Panasonic Cell Phone EB-GD52 User manual

Panasonic Cell Phone EB-GD52 User manual
Operating Instructions
Digital Cellular Telephone
EB-GD52
Before operating this equipment please read these instructions completely.
Quick Reference
This Quick Reference guide is intended to enable the user to utilize the most basic
features of the phone instantly without having to search through the extra details
which are incorporated into this manual.
Power On/Off
Press and hold E
Enter Pin Code
Use the keypad to enter the PIN
supplied by your Service Provider,
then press B
Make a Call
Use the keypad to enter the area
code and telephone number, then
press D
Correcting an Error
Press C once to erase the
previous character
Press and hold C to remove all
characters entered
Make Emergency Call
Press 112 D
International Dialling
Press and hold 0, use e to
select the appropriate country
code, then press B
Add Phonebook Entry to SIM
Enter phone number and press
A. Press B, enter name and
press B twice
Dial SIM Phonebook Entry
Press A, then use e to select
the desired number, then press
D
What is My Number ?
Redial Last Number
Press DD
End a Call
Press E to end a call
Answer a Call
Press any key except E or g
Adjust Ear Volume
Press e during a call
Press B25 and the
number of your phone will be
displayed (SIM dependent)
Set Key Guard
Press B three times and the keys
will be locked to avoid accidental
presses
Disable Key Guard
Press B twice (when Free is
displayed) to remove the Key
Guard
Contents
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Fitting the SIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Fitting the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Getting to Know Your Phone . . . . . . . . . . . . . . . . . . . . . . . 3
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Switching the Phone On/Off . . . . . . . . . . . . . . . . . . . . . . . . 6
Making a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Automatic Redial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Ending a Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Answering a Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Earpiece Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . 7
Locking the Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using the PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setting Vibration Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting Ring and Key Volume . . . . . . . . . . . . . . . . . . . . . . . 9
Phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Store a Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Browsing Phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Retrieve a Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Editing Phonebook Entries . . . . . . . . . . . . . . . . . . . . . . . . 11
Grouping Phonebook Entries. . . . . . . . . . . . . . . . . . . . . . . 12
Personal Dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Hot Key Phone Numbers . . . . . . . . . . . . . . . . . . . . . . . . . 13
Service Dial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Review the Phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . 14
My Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Personalising Your Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Add a Start-up Greeting . . . . . . . . . . . . . . . . . . . . . . . . . 15
Displaying Animations . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Changing the Ring Tone . . . . . . . . . . . . . . . . . . . . . . . . . 15
Disabling all Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Selecting Vibration Alert Type . . . . . . . . . . . . . . . . . . . . . . 16
Changing the Language . . . . . . . . . . . . . . . . . . . . . . . . . 16
Restoring the Default Phone Settings . . . . . . . . . . . . . . . . . . 16
Phone Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using Key Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Changing the Security Codes . . . . . . . . . . . . . . . . . . . . . . 17
Restricting Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Calculator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Currency Convertor. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Short Text Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Setting the Phone for Text Messages . . . . . . . . . . . . . . . . . . 23
Sending a Text Message . . . . . . . . . . . . . . . . . . . . . . . . . 23
Receiving Text Messages . . .
Message Options . . . . . . . .
Using Pre-defined Messages. .
Manage Messages Lists . . . .
Message Parameters. . . . . .
Cell Broadcasts. . . . . . . . .
Call Information . . . . . . . . . . . .
Recent Numbers . . . . . . . .
Call Duration . . . . . . . . . .
Call Charges . . . . . . . . . .
Call Identification . . . . . . . .
Advanced Operation . . . . . . . . .
Diverting Calls . . . . . . . . .
Holding Calls and Call Waiting .
Call Transfer . . . . . . . . . .
Multi-party Calls . . . . . . . .
Changing to a New Network . .
Additional Features . . . . . . . . . .
Desktop Handsfree . . . . . . .
DTMF Tones . . . . . . . . . .
Note Pad . . . . . . . . . . . .
Accessory Related Features . .
Text Entry . . . . . . . . . . . . . . .
Menu Structure . . . . . . . . . . . .
Trouble Shooting . . . . . . . . . . .
Important Error Messages . . .
Important Information . . . . . . . .
Safety Considerations . . . . .
Care and Maintenance . . . . . . . .
Glossary of Terms . . . . . . . . . .
Specifications . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
24
24
24
25
26
26
28
28
28
29
29
30
30
30
31
31
33
34
34
34
35
35
36
38
39
40
42
42
44
45
46
Getting Started
Getting Started
Thank you for purchasing this Panasonic digital cellular phone. This phone is
designed to operate on the Global System for Mobile Communications (GSM),
GSM900 or GSM1800. Ensure the battery is fully charged before use.
Before operating this phone please read the “Important Information” section see page 42.
These operating instructions detail use of the equipment contained in the Main Kit.
Some services detailed herein are network dependent or may only be available on a
subscription basis. Some functions are SIM dependent. For more information contact
your Service Provider.
Fitting the SIM
The SIM is inserted into the back of the
phone underneath the battery.
First, remove the battery cover by
pushing the cover downwards - see
Œ
“Removing the Battery”.
Place the SIM in the recess at the rear
of the phone (1) ensuring the bevelled
corner is positioned in the top right
corner. Slide the SIM to the left (2) using

light pressure until it is located under the
lugs and the SIM retaining clip has clicked into position (3).
Ž
Removing the SIM
Ensure the SIM retaining clip is pressed
down (1) and while holding this down
slide the SIM to the right (2). Once clear
of the lugs the SIM can be lifted out of
the recess.
Œ

1
Getting Started
Fitting the Battery
Œ

Ž

Fit a fully charged battery pack. If the
battery pack is not fully charged then it
must be charged as described in the
“Charging the Battery” section.
First, remove the battery cover by
pressing where indicated and sliding
the cover downwards (1). Ensure that
the battery locking mechanism is
located to the left, then insert the top of
battery (label uppermost) into the
battery recess (2). Place the base of the
battery into the phone and push the
sliding mechanism to the right locking
the battery into place (3). Replace the
battery cover, sliding upwards until it clicks into position (4).
Removing the Battery
First, remove the battery cover by
pressing where indicated and sliding
the cover downwards (1).
Push the sliding mechanism to the left
to release the battery (2). The battery
can now be removed from the phone
(3).
Œ

Ž
Charging the Battery
Connecting the AC
Adaptor

Œ
The battery pack must be attached to
the phone before the AC Adaptor is
connected. Insert the AC Adaptor plug
into the base of the phone (1).
Note: DO NOT force the connector as
this may damage the phone and/or the
AC Adaptor.
Connect the AC Adaptor to the mains power supply (2). Indicator will light and
charging starts.
2
Getting Started
Operation of Battery Level Indicator
While charging
Charging complete
Telephone on
K
H
Telephone off
K
Indicator off
When charging is complete remove the AC Adaptor.
Disconnecting the AC Adaptor
Disconnect the AC Adaptor from the
mains power supply (1).
Squeeze together the two buttons on
the plug of the AC Adaptor (2) and while
maintaining pressure extract the plug
from the base of the phone (3).


