Sony Radio SRF-M80V User manual

Sony Radio SRF-M80V User manual
3-239-332-21(1)
Notes on Headphones
Installing the Batteries
Road safety
TV/WEATHER/FM Stereo/AM
PLL Synthesized Radio
Operating Instructions
TV/WEATHER/FM/AM WALKMAN
Do not use headphones while driving, cycling, or operating any
motorized vehicle. It may create a traffic hazard and is illegal in
many areas. It can also be potentially dangerous to play your
headphones at high volume while walking, especially at pedestrian
crossings. You should exercise extreme caution or discontinue use in
potentially hazardous situations.
(See Fig. A– )
Preventing hearing damage
2
Avoid using headphones at high volume.
Hearing experts advise against continuous, loud and extended play.
If you experience a ringing in your ears, reduce volume or
discontinue use.
SRF-M80V
Caring for others
Sony Corporation ©2002 Printed in China
Keep the volume at a moderate level. This will allow you to hear
outside sounds and to be considerate to people around you.
Warning
If there is lightning when you are using the unit, take off the
headphones immediately.
For customers in the USA
Please register this product on line at
http://www.sony.com/productregistration.
Proper registration will enable us to send you periodic mailings
about new products, services, and other important announcements.
Registering your product will also allow us to contact you in the
unlikely event that the product needs adjustment or modification.
Thank you.
WARNING
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
This device complies with the Part 15 of the FCC Rules.
Operation is subject to the condition that this device does not
cause harmful interference.
Trade Name:
Model name:
SONY
SRF-M80V
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
If you have any questions about the product, you may call:
Sony Direct Response Center 1-(800)-222-7669 or write to:
Sony Direct Response Center 12451 Gateway Blvd. Fort Myers, FL
33913
Declaration of Conformity
SONY
SRF-M80V
Sony Electronics Inc.
680 Kinderkamack Road, Oradell, NJ 07649
USA
Telephone Number: 201-930-6972
Trade Name:
Model:
Responsible Party:
Address:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Before You Begin
Thank you for choosing the Sports Walkman radio!
It will give you many hours of reliable service and listening pleasure.
Before operating the radio, please read these instructions thoroughly and
retain them for future reference.
Features
• TV/WEATHER/FM/AM 4 band PLL (phase locked loop) synthesized
armband radio.
• Easy Preset Digital Tuning with 25 memory presets.
• 5 direct presets calls and 1 direct weather-band button.
• Stopwatch, split and pitch timer functions.
• Wearable round design for armband and belt-holder use.
• Water-resistant for all –weather use.
• MEGA BASS for dynamic bass sound.
Notes on AM Channel Step
The AM channel step differs depending on areas. See “Changing AM
Channel Step”.
Precautions
• Operate the unit only on 3 V DC with two size AAA (R03) batteries.
• Avoid exposure to temperature extremes, direct sunlight, moisture,
sand, dust or mechanical shock. Never leave the unit in a car parked
under the sun.
• Should anything fall into the unit, remove the batteries and have the
unit checked by qualified personnel before operating it any further.
• To clean the casing, use a soft cloth dampened with a mild detergent
solution.
• In vehicles or buildings, radio reception may be difficult or noisy. Try
listening near a window.
1
Open the battery compartment lid and install two size AAA
(R03) batteries (not supplied) with correct polarity.
When batteries are first installed, “AM 12:00” flashes in the display.
Once the current time is set, the flashing stops.
Close the lid.
Battery Life (Approx. hours)
When using
TV
Sony alkaline
28
size AAA (LR03)
Sony size AAA (R03)
11
FM
(JEITA*)
AM
28
30
50
11
12
30
WEATHER
* Measured by JEITA (Japan Electronics and Information Technology
Industries Association) standards. The actual battery life may vary
depending on the circumstance of the unit.
When to replace the batteries
You can check the remaining battery power that appears in the display.
The indicators are as follows:
Notes on batteries
• Do not charge the dry batteries.
• Do not carry the dry batteries together with coins or other metallic
objects. It can generate heat if the positive and negative terminals of the
batteries are accidentally come into contact with metallic objects.
• When you are not going to use the unit for a long time, remove the
batteries to avoid damage from battery leakage and corrosion.
• Do not use different types of batteries at the same time.
• When you replace the batteries, replace all with new ones.
To attach the battery compartment lid if it is
accidentally detached (See Fig. A– )
The battery compartment lid is designed to come off when opened with
excessive force. To put it back on, see the illustration.
1
2
Insert one side of the lid as illustrated.
Push the other side to attach.
A
Insert the # side
of the battery first.
Indicator
Cautions on Water-resistance
This unit is designed so that it can be used with slight exposure to rain,
snow and other forms of moisture, but there are several points on which
caution should be observed.
• Do not allow it to come in contact with large amounts of water.
• Do not immerse it in water.
• If water should get on it or if it should fall into water, take it out
immediately and wipe it off with a dry cloth. The interior of the
battery compartment has no water-resistance. The battery may
corrode, so wipe out the interior of the battery compartment as follows.
– Open or close the battery compartment with dry hands in a place
without exposure to any water.
– Wipe off the battery and the inside of the battery compartment. Give
special attention to the contacts so that no water remains on them.
If you have any questions or problems concerning your unit,
please consult your nearest Sony dealer.
Troubleshooting Guide
Should any problem persist after you have made the following checks,
consult your nearest Sony dealer.
All buttons do not operate at all.
• “-” is displayed. Slide down the HOLD lever so that “-” disappears.
Very weak or interrupted sound, or unsatisfactory reception
• Weak batteries
• In a vehicle or in a building, move closer to a window.
Display is dim, or no indication is displayed.
• Weak batteries.
• The unit is being used in extremely high or low temperatures or in a
place with excessive moisture.
The station cannot be received when a PRESET TUNING (1 to 5)
button is pressed.
• You chose the wrong preset number.
• The memory of the station has been initialized. Preset the station again.
” is flashing in the
The power cannot be turned on, and “
display.
• The batteries have been completely exhausted.
The preset stations may be initialized, if a maintenance service is
performed.
Please note down your settings in case you want to preset them again.
Specifications
Time display
12-hour system
Frequency range
Band
Range
Channel step
TV
2 - 13 ch
1 channel
WEATHER
1 - 7 ch
1 channel
FM
87.5 – 108 MHz
0.1 MHz
AM
530 – 1 710 kHz
10 kHz
Output
i (headphones) jack (ø 3.5 mm, stereo minijack) 16 Ω
Power output
15 mW + 15 mW (at 10 % harmonic distortion)
Power requirements
3 V DC, two size AAA (R03) batteries
Dimensions
Approx. 69.2 × 45 × 113.5 mm (w/h/d)
(2 3/4 × 1 13/16 × 4 1/2 inches) incl. projecting parts and controls
Mass
Approx. 104.2 g (3.68 oz.) incl. batteries
Accessories Supplied
Stereo headphones (vertical in the ear type) (1)
Arm band (1)
Design and specifications are subject to change without notice.
x
x
Full strength*
Weakening*
When the battery becomes exhausted, the unit will turn off.
Replace with new batteries. When you press POWER after
installing the new batteries, the indicator changes to
”.
“
* Displayed only when the radio is turned on.
Note
Do not take more than 40 seconds to replace the batteries, otherwise, your
clock, pitch timer and countdown timer settings and preset stations will
be initialized. Should that happen, reset the functions again.
Size AAA (R03) x 2
Using the Arm Band
PRESET TUNING 1
to 5*
MEGA BASS
1
2
3
SPLIT/RESET
4
(See Fig. B– )
Radio frequency*
Slide the connector onto the unit until you hear a click.
Unwind and straighten the wraparound arm band.
WB
ENTER
TUNE/TIME SET +/–*
BAND
MODE
* The TUNE/TIME SET +
and the PRESET
TUNING 3 buttons
have a tactile dot.
B
There is a tactile dot
beside volume to show
the direction to turn up
the volume.
)
To switch to the other modes during counting, press MODE.
While holding down “PUSH RELEASE” (1), slide the connector to
remove the arm band (2).
Playing the Radio
The arm band can be attached either on left or right arm by changing up
side down. The unit can also be removed with the arm band attached on
your arm, as instructed above.
— Manual Tuning
1 Connect the headphones to the i (headphones) jack.
2 Press POWER to turn on the radio.
)
3
— HOLD Function
Slide up HOLD lever to the direction of the arrow.
“-” appears in the display to indicate all buttons are locked.
To cancel HOLD, slide down HOLD lever to the opposite direction of the
arrow.
“-” disappears in the display.
Setting the Clock
The display will flash “AM 12:00” when the batteries are first inserted.
1
2
Rubber belt
Wraparound
arm band
Press MODE repeatedly to select the clock mode when the
clock mode is not on.
Hold down ENTER for more than 2 seconds.
The beep sounds and the hour flashes in the
display.
3
4
Rubber belt
Press TUNE/TIME SET + or – until the correct hour appears
in the display.
Each press changes the digit(s) by one.
When you keep the button pressed, the digit(s) change rapidly.
Press ENTER.
FM2
TV
To change the band to WEATHER, press WB. You can return to the
previous frequency by pressing BAND.
FM1 and FM2 are differentiated only for Preset tuning. For Manual
tuning of FM stations, select either band.
4
5
Displaying the Split Time
To display the current split time, press SPLIT/RESET while the stopwatch
is running. “SPLIT” flashes in the display.
The stopwatch keeps counting during the display.
To return to the count display, press SPLIT/RESET again while the split
time is being displayed.
Using the Pitch Timer
Press TUNE/TIME SET + or – to tune in to the desired station.
1
Two short beeps sound when the minimum frequency of each band is
received during tuning.
Adjust the volume using VOL.
To turn off the radio, press POWER.
2
3
Improving the Reception
FM: Extend the headphones cord which functions as the
FM antenna (See Fig. C- ).
AM: Rotate the unit horizontally for optimum reception.
A ferrite bar antenna is built-in the unit
(See Fig.C- ).
Set TV/WB/FM SENS to LOCAL if interference is
prevalent and reception is too strong. Under normal
conditions, set it to DX.
4
5
6
7
Presetting a station
1 Follow steps 1 to 4 in “Playing the Radio” and manually tune
2
in to the station you wish to preset.
Press the PRESET TUNING button you wish to preset for
more than a few seconds.
You will hear two confirmation beeps and preset number appears in
the display.
To preset another station, repeat these steps.
To change the preset station, tune in to the desired station and hold
down the PRESET TUNING 1 to 5 button. The new station will replace
the previous station on the preset button.
Example: Display window when you preset FM
90.0 MHz in the PRESET TUNING 2 button
for FM2.
Tuning in a Preset Station
1 Press POWER.
2 Press BAND or WB to select the band.
3 Press the desired PRESET TUNING button.
4 Adjust the volume using VOL.
“PITCH” flashes in the display.
Hold down ENTER for more than 2 seconds.
The beep sounds and the countdown duration
flashes in the display.
Press TUNE/TIME SET + or – to set the desired countdown
duration for the pitch timer.
The countdown duration can be set from 1 second to 59 minutes 59
seconds, in 1-second increments.
Press ENTER.
Press TUNE/TIME SET + or – to set the desired number of
times.
The number of times can be set up to 99.
Press ENTER.
The two beeps sound and the number of times stops flashing.
Press START/STOP.
Countdown starts. After the preset countdown duration, the two
beeps sound three times.
“MEGA BASS” indication appears in the display when the MEGA BASS
function is on.
The MEGA BASS function intensifies the bass sound for richer quality
audio reproduction.
— Preset Tuning
Press MODE to select the pitch timer.
The beep sounds and the number of times flashes in
the display.
Press MEGA BASS.
Channel step
10kHz
9kHz
Two short beeps sound, and the AM channel step will be changed.
“AM 9” (or “AM 10”) is displayed for about 2 seconds.
If you proceed to step 3 again, the channel step changes again.
To listen to the radio while the stopwatch is running, press POWER. The
display will switch to the radio frequency for a few seconds.
Each band memorizes the frequency you had tuned previously.
You can preset up to 10 stations in FM (5 stations in FM1, 5 stations in
FM2), and 5 stations in each AM, TV, WEATHER.
Press POWER to turn off the power.
Press MODE repeatedly to select the clock mode when the
clock mode is not on.
While holding down TUNE/TIME SET + or –, keep pressing
MODE for more than 5 seconds.
“STPW” stops flashing if changed to other mode while the stopwatch
counts down.
The pitch timer allows setting the timer with an identical length of time
repeatedly. The functions of the radio, the stopwatch, and the countdown
timer are available even while the pitch timer is being used.
12-hour system: “AM 12:00” = midnight
“PM 12:00” = noon
Note
When the AM channel step is changed, the preset stations for AM will be
initialized.
3
FM1
Presetting Your Favorite Station
Area
North and South American countries
Other countries
D
AM
The beep sounds and the minute starts to flash.
Repeat step 3 to set the minute. After setting the
minute, press ENTER again. The two beeps sound
and the clock starts from 0 seconds.
The AM channel step differs depending on areas. The channel step of this
unit is factory-set to 10 kHz. Change the settings as shown below to be
able to listen to the radio.
1
2
Press BAND to select the band.
Enhancing Bass Sound
Changing AM Channel Step
C
“RADIO ON” appears in the display.
Each press changes the band as follows:
Caution (See Fig. B– )
• Avoid bending the wraparound band forcibly in the opposite direction.
It may break.
• The straightened band will wind easily when you touch or wiggle it. Be
sure to treat it carefully.
Preventing Accidental Change
Connector
When the count time exceeds “59:59 99” during the minute-second-split
second display, the display switches to the hour-minute-second display.
* Selected only when the power is on.
If the rubber belt and wraparound band becomes dirty
Remove the rubber belt from the unit and clean them.
VOL
Pitch timer
Countdown timer
Tighten the band with the rubber belt.
Belt clip
i (headphones) jack
To reset to zero, press SPLIT/RESET when the stopwatch is in the stop
status.
The stopwatch comes with two display modes. To switch to the hourminute-second display, press ENTER.
To switch to the minute-second-split second display, press ENTER again.
The band will wind by itself.
To vary the length of the rubber belt to fit your arm (See Fig. B–
Move the velcro fastener to the proper position.
TV/WB/FM SENS
DX/LOCAL
Stopwatch
Press START/STOP to stop.
Hold the body of the unit and attach the straightened band to
your arm.
To remove the arm band from the unit (See Fig. B–
HOLD lever
Clock
To more easily straighten the band, slightly bend the tip of the band in
the opposite direction.
START/STOP
POWER
3
Press MODE to select a function mode.
Each function mode can be selected as follows:
When the last pitch timer setting is finished, the display switches to
the pitch timer display even in another display mode and a long beep
sounds, and then returns to the previous display.
To stop the long beep, press any button.
To pause the countdown on the pitch timer, press START/STOP while
counting down.
At this time, the countdown is reset by pressing SPLIT/RESET. The display
will show the set-up countdown duration and number of times.
To switch to the other modes, press MODE.
“PITCH” stops flashing if changed to other mode while the pitch timer
counts down.
Using the Countdown Timer
You can use the built-in countdown timer to turn off the radio
automatically after a preset duration.
1
2
3
4
5
Press MODE to select the countdown timer.
“TIMER” flashes in the display.
Hold down ENTER for more than 2 seconds.
The beep sounds, and the countdown duration starts flashing.
Press TUNE/TIME SET + or – to set the desired countdown
duration for the timer.
The countdown duration can be set from 1 minute to 2 hours, in 1minute increments.
Press ENTER.
The two beeps sound and the countdown duration stops flashing.
Press START/STOP.
Countdown starts. The radio is automatically turned on when the
radio is off. After the preset countdown duration, the four beeps
sound five times and the radio is turned off.
To stop the beeps, press any button.
To turn off the radio before the preset time, press POWER.
Selecting the Mode
Note
Holding down the desired PRESET TUNING button for more than a few
seconds will replace the previous station on the PRESET TUNING button
with the station you tuned in to.
You can use this unit as a radio, clock, stopwatch, pitch timer or
countdown timer.
The functions of clock, stopwatch, pitch timer, countdown timer are
available even if the power is off.
Using the Stopwatch
To switch to the other modes, press MODE.
“TIMER” stops flashing if changed to other mode while the countdown
timer counts down.
The stopwatch can time up to 99 hours 59 minutes and 59.99 seconds, in
1/100-second increments.
1
2
Press MODE to select the stopwatch.
“STPW” flashes in the display.
Press START/STOP to start.
The display shows the elapsed time.
To pause the countdown on the countdown timer, press START/STOP
while counting down.
At this time, the countdown is reset by pressing SPLIT/RESET. The display
will show the set-up countdown duration.
Using the Belt Clip
(See Fig. D)
Use the belt clip when attaching the unit to your belt.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement