Samsung Network Card SADT-103WM User manual

Samsung Network Card SADT-103WM User manual
SADT - 103WM
Wall Mount Adaptor
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
www.samsung.com/global/register
SADT-103WM_ENG.indd 1
2008-03-18 오전 9:13:51
Overview
The Wall Mount Adapter is used to install the OUTDOOR
HOUSING (SHG-221/222) on the indoor/outside wall.
ENG
Notice
• Make sure that you must select an installation spot to endure the total weight of "Wall
Mount Adapter", "Outdoor Housing" and "Smart Dome Camera".
• This product is designed to use with anchor bolts and anchor nuts (M10).
• If installing in a concrete wall, use a M10 anchor bolt (nut) with flat washer and spring
washer.
• Each installed anchor bolt should endure 700kg of pulling force.
• Wall Mount Adapter can be installed directly in the wall, and also attached to CORNER
MOUNT ADAPTOR(SADT-110CM), or POLE MOUNT ADAPTOR(SADT-100PM). At this
time, please use the PG-13.5 cable grand.
Installation
1. Select an installation spot which can endure more than 4 times of the product weight.
2. Refer to the following wring diagram to prepare cables necessary for connecting the
Outdoor Housing.
SADT-103WM_
SADT-103WM_ENG.indd 1
2008-03-18 오전 9:13:51
The wiring diagram to connect the outdoor cable of the OUTDOOR HOUSING(SHG-221/222)
3. If you mount the Wall Mount Adaptor on the wall, mark a hole where you insert the anchor
bolt or anchor nut (M10) using the Cover Plate, and drill a hole for the anchor bolt (nut).
If you install it in a corner of the wall, use the Corner Mount Adaptor (SADT-110CM).
If installing on the pole of the wall, use the Pole Mount Adaptor (SADT-100PM) for this
purpose.
150 mm
COVER PLATE
The hole for joining
a ANCHOR BOLT
80 mm
_SADT-103WM
SADT-103WM_ENG.indd 2
2008-03-18 오전 9:13:52
4. Prepare the Holder Housing from the Outdoor Housing and insert the cables of the Holder
Housing into the Wall Mount Adaptor before pulling them out through the hole of the
Cover Fixing Part.
ENG
WALL MOUNT ADAPTOR
WALL MOUNT ADAPTOR
The place for
joining a COVER
CABLE
HOLDER HOUSING
HOLDER HOUSING
5. Fit the Guide of the Holder Housing into the corresponding Guide Hole of the Wall Mount
Adaptor while inserting the Holder Housing into the Wall Mount Adaptor.
- Install the Holder Housing so that the “FRONT” label faces the front of the camera.
- Make sure that the Bush Cable should not be loose from the Holder Housing.
(If the Bush Cable is not secured firmly, the product is not properly waterproof.)
WALL MOUNT ADAPTOR
BUSH CABLE
GUIDE HOLE
GUIDE
HOLDER HOUSING
SADT-103WM_
SADT-103WM_ENG.indd 3
2008-03-18 오전 9:13:53
6. Turn the Holder Housing clockwise by 18 degrees. Then, use 3 screws(M4×L8,
suported), to fix the Holder Housing to the Wall Mount Adaptor.
WALL MOUNT ADAPTOR
WALL MOUNT ADAPTOR
SCREW
HOLDER
HOUSING
HOLDER HOUSING
Turn to the clockwise
about 18 degrees
7. According to the status of connected cable of the OUTDOOR HOUSING, SHG-221/222),
a way of installation is different as follows.
 If the cable pipe is installed inside of the wall
 Use the Cable Grand to connect the external cables with the Cover Plate.
- You should use only the Grand Cable for waterproof purpose. Furthermore, it is
recommended to keep the cable about 150mm longer than the Cover Plate.
150 mm
COVER PLATE
CABLE GRAND
_SADT-103WM
SADT-103WM_ENG.indd 4
2008-03-18 오전 9:13:54
 If you use only the Grand Cable to fix the cables to the Cover Plate, the other hole of
the Cover Plate should be sealed up with the Rubber Cap for waterproofness.
COVER PLATE
ENG
150 mm
CABLE GRAND
RUBBER CAP
 The different cables on the Cover Plate can be pulled out through the hole of the Cover
Fixing Part of the Wall Mount Adaptor. 4) Then, use 6 screws (Flat, M3xL8) to fix the
Cover Plate to the Wall Mount Adaptor.
- Make sure that the Gasket part should keep contact with the Wall Mount Adaptor
during the fixation.
The place for joining a COVER
WALL MOUNT ADAPTOR
GASKET
COVER PLATE
SCREW
SADT-103WM_
SADT-103WM_ENG.indd 5
2008-03-18 오전 9:13:55
 If the cable pipe is installed outside of the wall
 Drill a 21mm-diameter hole on the Wall Mount Adaptor (side and top, respectively).
For your reference, see the figure below.
- The drilling process for the Wall Mount Adaptor must be performed prior to the
fixing process of the Holder Housing according to the steps 4, 5, 6 in this installation
guide.
* Drilling Points (unit: mm)
(a) Top
(b) Side
 Put two Rubber Caps upon the Cover Plate.
- Make sure you do this as it is necessary for waterproofing.
COVER PLATE
RUBBER CAP
_SADT-103WM
SADT-103WM_ENG.indd 6
2008-03-18 오전 9:13:56
 Use the Grand Cable to fix the necessary cables to the Wall Mount Adaptor before
pulling them out of the hole of the Cover Fixing Part.
The place for
joining a COVER
ENG
WALL MOUNT ADAPTOR
CABLE GRAND
 Use 6 screws (Flat, M3xL8) to fix the Cover Plate to the Wall Mount Adaptor.
- Make sure that the Gasket part should keep contact with the Wall Mount Adaptor
during the fixation.
GASKET
COVER PLATE
SCREW
WALL MOUNT ADAPTOR
8. Use the anchor bolt and nut to secure the Wall Mount Adaptor to the wall.
WALL MOUNT ADAPTOR
ANCHOR BOLT
SADT-103WM_
SADT-103WM_ENG.indd 7
2008-03-18 오전 9:13:57
9. See the wiring diagram below for connecting the cables of the Camera Adaptor.
A. Remove one of the Connectors connected to the cable end of the Camera Adaptor.
B. Peel off the coating on the cable end of the Connector and connect it to the external
cable using soldering.
(See the cable wiring diagram in the installation guide of the Camera for connecting the
cables.)
C. Use an insulation tape to wrap up the soldering portion of two cables.
D. Connect the Connector to the Camera Adaptor again.
E. Repeat the above 4 steps to connect all of the 4 Connectors to the corresponding
external cables.
F. In the last step, connect the BNC jack.
CAMERA ADAPTOR
CAMERA ADAPTOR
CABLE
CONNECTOR
External Cable
Soldering
BNC JACK
CONNECTOR
_SADT-103WM
SADT-103WM_ENG.indd 8
2008-03-18 오전 9:13:59
10. Insert the joined cable into the Wall Mount Adaptor through the Cover Fixing Part.
Insert one piece of the two-strand cable into an empty area of the Wall Mount Adaptor
as in the figure below and push the other one into the Wall Mount Adaptor.
(Ensure that the insulated coating of the cable should be kept intact while the insertion)
ENG
the place for joining a cover
WALL MOUNT ADAPTOR
< Insert one piece of the two-stranded cable >
WALL MOUNT ADAPTOR
< Insert the other piece of the two-stranded cable >
11. Use 2 screws (M3xL4, suported) to fix the Cover to the Wall Mount Adaptor.
WALL MOUNT ADAPTOR
COVER
SCREW
SADT-103WM_
SADT-103WM_ENG.indd 9
2008-03-18 오전 9:14:01
12. Now you can couple the Outdoor Housing with the Holder Housing and do the same
with the Cover Front and the Cover Rear.
(For more information, see the installation guide for the Outdoor Housing (SHG-221/
SHG-222).)
WALL MOUNT ADAPTOR
COVER FRONT
COVER REAR
OUTDOOR HOUSING
13. For waterproofness, apply the silicon sealant between and around the Wall and the
Wall Mount Adaptor when the installation is done. If the adaptor is installed in an irregular
(uneven) surface, make sure to seal up all the possible gaps.
10_SADT-103WM
SADT-103WM_ENG.indd 10
2008-03-18 오전 9:14:01
Product Specification
ENG
Location for use: Indoors or outdoors
Installation Spot: Wall or Vertical Structure
Dimension: See the figure
Weight: 1,250g
Material: aluminium
Operation Temperature: -40˚C ~ 50˚C
HUMIDITY: 0~100%
3
2R3
4-
ί10
,5
4-Ø
Œ10,
5
Accessories
Cover Plate ...................................... 1 (Gasket Attached)
Cover ............................................... 1
Screw (flat, M3xL8) ........................... 6 (For fixing Wall Mount + Cover Plate)
Screw (M3xL4) ................................. 2 (For fixing Wall Mount + Cover)
Screw (M4xL8) ................................. 3 (For fixing Wall Mount + Holder Housing)
Rubber Cap ..................................... 2
MANUAL ......................................... 1
SADT-103WM_11
SADT-103WM_ENG.indd 11
2008-03-18 오전 9:14:02
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other
household wastes at the end of its working life. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
SADT-103WM_ENG.indd 12
2008-03-18 오전 9:14:02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement