Panasonic | TV VCR Combo PVQ-1312B | User manual | Panasonic TV VCR Combo PVQ-1312B User manual

Panasonic TV VCR Combo PVQ-1312B User manual
Initial Setup
Combination VCR
Operating Instructions
Models No. PVQ-1312W
Basic Operation
/ PVQ-1312B
PVQ-2012 / PVQ-2512
TV Operation
As an ENERGY STAR® Partner,
Matsushita Electric Corporation of America has
determined that this product or product model meets
the ENERGY STAR® guidelines for energy efficiency.
LSQT0605A
Please read these instructions carefully before attempting to connect,
operate, or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Timer Operation Advanced Operation For Your Information
• Initial Setup and Connection Procedures are on pages 8 and 9.
Important Safeguards and Precautions
READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS INTHE MANUAL AND ON UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from power source indicated on unit
or in this manual. If uncertain, have your Electric
Utility Service Company or Video Products Dealer
verify your home power source.
2 POWER CORD PLUG
For safety, this unit has a polarized type plug (one
wide blade), or a three-wire grounding type plug.
Always hold the plug firmly and make sure your
hands are dry when plugging in or unplugging the
AC power cord. Regularly remove dust, dirt, etc.
on the plug.
POLARIZED PLUG CAUTION:
The plug fits into outlet one way. If it cannot be fully
inserted, try reversing it. If it still will not fit, have an
electrician install the proper wall outlet. Do not
tamper with the plug.
GROUNDING PLUG CAUTION:
The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper
outlet. Do not tamper with the plug.
3 POWER CORD
To avoid unit malfunction, and to protect against
electrical shock, fire or personal injury:
-Keep power cord away from heating appliances
and walking traffic. Do not rest heavy objects on,
or roll such objects over the power cord.
-Do not tamper with the cord in any way.
-An extension cord should have the same type
plug (polarized or grounding) and must be
securely connected.
-Overloaded wall outlets or extension cords is a
fire hazard.
-Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and
should be replaced by a qualified electrician.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a fire hazard or heat
damage to cassettes.
For your protection:
a. Never cover ventilation slots while unit is ON,
or operate unit while placed on a bed, sofa,
rug, or other soft surface.
b. Avoid built-in installation, such as a book case
or rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place unit over or near a heater or
regulator, in direct sunlight, etc. If unit is suddenly
moved from a cold place to a warm place,
moisture may condense in unit and on the tape
causing damage.
6 TO AVOID PERSONAL INJURY
• Never place unit on support or
stand that is not firm, level,
and adequately strong.
The unit could fall causing
serious injury to a child or
adult and damage to the unit.
• Move any appliance and cart
combination with care. Quick
stops, excessive force, and uneven
surfaces may cause objects to overturn.
• Carefully follow all operating instructions.
2
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
An outside antenna or cable system must be properly
grounded to provide some protection
against built up static charges
and voltage. Section 810 of
the National Electrical Code,
ANSI/NFPA 70 (in Canada,
part 1 of the Canadian
Electrical Code) provides
information regarding proper
grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements for
the grounding electrode.
NEC - NATIONAL
ELECTRICAL CODE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA LEAD
IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE
GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE
POWER LINES OR CIRCUITS
Locate an outside antenna system well away from power
lines and electric light or power circuits so it will never touch
these power sources should it ever fall. When installing
antenna, absolutely never touch power lines, circuits or
other power sources as this could be fatal.
USING THE UNIT
Before unit is brought out of storage or moved to a new location,
refer again to the INSTALLATION section of these safeguards.
1 KEEP UNIT WELL AWAY FROM WATER OR
MOISTURE, such as vases, sinks, tubs, etc.
2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG
IMPACT, unplug unit and have it inspected by a qualified
service technician before use.
3 ELECTRICAL STORMS
During a lightning storm, or before leaving unit unused for
extended periods of time, disconnect all equipment from the
power source as well as the antenna and cable system.
4 WHEN UNIT IS PLUGGED IN
• DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, malodors, or noises.
Immediately unplug unit, and have it inspected by a service
technician to avoid potential fire and shock hazards.
• Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire hazard.
• Keep magnetic objects, such as speakers, away from unit
to avoid electrical interference.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING UNIT
Unplug unit. Use a clean, dry, chemically untreated cloth to gently
remove dust or debris. DO NOT USE cleaning fluids, aerosols, or
forced air that could over-spray, or seep into unit and cause
electrical shock. Any substance, such as wax, adhesive tape, etc.
may mar the cabinet surface. Exposure to greasy, humid, or dusty
areas may adversely affect internal parts.
SERVICE
1 DO NOT SERVICE PRODUCT YOURSELF
If, after carefully following detailed operating instructions, the
unit does not operate properly, do not attempt to open or
remove covers, or make any adjustments not described in the
manual. Unplug unit and contact a qualified service technician.
2 REPLACEMENT OF PARTS
Make sure the service technician uses only parts specified
by the manufacturer, or have equal safety characteristics as
original parts. The use of unauthorized substitutes may
result in fire, electric shock, or other hazards.
3 SAFETY CHECK AFTER SERVICING
After unit is serviced or repaired, request that a through safety
check be done as described in the manufacturer’s service
literature to insure video unit is in safe operating condition.
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:consumerproducts@panasonic.com
Safety Precautions/Mesures de sécurité
Warning : To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
Caution : To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement : Afin de prévenir tout risque d’incendie ou de chocs électriques, ne
pas exposer cet appareil à la pluie ou à une humidité excessive.
Attention : Pour éviter les chocs électriques, introduire la lame la plus large de la fiche
dans la borne correspondante de la prise et pousser jusqu’au fond.
This video recorder, equipped with the HQ (High Quality) System, is compatible with
existing VHS equipment. Only use those tapes with the
mark. It is recommended that
only cassette tapes that have been tested and inspected for use in 2, 4, 6, and 8 hour
VCR machines be used. This television receiver provides display of television closed
captioning in accordance with §15.119 of the FCC rules.
FCC WARNING : Any unauthorized changes or modifications to this
equipment would void the user’s authority to operate.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated voltage within the unit may
have sufficient magnitude to cause electric shock. Therefore, it is
dangerous to make any kind of contact with any inside part of this unit.
This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any problems.
Congratulations
on your purchase of one of the most sophisticated
and reliable products on the market today. Used
properly, it will bring you and your family years of
enjoyment. Please fill in the information below.
The serial number is on the tag located on the
back of your unit.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
Accessories
Remote Control
LSSQ0308
(PVQ-1312W)
LSSQ0280
(PVQ-1312B
/PVQ-2012/PVQ-2512)
Batteries 2 “AA”
To order accessories,
call toll free 1-800-332-5368.
3
Head Cleaning
V I DEO HEADS MAY
NEED CLEAN I NG
PL EASE I NSERT HEAD
CLEAN I NG CASSETTE
OR REFER TO MANUAL
END : PLAY KEY
Record/Playback Time
Only use tapes with the
SP (Standard Play)
1 Hour
LP (Long Play)
2 Hours
SLP(Super Long Play) 3 Hours
4
mark in this unit.
2 Hours
40 Minutes
5 Hours
20 Minutes
8 Hours
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:consumerproducts@panasonic.com
Table of Contents
Initial Setup
Important Safeguards and Precautions / Safety Precautions .. 2, 3
Before Using....................................................................................... 3
Unit Information ................................................................................. 4
Table of Contents ............................................................................... 5
Location of Controls ........................................................................... 6
Connections / Initial Setup (Ready to Play) ................................. 8, 9
Basic Operation
Reset Language, Channels, Clock, Time Zone Adjust ........... 10, 11
Playback a Tape ................................................................................ 12
Record On a Tape ............................................................................. 12
Copy Your Tapes (Dubbing) ............................................................ 13
TV Operation
TV Operation .................................................................................... 14
Picture Adjustment .......................................................................... 15
TV Timer Features ..................................................................... 16, 17
Closed Caption System ............................................................. 18, 19
Timer Operation Advanced Operation For Your Information
Timer Recording ........................................................................ 20, 21
Tape Operation........................................................................... 22~24
Special VCR Features ............................................................... 25, 26
V-Chip Control Feature ............................................................. 27~29
On-Screen Display (OSD) ................................................................ 30
Before Requesting Service .............................................................. 31
Servicenter List ................................................................................. 32
Limited Warranty .............................................................................. 33
Spanish Quick Use Guide / Guía para rápida consulta ......... 34, 35
Index .................................................................................................. BC
5
Location of Controls
Remote Control Buttons
EJECT button:
When EJECT is pressed, the tape is ejected from Cassette Compartment.
If EJECT is pressed during recording, the unit will not respond to the command.
6
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:consumerproducts@panasonic.com
Initial Setup
Front View of the unit and Indicators on the Front Panel
<Model PVQ-2012 unit shown>
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
Built-In Speaker
PHONES Jack
Connect an
earphone or
headphones.
AUDIO VIDEO IN Jack
For dubbing.
REWIND/SEARCH
See previous page.
POWER
ACTION
Press together with STOP.
PROG TIMER
Indicator
VOLUME UP/DOWN
SET/BACK SPACE
PLAY
See previous page.
REPEAT
Lights when the
unit is set for
Timer Recording.
See previous page.
See previous page.
Repeats a recording.
CHANNEL UP/DOWN
TRACKING UP/DOWN
SELECT UP/DOWN
See previous page.
Lights when the
On-Timer is set.
See previous page.
STOP/EJECT
REC Indicator
REC
See previous page.
Lights during
recording.
TIMER
Remote Sensor
Sets a timer alarm up 60.
See above.See
previous page.
See previous page.
ACTION
Press together with REW.
ON TIMER
Indicator
FAST FORWARD/
SEARCH
Rear View of the Unit
<Models PVQ-1312W/PVQ-1312B unit shown>
Easy Grip-Handle
Use when transporting the unit.
AC Power Plug
When plugged into
an AC outlet, the
unit consumes 2.5 W
of electric power in
OFF condition.
VHF/UHF
VHF/UHF Antenna
Input Terminal
In from your Antenna or Cable.
Page 8.
7
Connections/ Initial Setup (Ready to Play)
Please make all cable or antenna connections before plugging into
the
ACto
outlet.
Plugging the unit power cord into an AC outlet starts
How
Connect
auto channel and clock set.
Connecting
IN from
ANT./CABLE
For ANT./Cable
Connect the cable from
Antenna/Cable to the VHF/UHF
terminal on the unit.
VHF/UHF
VHF/UHF
VHF/UHF
UNIT
For DSS/Cable Box
Connect the OUT jack on your
cable box to the VHF/UHF
terminal on the unit with a RF
cable.
Cable TV
Converter Box
VHF/UHF
WARNING:
Overtightening "Nut type" RF coaxial cables
may damage jacks. Finger tighten only.
VHF/UHF
IN from
ANT./CABLE
Initial Setup (Ready to Play)
1
2
Plug the unit power cord into an
AC wall outlet.
Press Power* on the remote or
unit. The unit comes on and auto
channel and clock set starts.
3
Settings are made
automatically. When setup is
done, this screen appears.
2 / 6 / 2002 WEDDST
12::ON
00PM
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
CH AUTO SET PROCEEDING
• If you use a cable box, turn it on and set it to the
Public Broadcasting Service (PBS) channel in
your time zone. If you use a DSS reciever, it
must be turned off.
If AUTO CLOCK SET IS
INCOMPLETE screen
appears, set the clock using
MANUAL CLOCK SET
procedure on next page.
AUTO CLOCK SET
AUTO CLOCK SET
I S I NCOMPLETE
PROCEEDING
CANCEL : PRESS STOP KEY
8
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:consumerproducts@panasonic.com
Reset all unit Memory Functions
1
Press ACTION on the Remote to
display SET CLOCK Menu screen.
Initial Setup
Manual Clock Set
If AUTO CLOCK SET was incomplete, manually
set the clock as follows.
When moving unit to a new location, or if a
mistake was made in the Initial Setup section.
• Make sure a tape is not inserted in the unit.
<Model PVQ-2012 unit shown>
SET CLOCK
:
1/ /
DST : ON
SELE CT MONTH
POWER
SELECT :
SET
:
END
: ACT I ON
2
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
to select the month
Press
and press to set. In the same
manner, select and set the date,
year, time, and DST. (Daylight
Saving Time)
1
Turn the unit
Power on.
2
Press and hold both PLAY and
FF on the unit for more than 5
seconds.
• The power will shut off.
• Please ignore “NO CASSETTE” warning.
SET CLOCK
2 / 6/2002 WED 12: 00PM
DST : ON
3
SELE CT COMPLETED
SET
END
3
Do “Initial Setup” on page 8.
:
: ACT I ON
Press ACTION twice to start
CLOCK and exit.
POWER
ACTION
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
Note to CABLE System Installer
This reminder is provided to call the
CABLE (Cable TV) System Installers
attention to Article 820-40 of the NEC
that provides guidelines for proper
grounding and, in particular, specifies
that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable
entry as practical.
9
Reset Language, Channels, Clock,
1
Press ACTION
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
to display MAIN MENU.
SELECT :
SET
: ACT I ON
2
Language
1) Press
to
select language
icon.
Clock
Channels
1) Press
select “CH.”
to
1) Press
to
select “CLOCK.”
M A I N MENU
M A I N MENU
M A I N MENU
TV
VCR
CH
LANGUAGE
EX I T
CLOCK
SELECT :
SET
: ACT I ON
TV
VCR
LANGUAGE
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
2) Press ACTION.
2) Press ACTION
repeatedly.
MENU PR I NC I PAL
HOLA
TV
VCR
IDIOMA
CANAL
REL OJ
SAL I R
ELEG I R :
F I JAR : ACT I ON
For Spanish
MENU
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
:
END
: ACT I ON
3) Press
to select
“ANTENNA,” then
press to set your
antenna system
(“TV” or “CABLE”).
BONJOUR
T ELE
LANGUE
MAGNET .
CANAL HORLOGE SORT I E
SEL.
:
REGLER : ACT I ON
For French
M A I N MENU
HELLO
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
For English
3) Press
to
select “EXIT.”
Press ACTION to
exit.
10
to select
4) Press
“AUTO SET,” then
press .
• After Channel Auto Set is
finished, Clock Auto Set
will be performed. (If clock is
set manually, Clock Auto
Set will not be performed.)
SELECT :
SET
: ACT I ON
2) Press ACTION.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SELECT :
SET
:
END
: ACT I ON
(“TIME ZONE ADJUST”
appears only when auto
clock is set.)
3) Press
to select
“MANUAL” or
“AUTO CLOCK
SET” and press .
• For Auto Clock Set,
select “AUTO CLOCK
SET,” then press .
SET CLOCK
2 / 6/2002 WED 12: 00PM
DST : ON
SELE CT HOUR
SELECT :
SET
:
END
: ACT I ON
4) Press
and
press
to select
and set the month,
date, year, time,
and DST (Daylight
Saving Time).
5) Press ACTION
twice to start the
clock and exit this
mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Time Zone Adjust
POWER
NUMBER Keys
ADD/DLT
Time Zone Adjust
(Only when Auto Clock is set.)
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
ACTION
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
Basic Operation
1) Press
to
select “CLOCK.”
SELECT :
SET
: ACT I ON
2) Press ACTION.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
ACTION key on
the unit
Using
SELECT :
SET
:
: ACT I ON
END
3) Press
to
select TIME ZONE
ADJUST and
press or to
subtract or add
hour(s) as
necessary.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : +1
SELECT :
SET
:
: ACT I ON
END
4) Press ACTION
twice to exit.
keys
VOL
On Unit
You can operate the
menu screen using
unit buttons. To display
the menu, press STOP/
EJECT and REW
together with no tape
inserted. To exit the
menu, repeat above
with or without tape
inserted until normal
screen appears.
On Remote
CH
On Unit
: CH UP
: CH DOWN
: VOLUME UP
: VOLUME DOWN
Whenever the menu or
program screen is displayed,
CHANNEL UP/DOWN function
as
and VOLUME UP/
only.
DOWN function as
Add or Delete a Channel
To add channel:
To delete channel:
Select channel with
number keys and
press ADD/DLT.
Select channel with
CH
or number keys
and press ADD/DLT.
CHANNEL 08 ADDED
CHANNEL 08 DELE TED
11
Playback a Tape
Ready Check List
All connections are made.
Your unit is plugged in.
1
Insert a cassette.
• The unit power comes
on automatically.
Record
tab
To prevent tape jam,
remove loose or peeling
labels from tapes.
2
Press PLAY.
• Playback begins if cassette has no record
tab.
■ Forward/Reverse scene search
=> Press FF or REW
=> PRESS again or PLAY to release.
■ Still (Freeze) picture
=> Press PAUSE/SLOW
=> Press PLAY to release.
■ Slow Motion picture
=> Hold down PAUSE/SLOW in
Still mode
=> Press PLAY to release.
■ Frame by Frame picture
=> Press PAUSE/SLOW in Still mode
=> Press PLAY to release.
Notes
• These features work best in SP or SLP mode.
• After the unit is in Still or Slow mode for 3
minutes, it will switch to Stop mode automatically
to protect the tape and the video head.
■
■
■
■
Record On a Tape
1
2
3
Insert a cassette with record tab.
• The unit power comes on automatically.
Press CH
or number keys
to Select Channel.
• For “LINE” input, see bottom of next page.
Press SPEED to select recording
speed (see page 4).
SP = Standard Play
LP = Long Play
SLP = Super Long Play
• Selected speed is displayed.
4
Press REC to start recording.
• To edit out unwanted portions, press
PAUSE/SLOW to pause and resume
recording.
• You cannot view another channel during
recording.
■ Stop => Press STOP
■ One Touch Recording (OTR)
Press REC repeatedly Normal Rec
to set the recording
length (30 min - 4 hours). 4:00 3:00
0:30
2:00
1:00
1:30
• The unit stops recording at a preset time.
• PROG TIMER indicator lights on the unit.
Notes
• After the unit has been in Rec Pause mode for
5 minutes, it will stop automatically to protect
the tape and the video head.
• The remaining recording time of an OTR can be
displayed by pressing DISPLAY.
Stop => Press STOP
Rewind tape => Press REW in Stop mode
Fast forward tape => Press FF in Stop mode
Eject tape => Press EJECT on the remote or
STOP/EJECT on the unit
You can operate on the unit
■ Press to stop and/or eject tape. REC Indicator
12
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Copy Your Tapes (Dubbing)
Connections you’ll need to make.
Recording (Editing) unit
Playing (Source) VCR
AUDIO VIDEO
OUT
OUT TO TV
Playback (Source)
1
2
3
Recording (Editing) unit
Insert blank tape with
record tab.
Insert prerecorded tape.
• Dubbing tapes protected
with Copy Guard will have
poor quality results.
Our Vacation
Select “LINE” mode.
See “Selecting Input Mode” below.
Press PLAY then
Press REC, then
PAUSE at starting
PAUSE/SLOW
point to put in
immediately to put in
Standby mode.
Standby mode.
(Perform operation of steps 4 and 5 on both units at same time.)
4
5
VIDEO IN AUDIO IN
AUDIO IN
STOP
Press PLAY
to start dubbing.
Press PAUSE/SLOW
to start dubbing.
Press STOP
to stop dubbing.
Press STOP
to stop dubbing.
Selecting Input Mode
Method 1:
Press CH
. The display will change as follows.
1
Caution
• Unauthorized exchanging
and/or copying of copyrighted
recordings may be copyright
infringement.
2
3
(CABLE) (TV)
125 or 69
LINE
Method 2:
a Press ACTION for MAIN MENU.
b Press
to select “TV”, then press
ACTION for SET UP TV screen.
c Press
to select “INPUT SELECT,” and
then press to select “TUNER” or “LINE.”
d Press ACTION twice to exit this mode.
13
Basic Operation
IN
IN FROM ANT.
TV Operation
1
2
Press POWER on the remote or unit.
Ready Check List
All connections are made.
Your unit is plugged in.
08
ABC
3
Use CH
or
number keys to
select a channel.
Press VOL + or VOL
- to adjust volume.
<Model PVQ-2012 unit shown>
24
VOL + / VOLPLAY/
REPEAT
NIGHT (NITE) Mode
POWER
VOL
CH
STOP/EJECT REW/
N I GHT
• NIGHT mode may be
selected when watching TV
or playing a tape.
REC TIMER/FM
AUDIO IN
ACTION
Color and picture intensity levels are adjusted so the screen
is easier on your eyes during night time use.
Press NITE to set
NIGHT mode.
PLAY/REPEAT FF/
REC ON TIMER PROG TIMER
VIDEO IN
CH
PHONES
Jack
POWER
Press NITE to cancel.
• Previous settings are restored.
• NIGHT mode is canceled
when power is turned off or
power failure occurs.
■ Using the 100 key
When selecting CABLE channels 100 to 125 with the number keys, first press the 100
key, and then enter the remaining two digits.
■ Rapid Tune
Press R-TUNE to display the last channel you were watching.
■ Audio Mute
Press MUTE to instantly mute the sound. Press again to restore the previous sound level.
■ Phones
Connect an earphone (not supplied) or headphones (not supplied) to the Phones Jack.
14
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:consumerproducts@panasonic.com
Picture Adjustment
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
POWER
NITE
100 Key
NUMBER
Keys
RAPID
TUNE
SELECT :
SET
:
END
: ACT I ON
CH UP/
DOWN
VOL UP/
DOWN
ACTION
SET UP TV
LOCK
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
4
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
NORMAL
SELECT :
ADJUST :
END
: ACT I ON
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
NORMAL
SELECT :
SET
:
END
: ACT I ON
Picture Adjustment
■ COLOR Control
Adjust color intensity.
5
: TUNER
1) Press
to select
VIDEO ADJUST.
2) Press to display
screen.
1) Press
to select
an adjustment item.
(See below left.)
2)Press
to
adjust.
To Reset Picture
Controls.
Press
and to
select and set
“NORMAL.”
All controls return to
their factory settings.
Press ACTION three times to exit.
■ TINT Control
Adjust for natural flesh tones.
■ BRIGHTNESS Control
Adjust picture brightness.
■ PICTURE Control
Adjust picture intensity by
adjusting both contrast and
color level in the proper
balance.
■ SHARPNESS Control
Adjust picture sharpness.
15
TV Operation
MUTE
3
1) Press
to
select “TV.”
2) Press ACTION to
display SET UP TV
screen.
TV Timer Features
ON-TIMER with Alarm
This unit can be set to automatically power on in one of 2
modes (TV, Playback).
You can also combine the On-Timer with a one minute alarm
that gradually increases in volume.
1
2
Press PROG to display SET PROGRAM
screen.
SET PROGRAM
T I MER PROGRAMMING
ON TIMER
SELECT :
SET
:
END
: PROG
3
Ready Check List
The clock is set to correct time.
<Model PVQ-2012 unit shown>
1) Press
to select
desired settings.
2) Press to set the
ON-TIMER TIME or
ON-TIMER mode.
ON T I MER
6:--AM CH -ALARM : ON
SELE CT HOUR
SELECT :
SET
:
END
: PROG
• ON-TIMER mode
selection order
CH02
1)Press
to select
“ON TIMER.”
2)Press to display
ON TIMER screen.
CH03
• Make sure a tape is
inserted if Playback
mode is selected.
TIMER
CH125
CH01
PLAY
4
ON T I MER
6:00AM CH08
ALARM : ON
ABC
SELE CT ALARM
CANCEL : ADD / DLT
SELECT :
SET
:
END
: PROG
CH
Press
to select
ALARM “ON” or
“OFF.”
ON TIMER
indicator
When “ON” is selected,
an alarm will gradually increase in volume for one
minute or until canceled by pressing any button
(including VOL + -).
To Make Corrections,
use
and
to move back and correct.
5
Press PROG to set ON TIMER.
• “ON TIMER SET” is displayed.
• ON TIMER Indicator lights on the unit.
Note
To Cancel ON-TIMER set,
Repeat steps 1 and 2. Then, press ADD/DLT to
clear the time in step 3. Now, press PROG to end.
“ON TIMER END” briefly appears on-screen.
16
• If no button on the remote or unit
(including a button used to turn off
the alarm) is pressed within 60
minutes after unit turns itself on,
it will turn itself back off.
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:consumerproducts@panasonic.com
Sleep Timer
This unit can be set for auto power off.
Press SLEEP repeatedly
to set SLEEP TIMER.
SLEEP TIMER 30
• Pressing DISPLAY with
sleep timer set displays
remaining time.
SLEEP TIMER 60
Press SLEEP repeatedly
until “SLEEP TIMER 00”
appears to cancel.
SLEEP TIMER 90
SLEEP TIMER 00
Instant Alarm
1
2
1:00 (one minute)
2:00
3:00
Press TIMER on the unit to display the
instant alarm CANCEL/SET screen.
5 : 20PM
02 : 00
CANCEL : ADD / DLT
SET : CH
KEY ON UN I T
one-minute
increase
until 10:00
Press CH
on the
unit with CANCEL/SET
screen displayed to set
alarm. (Time changes in
the order shown left.)
Remaining Time
• Pressing TIMER repeatedly on the unit
will change display as follows.
9:00
10:00
15:00
20:00
25:00
five-minute
increase
until 30:00
30:00
40:00
50:00
ten-minute
increase
until 60:00
To cancel, press TIMER then press ADD/DLT on
the remote while CANCEL/SET screen is displayed.
To increase timer in progress, repeat step 2. Time
will be rounded up to next 1, 5, or 10 minute interval.
(See chart left.)
60:00 (Max)
<Example>
• If current time remaining is 12:15, countdown will
restart from 15:00.
• If current time remaining is 9:15, countdown will
restart from 10:00.
Note
• While timer function is in progress,
you can change channels on the unit
with CH
while “CANCEL/SET”
screen is not displayed.
3
Alarm will sound at 0: 00.
Press any button to stop
• The volume of the alarm gradually increases
for one minute and then continues to beep
until any button is pressed.
17
TV Operation
You can set a timer alarm up to 60 min. Useful when you are
cooking, etc.
Closed Caption System
Closed Caption is ...
This multi-use system not only allows the hearing impaired to enjoy selected programs,
but also makes useful information from TV stations available to everyone.
Closed Caption Mode Feature
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP TV
LOCK
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
: TUNER
SELECT :
SET
:
END
: ACT I ON
4
: CAP C1
: CAP C1
SELECT :
SET
:
END
: ACT I ON
OFF
CAP C1
TEXT C2
to
1) Press
select “CAPTION”.
2) Press to display
CAPTION screen.
Caption Mode: CAP C1 or C2
A narration of selected TV
programs is displayed.
Check TV program listings for
CC(Closed Caption)
broadcasts.
Caption Mode: TEXT C1 or
C2
The lower half of the screen
will be blocked out. When the
TV station broadcasts
information, such as program
listings, it will appear in this
space.
Caption Mode: OFF
Closed Caption / Text narration
will not be displayed.
CAPT I ON
CAPT I ON MODE
CC ON MUTE
1) Press
to
select “TV.”
2) Press ACTION to
display SET UP
TV screen.
Closed Caption Mode
Selections
1) Press
to
select CAPTION
MODE.
2) Press
repeatedly to
select mode.
(See left.)
NOTE :
The closed caption or text
signal may be broadcast over
C1, C2, or both. Also, text
contents can vary so you may
wish to try different settings.
TEXT C1
CAP C2
5
Press ACTION three times to return
to the normal screen.
Recording and Playing Back a Closed Caption/Text Program
Record:
Record normally.
Closed Caption/ Text signal, if present, is recorded automatically.
Playback: Start playback. Do above steps to select desired caption mode.
18
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:consumerproducts@panasonic.com
Caption On Mute Feature
Closed Caption narration, if available, is displayed
when MUTE button is pressed for silence.
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
: TUNER
SELECT :
SET
:
END
: ACT I ON
4
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: OFF
: CAP C1
SELECT :
SET
:
END
: ACT I ON
5
to
1) Press
select CAPTION
MODE.
2) Press
repeatedly to
select “OFF.”
1) Press
to select
CC ON MUTE.
2) Press repeatedly
to select desired
mode.
NO
CAP C1
CAP C2
6
7
to
1) Press
select “CAPTION”.
2) Press to display
CAPTION screen.
• Each press of will
change the display as
shown left.
• The caption may be
broadcast over CAP C1
or C2.
Press ACTION three times to return to
the normal screen.
Press MUTE to mute the sound and
display closed captioning.
• To cancel, press MUTE again.
19
TV Operation
3
SET UP TV
LOCK
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
to
1) Press
select “TV.”
2) Press ACTION to
display SET UP TV
screen.
20
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Cancel a Timer Recording:
(Recording is in progress)
Hold down STOP for a few seconds
to cancel the Timer Recording.
• Any future daily or weekly recordings
will be performed as programmed.
Review, Replace or Clear Program
Contents : (Recording is not in progress)
1
2
Repeat steps 1 and 2 on page 20.
P
1
2
3
4
DT START STOP CH SPD
day 9 : 00p 12 : 00a 08 SP
8 10 : 00a 12 : 00p 125 SP
10 8 : 00p 9 : 00p 10 SP
SU 9 : 00p 10 : 00p L LP
Press
to select
the desired program.
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER :
END
: PROG / ACT I ON
3
To Replace program...
1) Press to display.
START
STOP
CH
to select
8 SAT 9:00P 12:00A 08 2) Press
ABC
TODAY
and press or
SP
---------------------------------------------to set new program
SELE CT START DATE
SELECT :
contents.
SET
:
END
: PROG / ACT I ON
3) Press PROG (or
ACTION).
DATE
ADD/DLT
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
To Clear program...
PROG
DT START STOP CH
-- -- : -- -- : -- -8 10 : 00p 12 : 00a 125
10 8 : 00p 9 : 00p 10
SU 9 : 00p 10 : 00p L
SPD
-SP
SP
LP
Press ADD/DLT.
Timer Operation
P
1
2
3
4
SELECT 1 - 8 :
ENTER :
END
: PROG / ACT I ON
STOP
4
Press PROG twice (or ACTION)
to exit this mode.
Notes
• 2 minutes before Timer recording is performed,
“PLEASE PREPARE FOR TIMER REC” appears and/
or the PROG TIMER Indicator flashes. Be sure a
cassette with record tab is loaded and the unit is in
Stop mode.
• If the start times of two programs overlap, the lower
numbered program will have priority.
• If the start time for a Timer Recording comes up during
a normal recording or One Touch Recording (page 12),
the Timer Recording will not be performed.
• If there is a power interruption of more than one minute,
the recording may not be performed or continued.
• If “INCOMPLETE” appears after all items have been
set, check all entries and make necessary corrections.
21
Tape Operation
Search System is ...
Each time a recording is made, an invisible index mark is placed on the tape.
When timer recordings are made, program index and information are also included.
These index marks can be used to access or scan recordings.
Program End Search
Index Search
Go directly to the desired recording.
Locates end point of recording for continuity.
1
1
2
I NDEX SEARCH
ENTER I NDEX NUMBER : 1
US I NG 1- 9 KEYS
FORWARD SEARCH : FF
REVERSE SEARCH : REW
NEXT : SEARCH
EX I T : STOP
2
Press SEARCH in
Playback or Stop
mode to display
INDEX SEARCH
screen.
Press SEARCH twice in Playback
or Stop mode to display
PROGRAM END SEARCH screen
.
Press FF to
PROGRAM END SEARCH
start search.
Press number
keys to select the
recording number.
I NDEX SEARCH 3
I NDEX SEARCH
• To calculate number,
see below.
SEARCH START : FF
EX I T : SEARCH
Example of Program End Search operation.
Fig.1
FORWARD SEARCH : FF
REVERSE SEARCH : REW
Press SEARCH button
FF
Program 2 or BLANK
End Point
Fig.2
Program 1
INDEX
• Play begins at search
end. To search
forward or back 1
index, press FF or
REW while screen left
in displayed (10
seconds).
INDEX
3
Press FF or REW
to start search.
I NDEX SEARCH
PLAYBACK DIRECTION
Program 1
BLANK
Program 2
BLANK
Press SEARCH button
End Point
FF
Fig.3 If search exceeds a few seconds in BLANK area.
Press SEARCH button
To go to rec. 2 from rec. 4, enter 3 and press REW.
2
3
4
5
6
7
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
1
2
BLANK
Program 2
FF
Example 1:
1
Program 1
INDEX
■ To calculate the Index Number
3
4
5
6
7
End Point
Upon locating end point...
The unit searches slightly past end point,
reverse searches, and plays the last few
seconds of the program, then stops.
Press SEARCH button
NOTE: indicates start points of each recording.
Notes
Notes
• Make each entry within 10 seconds, or the Index
Search mode will be canceled.
• If Index Search is started very close to an index
mark, that index mark may not be counted in the
search.
22
• If Program End Search is started very
close to an index mark, that mark may be
skipped over.
• To cancel, press PLAY or STOP.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Auto Operation Functions
<Model PVQ-2012 unit shown>
■ Auto Shut Off
No broadcast signal in TV, blank tape is
Played for 5 minutes
=> Power turns off
• This feature is canceled if any button is
pressed during above mode.
■ Auto Playback
Insert a tape in Power off mode
=> Power turns on
• Playback begins if tape has no record tab.
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
FF
REW
■ Auto Rewind
Tape reaches its end
=> Rewind => Stop
■ Playback Auto Eject (Repeat Play is “OFF”)
Tape with no record tab reaches its end
Rewind => Stop => Eject
Tape Position Display
To find out present tape position and amount of tape
remaining.
Tape position cannot be detected for
C-Cassettes, tapes under 30 minutes, and some
other tapes.
1
Press TAPE POSITION to detect
current tape position.
2
• “DETECTING TAPE POSITION”
is displayed only when a
cassette is first inserted and it
takes several seconds for
correct tape position to appear.
• The present tape position
indication and amount of tape
remaining (according to tape
speed) is displayed.
• Tape remaining time display may
not be precise.
Press TAPE POSITION (or wait 5
seconds) to return to normal screen.
Note
• This function cannot display exact amount of
tape remaining for tapes 30 minutes or less, or
for tapes over 120 minutes in length.
23
Advanced Operation
DETECT I NG TAPE POS I T I ON
Tape Operation (continued)
Zero Search
Repeat Play
To quickly return to a specific tape counter location.
Set to see a recording over and over.
1
2
1
2
Press DISPLAY during playback to
display the Counter.
0 : 00 : 00
BEG I N
3
4
5
Press COUNTER
RESET at the
desired position to
reset to “0:00:00.”
1) Press
to select “VCR.”
2) Press
ACTION to
display SET
UP VCR
screen.
END
Continue playback, rewind, or
fast forward.
Press STOP.
1 : 23 : 45
Press CM/ZERO
in stop mode to
start ZERO
SEARCH.
•
BEG I N
Press ACTION to display
MAIN MENU.
END
: Present position mark
: Zero position mark
• Unit goes into FF or REW mode and stops at
the last point the Counter was set to 0:00:00.
Note
• If a blank portion exists on the tape, and
depending on the position of the mark, the
mark display may be out of position.
3
4
1)Press
to
select
“REPEAT
PLAY.”
2)Press to
set REPEAT
PLAY “ON” or
“OFF.”
Press ACTION twice
to end setup.
Notes
• Playback repeats when tape end is reached or
unrecorded portion over 30 seconds is detected.
• During playback, you may also press PLAY/
REPEAT repeatedly on the unit to select
REPEAT “ON” or “OFF.”
Commercial Skip
By pressing the CM/ZERO button in Playback mode
you can skip over 1 to 3 minutes of recorded tape in
just a few seconds.
1
24
Press CM/ZERO repeatedly to
select skip time in Play mode.
• No indication appears.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Special VCR Features
Weak Signal Display ON/OFF
When “ON” is selected, the picture is displayed even
when a broadcast signal is weak or non-existent.
1
2
Press ACTION to display MAIN
MENU.
1) Press
to select “CH.”
2) Press ACTION
to display SET
UP CHANNEL
screen.
3
1)Press
to
select WEAK
SIGNAL
DISPLAY .
2)Press to set
“ON” or “OFF.”
Notes
• “ON” = Picture is displayed regardless of signal
condition, and may not always be clearly
visible.
“OFF” = Screen turns solid blue when signal is
absent or weak.
• If unit is connected to equipment which has blue
back feature, selecting “ON” will have no effect on
the other equipment.
4
VCR Lock
All operations are prohibited except Timer recording
and tape eject. Useful for families with small children.
In stop mode, hold
down REC on the unit
without a cassette
inserted for 7 seconds
to turn “ON.” Please
ignore NO CASSETTE
warning.
Repeat above with or
without cassette to
turn “OFF.”
REC
• VCR Lock is canceled automatically
after about 24 hours if clock is set.
• “Auto power on” is not prohibited when
VCR Lock is activated.
25
Advanced Operation
<Model PVQ-2012 unit shown>
Press ACTION twice
to return to the normal screen.
Special VCR Features (continued)
Channel Caption is ...
Station names, e.g. ABC, TNN, etc. are set so they
will appear when a channel is selected. Choose 24
preset names.
Preset Caption
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
:
END
: ACT I ON
4
PRESET CAPT I ON
ABC
CBS
FOX
NBC
-----
PBS
CNN
ESPN
HBO
-----
SELECT :
SET
:
END
: ACT I ON
PRESET CAPT I ON
62
TNT
4 2 CBC
UPN
-- CTV 2 1
52
WB
3 5 TSN
DSC
-- GLOB 1 2 3
CLEAR : ADD / DLT KEY
SELECT :
SET
:
END
: ACT I ON
1)Press
to select “CH.”
2)Press ACTION
to display SET
UP CHANNEL
screen.
1) Press
to
select CHANNEL
CAPTION.
2) Press to
display screen.
1)Press
to
select a station.
2)Press to
move cursor to
the right.
3)Press
to
select channel
number.
4)Press to set
preset captions.
NUMBER Keys
ADD/DLT
ACTION
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
• Repeat step 4 until the
Caption List is complete.
To Make Corrections
Press
Press
5
26
, then to select channel number.
to change, or ADD/DLT to delete.
Press ACTION four times to end setup.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
V-Chip Control Feature
Process of V-Chip Control
Feature
Enter Code
Setup
Blocking
V-Chip Control Feature is...
This unit has a built-in V-Chip Control which allows
you to block unwanted TV usage based on US
MOVIES and US TV PROGRAMS Ratings.
Enter Secret Code
A 4-digit code must be entered to view a blocked program or
change rating settings.
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP TV
LOCK
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
: TUNER
SELECT :
SET
:
: ACT I ON
END
4
LOCK
ENTER 4-D I G I T CODE
---ENTER : 0 - 9
: ACT I ON
END
1) Press
to
select “TV.”
2) Press ACTION to
display SET UP TV
screen.
1) Press
to select
LOCK.
2) Press to display
screen.
1)Press number
keys to enter your
secret code.
2)Enter same code
again for confirmation.
5
LOCK
CONF I RM 4-D I G I T CODE
****
****
RECOGN I ZED
CHANGE CODE : ADD / DLT
CONT I NUE :
END
: ACT I ON
Press to display US
Ratings menu
(see page 28).
Or
Press ACTION
three times to exit.
Changing your secret code
• You will need your current
code. Do steps 1 ~ 4. In step
5, press ADD/DLT to clear
current code. Repeat steps 4
and 5 to enter new code.
Notes
• DO NOT forget your secret code.
• Once ratings are set, restricted tapes
or programs cannot be accessed
unless the secret code is entered.
27
Advanced Operation
• Step 2) not necessary
To Make Corrections
when changing rating
Press repeatedly to
or secret code.
move the cursor. Press • Take care that you are
number keys to make
not observed entering
the correction.
the secret code.
Enter Code
Setup US MOVIES Ratings
1
1) Press
to
select US
MOVIES.
2) Press to set
Note
Setup US TV PROGRAMS Ratings
1
1) Press
to
select US TV
PROGRAMS.
2) Press to set
“ON” or “OFF.”
Note
• “NEXT PAGE” displays CANADIAN V-Chip
setting menu. Not necessary except when
viewing Canadian tapes or broadcasts.
• “NEXT PAGE” displays CANADIAN V-Chip setting
menu. Not necessary except when viewing
Canadian tapes or broadcasts.
2
1)Press
to
select
CHANGE
SETTINGS.
2) Press to
display screen.
2
1)Press
to
select
CHANGE
SETTINGS.
2)h6
3
1) Press
to select
VIEW NR
PROGRAMS?.
2) Press to set
“YES” or “NO.”
3
1)Press
to select
VIEW NR
PROGRAMS?.
2)Press to set
“YES” or “NO.”
NR (Not Rated) PROGRAMS
Some TV shows, such as news, sports,
weather, bulletins, emergency
information usually have no ratings.
NR (Not Rated) PROGRAMS
Some movies, such as old movies or
foreign movies usually have no ratings.
4
Press
to
select and to
set ratings to be
blocked.
(See ratings
chart next page.)
5
Press ACTION to redisplay LOCK
menu and continue with US TV
PROGRAMS Ratings Setup (this
page).
Or, press ACTION four times to exit.
28
5
Press ACTION four times
to exit this mode.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
Blocking Message
<When V-Chip Control is activated>
• If a program or
ABC
movie exceeds the
ratings you have
PROGRAM RAT I NG EXCEEDED
set, a message will
RAT I NG : PG-1 3
ACCESS CODE
---appear on a black
ENTER : 0-9
background and
sound is muted.
To View a Blocked Program / Movie
[Temporarily Deactivate V-Chip Control]
Enter your secret code (ACCESS CODE)
in the Blocking Message screen.
US MOVIES RATINGS
G
PG
PG-13
R
NC-17
X
GENERAL AUDIENCE:
All ages admitted.
PARENTAL GUIDANCE:
Some material may not be suitable for
children.
PARENTS CAUTIONED:
Some material may be inappropriate
for children under 13.
RESTRICTED:
Children under 17 must be
accompanied by a parent or adult.
OVER AGE 17 ONLY:
No one 17 and under admitted.
ADULTS ONLY:
• V-Chip Control is reactivated when power is
turned off or power failure occurs.
[Deactivate V-Chip Control]
Enter your secret code (steps 1-4 page 27).
Then, set US MOVIES and/or US TV
PROGRAMS to “OFF” using
and
keys. (Ratings set on page 28 is retained
and will be in effect when V-Chip Control is
activated again.)
US TV PROGRAMS RATINGS:Chart 1
TV-Y
US TV PROGRAMS RATINGS: Chart 2
FV
V
S
L
D
Fantasy Violence
Violence
Sexual Situations
Adult Language
Sexually Suggestive Dialogue
29
Advanced Operation
FOR ALL CHILDREN:
Content specifically geared to young
viewers ages 2-6.
TV-Y7 FOR AGE 7 AND OLDER:
May contain mild physical or comedic
violence which may frighten children
under 7.
TV-G GENERAL AUDIENCE:
Contains little or no violence, strong
language, or sexual dialogue or
situations.
TV-PG PARENTAL GUIDANCE:
May contain infrequent coarse
language, limited violence, some
suggestive sexual dialogue and
situations.
TV-14 PARENTS CAUTIONED:
May contain sophisticated themes,
sexual situations, strong language, and
more intense violence.
TV-MA MATURE AUDIENCE:
May contain mature themes, profane
language, graphic violence, and sexual
situations.
On-Screen Display (OSD)
VCR Status & Clock Display
Press DISPLAY
to display or remove the overlay.
Channel Caption
(See page 26.)
Function Status
Current Time
Rec Time
Remaining
(OTR mode only,
see page 12.)
REC
0 : 25
Counter
ABC
1 2 : 0 0PM
-0 : 1 2 : 3 4
SP
Blue Screen Display
Whenever a blank section of a tape comes
up in Play mode, or when the selected
channel has no broadcast signal with the
Weak Signal Display set to “OFF” (see
page 25), the screen will turn solid blue.
Channel & Function Display
When a function button is pressed (PLAY,
FF, etc.) or you change channels, the unit
mode or channel number will be displayed.
(Some station names may also appear if
Channel Caption is set. See page 26.)
08
Tape Speed
Warning and Instruction Displays
ABC
These displays will alert you to a missed
operation or provide further instructions.
OSD
Caution
Page
PLEASE SET CLOCK BEFORE
PROGRAMMING
• If you attempt to set or review a Timer Recording,
or set the On-Timer and the Clock is not set...
8 - 11
CHECK CASSETTE RECORD TAB
• If you press REC, and a cassette is inserted with
no record tab...
3, 12
TO CANCEL TIMER REC HOLD DOWN
STOP KEY FOR APPROX 3 SEC
• If you press STOP during a Timer Recording...
21
NO CASSETTE
PLEASE INSERT A CASSETTE
• If you press PLAY, FF, REW, or REC without a
cassette inserted...
12
PLEASE PREPARE FOR TIMER REC
• If the unit is not in Stop mode or a cassette with
record tab is not inserted two minutes before a
Timer Recording is about to begin...
20, 21
VIDEO HEADS MAY NEED CLEANING
PLEASE INSERT HEAD CLEANING
CASSETTE OR REFER TO MANUAL
END: PLAY KEY
• If head cleaning becomes necessary while playing
back a tape...
4
VCR LOCK ACTIVATED
• If you press a function button other than STOP/EJECT
or POWER while the unit is in VCR Lock mode...
25
30
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Before Requesting Service
Check the following points once again if you are having trouble with your unit.
Power
Correction
No power…
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
Monitor
Correction
No picture or sound...
Poor picture with normal sound...
•
•
•
•
Poor sound with normal picture...
Poor TV reception...
No color or poor color...
Ghost (multiple) images...
TV programs cannot be watched...
Channel cannot be selected...
•
•
•
•
•
•
VCR
Correction
TV program cannot be
recorded...
•
•
•
•
Timer recording cannot be
performed…
•
•
No playback picture, or the playback •
picture is noisy or contains streaks... •
VCR cannot be controlled...
•
•
Make sure your antenna system (TV or CABLE), is correctly set. (P. 8)
Completely insert Power Plug into an AC outlet.
Set POWER button to ON.
Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in
the SET UP TV menu. (P. 15)
Adjust VOLUME control. (P. 14)
Adjust SHARPNESS and PICTURE controls in the SET UP TV menu. (P. 15)
Adjust TINT and COLOR controls in the SET UP TV menu. (P. 15)
Install a directional antenna.
Make sure the selected channel is in unit’s memory. (P. 10, 11)
Only the channel being recorded can be viewed on this unit.
Make sure your antenna system (TV or CABLE), is correctly set. (P. 8)
Make sure cassette record tab is intact. (P.3)
Check that clock is set to current time and date.
Make sure DSS/CABLE box (if used) is left on and tuned to
channel to be recorded.
Set recording Start/Stop times correctly. (P. 20-21)
Timer recording may not be performed or continued if a power
interruption of more than 1 minute occurs before or during a Timer
recording even after power is restored.
Adjust TRACKING control in either direction. (P. 4)
Try Head Cleaning. (P. 4)
Make sure VCR LOCK is set to off. (P. 25)
Make sure unit is not in a Timer Record operation.
Remote Control
Correction
Unit cannot be controlled...
• Aim remote at remote sensor on unit (P. 7) so that signal is
unobstructed.
• Inspect the remote batteries. (P. 3)
• Make sure VCR LOCK is set to off. (P. 25)
• Exposing unit remote sensor to direct fluorescent or outdoor light
may cause signal interference.
• Check remote batteries.
ACTION, PROG and FM/TV
buttons cannot be selected...
Correction
Video cassette cannot be inserted...
Video cassette cannot be removed...
Tape cannot be ejected or inserted...
Video cassette ejects when a
recording is started, or the power
is turned off for timer recording...
In Stop mode, the VCR motor
(CYLINDER) continues to rotate...
•
•
•
•
VCR cannot be controlled...
Insert the cassette window side up; record tab facing you.
Completely insert Power Plug into an AC outlet.
Try ejecting or inserting the tape again after turning POWER off, then back on.
Make sure cassette record tab is intact. (P. 3)
• To enable Quick Play mechanism, the VCR cylinder will rotate for
about 3 minutes. This reduces response time from Stop to Play
mode and from Play to Rewind Search mode.
• Make sure VCR LOCK is set to off. (P. 25)
If you cannot resolve the problem, please call the Customer Satisfaction Center for
product assistance at 1-800-211-PANA(7262).
To locate an authorized servicenter call toll free 1-800-211-PANA(7262)
or send e-mail to : consumerproducts@panasonic.com.
31
For Your Information
Miscellaneous
Service Center List
For Product Information, Operating Assistance, Literature Request, Dealer Locations,
and all Customer Service inquires please contact:
1-800-211-PANA(7262), Monday-Friday 9am-9pm Saturday-Sunday 9am-7pm, EST.
or send e-mail : consumerproducts@panasonic.com
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your
nearest servicenter by visiting our Web Site.
Accessory Purchases:
1-800-332-5368 (Customer Orders Only)
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST)
(Visa, Master Card, Discover Card, American Express, Check)
Factory Servicenter Locations
CALIFORNIA
GEORGIA
MINNESOTA
TEXAS
6550 Katella Avenue
Cypress, CA 90630
800 Dubuque Avenue
S. San Francisco,
CA 94080
3878 Ruffin Road
Suite A
San Diego, CA 92123
8655 Roswell Road
Suite 100
Atlanta, GA 30350
7850-12th Avenue South
Airport Business Center
Bloomington, MN 55425
13615 Welch Road
Suite 101
Farmers Branch,
TX 75244
ILLINOIS
OHIO
1709 North Randall Road
Elgin, IL 60123
2236 Waycross Road
Civic Center Plaza
Forest Park, OH 45240
FLORIDA
MASSACHUSETTS
PENNSYLVANIA
3700 North 29th Avenue
Suite 102
Hollywood, FL 33020
60 Glacier Drive,
Suite G
Westwood, MA 02090
2221 Cabot Blvd. West
Suite B
Langhorne, PA 19047
WASHINGTON
20425-84th Avenue
South
Kent, WA 98032
HAWAII
99-859 Iwaiwa Street
Aiea, Hawaii 96701
Phone (808) 488-1996
Fax (808) 486-4369
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infanteria. Km. 9.5 San Gabriel Industrial Park Carolina, Puerto Rico 00985
Phone (787) 750-4300 Fax (787) 768-2910
As of June 2001
32
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Limited Warranty
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation
of America, One Panasonic Way
Secaucus, New Jersey 07094
Panasonic Sales Company,
Division of Matsushita Electric of Puerto Rico, Inc.
AVE. 65 de Infantería, Km. 9.5 San Gabriel
Industrial Park Carolina, Puerto Rico 00985
PANASONIC/QUASAR Video Products
Limited Warranty
Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the
Warrantor”) will repair or replace this product with new or refurbished parts or equivalent product, free of charge, in
the USA or Puerto Rico, in the event of a defect in materials or workmanship as follows (all time periods commence
from the date of the original purchase):
PRODUCT
CAMCORDER
PARTS
ONE (1) YEAR, EXCEPT
CCD IMAGE SENSOR
CCD IMAGE SENSOR
- SIX (6) MONTHS
LABOR
NINETY (90) DAYS
SERVICE
Carry-In or Mail-In
CONTACT NUMBER
1-800-211-PANA(7262)
DVD/VCR DECK ONE (1) YEAR
ONE (1) YEAR, EXCEPT
DIGITAL STILL
CCD IMAGE SENSOR
CAMERA
CCD IMAGE SENSOR
- SIX (6) MONTHS
A/V MIXER
ONE (1) YEAR
NINETY (90) DAYS
NINETY (90) DAYS
Carry-In or Mail-In
1-800-211-PANA(7262)
TV/VCR, TV/DVD ONE (1) YEAR,
EXCEPT CRT
TV/DVD/VCR
COMBINATION CRT - TWO (2) YEARS
NINETY (90) DAYS
NINETY (90) DAYS
CRT - NINETY (90) DAYS
ONE (1) YEAR,
EXCEPT CRT
CRT - TWO (2) YEARS
NINETY (90) DAYS
CRT - NINETY (90) DAYS
TV/HDR
COMBINATION
Carry-In or Mail-In
1-800-272-7033
NINETY (90) DAYS
NINETY (90) DAYS
1-800-211-PANA(7262)
Carry-In or Mail-In
Carry-In: 21” CRT and 1-800-211-PANA(7262)
Smaller
In-Home or Carry-In:
22” CRT and Larger
In-Home or Carry-In 1-888-843-9788
33
For Your Information
Batteries (if included) - New rechargeable batteries in exchange for defective rechargeable batteries for ten (10)
days. Non-rechargeable batteries are not warranted.
Tape (if included) - New video cassette tape in exchange for a defective video cassette tape for five (5) days.
Memory cards (if included) - Exchange defective item for new one for ninety (90) days.
In-home, carry-in or mail-in service, as applicable, in the USA can be obtained during the warranty period by
contacting a Panasonic Services Company (PASC) Factory Servicenter listed in the Servicenter Directory.
Or call toll free contact number listed above, to locate an authorized PASC Servicenter. Carry-in or mail-in service
in Puerto Rico can be obtained during the warranty period by calling the Panasonic Sales Company telephone
number listed in the Servicenter Directory.
This warranty is extended only to the original purchaser. A purchase receipt or other proof of the date of the original
purchase is requires before warranty service is rendered.
This warranty only covers failures due to defects in materials and workmanship, which occur during normal use and
does not cover normal maintenance, including, but not limited to, video and audio head cleaning. The warranty
does not cover damage which occurs in shipment, or failures which are caused by products not supplied by the
warrantor, or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration,
modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of
consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, commercial
use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than
a PASC Factory Servicenter or a PASC authorized Servicenter, or damage that is attributable to acts of God.
LIMITS AND EXCLUSIONS
There are no express warranties except as listed above.
THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING,
WITHOUT LIMITATION, DAMAGE TO RECORDING MEDIA) RESULTING FROM THE USE OF THIS PRODUCTS,
OR ARISING OUT OF ANY BREACH OF THE WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE
LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the
exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so
the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may
also have other rights, which vary, from state to state. If a problem with this product develops during or after the
warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then
write to the Consumer Affairs Department at the Panasonic Consumer Electronics Company address above.
SERVICE CALLS WHICH DO NOT INVOLVE DEFECTIVE MATERIALS OR WORKMANSHIP AS DETERMINED
BY THE WARRANTOR, IN ITS SOLE DISCRETION, ARE NOT COVERED. COSTS OF SUCH SERVICE CALLS
ARE THE RESPONSIBILITY OF THE PURCHASER.
warvid 02/ 12/ 2001
Spanish Quick Use Guide/Guía para rápida consulta
Connexiones/Configurcion Inicial
Conecte por favor todas las conexiones
del cable o de la antena antes de turing
potencia. Conectando el cordon AC de la VCR
en toma de pared iniciara automaticamente la
busqueda de canales y colocacion de tiempo
Conectando
Para Ant./Cable
Conecte Ant./Cable a la entrada de
antena de la TV (VHF/UHF).
Para Sistema Digital de Satelite (DSS)/
Convertidor de cable
Conecte la salida del convertidor de cable la
"VHF/UHF" con el RF cable.
Realizando Configuracion Inicial
1
Tape el cable electrico de la unidad en el
enchufe de pared de la CA. POWER de
la prensa en el telecontrol o la unidad.
La unidad se adelanta y comienzo auto
del canal y del reloj.
CH AUTO SET PROCEEDING
AUTO CLOCK SET
PROCEEDING
Si usa convertidor de
cable, enciendala y
seleccione el Servicio
Publico de Canales de
Television (PBS) en su
horario de uso o tiempo
de su zona. Si utiliza
receptor DSS este debe
de estar apagado.
Ajuste Manual del Reloj
Si el ajuste automático del reloj no se
ha completado, ajuste el reloj
manualmente de la siguiente manera:
1) Presione la tecla ACTION en el
control remoto para visualizar la
pantalla del menú RELOJ.
2) Presione ▲▼ para seleccionar
el mes y para ajustar. De la
misma forma, seleccione y
ajuste la fecha, año, hora y DST
(Hora de Verano).
3) Presione dos veces la tecla
ACTION para poner el RELOJ
en marcha y salir.
Ajustar de nuevo el reloj
1
2
Presione ACTION para exhiba
el menú.
MENU PR I NC I PAL
TV
VCR
IDIOMA
CANAL
REL OJ
SAL I R
ELEG I R :
F I JAR : ACT I ON
3
F I JAR RELOJ
F I JAC I ON AUTOMAT I CA
MANUAL
AJUSTE ZONA HORA : 0
ELEG I R :
F I JAR :
TERM I NAR : ACT I ON
CANCEL : PRESS STOP KEY
2
2 / 6 / 2002 WEDDST
12::ON
00PM
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
AUTO CLOCK SET
I S I NCOMPLETE
PLEASE SET CLOCK BY
PRESS I NG ACT I ON KEY
34
Selecciones se
realizaran
automaticamente cuando
la configuracion termine,
la pantalla siguiente
aparecera.
Si "AUTO CLOCK SET IS
INCOMPLETE" aparece en
pantalla, coloque el tiempo
usando el procedimiento
manual (MANUAL CLOCK
SET), vealo enseguida..
4
F I JAR RELOJ
:
1/ /
VERANO : ACT
ELEG
ES
ELE I R MES
ELEG I R :
F I JAR :
TERM I NAR : ACT I ON
5
Presione
▲▼
para
seleccionar
“RELOJ”.
Presione
ACTION.
Presione
▲▼ para
seleccionar
“MANUAL”
y luego
presione .
Presione
▲▼ y
para
seleccionar
y ajustar la
hora y la
fecha.
Presione ACTION dos veces
para que el reloj comience a
funcionar y salir desde este
modo.
For assistance,
pleasealcall
: 1-800-211-PANA(7262)
or sende-mail
e-mail to
Por
ayuda, llame
: 1-800-211-PANA(7262)
o envie
a : consumerproducts@panasonic.com
Operaciones básicas para la
reproducción
1
2
■
■
■
■
■
■
■
■
Inserte un casete.
• El videograbador combinado se enciende
automáticamente.
Presione PLAY.
• La reproducción comienza
automáticamente si el casete no tiene la
lengüeta para prevención de grabación.
Para encontrar una escena en particular
Búsqueda hacia adelante => Presione FF
Búsqueda hacia atrás => Presione REW
Para ver una imagen fija (congelada) => Presione
PAUSE/SLOW
Para ver en cámara lenta => Mantenga pulsado el
botón PAUSE/SLOW en el modo de imagen fija
Para ver imágenes cuadro a cuadro => Presione
PAUSE/SLOW en el modo de imagen fija
Para parar => Presione STOP
Para rebobinar la cinta => Presione REW
Para hacer avanzar la cinta rápidamente =>
Presione FF
Para expulsar la cinta => Presione EJECT
en el control remoto o STOP/EJECT en el
videograbador combinado
Operaciones básicas para la
grabación
1
2
3
4
Inserte un casete con la lengüeta
para prevención de grabado.
• El videograbador combinado se enciende
automáticamente.
Seleccione el canal.
Presione CH ▲▼ o las teclas
numéricas correspondiente.
Seleccione la velocidad de grabación.
Grabación con temporizador
1
2
3
3:00
2:00
1:30
FECHA
INICIO
PARADA
CA
7 VIE --:-- --:-- -HOY
SLP
-----------------------ELEGIR FECHA DE INICIO
ELEG l R :
F I JAR :
TERM l NAR : PROG / ACTION
Ajuste la fecha de
grabación.
1) Presione ▲▼
para seleccionar.
2) Presione o
para ajustar.
• 1 - 31 = Grabación única
• DIARIO = a la misma hora de lunes a viernes
• SEMANAL = a la misma hora una vez a la
semana
Fecha de hoy
Repita el paso 3 para ajustar:
hora de comienzo, hora de parada, canal
(o LINEA para una fuente exterior), velocidad
(SP, LP, SLP)
4
P
1
2
3
4
FE I N I C PARADA
D I 9 : 00p 12 : 00a
-- -- : -- -- : --- -- : -- -- : --- -- : -- -- : --
CA VEL
08 SP
-- --- --- --
CANCELAR : ADD/DLT
ELEG I R 1-8 :
ENTRAR :
TERM I NAR : PROG / ACT I ON
Termine el
programa.
Presione PROG
(o ACTION.)
Para introducir más programas.
presione ▲▼ y para seleccionar y
ajustar el número de programa en
blanco, y luego repita los pasos 3 y 4.
5
Salga de este modo.
Presione PROG dos veces (o
ACTION.)
• Si está usando un decodificador de TV
cable, asegúrese que se encuentra en el
canal deseado y que la alimentación
queda conectada para grabar con
temporizador.
• El indicador PROG TIMER se enciende
en el videograbador combinado.
35
For Your Information
4:00
TEMPOR l ZADOR
ENCENDIDO AUTOMATICO
• Si ya existe un programa en la memoria,
presione ▲▼ y para seleccionar un número
de programa sin usar.
Comience la grabación.
Presione REC.
■ El videograbador combinado deja
de grabar a una hora prefijada.
(Grabación de un toque)
Presione REC repetidamente para
ajustar la hora de grabación (30 min
- 4 horas.)
Grabación normal 0:30 1:00
Exhiba
TEMPORIZADOR.
1) Presione ▲▼
para seleccionar.
2) Presione para
exhibir.
F I JAR PROGRAMAC I ON
ELEG l R :
F I JAR :
TERM l NAR : PROG
Presione SPEED.
SP = reproducción normal
LP = reproducción larga
SLP = reproducción super larga
• La velocidad seleccionada debe aparecer
en la pantalla.
• Para editar partes no deseadas de una
grabación, presione PAUSE/SLOW para
hacer una pausa durante la grabación.
• No podrá ver otro canal durante la
grabación.
■ Para parar => Presione STOP.
Exhiba FIJAR PROGRAMACION.
Presione PROG.
INDEX
A
B
C
D
E
F
H
I
L
LSQT0605A
N
O
Accessories ................................................ 3
Audio Mute ................................................ 14
Auto Operation Functions ......................... 23
Batteries ....................................................... 3
Before Requesting Service .......................... 31
Before Using ................................................. 3
Blocking Message ....................................... 29
Blue Screen Display .................................... 30
Caption On Mute ......................................... 19
Channel ................................................ 10, 30
Channel Caption .......................................... 26
Clock .......................................................... 10
Closed Caption ........................................... 18
Commercial Skip ......................................... 24
Connections .................................................. 8
Connections, DSS / Cable Box ...................... 8
Connections, Outdoor Antenna ..................... 8
Copy Your Tapes (Dubbing) ....................... 13
DST (Daylight Saving Time) .......................... 4
Eject tape .................................................... 12
Fast Forward .............................................. 12
Forward Search .......................................... 12
Frame by Frame Advance .......................... 12
Front Panel Indicators ................................... 7
Function Display ......................................... 30
Head Cleaning .............................................. 4
Important Safeguards and Precautions ......... 2
Index Search .............................................. 22
Initial Setup for ANT. / Cable Connection ....... 8
Initial Setup for DSS / Cable box Connection ...... 8
Input Mode .................................................. 13
INSTANT ALARM ....................................... 17
Language .................................................... 10
Limited Warranty ......................................... 33
Location of Controls ................................ 6 - 7
NIGHT Mode .............................................. 14
100 Key ...................................................... 14
One Touch Recording ................................. 12
ON-TIMER with Alarm ................................. 16
P
Q
R
S
T
U
V
W
Z
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus,
New Jersey 07094
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phones .................................................. 14
Playback ............................................... 12
Picture Adjustment ................................ 15
Program End Search ............................ 22
Quality Picture ........................................ 4
Rapid Tune ........................................... 14
Rec(ord) ................................................ 12
Record/Playback Speed Settings ........... 4
Remote Control Buttons ......................... 6
Repeat Play .......................................... 24
Reset Language, Channels, Clock ....... 10
Reset unit ................................................ 9
Reverse Search .................................... 12
Rewind .................................................. 12
Secret Code .......................................... 27
Service Center List ............................... 32
Sleep Timer .......................................... 17
Slow Motion .......................................... 12
Spanish Quick Use Guide ..................... 34
Special VCR Features .......................... 25
Specifications .......................................... 4
Still Picture ............................................ 12
STOP .................................................... 12
Tape Erasure Prevention ........................ 3
Tape Position Display ........................... 23
Time Zone Adjust .................................. 11
Timer Program Review, Replace, Clear 21
Timer Recording ................................... 20
Timer Recording Cancellation .............. 21
TV Operation ......................................... 14
TV Timer Features ................................ 16
Unit, Front/Rear view .............................. 7
US MOVIES/TV PROGRAMS Ratings . 29
VCR Lock .............................................. 25
VCR Status & Clock Display ................. 30
V-Chip Control Feature ......................... 27
Warning and Instruction Displays ......... 30
Weak Signal Display ON/OFF .............. 25
Zero Search .......................................... 24
P
Printed in Indonesia
LSQT0605A
M0202-0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising