MODE button ❹ once; the Repeat 1
indicator
will appear in the display.
2
The unit will then play the same track
over and over until the STOP
(■)/POWER OFF button ❶ is pressed.
Adjust the VOLUME control ❷ and
DBBS switch ❸ as desired.
TO REPEATEDLY PLAY BACK ALL TRACKS
1
2
2
1
1
3
With a CD inserted, press the
PLAY/PAUSE (
)/POWER ON
button ❶ to turn the unit on. Press the
MODE button ❷ twice; the Repeat All
ALL will appear in the
indicator
display.
2
The unit will then play all the tracks on
the CD over and over until the STOP
(■)/POWER OFF button ❶ is pressed.
Adjust the VOLUME control ❷ and
DBBS switch ❸ as desired.
TO CANCEL OR STOP REPEAT PLAYBACK
• TO STOP REPEAT PLAYBACK, press the STOP (■)/POWER OFF button once.
• TO CANCEL REPEAT PLAYBACK, press the MODE button four times if in
Repeat 1 mode, or three times if in Repeat all mode. The unit will continue
normal playback.
12
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 13
CD OPERATION (CONTINUED)
INTRO PLAY
1
2
3
2
1
1
4
2
3
With a CD inserted, press the
PLAY/PAUSE (
)/POWER ON
button ❶ to turn the unit on and press
the STOP (■)/POWER OFF button ❷
to stop auto playback. Press the MODE
button ❸ three times; the INTRO
indicator will blink in the display.
Press the PLAY/PAUSE (
)/POWER
ON button ❶ to begin playback. The unit
will play the first 10 seconds of each
track. Adjust the VOLUME control ❷
and DBBS switch ❸ as desired. Press
the STOP (■)/POWER OFF button ❹
to stop Intro playback.
TO RANDOMLY PLAY BACK A CD
1
2
3
2
1
1
4
3
With a CD inserted, press the
PLAY/PAUSE (
)/POWER ON
button ❶ to turn the unit on and press
the STOP (■)/POWER OFF button ❷
to stop auto playback. Press the
MODE button ❸ four times; the RAND
indicator will blink in the display.
2
Press the PLAY/PAUSE (
)/POWER
ON button ❶ to begin playback. The
unit will play all the tracks in random
order. Adjust the VOLUME control ❷
and DBBS switch ❸ as desired. When
all the tracks have been played, the
unit will stop. Press the STOP
(■ )/POWER OFF button ❹ to stop
Random playback.
13
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 14
CD OPERATION (CONTINUED)
TO PROGRAM THE MEMORY (UP TO 24 TRACKS)
1
2
3
1
2
3
2 1
With a CD inserted, press the
PLAY/PAUSE (
)/POWER ON
button ❶ to turn the unit on and press
the STOP (■)/POWER OFF button ❷ to
stop auto playback. Press the PROG
button ❸ ; the PROG indicator will
appear in the CD display.
Select the first track to be played back
using the SKIP/SEARCH
❶ or
button ❷, then press the PROG button
❸ again. Repeat this step to program
additional tracks up to a maximum of
24 tracks.
3
4
1
3
1
2
2
Press the PLAY/PAUSE (
)
/POWER ON button ❶ to begin
programmed playback and adjust the
VOLUME control ❷ and DBBS switch
❸ as desired.
To skip forward or backward through
the
programs,
press
the
SKIP/SEARCH
❶ or
button
❷. When the disc is through playing, it
will stop.
NOTES:
• Press the STOP (■)/POWER OFF button to stop the disc before it is finished.
• As each program is played, the track number is shown in the display.
• To clear the memorized program either 1)press the STOP (■)/POWER OFF
button again while in the stop mode, wait approximately 60 seconds and the unit
will turn off or 2) open the CD compartment.
• Programming is the ability to preselect the order in which a series of tracks
will be played.
• Each track may be stored in the program memory as many times as desired
(up to 24 tracks).
14
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 15
CARE AND MAINTENANCE
Caring for Compact Discs
• Treat the compact disc carefully. Handle the
compact disc only by its edges. Never allow your
fingers to come in contact with the shiny,
unprinted side of the compact disc.
• Do not attach adhesive tape, stickers, etc. to
the compact disc label.
• Clean the compact disc periodically with a soft, lint-free, dry cloth. Never use
detergents or abrasive cleaners to clean the compact disc. If necessary, use a
CD cleaning kit.
• If a compact disc skips or gets stuck on a section of the disc, it is probably dirty
or damaged (scratched).
B ENZEN E
C LE A N E R
• When cleaning the compact disc, wipe in straight lines from the
center of the compact disc to the outer edge of the compact disc.
Never wipe in circular motions.
• This unit is designed to play only compact discs bearing the identification logo
as shown here. Other compact discs may not conform to the CD standard and
may not play properly.
• Compact discs should be stored in their cases after each use to avoid
damage.
• Do not expose compact discs to direct sunlight, high humidity, high
temperatures, or dust, etc. Prolonged exposure or extreme temperatures can
warp the compact disc.
• Do not stick or write anything on either side of the compact disc. Sharp writing
instruments, or the ink may damage the surface.
Cleaning the unit
• To prevent fire or shock hazard, disconnect your unit from the AC power
source when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other
furniture. Use caution when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
15
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 16
TROUBLESHOOTING GUIDE
If you experience a problem with this unit, check the chart below before
calling for service.
SYMPTOM
Unit will not
turn on.
Disc will not play.
Erratic CD playback.
No sound from
headphones.
ESP not working.
Noise or sound
distorted on radio.
FM STEREO indicator
does not light.
No sound.
CAUSE
Weak or dead batteries
or inserted incorrectly.
Weak or dead Rechargeable batteries.
AC adapter
not connected.
CD compartment
not closed.
Disc inserted
incorrectly.
Dirty or defective
disc.
Moisture
condensation
on disc.
Dirty or defective
disc.
Headphone
plug not inserted
correctly.
VOLUME control
set to minimum.
Weak batteries.
Defective disc.
ESP is not activated.
Station not tuned
properly for AM or FM.
FM: Headphone wire
not extended.
AM: Unit is not
positioned correctly.
Poor FM signal.
MODE button
not set to Stereo.
FUNCTION switch is not
in the desired position.
16
SOLUTION
Replace batteries and insert
correctly.
Recharge or replace
batteries (if used).
Check AC adapter
connection.
Close CD compartment.
Reinsert disc correctly.
Try another disc.
Wipe disc with soft
cloth.
Clean or replace disc.
Reinsert headphone
plug correctly.
Increase volume.
Replace batteries.
Try another disc.
Press the ESP/BAND button.
Retune AM or FM
broadcast station.
Extend Headphone wire.
Rotate unit until best
reception is obtained.
Retune station.
Press MODE button to turn
Stereo on.
Set FUNCTION switch to the
desired function.
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 17
SPECIFICATIONS
Power requirements......................................2 x LR6 "AA" alkaline battery
DC in 4.5V adaptor (center positive)
Frequency Range (FM) ................................................... 87.5 ~ 108 MHz
Frequency Range (AM) ....................................................530 ~ 1720 KHz
D/A conversion ...................................1-bit DAC eight times oversampling
Frequency response ............................................20~20,000Hz (+1,-3 dB)
Anti-shock. .......................................................................45 second buffer
Output level. ..........................................Line output: 0.6 Vms (47K ohms)
Headphone: 16mW (32 ohms)
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE
VISIT OUR WEBSITE AT
WWW.MEMOREXELECTRONICS.COM
OR CONTACT CUSTOMER SERVICE AT 1-800-919-3647.
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90
DAYS IN CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR
PLACE OF PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT
1-800-321-6993.
17
MD6810.PLL.O/M.QXD
6/11/03
2:58 PM
Page 18
Memcorp, Inc.
Weston, FL
Printed in Hong Kong
Visit our website at www.memorexelectronics.com