Œ
Ž
Low Battery Warning
When the battery power is low a warning tone will sound and a
blinking LOW BATTERY message will be displayed. If this
occurs during conversation finish your call immediately. The
power will be automatically shut off shortly after the warning
tone. Fully charge the battery pack or replace it with a fully
charged one.
Getting to Know Your Phone
Location of Controls
Antenna
Incoming/Charging
Indicator
Earpiece
Earphone/Microphone Socket
External Connector
P
A
B
D
C
1
4 2 E
7 5 3
* 8 6
0 9
#
Display
Microphone
3
Getting Started
g
B
A
P
D
C
E
Navigation key – pressing up/down/left/right scrolls through options in the
main area of the display. Pressing left/right scrolls through options in the
option area of the display
Select key – selects an option in the option area of the display
accesses Phonebook or switches character types
provides instant access to one phone number (Personal Dial)
makes a call or recalls recently dialled phone numbers
clears the last digit entered, clears all digits when pressed and held or
returns to the previous display
ends a call or switches the phone on/off when pressed and held
Digit keys 0 to 9, * and # – the # key will switch on and
off vibration alert
The Menu System
The menu system provides the means for accessing all the functions which do not
have their own dedicated buttons on the keypad.
The menu functions can be selected using a combination of the Navigation key g
and the menu Select key B.
During a call a restricted menu will be available.
Shortcuts
In addition, once you are familiar with the layout of the menu you can use the keypad
to enter the Menu Number to quickly obtain the required function. For example,
pressing B to enter the menu and then 52 will take you directly to the menu
for changing the ring tone. Examples in these instructions use the shortcuts to gain
access to the relevant functions or to the sub-menu under which other functions are
located.
Display Icons
Status Icons
Main Display Area
Option Area
Information Area
Navigation Prompt
Following some operations the display will automatically clear after three seconds or
after pressing any key.
4
Getting Started
Status Icons
The status icons are displayed according to the currently activated functions. The
Antenna, Signal and Battery icons are always displayed when the handset is
switched on and connected to a network.
Y
lights when you are registered to a non-home network - roaming
t
lights when call divert is enabled
]
lights when vibration alert is enabled
[
lights when all tones or ring volume is off
N
blinks when an unread message is stored or lights when message area is
full
O
lights when phone lock is enabled
S
indicates that it is possible to make emergency calls
T
indicates the received signal strength: \ - weak signal, T - strong
signal
H
indicates the battery level: H - full, G (blinking) - low battery
Information Area
This area is used to indicate the current top level menu, the sub-menu number, text
entry mode, Phonebook source, Phonebook location number, or the alarm set icon
depending on the current mode of operation.
?
indicates alarm is set
>
indicates current Phonebook entry is sourced from Mobile Phonebook
<
indicates current Phonebook entry is sourced from SIM Phonebook
Navigation Prompt
p
This area indicates the available directions in which the Navigation Key
can be pressed according to the current mode of operation.
Option Area
The Option Area displays the options which can be selected by pressing the Select
key (B).
5
Basic Operation
Basic Operation
Switching the Phone On/Off
To switch the phone on or off.
Press and hold E to switch power on
A greeting animation will be displayed and then the phone will
go into Idle mode.
Press and hold E to switch power off
Making a Call
Ensure that the phone is switched on, the network operator
logo is displayed and the signal strength meter shows network
coverage is available in the current area.
1 Enter area code and phone number
2 Press D
International Dialling
Using the automatic international access code (+) you will be able to dial international
numbers without having to know the code for the international exchange.
If the international number is known then it can be entered in the normal fashion
followed by the area code and phone number.
1 Press and hold 0 until + is displayed
2 Press e to cycle through the abbreviated international
names and press B to select the required code
3 Enter area code and phone number
4 Press D
Note: Many countries include an initial “0” in the area code. This should, in most
cases, be left out when dialling international numbers. If you have difficulties making
international calls, contact your Service Provider.
Emergency Calls
To make an emergency call the antenna symbol (S) must be present.
Enter 112 D or press B when SOS is displayed in the option area
6
Basic Operation
Automatic Redial
When a call is unsuccessful the phone may ask if you want to
redial the phone number again automatically.
Press B when Ok is displayed in the option area and
the display will countdown in seconds to the next redial.
To stop redialling, press B when Cancel is displayed in
the option area or press C.
When a call is connected a beep will be emitted.
If a call is repeatedly unsuccessful you will not be able to automatically redial the
phone number. In this case you must redial the phone number manually.
Ending a Call
Press E
Answering a Call
To receive a call the phone must be switched on and the signal strength meter must
be displayed.
Press any key except E or g
Press E to reject the call
If a call is not answered, or is rejected, the number of unanswered calls will be
displayed.
Press any key to clear the display
Caller Identification
This feature allows you to identify incoming calls and accept
or reject them. The caller’s phone number, and name if stored
in Phonebook, will be displayed.
Note: Caller Identification may not always be available.
Earpiece Volume Control
The volume level may be adjusted during a call:
Press a to decrease the volume
Press b to increase the volume
Volume control for Personal Handsfree accessory is adjusted
in the same manner.
7
Basic Operation
Locking the Phone
With the Phone Lock enabled you will be restricted to answer incoming calls and
make emergency calls only. The Phone Lock Code is factory set to “0000”.
1 From Idle mode press B 81 to enter the Phone
Lock menu
2 Enter the 4-digit code and press B
The phone will be locked and the lock icon (O) will be
displayed.
Unlocking the Phone
To restore normal operation, enter your Lock Code and press B. The lock icon will
be removed from the display. However, once you turn the phone off and on again you
will need to re-enter the Lock Code, and when the correct code has been entered Ok
will be displayed. Press B.
Disabling Phone Lock
1 From Idle mode press B 8 to enter the Security menu.
2 Press f until Disable is displayed in the option area
3 Press B
4 Enter the Lock Code and press B
Using the PIN
The PIN (Personal Identification Number) protects your SIM against unauthorized
use. If you enable the PIN, every time the phone is turned on you will be prompted to
enter the PIN.
The PIN2 controls security for the Fixed Dial Store and Call Charge metering.
Enabling/Disabling the PIN
1 From Idle mode press B 83 to enter the PIN menu
2 Press B to enable/disable the PIN
3 Enter PIN number B
8
Basic Operation
Setting Vibration Alert
When vibration alert is switched on the phone will vibrate when a call is received.
Switching on vibration alert will silence the ring volume. However, when the ring
volume is adjusted after the vibration alert is switched on, the phone will ring and
vibrate when a call is received.
From Idle mode:
Press and hold # to switch on or off. When switched
on, the phone will vibrate briefly.
Setting Ring and Key
Volume
Changing either the ring volume and key volume is done in the same manner. If you
increase the ring volume above maximum it will set an escalating ring tone. If you turn
the ring volume off, the silent indicator icon ([) will be displayed.
1 From Idle mode press B 52 to enter the Tones menu
2 Use e to select Ring Volume or Key Volume and press B
3 Use e to set the volume level and press B
9
Phonebook
Phonebook
Phone numbers can be stored in two locations. You can store numbers in the SIM
Phonebook (therefore the number of locations, length of name and number of phone
numbers are SIM dependant). Alternatively you can store phone numbers in the
Mobile Phonebook, this means that if you change the SIM the numbers in the phone
are not lost.
The Mobile Phonebook has the advantage that you can group your phonebook
entries together.
Store a Number
To Store a Number in the SIM Phonebook
1 From Idle mode enter the phone number and press A
2 Press B to select the SIM Phonebook
3 Enter the name – see “Text Entry” page 36, and press
a
4 Confirm phone number and press B
5 Enter location number and press B
You can choose not to enter a location number and the entry will be placed in the next
available location. Simply press B when Any is displayed in the option area.
To Store a Number in the Mobile Phonebook
1 From Idle mode enter the phone number and press A
2 Use a to select the Mobile Phonebook and press B
3 Enter the name - see “Text Entry” page 36, and press a
4 Confirm phone number and press B
5 Use e to select a group - see “Grouping Phonebook Entries” page 12 - into
which to place the entry and press B
6 Enter location number and press B
You can choose not to enter a location number and the entry will be placed in the next
available location. Simply press B when Any is displayed in the option area.
Overwrite Protection
If a location is occupied you will be prompted to confirm that you wish to overwrite the
current information.
Press B to overwrite the selected location
Press C to choose another location number
10
Phonebook
Browsing Phonebook
You can search the Phonebook by either Name or Location. The default setting for
browsing is by name. When browsing by name pressing a lettered key will take you to
the first entry starting with that letter.
1 From Idle mode press B 2 to enter the Phonebook menu
2 Use f to toggle between Names or Loc’ns display mode and press B
3 Use e to select the Phonebook you wish to browse and press B
Retrieve a Number
From Idle mode:
1 Press A
2 Use e to browse through the Phonebook
Once you have selected a phone number or name, there are a number of actions that
you can perform. To dial the selected number press D.
Note: The Phonebook you last viewed will be the default when you next press A. To
change the default, use the Phonebook menu to select a particular phonebook.
Speed Dial a Number Stored in SIM Phonebook
1 Enter location number – leading zeros may be left out
2 Press #
3 Press D
Editing Phonebook Entries
You can Detail, View, Recall, Edit, Delete or Create in the Phonebook. To access any
of these functions you follow the same procedure. With a phone number or name
displayed:
1 Use f to cycle through Detail, View, Recall, Edit, Delete or Create
2 Press B to select an option
Detail
Displays each element of the selected Phonebook entry. Use e to display the
next/previous element of the entry. Each element may be edited - use f until Edit is
displayed in the option area and press B.
View
Displays an individual name and phone number in the names list.
11
Phonebook
Recall
Displays the phone number, enabling you to either change it or call the number.
Edit
Displays the entry allowing you to make changes as required. Press B to save any
changes.
Delete
Deletes the entry from the Phonebook.
Create
Creates a new entry in the Phonebook
Grouping Phonebook Entries
The ability to group phonebook entries together is an extra function of the Mobile
Phonebook.
Retrieving a Number from a Group
Groups are used to collect together types of Phonebook entries, for example
business and personal. Each group can be suitably titled for quick access to the
entries contained within.
1 From Idle mode press B 23 to enter the Group Settings menu
2 Use e to select the group and press B
3 Use e to select the entry required and press B to recall the number.
Retitling Group Names
1 From Idle mode press B 23 to enter the Group Settings menu
2 Use e to select the group
3 Use f until Edit is displayed in the option area and press B
4 Clear the current title and re-enter - see “Text Entry” page 36
5 Press B
12
Phonebook
Personal Dial
The P key can be defined to recall your favourite phone number in preparation for
initiating a call.
Setting the Personal Dial Number
1 From Idle mode press B 27 to enter the Personal Dial menu
2 Enter the name - see “Text Entry” page 36, and press a
3 Enter the phone number and press B
Using Personal Dial
From Idle mode:
Press P to recall the number, then press D to initiate a call
Hot Key Phone Numbers
It is possible to dial phone numbers from the Phonebook or Service Dial part of
Phonebook very quickly. Some Hot Key Phone numbers may be reserved by the
Service Provider, for example the first three Hot Key Phone numbers may be linked
to Service Dial (network dependent).
1 Press and hold a Digit key 1 to 9
2 Press D
Setting the Hot Key Dial Source
1 From Idle mode press B 26 to enter the Hot Key Dial menu
2 Use e to select SIM Phonebook or Mobile Phonebook and press B
Service Dial Numbers
Your Service Provider may program some special phone numbers into your SIM
(network dependent). It is not possible to modify the Service Dial numbers.
1 Press and hold A
2 Press e to browse through the Service Dial list of phone numbers
The phone number pointed to can only be recalled or dialled.
13
Phonebook
Review the Phonebook
The Review function in the Phonebook menu shows how many locations are
available in the Phonebook.
1 From Idle mode press B 24 to enter the Review menu
2 Use e to select SIM Phonebook or Mobile Phonebook and press B
A summary of the selected Phonebook will be displayed.
3 Use e to gain a detailed view of the Phonebook locations. Occupied locations
are shown with “w”.
My Numbers
My Numbers is a convenient part of Phonebook where your voice, fax and data
phone number(s) can be stored and viewed. This function is SIM dependent.
1 From Idle mode press B 25 to display the number
2 If more than one number is available then use e to cycle through the listed
numbers
14
Personalising Your Phone
Personalising Your Phone
Add a Start-up Greeting
A personalised greeting can be programmed for when the phone is switched on.
1 From Idle mode press B 531 to enter the Greeting menu
2 Use the text entry facility to add your greeting and press B - see “Text Entry”
page 36
Displaying Animations
Animations can be displayed when the phone is switched on.
1 From Idle mode press B 533 to enter the
Animation menu
2 Use e to cycle through the animated themes available
3 Press B to select either the desired theme, or disable the animation
Changing the Ring Tone
The ring tones of the phone can be changed to one of many pre-defined sounds or to
a voice ringer (a voice recording used as a ring tone).
Setting up a Pre-defined Ring Tone
You can choose from a selection of tones and melodies.
1 From Idle mode press B 523 to enter the
Ring Type menu
2 Use e to cycle through the ring types
3 Press B to select the desired ring tone
Recording a Voice Ringer
1 From Idle mode press B 524 to enter the Voice Ringer menu
2 Press 1 and start speaking into the microphone to record your voice. The
recording will stop automatically after 5 seconds, or before if B is pressed.
3 To playback the recording press 2
Disabling all Tones
1 From Idle mode press B 521 to enter the All Tones menu
2 Press B to disable all tones and the silent indicator icon ([) will be displayed.
Repeat the process to enable all tones.
15
Personalising Your Phone
Selecting Vibration Alert Type
The vibration alert facility may be set to vibrate continuously or intermittently.
1 From Idle mode press B 54 to enter the Vibration Alert menu
2 Use e to select the type of vibration desired and press B
Once recording is complete for a second time the display will indicate if the recording
was successful or not.
Changing the Language
It is possible to change the language that the phone uses for either the display
messages and/or for text entry.
1 From Idle mode press B 51 to enter the Language menu
2 Use e to select DisplayLanguage or Tegic Language (text entry) that you
wish to change and press B
3 Use e to select the desired language and press B
Restoring the Default Phone Settings
Any personal settings can be returned to their factory default, with the exceptions of
the Phone Lock code and the Language.
1 From Idle mode press B 57 to enter the Defaults menu
2 Press B to restore the default settings
16
Phone Security
Phone Security
The phone features a number of security functions that protect against unauthorized
use, and enable you to restrict access to certain features - see “Using the PIN” page
8. It is recommended that you memorize your security codes. If you need to make a
note of your security codes, never write them in a way that they can be recognized by
another person. If you forget them contact your dealer for the Phone Lock Code or
your Service Provider for PIN and PIN2.
Using Key Guard
The Key Guard function is used to prevent any keys from
being accidentally pressed e.g. when the phone is being
carried.
From Idle mode press B three times to enable Key
Guard
When a call is received Key Guard will be disabled temporarily, allowing you to press
any key to answer the call. Emergency calls can still be made.
Disabling Key Guard
When Free is displayed in the option area press B twice
Changing the Security Codes
1 From Idle mode press B 8 to enter the Security menu
2 Use e to select Phone Lock, PIN or PIN2
3 Use f until Change is displayed in the option area and press B
4 Enter the current code and press B
5 Enter the new code and press B
6 Verify the new code and press B
17
Phone Security
Restricting Calls
Call Barring
The Call Bar function is used to restrict certain outgoing and/or incoming calls. Call
Bar is controlled by a security password that is supplied by your Service Provider.
When updating or checking the status of Call Bar the phone must be registered with a
network. Different Call Bar restrictions can be used for voice, fax and data calls. Any
combination of call restrictions can be set.
1 From Idle mode press B 82 to enter the Call Bar menu
2 Use e to select Bar Voice, Bar Fax or Bar Data and press B
3 Use e to the select level of call barring that you wish to apply and press B
4 Enter Call Bar password and press B
Barred Dialling
The Barred Dial function enables you to bar all phone numbers pre-programmed in
the SIM from being dialled on the phone. To use this function PIN2 is required.
From Idle mode press B 86 and press B to enable Barred Dial ,
enter PIN2 and press B
Fixed Dial
The Fixed Dial Store is part of Phonebook, but with additional security. When the
security feature Fixed Dial is enabled it is only possible to make calls with phone
numbers that are in the Fixed Dial Store.
When Fixed Dial is enabled any manually dialled phone numbers must match a
phone number in the Fixed Dial Store.
To store, edit or delete a phone number in the Fixed Dial Store the Fixed Dial
function must be enabled. With Fixed Dial enabled, all phone numbers can be
added, edited or deleted as normal, but you will be prompted for PIN2.
“Wild” Numbers
Wild numbers are spaces that can be stored in a phone number. The “wild” numbers
must be filled before the phone number is dialled. Used in conjunction with Fixed Dial
calls can be restricted, for example, to a specific area by storing the area code of a
phone and when recalled the remainder can be added. The “wild” numbers can be
anywhere within a stored phone number.
1 Press and hold 0 until _ is displayed to enter a wild
number
2 When the phone number is recalled pressing a numeric
key will fill in a “wild” number.
18
Applications
Applications
Clock
This phone incorporates a clock with date/time, an alarm and a power on/off feature.
Initially Setting the Home Time
1 From Idle mode press B 411 to enter the
Clock Set menu and press B
2 Enter the digits for the date in the format day/month/year
and press B
3 Enter the digits for the time using 24 hour clock and press
B
Setting the Clock Format
1 From Idle mode press B 412 to enter the Clock Format menu
2 Press e to cycle through the different clock and/or date formats
3 Press B to select the desired clock display type
Altering the Time/Date
1
2
3
4
5
6
From Idle mode press B 411 to enter the Clock Set menu
Press and hold C to remove the current date
Enter the digits in the format day/month/year
Press B to accept the date
Press and hold C to remove the current time
Enter the digits using 24 hour clock and press B
Setting the Alarm
If you have not already set the clock, you will be prompted to do so prior to setting the
alarm.
There are four separate alarms, each of which may be set independently.
1 From Idle mode press B 413 to enter the
Alarm Set menu and press B
2 Use e to select the alarm to be set and press B
3 Enter the digits for the time and press B
4 Use e to select the frequency of the alarm and press
B
5 Use e to select the ring type and press B
Once the alarm has been set, ? will be displayed in the information area when the
phone is in Idle mode.
19
Applications
Muting the Alarm
When the set time is reached the alarm will sound and the display will flash with an
alarm message. The alarm will sound for 30 seconds. If the alarm is due during a call,
it will activate vibration alert.
To end the alarm:
Press any key
Disabling the Alarm
1 From Idle mode press B 413 to enter the Alarm Set menu and
press B
2 Use e to select the alarm to be disabled and press B twice
3 Use e until Disabled is displayed and press B
Once disabled, following the same procedure will re-enable the alarm.
Adjusting the Alarm Time
1 From Idle mode press B 413 to enter the Alarm Set menu and
press B
2 Use e to select the alarm to be adjusted and press B
3 Press and hold C to remove the current alarm time
4 Enter the digits for the time and press B
5 Press e to select the frequency of the alarm and press B
6 Use e to select the ring type and press B
Setting a Power On/Off Time
You can set your phone to turn itself on or off automatically at a specified time using
the Power On/Off feature. The procedure for setting/adjusting the Power On/Off
automatically is similar to that for setting the time on the clock. For either setting or
adjusting the time you need to select Power On Time or Power Off Time in the
Clock Function menu.
Caution: Ensure that the setting of the Power On function will not contravene any
regulations whereby it may automatically power on when in an aircraft or medical
facility etc. - see “Important Information” page 42.
20
Applications
Calculator
The four function calculator will enable you to perform simple arithmetic calculations
(addition/subtraction/multiplication and division).
1 From Idle mode press B 42 to enter the Calculator menu
2 Enter a number (maximum 10 digits) and it will be displayed on the lower line
3 Use g to select the arithmetic operation you wish to
perform (b to multiply, c to add, a to divide, d to
subtract)
4 Enter a number (maximum 10 digits) and it will be
displayed next to the operation symbol
5 If you use g to select another arithmetic operation to perform, an intermediate
calculation will be performed and the result displayed on the upper line
6 Press B to complete the calculation when = is displayed in the option area
Note: Press and hold 1 to add a decimal point.
Currency Convertor
The currency convertor enables you to convert from/to a home currency using a
conversion rate that you enter.
From Idle mode press B 43 to enter the Currency menu
Entering an Initial Conversion Rate
1 Press B
2 Enter a country code for the home currency (up to 3
characters) and press B
3 Enter a country code for the foreign currency (up to 3
characters) and press B
4 Enter the currency conversion rate and press B
Note: Press and hold 1 to add a decimal point.
Converting a Value
1 Check the conversion rate is the one you require and press B
2 Enter the value to be converted and press B
The country code and currency rate will be retained in the phone once entered. The
next time you use the convertor you can edit the conversion rate/country codes while
in the Currency/Rate display. Use f until Edit is displayed in the option area and
press B.
21
Applications
Swapping the Currency Conversion
When you have accepted the conversion rate and are ready to enter the value to be
converted, you can swap the currencies to convert from the foreign currency into the
home currency.
1 Use f until Swap is displayed in the option area and press B
2 Enter the value for conversion and press B
22
Short Text Messages
Short Text Messages
You can receive, display, edit and/or send short text messages, of up to 160
characters to mobile phones on the same network or any network that has a roaming
agreement.
Setting the Phone for Text Messages
Before you can send a message you must enter the Message Centre number into
Parameters (your Service Provider will supply the Message Centre number).
The Message Centre number may have been preprogrammed, on your SIM card.
Setting the Message Centre Number
1 From Idle mode press B 363 to enter the Message Centre menu
and press B
2 Enter message centre number in international dial format – see “International
Dialling” page 6
Sending a Text Message
1 From Idle mode press B 33 to enter the Create
menu and press B
2 Enter the message (up to 160 characters) – see “Text
Entry” page 36 and press B
You will be prompted if you wish to send the message, if you
do not wish to send the message press C, the message will be stored.
3 Press B and enter the destination phone number (or recall a number from the
Phonebook) - see “Retrieve a Number” page 11 and press B
4 Press B
5 You may be asked if you wish to have delivery confirmation, if you want
confirmation press B. If you do not, use f until No is displayed in the option
area, then press B
The default setting for delivery confirmation can be enabled/disabled using the
Report parameter in the Short Message menu.
6 Use e to select a melody type, if required, and press B
23
Short Text Messages
Receiving Text Messages
When a Short Text Message is sent to your phone the message indicator (N) will
blink in the display, with an audible tone or vibration. This indicates that a new
message has been received.
When Read is displayed in the option area press B to read
the message. Use g to navigate through the message and
to identify the sender of the message.
Note: If the message indicator is displayed constantly (does
not blink) this indicates that the message area is full and you
will need to delete old messages in order to be able to receive new messages in the
future.
Message Options
Reply to a Message
When you have received and read a message you may wish to reply to the sender.
This is the default setting in the option area and pressing B will allow you to create a
reply message.
Delete a Message
While reading a message use f until Delete is displayed in the option area. Press
B twice to delete the message. To enable the auto-deletion of messages - see
“Message Parameters” page 26.
Edit a message
While reading a message use f until Edit is displayed in the option area. Press B
and make any amendments. Pressing B will give you the option to send the edited
message - see “Sending a Short Text Message” page 23. Press C if you do not wish
to send the message and it will be stored in the Send List.
Using Pre-defined Messages
Pre-defined messages can be sent immediately or they can be used as a basis for a
longer message and edited accordingly.
1 From Idle mode press B 33 to enter the Create menu
2 Use e to point to the pre-defined message you wish to use and press B
3 Use g to navigate through the message and add any extra text – see “Text
Entry” page 36
When complete the message can be sent - see “Sending a Text Message” page 23
24
Short Text Messages
User Defined Message
Creating a User Defined Message
It is possible to create a user defined message which, once generated, can be used
as any other pre-defined message.
From Idle mode press B 34. Edit the message as required and press
B.
Selecting the User Defined Message
From Idle mode press B 33
The user defined message will be displayed at the top of the list of pre-defined
messages.
Use a until the s prompt is adjacent to the message and press B.
Changing the Pre-defined Message Language
With the pre-defined message highlighted:
1 Use f to select Lang in the option area and press B
2 Use e to select a language and press B
3 Use f until Select is displayed in the option area and press B twice to send
the message
Manage Messages Lists
All messages, whether sent or received, will be stored on the SIM until they are
deleted. Selecting a stored message allows it to be replied to, edited or deleted.
Receive List
Messages received will be stored in the Receive List. A blinking “•” indicates an
unread message.
When reading a message the sender’s information is displayed below the text
indicating the time the message was sent and the message centre number. Pressing
B allows you to reply to the message.
Send List
When a message has been sent or edited it will be stored in the Send List.
Review
Review allows you to check usage of the message area.
25
Short Text Messages
Message Parameters
From Idle mode press B 36 to enter the Parameters menu. The
following parameters can be set:
Auto Delete
When set will erase messages automatically:
Received Read - will overwrite the oldest read message
Received Any - will overwrite the oldest message even though it may not have been
read.
Lifetime
This is the duration that your message is stored at the Message Centre. Delivery
attempts will be repeated until the message has been delivered or the Lifetime
expires.
Message Centre
Allows the Message Centre phone number to be edited - see “Setting the Phone for
Short Text Messages” page 23.
Report
When your message has been delivered a confirmation will be received if Report is
set to Yes.
Protocol
The Message Centre may be able to convert the message to the format specified by
the selected protocol.
Cell Broadcasts
Cell broadcasts are general information that is sent to your phone by a network
operator. The information can include topics like local traffic reports, weather etc.
Setting Broadcast Topics
You need to specify the topic(s) of information that you wish to receive as broadcasts
before you can receive them.
1 From Idle mode press B 373 to enter the Topics menu
2 When Insert is displayed in the option area press B
3 Use e to cycle through the available topics and press B to insert the
currently displayed topic into your broadcast list
26
Short Text Messages
Enabling/Disabling Broadcasts
1 From Idle mode press B 371 to enter the Receive menu
2 Press B
Once enabled, following the same procedure will disable broadcasts.
Message List
This is a store for the last received broadcast messages. Messages can be deleted
from here.
Language
The Language in which broadcast messages are displayed can be changed
(network dependent).
27
Call Information
Call Information
Recent Numbers
Recently dialled phone numbers will be stored in Last Dialled.
If Caller Identification is available the caller’s phone number for an answered call will
be stored in Answered and an unanswered call will be stored in Unanswered.
If Caller Identification is not available then calls will still be stored but will have the
date and time attributed to them.
When the store is full the next phone number will overwrite the oldest.
1 Press D
2 Use e to select Last Dialled, Answered or Unanswered and press B
3 Use e to select the phone number (or name) you wish
to redial and press D
You can edit or delete the phone number before dialling – see
“Editing Phonebook Entries” page 11.
If you wish to store the selected number in Phonebook, press
A while the number is displayed – see “Store a Number” page 10.
Calling the Last Dialled Number
To redial your last called phone number press D D
Returning an Unanswered Call
When the display shows that you have received calls but not answered them.
1 Press B
2 The last caller’s phone number will be displayed if it is available
3 Press e to select the phone number you wish to dial
4 Press D
Call Duration
1 From Idle mode press B 6 to enter the Call Service menu
2 Use e to select one of the functions described below, and press B
The Last Call function will display the duration and call charge, if available, of the last
call during Idle mode or the current call during a call. Times are indicated as: hours
(0-99), minutes (0-59), seconds (0-59) - HH:MM:SS.
The All Calls function displays the accumulated duration and call charge, if available,
of incoming and outgoing calls. The lock code or PIN2 is required to reset the timer
and call charge.
28
Call Information
Call Charges
To maintain control over the cost of calls that are made, the phone can be set to
restrict use to a finite number of units overall.
Setting the Unit Price
Firstly, a price per unit must be entered. This is the cost that the Service Provider
charges for one unit of call time.
1 From Idle mode press B 662 to enter the Price/Unit menu
2 Press B to edit the values
At this point you will be asked to enter your PIN2.
