Thermador Ventilation Hood PH30ZS, PH36ZS, PH42ZS, PH48ZS, PH54ZS, PHI48ZS, PHI60ZS User manual

Thermador Ventilation Hood PH30ZS, PH36ZS, PH42ZS, PH48ZS, PH54ZS, PHI48ZS, PHI60ZS User manual
®
CARE AND USE MANUAL
for
PH and PHI SERIES PROFESSIONAL
WALL and ISLAND HOODS
PH30ZS, PH36ZS, PH42ZS,
PH48ZS, PH54ZS,
PHI48ZS and PHI60ZS
READ AND SAVE THESE INSTRUCTIONS
A special message to Our Customers,
Thank you for buying a Thermador Hood. Please take the time to read and
understand this entire booklet before using your new appliance.
We hope that the information in this manual will help you easily operate and
care for your Hood with years of satisfaction.
Please contact us if you have any questions or comments. Thermador’s address
and phone number are listed on the last page of each language section in this
booklet.
TABLE OF CONTENTS
Important Safety Instructions ......................................................................................... 3
Operating the Hood ............................................................................................................. 4
Hood Control Buttons ......................................................................................................... 5
Care and Cleaning ................................................................................................................ 6
Maintenance ........................................................................................................................... 7
Thermador Hood Warranty ............................................................................................... 8
Retain this manual for future reference.
Note: The Thermador Hood referred to throughout this manual is manufactured by BSH Home Appliances
Corporation.
PAGE 2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
TO REDUCE THE RISK OF INJURY TO PERSONS,
IN THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:
1 . Use this unit only in the manner
intended by the manufacturer. If you
have
questions,
contact
the
manufacturer (800/735-4328).
a ) SMOTHER FLAMES with a close-fitting lid,
cookie sheet, or other metal tray, then turn
off the gas burner or the electric element.
BE CAREFUL TO PREVENT BURNS. If the
flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
2 . Before servicing or cleaning the unit,
switch power off at service panel and
lock ser vice panel. This will prevent
power from being switched on
accidentally. When the service panel
cannot be locked, securely fasten a
prominent warning device, such as a tag
to the service panel.
b ) NEVER PICK UP A FLAMING PAN, you may
be burned.
c) DO NOT USE WATER, including wet dish
cloths or towels - a violent steam explosion
may result.
d ) Use an extinguisher ONLY if:
1 ) You know you have a class ABC
extinguisher, and you already know how
to operate it.
WARNING
FOR GENERAL VENTILATING USE ONLY.
TO AVOID A FIRE OR EXPLOSION
HAZARD DO NOT USE TO EXHAUST
HAZARDOUS OR EXPLOSIVE MATERIALS
OR VAPOR.
2 ) The fire is small and contained in the
area where it started.
3 ) The fire department is being called.
4 ) You can fight the fire with your back to
an exit.
WARNING
TO REDUCE THE RISK OF A RANGE TOP
GREASE FIRE.
1.
Never leave surface units unattended at
high settings. Boilovers cause smoking
and greasy spillovers that may ignite.
Heat oils slowly on low or medium
settings.
2 . Always turn hood ON when cooking on
high heat or when flambéing foods.
3 . Clean ventilating fans frequently. Grease
should not be allowed to accumulate on
fan or filter.
4 . Use proper pan size. Always use
cookware appropriate for the size of the
surface element.
READ AND SAVE THESE INSTRUCTIONS
PAGE 3
OPERATING THE HOOD
The blower should be turned on for about 5 minutes
before cooking in order to establish air currents
upward through the hood. Thus when heat, smoke,
moisture, grease and cooking odors are produced,
they will be carried outside instead of drifting into
other rooms. Use the low speeds for normal use and
the higher speeds for strong odors or fumes.
Drafts across the range or cooktop will reduce the
effectiveness of the hood. Such drafts should be
prevented when possible.
The best job of ventilation in the kitchen is done where
the only air currents are those created by the blower
itself.
CONTROL PANEL FOR WALL HOODS
®
1
OFF
1
2
FAN
SPEED
L
3
DELAY
A
AY
SHUT OFF
4
FILTER
L
LTER
LIGHT
R
HEAT
AT LAMPS
A
Figure 1
CONTROL PANEL FOR ISLAND HOODS
®
1
OFF
2
FAN
SPEED
3
DELAY
A
AY
SHUT OFF
FILTER
L
LTER
LIGHT
Figure 2
Note: The PH Series Wall Hoods come with Heat Lamps. PHI Series Island Hoods do not come with Heat
Lamps.
PAGE 4
HOOD CONTROL BUTTONS
OFF
HEAT SENSOR
Pressing button once turns ventilator off and resets
control.
FAN SPEED
Pressing button once, from an off state, turns the
ventilator on low. Each successive press of the button
increases the fan speed until high where the fan
cycles back to the low speed.
• The LEDs above this button indicate the current
fan speed. When the fan is on, the corresponding
LED is illuminated.
1 – Low
2 – Medium
3 – High
DELAY SHUT OFF
•
Press to turn fan on high for 10 minutes.
If the ventilator is off when the delay button is
pressed, the ventilator will turn on to the high speed
setting for 10 minutes. At the end of the cycle the
ventilator will turn off.
If the ventilator is on when the delay button is
pressed, the ventilator runs for 10 minutes at the
current speed then turns off.
• During a timed period, the LED above the Delay
Shut Off button is illuminated.
• To interrupt a timed period, press Fan Speed or
Off button.
CLEAN FILTER REMINDER
After 40 hours of operation, the clean filter reminder
LED above this button will illuminate indicating that
the filters need to be cleaned. When this indicator
illuminates, clean the filters as instructed on page 6.
After cleaning, press this button for 3 seconds to
reset the 40-hour period and turn the LED off.
Your hood is equipped with a heat sensor that will
turn the blower to Low speed if excessive heat occurs
above the cooking surfaces.
1 . If the blower is off – it turns the blower on to low
speed.
2 . If the blower is already on any speed selection,
no speed change will occur.
When the temperature level on the hood drops to
normal, the blower will return to its original setting.
Over Temperature Condition - The high
temperature sensor protects the hood from high
temperatures which may damage components. The
control is set to activate at 161º F (72º C) and reset
at 140ºF (60º C). When activated, the ventilator will
turn on low and the corresponding LED will blink,
indicating an over temperature condition.
While the high temperature sensor is activated, the
blower speed can be changed or turned off. If the
blower is turned off, the corresponding LED will blink.
Light controls will remain operational. When the
control sensor reaches 140ºF (60º C), a reset will
occur. During reset, the control will revert back to
the operational state prior to the high temperature
condition.
High Temperature Fault Condition - The circuit
is equipped with an alarm indicating that the heat
sensor protection is not working, due to a damaged
sensor. In the case of this extreme condition, the
three speed indicator LEDs will start blinking. All the
controls will be operational except for the speed
indicators.
LIGHT On/Dim/Off
This button controls the halogen lighting. The first
press turns the lights on. A second press dims the
lights. A third press turns the lights off.
HEAT LAMP (for Wall Hoods Only)
The buttons marked “L” and “R” independently control
the left and right infrared heating lamps, turning the
lights on or off.
PAGE 5
CARE AND CLEANING
To Clean Hood Surface
•
•
•
•
•
For general care, wipe the outside of the stainless
steel with sudsy water or household cleaners
such as Fantastic ® or Formula 409 ®, rinse well
and dry with a clean soft cloth to avoid water
marks.
®
Wipe and dry stainless steel in the same direction
as the grain. Avoid using too much pressure,
which may mar the surface.
Do not use abrasive products such as steel wool.
To remove finger prints and give added shine,
use spray cleaners such as Stainless Steel Magic®
and Shimmer ® .
Do not allow any cleaning compounds to remain
in contact with stainless steel for extended
periods.
1
OFF
2
3
DELAY
A
AY
SHUT OFF
FAN
SPEED
LIGHT
FILTER
L
LTER
Figure 3
NOTE: DO NOT USE COOKTOP WHILE
HOOD IS DISASSEMBLED. GREASE
TROUGHS MUST BE IN PLACE BEFORE
INSTALLING THE ALUMINUM FILTERS.
To Clean Filters and Troughs
Your hood has removable aluminum filters, grease
troughs and side panels. They must be cleaned when
the filter light illuminates on the control panel or
whenever they collect the grease. When used over a
grill, wok or other high grease applications, more
frequent cleaning may be required.
To Remove Filters and Grease Troughs:
• Turn the fan and lights off. Be sure filters are
cool and grease has congealed before removal.
• Remove in the following order:
®
1. Filters - Start with center filters, push up, then
pull out from the bottom.
2. Side Panels - Remove these the same way
as the filters.
•
1
1
2
Filters
2
3. Grease Troughs - lift up and out.
The filters can be washed by hand or in the
dishwasher.
Reverse the above directions to reinsert the trough,
filters and side panels.
Side
Panel
Filters
Grease Trough
Note: Depending upon the size and model of hood,
there will be anywhere from 2 to 8 filters per hood.
Figure 4
PAGE 6
Side
Panel
MAINTENANCE
LIGHTS
NOTE: Turn off the lights and fan. Allow the lights
to cool before handling. If new lights do not operate,
be sure lights are inserted correctly before calling
service.
Halogen Light Replacement
(for PH and PHI Model Wall and
Island Hoods)
•
•
Using a flat edge from a screwdriver or equivalent
tool, pry loose the lens cover as shown in Figure
5.
Remove the damaged light and replace with a
new 12 Volt, 20 Watt (maximum) halogen light
made for a G-4 base. Follow package directions
and do not touch new light with bare hands.
•
Reinstall the light and cover.
Figure 5
HEAT LAMP REPLACEMENT
(for PH Wall Hood Models Only)
•
Turn heat lamp counterclockwise to remove.
•
Replace lamp with either a PAR-38 175W heat
lamp or a PAR-40 250W heat lamp.
The PAR-38 175W heat lamp provides a tighter seal
within the enclosure and produces the same amount
of effective heat with lower energy consumption.
These lamps may not be readily available at local
retail outlets. The PAR-40 250W heat lamp is readily
available at local retail outlets.
To order PAR-38 175 heat lamps with a credit card,
phone:
• OpTechInc. 800-848-6624 or
• www.bulbs.com 888-455-2800
Figure 6
CAUTION
DO NOT TOUCH THE BULBS IMMEDIATELY
AFTER USE. THE BULBS WILL REMAIN HOT
FOR SEVERAL MINUTES. DO NOT PLACE
HIGHLY FLAMMABLE MATERIAL ON WARMING
SHELVES.
PAGE 7
THERMADOR HOOD WARRANTY
FULL ONE YEAR WARRANTY
Covers one year from date of installation, or date of occupancy on a new, or previously unoccupied dwelling.
Save your dated receipt or other evidence of installation/ occupancy date.
Thermador Will Pay For:
All repair labor and replacement parts found to be defective due to materials and workmanship.
Service must be provided by a Factory Authorized Service Agency, during normal working hours. For a Service
Agency nearest you, please call 800/735-4328.
Thermador Will Not Pay For:
1 . Service by an unauthorized agency, damage or repairs due to service by an unauthorized agency or the
use of unauthorized parts.
2 . Service visits to:
•
Teach you how to use the appliance.
•
Correct defects or repairs due to improper installation. You are responsible for providing electrical
wiring and other connecting facilities.
•
Reset circuit breakers or replace home fuses.
•
Damage caused from accident, alteration, misuse, abuse, improper installation or installation not in
accordance with local electrical codes or plumbing codes, or improper storage of the appliance.
•
Travel fees and associated charges incurred when the product is installed in a location with limited or
restricted access. (i.e., airplane flights, ferry charges, isolated geographic regions).
•
Repairs due to other than normal home use.
This warranty applies to appliances used in residential applications. These products are not intended for
installations, nor will any warranty apply if they are so used.
The warranty is for products purchased and retained in the 50 states of the U. S. A., the District of Columbia
and Canada. Should the appliance be sold by the original purchaser during the warranty period, the new
owner continues to be protected until the expiration date of the original purchaser’s warranty period. Products
for use in Canada must be purchased through the Canadian distribution channel to ensure regulatory compliance
and warranty coverage
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
HOW TO OBTAIN SERVICE
•
Contact the Factory Authorized Service Agent in your area.
•
Contact the Dealership where you purchased the appliance.
•
Call the Thermador Customer Support Call Center at 800-735-4328.
•
Write us to at:Thermador 5551 McFadden Avenue, Huntington Beach CA, 92649.
®
5551 McFadden Avenue, Huntington Beach, CA 92649 • 800/735-4328
© 2002 BSH Home Appliances, Corp. • Litho in U. S. A.
50 60 00 66 39 (8207)
PAGE 8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement