Panasonic CD Player C5310U User manual

Panasonic CD Player C5310U User manual

Removable Full Front MP3 WMA CD Player/Receiver with CD Changer Control

CQ-C5410/C5310U

Removable Full Front CD Player/Receiver with CD Changer Control

CQ-C5210/C5110U

(CQ-C5410U)

Please read these instructions carefully before using this product and save this manual for future use.

Prière de lire ces instructions attentivement avant d’utiliser Ie produit et garder ce manuel pour l’utilisation ultérieure.

Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro.

I

S

H

E

N

G

L

Safety Information

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS PRODUCT TO

RAIN OR MOISTURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, AND ANNOYING INTERFERENCE, USE

ONLY THE INCLUDED COMPONENTS.

CAUTION:

T H I S P R O D U C T I S A C L A S S

I

L A S E R

PRODUCT.

USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR

YOURSELF. REFER SERVICING TO QUALIFIED

PERSONNEL.

The following applies only in the U.S.A.

Part 15 of the FCC Rules

FCC Warning:

Any unauthorized changes or modifi cations to this equipment would void the user’s authority to operate this device.

NOTICE:

This product has a fl uorescent lamp that contains a small amount of mercury. It also contains lead in some components.

Disposal of these materials may be regulated in your community due to environmental considerations.

For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance:

<http://www.eiae.org.>

Precautions

When Driving

Keep the volume level low enough to be aware of road and traffi c conditions.

When Washing Your Car

Do not expose the product, including the speakers and CDs, to water or excessive moisture. This could cause electrical shorts, fi re, or other damage.

When Parked

Parking in direct sunlight can produce very high temperatures inside your car. Give the interior a chance to cool down before switching the unit on.

Use the Proper Power Supply

This product is designed to operate with a 12 V DC, negative ground battery system (the normal system in a North American car).

Disc Mechanism

Do not insert coins or any small objects. Keep screwdrivers and other metallic objects away from the disc mechanism and disc.

Use Authorized Servicenters

This product is made of precision parts. Do not attempt to disassemble or adjust any parts. Please refer to the Servicenter list including with this product for service assistance.

For Installation

This product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°.

Note:

The preset memory is cleared to return to the original factory setting when the power connector or battery is disconnected.

Find the model number and serial number on either the back or bottom of the unit. Please record them in the space below and retain this booklet as a permanent record of your purchase to help with identifi cation in case of theft.

2

MODEL NUMBER

SERIAL NUMBER

DATE PURCHASED

FROM

CQ-C5410U / CQ-C5310U / CQ-C5210U / CQ-C5110U

CQ-C5410/5310/5210/5110U

Panasonic

welcomes you to our ever growing family of electronic product owners. We know that this product will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical engineering, manufactured with carefully selected components and assembled by people who take pride in their work. Once you discover the quality, reliability, and value we have built into this product, you too will be proud to be a member of our family.

CQ-C5410/C5310U

Removable Full Front MP3 WMA CD Player/Receiver with CD Changer Control

CQ-C5210/C5110U

Removable Full Front CD Player/Receiver with CD Changer Control

Note:

Please refer to page 9 for information on differences in each model.

Accessories

Item

Remote Control Unit

(YEFX9992663)

Diagram

POWER MENU

SOURCE SEL

NUMBER

MUTE

#

VOL

1

RAND

4

2

SCAN

5

7

6

BAND

SET

8

0

9

5

DISP

3

REP

6

Car Audio

Q’ty

1

Item

Screw Kit

(YEP0FZ3315)

Hex. Nut (5 mm

)

Lithium Battery

%

CR2025

$

1

Tapping Screw

(5 mm

‡t

16 mm)

Mounting Bolt

(5 mm

)

Instruction Kit

Operating Instructions

(YEFM284142)

1

Lock Cancel Plate

Diagram Q’ty

1

1

1

2

I

S

H

E

N

G

L

Warranty Card, etc.

1 set

Rear Support Strap

(YEFG04024)

1

Mounting Collar

(YEFX0216165)

Trim Plate

(YEFC05605)

1

1

Removable Face Plate

Case

(YEFA131839)

Power Connector

(YEAJ02871)

1

1

Note:

The number in parenthesis underneath each accessory part name is the part number for maintenance and service.

Accessories and their parts numbers are subject to modifi cation without prior notice due to improvements.

Mounting collar 1 and trim plate 7 are mounted on the main unit at shipment (page 50).

CQ-C5410/5310/5210/5110U

3

I

S

H

E

N

G

L

Features

MP3/WMA Playback from CD-R/RW

CQ-C5410U CQ-C5310U

You can play your MP3/WMA (Windows Media

Audio) fi les as well as regular CDs.

With up to 10 to 12 times* the capacity of a conventional CD, a single MP3/WMA-encoded disc can keep you entertained throughout your entire journey.

*Depending on bit rate.

SQ7 (7 bands Sound Quality)

SQ is a function that can call up various sound types at the touch of button in accordance with your listening music type.

At SQ7, SQ presets P2 to P6 can also be fi nely adjusted as desired (page 36).

HPF (High Pass Filter)/LPF(Low Pass Filter)

Genuine subwoofer system achieved thanks to HPF

(High Pass Filter) and LPF (Low Pass Filter)

Electronic Switch Front Panel

The front panel opens and closes automatically by pressing a button once.

CD Changer Control

You can connect the optional CD changer unit. For details, refer to the operating instructions on the CD changer unit.

2 CD changers (option) can be controlled with this unit. To connect 2 CD changers to it, the dual CD changer selector CA-CD55U (option) is necessary.

Large-sized Volume Control

A large-sized rotary volume control that looks like one belonging to a Hi-Fi audio system is featured.

System Upgrade

CQ-C5410U

CQ-C5310U

CQ-C5210U

CQ-C5110U

Subwoofer (option)

Before Reading these Instructions

This operating instruction manual applies to the following models. The differences among these models are mentioned below.

All illustrations represent model CQ-C5410U unless otherwise specifi ed.

Features

MP3/WMA playback

Models

CD text display

AUX-IN

SBC-SW (Super Base

Control Sub-Woofer)

Pre-amp output voltage

CQ-C5410U

Yes

Yes

Yes

Yes

5 V

CQ-C5310U

Yes

Yes

Yes

None

2.5 V

CQ-C5210U

None

None

None

Yes

5 V

CQ-C5110U

None

None

None

None

2.5 V

This can only be controlled through

the main unit

.

This can only be controlled through

the remote control unit

.

Operations with neither mark can be performed either by the main unit or the remote control unit.

CQ-C5410U

CQ-C5310U

Indicates features applicable to

CQ-C5410U only.

CQ-C5210U

CQ-C5310U only.

CQ-C5210U only.

CQ-C5110U

CQ-C5110U only.

I

S

H

E

N

G

L

Dual CD changer selector

(CA-CD55U, option)

8

Note:

This unit does not support Sirius satellite radio.

You cannot connect CD changer and Sirius receiver using the dual CD changer selector (CA-CD55U, option).

CQ-C5410/5310/5210/5110U

CD changer

(CX-DP880U, option)

Stereo power amplifi er (option)

CQ-C5410/5310/5210/5110U

9

I

S

H

E

N

G

L

Preparation

Remote Control Unit

Back side

Lithium battery

(included)

2

Position B

Subwoofer

Preparation:

Connect the subwoofer (option). (page 60)

Subwoofer level setting:

You can change the subwoofer level. (page 38)

Subwoofer low pass fi lter setting:

You can select the upper limit frequency of the sound from subwoofer. (page 38)

3

10

Battery holder

Position A

1

Battery Installation

1

Remove the battery holder.

Pull the holder out at position B while pushing position A as indicated.

2

Install the battery on the battery holder.

3

Insert the battery holder back into its original position.

Battery Notes

Battery type: Panasonic lithium battery (CR2025)

(included)

Battery life: Approximately 6 months under normal use (at room temperature)

Caution:

Improper use of the battery may cause overheating, an explosion or ignition, resulting in injury or a fi re.

Remove and dispose of an old battery immediately.

Do not disassemble or short the battery. Do not throw a battery into a fi re.

Keep the battery away from children to avoid the risk of accidents.

Follow local regulations when disposing of the battery.

CQ-C5410/5310/5210/5110U

Clock Setting

The 12-hour system is used for the clock.

Turn your car’s ignition key to the ACC or ON position.

Press [SOURCE] (PWR).

When the power is switched on for the fi rst time, a demonstration appears on the display.

Press [DISP] (display) to change to regular mode. (page 22)

1 Press

[DISP]

(display).

Clock display

2 Press and hold

[DISP]

(display) again for more than 2 seconds.

Hours blink

Hours:

3 Press

[

%

]

or

[

$

]

.

Hours set

4 Press

[DISP]

(display).

Minutes blink

Minutes:

5 Press

[

%

]

or

[

$

]

.

Minutes set

6 Press

[DISP]

(display).

Complete

Note:

“ADJUST” is displayed before adjusting the clock.

Press and hold

[

%

]

or

[

$

]

to change numbers rapidly.

Display Change

Press

[DISP]

(display).

When the power is off:

Clock display (default)

Display off

CQ-C5410/5310/5210/5110U

11

I

S

H

E

N

G

L

L

I

S

H

E

N

G

1

Contents

Safety Information ................................................................................. Page 2

Precautions..................................................................................................... 2

Accessories ............................................................3

Features ................................................................8

Before Reading these Instructions .................................9

Preparation .......................................................... 10

Remote control unit, subwoofer

Clock Setting ........................................................ 11

WELCOME

FM

General ............................................................... 22

Power, source, volume, mute/attenuation, rear speakers as Sub-Woofers (Super

Bass Control Subwoofer/SBC-SW), open/close the front panel, panel angle (tilt), dimmer, SQ (Sound Quality)

Radio ................................................................. 26

Radio mode, band, tuning, display change, Direct Memory (D·M), station preset, preset station calling

Before Disc Playback............................................... 28

Available discs, disc insert, when CD is in the player, disc eject

CD Player ............................................................ 29

Display change, track selection, fast forward/fast reverse, pause, random play, scan play, repeat play, direct track selection

20

MP3/WMA

MP3/WMA Player ................................................... 30

Display change, folder selection, fi le selection, fast forward/fast reverse, pause, random play, folder random play, scan play, folder scan play, repeat play, folder repeat play, direct fi le selection, direct folder selection, notes on MP3/WMA

CD Changer Control ................................................ 34

CD changer mode, display change, disc selection, track selection, fast forward/fast reverse, random play, disc random play, scan play, disc scan play, repeat play, disc repeat play, CD changer selection, direct disc selection

CQ-C5410/5310/5210/5110U

Audio Settings....................................................... 36

Volume, bass/treble, SQ setting, balance/fader, subwoofer level, subwoofer low pass fi lter (LPF), high pass fi lter (HPF)

Function Settings ................................................... 40

Spectrum analyzer display pattern, mute/attenuation, security function

Troubleshooting..................................................... 42

Preliminary steps, if you suspect something wrong, troubleshooting tips, error display messages, maintenance, product servicing, fuse

L

I

S

H

E

N

G

2

Notes on Discs ...................................................... 48

Notes on CD/CD media (CD-R, CD-RW, CD-ROM), notes on CD-Rs/RWs

Anti-Theft System................................................... 49

Remove the removable face plate, install removable face plate, security indicator, panel removal alarm

Installation Guide................................................... 50

Electrical Connections ............................................. 56

Wiring diagram, upgrading the system 1, upgrading the system 2, speaker system connection

Specifi cations ....................................................... 61

CQ-C5410/5310/5210/5110U

21

L

I

S

H

E

N

G

3

General

Source

22

CQ-C5410/5310/5210/5110U

Volume

[VOL

"

]:

Up

[VOL

#

]:

Down

Up

Down

Setting range: 0 to 40

(default: 18)

Note:

The volume level can be set independently for each source. (For radio, one volume setting for

AM, one volume setting for all FMs)

CQ-C5410/5310/5210/5110U

23

L

I

S

H

E

N

G

4

General

(continued)

24

CQ-C5410/5310/5210/5110U CQ-C5410/5310/5210/5110U

25

26

CQ-C5410/5310/5210/5110U

Station Preset

Up to 6 stations can be stored in each of the FM1,

FM2, FM3 and AM band selections.

Auto Preset Memory (APM)

Automatically save stations with good reception in the preset memory.

1 Select a band. (previous page)

2 Press and hold

[BAND]

(

APM:

Auto Preset

Memory) for more than 2 seconds.

The 6 stations with good reception will be automatically saved in the memory under preset number

1

to

6

.

Once set, the preset stations are sequentially scanned for 5 seconds each. (scanning)

Manual Preset Memory

Manually save a station in the preset memory.

1 Select a band and frequency. (previous page)

2 Press and hold one of the buttons from

[1]

to

[6]

until the display blinks once.

Note:

To stop scanning, press one of the buttons from

[1]

to

[6]

.

New stations overwrite existing saved stations after this procedure.

Preset Station Calling

1 Select a band. (previous page)

2 Press one of the preset buttons from

[1]

to

[6]

.

27

CQ-C5410/5310/5210/5110U

L

I

S

H

E

N

G

9

Before Disc Playback

CQ-C5210U/CQ-C5110U cannot play

MP3/WMA fi les.

Disc Insert

1 Press

[

<

: eject] (OPEN)

.

If there is a disc loaded, the disc will be ejected.

2 Insert a disc.

[

<

: eject] (OPEN)

CD Player

Do not watch the scroll display while driving.

Note:

The power will be turned on automatically when a disc is loaded.

A disc which has both CD-DA data and

MP3/WMA data on it may not be reproduced normally. (For example, it may be reproduced without sound.)

Refer to the section on “Notes on MP3/WMA”

(page 32) and “Notes on Discs” (page 48).

28

CQ-C5410/5310/5210/5110U

When placing a disc into or taking a disc out from the main unit, hold it as shown in the fi gure, and refrain from putting any of your fi ngers into the disc’s center hole.

Note:

It may take some time to start playing.

Playback will start automatically after recognizing the data of the loading disc.

Display Change

Press

[DISP]

(display).

Note:

“NO TEXT” is displayed when there is no information on the disc.

Press

[3] (SCROLL)

to have an another circle scroll while a title is displayed. If the number of displayed characters is 8 or less, the characters do not scroll.

Track Selection

[

9

]:

Next track

[

:

]:

Beginning of the current track

For the previous track, press twice.

Fast Forward/Fast Reverse

Press and hold

[

9

] (

5

):

Fast forward

[

:

] (

6

):

Fast reverse

Release to resume the playback.

Pause

Press

[

;

/

1

]

.

Press

[

;

/

1

]

again to cancel.

Random Play

All available tracks are played in a random sequence.

Press

[4] (RANDOM)

. ( lights.)

Press

[4] (RANDOM)

again to cancel.

Scan Play

The fi rst 10 seconds of each track is played in sequence.

Press

[5] (SCAN)

.

Press

[5] (SCAN)

again to cancel.

Repeat Play

The current track is repeated.

Press

[6] (REPEAT)

. ( lights.)

Press

[6] (REPEAT)

again to cancel.

Direct Track Selection

Example: track number 10

1 Press

[

]

.

2 Press

[1] [0]

.

3 Press

[BAND] (SET)

.

Note:

To suspend direct selection, press

[DISP]

(display) or

[

]

.

Random, scan and repeat play are canceled once

[

]

is pressed.

CQ-C5410/5310/5210/5110U

29

L

I

S

H

E

N

G

10

L

I

S

H

E

N

G

11

MP3/WMA Player

Do not watch the scroll display while driving.

Folder Selection

[

"

]:

Next folder

[

#

]:

Previous folder

File Selection

[

9

]:

Next fi le

[

:

]:

Beginning of the current fi le

For the previous fi le, press twice.

Fast Forward/Fast Reverse

Press and hold

[

9

] (

5

):

Fast forward

[

:

] (

6

):

Fast reverse

Release to resume the playback.

Pause

Press

[

;

/

1

]

.

Press

[

;

/

1

]

again to cancel.

CQ-C5210U/CQ-C5110U cannot play MP3/WMA fi les.

L

I

S

H

E

N

G

12

30

CQ-C5410/5310/5210/5110U CQ-C5410/5310/5210/5110U

31

L

I

S

H

E

N

G

13

MP3/WMA Player

(continued)

Notes on MP3/WMA

What is MP3/WMA?

MP3 (MPEG audio layer 3) and WMA (Windows

Media™ Audio) are the compression formats of digital audio. The former is developed by MPEG

(Motion Picture Experts Group), and the latter is developed by Microsoft Corporation. Using these compression formats, you can record the contents of about 10 music CDs on a single CD media. (This fi gures refer to data recorded on a 650 MB CD-R or CD-RW at a fi xed bit rate of 128 kbps and a sampling frequency of 44.1 kHz.)

Note:

MP3/WMA encoding and writing software is not supplied with this unit.

CD writing software is not supplied with this unit.

Points to Remember

When Making MP3/WMA Files

Common:

High bit rate and high sampling frequency are recommended for high quality sounds.

Selecting VBR (Variable Bit Rate) is not recommended because playing time is not displayed properly and sound may be skipped.

The playback sound quality differs depending on the encoding circumstances. For details, refer to the user manual of your own encoding software and writing software.

MP3:

It is recommended to set the bit rate to “128 kbps or more” and “fi xed”.

WMA:

It is recommended to set the bit rate to “64 kbps or more” and “fi xed”.

Do not set the copy protect attribute on the WMA fi le to enable this unit to playback.

Caution:

Never assign the “.mp3”, or “.wma” fi le name extension to a fi le that is not in the

MP3/WMA format. This may not only produce noise from the speaker damage, but also damage your hearing.

CQ-C5410U CQ-C5310U

Display Information

Displayed Items

CD-TEXT MP3 (ID3 tag)

Disc title

Album title

Track title

Title and artist

MP3/WMA WMA (WMA tag)

Folder name

Album title

File name

Title and artist

Displayable Characters

Displayable length of fi le name/folder name: within 128 characters

Name fi les and folders in accordance with the standard of each fi le system. Refer to the instructions of writing software for details.

ASCII character set and special characters in each language can be displayed.

ASCII character set:

A to Z, a to z, digits 0 to 9, and the following symbols:

(space) ! ” ’ # $ % & ( ) * + , - . / : ; < = > ? @ [ \ ] ^

_ ` { | } ~

Special characters:

À Á Â Ã Å Ä à á â ã å ä

Ò Ó Ô Õ Ö ò ó ô õ ö

Ù Ú Û Ü ù ú û ü

Note:

With some software in which MP3/WMA format fi les have been encoded, the character information may not be displayed properly.

Undisplayable characters and symbols will be converted into an asterisk.

Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft

Corporation in the United

States and/or other countries.

32

CQ-C5410/5310/5210/5110U

CQ-C5210U/CQ-C5110U cannot play MP3/WMA fi les.

Recording MP3/WMA Files on a CD-Media

You are recommended to minimize the chances of making a disc that contains both CD-DA fi les and MP3/WMA fi les.

If CD-DA fi les are on the same disc as MP3 or WMA fi les, the songs may not play in the intended order, or some songs may not play at all.

When storing MP3 data and WMA data on the same disc, use different folders for each data.

Do not record fi les other than MP3/WMA fi les and unnecessary folder on a disc.

The name of MP3/WMA fi le should be added by rules as shown in the following descriptions and also comply with the rules of each fi le system.

You may encounter trouble in playing MP3/WMA fi les or displaying the information of MP3/WMA fi les recorded with certain writing software or CD recorders.

The fi le extension “.mp3” or “.wma” should be assigned to each fi le depending on the fi le format.

This unit does not have the play list function.

Although Multi-session recording is supported, the use of Disc-at-Once is recommended.

Folder Selection Order/File

Playback Order

Maximum number of fi les/folders:

Maximum number of fi les: 999

Maximum number of fi les in one folder: 255

Maximum depth of trees: 8

Maximum number of folders:

255 (Root folder is included.)

Note:

This unit counts the number of folders irrespective of the presence or absence of MP3/WMA fi le.

If the selected folder does not contain any

MP3/WMA fi les, the nearest MP3/WMA fi les in the order of playback will be played.

Playback order may be different from other

MP3/WMA players even if the same disc is used.

“ROOT” appears when displaying the root folder name.

1

Root folder (root directory)

2

4

Folder selection

3

File selection

In the order to

Supported fi le systems:

ISO 9660 Level 1/Level 2, Apple Extension to ISO

9660, Joliet, Romeo

5

6

Note:

Apple HFS, UDF 1.50, Mix CD, CD Extra are not supported.

Tree 1

Tree 2 Tree 3 ........Tree 8 (Max.)

Compression formats:

(Recommendation:

“Points to Remember When Making MP3/WMA Files” on the previous page

)

Compression method

MPEG 1 audio layer 3 (MP3)

Bit rate VBR Sampling frequency

32 kbps−320 kbps Yes 32, 44.1, 48 kHz

MPEG 2 audio layer 3 (MP3) 8 kbps−160 kbps Yes 16, 22.05, 24 kHz

Windows Media Audio Ver. 2/Ver. 8/Ver.9* 64 kbps−192 kbps No 32, 44.1, 48 kHz

6

* WMApro, Loss-less: Not available

64 kbps at 48 kHz: Not available

Copyright:

It is prohibited by copyright laws to copy, distribute and deliver copyrighted materials such as music without the approval of copyright holder except enjoying yourself personally.

No warranty:

Above description complies with our investigations as of December 2003. It has no warranty for reproducibility and displayability of MP3/WMA.

CQ-C5410/5310/5210/5110U

33

L

I

S

H

E

N

G

14

L

I

S

H

E

N

G

15

CD Changer Control

34

CD changer functions are designed for optional

Panasonic CD changer unit.

Connect the CD changer, and load a magazine

(CDs).

Note:

The power will be turned on automatically when a magazine is loaded.

This unit does not support the following through the CD changer.

· CD-RW playback

(except when CX-DP880U is connected.)

· CD text display

· MP3/WMA playback

Pausing does not function in the changer mode.

Display Change

Press

[DISP]

(display).

Disc Selection

[

"

]:

Next disc

[

#

]:

Previous disc

Track Selection

[

9

]:

Next track

[

:

]:

Beginning of the current track

For the previous track, press twice.

Fast Forward/Fast Reverse

Press and hold

[

9

] (

5

):

Fast forward

[

:

] (

6

):

Fast reverse

Release to resume the playback.

Random Play

All the available tracks are played in a random sequence.

Press

[4] (RANDOM)

. ( lights.)

Press

[4] (RANDOM)

again to cancel.

CQ-C5410/5310/5210/5110U CQ-C5410/5310/5210/5110U

35

L

I

S

H

E

N

G

16

L

I

S

H

E

N

G

17

Audio Settings

1

Press

[VOLUME]

(

SEL:

select).

Volume

Default:18 Setting range: 0 to 40

Bass/Treble

You can adjust the bass and treble sound.

Default: BAS (bass) 0 dB

TRE (treble) 0 dB

Setting range: j

12 dB to i

12 dB (by 2 dB)

SQ Adjustment

You can adjust the characteristics of the currently selected sound type (SQ).

It is also possible for a maximum of 5 different adjusted SQ to be preset.

Adjustable frequency:

60 Hz, 160 Hz, 400 Hz, 1 kHz, 3 kHz, 6 kHz, 16 kHz

Setting range: j

12 dB to i

12 dB (by 2 dB)

Setting of SQ, bass/treble and volume are infl uenced one another. If the infl uence mentioned above causes distortion to the audio signal, readjust bass/treble or volume.

36

CQ-C5410/5310/5210/5110U

(page 38)

2

Turn

[VOLUME]

.

(Press

[VOL

"

]

or

[VOL

#

]

on the remote control unit.)

[VOLUME

"

]:

Up

[VOLUME

#

]:

Down

[VOLUME

"

]:

Increased

[VOLUME

#

]:

Decreased

[VOLUME

"

]:

Increased

[VOLUME

#

]:

Decreased

Note:

Press

[DISP]

(display) to return to the regular mode.

If no operation takes place for more than

5 seconds in audio setting (2 seconds in the volume setting, 10 seconds in SQ adjustment), the display returns to the regular mode.

The volume can also be adjusted directly using

[VOLUME]

on the main unit.

L

I

S

H

E

N

G

18

CQ-C5410/5310/5210/5110U

37

Audio Settings

(continued)

1

Press

[VOLUME]

(

SEL:

select).

(Push.)

Balance/Fader

You can adjust the sound balance among the front, rear, right and left speakers.

Default: BAL (balance) CNT (center)

FAD (fader) CNT (center)

Setting range: 15 levels each

Subwoofer Level

You can change the subwoofer volume level.

Default: 0 dB

Setting range: MUTE (subwoofer mute), j

6 dB to i

6 dB (by 2 dB)

Subwoofer Low Pass Filter (LPF)

You can select the upper limit frequency of the sound from subwoofer.

Default: 80 Hz

Setting range: 80 Hz/120 Hz/160 Hz

High Pass Filter (HPF)

Select the lower limit frequency of the sound from speakers (except subwoofer)

Default: OFF

Setting range: OFF/90 Hz/135 Hz/180 Hz/225 Hz

38

CQ-C5410/5310/5210/5110U

2

Turn

[VOLUME]

.

(Press

[VOL

"

]

or

[VOL

#

]

on the remote control unit.)

[VOLUME

"

]:

Right enhanced

[VOLUME

#

]:

Left enhanced

[VOLUME

"

]:

Front enhanced

[VOLUME

#

]:

Rear enhanced

[VOLUME

"

]:

Increased

[VOLUME

#

]:

Decreased

Note:

Press

[DISP]

(display) to return to the regular mode.

If no operation takes place for more than

5 seconds in audio setting (2 seconds in the volume setting, 10 seconds in SQ adjustment), the display returns to the regular mode.

When SBC-SW setting (page 23) has been selected to ON, the settings resulting from the adjustments performed at the subwoofer level and subwoofer low pass fi lter settings are refl ected in the output.

[VOLUME

"

]:

Increased

[VOLUME

#

]:

Decreased

[VOLUME

"

]:

Increased

[VOLUME

#

]:

Decreased

CQ-C5410/5310/5210/5110U

39

L

I

S

H

E

N

G

21

Function Settings

1

Press

[MENU].

(Press and hold

[MENU]

for more than 2 seconds on the remote control unit.)

2

Press

[MENU].

The only items which can be set using

[MENU]

on this unit are the Function Settings (Spectrum

Analyzer Display Pattern, Mute/Attenuation and

Security Function).

(Example: Radio mode)

Spectrum Analyzer Display

Pattern

Default: Pattern 1

Variety: 6 types

_

OFF

Select

Mute/Attenuation

You can select mute or attenuation when

[MUTE]

is pressed (page 23).

Default: MUTE

Security Function

Allows you to activate the anti-theft function when leaving your car.

Default: ON

Select

Select

3

Press

[SET]

.

OFF

Pattern 1

Pattern 6

[MENU]

[SET]

POWER

SOURCE

MENU

SEL

MUTE

NUMBER

#

VOL

1

RAND

4

2

SCAN

5

3

REP

6

7

6

BAND

SET

8

0

9

5

DISP

Car Audio

[DISP]

(Display)

L

I

S

H

E

N

G

22

Note:

No settings can be performed while "NO

DISC" appears on the display.

Press

[DISP]

(display) to return to the regular mode.

Decrease 10 steps

(Attenuation)

No sound

(Mute)

Security function is activated.

Security function is not activated.

Security Function

When the key in the ignition is turned OFF

Security message will be displayed.

The panel removal alarm will be active.

(page 49)

When the front panel is removed

The security indicator blinks. (page 49)

40

CQ-C5410/5310/5210/5110U CQ-C5410/5310/5210/5110U

41

L

I

S

H

E

N

G

23

Troubleshooting

Preliminary Steps

Check and take steps as described in the tables below.

If You Suspect Something Wrong

Immediately switch the power off.

Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit by yourself because it is dangerous to do so.

Troubleshooting Tips

Common

Problem Possible cause

No power to the unit

Caution:

Do not use the unit if it malfunctions or if there is something wrong.

Do not use the unit in abnormal condition, for example, without sound, or with smoke or foul smell, which can cause ignition or electric shock. Immediately stop using it and call the store where you purchased it.

Possible solution

The power cord (battery, ACC and ground) is connected in the wrong way.

Check the wiring.

Fuse blow out.

The Power fails unintentionally

The safety device works.

Eliminate the cause of fuse blow out and replace the fuse with new one.

Consult your dealer.

Call the store where you purchased the unit, or your nearest Panasonic

Servicenter.

Sound is not generated.

The demonstration screen displayed and no operable.

Some operations are not executable.

MUTE is set to ON.

The wiring of the speaker lines are not correct, or a break or poor contact arises.

Set MUTE to OFF.

Check the wiring in accordance with the wiring diagram.

You cannot operate the unit while the demonstration screen appears.

If the demonstration screen appears frequently, there is a possibility that poor contact or wrong wiring arises between the battery lead of the unit and the battery cable of the car.

(The battery lead should be always powered.)

Press [DISP] (display) to end the demonstration screen.

Check the battery wiring in accordance with the wiring diagram.

Some operations are not executable in particular modes such as menu mode.

Read the operating instructions carefully and cancel the mode. In case the unit is still out of order, consult the dealer.

42

CQ-C5410/5310/5210/5110U

Noise

Problem

Noise is made in step with engine revolutions.

No sound from speaker (s)

Possible cause Possible solution

There is an electromagnetic-wave generator such as a cellular phone near the unit or its electrical lines.

The contact of the ground lead is poor.

Keep an electromagnetic-wave generator such as a cellular phone away from the unit and the wiring of the unit. In case the noise cannot be eliminated due to the wiring harness of the car, consult your dealer.

Make sure that the ground lead is connected to an unpainted part of the chassis securely.

Alternator noise comes from the car.

Change the wiring position of the ground lead.

Mount a noise fi lter on the power supply.

Readjust balance/fader.

Balance/fader setting is not appropriate.

There is a break, a short circuit, poor contact or wrong wiring regarding the speaker wiring.

Some speakers are out of order.

The speaker wiring is confused between right and left.

Check the speaker wiring.

Replace the speaker with new one.

Perform the speaker wiring in accordance with the wiring diagram.

L

I

S

H

E

N

G

24

The speaker channels are reversed between right and left.

Radio

Poor reception or noise

The number of auto preset stations are less than 6.

Preset stations cannot be stored.

Antenna installation or wiring of antenna cable is faulty.

Check whether the antenna mounting position and its wiring are correct.

In addition, check to see whether the antenna ground is securely connected to the chassis.

Check the wiring of the antenna battery lead.

No power is supplied to the antenna amplifi er (when using a fi lm antenna, etc.).

The number of receivable stations are less than 6.

Move to an area where receivable stations number is maximum, and try presetting.

The contact of the battery lead is poor, or the battery lead is not always powered.

Make sure that the battery lead is connected securely, and preset stations again.

CQ-C5410/5310/5210/5110U

43

L

I

S

H

E

N

G

25

Troubleshooting

(continued)

CD/MP3/WMA

CD

CQ-C5410U CQ-C5310U

CQ-C5210U CQ-C5110U

Problem

No playback or disc ejected

Possible cause Possible solution

The disc is inserted upside down.

Insert a disc correctly.

There is a fl aw or foreign objects on the disc.

Remove the foreign objects, or use a fl awless disc.

The disc has unplayable formatted data.

The unit plays back the ROM track of a mix mode CD.

Refer to the description about

MP3/WMA for playable sound data except CD-DA (i.e. music CD).

Skip the ROM track.

The CD-R/RWs that are playable on other devices are not playable on this unit.

The playability of some CD-R/RWs may depend on the combination of media, recording software and recorder to be used even if these CD-R/RWs are playable on other devices such as a personal computer.

Make CD-R/RWs in different combination of media, recording software and recorder after referring to the description about MP3/WMA.

Sound skipping or noise

There is a fl aw or foreign objects on the disc.

Remove the foreign objects, or use a fl awless disc. For MP3/WMA, refer to the description about MP3/WMA.

Sound skipping due to vibration

Disc unejectable

The unit is not suffi ciently secured.

Secure the unit to the console box with the rear support strap, etc.

The unit is tilted at over 30° in the front-to-end direction.

Make the angle 30° or less.

Something such as a peeled obstructs the disc coming out.

The microcontroller in the unit operates abnormally due to noise or other factors.

Note:

Refer to the section on “Notes on MP3/WMA” (page 32).

Press and hold [

<

: eject] (OPEN) for more than 4 seconds when the front panel is open (disc forced ejection). In case that the disc forced ejection does not work, consult the dealer.

Unplug the power cord and plug it again. In case the unit is still out of order, consult the dealer.

44

CQ-C5410/5310/5210/5110U

Remote Control Unit

Problem

No response to pressing buttons

Possible cause Possible solution

The battery is inserted in the wrong direction. A wrong battery is inserted.

Insert a correct battery in the correct direction.

The battery is weak.

Replace the battery with new one.

The aiming direction of the remote control unit is wrong.

Aim the remote control unit at the sensor of the unit and press buttons.

Block off sunlight to the sensor.

The sensor is exposed to direct sunlight. (The remote control unit may not be operable when the sensor is exposed to direct sunlight. In such a case, the system is not faulty.)

Error Display Messages

CD/MP3/WMA

CQ-C5410U CQ-C5310U

CD

CQ-C5210U CQ-C5110U

Display Possible cause

MP3/WMA

§

WMA

§

Disc is dirty, or is upside down.

Disc has scratches.

No operation by some cause.

Possible solution

Check the disc.

Check the disc.

If normal operation is not restored, call the store where you purchased the unit or the nearest Servicenter to ask for repairs.

The player cannot read the fi le you are trying to play for some reasons.

(File recorded in an unsupported fi le system, compression scheme, data format, fi le name extension, damaged data, etc.)

Select a fi le that the player can read.

Confi rm the type of data recorded on the disc. Create a new disc if necessary.

An attempt has been made to play a copy-protected WMA fi le.

Play WMA fi les which are not copy-protected.

No disc in the player.

§

If all the fi les cannot be played, E4 or E5 remains on the display.

Insert a disc into the player.

CQ-C5410/5310/5210/5110U

45

L

I

S

H

E

N

G

26

L

I

S

H

E

N

G

27

Troubleshooting

(continued)

CD Changer Control

Display Possible cause

Disc is dirty, or is upside down.

A disc other than a music CD

(CD-DA type) is loaded.

Disc has scratches.

No operation by some cause.

No disc is in the changer

(magazine).

Possible solution

Check the disc.

(The changer automatically switches to the next disc.)

Check the disc.

(The changer automatically switches to the next disc.)

If normal operation is not restored, call the store where you purchased the unit or the nearest Servicenter to ask for repairs.

The display continues if you cannot switch off the power.

Insert discs into the changer

(magazine).

The dual CD changer selector is connected but the changers are not connected.

The changer has become disconnected from this unit in the changer mode.

Verify that correct connections have been made.

Note:

Messages in the action and display sections of the error chart vary with changers.

Refer to the operating instructions of the CD changer for details.

Maintenance

Your product is designed and manufactured to ensure a minimum of maintenance. Use a dry and soft cloth for routine exterior cleaning. Never use benzine, thinner or other solvents.

Product Servicing

If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized Panasonic Servicenter. The product should be serviced only by a qualifi ed technician.

Fuse

Use fuses of the same specifi ed rating (15 A). Using different substitutes or fuses with higher ratings, or connecting the unit directly without a fuse, could cause fi re or damage to the unit.

If the replacement fuse fails, contact your nearest

Panasonic Servicenter for service.

46

CQ-C5410/5310/5210/5110U CQ-C5410/5310/5210/5110U

47

L

I

S

H

E

N

G

28

L

I

S

H

E

N

G

29

Notes on Discs

Notes on CD-Rs/RWs

You may have trouble playing back some

CD-R/RW discs recorded on CD recorders

(CD-R/RW drives), either due to their recording characteristics or dirt, fi ngerprints, scratches, etc. on the disc surface.

CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving them inside a car for extended periods may damage them and make playback impossible.

Some CD-R/RWs cannot be played back successfully thanks to incompatibility among writing software, a CD recorder (CD-R/RW drive) and the discs.

This player cannot play the CD-R/RW discs if the session is not closed.

This player cannot play the CD-R/RW discs which contains other than CD-DA (or MP3/WMA data

Be sure to observe the instructions of CD-R/RW disc for handling it.

Anti-Theft System

Caution:

This face plate is not waterproof. Do not expose it to water or excessive moisture.

Do not remove the face plate while driving your car.

Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level.

Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts.

Remove the Removable Face Plate

1

Switch off the power of the unit

(page 22).

2 Press

[ ]

(release) to remove the removable face plate.

(The face plate disengages with a click when it is removed.)

If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth.

To avoid damaging the face plate, do not push it down or place objects on it while it is open.

The front panel will automatically close about

5 seconds after

[ ]

(release) is pressed while the front panel is tilted or open, so take care to ensure that your fi ngers will not be pinched by the closing panel.

Contact

L

I

S

H

E

N

G

30

1

2

Note:

Be absolutely sure to turn off the main unit’s power before removing the removable face plate.

Do not install or remove the removable face plate while it is moving.

3 Gently press the bottom of the case and open the cover. Place the face plate into the case and take it with you when you leave the car.

Security Indicator

The security indicator blinks when the face plate is removed from the unit.

This function is activated when the security function is on. (page 40)

Security indicator

48

CQ-C5410/5310/5210/5110U CQ-C5410/5310/5210/5110U

49

L

I

S

H

E

N

G

31

Installation Guide

WARNING

This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product.

Any attempt to install this product in a motor car by anyone other than a qualifi ed installer could cause damage to the electrical system and could result in serious personal injury or death.

If your car is equipped with air bags and/or anti-theft systems specifi c procedures may be required for connection and disconnection of the battery to install this product.

Before attempting installation of this electronic component contact your car dealer or manufacturer to determine the required procedure and strictly follow their instructions.

FAILURE TO FOLLOW THE PROCEDURE

MAY RESULT IN THE UNINTENDED

DEPLOYMENT OF AIR BAGS OR

ACTIVATION OF THE ANTI-THEFT

SYSTEM RESULTING IN DAMAGE TO

THE VEHICLE AND PERSONAL INJURY.

Caution:

This unit operates with a 12 V DC negative ground auto battery system only.

Do not attempt to use it in any other system.

Doing so could cause serious damage.

Installation Hardware

No.

Item

1 Mounting collar

Diagram Q’ty

1

2 Hex. nut (5 mm

)

3 Rear support strap

4 Tapping screw

(5 mm

‡k

16 mm)

5 Mounting bolt

(5 mm

)

6 Power connector

7

Trim plate

8 Lock cancel plate

1

1

2

1

1

1

1

Required Tools

You’ll need a screwdriver, a 1.5 V AA battery, and the following:

12 V DC

Test bulb

Electrical tape Side-cut pliers

50

CQ-C5410/5310/5210/5110U

Overview

This product should be installed by a professional.

However, if you plan to install this product yourself, your fi rst step is to decide where to install it. The instructions in these pages will guide you through the remaining steps:

(Please refer to the “WARNING” statement.)

Identify and label the car wires.

Connect the car wires to the wires of the power connector.

Install the unit in the dashboard.

Check the operation of the unit.

If you encounter problems, please consult your nearest professional installer.

Before you begin installation, look for the items which are packed with your unit.

Warranty Card

... Fill this out promptly.

Panasonic Servicenter List for Service

Directory

... Keep for future reference in case the product needs servicing.

Installation Hardware

... Needed for in-dash installation.

Dashboard Specifi cations

Thickness Min.

3

/

16 q

(4.75 mm)

Max.

7

/

32 q

(5.56 mm)

2 3 /

32 q

(53 mm)

7 5 /

32 q

(182 mm)

Preparation

We strongly recommend that you wear gloves for installation work to protect yourself from injuries.

When bending the mounting tabs of the mounting collar with a screwdriver, be careful not to injure your hands and fi ngers.

Disconnect the cable from the negative battery terminal (see caution below).

Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30 o

.

L

I

S

H

E

N

G

32

Less than 30 o

Caution:

If your car is equipped with air bags and/or anti-theft systems specifi c procedures may be required for connection and disconnection of the battery to install this product.

Before attempting installation of this electronic component contact your car dealer or manufacturer to determine the required procedure and strictly follow their instructions.

FAILURE TO FOLLOW THE PROCEDURE MAY

RESULT IN THE UNINTENDED DEPLOYMENT

OF AIR BAGS OR ACTIVATION OF THE

ANTI-THEFT SYSTEM RESULTING IN DAMAGE

TO THE VEHICLE AND PERSONAL INJURY.

Note:

Various settings that have been stored in the memory in other on-board equipment (car navigation etc.) may be lost if the battery terminals are disconnected.

Therefore, we recommend to make a record of or to back up the settings before disconnecting the terminals.

After completing installation of the main unit, set the equipment again according to the record.

Dashboard Installation

Installation Opening

2 3 /

32 q

(53 mm)

7

5

/

32 q

(182 mm)

This unit can be installed in any dashboard having an opening as shown above. The dashboard should be 3 /

16 q

(4.75 mm)– 7 /

32 q

(5.56 mm) thick in order to be able to support the unit.

CQ-C5410/5310/5210/5110U

51

L

I

S

H

E

N

G

33

Installation Guide

(continued)

Identify All Leads

The fi rst step in installation is to identify all the car wires you’ll use when hooking up your sound system.

As you identify each wire, we suggest that you label it using masking tape and a permanent marker. This will help avoid confusion when making connections later.

Note:

Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Identify the leads in the following order.

Power Lead

If your car has a radio or is pre-wired for one:

Cut the connector wires one at a time from the plug

(leaving the leads as long as possible) so that you can work with individual leads.

Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis.

Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug.

Touch one wire at a time until you fi nd the outlet that causes the test bulb to light.

Now turn the ignition off and then on. If the bulb also turns off and on, that outlet is the car power lead.

If your car is not wired for an audio unit:

Go to the fuse block and fi nd the fuse port for radio

(RADIO), accessory (ACC), or ignition (IGN).

Battery Lead

If your stereo unit has a yellow lead, you will need to locate the car’s battery lead. Otherwise you may ignore this procedure. (The yellow battery lead provides continuous power to maintain a clock, memory storage, or other function.)

If your car has a radio or is pre-wired for one:

With the ignition and headlights off, identify the car battery lead by grounding one lead of the test bulb to the chassis and checking the remaining exposed wires from the cut radio connector plug.

If your car is not wired for an audio unit:

Go to the fuse block and fi nd the fuse port for the battery, usually marked BAT.

Speakers

Identify the car speaker leads. There are two leads for each speaker which are usually color coded.

A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1.5 V AA battery as follows.

Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead.

If not, keep testing different lead combinations until you have located all the speaker leads. When you label them, include the speaker location for each.

Antenna Motor

If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire.

Antenna

The antenna lead is a thick, black wire with a metal plug at the end.

52

CQ-C5410/5310/5210/5110U

Connect All Leads

Now that you have identifi ed all the wires in the car, you are ready to begin connecting them to the stereo unit wires. The wiring diagram (page 56) shows the proper connections and color coding of the leads.

We strongly recommend that you test the unit before making a fi nal installation.

You can set the unit on the fl oor and make temporary connections to test the unit. Use electrical tape to cover all exposed wires.

Important:

Connect the red power lead last, after you have made and insulated all other connections.

Ground

Connect the black ground lead of the power connector to the metal car chassis.

Speakers

Connect the speaker wires. See the wiring diagram

(page 56) for the proper hookups. Follow the diagram carefully to avoid damaging the speakers and the stereo unit.

The speakers used must be able to handle more than 50 W of audio power. If using an optional audio amplifi er, the speakers should be able to handle the maximum amplifi er output power.

Speakers with low input ratings can be damaged.

Speaker impedance should measure 4–8

, which is typically marked on most speakers. Lower or higher impedance speakers will affect output and can cause both speaker and stereo unit damage.

Motor Antenna

Connect the car motor antenna lead to the dark blue motor antenna relay control lead.

(Do not confuse the antenna lead with blue/white stripe lead for a power amplifi er.)

Battery

Connect the yellow battery lead to the correct radio wire or to the battery fuse port on the fuse block.

Antenna

Connect the antenna by plugging the antenna lead into the antenna receptacle.

Equipment

Connect any optional equipment such as an amplifi er, according to the instructions furnished with the equipment. Leave about 12 q

(30 cm) of distance between the speaker leads/amplifi er unit and the antenna/antenna extension cord. Read the operating and installation instructions of any equipment you will connect to this unit.

Power

Connect the red power lead to the correct car radio wire or to the appropriate fuse port on the fuse block.

If the stereo unit functions properly with all these connections made, disconnect the wires and proceed to the fi nal installation.

Final Installation

Lead Connections

Connect all wires, making sure that each connection is insulated and secure. Bundle all loose wires and fasten them with tape so they will not fall down later. Now insert the stereo unit into the mounting collar.

Congratulations! After making a few fi nal checks, you’re ready to enjoy your new auto stereo system.

Final Checks

1. Make sure that all wires are properly connected and insulated.

2. Make sure that the stereo unit is securely held in the mounting collar.

3. Turn on the ignition to check the unit for proper operation.

If you have diffi culties, consult your nearest authorized professional installer for assistance.

L

I

S

H

E

N

G

34

CQ-C5410/5310/5210/5110U

53

L

I

S

H

E

N

G

35

Installation Guide

(continued)

54

CQ-C5410/5310/5210/5110U

Remove the Unit

Switch off the power of the unit.

1 Remove the removable face plate. (page 49)

2 Remove the trim plate 7 with a screwdriver.

Screwdriver

7 Trim plate

3 1 Insert the lock cancel plates 8 along the grooves on both sides of the main unit until “click” is heard.

2 Pull out the unit while pushing the plates further inside.

1 Insert.

Insert the tab end in the outer groove.

“Click”

8 Lock cancel plate

L

I

S

H

E

N

G

36

2 Pull out.

4

Remove the unit pulling with both hands.

CQ-C5410/5310/5210/5110U

55

L

I

S

H

E

N

G

37

Electrical Connections

Caution:

This product is designed to operate with a 12 V

DC, negative ground battery system.

To prevent damage to the unit, be sure to follow the connection diagram below.

Remove approximately 1 /

4 q

(5 mm) of protective covering from the ends of the leads before connecting.

Do not insert the power connector into the unit until the wiring is completed.

Be sure to insulate any exposed wires from a possible short-circuit from the car chassis.

Bundle all cables and keep cable terminals free from touching any metal parts.

Remember, if your car has a drive computer or a navigation computer, the data of its memory may be erased when the battery terminals are disconnected.

Wiring Diagram

Accessory used for wiring

No.

6

Item

Power connector

Q’ty

1

CQ-C5310U CQ-C5110U

Pre-amp output connector

(front)

(rear)

L (white)

R (red)

External amplifi er control power lead

(max. 500 mA)

This lead is for connection to the power amplifi er.

Note:

This lead is used for power control when an external power amplifi er is connected. The power supply of a power amplifi er will be activated when turning on the power of this unit.

Dual CD changer control lead

Note:

Insulate this lead with vinyl tape when you do not connect it.

Antenna control lead

(to motor antenna) (max. 500 mA)

This lead is not intended for use with switch actuated power antenna.

Note:

The power antenna extends automatically

when the AM/FM radio mode is selected

.

ACC power lead

To ACC power, i

12 V DC.

Battery lead

To the car battery, continuous i

12 V DC.

56

Ground lead

To a clean, bare metallic part of the car chassis.

CQ-C5410/5310/5210/5110U

ACC

BATTERY 15 A

(Blue/white stripe)

(Brown/white stripe)

(Blue)

(Red)

(Yellow)

(Black)

S.W-OUT

CD.C-IN

AUX-IN

Antenna

CQ-C5410U

CQ-C5210U

CQ-C5310U

Preout cord (front)

PRE-OUT FRONT

Preout cord (rear)

PRE-OUT REAR

Subwoofer cord

S.W-OUT

CD changer input cord

CD.C-IN

CD changer control connector

CQ-C5410U

AUX input cord

AUX-IN

R (red)

L (white)

Fuse (mini auto fuse type, 15 A)

If the fuse (rear panel) blows frequently, they may be something wrong with the unit or wiring connection.

Consult your nearest Panasonic Servicenter for service.

6

Power connector

R (red)

L (white)

R (red)

L (white)

(red)

(white)

Monaural

R (red)

L (white)

L

I

S

H

E

N

G

38

Front speaker lead

FRONT SP

Rear speaker lead

REAR SP

L

R

(White)

+

(White/black stripe)

-

(Gray)

+

(Gray/black stripe)

-

(Green)

+

(Green/black stripe)

-

+

(Violet)

(Violet/black stripe)

-

Left

To front speaker

Right

Left

To rear speaker

Right

Caution:

Do not connect more than one speaker to one set of speaker leads.

CQ-C5410/5310/5210/5110U

57

L

I

S

H

E

N

G

39

Electrical Connections

(continued)

Upgrading the System 1

Example combination

CD changer (CX-DP880U, option)

CD changer input cord

CD.C-IN

R (red)

RCA cord (R)

RCA cord (L)

L (white)

DIN cord

Example: CQ-C5410U

CD changer control connector

Upgrading the System 2

Example combination

CD changer (CX-DP880U, option)

Dual CD changer selector (CA-CD55U, option)

RCA cord

(supplied with CA-CD55U)

Dual changer output cord

R (red)

CD changer input cord

L (white)

DIN extension cord

(supplied with CA-CD55U)

Example: CQ-C5410U

58

6

Power

connector

Remove the vinyl cap.

Cut off the tip.

TWIN CD

.

C-CONT

Note:

For wiring, carefully read the operating instructions

Dual CD changer control lead

(Brown/white stripe) for the devices connected.

This unit does not support Sirius satellite radio.

You cannot connect CD changer and Sirius receiver using the dual CD changer selector (CA-CD55U, option).

CQ-C5410/5310/5210/5110U

CD changer

(CX-DP880U, option)

Note:

For wiring, carefully read the operating instructions for the devices connected.

L

I

S

H

E

N

G

40

Extension cord

(supplied with CX-DP880U)

CD changer

(CX-DP880U, option)

Changer 1 connecting cord

R (red)

RCA cord

L (white)

DIN cord

Extension cord

(supplied with CX-DP880U)

CD changer

(CX-DP880U, option)

R (red)

RCA cord

L (white)

Dual CD changer selector

(CA-CD55U, option)

Changer 2 connecting cord

DIN cord

Extension cord

(supplied with CX-DP880U)

CQ-C5410/5310/5210/5110U

59

60

CQ-C5410/5310/5210/5110U CQ-C5410/5310/5210/5110U

61

Panasonic Consumer

Electronics Company,

Division of Matsushita Electric

Corporation of America

One Panasonic Way, Secaucus,

New Jersey 07094 http://www.panasonic.com

Panasonic Sales Company.

Division of Matsushita Electric of Puerto Rico, Inc. (“PSC”)

Ave. 65 de Infanteria, Km. 9.5

San Gabriel Industrial Park,

Carolina, Puerto Rico 00985 http://www.panasonic.com

Panasonic Canada Inc.

5770 Ambler Drive,

Mississauga, Ontario

L4W 2T3 http://www.panasonic.ca

YEFM284142 FT1003-2113 Printed in China

Imprimé en Chine

Impreso en China

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project