3 Enter a currency unit (up to three characters) and press B
4 Enter a price and press B
Setting the Maximum Unit Level
1 From Idle mode press B 663 to enter the Max Cost menu
2 Press B to edit the values
At this point you will be asked to enter your PIN2.
3 Enter a value (number of units) which is to be the maximum permitted, and the
corresponding cost will be displayed
4 Press B to accept
Note: The duration of one unit may vary during the day, peak and off-peak times.
Therefore, the call charge can be calculated accordingly. However, call charge
information may not give an accurate reflection of the tariffs charged by your Service
Provider.
Setting a Warning Level
A warning can be set as an indication that the maximum cost is about to be reached.
1 From Idle mode press B 664 to enter the Warning at menu
2 Press B to edit the value
3 Enter a value (in units) at which time you would like the warning to sound and
press B
Call Identification
In the Call Service menu, the Caller’s ID and Withhold ID functions allow you to
check the status of whether a Caller’s Identification is sent or can be received.
Note: When checking the status the phone must be registered with a network.
29
Advanced Operation
Advanced Operation
Diverting Calls
Voice, fax and data calls can be diverted using different circumstances and to
different numbers. For example you may wish voice calls to be diverted to Voicemail
in the event that the phone is switched off.
1 From Idle mode press B 7 to enter the Call Divert menu
2 Use e to select the type of calls to divert and press B
3 Use e to select the circumstances to initiate the divert and press B
4 Enter phone number to divert to and press B
When a divert situation is enabled the divert icon (t) is displayed.
When updating or checking the status of Call Divert the phone must be registered
with a network.
Holding Calls and Call Waiting
Holding/Resuming a Call
1 Press B when Hold is displayed in the option area
2 Press B when Resume is displayed in the option area
Making a Second Call
1 Enter phone number (or recall from Phonebook – see “Retrieve a Number” page
11)
2 Press D
The first call will be placed on hold.
Receiving a Second Call
A second call can be received, if Call waiting is switched on. This is enabled from the
Call Service menu. It is not possible to have more than one fax or data call. All voice
calls must be ended before you can make or receive a fax or data call.
Accept a Second Call
Press B when Accept is displayed in the option area
The current call will be placed on hold.
Reject a Second Call
1 Press f to display Reject in the option area
2 Press B
30
Advanced Operation
End Current Call and Receive Second Call
1 Press E with a waiting call
2 Press any key except E or g
Operation During Two Calls
Swapping Between Calls
The ! prompt indicates the current call
Press B when Swap is displayed in the option area
End Current Call
1 Press f to display End in the option area
2 Press B
The held call will remain held.
End Both Calls
Press E
Call Transfer
With two calls connected, Call Transfer enables you to connect them together ending
your connection, leaving the other parties to talk together without you.
When you have two calls:
1 Press f to display Trans. in the option area
2 Press B
The two calls will be connected to each other and your call will be ended.
Note: Two call transfer cannot be utilized while in Multi-party mode.
Multi-party Calls
A Multi-party call enables three to five people to be in conversation at the same time.
It is possible to swap between a Multi-party call and another call in the same way as
with two separate calls.
Enabling Multi-party
With two calls connected (one active, one on hold):
1 Press f to display Merge in the option area
2 Press B
A Multi-party call has been enabled, all three people will be able to talk to each other.
31
Advanced Operation
Adding to Multi-party
You can add to the Multi-party call (up to a maximum of five). Either by making a call
or accepting an incoming call. The call can then be merged into the Multi-party.
Note: When making a call or accepting an incoming call the Multi-party call will be
placed on hold. The callers in the Multi-party call can continue to communicate with
each other while on hold.
Splitting a Multi-party
You can select an individual from the Multi-party and remove their connection. This
enables you to talk privately without the participation of the rest of the Multi-party.
During a Multi-party call:
1 Use f until Option is displayed in the option area and press B
2 Press e to select a caller in the Multi-party
3 Press f to display Split in the option area
4 Press B
The selected caller will be split from the Multi-party call and the Multi-party call will be
placed on hold (the remaining Multi-party call callers can still communicate).
Ending Multi-party Calls
You can either select an individual in the Multi-party and end the call or end the entire
Multi-party call. If a call is held, or an other call is incoming then an individual call
cannot be ended.
Ending a Single Connection
During a Multi-party call
1 Press f to display Option in the option area and press B
2 Press e to select a caller in the Multi-party
3 Press f to display End in the option area
4 Press B
Ending a Multi-party Call
During a Multi-party call:
Press E to end all the calls at once
32
Advanced Operation
Changing to a New Network
When not in your home country you may use a network that you do not directly
subscribe to, this is called ROAMING. National Law may not permit roaming in your
home country.
The New Network function is used to manually select a network that is available in
your current location.
1 From Idle mode press B 91 to enter the New Network menu
2 Use e to select one from the list of available networks and press B
An X will be displayed in the information area if you cannot register with the selected
network.
When the Search Mode is set to Automatic the phone will automatically reselect a
new network in order to maintain optimum network availability. With the Search
Mode set to Manual the phone will only use a selected network. If coverage is lost
another network should be selected.
The Network List is used when the Search Mode has been set to Automatic. The
location numbers in the Preferred Network List show the search priority.
Selecting Insert stores a new network in the currently displayed location and then
moves other networks down, Edit overwrites the old network with a new one, and
Add stores a new network at the end of the list
33
Additional Features
Additional Features
Desktop Handsfree
Desktop Handsfree enables you to hold a conversation without having to hold the
phone to your ear.
Note: Do NOT hold the phone to your ear in Handsfree mode.
Swapping Between Handsfree and Handheld Calls
During a Handheld call:
1 Use f to until H’free is displayed in the option area
2 Press B
During a Handsfree call:
Press B to revert to Handheld operation
Answering a Call Handsfree
Pressing and holding D will allow the call to be answered Handsfree.
DTMF Tones
DTMF tones can be sent during conversation. These are often used to access voice
mail, paging and computerized home banking. For example, you may need to input a
number to remotely access voice mail messages. A phone number may be stored in
the Phonebook with DTMF tones, allowing the number to be dialled upon recall and
the DTMF number to be sent automatically.
Send DTMF Tones During a Call
Enter digits (0 to 9, # and *)
Pause Dial
Using pauses allows you to send DTMF tones automatically.
1 Enter phone number
2 Press and hold 0 until a P is displayed
3 Enter DTMF digits after the pause, e.g. enter the number
to access voice mail messages.
4 Press D
When the call is successful DTMF tones will be sent after 3 seconds or when D is
pressed.
34
Additional Features
If the DTMF tones are unsuccessful then the destination of your call may require that
the length of the tones be increased.
1 From Idle mode press B 56 to enter the DTMF Length menu
2 Use e to set to Long and press B
Note Pad
During a call you can enter numbers which you may wish to dial when the call has
ended.
During a call:
1 Enter phone number
2 When the call has ended press D to call that number
To store in Phonebook, press A while the number is displayed – see “Store a
Number” page 10.
Accessory Related Features
When Auto Answer is switched on, and Personal Handsfree is connected, a call will
be answered without pressing any keys.
This is also applicable to the Handsfree Car Kit accessory.
See the documentation provided with the relevant Accessory for operational
details.
35
Text Entry
Text Entry
The phone provides a means for entering alphanumeric characters to enter details
into the Phonebook, to create text and e-mail messages etc. This section details the
characters that can be entered and the relevant keys to press.
Text Mode
Normal
(U)
Greek
(V)
Extended
(W)
Numeric
(0-9)
Key
T9®
0
Alternatives
1
Punctuation
space”@,.;:!¡?¿()[]{}’&%+-/\^~|<>=£$¥¤§
2
abc
ABCabc
ABG
AÄÅÆBCÇaäåæàbc
2
3
def
DEFdef
DEZ
DEÉFdeéèf
3
4
ghi
GHIghi
HQI
GHIghiì
4
5
jkl
JKLjkl
KLM
JKLjkl
5
6
mno
MNOmno
NXO
MNÑOÖØmnñoöøò
6
0+P_
1
7
pqrs
PQRSpqrs
PRS
PQRSpqrsß
7
8
tuv
TUVtuv
TUF
TUÜVtuüùv
8
9
wxyz
WXYZwxyz CYW
WXYZwxyz
9
*
Shift/Lock*
*
*
*
*
#
Space
#
#
#
#
* Press * once to enter a single capital letter (subsequent characters will be lower
case). Pressing * twice acts as a keyboard CAPS LOCK function and subsequent
characters will be uppercase, until * is pressed for a third time returning to
lowercase character entry.
T9® Text Input
Using this mode of text entry dramatically reduces the number of key presses
required:
Press a key once for any letter you require on that key. The desired letter may not
be displayed. Continue pressing other keys until the end of a word is reached; then
check that the word has been typed correctly before continuing on to the next word.
36
Text Entry
If the combination of letters typed has produced a word which is not the one you
require, press 0 repeatedly until the correct word is displayed. Continue to the
next word.
If the word you require is not in the internal dictionary (i.e. It is a proper noun or a
rarely used word) then it should be entered using the Normal (U) mode.
Other Text Modes
To access any of the other text entry modes use A to cycle through until the desired
mode is displayed in the Information Area.
When using Normal (U), Greek (V) or Extended (W) text entry modes, each
time a key is pressed in quick succession it will display the next character available on
that key (or if the key is pressed and held down it will cycle through the available
characters). Releasing the key, or pressing another key will enter the currently
displayed character and the cursor will move to the next position.
Editing Text
Pressing e will move you up or down one text line (or field in Phonebook). Pressing
f will move you left or right one character (or to the first character of the previous or
®
next word when using T9 text entry mode). When the cursor is moved over a
character and another key pressed this will insert the new character immediately
before the selected character. Pressing C will delete the character to the left of the
cursor or delete the current line when pressed and held.
T9® is a trademark of Tegic Communications Inc.
37
Menu Structure
Menu Structure
From Idle mode pressing B will display a menu of phone features. To select a
feature press e so that the pointer is showing next to the feature that you require
then press B.
To exit the current menu and return to the previous level press C. To exit completely
out of the menu structure, press and hold C, or E (except during a call).
1 Key Guard
2 Phonebook
3 Messages
4 Applications
5 Personalise
6 Call Service
7 Call Divert
8 Security
9 Network
38
Browse
Create
Group Setting
Review
My Numbers
Hot Key Dial
Personal Dial
Clock Function
Calculator
Currency
Language
Tones
Display Setting
Vibration Alert
Auto Answer
DTMF Length
Defaults
Phone Lock
Call Bar
PIN
PIN2
Fixed Dial
Barred Dial
Clock Set
Clock Format
Alarm Set
Power On Time
Power Off Time
Receive List
Send List
Create
User Defined Msg
Review
Parameters
Broadcasts
Display Language
Tegic language
Greeting
Contrast
Animation
Voice Calls
Fax Calls
Data Calls
Cancel All
Status
Bar Voice
Bar Fax
Bar Data
Cancel All
Status
Password
All Tones
Ring Volume
Ring Type
Voice Ringer
Key Volume
Warning Tone
Last Call
All Calls
Call Waiting
Caller’s ID
Withhold ID
Call Charge
Cost Left
Price/Unit
Max Cost
Warning at
New Network
Search Mode
Network List
Trouble Shooting
Trouble Shooting
Should any problem persist contact your dealer.
Problem
Cause
Remedy
Check that the Battery Pack is fully
charged and correctly connected to
the phone
Telephone will not
switch on
Extremely short
battery life for a
new battery pack
The network you are
using and the
condition of the
battery pack can
affect battery life
Short battery life
for an old battery
pack
The battery pack has
Replace with a new one
worn out
The charging
indicator does not
light and the phone
cannot be switched
on when charging
When the Battery
Pack has been
deeply discharged
the phone will take a
short time until the
indicator lights
Short battery life
for Ni-MH battery
pack
To maintain maximum performance
always use until the Low Battery
Warning and then fully recharge
The life of the battery the battery pack.
pack is affected by
To revive the battery pack use the
improper charging,
telepone until the Low Battery
this is inherent in all Warning and then fully recharge
Ni-MH batteries
three times. However, if the battery
life is still short, the battery pack
has eventually worn out. Replace
with a new one.
Calls cannot be
made
Leave the phone charging the
Battery Pack for a few minutes
before the indicator is lit and
attempting to switch it on
The phone is locked
Unlock the phone
Outgoing calls are
barred
Disable the outgoing call barring, or
barred dial
The phone is not
registered to a
network
Move to a coverage area and
operate your phone after it has
registered with a network.
39
Trouble Shooting
Check your SIM supports Fixed
Dial
Check if the Fixed Dial is switched
on
Check the phone number is stored
in the Fixed Dial
Calls cannot be
made from Fixed
Dial Store
Calls cannot be
received
Emergency calls
cannot be made
The phone is not
switched on
Switch the phone on
Incoming calls are
barred
Disable the incoming call barring
The phone is not
registered to a
network
Move to a coverage area and
operate your phone after it has
registered with a network.
You are not in a
GSM coverage area
Check that the antenna symbol S
is displayed - move to a coverage
area and operate your phone when
the antenna symbol is displayed
The phone is locked
Telephone
numbers cannot be
Phone number has
recalled from
been restricted
Phonebook
Unlock the phone
Switch off restriction
Important Error Messages
These are some of the most important error messages which may be displayed:
Area Not Allowed
Roaming in the selected area is not allowed
Network Not
Allowed
Roaming with the selected network is not allowed
Security Failure
The network has detected an authentication failure
because your SIM is not registered with that network contact your Service Provider
SIM Blocked /
Contact Service
provider
The SIM is blocked because one of the PIN/PIN2
unblocking keys (PUK/PUK2) has been entered incorrectly
ten times - contact your Service Provider
SIM Error
The phone has detected a problem with the SIM - switch
the phone off and then back on; if the message is still
displayed contact your Service Provider
SIM Invalid
The SIM has failed one or more of the SIM personalisation
checks - contact your Service Provider
40
Trouble Shooting
Function
Unavailable
The selected feature is either not supported by the SIM or
is not available with the current subscription - contact your
Service Provider
PIN2 Invalidated
The PIN2 is blocked permanently because the wrong
PUK2 has been entered ten times, services controlled by
PIN2 cannot be used - contact your Service Provider
Message Rejected
Store Full
A message has been received but the message store is
full - to receive messages, delete some of the currently
stored messages or set messages to Auto Delete
Number Too Long
(Max:20)
The edited or newly created Phonebook number is too
long for the SIM
Warning Store Full
Continue?
The message area is full. Your messages cannot be stored
until some of the currently stored messages are deleted
Verification Failure
On changing the phone lock code, verification of the new
code is incorrect - retry changing the lock code with correct
verification
Incorrect Lock
Code
Disabling or enabling the lock code has failed due to
incorrect entry of the lock code - re-enter lock code
Invalid PIN / PIN2 /
PUK / PUK2
The entered code is incorrect - re-enter code correctly
Auto Redial List
Full
Redial list of unsuccessfully dialled numbers is full - switch
the phone off and then on again
41
Important Information
Important Information
Safety Considerations
The following information should be read and understood as it provides details which
will enable you to operate your phone in a manner which is both safe to you and your
environment, and conforms to any legal requirements regarding the use of cellular
phones.
This equipment should only be charged with approved charging
equipment, e.g. AC Adaptor (EB-CAD52xx*) - supplied in the Main Kit.
Other usage will invalidate any approval given to this apparatus and
may be dangerous. The use of approved charging equipment is
recommended to ensure optimum performance and avoid damage to
your phone. Ensure the voltage rating of the AC Adaptor is compatible
with the country of use when travelling abroad.
Other recommended equipment for charging includes DC Adaptor
(EB-CDD92), and Handsfree Car Kit (EB-HFD52Z).
* Where xx identifies the specific AC Adaptor region, e.g. CN, EU, HK, TW, UK.
Switch off your cellular phone when in an aircraft. The use of cellular
phones in an aircraft may be dangerous to the operation of the aircraft,
disrupt the cellular network and may be illegal. Failure to observe this
instruction may lead to the suspension or denial of cellular phone
services to the offender, or legal action or both.
You are advised not to use the equipment at a refuelling point. You are
reminded to observe restrictions on the use of radio equipment in fuel
depots, chemical plants or where blasting operations are in progress.
Never expose the battery pack to extreme temperatures (in excess of
60°C) or charge the battery pack for much longer than recommended.
You MUST exercise proper control of your vehicle at all times. Do not
hold a phone while you are driving; find a safe place to stop first. Do not
speak into a handsfree microphone if it will take your mind off the road.
Always acquaint yourself thoroughly with restrictions concerning the
use of cellular phones within the country you are driving and observe
them at all times.
Care must be taken when using the phone in close proximity to personal
medical devices, such as pacemakers and hearing aids.
42
Important Information
For most efficient use hold the phone as you would any normal
telephone. Keep the antenna pointed over your shoulder while in use.
Use only the supplied or approved replacement antenna. Unauthorized
antennas, modifications or attachments may damage the phone and
violate applicable regulations. The use of an unapproved antenna,
modification or attachment may result in the invalidation of your
guarantee – this does not affect your statutory rights.
This Panasonic mobile phone is designed, manufactured and tested to
ensure that it complies with the following specifications covering RF
exposure guidelines;
CENELEC European Pre-standard ENV50166-2
ANSI C95.1-1992 (USA, Asia-Pacific)
AS 2772.1 (Int)-1998 (Australia)
43
Care and Maintenance
Care and Maintenance
Pressing any of the keys may produce a loud tone. Avoid holding the
phone close to the ear while pressing the keys.
Extreme temperatures may have a temporary effect on the operation of
your phone. This is normal and does not indicate a fault.
Do not modify or disassemble the equipment. There are no user
serviceable parts.
Do not subject the equipment to excessive vibration or shock.
Avoid contact with liquids. If the equipment becomes wet immediately
remove the power and contact your dealer.
Do not leave the equipment in direct sunlight or a humid, dusty or hot
area.
Keep metallic items that may accidentally touch the terminals away from
the equipment.
Always charge the Battery Pack in a well ventilated area, not in direct
sunlight, between +5°C and +35°C. It is not possible to recharge the
battery pack if it is outside this temperature range.
Avoid recharging battery packs for longer than recommended.
Do not incinerate or dispose of the battery packs as ordinary rubbish. The
battery packs must be disposed of in accordance with local legislation
and may be recycled.
When disposing of any packing materials or old equipment check with
your local authorities for information on recycling.
44
Glossary of Terms
Glossary of Terms
DTMF Tones
Dual Tone Multi-Frequency tones allow you to
communicate with computerized phone systems, voice
mailboxes etc.
GSM
Global System for Mobile Communications. The name given
to the advanced digital technology that your phone uses.
Home Country
The country where your home network operates.
Home Network
The GSM network on which your subscription details are
held.
Network
Operator
The organization responsible for operating a GSM network.
Password
Used for the control of the Call Bar. Supplied by your
Service Provider.
PIN
Personal Identification Number used for SIM security.
Supplied by your Service Provider. If the PIN is entered
incorrectly 3 times, the PIN will be blocked.
PIN2
Personal Identification Number used for the control of
Fixed Dial Store and Call Charge metering. Supplied by
your Service Provider. If the PIN2 is entered incorrectly 3
times, the PIN2 will be blocked.
PUK/PUK2
PIN/PIN2 Unblocking Key. Used to unblock the PIN/PIN2.
Supplied by your Service Provider. If the PUK/PUK2 is
entered incorrectly 10 times, the PUK/PUK2 will be
blocked.
Registration
The act of locking on to a GSM network. This is usually
performed automatically by your phone.
Roaming
The ability to use your phone on networks other than your
Home network.
Service Provider
The organization responsible for providing access to the
GSM network.
SIM
Subscriber Identity Module. A small smart-card which
stores unique subscriber and user-entered information
such as Phonebook and Short Messages. Supplied by your
Service Provider.
45
Specifications
Specifications
Telephone
Type
Temperature range
Charging
Storage
GSM900 Class 4
GSM1800 Class 1
+5°C to +35°C
-20°C to +60°C
Battery – Attached to phone
Weight
Dimensions
Height x Width x Depth
Supply Voltage
Standby Time - Idle Mode (h)
Talk Time (h)
Charge Time (min)
Battery Pack (S)
99g
118.0 x 40.6 x 21.7mm
3.6V DC, 600mAh Ni-MH
Up to 150
3
150
Note: Charge time will be longer when the phone is turned on. Battery life is affected
by the network you are using and the condition of the battery pack.
46
The Serial Number can be found on the outside of the phone under the battery.
For your convenience we recommend that you note the following details as a
record of your purchase.
Part Number
Serial Number
Dealer Name
Purchase Date
BULL CP8 PATENT
© Matsushita Communication Industrial UK Limited 2000
Information in this document is subject to change without notice. No part of these
instructions may be reproduced or transmitted in any form or by any means without
obtaining express permission from Matsushita Communication Industrial UK
Limited
Printed in UK
www.mcuk.panasonic.co.uk
7LB850A
00.248
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement