Sony Cordless Telephone SPP-A9171 User manual

Sony Cordless Telephone SPP-A9171 User manual
3-223-523-11 (1)
Cordless
Telephone
with Answering System
Operating Instructions
SPP-A9171
©2000 Sony Corporation
US
Owner’s Record
The model and the serial numbers are
located at the bottom of the unit. Record
the serial number in the space provided
below. Refer to these numbers
whenever you call upon your Sony
dealer regarding this product.
Model No. SPP-A9171
Serial No. ________________
IMPORTANT
SAFETY
INSTRUCTIONS
When using your telephone equipment,
basic safety precautions should always
be followed to reduce the risk of fire,
electric shock and injury to persons,
including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on the product.
3. Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
4. Do not use this product near water,
for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub, in
a wet basement, or near a swimming
pool.
5. Do not place this product on an
unstable cart, stand, or table. The
product may fall, causing serious
damage to the product.
2US
6. Slots and openings in the cabinet and
the back or bottom are provided for
ventilation. To protect it from
overheating, these openings must not
be blocked or covered. The openings
should never be blocked by placing
the product on the bed, sofa, rug, or
other similar surface. This product
should never be placed near or over a
radiator or heat register. This product
should not be placed in a built-in
installation unless proper ventilation
is provided.
7. This product should be operated only
from the type of power source
indicated on the marking label. If you
are not sure of the type of power
supply to your home, consult your
dealer or local power company.
8. Do not allow anything to rest on the
power cord. Do not locate this
product where the cord will be abused
by persons walking on it.
9. Do not overload wall outlets and
extension cords as this can result in
the risk of fire or electric shock.
10. Never push objects of any kind into
this product through cabinet slots as
they may touch dangerous voltage
points or short out parts that could
result in a risk of fire or electric shock.
Never spill liquid of any kind on the
product.
11. To reduce the risk of electric shock,
do not disassemble this product, but
take it to a qualified service personnel
when some service or repair work is
required. Opening or removing
covers may expose you to dangerous
voltages or other risks. Incorrect
reassembly can cause electric shock
when the appliance is subsequently
used.
12. Unplug this product from the wall
outlet and refer servicing to qualified
service personnel under the following
conditions:
A. When the power cord or plug is
damaged or frayed.
B. If liquid has been spilled into the
product.
C. If the product has been exposed to
rain or water.
D. If the product does not operate
normally by following the operating
instructions. Adjust only those
controls that are covered by the
operating instructions because
improper adjustment of other controls
may result in damage and will often
require extensive work by a qualified
technician to restore the product to
normal operation.
E. If the product has been dropped or
the cabinet has been damaged.
F. If the product exhibits a distinct
change in performance.
13. Avoid using a telephone (other than
a cordless type) during an electrical
storm. There may be a remote risk of
electric shock from lightning.
14. Do not use the telephone to report a
gas leak in the vicinity of the leak.
SAVE THESE
INSTRUCTIONS
CAUTION:
To reduce the risk of fire or injury to persons by
battery, read and follow these instructions.
1. Use only the following type and size battery
pack: Sony BP-T31.
toxic if swallowed.
4. Exercise care in handling battery pack in
order not to short the battery with conducting
materials such as rings, bracelets, and keys.
The battery or conductor may overheat and
cause burns.
5. Charge the battery pack provided with or
identified for use with this product only in
accordance with the instructions and
limitations specified in the instruction manual
provided for this product.
6. Observe proper polarity orientation between
the battery pack and battery charger.
INFORMATION FOR
GENERAL TELEPHONES
1. This equipment complies with Part 68 of the
FCC rules. On the bottom of this equipment
is a label that contains, among other
information, the FCC certification number and
ringer equivalence number (REN) for this
equipment. If requested, this information
must be provided to the telephone company.
2. The applicable certification jack (connector)
USOC-RJ11C is used for this equipment.
3. This equipment is designed to be connected to
the telephone network or premises wiring
using a compatible modular jack that is Part
68 compliant.
The FCC compliant telephone cord and
modular plug is provided with this
equipment.
4. The REN is used to determine the quantity of
devices that may be connected to the
telephone line. Excessive RENs on the
telephone line may result in the devices not
ringing in response to an incoming call.
Typically, the sum of the RENs should not
exceed five (5.0).To be certain of the number
of devices that may be connected to a line, as
determined by the total RENs, contact the
local telephone company.
5. If this equipment (SPP-A9171) causes harm to
the telephone network, the telephone
company will notify you in advance that
temporary discontinuance of service may be
required. But if advance notice isn’t practical,
the telephone company will notify the
customer as soon as possible. Also, you will
be advised of your right to file a complaint
with the FCC if you believe it is necessary.
2. Do not dispose of the battery pack in a fire.
The cell may explode. Check with local codes
for possible special disposal instructions.
3. Do not open or mutilate the battery pack.
Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be
3US
6. The telephone company may make changes in
its facilities, equipment, operations or
procedures that could affect the operation of
the equipment. If this happens the telephone
company will provide advance notice so you
can make necessary modifications to maintain
uninterrupted service.
7. If trouble is experienced with this equipment
(SPP-A9171), for repair or warranty
information, please contact Sony Direct
Response Center: Tel 1-800-222-7669. If the
equipment is causing harm to the telephone
network, the telephone company may request
that you disconnect the equipment until the
problem is resolved.
8. All repairs will be performed in an authorized
Sony service station.
9. This equipment cannot be used to party lines
or coin lines.
Note
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
10.This equipment is hearing aid compatible.
If your telephone is equipped
with automatic dialers
When programming emergency numbers and
(or) making test calls to emergency numbers:
1. Remain on the line and briefly explain to
the dispatcher the reason for the call.
2. Perform such activities in the off-peak
hours, such as early morning or late
evenings.
Caution
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
4US
– Reorient or relocate the receiving antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/
TV technician for help.
Table of contents
Getting Started
6 Read this first
7 Step 1: Checking the package
contents
8 Step 2: Setting up the base unit
11 Step 3: Preparing the battery pack
14 Step 4: Entering the area code
17 Changing the language of the
display and the voice guidance
18 Identifying the parts
41
43
45
46
47
49
49
50
Basics
22 Making calls
24
Redialing
25 Receiving calls
Telephone Features
26 One-touch dialing
26
Storing phone numbers
27
Making calls with one-touch
dialing
28 Phone Directory
28
Storing phone numbers and
names
29
Changing a stored name
and/or phone number
30
Erasing a memory location
31
Making calls from the Phone
Directory
32 Paging
Answering Machine Features
33 Preparing the answering machine
33
Setting the day and time
35
Recording the greeting
38
Selecting the ring time
39
Selecting the recording
quality
40
Selecting the answering
mode
Turning on the answering
function
Playing back messages
Erasing messages
Screening incoming calls
Recording a memo
Operating from an outside
phone
Setting the remote ID code
(security code)
Picking up new messages
Caller ID Features
51 Understanding the Caller ID
service
51
When you receive a call
52 Looking at the Caller ID list
52
Viewing the Caller ID list
53
Erasing data from the
Caller ID list
55 Using the Caller ID list
55
Calling back a number from
the Caller ID list
56
Storing a number of the
Caller ID list into the Phone
Directory
57
To change the number of
digits of the phone number
59 Using “Caller ID with call
waiting” service
Additional Information
60
61
62
63
68
69
Mounting the base unit on a wall
Notes on power sources
Maintenance
Troubleshooting
Specifications
Index
Back cover LIMITED WARRANTY
Table of contents
5US
Getting Started
Read this first
Before you use your phone, you must set it up. Here’s a quick way to
set up your phone: Steps 1, 2, 3 and 4.
Step 1
(page 7)
First, unpack the phone and the supplied
accessories.
Step 2
(pages 8 to 10)
Next, you need to do three things to set
up the base unit, including finding the
best location for the base unit.
Base unit
Step 3
(pages 11 to 12)
Then, you need to insert the battery
pack into the handset and charge it for
more than 12 hours.
Step 4
(pages 14 to 16)
Finally, you need to enter the area code
to use the Caller ID service.
Handset
That’s it!
If you want to change the language of the display and the
voice guidance, follow the procedure in “Changing the
language of the display and the voice guidance” on page
17.
6US
Getting Started
Step 1
Checking the package contents
Make sure you have received the following items in the package.
If anything is missing, contact your local Sony dealer.
Getting Started
AC power adaptor (AC-T46)
Telephone line cords (2)
Base unit
Wall bracket/stand
for base unit
Handset
Rechargeable battery
pack (BP-T31)
Getting Started
7US
Step 2
Setting up the base unit
Do the following steps:
• Choose the best location
• Connect the base unit
• Choose the dialing mode
Choose the best location
Where you place the base unit affects the reception quality of the
handset.
Away from noise sources such as a window
by a street with heavy traffic
Away from television
sets and other
electronic equipment
Away from heat sources, such as radiators,
airducts, and sunlight
Away from a microwave
oven
Away from excessive
moisture, extremely low
temperatures, dust,
mechanical vibration, or
shock
Away from a personal
computer
Near a central location
and on a level surface
Away from another
cordless telephone
CAUTION: • Should you experience intermittent loss of audio during a conversation, try
moving closer to the base or move base unit away from other noise sources.
• The cordless telephone operates at a frequency that may cause interference to
nearby TVs and VCRs; the base unit should not be placed near or on the top of
a TV or VCR; and, if interference is experienced, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate the
interference.
8US
Getting Started
Connect the base unit
If you want to hang the base unit on the wall, see page 60.
4
Display
Getting Started
Hook the cord.
To AC outlet
To DC IN 9V
3
AC power adaptor
(supplied AC-T46)
1
Align the f
marks.
To LINE
To
telephone
outlet
2 Telephone line cord
2
1
(supplied)
1 Attach the wall bracket to the
bottom of the base unit as
illustrated to use it as a stand.
2 Connect the telephone line cord
to the LINE jack and to a
telephone outlet.
3 Connect the AC power adaptor
to the DC IN 9V jack and to an
AC outlet.
“P” flashes on the display.
4 Raise the antenna. Make sure it
points toward the ceiling.
continued
Getting Started
9US
Step 2: Setting up the base unit (continued)
Notes
• Use only the supplied AC-T46 AC power adaptor.
Do not use any other AC power adaptor.
• Connect the AC power adaptor to a continuous power
supply.
• Place the base unit close to the AC outlet so that you
can unplug the AC power adaptor easily.
Polarity of the plug
–
Tip
If your telephone outlet is not modular, contact your
telephone service company for assistance.
+
Modular
Choose the dialing mode
For the telephone to work properly, select an appropriate dialing mode
(tone or pulse).
DIAL MODE switch
Depending on your dialing system, set the DIAL MODE switch as
follows:
If your dialing system is
Set the switch to
Tone
T
Pulse
P
If you aren't sure of your dialing system
Make a trial call with the DIAL MODE switch set to T.
If the call connects, leave the switch as is; otherwise, set to P.
10US
Getting Started
Step 3
Preparing the battery pack
Charge the battery pack for more than 12 hours before you start using
your phone.
compartment lid of the handset.
2 Insert the battery pack into the
BP-T31
battery compartment.
Getting Started
1 Slide open the battery
3 Close the battery compartment
lid.
4 Place the handset on the base
unit.
You can place either side facing
up.
The CHARGE lamp lights up
when the handset is properly
seated on the charge terminals
of the base unit. Charge the
battery pack for more than 12
hours so that the battery is fully
charged. The CHARGE lamp
remains lit even after charging
is completed.
continued
CHARGE lamp
Getting Started
11US
Step 3: Preparing the battery pack (continued)
Battery duration
A fully charged battery pack lasts for about:
• Approx. 6 hours when you use the handset continuously
• Approx. 7 days when the handset is in standby mode.
Notes
• The battery pack will gradually discharge over a long period of time, even if
not in use.
• If you leave the battery pack in the handset without charging it, the battery
pack will be completely discharged.
It may require several times of charging to recover to its full capacity.
• While charging, the battery pack warms up. This is not a malfunction.
To obtain the best performance from the battery
Do not place the handset on the base unit after each call. The battery
works best if the handset is returned to the base unit after two or three
calls. However, do not leave the handset off the base unit for a long
period of time as this will completely discharge the battery pack.
When to purchase a new battery pack
If the battery lasts only a few minutes even after 12 hours of charging,
the usable life of the battery has expired and needs replacement.
Contact your local Sony authorized dealer or service center, and ask
for Sony BP-T31 rechargeable battery pack.
Note
Battery life may vary depending on usage condition and ambient temperature.
12US
Getting Started
Handset spare battery usage
As only one battery pack is supplied with this unit, it is necessary to
purchase an additional battery pack (optional) for use as a handset
spare battery pack.
lid of the base unit.
Getting Started
1 Open the battery compartment
2 Insert the battery pack
BP-T31
(optional) into the battery
compartment.
3 Close the battery compartment
lid.
The SPARE BATTERY lamp
lights up. Charge the battery
pack for more than 24 hours so
that the battery is fully charged.
The SPARE BATTERY lamp
remains lit even after charging
is completed.
SPARE BATTERY
lamp
Getting Started
13US
Step 4
Entering the area code
When you use this phone for the first time, or move to an area
that has a different area code, you must enter the area code.
Otherwise, you cannot use some functions of this phone and the
Caller ID functions.
This is also necessary because the phone must be able to select an
area code to properly dial call from the Caller ID list.
Depending on your region, enter 3-digit area code as follows:
Case 1.
If 7-digit dialing (no area code) is accepted for local calls in your area,
see “To enter your home area code” below.
If you live in an area where calls from or to other local areas can also be made
by 10-digit dialing (area code + number), you can register up to 5 local area
codes with this telephone to take advantage of this system. See “To enter the
local area code (For 10 digits phone number users)” on page 15.
Case 2.
If 10-digit dialing (area code + number) is required for all local calls in
your area, see “To enter the local area code (For 10 digits phone
number users)” on page 15.
To enter your home area code
Turn
Press
1 Press (PGM).
2 Turn Jog Dial down to make “HOME
AREA CODE” flash.
HOME AREA CODE
LOCAL AREA CODE
3 Press Jog Dial.
“ENTER AREA CODE” appears on
the display.
ENTER AREA CODE
4 Enter the three digits of your home
area code using the dialing keys.
5 Press (PGM).
14US
Getting Started
You hear a long confirmation beep.
Notes
• If the home area code is already entered, it appears on the display in step 3. To
enter a different home area code, see “To change the home area code” below.
• Do not allow more than 20 seconds to elapse during the operation procedure.
• If the area code has not been entered, calling back from the Caller ID list and
storing the Caller ID data into the Phone Directory cannot be performed.
Getting Started
Tips
• You may press Jog Dial instead of (PGM) in step 5.
• To check the current home area code, perform steps 1 to 3. The home area code
appears on the display for about 20 seconds.
To change the home area code
Perform steps 1 to 3 on page 14.
1
The current home area code appears on the display.
2
3
4
Turn Jog Dial down to erase the current home area code.
Enter a new home area code using the dialing keys.
Press (PGM).
You hear a long confirmation beep.
To erase the home area code
You can erase the home area code. Perform steps 1 and 2 above, then press
(PGM).
The home area code will be erased, and you hear a long confirmation beep.
To enter the local area code (For 10 digits
phone numbers users)
If a call matches one of the local area codes you entered, the phone number
will be registered with 10 digits in the Caller ID list (area code + number).
If a call does not match one of the local area codes you entered, the phone
number will be registered with 11 digits in the Caller ID list (1 + area code
+ number). Some regions of the country allow you to have more than one
local area code. (Up to five local area codes can be entered in this phone.)
1
2
Press (PGM).
Turn Jog Dial down to make “LOCAL AREA
CODE” flash.
LOCAL AREA CODE
ONE-TOUCH A
3
Press Jog Dial.
#1 #2 #3 #4 #5
continued
Getting Started
15US
Step 4: Entering the area code (continued)
4
Select the number (”#1“ to ”#5“) to enter the local area code
by turning Jog Dial.
5
Press Jog Dial.
”ENTER AREA CODE“ appears on the display.
6
Enter the three digits of the local area code using the dialing
keys.
7
Press (PGM).
You hear a long confirmation beep.
Notes
• If the local area code is already entered, it appears on the display in step 4. To
enter a different local area code, see “To change the local area code” below.
• Do not allow more than 20 seconds to elapse during the operation procedure.
Tips
• You may press Jog Dial instead of (PGM) in step 7.
• To check the current local area code, perform steps 1 to 4. The local area code
appears on the display for about 20 seconds.
To change the local area code
Perform steps 1 to 5 on pages 15 to 16.
1
The current local area code appears on the display.
2
3
4
Turn Jog Dial down to erase the current local area code.
Enter a new local area code using the dialing keys.
Press (PGM).
You hear a long confirmation beep.
To erase the local area code
You can erase the local area code. Perform steps 1 and 2 above, then
press (PGM).
The local area code will be erased, and you hear a long confirmation
beep.
16US
Getting Started
Changing the language of the display
and the voice guidance
You can choose English or Spanish as the display and the voice guidance language by
following the procedure below.
To change the language from Spanish to English
Press
1 Press (PGM).
2 Turn
Jog Dial down to make
“ELEGIR IDIOMA” flash, and
then press Jog Dial.
ENGLISH ESPA OL
3 Press Jog Dial.
Getting Started
Turn
ENGLISH NO YES
4 Select
“YES” by turning Jog Dial
to change the language, and
then press Jog Dial.
You will hear a long
confirmation beep.
5 Replace
the handset on the base
unit.
To change the language from English to Spanish
1
2
Press (PGM).
3
Select “ESPAÑOL” by turning Jog Dial, and
then press Jog Dial.
4
Select “SÍ” by turning Jog Dial to change the
language, and then press Jog Dial.
Turn Jog Dial down to make “LANGUAGE
SELECT” flash, and then press Jog Dial.
ESPA OL NO S
You will hear a long confirmation beep.
5
Replace the handset on the base unit.
Note
Do not allow more than 20 seconds to elapse during the operation procedure.
Getting Started
17US
Identifying the parts
Refer to the pages indicated in parentheses for details.
Base Unit
1
2
3
4
5
6
7
qs
qd
qf
qg
qh
qj
8
9
0
qa
qk
ql
w;
1 ERASE button (p. 37, 45)
Erases the recorded greeting or
messages.
2 MEMO button (p. 47)
Records a memo message.
3 GREETING REC button (p. 35)
Press to record a greeting.
4 GREETING PLAY button (p. 37)
Plays back the greeting message.
5 NEW CALL lamp (p. 52)
Flashes when there is a “NEW”
data in the Caller ID list.
6 . REPEAT/REVIEW button
(p. 44)
Press to repeat the current message
or go back to the previous message.
Keep the button pressed for a
playback review of the current
message.
7 Battery compartment (p. 13)
8 SPARE BATTERY lamp (p. 13)
Lights while the spare battery is
being charged.
18US
Getting Started
9 CHARGE lamp (p. 11)
Lights while the battery is being
charged.
0 IN USE lamp (p. 22)
Lights when the handset is in use.
qa MIC (microphone) (p. 35, 47)
qs Antenna (p. 9, 60)
qd Speaker
qf Display (p. 19, 43)
qg TIME button (p. 34)
Press to check the current time.
qh ANSWER ON/OFF button (p. 41)
Turns the answering function on or
off. Lights when the answering
function is on, and flashes when a
new message is recorded.
qj VOLUME +/– buttons (p. 44)
Adjusts the speaker volume.
qk > SKIP/QUICK button (p. 44)
Press to skip to the next message.
Keep the button pressed for quick
playback of messages.
Display
The display on the base unit shows the
answering machine operation.
1
wdwf
3
4
Getting Started
wa ws
2
wgwhwj
ql HANDSET LOCATOR button
(p. 32)
Allows you to page the handset.
w; PLAY/STOP (MAILBOX 1, 2, 3)
buttons (p. 43)
Plays back the messages in each
mail box.
wa DIAL MODE switch (p. 10)
Selects pulse or tone dialing.
ws Hook for AC power adaptor
cord (p. 9)
wd DC IN 9V jack (p. 9)
wf LINE (telephone line) jack
(p. 9)
wg AUDIBLE INDICATOR switch
(p. 40)
Selects the answering mode.
wh REC. QUALITY switch (p. 39)
Selects the recording quality.
wj RINGER SELECT switch (p. 38)
1 Memory capacity indicator
(p. 40)
Indicates the available memory
capacity, fromE (Empty) to F (Full),
for recording. The bars increase as
the available memory capacity
decreases.
2 MAILBOX indicator (p. 43)
Displayed when there are messages
recorded and when the messages
are being played back.
“NEW” flashes when there are new
messages recorded.
3 Message counter (p. 43)
Indicates the number of new
messages recorded. “A” appears in
the announcement only mode. “F”
appears when there is no space to
record messages. “P” appears when
the power is turned on.
4 VOL (volume) indicator
Indicates the speaker volume. The
bars increase as the volume is
turned up.
Selects the ring time.
continued
Getting Started
19US
Identifying the parts (continued)
Handset
1
2
qf
3
4
5
6
7
8
9
0
qa
qs
qg
qh
qj
qk
ql
w;
wa
ws
qd
1 Antenna
2 Speaker [EZfit] (p. 23)
8 PGM (Program) button
(p. 14, 26, 28)
Used to store numbers for onetouch dialing or in Phone Directory.
3 OFF button (p. 22)
Allows you to disconnect the call.
9 REVIEW button (p. 44)
4 Jog Dial (p. 14, 26, 52)
Keep the button pressed for a
playback review of the current
message.
5 TALK button (p. 22)
Lets you make or receive a call.
6 REMOTE button (p. 33)
Used to display the answering
machine function menu.
7 . REPEAT button (p. 44)
Press to repeat the current message
or go back to the previous message.
0 Dialing keys (p. 22)
qa
TONE button (p. 22)
Allows you to switch temporarily to
tone dialing.
qs Battery compartment (p. 11)
qd RING switch (p. 25)
Switches the ringer to on/off.
20US
qf Display (p. 51)
Getting Started
Getting Started
wd
qg CALL WAITING/FLASH button
(p. 22, 25, 59)
Switches to a second call if you
have “call waiting” service, or lets
you make a new call.
qh REDIAL/PAUSE button
(p. 24, 27)
Redials the last number called/
inserts a pause in the dialing
sequence.
qj > SKIP button (p. 44)
Press to skip to the next message.
qk QUICK button (p. 44)
ql ERASE button (p. 37, 45)
Erases the recorded greeting or
messages.
w; # button (p. 57)
Used to change the number of
digits of the phone number in the
Caller ID list.
wa Microphone
ws ONE-TOUCH DIAL (A, B, C)
buttons (p. 27)
wd VOL (volume) switch (p. 25)
Adjust the handset volume.
Keep the button pressed for quick
playback of messages.
Getting Started
21US
Basics
Making calls
1 Pick up the handset from the
base unit.
2 Press (TALK) and wait until
“TALK” appears on the display.
The display also shows the talk
time in hours, minutes and
seconds.
VOL switch
(CALL WAITING/FLASH)
(REDIAL/PAUSE)
The dialing keys light up.
The IN USE lamp on the base
unit lights up.
(*TONE)
You then hear a dial tone. If you
hear five short error beeps and
“OUT OF RANGE” appears on
the display, move closer to the
base unit.
3 Dial the phone number.
4 When you’re done talking, press
(OFF) or replace the handset on
the base unit.
The display turns off.
Additional tasks
To
Do this
Adjust the handset volume
Set the VOL switch to H (high), M (middle)
or L (low).
Switch to tone dialing temporarily Press (*TONE) after you’re connected.
The line will remain in tone dialing until
disconnected.
Switch to another call
(“call waiting” service*)
Press (CALL WAITING/FLASH).
Press (CALL WAITING/FLASH) again to
return to the first caller.
* You need to subscribe to this service from your telephone company.
22US
Basics
Notes
• When you increase the sound volume, in some cases the background noise
may be increased as well. You should adjust the volume accordingly.
• If the handset beeps every second during conversation and “OUT OF
RANGE” appears on the display, move closer to the base unit; otherwise, the
call will be disconnected after one minute.
• While the base unit is in use, you cannot make a call with the handset. If you
press (TALK), “BASE UNIT IN USE” appears on the display and you will
hear a busy tone.
EZfit
Basics
The “EZfit” adjusts to fit any shape ear,
thereby ensure clear voice reception.
If the battery becomes weak during a call
The handset will beep twice per second, E and “BATTERY LOW”
appear on the display. Finish your call and charge the battery pack.
For optimum performance, charge the battery for a full 12 hours.
Note that during the initial charge time (approx. 10 minutes), E and
“BATTERY LOW” appear on the display and the phone cannot be
used.
After E and “BATTERY LOW” go off, you may be able to use the
phone, but the battery duration will be very short; thus it is
recommended that you fully charge the battery before next use.
continued
Basics
23US
Making calls (continued)
Redialing
1
2
Press (TALK) and wait until “TALK” appears on the display.
Press (REDIAL/PAUSE) to redial the number last dialed.
Note
If the number exceeds 32 digits, five short error beeps will alert you that the
number cannot be dialed.
To check the phone number before redialing
While the handset is not in use, press (REDIAL/PAUSE).
The number last dialed is displayed for 20 seconds.
To dial the number, press (TALK) while the number is displayed.
Note
The number will not be displayed if the last dialed number exceeds 32 digits or
if it is erased.
To erase the last phone number dialed
While the handset is not in use, press (REDIAL/PAUSE) twice.
The number will be erased from the memory, and you will hear a long
confirmation beep.
24US
Basics
Receiving calls
1 When you hear the phone ring,
pick up the handset from the
base unit, and press (TALK) .
“TALK” appears on the display
and the display also shows the
talk time in hours, minutes and
seconds.
(OFF) or replace the handset on
the base unit.
(CALL WAITING/FLASH)
The display turns off.
Basics
2 When you’re done talking, press
Tip
If you have subscribed to the Caller ID service;
• the caller’s number and/or name appears on the display when you receive a
call (see page 51)
• the ringer sound changes to a higher tone if the call matches the number
stored on ONE-TOUCH DIAL buttons or in the Phone Directory (memory
match function; see page 51).
To switch to another call (“call waiting” service*)
Press (CALL WAITING/FLASH).
Press the button again to get back to the first caller.
* You need to subscribe to the service from your telephone company.
To turn the ringer off
Set the RING switch on the bottom to OFF.
The handset won’t ring. You can still make calls, and
also receive calls if another telephone connected to
the same line rings to inform you on incoming calls.
You can also page the handset from the base unit.
RING switch
Basics
25US
Telephone Features
One-touch dialing
You can dial with one touch of a key by storing a phone number on a one-touch
dialing button.
Storing phone numbers
Turn
Press
1 Press (PGM).
2 Turn Jog Dial down to make
“ONE-TOUCH A” to “ONETOUCH C” flash.
ONE-TOUCH A
ONE-TOUCH B
3 Press Jog Dial.
(REDIAL/PAUSE)
You hear a confirmation beep.
A=
ONE-TOUCH DIAL
buttons
If a number is stored, it appears on
the display. To store a new number,
turn Jog Dial down to erase it.
4 Enter the phone number you want
to store.
You can enter up to 20 digits,
including a tone and a pause, each
of which is counted as one digit.
When the phone number of 17
digits or more has been entered, the
phone number appears in two lines.
1234567890123456
12
5 Press (PGM).
You hear a long confirmation beep,
and the number is stored.
The display turns off.
26US
Telephone Features
Note
Do not allow more than 20 seconds to elapse during the operation procedure.
Tips
• When the phone number of 17 digits or more has been entered, “–” is displayed
next to 15th digit in step 5.
• If you have entered a wrong number in step 4 and have not pressed (PGM)
(step 5) yet, just turn Jog Dial down to erase it. Then enter the correct number.
• You may press Jog Dial instead of (PGM) in step 5.
To store a number to be dialed via Private Branch Exchange
(PBX)
Before entering a phone number in step 4 on page 26, do as follows:
1
2
Enter the outside line access digit (e.g., 9).
Press (REDIAL/PAUSE).
The current number appears on the display.
2
3
4
Turn Jog Dial down to erase the current number.
Enter a new number.
Press (PGM).
Note
You can replace the stored number with a new number, but you cannot just erase it.
Telephone Features
To change a stored number
1 Perform steps 1 to 3 on page 26.
Making calls with one-touch dialing
1
2
Press (TALK) and wait until “TALK” appears on the display.
Press one of the ONE-TOUCH DIAL buttons ((A) to (C)).
The phone number stored on the one-touch dialing button will
appear on the display and will be dialed.
To check the phone number before one-touch dialing
While the handset is not in use, press one of the ONE-TOUCH DIAL
buttons ((A) to (C)).
The number stored on the button appears on the display for 20 seconds. To
dial the number, press (TALK) while the number is displayed.
Tip
When the phone number of 17 digits or more has been entered, “–” is displayed next
to 15th digit and then the all digits are displayed in two lines after about two
seconds.
Telephone Features
27US
Phone Directory
You can dial a number by scrolling through the Phone Directory.
You can store up to 100 numbers.
Storing phone numbers and names
Example: to store “SONY” “123-4567”.
Turn
Press
1 Press (PGM).
PHONE DIRECTORY
HOME AREA CODE
2 Press Jog Dial.
“ENTER NAME” appears.
3 Enter the name using the dialing
keys. You can enter up to 15
characters.
Press a dialing key until the desired
character appears. (See the
character table for details.)
Character table
28US
Key
Character
(1)
1
(2)
AtBtCt2
(3)
DtEtFt3
(4)
GtHtIt4
(5)
JtKtLt5
(6)
MtNtOt6
(7)
PtQtRtSt7
(8)
TtUtVt8
(9)
WtXtYtZt9
(0)
0
(*)
*
(#)
&t’t,t–t.t#
Telephone Features
Enter successive characters in the
same way.
To enter two characters assigned to
the same key, or to enter a “space”,
turn Jog Dial up to move the cursor
to the right.
Example: to enter “SONY”, press
(7) four times (S), press (6) three
times (O), turn Jog Dial up to move
the cursor, press (6) twice (N), and
press (9) three times (Y).
SONY
4 Press (PGM).
“ENTER NUMBER” appears.
5 Enter the phone number.
You can enter up to 20 digits, including a tone
and a pause, each of which is counted as one
digit.
When the phone number of 17 digits or more
has been entered, the phone number appears in
two lines.
SONY
1234567
1234567890123456
12
6 Press (PGM).
Telephone Features
You hear a long confirmation beep, and the
name and the number are stored. The display
turns off.
Notes
• If you try to save a 101st phone number, you will hear five short error beeps
and “MEMORY FULL” will be displayed. You cannot store the phone
number. To store another phone number, erase one of the stored phone
numbers (see page 30).
• Do not allow more than 20 seconds to elapse during the operation procedure.
Tips
• When the phone number of 17 digits or more has been entered, “–” is
displayed next to 15th digit in step 6.
• If you have entered a wrong name or number in step 3 or 5, turn Jog Dial
down to erase it. Then enter the correct name or number.
• You may press Jog Dial instead of (PGM) in steps 4 and 6.
• To store a number to be dialed via PBX, follow the steps on page 27 when
entering a phone number.
Changing a stored name and/or phone number
1
Display the name and phone number you want
to change by doing steps 1 and 2 on page 31.
SONY
1234567
2
Press Jog Dial.
DIAL EDIT ERASE
1234567
continued
Telephone Features
29US
Phone Directory (continued)
3
Turn Jog Dial up to make “EDIT” flash and
press Jog Dial.
The cursor flashes at the last character of the
name.
4
Turn Jog Dial down to erase the characters and
enter the new name.
If you want to change only the number, skip this
step.
5
Press Jog Dial.
The cursor flashes at the last digit of the phone
number.
6
Turn Jog Dial down to erase the number and
enter the new number.
If you don’t want to change the number, skip
this step.
7
Press Jog Dial.
You hear a long confirmation beep and the
name and/or the number is changed.
SONY
1234567
SONY
1234567
Tip
When the phone number of 17 digits or more has been entered, “–” is displayed
next to 15th digit and then the all digits are displayed in two lines after about
two seconds.
Erasing a memory location
30US
1
Display the name and phone number you want
to erase by doing steps 1 and 2 on page 31.
SONY
1234567
2
Press Jog Dial.
DIAL EDIT ERASE
1234567
3
Turn Jog Dial up to make “ERASE” flash and
press Jog Dial.
ERASE NO YES
1234567
4
Turn Jog Dial up to make “YES” flash, then
press Jog Dial.
You hear a long confirmation beep and the
memory location is erased.
Telephone Features
Making calls from the Phone Directory
Turn
1 Press Jog Dial.
Press
“PHONE DIRECTORY” appears on
the display.
2 Display the name and phone number
you want to call.
To search in alphabetical order:Turn
Jog Dial up or down.
To search by entering the initial
character:Press the dialing key of the
desired character, then turn Jog Dial.
Telephone Features
SONY
1234567
3 Press Jog Dial.
DIAL EDIT ERASE
1234567
4 Press Jog Dial again.
The phone number will be dialed.
Tips
• You may press (TALK) to make a call instead of doing steps 3 and 4.
• When the phone number of 17 digits or more has been entered, “–” is
displayed next to 15th digit and then the all digits are displayed in two lines
after about two seconds.
About the search order
The names appear in the following order when you turn Jog Dial up or
down.
t
t
• Alphabetical order: ABC...XYZ y symbols y * y # y 0 - 9
• Initial character: To search for “SONY” for example, press (7) and
then turn Jog Dial to search through the names starting with P, Q, R,
S or 7.
Telephone Features
31US
Paging
You can page the handset from the base unit.
Note that you cannot page if the handset is in use.
To Page
Press (HANDSET LOCATOR).
The handset rings for about one
minute.
To stop ringing, press (TALK) or
(OFF) on the handset.
Tip
You can page the handset even when its RING switch is set to OFF.
32US
Telephone Features
Answering Machine Features
Preparing the answering machine
Setting the day and time
Set the day and time so that you can stamp day and time for the
incoming messages. You’ll hear the recorded day and time when you
play back messages.
Setting the day and time is only possible on the handset.
Turn
1 Press (REMOTE) and wait until
the answering machine function
menu appears on the display.
Press
PLAY MAILBOX 1
PLAY MAILBOX 2
(OFF)
If you hear five short error
beeps and “OUT OF RANGE”
appears on the display, move
closer to the base unit.
“SET DAY & TIME” flash, and
then press Jog Dial.
SET DAY & TIME
SUNDAY
3 Set the correct day of the week
by turning Jog Dial, and then
press Jog Dial.
SET DAY & TIME
SUNDAY
Answering Machine Features
2 Turn Jog Dial down to make
continued
Answering Machine Features
33US
Preparing the answering machine (continued)
4 Set the hour (1 to 12) and choose “AM” or
“PM” by turning Jog Dial, and then press Jog
Dial.
SET DAY & TIME
SUNDAY
5 Set the minute (00 to 59) by turning Jog Dial,
and then press Jog Dial.
You hear a long confirmation beep. Then the
phone starts counting time.
6 Press (OFF).
Notes
• Do not allow more than 20 seconds (or 60 seconds when setting the minute)
to elapse during the operation procedure.
• If a power interruption occurs, the day and time will be erased.
(TIME)
To check the current time
Press (TIME) on the base unit. You hear the
current day and time.
If you want to check the current time with
the handset, perform steps 1 and 2 on page
33. The current day and time appear on the
display.
Note
If the current day and time are not set, you will not hear a time stamp when you
play back recorded messages. If you try to check the current time with the base
unit, you will hear five short error beeps.
34US
Answering Machine Features
Recording the greeting
This answering machine has prerecorded greetings (see page 37).
However, you can record your own greeting.
The greeting must be between two seconds and four minutes long.
You can record only one greeting, and it is used regardless of the
answering mode (“normal” and “announcement only” modes. See
page 40). Therefore, if you decide to change the mode, make sure that
you record a new greeting to match the answering mode.
You can record the greeting on both the base unit and the handset.
1 Press (GREETING REC).
(GREETING PLAY)
(ERASE)
You hear a voice guidance and a
long confirmation beep.
2 After the tone, start recording.
Speak about 12 inches (30 cm)
away from the microphone.
3 Press (PLAY/STOP) to stop
recording.
The phone automatically
replays the recorded greeting.
Notes
• If recording did not succeed, you hear five short error beeps. Start over the
procedure.
• If a call comes in while recording a greeting, recording is cancelled. Start over
the procedure.
• If you hear five short error beeps while recording, the recording area may be
full. In this case, erase unnecessary messages (see page 45).
• You cannot operate the base unit while the handset is in use.
• This answering machine begins to record the greeting when it detects voice.
Note that recording does not begin if the voice is extremely low or there
is no sound.
Answering Machine Features
MIC (Microphone)
Tips
• If four minutes have passed in step 3, recording stops automatically.
• To record the greeting from a touch-tone phone, see page 50.
continued
Answering Machine Features
35US
Preparing the answering machine (continued)
To record the greeting from the handset
Turn
1 Press (REMOTE) and wait until
the answering machine function
menu appears on the display.
Press
If you hear five short error
beeps and “OUT OF RANGE”
appears on the display, move
closer to the base unit.
(OFF)
ERASE (9)
PLAY MAILBOX 1
PLAY MAILBOX 2
2 Turn Jog Dial down to make
“REC GREETING” flash, and
then press Jog Dial.
REC GREETING
START CANCEL
3 Press Jog Dial.
You hear a long confirmation
beep.
4 After the tone, start recording.
Speak into the handset.
NOW RECORDING
COMPLETE CANCEL
5 Press Jog Dial to stop recording.
You hear a long confirmation
beep and the phone
automatically replays the
recorded greeting.
6 Press (OFF).
36US
Answering Machine Features
Notes
• Do not allow more than 20 seconds to elapse between steps 1 and 2 of the
procedure.
• If recording did not succeed, you hear five short error beeps. Start over the
procedure.
• If a call comes in while recording a greeting, recording is cancelled. Start over the
procedure.
• If you hear five short error beeps while recording, the recording area may be full.
In this case, erase unnecessary messages (see page 45).
Tips
• If four minutes have passed in step 4, recording stops automatically.
• If you want to cancel recording, turn Jog Dial up to make “CANCEL” flash, then
press Jog Dial in step 4.
• To record the greeting from a touch-tone phone, see page 50.
Prerecorded greeting
Normal mode:
“Hello, I’m unable to answer your call right now. Please
leave your name, number and message after the tone.”
Announcement only mode: “Hello, I’m unable to answer your call right now. Please
call again. Thank you.”
Answering Machine Features
Tips
• If you wish to record your own “announcement only” greeting, follow the above
sequence after setting the AUDIBLE INDICATOR switch to ANN ONLY (page
40). Otherwise, the “normal” greeting will be recorded.
• You have to change the message each time you change the mode.
To check the greeting
Press (GREETING PLAY) to play back the greeting.
If you want to check the greeting with the handset, turn Jog Dial down to
make “PLAY GREETING” flash in step 2 on page 36, then press Jog Dial.
To change the greeting
Record a new greeting. The new greeting replaces the old one.
To erase the greeting
Press (ERASE) on the base unit while playing back the greeting with the
base unit, or press ERASE (9) on the handset while playing back it with
the handset.
The answering machine will answer a call with the prerecorded greeting.
To go back to the factory preset greeting
Press (ERASE) on the base unit while playing back the greeting with the
base unit, or press ERASE (9) on the handset while playing back it with
the handset. This will bring back the original greeting.
continued
Answering Machine Features
37US
Preparing the answering machine (continued)
Selecting the ring time
You can select the number of rings before the answering machine
starts to play back the greeting and records incoming messages. There
are three options of ring time. Select the ring time by setting the
RINGER SELECT switch.
RINGER SELECT
switch
38US
Set RINGER SELECT to
Mode
TS (Toll Saver)
If new messages have been recorded, the phone
answers at the second ring and records incoming
messages; if no new messages are recorded, it
answers at the fifth ring. When you call from an
outside phone and hear three rings, you know that
there are no new messages. If you hang up at this
point before the phone answers, you can save the
toll for the call.
5
The phone always answers at the fifth ring and
records incoming messages.
2
The phone always answers at the second ring and
records incoming messages.
Answering Machine Features
Selecting the recording quality
For the user who does not utilize the maximum recording capacity
(about 18 minutes), you can select a higher recording grade and enjoy
superior sound quality and clarity compared to the standard (NORM)
grade. As higher sound quality uses up more memory capacity, the
maximum recording time changes accordingly.
REC. QUALITY
switch
Answering Machine Features
Note
The approx. length of the three recording grades are:
HIGH (Short) – 8 minutes
MID – 11 minutes
NORM (Long) – 18 minutes
Actual recording time may vary.
continued
Answering Machine Features
39US
Preparing the answering machine (continued)
Selecting the answering mode
You can set the answering machine to record
incoming messages (normal mode), or just
make an announcement without recording
messages (announcement only mode).
You can record your own greeting, or use the
factory pre-recorded greetings.
In the normal mode, you also have the option
of having a beep to tell you if you have
AUDIBLE
received any new messages.
INDICATOR switch
Set AUDIBLE
INDICATOR to
When you wish to
ON
(normal mode)
play a greeting to ask the caller
to leave a message and have the
phone beep to alert you of
recorded incoming messages.
OFF
(normal mode)
play a greeting to ask the caller
to leave a message but you do
not wish to sound a beep.
ANN ONLY
(announcement only
mode)
make an announcement to the
caller without accepting
incoming messages when, for
example, you are away on a
long vacation.
Pre-recorded greeting
“Hello, I’m unable to answer
your call right now. Please leave
your name, number and
message after the tone.”
“Hello, I’m unable to answer
your call right now. Please call
again. Thank you.”
Note
The same greeting is used regardless of the answering mode. Therefore, if you decide to change
the mode, make sure that you record a new greeting to match the answering mode.
When the memory is full
The maximum recording area of this phone’s memory is about 18 minutes* (including
the greeting, messages, and memo). If the remaining recording area becomes less than
one minute, “F” flashes on the display, and the phone automatically switches to
announcement only mode, which does not record messages, and the greeting will be
switched to the pre-recorded greeting.
* Available time for recording at NORM (Long) sound quality.
If you wish to record more messages, erase the existing messages (see page 45). You
can also erase the messages from an outside phone (see page 50).
Note
The time for the memory to become full depends on the REC. QUALITY switch setting.
“F” flashes on the display at the time which corresponds to the recording sound quality for the
latter setting, if the switch setting is changed during the operation.
40US
Answering Machine Features
Turning on the answering function
Press (ANSWER ON/OFF)
so that it lights up in red.
To turn on the answering function from the handset
Press (REMOTE) and wait until the answering
machine function menu appears on the display.
1
PLAY MAILBOX 1
PLAY MAILBOX 2
If you hear five short error beeps and “OUT OF
RANGE” appears on the display, move closer to
the base unit.
Turn Jog Dial down to make “ANSWERING
ON” flash, and then press Jog Dial.
THE ANSWERING
FUNCTION IS ON
You hear a voice guidance and the ANSWER
ON/OFF button lights up in red.
3
Press (OFF).
Notes
• Do not allow more than 20 seconds to elapse during the operation procedure
when you turn on the answering function from the handset.
• When the memory is full, you hear five short error beeps and you cannot
turn on the answering function. Erase unnecessary messages (see page 45).
Tips
• The answering machine will automatically answer a call after 10 rings even if
the answering function is off. The answering function will remain on for all
subsequent calls.
• You can also turn on or off the answering function from an outside phone
(see page 50).
Answering Machine Features
2
continued
Answering Machine Features
41US
Preparing the answering machine (continued)
Mailbox usage
This phone offers you three voice mailboxes, providing a convenient
way to share the mailbox feature with other members of your
household or business.
When a caller calls
The caller can choose one of the two ways to leave a message:
• If calling from a touch-tone phone, the caller select a mailbox by
pressing (*)(1) (MAILBOX 1), (*)(2) (MAILBOX 2) or (*)(3)
(MAILBOX 3) while the caller hears the greeting. The greeting stops
and a beep will sound, then the caller can start recording a message.
• Wait until the greeting finishes, then start recording a message.
When the caller does not select a mailbox, the message is
automatically recorded to MAILBOX 1.
Notes
• If four minutes have passed while recording the incoming message, the line is
automatically disconnected.
• If the message is shorter than two seconds, it will not be recorded.
To turn off the answering function
Press (ANSWER ON/OFF) so that the red light turns off.
If you want to turn off the answering function from the handset, turn Jog
Dial down to make “ANSWERING OFF” flash in step 2 on page 41, then
press Jog Dial.
42US
Answering Machine Features
Playing back messages
Display
(ERASE)
(MAILBOX 1)
(MAILBOX 2)
(MAILBOX 3)
When you come home
If (ANSWER ON/OFF) flashes in
red, or the message counter
shows the number of new
messages and “NEW” in the
MAILBOX indicator on the
display flashes, press the
mailbox button ((MAILBOX 1),
(MAILBOX 2) or (MAILBOX 3)).
(ANSWER ON/OFF)
.(REPEAT/REVIEW)
(VOLUME)
The machine plays back from
the newest message received.
>(SKIP/QUICK)
To play back messages from the handset
Turn
1 Press
(REMOTE) and wait until the
answering machine function menu
Press
appears on the display.
VOL switch
PLAY MAILBOX 1*
PLAY MAILBOX 2
(OFF)
REVIEW (4)
> SKIP (3)
QUICK (6)
ERASE (9)
. REPEAT
(1)
“*” is displayed at the right of a
MAILBOX number which contains
new messages.
If you hear five short error beeps
and “OUT OF RANGE” appears
on the display, move closer to the
base unit.
Answering Machine Features
ALL MESSAGES
NEW 03 OLD 08
2 Turn Jog Dial down to make
“PLAY MAILBOX 1” to “PLAY
MAILBOX 3” flash, and then press
Jog Dial.
The machine plays back from the
newest message received.
3 Press (OFF).
continued
Answering Machine Features
43US
Playing back messages (continued)
Note
Do not allow more than 20 seconds to elapse during the operation procedure.
Additional tasks when playing back messages
To
Do this
Adjust the speaker volume
Press (VOLUME) (+) or (-).
Adjust the handset volume
Set the VOL switch on the handset to H (high),
M (middle) or L (low).
Stop playback
Press the mailbox button on the base unit again
or press Jog Dial on the handset.
Replay the messages
Press the mailbox button on the base unit again.
Skip to the next message
Press >(SKIP/QUICK) on the base unit or
> SKIP (3) on the handset while the current
message is playing.
Repeat the current message
Press .(REPEAT/REVIEW) on the base unit or
. REPEAT (1) on the handset while the
current message is playing.
Go back to previous messages Press .(REPEAT/REVIEW) on the base unit or
. REPEAT (1) on the handset within the
first three seconds of the current message.
44US
Review playback
Keep .(REPEAT/REVIEW) on the base unit or
REVIEW (4) on the handset pressed during
playback.
Play back quickly
Keep >(SKIP/QUICK) on the base unit or
QUICK (6) on the handset pressed during
playback.
Answering Machine Features
Erasing messages
To erase the message one by one
Press (ERASE) on the base unit while playing back the message
with the base unit, or press ERASE (9) on the handset while
playing back it with the handset.
To erase all messages in a mailbox from the base unit
Press (ERASE) on the base unit, and a mailbox button
((MAILBOX 1), (MAILBOX 2) or (MAILBOX 3)) .
You hear a long confirmation beep and all messages in the
selected mailbox are erased.
To erase all messages in a mailbox from the handset
1 Press (REMOTE) and wait until the answering machine
function menu appears on the display.
If you hear five short error beeps and “OUT OF RANGE”
appears on the display, move closer to the base unit.
Turn Jog Dial down to make “ERASE MAILBOX 1” to
“ERASE MAILBOX 3” flash, and then press Jog Dial.
3
Turn Jog Dial up to make “YES” flash, and then press Jog
Dial.
You hear a long confirmation beep and all messages in the
selected mailbox are erased.
Notes
• The display shows the total number of “new” messages. Therefore, it is reset
to “0” (on the base unit) or “00” (on the handset) when you play back all new
messages, even they are not erased yet. Be sure to erase unnecessary
messages before the memory becomes full.
• When the number of new messages exceeds 99, “99” flashes on the display of
the base unit and “99” appears on the display of the handset.
• If a call comes in during playback, the playback stops.
• If a power interruption occurs or the AC power adaptor is disconnected
while erasing a message, all recorded message may be erased.
• Do not allow more than 20 seconds to elapse during the operation procedure
when you erase messages from the handset.
Answering Machine Features
2
Tip
You can also listen to the messages or erase the messages from a outside phone
(page 50).
Answering Machine Features
45US
Screening incoming calls
You can screen calls by leaving the answering function on (see page
41) while you are at home. When a call is answered, you can hear the
message being recorded through the base unit or handset but the caller
cannot hear you. Then, you can decide whether to answer the call or
not. This function is available both the base unit and the handset.
However, the following procedures are required in order to screen
incoming calls on the handset.
To screen incoming calls
on the handset
Press (REMOTE) while
“** ANSWERING **” is
displayed.
“CALL SCREENING” appears on
the display of the handset.
(TALK)
To answer the call
Press (TALK) on the handset.
Recording is stopped and you can
speak to the caller.
Note
If the answering volume is set to minimum, you cannot screen the calls on the
base unit.
Tips
• You can conclude call screening by pressing (OFF) on the handset.
• You can also answer the call by picking up the handset on another phone if it
is connected to the same line.
46US
Answering Machine Features
Recording a memo
You can record a “memo” (up to four minutes) as a personal reminder
or as a message for other people. You can play back the recorded
memo like any incoming messages (see page 43).
You can record a memo on both the base unit and the handset.
1 Press (MEMO).
You hear a voice guidance.
2 Select a mailbox by pressing
MIC (Microphone)
(MAILBOX 1)
(MAILBOX 2)
(MAILBOX 3)
(MAILBOX 1), (MAILBOX 2) or
(MAILBOX 3). You will hear a
voice guidance, then a long
confirmation beep.
3 After the tone, start recording.
4 Press (MEMO) to stop recording.
The message number in the
display increases by one.
Notes
• If you press (MEMO) when the memory is full (“F” flashing on the display),
you hear five short error beeps and you cannot record a memo.
• If a call comes in while recording a memo, recording is canceled. Start over
the procedure.
• If the remaining memory becomes full while recording, recording stops
automatically and “F” flashes on the display.
• You cannot operate the base unit while the handset is in use.
• This answering machine begins to record a memo when it detects voice.
Note that recording does not begin if the voice is extremely low or there
is no sound.
Answering Machine Features
Speak about 12 inches (30 cm)
away from the microphone.
Tip
If four minutes have passed in step 3, recording stops automatically, and the
recorded memo is counted as a new message.
continued
Answering Machine Features
47US
Recording a memo (continued)
To record a memo from the handset
Turn
1 Press (REMOTE) and wait until
Press
the answering machine function
menu appears on the display.
If you hear five short error
beeps and “OUT OF RANGE”
appears on the display, move
closer to the base unit.
(OFF)
PLAY MAILBOX 1
PLAY MAILBOX 2
2 Turn Jog Dial down to make
“REC MEMO BOX 1” to “REC
MEMO BOX 3” flash, and then
press Jog Dial.
REC MEMO BOX 1
START CANCEL
3 Press Jog Dial.
You hear a long confirmation beep.
4 After the tone, start recording.
Speak into the handset.
NOW RECORDING
COMPLETE CANCEL
5 Press Jog Dial to stop recording.
You hear a long confirmation beep.
6 Press (OFF).
Notes
• Do not allow more than 20 seconds to elapse between steps 1 and 2 of the procedure.
• When the memory is full (“F” flashing on the display of the base unit), you hear five short
error beeps in step 2 and you cannot record a memo.
• If a call comes in while recording a memo, recording is canceled. Start over the procedure.
• If the remaining memory becomes full while recording, recording stops automatically and “F”
flashes on the display of the base unit.
Tip
If four minutes have passed in step 4, recording stops automatically, and the recorded memo is
counted as a new message.
48US
Answering Machine Features
Operating from an outside phone
You can call from a touch-tone phone and pick up new messages
recorded on the phone. First, you just set the remote ID code (security
code) and turn on the answering function before going out. Setting the
remote ID code (security code) is only possible on the handset.
Setting the remote ID code (security code)
Turn
1 Press (REMOTE) and wait until
Press
the answering machine function
menu appears on the display.
PLAY MAILBOX 1
PLAY MAILBOX 2
(OFF)
If you hear five short error
beeps and “OUT OF RANGE”
appears on the display, move
closer to the base unit.
2 Turn Jog Dial down to make
SET SECURITY No
3 Enter
the four digits of the
remote ID code (security code)
using the dialing keys.
4 Press Jog Dial.
The remote ID code (security
code) is set, and you hear a long
confirmation beep.
Answering Machine Features
“SET SECURITY No” flash,
and then press Jog Dial.
5 Press (OFF).
Note
Do not allow more than 20 seconds to elapse during the operation procedure.
To change the remote ID code (security code)
continued
Enter a new remote ID code (security code). The new code will replace
the old one.
Answering Machine Features
49US
Operating from an outside phone (continued)
Picking up new messages
1
2
Call your phone from a touch-tone phone.
While you hear your greeting play, press (#). The greeting stops.
After confirming the greeting stops, enter your remote ID code (security
code). You hear a long confirmation beep.
Following the voice guidance informing you of the number of messages
recorded, the phone stands by for you to enter a control code.
3
To do other operations, enter the control code within 20 seconds (see the
table below). To quit, hang up the phone.
Control codes for remote operations
To
Press
Play back messages in MAILBOX 1 (#) (1)
Play back messages in MAILBOX 2 (#) (2)
Play back messages in MAILBOX 3 (#) (3)
Repeat the current message
(#) (4) while the message is being played back
Skip the current message
(#) (6) while the message is being played back
Erase the current message
(#) (9) while the message is being played back
Erase all messages in MAILBOX 1 (#) (9) (#) (1)
Erase all messages in MAILBOX 2 (#) (9) (#) (2)
Erase all messages in MAILBOX 3 (#) (9) (#) (3)
Record a new greeting
(up to one minute)
(*) (7). When you hear a long beep, start recording your
greeting. Press (*) (*) to stop recording.
Turn on the answering function
(*) (0)
Turn off the answering function
(#) (0)
Stop the current operation
(*) (*)
If you forgot to turn the answering function on
Call your phone and let it ring 10 times until it answers. Then the answering function
automatically turns on.
Notes
• If you enter a wrong remote security code three times, the line will be disconnected.
• If the greeting does not stop, press and hold (#) again.
To use the toll-saver feature
Set RINGER SELECT to TS. See page 38 for details.
50US
Answering Machine Features
Caller ID Features
Understanding the Caller ID service
Caller ID allows the caller’s phone number to be shown on the display
before you answer the call. In order to use this feature, you must first
subscribe to Caller ID service. The name of this service may vary
depending on your telephone company.
To use this feature, be sure to enter the area code (see page 14).
When you receive a call
The phone number appears on the display with the date and time as
shown in the following example.
If your Caller ID service includes the caller name service, the caller’s
name also appears on the display (up to 15 letters).
Caller’s name
Caller’s phone number
The date and time received
SMITH JOHN
1-201-123-4567
When you answer the call, the Caller ID display changes to the
“TALK” display.
Caller ID Features
Notes
• The caller’s phone number and/or name will not appear in the following
cases:
- “OUT OF AREA”: when the call is made through a telephone company
which does not offer Caller ID service (including international calls).
- “PRIVATE”: when the call is “blocked”. For privacy reasons, many states
allow callers the option to prevent his or her telephone data from being
displayed on the other party’s Caller ID display.
• If the call is from an office which uses multiple lines, the displayed phone
number may not match the number you use to call the extension.
About the memory match function
If you receive a call from a phone number which is stored on one of the
ONE-TOUCH DIAL buttons (see page 26) or in the Phone Directory
(see page 28), the ringer sound will change to a higher tone from the
second ring.
Note
The memory match function does not work with “OUT OF AREA” or “PRIVATE”
calls; and it may not work with calls made from an office which uses multiple lines
because the number does not always match the one you stored in this phone.
Caller ID Features
51US
Looking at the Caller ID list
The phone stores the data of the last 20 calls received including “OUT
OF AREA” and “PRIVATE” calls. It keeps track of all calls received;
even if they were not answered.
Viewing the Caller ID list
You can look through the Caller ID list to check the phone number
and/or name of the calls received.
Turn
1 Turn Jog Dial.
The display shows the number
of “NEW” (calls which you have
not viewed) and “OLD” (calls
which you have viewed) calls.
NEW 08 OLD 12
2 Turn Jog Dial down to display
older data or up to display
newer data.
Notes
• If a 21st call is received, the oldest data is automatically erased.
• When you have checked all data , “END OF LIST” appears.
Tip
If there is a “NEW” data, the NEW CALL lamp of
the base unit flashes.
52US
Caller ID Features
NEW CALL lamp
About the “*” mark
SMITH JOHN
*
1-201-123-4567
“*” appears if there are more than two calls
from the same phone number. The older data
will be replaced by the new data, so the calls
are counted as only one call.
Erasing data from the Caller ID list
Old data will be erased automatically when a 21st call comes in, but
you can also manually erase unnecessary data one by one or erase the
entire list.
To erase the phone number one by one
Display the phone number you want to erase
from the Caller ID list (see page 52).
SMITH JOHN
1-201-123-4567
2
Press Jog Dial.
DIAL PGM ERASE
1-201-123-4567
3
Turn Jog Dial up to make “ERASE” flash and
press Jog Dial.
ERASE NO YES
1-201-123-4567
4
Turn Jog Dial up to make “YES” flash, then
press Jog Dial.
Caller ID Features
1
You hear a long confirmation beep and the data
is erased.
continued
Caller ID Features
53US
Looking at the Caller ID list (continued)
To erase the entire list at once
1
Display any Caller ID data.
SMITH JOHN
1-201-123-4567
2
Press Jog Dial.
DIAL PGM ERASE
1-201-123-4567
3
Turn Jog Dial up to make “ERASE” flash and
press Jog Dial.
ERASE NO YES ALL
1-201-123-4567
4
Turn Jog Dial up to make “ALL” flash, then
press Jog Dial.
ALL ERASE NO YES
1-201-123-4567
5
Turn Jog Dial up to make “YES” flash, then
press Jog Dial.
NEW 00 OLD 00
You hear a long confirmation beep and the
entire list is erased.
Note
“ALL” appears only when all the data had become “OLD” data. If there is any
“NEW” data, you cannot erase the entire list.
54US
Caller ID Features
Using the Caller ID list
By using the Caller ID list, you can call back a phone number from the
Caller ID list easily, or store numbers from the Caller ID list into the
Phone Directory.
Calling back a number from the Caller ID list
Turn
Press
1 Display the phone number you
want to call from the Caller ID
list (see page 52).
SMITH JOHN
1-201-123-4567
2 Press Jog Dial.
DIAL PGM ERASE
1-201-123-4567
3 Press Jog Dial again.
Notes
• If the number displayed in step 1 is not the one you should call back, you can
change the number of digits of the phone number as described on page 57.
• If the phone is connected to a Private Branch Exchange (PBX), you may not
be able to call back from the Caller ID list because an outside line access digit
is necessary.
Caller ID Features
The phone automatically dials
the displayed number.
Tip
You may press (TALK) to make a call instead of doing steps 2 and 3.
continued
Caller ID Features
55US
Using the Caller ID list (continued)
Storing a number of the Caller ID list into
the Phone Directory
1
Display the name and phone number you want
to store from the Caller ID list (see page 52).
SMITH JOHN
1-201-123-4567
2
Confirm the number and press Jog Dial.
DIAL PGM ERASE
1-201-123-4567
3
Turn Jog Dial up to make “PGM” flash and
press Jog Dial.
SMITH JOHN
12011234567
The cursor flashes at the end of the name.
Enter or change the name, if necessary (see page
29).
4
Press Jog Dial.
The cursor flashes at the end of the phone
number.
SMITH JOHN
12011234567
Enter or change the phone number, if necessary
(see page 29).
5
Press Jog Dial again.
You hear a long confirmation beep and the
name and number are stored.
Notes
• Do not allow more than 20 seconds to elapse during the operation procedure.
• If the number displayed in step 1 is not the one you should store, you can
change the number of digits of the phone number as described on page 57.
• If the phone is connected to a Private Branch Exchange (PBX), you may need
to add an outside line access digit.
56US
Caller ID Features
To change the number of digits of the phone
number
If the number of digits of the phone number in the Caller ID list is
different from the actual phone number, you need to adjust the
number of digits of the phone number to call back or store into the
Phone Directory.
1
While the phone number from the Caller ID list is displayed,
press (#) repeatedly until the phone number with the
correct number of digits appears on the display.
Each time you press (#), the number of digits changes as
follows:
When the home area code and the local area code do
not match
SMITH JOHN
1-201-123-4567
SMITH JOHN
201-123-4567
SMITH JOHN
123-4567
SMITH JOHN
1-123-4567
Caller ID Features
When the home area code matches
SMITH JOHN
123-4567
SMITH JOHN
1-201-123-4567
SMITH JOHN
1-123-4567
SMITH JOHN
201-123-4567
continued
Caller ID Features
57US
Using the Caller ID list (continued)
When the local area code matches
2
SMITH JOHN
201-123-4567
SMITH JOHN
1-123-4567
SMITH JOHN
1-201-123-4567
SMITH JOHN
123-4567
Continue the operation to call or store the phone number
with the correct number of digits (pages 55 and 56).
Notes
• You need to adjust the number of digits each time you call back from the
Caller ID list as the changes to the Caller ID data is not stored in memory.
• You may not be able to change the number of digits depending on the Caller
ID data.
58US
Caller ID Features
Using “Caller ID with call waiting”
service
This telephone is compatible with the “Caller ID with call waiting”
service. Make sure that your telephone company offers this service.
Like the basic Caller ID service, you need to subscribe to “Caller ID
with call waiting” in order to use this service.
Even though you may have already subscribed to “Caller ID” and
“call waiting” as two separate services, you need to request a
subscription to “Caller ID with call waiting” as a single service.
This is a new service that combines the two services.
Even though you now have a “Caller ID with call waiting”
compatible phone, unless you subscribe to the combined “Caller ID
with call waiting” service, you will not be able to see the name
and number of the second caller.
When a new call comes in while you are talking, the caller’s name
and/or phone number of the new call appears on the display for about
20 seconds.
To switch to another caller
1 To switch to the new caller,
press (CALL WAITING/FLASH).
press (CALL WAITING/FLASH)
again.
Caller ID Features
Caller ID Features
2 To switch back to the first caller,
59US
Additional Information
Mounting the base unit on a wall
1
1 Raise the hang up tab.
2 Plug the telephone line cord to
Hang-up tab
the LINE jack and the AC power
adaptor to the DC IN 9V jack,
and hook the cords. Use the
shorter cord for mounting.
3 Attach the wall bracket to the
center of the base unit.
2
Align the f marks of the wall
bracket with those of the base
unit.
4 Plug the telephone line cord to
AC power
adaptor cord
Telephone
line cord
the telephone outlet, and hook
the base unit to the wall plate.
5 Plug the AC power adaptor to
an AC outlet. Then raise the
antenna so that it points
towards the ceiling.
3
4,5
1
2
Wall
bracket
Telephone
line cord
Wall
plate
AC outlet
Tip
To remove the wall bracket, press the lower tabs.
60US
Additional Information
AC power
adaptor
Notes on power sources
On battery pack
For the customers in the USA
• Store the battery pack at a
temperature between 41°F (5°C) and
95°F (35°C) for best performance.
RECYCLING NICKEL-CADMIUM
BATTERIES
• If you do not use the handset for a
long period of time, remove the
battery pack from the handset after
charging for more than 12 hours, and
base unit after charging for more than
24 hours when you have a spare
battery. This maintains battery life.
On power failure
During a power interruption, you
cannot make or receive calls, and you
cannot use the answering machine.
Nickel-Cadmium batteries
are recyclable. You can help
preserve our environment
by returning your
unwanted batteries to your
nearest point for collection,
recycling or proper
disposal.
Note: In some areas the disposal of nickelcadmium batteries in household or
business trash may be prohibited.
RBRC (Rechargeable Battery Recycling
Corporation) advises you about spent battery
collection by the following phone number.
Call toll free number: 1-800-822-8837
(United States and Canada only)
Caution: Do not handle damaged or leaking
nickel-cadmium batteries.
Additional Information
Additional Information
61US
Maintenance
• Clean the cabinets with a soft cloth
slightly moistened with water or a
mild detergent solution. Do not use
any type of abrasive pad, scouring
powder or solvent such as alcohol or
benzine as they may damage the
finish of the cabinet.
• If the charge terminals of the base unit
and handset are soiled, wipe them
with a soft cloth.
If you have any questions or problems
concerning your phone, please consult
your nearest Sony dealer.
62US
Additional Information
Troubleshooting
Symptom
Remedy
You hear five short error
beeps when you press (TALK).
• Make sure you set up the base unit correctly (page 8).
• Move the handset closer to the base unit.
You hear no dial tone.
• Make sure the telephone line cord is securely
connected to the telephone outlet.
• Make sure the battery is fully charged (page 11).
The phone does not connect at
all, even though the number
you dial is correct.
• Make sure the dialing mode is set correctly (page 10).
The phone does not redial
correctly.
• Make sure the last dialed number is really the one you
want to dial.
You hear five short error beeps
when you try to redial.
• The number you last dialed exceeds 32 digits
(including the tone and pause digits if used).
• The number you last dialed is erased.
The handset does not ring.
• Set the RING switch on the handset to ON.
• The battery may be weak. Charge the battery for
more than 12 hours (page 11).
• Make sure you set up the base unit correctly (page 8).
• Move the handset closer to the base unit.
You hear interference during
conversation.
• Move the handset closer to the base unit.
• Place the base unit away from noise sources (page 8).
You hear a beep every second
during conversation and “OUT
OF RANGE” appear on the
display.
• It is an out-of-range alarm. Move the handset closer to
the base unit within one minute.
You hear a beep twice per
second and E and “BATTERY
LOW” appear on the display.
• The battery is weak. Charge the battery for more than
12 hours (page 11).
An incorrect language is set for
the display and the voice
guidance.
• Follow the procedure for changing the language
(page 17).
Additional Information
Dsplay and the
voice guidance
language
During conversation
Receiving
calls
Making calls
If you’ve experienced any of the following difficulties while using your
phone, use this troubleshooting to help you remedy the problem.
Should any problem persist, consult your nearest Sony dealer.
continued
Additional Information
63US
Troubleshhoothig (continued)
Operating from an
outside phone
Answering machine
One-touch dialing/
Phone Directory
Symptom
64US
Remedy
You hear five short error beeps • Make sure you follow the procedure in storing the
and cannot store a number on a
number correctly (pages 26 and 28).
one-touch dial or in the Phone
Directory.
You hear five short error beeps
when you try to make a onetouch dial call.
• You entered a one-touch dialing button to which no
phone number has been stored.
One-touch dialing or Phone
Directory dialing is incorrect.
• Store a correct number (pages 26 and 28).
You cannot hear anything from
the speaker.
• Use the VOLUME control on the base unit to increase
the speaker volume.
No time stamp is heard.
• Make sure the day and time are set (page 33).
• The day and time may have been cleared due to a
power interruption. Set them again (page 33).
You cannot record the greeting
properly.
• Keep your message between two seconds and four
minutes.
• Make sure you speak about 12 inches (30 cm) away
from the microphone when recording.
The phone does not record
messages
• Check the answering mode. The phone cannot record
messages in announcement only mode (page 40).
• Make sure that the memory is not full. When the
remaining recording area is less than one minute, the
phone switches to announcement only mode
automatically.
• The phone does not record a message that is shorter
than two seconds.
• Even if the message is longer than four minutes, the
phone only records up to four minutes.
The recordable time is short.
• Make sure the position of the REC. QUALITY switch
(page 39).
The phone does not accept your • Make sure you call from a touch-tone phone.
remote ID code (security code). • Make sure you entered your remote ID code (security
code) within two seconds after you have entered (#).
You hear error beeps when you • Make sure the remote ID code (security code) is
correct.
enter your remote ID code
(security code).
A long confirmation beep does • Enter your remote ID code (security code) while the
greeting is being played back.
not sound when you enter your
remote ID code (security code). • Make sure you are calling from a touch-tone phone.
Additional Information
Operating
from the
handset
Caller ID
Symptom
Remedy
You cannot operate with the
handset.
• Move the handset closer to the base unit.
• Make sure the battery is fully charged (page 11).
The caller’s name and/or
phone number does not appear
on the display.
• Make sure you have subscribed to Caller ID service.
• Caller ID service may not work when the phone is
connected to a Private Branch Exchange (PBX).
• The call is made through company which does not
offer Caller ID service. ”OUT OF AREA” will appear
on the display.
• The call was “blocked”. “PRIVATE” will appear on
the display.
• You answered the call while “** RINGING **” is
displayed. Be sure to answer after the Caller ID data is
displayed.
• Make sure you have subscribed to “Caller ID with
The caller’s name and/or
call waiting” service (page 59).
phone number does not appear
• Make sure nobody is talking on another phone on the
on the display during call
same telephone line.
waiting.
You cannot dial the number
from the Caller ID list.
• Make sure you entered your home area code correctly
(page 14).
• You may need to change the number of digits of the
phone number (page 57).
• This function may not work when the phone is
connected to a Private Branch Exchange (PBX).
The memory match function
does not work.
• If the call is from an office which uses multiple lines,
the phone number may not match the number you
put in the memory.
• If you stored the phone number with an outside line
access digit in the Phone Directory because the phone
is connected to a Private Branch Exchange (PBX), the
phone number will not match the Caller ID data.
Additional Information
Additional Information
65US
Power source/battery
Troubleshhoothig (continued)
Symptom
Remedy
The CHARGE lamp does not
light up when you place the
handset to charge.
• Wipe the charge terminals of the base unit and the
handset with a soft cloth for better contact of the
charge terminals.
• Make sure the handset is placed on the base unit
properly.
The battery duration is short.
• The battery pack was charged less than 12 hours (due
to power failure, etc.).
• The usable life of the battery has expired and needs
replacement.
The handset does not work.
• The battery may be weak. Charge the battery for more
than 12 hours (page 11).
Note
If any of the remedy did not work, there may be something wrong with the
handset.
Replace the handset on the base unit, then pick it up and try again. If the
handset is on the base unit, pick up the handset and replace it again.
66US
Additional Information
Message counter
The message counter on the base unit shows the following
information.
When the counter shows
It means
Number (0-99)
Number of messages not yet played back. The counter shows
up to 99 messages. After that, ”99“ flashes to tell you that
there are 100 or more messages.
P
Flashes when the day and time is cleared due to a power
interruption, or when you connect the base unit to the AC
outlet for the first time (pages 9 and 34).
A
The announcement only mode is selected (page 40).
F
The recording area is full. Erase unnecessary messages
(page 45).
Additional Information
Additional Information
67US
Specifications
General
Base unit
Spread method
Direct-Sequence Spread-Spectrum
Access method
FDMA-TDD
Operation frequency
902 - 928 MHz
Operating channel
14 channels
Dial signal
Tone, 10 PPS (pulse) selectable
Supplied accessories
See page 7.
Power source
DC 9V from AC power adaptor AC-T46
Battery charging time
Approx. 24 hours
Dimensions
Approx. 6 3⁄ 8 x 2 7⁄8 x 8 3⁄4 inches (w/h/d),
antenna excluded
(approx. 160 x 71 x 222 mm)
Antenna: Approx. 4 1⁄ 2 inches
(approx. 113 mm)
Mass
Approx. 1 lb 3 oz (approx. 540 g), wall
bracket excluded
Handset
Power source
Rechargeable battery pack BP-T31
Battery charging time
Approx. 12 hours
Battery life
Standby: Approx. 7 days
Talk:
Approx. 6 hours
Dimensions
Approx. 2 1⁄4 x 7 1⁄4 x 2 1⁄4 inches (w/h/d),
antenna excluded
(approx. 56 x 183 x 55 mm)
Antenna: Approx. 3 inches
(approx. 75 mm)
Mass
Approx. 9.5 oz (approx. 270 g), battery
included
68US
Additional Information
Answering machine
Maximum recording time
About 18 minutes (at NORM (Long)
recording quality), using incorporated IC
Greeting message
Up to 4 minutes
Incoming message
Up to 4 minutes/message
Memo
Up to 4 minutes/message
Design and specifications are subject to
change without notice.
Index
A
E, F
Adjusting volume
handset 22
speaker 44
Announcement only 40
Answering machine
turning on 41
Area code 14
Audible indicate 40
Erasing
Caller ID data 53
last phone number
dialed 24
messages 45
Phone Directory 30
G
Greeting 35
B
Battery pack
charging 11
duration 12
C
Call waiting service 22, 25
Caller ID 51
Caller ID list 52
calling back 55
memory match function
51
storing in Phone
Directory 56
Caller ID with call waiting
59
Connection 9
Control codes for remote
operations 50
Day and time stamp 33
Dialing mode
choosing 10
switching to the tone
temporarily 22
Directroy
Phone Directory 28
Home area code 14
I, J, K
Identifying the parts 18
L
Language of the display
and the voice guidance 17
Local area code 15
Location, base unit 8
M, N
Mailbox 42, 43
Making calls 22
Memo 47
Memory match funtion 51
Messages 43
Mounting the base unit on
a wall 60
O
One-touch dialing 26
Operating from an outside
phone 49
OUT OF AREA 51
P, Q
Package contents 7
Paging 32
Phone Directory 28
R
Recording
greeting 35
memo 47
Recording quality 39
Receiving calls 25
Redialing 24
Remote ID code
(security code) 49
Ringer
RING switch 25
S
Screening calls 46
Setting up
base unit 8
handset 11
Speaker 44
Stamping messages with
day and time 33
Storing Caller ID data in
Phone Directory 56
T, U
Toll-saver feature 38
Tone dialing
dialing mode 10
switching to 22
Troubleshooting 63
V, W, X, Y, Z
Volume
handset 22
speaker 44
Additional Information
Additional Information
D
H
Playing
annoucement only 40
messages 43
PRIVATE 51
Pulse dialing 10
69US
For the customers in the USA
Be sure to save the receipt and attach it to your WARRANTY card when having
your equipment repaired at an authorized Sony service station.
www.sony.com/productregistration
Sony Corporation Printed in Taiwan, R.O.C.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement