Sony Cordless Telephone SPP-N1000 User manual

Sony Cordless Telephone SPP-N1000 User manual
3-048-609-51 (2)
For the customers in the USA
IMPORTANT SAFETY
INSTRUCTIONS
Cordless Telephone
Operating Instructions
Manual de instrucciones (verso)
Owner’s Record
The model and the serial numbers are located at the bottom
of the unit. Record the serial number in the space provided
below. Refer to these numbers whenever you call upon your
Sony dealer regarding this product.
Model No. SPP-N1000/N1004 Serial No.
SPP-N1000/N1004
Sony Corporation © 2001 Printed in China
For the customers in the USA
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub, in a wet basement, or near a
swimming pool.
2. Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not
dispose of batteries in a fire. They may explode. Check with local codes
for possible special disposal instructions.
SAVE THESE
INSTRUCTIONS
INFORMATION FOR
FCC REGURATION CLAIM
1. This equipment complies with Part 15 and Part 68 of the FCC rules for
the United States. On the bottom of this equipment is a label that
contains, among other information, the FCC certification number and
ringer equivalence number (REN) for this equipment. If requested, this
information must be provided to the telephone company.
2. This equipment connect to nationwide telephone network through a
modular telephone jack which applicable certification jack (connector)
is USOC-RJ11C.
3. The FCC compliant telephone cord and modular plug is provided with
this equipment. This equipment is designed to be connected to the
telephone network or premises wiring using a compatible modular jack
that is part 68 compliant.
4. The REN is used to determine the quantity of devices that may be
connected to the telephone line. Excessive RENs on the telephone line
may result in the devices not ringing in response to an incoming call.
Typically, the sum of the REN’s should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as
determined by the total RENs, contact the local telephone company.
5. If this equipment (SPP-N1000/N1004) causes harm to the telephone
network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance
notice isn’t practical, the telephone company will notify the customer as
soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
6. The telephone company may make changes to it’s facilities, equipment,
operations or procedures that could affect the operation of the
equipment. If this happens the telephone company will provide advance
notice so you can make the necessary modifications to maintain
uninterrupted service.
7. If trouble is experienced with this equipment (SPP-N1000/N1004), for
repair or warranty information, please contact Sony Direct Response
Center: Tel 1-800-222-7669. If the equipment is causing harm to the
telephone network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
8. All repairs will be performed by an authorized Sony service station.
9. This equipment may not be used on coin service provided by the Phone
Company or Party Lines.
10. This equipment is hearing aid compatible.
When programming emergency numbers and (or) making test calls to
emergency numbers:
1. Remain on the line and briefly explain to the dispatcher the reason for
the call.
2. Perform such activities in the off-peak hours, such as early morning or
late evenings.
Operation is subject to the following two conditions: (1)This device may not
cause interference, and (2)This device must accept any interference,
including interference that may cause undesired operation.
Caution
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
Privacy of communications may not be ensured when using this phone.
Be sure to save the receipt and attach it to your WARRANTY card when having your
equipment repaired at an authorized Sony service center.
Note
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Notes
• Use only the supplied AC-T127 AC power adaptor. Do not use
any other AC power adaptor.
• Connect the AC power adaptor to a continuous power supply.
• Place the base unit close to the AC outlet so that you can unplug
the AC power adaptor easily.
–
+
Tip
If your telephone outlet is not modular, contact your telephone
service company for assistance.
Modular
Prepare the battery pack
Insert the battery into the handset and charge first before you start using your phone.
1
2
3
BP-T50
4
Red
Black
Setting up the phone
LINE/CHARGE lamp
Caution
The cordless telephone operates at a frequency that may cause interference to nearby
TVs and VCRs; the base unit should not be placed near or on the top of a TV or VCR;
and, if interference is experienced, moving the cordless telephone farther away from
the TV or VCR will often reduce or eliminate the interference.
Choose the best location
1
2
Slide open the battery compartment lid of the handset.
3
4
Insert the battery pack, and close the lid.
Away from noise sources such as a window
by a street with heavy traffic
Away from television
sets and other
electronic equipment
Polarity of the plug
Away from heat sources, such as
radiators, airducts, and sunlight
Away from a microwave oven
Away from excessive
moisture, extremely low
temperatures, dust,
mechanical
vibration, or shock
Connect the battery connector with correct polarity (black wire goes on
lower side and red wire goes on upper side), and hook the cords.
Place the handset on the base unit.
The LINE/CHARGE lamp lights up when the handset is properly seated
on the charge terminals of the base unit. Charge the battery pack for
more than 12 hours so that the battery is fully charged. The LINE/
CHARGE lamp remains lit even after charging is completed.
Battery duration
A fully charged battery pack lasts for about:
• 10 hours when you use the handset continuously.
• 30 days when the handset is in standing by.
Notes
• The battery pack will gradually discharge over a long period of time, even if not in use.
• If you leave the battery pack in the handset without charging it, the battery pack will be
completely discharged. It may require several times of charging to recover to its full capacity.
• If the battery runs out completely, the setting of dialing mode, the speed dial numbers and the
digital security code will be erased. If this happens, charge it on the base unit for over 12 hours.
Then choose the dialing mode, set the ringer type, reprogram the speed dial numbers, and
assign a new digital security code (see “Resetting the digital security code”). You may need to
charge the battery several times before it is recharged to its full capacity.
To obtain the best performance from battery
Away from a personal
computer
Near a central location
and on a level surface
Away from a another
cordless telephone
Connect the base unit
If you want to hang the base unit on the wall, mount the unit first (see “Mounting the
base unit on the wall”).
3
When to purchase a new battery pack
If the battery lasts only a few minutes even after 12 hours of charging, the usable
life of the battery has expired and needs replacement. Contact your local Sony
authorized dealer or service center, and ask for Sony BP-T50 rechargeable battery
pack.
Note
Battery life may vary depending on usage condition and ambient temperature.
Choose the dialing mode
2
To AC outlet
Do not place the handset on the base unit after each call. The battery works best if the
handset is returned to the base unit after two or three calls. However, do not leave the
handset off the base unit for a long period of time as this will completely discharge
the battery pack.
For the telephone to work properly, select an appropriate dialing mode (tone or
pulse). The default setting is tone.
AC power adaptor
(supplied AC-T127)
To DC IN 9V
Hook the cord.
To telephone
outlet
To LINE
1 Telephone line cord
TALK/BATT
LOW lamp
(supplied)
1
Connect the telephone line cord to the LINE jack and to a telephone
outlet.
2
Connect the AC power adaptor to the DC IN 9V jack and to an AC
outlet.
3
Raise the antenna. Make sure it points toward the ceiling.
1, 4
2
1
Press (PGM).
The TALK/BATT LOW lamp
flashes.
2
Press (* TONE).
You hear a confirmation beep.
3
Press (1) for pulse dialing or
(2) for tone dialing.
4
Press (PGM).
You hear a long confirmation
beep and the TALK/BATT LOW
lamp goes off.
Note
Do not allow more than 20 seconds to elapse between each step of the procedure.
Making and receiving calls
Making calls
Speed dialing
You can dial with a touch of a few keys by storing a phone number on a dialing key.
1
2
(FLASH)
TALK/BATT
LOW lamp
VOL
switch
2
4
3
4
(* TONE)
(REDIAL/PAUSE)
Pick up the handset from the
base unit.
Press (TALK), and wait until
the TALK/BATT LOW lamp
lights up.
You then hear a dial tone. If
you hear beeps, move closer to
the base unit.
Storing phone numbers
1
Press (PGM).
The TALK/BATT LOW lamp
flashes.
2
3
Press (SPEED DIAL).
4
Enter the phone number you want
to store.
You can enter up to 20 digits,
including a tone and a pause, each
of which is counted as one digit.
5
Press (PGM).
You hear a long confirmation
beep, and number is stored. The
TALK/BATT LOW lamp goes off.
TALK/BATT
LOW lamp
Dial the phone number.
When you’re done talking,
press (OFF).
The TALK/BATT LOW lamp
goes off.
1, 5
2
Microphone
(CHANNEL/RINGER)
Receiving calls
1
2
When you hear the phone ring;
• Press (TALK) (or any key except (OFF)).
or
• Pick up the handset from the base unit when the handset is placed on
the base unit.
The TALK/BATT LOW lamp lights up.
(REDIAL/PAUSE)
Press one of the dialing keys ((0)
to (9)) to store a phone number
on.
You hear a confirmation beep.
Note
Do not allow more than 20 seconds to elapse between each step of the procedure.
Tip
If you enter a wrong number, press (PGM), then start from the beginning.
To store a number to be dialed via Private Branch Exchange (PBX)
Before entering a phone number in step 4, do as follows:
When you’re done talking, replace the handset on the base unit or press
(OFF).
The TALK/BATT LOW lamp goes off.
Additional tasks
To
Do this
Adjust the handset
volume
Set the VOL switch to H (high), M (middle) or L (low).
Switch to tone
Press (* TONE) after you’re connected.
dialing temporarily The line will remain in tone dialing until disconnected.
Set the ringer type
While the handset is not in use, press (CHANNEL/RINGER). Each
press of (CHANNEL/RINGER) switches the ringer type by one of
four type.
Switch to another
call (“call waiting
service”*)
Press (FLASH).
Press the button again to get back to the first caller.
* You need to subscribe to the service from your telephone company.
Notes
• Do not cover the microphone during the conversation; otherwise, the other party cannot hear
your voice.
• If you hear beeps during the conversation, move closer to the base unit; otherwise, the call will
be disconnected after 15 seconds. Note that, however, you may not hear beeps if it’s noisy on
the handset.
1 Enter the outside line access digit (e.g., 9).
2 Press (REDIAL/PAUSE).
To change a stored number
Store a new number, as described previously.
Note
You can replace the stored number with a new number, but you cannot just erase it.
Making calls with speed dialing
1 Press (TALK) and wait until the TALK/BATT LOW lamp lights up.
2 Press (SPEED DIAL).
3 Enter the desired speed dialing number ((0) to (9)).
The phone number stored in the speed dialing number will be dialed.
Locating the handset
You can page the handset from the base unit. Note that you cannot page if the handset
is in use.
Press (HANDSET LOCATOR).
The handset rings for about one
minute.
To end the page, press (OFF) on
the handset.
If interference occurs on the handset
When you press (TALK), the handset automatically searches for the channel with the
best reception. However, if you notice interference during a conversation, move
closer to the base unit.
If interference persists, press (CHANNEL/RINGER) to switch to another channel to
improve the sound quality of your telephone conversation.
Note
If you hear five short beeps when you press (CHANNEL/RINGER), move closer to the base unit.
If the handset battery becomes weak during a call
The handset will beep every three seconds with the TALK/BATT LOW lamp
flashing at the same time. Finish your call and charge the battery pack.
Caution
If this occurs, you cannot use the handset without charging it for more than one minutes.
Redialing
1 Press (TALK), and wait until the TALK/BATT LOW lamp lights up.
2 Press (REDIAL/PAUSE) to redial the number last dialed.
Note
If the number exceeds 32 digits, the beeps will alert you that the number cannot be dialed.
To erase the last phone number dialed
Press (REDIAL/PAUSE) twice.
The number will be erased from the memory, and you’ll hear a long confirmation
beep.
(HANDSET LOCATOR)
Resetting the digital security code
The first time you charge the battery pack, a random security code is automatically
assigned between the base unit and the handset. Only a handset which has this
security code can make calls through the base unit. This system prevents the
possibility of other cordless telephone handsets making calls through your base unit.
You normally do not need to reset the security code. However, in the unlikely event
that you suspect that another cordless phone uses the same security code, you can
manually change the code. Pick up the handset from the base unit, and proceed as
follows:
1
TALK/BATT
LOW lamp
1, 4
Press (PGM).
The TALK/BATT LOW lamp
flashes.
2
Press (#).
You hear a confirmation beep.
3
Press three of the dialing keys
(001 to 999) to store a new code.
4
Press (PGM).
You hear a long confirmation
beep and the TALK/BATT LOW
lamp goes off.
2
5
Immediately replace the handset
on the base unit.
You hear a long confirmation
beep and the phone stores the
new code.
Note
If the battery pack in the handset is completely discharged, or is removed from the handset for
more than several seconds, the digital security code stored will be lost. If this happens, charge the
battery pack and a new security code will be automatically assigned.
Notes on power sources
On battery pack
• Store the battery pack at a temperature between 41°F (5°C) and 95°F (35°C) for
best performance.
• If you do not use the cordless handset for a long period of time, remove the battery
pack.
On power failure
• During a power interruption, you cannot make or receive calls.
For the customers in the USA
RECYCLING NICKEL-CADMIUM BATTERIES
Nickel-Cadmium batteries are recyclable. You can help preserve our
environment by returning your unwanted batteries to your nearest
point for collection, recycling or proper disposal.
Note: In some areas the disposal of nickel-cadmium batteries in
household or business trash may be prohibited.
RBRC (Rechargeable Battery Recycling Corporation) advises you
about spent battery collection by the following phone number.
Call toll free number: 1-800-822-8837 (United States and
Canada only)
Caution: Do not handle damaged or leaking nickel-cadmium batteries.
Troubleshooting
Should any problem persist after you have made these checks, consult your nearest
authorized Sony dealer.
Symptom
Remedy
The handset does not make
or receive a call.
• Reset the digital security code.
• Place the base unit away from noise sources such as TV,
FM radio or PC.
• Make sure the base unit is connected to an AC outlet.
• The battery pack may be discharged. Charge the battery
pack for more than 12 hours.
You hear no dial tone.
• Make sure the telephone line cord is securely connected
to the telephone outlet.
The handset does not
connect at all, even the
numbers you dial are
correct.
• Choose an appropriate dialing mode again.
The handset does not redial
correctly.
• Make sure the number (including the tone and pause
digits, if used) you last dialed is less than 32 digits.
Tip
This procedure will change the code in both the base unit and the handset. The code can be
changed as often as desired.
Mounting the base unit on a wall
1
2
Bundle the loose
telephone line cord
or AC power
adaptor cord, if
necessary.
Wall plate
Telephone
line cord
The handset does not make a • Make sure there is a phone number correctly stored in
speed dialing call.
the speed dialing.
• Store the desired phone number once more.
AC power
adaptor cord
AC outlet
AC power
adaptor
1
Attach the telephone line cord and AC power adaptor cord to the base
unit. Bundle the loose telephone line cord or AC power adaptor cord, if
necessary.
2
Plug the telephone line cord into the telephone outlet, and hook the base
unit to the wall plate as illustrated. Plug the AC power adaptor to an AC
outlet. Then raise the antenna so that it points towards the ceiling.
Maintenance
• Clean the cabinets with a soft cloth slightly moistened with water or a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine as they may damage the finish of the cabinet.
• If the charge terminals of the base unit and handset are soiled, wipe them with a
soft cloth.
If you have any questions or problems concerning your phone, please consult your
nearest Sony dealer.
The handset does not ring.
• Make sure the base unit is connected to an AC outlet.
The handset does not ring
when paging from the base
unit.
• The battery may have little or no power. Charge the
battery pack for more than 12 hours.
• Place the base unit away from noise sources.
You hear a beep every three • Charge the battery pack for more than 12 hours.
seconds and the TALK/
BATT LOW lamp flashes.
The handset does not work.
• The battery pack may be discharged. Charge the battery
pack for more than one minute. After this initial one
minute, you may be able to use the handset, but more
than 12 hours are necessary for full charging.
Specifications
General
Operating frequency
Frequency control
Operation mode
Operation channel
Supplied accessories
902-928 MHz bands
Crystal-controlled PLL
FM, duplex
30 channels
AC power adaptor AC-T127
Telephone line cord
Rechargeable battery pack BP-T50
Handset
Power source
Battery life
Dimensions
Mass
Rechargeable battery pack BP-T50
Standby:
Approx. 30 days
Talk:
Approx. 10 hours
Approx. 2 1/4 × 7 1/8 × 1 15/16 inches (w/h/d), antenna excluded
(approx. 55 × 180 × 48 mm)
Antenna: Approx. 1 15/16 inches (approx. 48 mm)
Approx. 5.5 oz (approx. 155 g), battery included
Base unit
Power source
Battery charging time
Dimensions
Mass
DC 9V from AC power adaptor
Approx. 12 hours
Approx. 4 1/4 × 2 1/8 × 8 3/8 inches (w/h/d), antenna excluded
(approx. 107 × 52 × 212 mm)
Antenna: Approx. 4 5/8 inches (approx. 115 mm)
Approx. 7.6 oz (approx. 215 g)
Design and specifications are subject to change without notice.rencia rápida
Español
Referencia rápida
IMPORTANTES
INSTRUCCIONES DE
SEGURIDAD
A fin de reducir el riesgo de incendio, descarga eléctrica y lesiones a las
personas cuando usted use su equipo telefónico, siempre debe observar
precauciones básicas de seguridad, entre ellas:
1. No use este producto cerca del agua, por ejemplo, cerca de una bañera,
lavabo, fregadero de cocina o lavadora, en un sótano mojado o cerca de
una piscina.
2. Evite usar un teléfono (que no sea del tipo inalámbricos) durante una
tormenta eléctrica. Existe la remota posibilidad de shock eléctrico
debido a rayos.
3. Para notificar una fuga de gas, no utilice el teléfono en la vecindad de
dicha fuga.
4. Utilice solamente el cable de alimentación y las pilas indicados en este
manual. No tire las pilas al fuego. Podrían explotar. Compruebe los
códigos locales con respecto a las instrucciones especiales sobre cómo
deshacerse de ellas.
GUARDE ESTAS
INSTRUCCIONES
INFORMACIÓN PARA LA
DEMANDA DE LA
REGLAMENTACIÓN DE LA
FCC
1. Este equipo cumple con la Parte 15 y la Parte 68 de las reglas de la FCC
para EE.UU. En la base de este equipo hay una etiqueta que contiene,
entre otra información, el número de certificado de la FCC y el número
de equivalencia de timbre de llamada (REN) para este equipo. Cuando
se solicite, esta información deberá ofrecerse a la compañía telefónica.
2. Este equipo se conecta a la red telefónica nacional a través de una toma
telefónica modular cuya toma (conector) de certificado aplicable es
USOC-RJ11C.
3. Con este equipo se suministran un cable telefónico y una clavija
modular que cumplen las normas de la FCC. Este equipo ha sido
diseñado para conectarse a la red telefónica o la instalación de un
usuario utilizando una toma modular compatible que esté de acuerdo
con la Parte 68.
4. El REN se utiliza para determinar la cantidad de dispositivos que
podrán conectarse a la línea telefónica. El exceso de REN conectados
a la línea telefónica puede resultar en que los dispositivos no contesten
a llamadas entrantes. Normalmente, la suma de REN no deberá ser
superior a cinco (5,0). Para enterarse del número total de REN que
puede conectarse a una línea, póngase en contacto con la compañía
telefónica.
5. Si este equipo (SPP-N1000/N1004) produce daños en la red telefónica,
la compañía telefónica le notificará con antelación que es posible que se
requiera la interrupción temporal del servicio. Pero si la notificación
con antelación no es práctica, la compañía telefónica lo notificará al
cliente lo antes posible. Además, se le notificará el derecho a realizar
una reclamación a la FCC si usted lo considera necesario.
6. La compañía telefónica puede realizar cambios en sus instalaciones,
equipos, operaciones, o procedimientos que pueden afectar la operación
del equipo. Cuando suceda esto, la compañía telefónica le avisará con
antelación para que pueda realizar las modificaciones necesarias a fin de
mantener ininterrumpido el servicio.
7. Si experimenta algún problema con este equipo (SPP-N1000/N1004),
con respecto a la reparación o a la información sobre la garantía,
póngase en contacto con Sony Direct Response Center: Tel 1-800-2227669 (EE. UU. solamente). Si el equipo causa problemas en la línea, la
compañía telefónica puede solicitarle que desconecte el equipo hasta
que se resuelva el problema.
8. Todas las reparaciones deberá realizarlas un centro de reparaciones
Sony.
9. Este equipo puede no utilizarse en el servicio de pago previo
proporcionado por la compañía telefónica o la línea compartida.
10. Este equipo es compatible con dispositivos para ayuda a la audición.
Cuando programe números de emergencia y (o) realice llamadas de prueba
a los mismos:
1. Permanezca poco tiempo en la línea y explique a la otra parte la razón
de la llamada.
2. Realice tales actividades en horas no punta, como por la mañana
temprano o a últimas horas de la tarde.
La operación está sometida a las dos condiciones siguientes: (1) Este
dispositivo puede no causar interferencia, y (2) Este dispositivo deberá
aceptar cualquier interferencia, incluyendo la que pueda causar una
operación indeseada.
Precaución
Se le advierte que cualquier cambio o modificación no aprobado
expresamente en el presente manual podría anular su autorización para
operar este equipo.
El secreto de las comunicaciones puede no asegurarse cuando utilice este
teléfono.
Nota
Este equipo se ha sometido a pruebas y se ha determinado que cumple los
límites para un aparato digital Clase B de conformidad con la Parte 15 de
las Reglas FCC. Dichos límites están diseñados para brindar protección
razonable contra interferencia dañina en una instalación residencial. Este
equipo genera, utiliza y puede radiar energía de radiofrecuencia y, si no se
instala y se usa de acuerdo con las instrucciones, puede ocasionar
interferencia dañina en las radiocomunicaciones. Sin embargo, no hay
garantía de que no ocurra interferencia en una instalación específica. En
caso de que este equipo ocasione interferencia dañina en la recepción de
radio o televisión, que se puede determinar apagando y encendiendo el
equipo, se le insta al usuario a que trate de corregir la interferencia mediante
una o más de las siguientes medidas:
– Reorientar o reubicar la antena de recepción.
– Aumentar la separación entre el equipo y el receptor.
– Conectar el equipo en un enchufe de un circuito distinto al circuito al
cual está conectado el receptor.
– Consultar con el distribuidor o con un técnico experimentado de
radio/televisión para ayuda.
Para clientes en EE.UU.
RECICLAJE DE PILAS DE NÍQUEL-CADMIO
Las pilas de níquel-cadmio son reciclables. Puede ayudar a conserval
el medio ambiente devolviendo las pilas que no desee al punto de
recogida o de reciclaje más próximo.
Nota:
En ciertas zonas, el desecho de pilas de
níquel-cadmio en contenedores domésticos o industriales puede estar
prohibido.
La RBRC (Rechargeable Battery Recycling Corporation) le aconsejará
sobre la recogida de pilas usadas en el siguiente número de teléfono:
Llamada gratuita: 1-800-822-8837 (sólo Estados Unidos y
Canadá)
Aviso: No maneje pilas de níquel-cadmio dañadas o con fugas.
Realización de llamadas
Microteléfono
Unidad base
1 Tome el microteléfono de la unidad base.
2 Presione (TALK) y espere hasta que se encienda la lámpara TALK/
BATT LOW.
Después oirá el tono de invitación a marcar. Si oye pitidos, acérquese a
la unidad base.
Marque el número de teléfono.
(FLASH)
Lámpara
TALK/
BATT LOW
Selector
VOL
(TALK)
(OFF)
3
4 Cuando termine de conversar, presione (OFF).
La lámpara TALK/BATT LOW se apagará.
(PGM)
(* TONE)
Recepción de llamadas
(SPEED DIAL)
(REDIAL/PAUSE)
(HANDSET LOCATOR)
1 Cuando suene el teléfono:
Micrófono
• Presione (TALK) (o cualquier tecla excepto (OFF)).
(CHANNEL/RINGER)
o
• Tome el microteléfono de la unidad base si está colocado en ella.
Configuración del teléfono
La lámpara TALK/BATT LOW se encenderá.
3
2 Cuando termine de conversar, coloque el microteléfono en la unidad
base o presione (OFF).
La lámpara TALK/BATT LOW se apagará.
2 Adaptador de alimentación de
CA (AC-T127 suministrado)
Repetición de la marcación
A un tomacorriente
de CA
A DC IN 9V
1 Presione (TALK) y espere hasta que se encienda la lámpara TALK/
BATT LOW.
Enganche el cable.
2 Para repetir la marcación del último número marcado, presione
(REDIAL/PAUSE).
A una toma
telefónica
A LINE
1 Cable de línea telefónica
(suministrado)
1 Conecte el cable de línea telefónica a la toma LINE y a una toma
2
3
telefónica.
Conecte el adaptador de alimentación de CA a la toma DC IN 9V y a un
tomacorriente de CA.
Levante la antena. Cerciórese de que quede apuntando hacia el techo.
Nota
Utilice solamente el adaptador de alimentación de CA AC-T127 suministrado. No emplee ningún
otro adaptador de alimentación de CA.
Preparación de la batería
La lámpara TALK/BATT LOW parpadeará.
Presione (SPEED DIAL).
2
3 Presione una de las teclas de marcación ((0) a (9)) para almacenar un
4
número de teléfono en ella.
Usted oirá un pitido de confirmación.
Introduzca el número de teléfono que desee almacenar.
Usted podrá introducir hasta 20 dígitos, incluyendo un tono y una pausa,
cada uno de los cuales se contará como un dígito.
5 Presione (PGM).
Realización de llamadas con la
marcación abreviada
Rojo
Negro
Lámpara LINE/CHARGE
La lámpara LINE/CHARGE se encenderá cuando el microteléfono esté
completamente asentado en los terminales de la unidad base. Cargue la
batería durante más de 12 horas a fin de que quede completamente
cargada. La lámpara LINE/CHARGE permanecerá encendida incluso
aunque haya terminado la carga.
Una batería completamente cargada durará aproximadamente 10 horas cuando utilice
continuamente el microteléfono/30 días con el microteléfono en el modo de espera.
Elección del modo de marcación
1 Presione (PGM).
La lámpara TALK/BATT LOW parpadeará.
2 Presione (* TONE).
Usted oirá un pitido de confirmación.
3 Presione (1) para la marcación por pulsos o (2) para la marcación por
4 Presione (PGM).
1 Presione (PGM).
Usted oirá un pitido largo de confirmación, y el número se almacenará.
La lámpara TALK/BATT LOW se apagará.
BP-T50
tonos.
Almacenamiento de números de
teléfono
1 Presione (TALK) y espere hasta que se encienda la lámpara TALK/
BATT LOW.
2 Presione (SPEED DIAL).
3 Introduzca el número de marcación abreviada deseado ((0) a (9)).
El número de teléfono almacenado en las teclas de marcación abreviada
se marcará.
Localización del microteléfono
Presione (HANDSET LOCATOR).
El microteléfono sonará durante unos minuto.
Para terminar la llamada buscapersonas, presione (OFF) del microteléfono.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement