advertisement
▼
Scroll to page 2
of 4
C2228M-C (7/07) PMCL-V200 Monitor Mount Adapter Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Installation should be done only by qualified personnel and conform to all local codes. 6. Use only installation methods and materials capable of supporting four times the maximum specified load. 7. Only use replacement parts recommended by Pelco. 8. This unit is designed for indoor use only, and it must not be installed where exposed to rain or moisture. Description The PMCL-V200 monitor mount adapter allows an LCD monitor mount to be used with larger LCD monitors, such as Pelco’s 500 Series monitors. This adapter accommodates monitors with 200 x 200 mm and 200 x 100 mm hole patterns. The PMCL-V200 monitor mount adapter can be used with the following Pelco mounts: PMCL-WM Wall mount PMCL-WMT Tilt-swivel wall mount PMCL-WM1A Single-arm wall mount PMCL-WM2A Double-arm wall mount PMCL-CM Ceiling mount PMCL-CMP Ceiling mount and telescoping pole Installation The following parts are supplied: Qty 1 4 4 4 4 4 4 4 Description Adapter plate 10-32 x 3/4-inch flat head Phillips screws, stainless steel #10 split lock washers 10-32 hex nuts, stainless steel M6 x 12 mm pan head Phillips screws, stainless steel #8 split lock washers M4 x 10 mm pan head Phillips screws, stainless steel Flat washers C2228M-C (7/07) 1 To attach the PMCL-V200 to a monitor mount: 1. Use the 10-32 x 3/4-inch flat head Phillips screws, #10 split lock washers, and hex nuts (supplied) to secure the adapter plate to the monitor mount. Refer to Figure 1. ADAPTER PLATE PMCL-WM1A MONITOR MOUNT HEX NUT #10 SPLIT LOCK WASHER 10-32X3/4 PHILLIPS SCREW Figure 1. Attaching the PMCL-V200 Monitor Mount Adapter to a Monitor Mount 2. Attach the monitor mount to the monitor. Refer to Figure 2 and do one of the following: • 31-inch monitor or smaller: Align the monitor to the correct hole pattern on the mounting plate. Use the M4 x 10 mm screws and split lock washers (supplied) to secure the monitor to the mounting plate. or • Monitors larger than 31-inches: Align the monitor to the outside hole pattern of the monitor plate. Use the M6 x 12 mm screws and flat washers (supplied) to secure the monitor to the mounting plate. PMCL-WM1A MONITOR MOUNT #8 SPLIT LOCK WASHER PMCL-V200 ADAPTER PLATE M4X10MM PHILLIPS SCREW Figure 2. Attaching the PMCL-V200 Adapter and Monitor Mount to a Monitor 3. Refer to the manual shipped with the monitor mount for further instructions. 2 C2228M-C (7/07) PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3000 Series unshielded twisted pair transmission products. • Three years on Spectra ® IV products. • Three years on Genex ® Series products (multiplexers, server, and keyboard). • Three years on Camclosure ® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models, which have a five-year warranty. • Three years on PMCL200/300/400 Series LCD monitors. • Two years on standard motorized or fixed focal length lenses. • Two years on Legacy ®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products. • Two years on Spectra III ™, Esprit®, ExSite®, and PS20 scanners, including when used in continuous motion applications. • Two years on Esprit and WW5700 Series window wiper (excluding wiper blades). • Two years (except lamp and color wheel) on Digital Light Processing (DLP ®) displays. The lamp and color wheel will be covered for a period of 90 days. The air filter is not covered under warranty. • Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura ™ Series distributed network-based video products. • One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months. • Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes). Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty. Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise. The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state to state. If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: 1. Model and serial number 2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number 3. Details of the defect or problem If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written explanation with the product when returned. Method of return shipment shall be the same or equal to the method by which the item was received by Pelco. RETURNS In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair). All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge. Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate address below. If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to: Service Department Pelco 3500 Pelco Way Clovis, CA 93612-5699 If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the following: If the goods are to be sent by a COURIER SERVICE, send the goods to: Pelco 3500 Pelco Way Clovis, CA 93612-5699 USA If the goods are to be sent by a FREIGHT FORWARDER, send the goods to: Pelco c/o Expeditors 473 Eccles Avenue South San Francisco, CA 94080 USA Phone: 650-737-1700 Fax: 650-737-0933 The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC. REVISION HISTORY Manual # C2228M C2228M-A C2228M-B C2228M-C Date 8/06 10/06 12/06 7/07 Comments Original version. Updated supplied hardware per ECO 06-16922. Added hardware information for large monitors per ECO 06-17078. Added flat washers to Figure 1, and revised the screw size and split lock washers in the parts list and Figure 2. Pelco, the Pelco logo, Camclosure, Esprit, ExSite, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and Spectra III are trademarks of Pelco. DLP is a registered trademark of Texas Instruments, Inc. © Copyright 2007, Pelco. All rights reserved. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore | Spain | Sweden | United Arab Emirates | United Kingdom | United States South Africa
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project