Sony Car Speaker SA-NS310 Operating instructions

Add to my manuals
60 Pages

advertisement

Sony Car Speaker SA-NS310 Operating instructions | Manualzz
Network Speaker
Getting Started
Network Connections
Operating Instructions
Listening to Audio Content
Over Your Home Network
Using Internet music
streaming (Music Service)
Using AirPlay
Using Music Throw
Others
Troubleshooting
SA-NS310/NS410
WARNING
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
To reduce the risk of fire, do not cover the
ventilation opening of the apparatus with
newspapers, tablecloths, curtains, etc.
Do not place the naked flame sources such as lighted
candles on the apparatus.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing, and
do not place objects filled with liquids, such as
vases, on the apparatus.
As the main plug is used to disconnect the unit from
the mains, connect the unit to an easily accessible
AC outlet. Should you notice an abnormality in the
unit, disconnect the main plug from the AC outlet
immediately.
Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or
the like.
The unit is not disconnected from the mains as long
as it is connected to the AC outlet, even if the unit
itself has been turned off.
The dating code and the nameplate are located on the
bottom exterior. (For USA and Canada)
The nameplate is located on the bottom exterior.
(For Europe)
On the battery for the remote
control
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent
type.
Replace the battery with a Sony CR2025 lithium
battery.
Use of another battery may present a risk of fire or
explosion.
2GB
For customers in the United
States and Canada
Owner’s Record
The model and serial numbers are located on the
bottom of the unit. Record these numbers in the
space provided below. Refer to them whenever you
call upon your Sony dealer regarding this product.
Serial No.
Model No.
For customers in the United
States
Important Safety Instructions
1)
2)
3)
4)
5)
6)
7)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10)Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11)Only use attachments/accessories specified by
the manufacturer.
12)Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13)Unplug this apparatus during lightning storms or
when unused for long periods of time.
14)Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
The following FCC statement applies only to the
version of this model manufactured for sale in the
U.S.A. Other versions may not comply with FCC
technical regulations.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
This equipment must not be co-located or operated
in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency
(RF) Exposure Guidelines in Supplement C to
OET65.
This equipment should be installed and operated
keeping the radiator at least 20 cm or more away
from person’s body (excluding extremities: hands,
wrists, feet and ankles).
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate this equipment.
Properly shielded and grounded cables and
connectors must be used for connection to host
computers and / or peripherals in order to meet FCC
emission limits.
3GB
For the State of California,
USA only
Perchlorate Material - special handling may apply,
See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Perchlorate Material: Lithium battery contains
perchlorate.
For customers in Canada
Properly shielded and grounded cables and
connectors must be used for connection to host
computers and / or peripherals.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2)
this device must accept any interference, including
interference that may cause undesired operation of
this device.
This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment and
meets RSS-102 of the IC radio frequency (RF)
Exposure rules.
This equipment should be installed and operated
keeping the radiator at least 20 cm or more away
from person's body (excluding extremities: hands,
wrists, feet and ankles).
For customers in Europe
Notice for customers: the following information is
only applicable to equipment sold in countries
applying EU directives.
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku Tokyo,
108-0075 Japan.
The Authorized Representative for EMC and
product safety is Sony Deutschland GmbH,
Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to
the addresses given in separate service or guarantee
documents.
This equipment has been tested and found to comply
with the limits set out in the EMC Directive using a
connection cable shorter than 3 meters.
Hereby, Sony Corp., declares that this equipment is
in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
For details, please access the following URL:
http://www.compliance.sony.de/
This product is intended to be used in the following
countries.
AT,BE,DK,FI,FR,DE,IS,IT,LU,NL,NO,ES,SE,CH,
GB,PL
Notice for the customers in France
The WLAN feature of this Network Speaker shall
exclusively be used inside buildings.
Any use of the WLAN feature of this Network
Speaker outside of the buildings is prohibited on the
French territory. Please make sure that the WLAN
feature of this Network Speaker is disabled before
any use outside of the buildings.(ART Decision
2002-1009 as amended by ART Decision 03-908,
relating to radio-frequencies use restrictions).
4GB
Notice for the customers in Italy
Use of the RLAN network is governed:
– with respect to private use, by the Legislative
Decree of 1.8.2003, no. 259 (“Code of Electronic
Communications”). In particular Article 104
indicates when the prior obtainment of a general
authorization is required and Art. 105 indicates
when free use is permitted;
– with respect to the supply to the public of the
RLAN access to telecom networks and services,
by the Ministerial Decree 28.5.2003, as amended,
and Art. 25 (general authorization for electronic
communications networks and services) of the
Code of electronic communications.
Notice for the customers in Norway
Use of this radio equipment is not allowed in the
geographical area within a radius of 20 km from the
centre of Ny-Ålesund, Svalbard.
Disposal of Old
Electrical & Electronic
Equipment (Applicable
in the European Union
and other European
countries with
separate collection systems)
This symbol on the product or on its packaging
indicates that this product shall not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. The recycling of materials
will help to conserve natural resources. For more
detailed information about recycling of this product,
please contact your local Civic Office, your
household waste disposal service or the shop where
you purchased the product.
Disposal of waste
batteries (applicable
in the European Union
and other European
countries with separate
collection systems)
This symbol on the battery or on the packaging
indicates that the battery provided with this product
shall not be treated as household waste.
On certain batteries this symbol might be used in
combination with a chemical symbol. The chemical
symbols for mercury (Hg) or lead (Pb) are added if
the battery contains more than 0.0005% mercury or
0.004% lead.
By ensuring these batteries are disposed of correctly,
you will help prevent potentially negative
consequences for the environment and human health
which could otherwise be caused by inappropriate
waste handling of the battery. The recycling of the
materials will help to conserve natural resources.
In case of products that for safety, performance or
data integrity reasons require a permanent
connection with an incorporated battery, this battery
should be replaced by qualified service staff only.
To ensure that the battery will be treated properly,
hand over the product at end-of-life to the applicable
collection point for the recycling of electrical and
electronic equipment.
For all other batteries, please view the section on
how to remove the battery from the product safely.
Hand the battery over to the applicable collection
point for the recycling of waste batteries.
For more detailed information about recycling of
this product or battery, please contact your local
Civic Office, your household waste disposal service
or the shop where you purchased the product.
For customers in Australia and New
Zealand
This equipment should be installed and operated
with at least 20 cm and more between the radiator
and person’s body (excluding extremities: hands,
wrists, feet and ankles).
5GB
On the illustrations in this
manual
The illustrations and screen shots used in this
manual are of the SA-NS310 unless noted
otherwise.
6GB
Table of Contents
Features of this unit ...................................... 8
Setting up your home network ..................... 9
Getting Started
Guide to Parts and Controls ....................... 10
Main unit of SA-NS410 ........................ 10
Main unit of SA-NS310 ........................ 13
Remote control ...................................... 16
Checking the Supplied Accessories ........... 17
Preparing the Unit and the Remote
Control .................................................. 17
Connecting to an AC power source ...... 17
Preparing the remote control ................. 18
Turning the Unit On ................................... 18
Using Internet music
streaming (Music Service)
Using Internet music streaming ..................29
Preparing your mobile device instead of the
remote control ........................................29
Enjoying Internet music streaming ........30
Using AirPlay
Using AirPlay .............................................32
Using Music Throw
Using Music Throw on a Sony Tablet ........34
Network Connections
Others
How to Connect Your Network ................. 20
Setting Up for a Wireless Network ............ 20
Option 1: Method for using a supplied
CD-ROM and Windows PC .................. 20
Option 2: Method for using an application
for smartphones or Tablets (Android
device/iPhone/iPod touch/iPad) ............ 21
Option 3: Manual setting method using an
Access Point Scan (for PC/Mac) ........... 22
Option 4: Method for using a WPS push
button at the access point supporting
WPS ...................................................... 23
Setting Up Wired Networks ....................... 24
Option 5: DHCP method ....................... 24
Using the PARTY STREAMING ..............35
Starting a PARTY .................................35
Joining a PARTY ..................................35
Updating software ......................................36
Setting Screen on the Browser ...................37
Using the setting screen on the
browser ..................................................37
Starting the browser with
Windows XP .........................................38
Specifications .............................................39
Precautions .................................................41
Troubleshooting
Troubleshooting ..........................................42
Indicator information .............................47
Listening to Audio Content
Over Your Home Network
Using DLNA (Digital Living Network
Alliance) ................................................ 25
Listening to audio content on a computer
with Windows 7 .................................... 25
Listening to audio content on a computer
with Windows Vista/Windows XP ....... 27
7GB
Features of this unit
You can enjoy music from anywhere in your home by connecting this DLNA (Digital Living
Network Alliance)-compliant unit to a network. For example, you can listen to audio content
stored on the computer in the bedroom, through this unit in the living room (page 25).
Internet music streaming
You can enjoy Internet music streaming, using “Network Audio Remote*” application without
a PC. This application allows your Android phone/Sony Tablet/iPhone/iPod touch/iPad to be
used as a music controller (page 29).
Control
Access
Deliver
Internet
Music on your PC
You can play audio on a Mac or Windows PC with iTunes (page 32) or Windows Media Player
(page 25).
AirPlay
You can play audio on an iPhone, iPod touch or iPad. You can also control audio content from
anywhere in your home (page 32).
Music Throw by Sony Tablet
You can stream your music to the network speaker directly, using the built-in music player of
a Sony Tablet (page 34).
PARTY STREAMING
PARTY STREAMING allows you to play back the same audio content through speakers
having the PARTY STREAMING function at the same time (page 35).
Analog input supported
You can use this unit as a general active speaker without connecting to a network.
8GB
Listening to the music from a server
You can enjoy your favorite music content from your DLNA-compliant server (computer, etc.)
by controlling the server using “Network Audio Remote” application. For details, see page 25.
Device with Network Audio Remote* or DLNA controller
Control
* Sony provides the “Network
Audio Remote” application for
free.
For details, refer to the following
website:
http://www.sony.net/sans
Access
Deliver
Server
Network controlled player (this unit)
You can listen to audio content through only this unit by using a computer as both server and
controller. Windows 7 has to be installed on your computer to use this function. For details, see
page 25.
Deliver
DLNA controller/Server
(Windows 7-based computer)
Network controlled player (this unit)
Setting up your home network
Refer to the following pages according to your network environment.
Wireless networks
. Set up your network, using the supplied CD-ROM or an application for
smartphones. Refer to the leaflet “Quick Start Guide” for details. When you set
up your network manually, see page 20.
WPS* compliant wireless networks
. Page 23
Wired networks
. Page 24
* WPS is a standard for easy and secure establishment of a wireless home network. Many
new wireless LAN router/access point come with this feature.
9GB
Getting Started
Guide to Parts and Controls
Main unit of SA-NS410
Front
For details on each indicator, see “Indicator information” (page 47).
A PARTY button
Press to use the PARTY STREAMING
function (page 35).
Tip
This button also receives signals from a remote
control.
Aim the remote control at this point.
The remote signal reception of this unit may not
work correctly when the surface of this button is
dirty.
B PARTY STREAMING indicator
Indicates the PARTY STREAMING status
(page 35).
Green: The unit is having a PARTY as
PARTY host.
Amber: The unit has joined a PARTY as
PARTY guest.
Red: An error has occurred.
10GB
C Illumination indicator
Indicates the playback status of audio
content.
Blue (lit): The unit has stopped playing
back audio content.
White (lit): The unit is in playback mode.
White (flashing): The unit is in preparation
for playback.
An error has occurred in the playback if it
is flashing quickly.
Note
This indicator flashes during start up. It
may take for a while.
Side
For details on each indicator, see “Indicator information” (page 47).
Getting Started
D ?/1 (ON/Standby) button, indicator
Press to switch between power on and the
standby mode (page 18).
Indicates the power status of the unit
(page 18).
Green: The unit is turned on.
Amber: The unit is in the network standby
mode.
Red: The unit is in the standby mode.
E AUDIO IN button, indicator1)
Press to switch the audio input on or off.
Lights in green when the audio input is on.
F UPDATE button, indicator
Press to start updating the software of the
unit (page 36).
Indicates the update status of the unit.
Green (lit): The unit can be updated.
Green (flashing): The unit is updating.
Red (flashing): An error has occurred.
Not lit: The unit does not need updating.
G LINK indicator
Indicates the connection status of the
wired/wireless LAN.
Green: Wireless connection (page 20).
Amber: Wired connection (page 24).
Red: The following status have occurred.
– This unit cannot find the wireless
LAN access point.
– The security method/password
selected for the access point is wrong.
– An error has occurred.
Not lit: The wireless network setting
process is not finished.
H VOL +2)/– buttons
Use to adjust the volume. The illumination
indicator flashes rapidly when the volume
level is set to either minimum or
maximum.
1)
Home network/AirPlay/Internet music streaming
is selected automatically when the AUDIO IN
indicator is off.
2)
The VOL+ button has a tactile dot. Use it as a
reference point for operations.
11GB
Back
For details on each indicator, see “Indicator information” (page 47).
I DC IN terminal
Use to connect the supplied AC adaptor
(page 17).
Rated output voltage of an AC adaptor: DC
18 V, 2.6 A
Note
The supplied AC adaptor and AC power cord
are exclusive for this unit. Do not use an AC
adaptor not supplied with this unit.
J WPS button
Use to make the network settings for the
WPS push button configuration (page 23).
K AUDIO IN terminal
Use to connect the audio output jack of an
external component.
L
(LAN) port
Use to connect the network (LAN) cable
(not supplied).
M NETWORK STANDBY / STANDBY
switch
Switch between the network standby mode
and the standby mode (page 19).
12GB
N ALL RESET button (Bottom)
Press and hold until all indicators light
while the unit is being turned on and reset
to its factory default settings.
Use a thin object, such as a small pin.
The previously registered settings or
information will be reset.
Note
Network settings are also reset when you
press ALL RESET button.
ALL RESET
button
Bottom
Main unit of SA-NS310
Front
For details on each indicator, see “Indicator information” (page 47).
Getting Started
A PARTY STREAMING indicator
Indicates the PARTY STREAMING status
(page 35).
Green: The unit is having a PARTY as
PARTY host.
Amber: The unit has joined a PARTY as
PARTY guest.
Red: An error has occurred.
B PARTY button
Press to use the PARTY STREAMING
function (page 35).
Tip
This button also receives signals from a remote
control.
Aim the remote control at this point.
The remote signal reception of this unit may not
work correctly when the surface of this button is
dirty.
C Illumination indicator
Indicates the playback status of audio
content.
Blue (lit): The unit has stopped playing
back audio content.
White (lit): The unit is in playback mode.
White (flashing): The unit is in preparation
for playback.
An error has occurred in the playback if it
is flashing quickly.
Note
This indicator flashes during start up. It
may take for a while.
13GB
Side
For details on each indicator, see “Indicator information” (page 47).
D LINK indicator
Indicates the connection status of the
wired/wireless LAN.
Green: Wireless connection (page 20).
Amber: Wired connection (page 24).
Red: The following status have occurred.
– This unit cannot find the wireless
LAN access point.
– The security method/password
selected for the access point is wrong.
– An error has occurred.
Not lit: The wireless network setting
process is not finished.
E ?/1 (ON/Standby) button, indicator
Press to switch between power on and the
standby mode (page 18).
Indicates the power status of the unit
(page 18).
Green: The unit is turned on.
Amber: The unit is in the network standby
mode.
Red: The unit is in the standby mode.
F AUDIO IN button, indicator1)
Press to switch the audio input on or off.
Lights in green when the audio input is on.
14GB
G VOL +2)/– buttons
Use to adjust the volume. The illumination
indicator flashes rapidly when the volume
level is set to either minimum or
maximum.
H
(LAN) port
Use to connect the network (LAN) cable
(not supplied).
I AUDIO IN terminal
Use to connect the audio output jack of an
external component.
J DC IN terminal
Use to connect the supplied AC adaptor
(page 17).
Rated output voltage of an AC adaptor: DC
13 V, 2 A
Note
The supplied AC adaptor and AC power cord
are exclusive for this unit. Do not use an AC
adaptor not supplied with this unit.
1)
Home network/AirPlay/Internet music streaming
is selected automatically when the AUDIO IN
indicator is off.
2)
The VOL+ button has a tactile dot. Use it as a
reference point for operations.
Bottom
For details on each indicator, see “Indicator information” (page 47).
Getting Started
K NETWORK STANDBY / STANDBY
switch
Switch between the network standby mode
and the standby mode (page 19).
L WPS button
Use to make the network settings for the
WPS push button configuration (page 23).
M UPDATE button, indicator
Press to start updating the software of the
unit (page 36).
Indicates the update status of the unit.
Green (lit): The unit can be updated.
Green (flashing): The unit is updating.
Red (flashing): An error has occurred.
Not lit: The unit does not need updating.
N ALL RESET button
Press and hold until all indicators light
while the unit is being turned on and reset
to its factory default settings.
Use a thin object, such as a small pin.
The previously registered settings or
information will be reset.
Note
Network settings are also reset when you
press ALL RESET button.
15GB
Remote control
VOLUME
MUTING
A DIMMER button
Press to change the brightness of the
illumination indicator (normal/dark).
B INPUT button
Press to switch the audio input on or off.
C PARTY button
Press to use the PARTY STREAMING
function (page 35).
D VOLUME +/– buttons
Press to adjust the volume.
E MUTING button
Press to turn the sound off temporarily.
The illumination indicator blinks in blue
during muting.
F ?/1 (ON/Standby) button
Press to switch between power on and the
standby mode (page 18).
16GB
2
Checking the Supplied
Accessories
Plug the connector of the AC
adaptor into the DC IN terminal
on the unit.
SA-NS410
Make sure that the following items are
included in the package along with the
speaker.
Getting Started
Remote control (1)
AC adaptor (1)
AC power cord (1)
CD-ROM (“NS Setup”) (1)
Operating Instructions (this manual)
Quick Start Guide (Leaflet)
SA-NS310
Preparing the Unit and
the Remote Control
Connecting to an AC power
source
1
Connect the AC power cord to
the AC adaptor.
3
Plug the AC power cord to a
wall outlet (the mains).
AC power cord
AC adaptor
17GB
Preparing the remote control
The supplied lithium battery (CR2025) has
already been inserted into the remote control.
Pull out the protective sheet before use.
Turning the Unit On
Make sure the unit is connected to
an AC power source (page 17).
The ?/1 (ON/Standby) indicator flashes in
green and the illumination indicator lights.
You can operate this unit when the ?/1 (ON/
Standby) indicator lights in green and the
illumination indicator lights. It may take a
while.
SA-NS410
Replacing the battery of the
remote control
If the remote control stops working, replace
the battery (CR2025) with a new one.
SA-NS310
1 Pull out the battery holder.
2 Remove the old battery from the battery
holder then insert a new battery so that “+”
is facing upward.
3 Reinsert the battery holder into the remote
control.
18GB
To set the network standby
mode
To set the standby mode
SA-NS410
SA-NS410
1 Set the NETWORK STANDBY/
STANDBY switch to NETWORK
STANDBY.
2 Press the ?/1 (ON/Standby) button.
The ?/1 (ON/Standby) indicator lights up in
amber.
Note
Keep this unit in the network standby mode so it can
be controlled from a controller on the network even
when you are not currently operating this unit.
Tips
• The NETWORK STANDBY/STANDBY switch
is set to STANDBY in the factory default settings.
• The unit can be controlled from the controller on
your network, etc., when the unit is in the network
standby mode. The unit turns on automatically
when the controller delivers audio content to this
unit.
Getting Started
SA-NS310
SA-NS310
1 Set the NETWORK STANDBY/
STANDBY switch to STANDBY.
2 Press the ?/1 (ON/Standby) button.
The ?/1 (ON/Standby) indicator lights up in
red.
Note
You cannot operate this unit via a home network
when the unit is in the standby mode. Set the unit to
the network standby mode when you want to operate
the unit via a home network.
To resume power from the
network standby mode or the
standby mode
Press the ?/1 (ON/Standby) button.
The ?/1 (ON/Standby) indicator lights up in
green and the illumination indicator lights up.
To turn the unit off
Disconnect the AC power cord when you need
to turn the unit off, such as when you not use it
for a long time.
19GB
Network Connections
How to Connect Your
Network
Set up the network after checking your
network environment. Refer to the following
descriptions.
For details, refer to the following website:
http://www.sony.net/sans
Setting Up for a Wireless
Network
Select the suitable method and start to make
the network settings.
• Option 1: Method for using a supplied CDROM and Windows PC (page 20)
• Option 2: Method for using an application
for smartphones or Tablets (Android device/
iPhone/iPod touch/iPad) (page 21)
• Option 3: Manual setting method using an
Access Point Scan (for PC/Mac) (page 22)
• Option 4: Method for using a WPS push
button at the access point supporting WPS
(page 23)
Setting Up for a Wireless
Network
Note
When setting up a wireless network, SSID
(Wireless Network Name) and Security Key
(WEP or WPA key) may be required. Security
key (or network key) is an encryption key used
to limit the devices with which
communication can occur. It is used to provide
higher security for devices communicating via
a wireless LAN router/access point.
Option 1: Method for using a
supplied CD-ROM and Windows
PC
Note
Make sure your PC is wirelessly connected to a
LAN.
1
SSID (Wireless Network Name)
Setting Up for a Wired Network
Security Key (WEP or WPA key)
• Option 5: DHCP method (page 24)
Tip
About connecting the fixed IP address and
setting of the proxy server, display the Setting
Screen on a browser and set these referring to
”Option 3:Manual setting method using an
Access Point Scan (for PC/Mac)” (page 22).
When a problem occurs while
you are making the network
settings
Press ALL RESET button on the bottom of the
unit with a pointed object (such as a small pin)
(page 12 for SA-NS410/page 15 for SANS310).
20GB
Have your wireless network
name (SSID) and Security Key
(if applicable) available for
reference.
Refer to the operating instructions of the
wireless LAN router/access point.
2
Connect the AC adaptor to the
unit.
Check that the ?/1 (ON/Standby)
indicator changes from flashing in green
to lit in green.
3
Load the supplied CD-ROM into
the CD-ROM drive of your PC.
SSID (Wireless Network Name)
CD-ROM
Security Key (WEP or WPA key)
If the program does not start
automatically, double-click on
“NS_Setup.exe” on the CD-ROM.
4
Refer to the operating instructions of the
wireless LAN router/access point.
2
Perform setup, following step 1
to 4 of the on-screen
instructions.
Turn the unit on.
Check that the ?/1 (ON/Standby)
indicator changes from flashing in green
to lit in green.
• If you have set this already with any of
“Option 1” to “Option 4,” setup may not be
performed completely. Be sure to perform
all-reset for the unit. Press and hold the ALL
RESET button until all indicators light
(page 12 for SA-NS410/page 15 for SANS310).
• Do not connect the network (LAN) cable.
3
When setup is completed, press the “Play
test sound” button to confirm operation of
the speaker by playing the test sound.
Option 2: Method for using an
application for smartphones or
Tablets (Android device/iPhone/
iPod touch/iPad)
Notes
• Before starting this procedure, be aware that your
Wi-Fi network will not be protected until the
setting is complete. After the setting is complete,
your Wi-Fi network will be protected again when
you set wireless LAN security.
• The following procedure must be completed within
30 minutes. If you cannot complete it, turn off the
unit and start over from step 1.
1
Have your wireless network
name (SSID) and Security Key
(if applicable) available for
reference.
Download the “NS Setup”
application and launch it.
You can download the free application
from “Google Play” for Android devices
or “App Store” for iPhone/iPod touch/
iPad on the website.
You can search the application easily if
you type “NS Setup” into the search
screen.
When setting up with an iPhone/
iPod touch/iPad
Go to [Settings] - [Wi-Fi] and select
“Sony_Wireless_Audio_Setup”.
If “Sony_Wireless_Audio_Setup” does
not appear, wait until the speaker finishes
turning on.
21GB
Network Connections
Notes
4
For Mac OS X
Turn on Mac.
Click
icon on the top of the screen.
Turn on the Wi-Fi or AirPort. Then select
[Open Network Preferences...].
Select [Sony_Wireless_Audio_Setup]
from the network list.
Perform setup, following the
on-screen instructions.
When setup is completed, press the “Play
test sound” button to confirm operation of
the speaker by playing the test sound.
Option 3: Manual setting
method using an Access Point
Scan (for PC/Mac)
For Windows 7
Turn on PC.
Click
icon on the bottom of the
screen.
Select [Sony_Wireless_Audio_Setup]
from the network list.
Note
Before starting this procedure, be aware that your
Wi-Fi network will not be protected until the setting
is complete. After the setting is complete, your
Wi-Fi network will be protected again when you set
a wireless LAN security.
1
Have your wireless network
name (SSID) and Security Key
(if applicable) available for
reference.
SSID (Wireless Network Name)
Security Key (WEP or WPA key)
Refer to the operating instructions of the
wireless LAN router/access point.
2
3
Turn the unit on.
4
Check that the ?/1 (ON/
Standby) indicator changes
from flashing in green to lit in
green.
5
Connect the unit and a Mac or
PC.
22GB
Press and hold the ALL RESET
button on the bottom of the unit
with a thin object such as a
small pin until the ?/1 indicator
starts flashing.
For Windows Vista
Turn on PC.
Click
icon on the bottom of the
screen.
Click [Connect to a network].
Select [Sony_Wireless_Audio_Setup]
from the network list.
6
Access the [Sony Network
Device Setting] screen.
For Mac
Start Safari and select [Bonjour] under
[Bookmarks], then select [SA-NS410] or
[SA-NS310].
For PC
Start the browser and input either of the
following URLs into the browser’s
address bar.
7
Select the desired language
when the [Language Setup]
screen appears.
Note
This procedure needs to be completed within 30
minutes. If you cannot complete, start over from
step 3.
Option 4: Method for using a
WPS push button at the access
point supporting WPS
1
Disconnect the network (LAN) cable
while the AC power is disconnected if the
network (LAN) cable is connected.
Select [Network Settings] from
the menu.
2
Turn the unit on.
You can operate this unit when the ?/1
(ON/Standby) indicator lights up in green
and the illumination indicator lights up. It
may take a while.
Network Settings
9
Note
Select the SSID of the wireless
LAN router/access point, then
input the Security Key (if
applicable).
Make sure the AUDIO IN indicator is not lit.
3
Press the WPS button on the
access point.
WPS button*
* The position and the shape of the WPS button
are different depending on the model of the
access point.
SSID
10 Select [Apply].
11 Click [OK] in the displayed
Tip
Refer to the operating instructions of your
wireless LAN router/access point for details on
the WPS button.
window.
The unit restarts automatically, then the
LINK indicator lights up green when the
connection is established.
12 Reconnect the Mac or PC to
4
Press the WPS button on the
unit for three seconds.
The LINK indicator lights up in green
when the connection is made.
your network.
23GB
Network Connections
8
Check whether the network
(LAN) cable (not supplied) is
disconnected.
Setting Up Wired
Networks
Option 5: DHCP method
Usually, the DHCP setting is set to ON when
you connect your computer to the network.
Try the following method if you are using a
wired network.
Set the DHCP setting of your computer to ON
in advance.
1
Check whether your computer
and router are turned on.
2
Connect the unit and the router
using a network (LAN) cable
(not supplied).
3
Connect the router and your
computer using a second
network (LAN) cable (not
supplied).
Network (LAN) cable
(not supplied)
Network
(LAN) cable
(not supplied)
4
Turn the unit on.
The LINK indicator lights up in amber
when the connection is made.
24GB
Listening to Audio Content Over
Your Home Network
Using DLNA (Digital
Living Network Alliance)
Listening to audio content on a
computer with Windows 7
Windows 7 supports DLNA1.5. Windows 7
can be used as both server and controller. You
can listen to audio content on the server easily
using the [Play To] function of Windows 7.
Control &
Deliver
Device with Network Audio Remote*
or DLNA controller
Control
DLNA controller/Server
(Windows 7-based
computer)
Network controlled
player (this unit)
Access
Note
Deliver
Server
Network controlled
player (this unit)
* Sony provides the “Network Audio
Remote” application for free.
For details, refer to the following website:
http://www.sony.net/sans
The unit can play audio content stored on the
server in MP3, Linear PCM, WMA and AAC*
formats. Audio content with DRM (Digital
Rights Management) copyright protection
cannot be played on this unit.
* The unit can play AAC files with the extension of
“.m4a,” “.mp4,” or “.3gp” only.
Notes
• Generally, it may take a while to recognize each
DLNA-compliant device currently used when you
enjoy audio content via a home network.
• This unit cannot playback files in WMA format
with DRM copyright protection. If a WMA file
cannot be played back on this unit, check the
The items displayed on the computer may be
different from the ones shown in this section,
depending on the version of the operating system or
the computer environment. For details, refer to the
help of your operating system.
Setting up a computer with
Windows 7
1 Go to [Start] - [Control Panel] and select
[View network status and tasks] under
[Network and Internet].
The [Network and Sharing Center] window
appears.
Tip
If the desired item does not appear in the display,
try to change the display type of the Control
Panel.
25GB
Listening to Audio Content Over Your Home Network
You can play back audio content on DLNAcompliant servers such as your computer, or
network audio, etc., on this unit by controlling
the server using “Network Audio Remote”
application. A DLNA-compliant controller
device (a remote control device, etc.) is needed
for the operation.
You can use Windows 7 as both server and
controller.
property of that file on your computer, and see
whether the file is DRM-copyrighted.
Open a folder or a volume where the WMA file is
stored, and right-click the file to display the
[Property] window. When there is the [Licence]
tab, the file is DRM-copyrighted and cannot be
played back on this unit.
• You may not be able to play back some content
with DLNA CERTIFIED products.
2 Select [Public network] under [View your
active networks]. If the display shows other
than [Public network], go to step 5.
6 Select [Choose media streaming options...]
from [Media streaming].
The [Set Network Location] window appears.
3 Select [Home network] or [Work network]
7 If [Media streaming is not turned on]
according to the environment in which the
speaker is used.
4 Follow the instructions that appear on the
display according to the environment in
which the speaker is used.
When the change is completed, confirm that
the item under [View your active networks]
has been changed to [Home network] or
[Work network] in the [Network and
Sharing Center] window.
5 Select [Change advanced sharing settings].
appears in the Media streaming options
window, select [Turn on media streaming].
8 Select [Allow All].
The [Allow All Media Devices] window
opens. If all the devices in the local network
are [Allowed] to access your network, select
[OK] and close the window.
9 Select [Allow all computers and media
devices].
10Select [OK] to close the window.
Listening to audio content
stored on a computer with
Windows 7
1 Start [Windows Media Player] of
Windows 7.
2 Turn on media streaming.
3 Select the desired audio content, then click
the right mouse button.
26GB
4 Select [Play To] from the menu.
depending on the version of the operating system or
the computer environment. For details, refer to the
help of your operating system.
Setting up a computer with
Windows Vista/ Windows XP
1 Go to [Start] - [All Programs] and select
The device list appears.
5 Select [SA-NS410] or [SA-NS310].
[Windows Media Player].
Windows Media Player 11 starts up.
2 Select [Media Sharing...] from the [Library]
menu.
If you are using Windows XP, go to step 8.
3 When
is displayed, select
[Networking...].
The audio content is played back from this
speaker.
Listening to audio content on a
computer with Windows Vista/
Windows XP
You need to set up Windows Media Player 11
to listen to the music using the Windows Vista/
Windows XP* as a server.
*
Windows Media Player 11 is not manufacturerinstalled on Windows XP. Access the Microsoft
website, download the installer, and then install
Windows Media Player 11 on your computer.
Update the software version of your computer to
XP Service Pack 2 or later, then install Windows
Media Player 11. You cannot install Windows
Media Player 11 on versions of XP prior to Service
Pack 2.
The [Set Network Location] window
appears.
Note
The items displayed on the computer may be
different from the ones shown in this section,
27GB
Listening to Audio Content Over Your Home Network
The [Network and Sharing Center] window
appears.
4 Select [Customize].
5 Add a check next to [Private] and select
[Next].
Note
Uncheck this item after you confirm that the unit can
connect to the computer and play audio data on the
computer.
Listening to audio content
stored on a computer with
Windows Vista/ Windows XP
You can play back audio content, using the
DLNA controller (page 25).
6 Confirm that the [Location type] has been
changed to [Private] and select [Close].
7 Confirm that [(Private network)] is
displayed in the [Network and Sharing
Center] window and close the window.
8 If a check is not added next to [Share my
media] in the [Media Sharing] window that
is displayed in step 2, add a check next to
[Share my media], then select [OK].
A list of connectable devices is displayed.
9 Select [Settings...] that appears beside
[Share my media to:].
10Add a check next to [Allow new devices
and computers automatically] and select
[OK].
28GB
Using Internet music streaming
(Music Service)
Using Internet music
streaming
You can listen to various Internet music
streaming offered on the Internet, using
“Network Audio Remote” without a PC.
Control
Deliver
Internet
Notes
• Before using Internet music streaming, check the
following:
– Check that all devices are connected to your
home network and set up correctly.
– Check that the unit is turned on or in network
standby mode.
– Check that the unit and the controller are allowed
to access the server.
– Check that the unit and the server have been
recognized and registered with the controller.
• You may have to register your system depending
on the service provider. For details on registration,
visit the customer support site of the service
provider. For details, refer to the following
website:
http://www.sony.net/sans
• If you need the latest support information on
Internet music streaming and Registration code,
refer to the following website:
http://www.sony.net/sans
1
Download the application
“Network Audio Remote” and
launch it.
You can download the free application
from “Google Play” for an Android
device or “App Store” for iPhone/iPod
touch/iPad on the website.
You can search the application easily if
you enter “Network Audio Remote” into
the search screen.
2
Select the desired Internet
music streaming.
e.g. Music Unlimited
[Music Services] - [Music Unlimited] [Genre]
29GB
Using Internet music streaming (Music Service)
Access
Preparing your mobile device
instead of the remote control
Enjoying Internet music
streaming
3
A list of service providers to which the
unit can be connected appears.
Tip
The screens used in the following section are of the
iPad. The screens of Android devices or iPhone/iPod
touch differ.
1
Tap/click on the
icon on the
screen of the Android device or
iPhone/iPod touch/iPad.
2
Select your unit (SA-NS310
xxxxxx or SA-NS410 xxxxxx)
from the speaker list.
Select the “Music Service”
from the Browse Music list.
4
Select the service provider you
want.
5
Select the desired playable
content and start playback.
Tip
If playback does not start, perform the process again
from step 1.
To confirm/edit the device name
You can confirm and edit the device name of
this unit, using the setting screen on the
browser.
See “Device Details screen” (page 37) for
details.
To control Internet music
streaming with the unit or
remote control
You can use the VOL (VOLUME) +/– and
MUTING buttons. Operation from the unit
and the remote control is active only when the
unit is selected as the device for output.
Browse Music list
30GB
Tips
• Very loud sound may output from this unit when
you set the volume too high using an Android
device or iPhone/iPod touch/iPad.
• For details on the use of the Android OS or iOS,
refer to Help of each OS.
• The volume level of a the Android device or
iPhone/iPod touch/iPad may not be able to be
linked with the volume level of this unit.
• For details on the use of “Network Audio
Remote,” tap/click on the Help icon or Option icon
of it.
Using Internet music streaming (Music Service)
31GB
1
Launch the music application
of your iPhone, iPod touch,
iPad, or iTunes.
2
Tap/click on the
icon at
bottom right of the iPhone, iPod
touch or iPad screen or iTunes
window.
Using AirPlay
Using AirPlay
You can play audio from iPhone, iPod touch or
iPad, and Mac or PC with iTunes.
iPhone, iPod touch or iPad
Control & stream
Compatible iPhone/iPod touch/
iPad models
iPhone 4S, iPhone 4, iPhone 3GS, iPod touch
(3rd or 4th generation), iPad, iPad2 with iOS
4.3.3 or later, and Mac or PC with iTunes
10.2.2 or later.
Notes
• See “Compatible iPhone/iPod touch/iPad models”
on this page for details on the supported versions of
iOS or iTunes.
• Update iOS or iTunes to the latest version before
using with this unit.
• Refer to the operating manual of your device for
details on operating iPhone, iPod touch, iPad,
iTunes or AirPlay.
• You cannot use this unit as a PARTY host during
the AirPlay playback.
iTunes
3
Select “SA-NS410” or “SANS310” on the AirPlay menu of
iTunes or your iPhone, iPod
touch or iPad.
iPhone, iPod touch or iPad
32GB
iTunes
4
Start playing back audio
content on an iPhone, iPod
touch, iPad or iTunes.
Tip
If the playback does not start, perform the process
again from step 1.
To confirm/edit the device name
Using AirPlay
You can confirm and edit the device name of
this unit using the setting screen on the
browser.
See “Device Details screen” (page 37) for
details.
To control AirPlay playback
You can use the VOL (VOLUME) +/– and
MUTING buttons. Operation from the unit
and the remote control is active only when the
unit is selected as the device for output.
For using iTunes, set it to accept control from
the remote control if you want to use the
remote control to operate iTunes.
Tips
• Very loud sound may output from this unit when
you set the volume too high using iPhone, iPod
touch, iPad or iTunes.
• For details on the use of iTunes, refer to Help of
iTunes.
• The volume level of iPhone, iPod touch, iPad or
iTunes may not be able to be linked with the
volume level of this unit.
33GB
3
Using Music Throw
Using Music Throw on a
Sony Tablet
Select “SA-NS410” or “SANS310” on the Music Throw
menu of Sony Tablet.
Sony Tablet
You can play audio from a Sony Tablet.
Control & Stream
Notes
• Update the Android OS to the latest version before
using it with this unit.
• Refer to the operating manual of your Sony Tablet
for details.
• You cannot use this unit as a PARTY host during
the Music Throw playback.
• Music player will be available on Xperia
smartphones from Sony Mobile Communications
in autumn of 2012. For details about upgrading,
check the Sony Mobile Communications website.
1
Launch the “Music player”
application on the Sony Tablet.
4
Start playing back audio
content on the Sony Tablet.
Tip
If playback does not start, perform the process again
from step 1.
To confirm/edit the device name
You can confirm and edit the device name of
this unit, using the setting screen on the
browser.
See “Device Details screen” (page 37) for
details.
To control Music Throw
playback
2
Tap/click on the
icon at top
center of the Sony Tablet.
You can use the VOL (VOLUME) +/– and
MUTING buttons. Operation from the unit
and the remote control is active only when the
unit is selected as the device for output.
Tips
• Very loud sound may output from this unit when
you set the volume too high using a Sony Tablet.
• For details on the use of the Android OS, refer to
Help of Android OS.
• The volume level of a Sony Tablet may not be able
to be linked with the volume level of this unit.
34GB
Others
Using the PARTY
STREAMING
You can play back audio content that is being
played back on this unit or on another device
that has a PARTY STREAMING function at
the same time, via your home network.
While using the PARTY STREAMING
function, the device that starts a PARTY and
streams the audio content is called the
“PARTY host,” and the device that joins a
PARTY and plays the audio content streamed
from the PARTY host is called a “PARTY
guest.”
Starting a PARTY
You can start a PARTY so that other devices
which support the PARTY STREAMING
function can play the same music even though
they are in different rooms.
1
Make sure the PARTY guest
devices are turned on and are
in a status which allows them to
join a PARTY.
2
Play back audio content using
the AUDIO IN terminal or audio
content stored on the server on
your network on this unit.
3
Press and hold PARTY for a few
seconds.
The unit starts PARTY STREAMING
and the PARTY STREAMING indicator
lights up in green.
To close a PARTY
Notes on using the PARTY
STREAMING
Notes
Depending on your device or environment, sound
may skip or the unit cannot connect to the network.
In this case, try following:
• Perform firmware updates for your router to the
latest version. For details on the firmware updates,
refer to the operating manual of your device.
• Perform firmware updates for your speaker to the
latest version (page 36).
• If you are connecting to the network using wireless
connection, change to using wired connection.
• For more detail information, refer to the following
web site:
http://www.sony.net/sans
Press and hold PARTY for a few seconds.
The PARTY STREAMING indicator goes off.
• An error has occurred when the PARTY
STREAMING indicator lights up in red. Perform
the process from step 1 again.
• You cannot start a PARTY while you are currently
participating in a PARTY.
• If the PARTY button is pressed on another device
that complies with the PARTY STREAMING
function while the unit is playing a track, the unit
will start a PARTY as a PARTY host and the other
device will join a PARTY as a PARTY guest.
Joining a PARTY
The unit can join a PARTY which has been
started by another device so that you can enjoy
the same audio content as that being played in
a different room.
35GB
Others
You can enjoy the PARTY STREAMING
function with other devices that have this
PARTY STREAMING logo.
When another device (PARTY host)
is having a PARTY, press PARTY.
The unit joins the PARTY as a PARTY guest
and the PARTY STREAMING indicator
lights up in amber.
To leave a PARTY
Press PARTY.
The PARTY STREAMING indicator goes off.
Notes
• An error has occurred when the PARTY
STREAMING indicator lights up in red. Perform
the process from step 1 again.
• The PARTY STREAMING indicator lights up in
amber when other devices utilizing the PARTY
STREAMING function invite this unit to a
PARTY. When you want to leave that PARTY,
press PARTY.
• You cannot join a PARTY in the following cases:
– you have a PARTY on this unit
– you have already joined in another PARTY
• If you press PARTY when no PARTY is being
held, but a device that complies with the PARTY
STREAMING function is playing, the device will
be the PARTY host and the unit will join the
PARTY as a PARTY guest.
Updating software
When a new update is available, the UPDATE
indicator lights up in green while the unit is
connected to the Internet.
Check the following customer support website
about the update:
http://www.sony.net/sans
Notes
• Perform the following operations after confirm the
message and also read and agree the “END-USER
LICENSE AGREEMENT FOR SONY
SOFTWARE” (page 49).
• Make sure you do not attempt any of the following
operations while the update is in progress.
– Turning the unit off
– Connecting or disconnecting the network (LAN)
cable (not supplied)
– Disconnecting the AC adaptor
• About connecting the fixed IP address and setting
of the proxy server, display the Setting Screen on a
browser and set these referring to “Option
3:Manual setting method using an Access Point
Scan (for PC/Mac)” (page 22).
1
Tip
To use the PARTY STREAMING
function with a Network Audio
Remote
You can use a Network Audio Remote that
supports the PARTY STREAMING function
to use the unit to start a PARTY that is being
held by other devices.
Quit all operations before
updating.
If you do not quit those, the unit will quit or
stop all operations automatically.
2
Press and hold the UPDATE
button on the side of SA-NS410
or the bottom of SA-NS310 until
the illumination is turned off.
The update starts.
The UPDATE indicator flashes during
the update.
36GB
SA-NS410
Setting Screen on the
Browser
To display the [Setting Screen] in your
browser, refer to Option 2 “Method for using
an application for smartphones or Tablets
(Android device/ iPhone/iPod touch/iPad)”
(page 21) or Option 3 “Manual setting method
using an Access Point Scan (for PC/Mac)”
(page 22).
SA-NS310
Using the setting screen on the
browser
You can make the various settings of this unit
using the setting screen on the browser.
bottom
Device Details screen
Notes
You can check the information on this unit.
Others
• It takes for a while to finish updating.
• You cannot operate the unit until updating has
completed.
• It may take several minutes to update the software
of the unit. The time required depends on the size
of the update content and type of Internet
connection you are using.
37GB
Network Settings screen
2
You can make the network settings using this
screen.
Click [Add/Remove Windows
Components].
The Windows Components Wizard
appears.
Starting the browser with
Windows XP
3
Click [Networking Services] t
[Details...].
4
Put a check the check box
beside [UPnP User Interface],
then click [OK].
You have to install the UPnP service for
browsing.
Note
The items displayed on the computer may be
different from the ones shown in this section,
depending on the version of the operating system or
the computer environment. For details, refer to the
help of your operating system.
1
38GB
Click [Control Panel] t [Add or
Remove Programs].
5
6
Click [Next].
The [Completing the Windows
Components Wizard] window appears.
Specifications
Click [Finish].
AUDIO POWER
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
[SA-NS410]
Tweeter L+R
With 5 ohms loads, both channels driven, from
500 - 20 kHz; rated 10 watts per channels
minimum RMS power, with no more than 1 %
total harmonic distortion from 100 milliwatts
to rated output.
[SA-NS310]
With 4 ohms loads, driven from 80 - 20 kHz;
rated 6 watts minimum RMS power, with no
more than 1 % total harmonic distortion from
100 milliwatts to rated output.
Power Output (reference):
[SA-NS310]
10 W (4 ohms, 1 kHz, THD 10%)
Wireless LAN section
Compatible standards:
IEEE 802.11 b/g
(WEP 64 bit, WEP 128 bit,
WPA/WPA2-PSK (AES),
WPA/WPA2-PSK (TKIP))
Frequency and Channel:
2.4 GHz
USA, Canada: CH 1 - CH 11
Others: CH 1 - CH 13
Inputs/Outputs
Speakers
[SA-NS410]
39GB
Others
[SA-NS410]
Tweeter L+R 15 W + 15 W (5 ohms, 1 kHz, THD
10%)
Woofer 15 W (6 ohms, 100 Hz, THD 10%)
Tweeter: Approx. 30 mm (1 3/16 in) diameter
×4
Woofer: Approx. 110 mm (4 3/8 in) diameter
×1
[SA-NS310]
Approx. 50 mm (2 in) diameter × 1
AUDIO IN jack:
Stereo mini jack
Voltage: 1.0 V
Network port:
Mass
[SA-NS410]
Approx. 3.8 kg (8.4 lb)
[SA-NS310]
Approx. 1.1 kg (2.4 lb)
Supplied accessories:
[SA-NS410]
See page 17.
[SA-NS310]
See page 17.
10BASE-T/100BASE-TX (Auto Polarity)
General
Power requirements:
[SA-NS410]
AC adaptor
Input: 120 V-240 V AC, 50/60 Hz
Output: DC 18 V 2.6 A
[SA-NS310]
AC adaptor
Input: 100 V-240 V AC, 50/60 Hz
Output: DC 13 V 2 A
Power consumption:
[SA-NS410]
When the unit is on: DC 18 V, 0.9 A
When the unit in standby mode: 0.5 W or below
When the unit in network standby mode:
3.5 W or below
[SA-NS310]
When the unit is on: DC 13 V, 0.4 A
When the unit in standby mode: 0.5 W or below
When the unit in network standby mode:
3.5 W or below
Dimensions (w/h/d) (including
projecting parts and controls):
[SA-NS410]
Approx. 240 mm × 273 mm × 185 mm
(Approx. 9 1/2 in × 10 3/4 in × 7 3/8 in)
[SA-NS310]
Approx. 162 mm × 136 mm × 162 mm
(Approx. 6 3/8 in × 5 3/8 in × 6 3/8 in)
40GB
Design and specifications are subject to
change without notice.
On placement
Precautions
On safety
• Before operating the system, be sure that the
operating voltage of the system is identical
with that of your local power supply.
Where purchased Operating voltage
North America
120 V AC, 60 Hz
All other regions
100 V-240 V AC, 50/
60 Hz (SA-NS310)
120 V-240 V AC, 50/
60 Hz (SA-NS410)
• Use only the supplied AC adaptor and AC
power cord.
• When carrying the unit, be sure to hold it by
the bottom of the unit. Do not hold it by the
cloth, as the unit to may slip out.
• Do not set the unit in an inclined position.
• Do not leave the unit in a location near heat
sources, or in a place subject to direct
sunlight, excessive dust, moisture, rain or
mechanical shock.
• Do not place metal objects in front of the
front panel. They may limit reception of
radio waves.
• Do not place the system in a place where
medical equipment is in use. It may cause a
malfunction of medical equipment.
• If you use a pacemaker or other medical
device, consult your physician or the
manufacturer of your medical device before
using the wireless LAN function.
On cleaning
• Wipe the unit using a soft cloth such as the
cloths used for cleaning eye glasses, etc.
• Do not use alcohol, benzine, or thinner to
clean the cabinet.
On operation
• Do not open the cabinet. Refer servicing to
qualified personnel only.
• Should any solid object or liquid fall into the
system, have the system checked by
qualified personnel before operating it any
further.
• This system is not magnetically shielded, do
not leave recorded tapes, watches, personal
credit cards, or floppy disks with magnetic
coding in front of the system for an extended
period of time.
• Do not put anything on top of the unit.
Others
If the TV picture or monitor
display is magnetically
distorted
This speaker system is not magnetically
shielded, and the picture on nearby TV sets
may become magnetically distorted. In this
situation, turn off the TV, wait 15 to 30
minutes, and turn it back on. If there is no
improvement, move the speakers far away
from the TV.
41GB
Troubleshooting
Troubleshooting
If a problem occurs while operating the unit,
follow the steps described below before
consulting your nearest Sony dealer. If an error
message appears, it is recommended that you
make a note of its contents for reference.
1
Check to see if the problem is
listed in this “Troubleshooting”
section.
2
Check the following customer
support site.
http://www.sony.net/sans
You will find the latest support
information and a FAQ at this website.
3
If, after steps 1 and 2, you still
cannot solve the problem,
consult your nearest Sony
dealer.
If the problem persists after doing all of
the above, consult your nearest Sony
dealer.
When bringing the product in for repairs,
be sure to bring in the entire system (main
unit, remote control, AC adaptor, and AC
power cord).
This product is a system product, and so
the entire system is needed to determine
the section requiring repair.
Power
The unit does not turn on.
• Make sure the AC adaptor and AC power
cord are connected correctly.
• Be sure to press the ?/1 (ON/Standby)
button to set the unit to on.
• Press the ?/1 (ON/Standby) button to set
standby mode then press to set it back to
on.
The network does not work after you
press the ?/1 (ON/Standby) button to
set the unit to on.
• It takes about 40 seconds for the unit to
turn on.
The unit remains warm after the power
is turned off.
• When the unit is in the network standby
mode, some parts of the internal system
remain active. Press the ?/1 (ON/Standby)
button after setting the NETWORK
STANDBY/STANDBY switch to
STANDBY to minimize the power
consumption. However, the unit cannot be
operated using a controller on your
network with this setting.
The unit turns on and starts playback
automatically.
• The unit can be controlled by a controller
on your network. If the unit receives an
order to play the audio content on the
server while it is in network standby mode,
it turns on and starts playback
automatically. To enter network standby
mode again, press the ?/1 (ON/Standby)
button on the remote control. To prevent
the unit from automatically turning on, set
the NETWORK STANDBY/STANDBY
switch to STANDBY.
The unit turns off automatically.
• The unit enters the selected standby mode
after being idle for 30 minutes.
42GB
Sound output
There is no sound.
• Press the VOL (VOLUME) + button to
turn up the volume. The unit may have
been set to silence the sound by a
controller on your network. If the sound is
output for a moment and then is silenced
again, the unit may have received a
command to silence the sound. Confirm
the setting of the controller and release
deleting the sound.
• When the PARTY STREAMING
indicator lights in amber, confirm the
audio format of the audio content that is
being played by the PARTY host. The unit
stops playback when the PARTY host
attempts to play audio content of an audio
format that cannot be played on the unit.
• Sound is not output when the unit is muted
by your having pressed the MUTING
button. The illumination indicator on the
front of the unit flashes in blue during
muting. In this case, press MUTING or
VOL +/– button on the remote control
when you wish to release muting.
There is severe humming, noise, or
sound distortion from the speakers.
• Connect the unit and other devices
correctly (page 12 for SA-NS410/page 14
for SA-NS310).
The unit cannot connect to the
network. (The unit cannot be found or
recognized by other devices that are on
the home network.)
• If you use the unit in a network
environment without a router, it may take
about a minute for the unit to obtain its IP
address after you turn on the power.
• The IP address may be in use by another
device when you use a fixed IP address.
Use a different IP address in such a case.
The unit cannot connect to the network
via a wireless LAN connection.
• Make sure a network (LAN) cable is not
connected to the unit. The unit
automatically tries to connect to the
network over a wired LAN connection
when a network (LAN) cable is connected
to the unit.
• Confirm that the access point (wireless
LAN router) setting is correct. When SSID
of the access point is hidden, set the SSID
stealth mode switch for the access point to
OFF. For details on the access point
setting, refer to the operating instructions
of the access point.
The unit cannot be connected via the
wireless LAN connection using the
WPS.
• You cannot connect to a network using
WPS when your access point is set to
WEP. Set up your network after searching
the access point using the access point
scan.
The wireless LAN transfer speed
becomes noticeably slow.
• With some IEEE802.11n-compatible
wireless LAN routers/access points, the
wireless LAN transfer speed is decreased
when “WEP” or “WPA/WPA2-PSK
(TKIP)” is selected for the security
method.
Configurations of encryption (security)
43GB
Troubleshooting
The sound skips.
• The sound may skip, depending on the
network environment, etc., when you use a
wireless network. In this case, try
changing the security method to “WPA/
WPA2-PSK (AES).” This may improve
the transfer speed and streaming playback.
• The servers are overloaded. Close all other
applications you are currently using.
• Perform firmware updates for your access
point (wireless LAN router) to the latest
version.
Network
vary depending on the model; please refer
to the operating instructions supplied with
your router/access point.
Browser
The browser screen does not appear.
• Check the setup of the firewall of the
security software. Refer to the customer
support website (page 42) for details.
• Check the proxy setting of the browser.
This unit does not support proxies. Change
the browser setting to one connecting this
unit without a proxy.
Home Network
The unit cannot be found from a
controller. (The controller cannot
browse the unit.)
• See “Browser” – “The browser screen
does not appear. ” (page 44)
• Make sure the LINK indicator lights in
green or amber. If the LINK indicator goes
dark, flashes, or lights in red, see
“Network” – “The unit cannot connect to
the network. (The unit cannot be found or
recognized by other devices that are on the
home network.) ” (page 43).
• Make sure the controller is connected to
your home network.
Audio content has started
automatically.
• The unit may be under the control of
another device. If you want to reject these
requests, set the NETWORK STANDBY/
STANDBY switch to STANDBY.
The sound skips.
• See “Sound output” – “The sound skips.”
(page 43).
44GB
This unit cannot play back with this
error indicated (illumination indicator
[white] continues flashing quickly).
• Make sure that the audio content is not
corrupted and has not been deleted from
the server. Refer to the operating
instructions of the server.
• The server is trying to play back an
unsupported audio format on this unit.
Check the format information, using the
server.
• Deactivate the multicast control of your
wireless LAN router/access point if it is
activated. Refer to the operating manual of
your wireless LAN router/access point for
details.
This unit cannot play back with this
indicated (illumination indicator [white]
continues flashing).
• It may take several minutes before sound is
output. Wait until the indicator stops
flashing.
• The server may not permit access from this
unit. Change the settings of the server to
permit access from this unit. Refer to the
operating instructions of the server.
The pause function does not work.
• This unit does not have a pause function.
AirPlay
The unit cannot be found from an
iPhone, iPod touch, or iPad.
• See “Browser” – “The browser screen
does not appear. ” (page 44).
• Make sure the LINK indicator lights in
green or amber. If the LINK indicator goes
dark, flashes, or lights in red, see
“Network” – “The unit cannot connect to
the network. (The unit cannot be found or
recognized by other devices that are on the
home network.) ” (page 43).
• Make sure an iOS device or a PC with
iTunes is connected to your home network.
• Update iOS or iTunes to the latest version
before using it with this unit (page 32).
Audio content automatically started.
• See “Home Network” – “Audio content
has started automatically. ” (page 44).
The sound skips.
• See “Sound output” – “The sound skips.”
(page 43).
This unit cannot be operated.
• Update the software version of the iPhone,
iPod touch, or iPad to the latest version
(page 32).
• Make sure another device is not streaming
to the AirPlay compatible device at the
same time.
PARTY STREAMING
• See “Home Network” (page 44) if the
problem does not apply to one of the
following cases:
During a PARTY
The sound skips.
• See “Sound output” – “The sound skips.”
(page 43).
The wireless LAN transfer speed
becomes noticeably slow.
• See “The wireless LAN transfer speed
becomes noticeably slow.” (page 43).
Using this unit as a PARTY host
This unit cannot start a PARTY.
• Make sure the LINK indicator lights in
green or amber. If the LINK indicator goes
dark, flashes, or lights in red, see
“Network” – “The unit cannot connect to
the network. (The unit cannot be found or
recognized by other devices that are on the
home network.) ” (page 43)
This unit cannot leave the PARTY.
• You cannot leave the PARTY while using
this unit as a PARTY host.
Another device cannot join the PARTY
that is being held on this unit.
• The number of PARTY guest exceeds the
maximum number when the PARTY
STREAMING indicator flashes in green
and red alternately. Remove one of the
PARTY guests.
45GB
Troubleshooting
This unit cannot join a PARTY.
• Make sure the LINK indicator lights in
green or amber. If the LINK indicator goes
dark, flashes, or lights up in red, see
“Network” – “The unit cannot connect to
the network. (The unit cannot be found or
recognized by other devices that are on the
home network.) ” (page 43).
• Make sure of the statuses of other PARTY
guests. The unit cannot join a PARTY if
other PARTY devices have all left the
PARTY. Play back via another PARTY
device when you join the PARTY as a
PARTY guest. If you want to start a
PARTY as a PARTY host, press and hold
the PARTY button for two seconds or
more.
• See “Home Network” – “This unit cannot
play back with this error indicated
(illumination indicator [white] continues
flashing quickly). ” (page 44).
The unit takes a few minutes to connect
to the PARTY host.
• Check the status of the PARTY
STREAMING indicator. The PARTY has
already closed if the PARTY
STREAMING indicator goes dark. This
unit is the PARTY host if the PARTY
STREAMING indicator lights in green.
Play back the audio content.
Internet music streaming (Music
Services)
You cannot connect the system to a
service.
• Make sure that the wireless LAN router/
access point is turned on.
• Check the LINK indicator to confirm the
network status. If the LINK indicator is
not lit in green or amber, make the wireless
network settings again (page 20).
• If the system is connected through a
wireless network, move the unit and the
wireless LAN router/access point closer to
each other and do the setup again.
• If your contract with your Internet
provider limits Internet connection to one
device at a time, this device will not be
able to access the Internet when another
device is already connected. Consult your
carrier or service provider.
• Relaunch the Network Audio Remote
application after turning your mobile
device (Android phone/Sony Tablet/
iPhone/iPod touch/iPad) off then back on.
The sound skips.
• The bandwidth of your wireless LAN may
be too low. Move the unit and the wireless
LAN router/access point closer to each
other, without any obstacles between.
Others
This unit does not work correctly.
• This unit is affected by static electricity,
etc. Reset this unit if the unit does not work
correctly. Disconnect and reconnect the
AC cord of the unit.
This unit does not operate if you press
the buttons of this unit or those of the
remote control.
• Buttons do not work during initializing or
startup.
46GB
• Buttons do not work while you are
updating the software.
• Buttons other than the ?/1 (ON/Standby)
button on the remote control do not work
in network standby mode.
The remote control does not work.
• There are inverter fluorescent lights near
the unit. Keep this unit away from inverter
fluorescent lights.
• Make sure the battery is installed correctly.
• Check the remaining battery level of the
remote control.
• Operate the remote control while aiming it
at PARTY button (the remote sensor) on
the unit.
The ?/1 (ON/Standby) indicator flashes
in red.
• The system is in protection mode.
Disconnect the AC cord of the unit then
reconnect it after a few seconds. Then turn
the unit on. If the symptom recurs, consult
your nearest Sony dealer.
The unit and AC adaptor are getting
hot.
• This is not a malfunction.
Indicator information
Indicator
White
Blue
Illumination
Lit:
– In Playback mode
– In selecting audio input
Flashing:
– During VOL buttons operation
– During starting-up
Cycle of flashing at 1 sec:
In preparation for playback
Cycle of flashing twice in 1 sec:
In pause mode
Cycle of flashing 4 times in 1 sec:
An error has occurred
– In Standby mode
Lit:
– During updating
In stopped Playback mode
Flashing:
During VOL buttons operation
Cycle of flashing at 1 sec:
During muting
Cycle of flashing twice in 1 sec:
During transition to Standby mode
NON
Flashing in white and blue alternately: During starting-up
Indicator
Green
Amber
?/1 (ON/
Standby)
Lit:
In operation
Flashing:
During starting-up
Lit:
Lit:
In network standby mode In standby mode
Flashing:
See “The ?/1 (ON/
Standby) indicator
flashes in red.”
(page 46)
Red
NON
PARTY
STREAMING
Lit:
Having a PARTY as
PARTY host
Cycle of flashing at 1 sec:
Preparation for having a
PARTY as PARTY host
Cycle of flashing 4 times
in 1 sec:
Closes the PARTY
Lit:
Joining a PARTY as
PARTY guest
Cycle of flashing at 1 sec:
Preparation for joining a
PARTY as PARTY guest
Cycle of flashing 4 times
in 1 sec:
Leaves the PARTY
Cycle of flashing 4
No PARTY
times in 1 sec for 2 sec
t goes dark:
An error has occurred
LINK
Lit:
During wireless connection
Cycle of flashing for 2 sec
and dark for 1 sec:
Begins wireless connection
Lit:
During wired connection
Cycle of being lit for 2
sec and dark for 1 sec:
Begins wired connection
Lit:
An error has occurred
(with the wireless LAN
setting/ not connected)
Cycle of flashing 4
times in 1 sec:
A wireless LAN WPS
error has occurred
UPDATE
Lit:
Updatable
Flashing:
During updating
–
No need for
Cycle of flashing 4
times in 1 sec for 4 sec updating
t goes off:
An updating error has
occurred
AUDIO IN
Lit:
In selecting audio input
–
–
AC adaptor is
not connected
In selecting
network input
47GB
Troubleshooting
A wireless
network
setting process
is not finished
Trademarks, etc.
• PARTY STREAMING and the PARTY
STREAMING logo are trademarks of Sony
Corporation.
• Microsoft, Windows, Windows Vista,
Windows 7™, Windows Media are trademarks or
registered trademarks of Microsoft Corporation in
the United States and/or other countries.
• This product is protected by certain intellectual
property rights of Microsoft Corporation. Use or
distribution of such technology outside of this
product is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary.
• AirPlay, the AirPlay logo, iPhone, iPod touch, and
iTunes are trademarks of Apple Inc., registered in
the U.S. and other countries. iPad is a trademark of
Apple Inc.
The Wi-Fi Logo is a certification mark of
•
the Wi-Fi Alliance.
• Wi-Fi®, Wi-Fi Protected Access® and Wi-Fi
Alliance® are registered marks of the Wi-Fi
Alliance.
• Wi-Fi CERTIFIED™, WPA™, WPA2™ and WiFi Protected Setup™ are marks of the Wi-Fi
Alliance.
• DLNA®, the DLNA Logo and DLNA
CERTIFIED™ are trademarks, service marks, or
certification marks of the Digital Living Network
Alliance.
• Windows Media is either a registered trademark or
trademark of Microsoft Corporation in the United
States and/or other countries.
This product is protected by certain intellectual
property rights of Microsoft Corporation.
Use or distribution of such technology outside of
this product is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary.
• MPEG Layer-3 audio coding technology and
patents licensed from Fraunhofer IIS and
Thomson.
WPA Supplicant
Copyright © 2003-2006, Jouni Malinen
<[email protected]> and contributors
All Rights Reserved.
Redistribution and use in source and binary forms,
with or without modification, are permitted
provided that the following conditions are met:
48GB
1 Redistributions of source code must retain the
above copyright notice, this list of conditions and
the following disclaimer.
2 Redistributions in binary form must reproduce
the above copyright notice, this list of conditions
and the following disclaimer in the
documentation and/or other materials provided
with the distribution.
3 Neither the name(s) of the above-listed copyright
holder(s) nor the names of its contributors may be
used to endorse or promote products derived
from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE
COPYRIGHT HOLDERS AND CONTRIBUTORS
“AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT
OWNER OR CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
• The system names and product names indicated in
this manual are generally the trademarks or
registered trademarks of the manufacturer.
• In this manual, Microsoft Windows XP Home
Edition, Microsoft Windows XP Professional and
Microsoft Windows XP Media Center Edition are
referred to as Windows XP.
• In this manual, Microsoft Windows Vista Home
Basic, Microsoft Windows Vista Home Premium,
Microsoft Windows Vista Business and Microsoft
Windows Vista Ultimate are referred to as
Windows Vista.
• In this manual, Microsoft Windows 7 Home Basic,
Microsoft Windows 7 Home Premium, Microsoft
Windows 7 Professional and Microsoft
Windows 7 Ultimate are referred to as Windows 7.
• ™ and ® marks are omitted in this manual.
END-USER LICENSE AGREEMENT FOR SONY SOFTWARE
You should carefully read the following agreement before using the SONY SOFTWARE (defined below). Using the SONY
SOFTWARE indicates your acceptance of the agreement. If you do not agree with it, you are not authorized to use the SONY
SOFTWARE.
IMPORTANT - READ CAREFULLY: This End-User License Agreement (“EULA”) is a legal agreement between you
and Sony Corporation (“SONY”), the manufacturer of your Sony hardware device (the “PRODUCT”) and the licensor of the
SONY SOFTWARE. All Sony software and third party software (other than such software subject to its own separate license)
included with your PRODUCT and any updates and upgrades thereto shall be referred to herein as the “SONY SOFTWARE”.
You may use the SONY SOFTWARE only with the PRODUCT.
By using the SONY SOFTWARE, you agree to be bound by the terms of this EULA. If you do not agree to the terms of this
EULA, SONY is unwilling to license the SONY SOFTWARE to you. In such event, you should not use the SONY
SOFTWARE.
SONY SOFTWARE LICENSE
The SONY SOFTWARE is protected by copyright laws and international copyright treaties, as well as other intellectual
property laws and treaties. The SONY SOFTWARE is licensed, not sold.
GRANT OF LICENSE
All title, copyright and other rights in and to the SONY SOFTWARE are owned by SONY or its licensors. This EULA grants
you the right to use the SONY SOFTWARE for personal use only.
DESCRIPTION OF REQUIREMENTS, RESTRICTIONS, RIGHTS AND LIMITATIONS
Limitations. You may not copy, modify, reverse engineer, decompile or disassemble the SONY SOFTWARE in whole or in
part.
Separation of Components. The SONY SOFTWARE is licensed as a single product. Its component parts may not be
separated.
Use on Single PRODUCT. The SONY SOFTWARE may only be used with a single PRODUCT.
Rental. You may not rent or lease the SONY SOFTWARE.
Software Transfer. You may permanently transfer all of your rights under this EULA only when the SONY SOFTWARE is
transferred together with and as part of the PRODUCT, provided that you retain no copies, transfer all of the SONY
SOFTWARE (including but not limited to all copies, component parts, media, instruction manuals, other printed materials,
electronic documents, recovery disks and this EULA) and the recipient agrees to the terms of this EULA.
Termination. Without prejudice to any other rights, SONY may terminate this EULA if you fail to comply with the terms of
this EULA. In such event, when requested by SONY, you must send the PRODUCT to an address designated by SONY, and
SONY will send back the PRODUCT to you as soon as practicable after the SONY SOFTWARE has been deleted from the
PRODUCT.
Confidentiality. You agree to keep confidential information contained in SONY SOFTWARE which is not publicly known
and not to disclose such information to others without SONY’s prior written approval.
HIGH RISK ACTIVITIES
The SONY SOFTWARE is not fault-tolerant and is not designed, manufactured or intended for use or resale as on-line control
equipment in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life support machines or weapons systems, in which the failure
of the SONY SOFTWARE could lead to death, personal injury or severe physical or environmental damage (“High Risk
Activities”). SONY and its suppliers specifically disclaim any express or implied warranty of fitness for High Risk Activities.
49GB
EXCLUSION OF WARRANTY ON SONY SOFTWARE
You expressly acknowledge and agree that use of the SONY SOFTWARE is at your sole risk. The SONY SOFTWARE is
provided “AS IS” and without warranty of any kind, and SONY, its vendors and SONY’s licensors (for purposes of this
SECTION only, collectively, “SONY”) EXPRESSLY DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. SONY DOES NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE SONY
SOFTWARE ARE FREE FROM ERRORS OR BUGS OR WILL MEET YOUR REQUIREMENT, AND SONY DOES
NOT WARRANT THAT THE OPERATION OF THE SONY SOFTWARE WILL BE CORRECTED. FURTHERMORE,
SONY DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF
THE USE OF THE SONY SOFTWARE IN TERMS OF ITS CORRECTNESS, ACCURACY, RELIABILITY OR
OTHERWISE. NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY SONY OR A SONY AUTHORIZED
REPRESENTATIVE SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS
WARRANTY. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, IN WHICH
CASE THE ABOVE EXCLUSION WOULD NOT APPLY TO YOU.
Without limiting any of the foregoing, it is specifically provided that the SONY SOFTWARE is not designed or intended for
use on any product other than the PRODUCT. SONY provides no warranty that any product, software, content or data created
by you or a third party will not be damaged by the SONY SOFTWARE.
LIMITATION OF LIABILITY
SONY, ITS SUPPLIERS AND SONY’S LICENSOR’S (for purposes of this SECTION ONLY, collectively, “SONY”)
SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RELATING TO THE SONY
SOFTWARE ARISING FROM OR BASED ON BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF
CONTRACT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE,
BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE
PRODUCT OR ANY ASSOCIATED EQUIPMENT, DOWN TIME AND USER’S TIME, REGARDLESS OF WHETHER
SONY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN ANY CASE, SONY’S ENTIRE
LIABILITY TO YOU UNDER ANY PROVISION OF THIS EULA SHALL BE LIMITED TO THE AMOUNT
ACTUALLY PAID ALLOCABLE TO THE SONY SOFTWARE.
EXPORTS
If you use or transfer the SONY SOFTWARE in or to a country other than your country of residence, you shall comply with
applicable laws and regulations relating to exports, imports and customs.
GOVERNING LAW
This EULA shall be construed, governed, interpreted and applied in accordance with the laws of Japan, without regards to any
conflict of laws provisions. Any dispute arising out of this EULA shall be subject to the exclusive venue and jurisdiction of
the courts in Tokyo, Japan, and you and SONY hereby consent to the venue and jurisdiction of such courts. YOU AND SONY
WAIVE THE RIGHT TO TRIAL BY JURY WITH RESPECT TO ANY MATTERS ARISING UNDER OR RELATING
TO THIS EULA.
SEVERABILITY
If any part of this EULA is held invalid or unenforceable, other parts will remain valid.
Should you have any questions in connection with this EULA or the limited warranty provided hereunder, you may contact
SONY by writing to SONY at the designated contact address mentioned in the warranty card included in the product package.
50GB
For customer in the U.S.A
END-USER LICENSE AGREEMENT FOR SONY SOFTWARE
(for the application included in the supplied CD-ROM)
YOU SHOULD CAREFULLY READ THE FOLLOWING AGREEMENT BEFORE USING THIS SOFTWARE. USING
THIS SOFTWARE INDICATES YOUR ACCEPTANCE OF THE AGREEMENT.
IMPORTANT-READ CAREFULLY: This End-User License Agreement (“LICENSE”) is a legal agreement between you
and Sony Electronics Inc. (“SONY”) relating to the (i) software which is furnished on CD-ROM or DVD-ROM media and
bundled with the hardware device sold by SONY or its affiliate (“PRODUCT”), and (ii) software which is made available for
downloading and use from a website designated by SONY or its affiliate (“SONY SITE”), including software updates/
upgrades, in connection with the use of the PRODUCT (such (i) and (ii) are collectively referred to as “SOFTWARE”, which
shall include all associated media, printed materials and any online or electronic materials provided in connection therewith).
Notwithstanding the foregoing, software having a separate end user license agreement shall be covered by such a separate end
user license agreement and shall be expressly excluded from SOFTWARE. By installing, copying, downloading or otherwise
using the SOFTWARE, you agree to be bound by the terms of this LICENSE. If you do not agree to the terms of this
LICENSE, SONY is unwilling to license the SOFTWARE to you. In such event, you may not use or copy the SOFTWARE,
and you should promptly contact SONY for instructions on return of the entire PRODUCT and included SOFTWARE for a
refund of the purchase price of the PRODUCT.
SOFTWARE LICENSE
The SOFTWARE is protected by copyright laws and international copyright treaties, as well as other intellectual property
laws and treaties. The SOFTWARE is licensed, not sold.
GRANT OF LICENSE
This LICENSE grants you the following non-exclusive rights:
Software. You may install and use one copy of the SOFTWARE on your computer. Unless otherwise specified in the
documentation provided with the SOFTWARE or on the SONY SITE, you may install and use such SOFTWARE on only one
computer at a time.
Personal Use. You may use the SOFTWARE for personal use only.
Back-up Copy. You may make one back-up copy of the SOFTWARE solely for recovery purposes.
DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
Limitation on Reverse Engineering, Decompilation and Disassembly. You may not modify, reverse engineer, decompile,
or disassemble the SOFTWARE in whole or in part.
Separation of Components. The SOFTWARE is licensed as a single product. Its component parts may not be separated for
use on more than one computer unless expressly authorized by Sony.
Storage/Network Use. You may not use the SOFTWARE over a network or distribute the SOFTWARE to other computers
over a network except as specifically described in documentation provided with the SOFTWARE.
Non-Circumvention. You may not bypass, modify, defeat or circumvent any of the functions or protections of the
SOFTWARE or any mechanisms operatively linked to the SOFTWARE.
Trademarks and Notices. You may not remove, alter, cover or deface any trademarks or notices on the SOFTWARE.
Data Files. The SOFTWARE may create data files automatically for use with the SOFTWARE. Any such data files will be
deemed as part of the SOFTWARE.
Rental. You may not rent or lease the SOFTWARE.
SOFTWARE Transfer. You may permanently transfer all of your rights under this LICENSE only if you retain no copies,
transfer all of the SOFTWARE (including all copies, component parts, the media and printed materials, all versions and any
upgrades of the SOFTWARE and this LICENSE), and the recipient agrees to the terms of this LICENSE.
Dependent Software. The software, network services or other products other than SOFTWARE upon which the
SOFTWARE's performance depends might be interrupted or discontinued at the discretion of the suppliers (software
suppliers, service providers, or SONY). SONY and its suppliers do not warrant that the software, network services or other
products will continue to be available, or will operate without interruption or modification.
Termination. Without prejudice to any other rights, SONY may terminate this LICENSE if you fail to comply with the terms
and conditions of this LICENSE. In such event, you must destroy and/or erase all copies of the SOFTWARE and all of its
component parts within two (2) weeks from such termination and provide SONY proof of such destruction and/or erasure.
SURVIVAL
In the event that this LICENSE is terminated, the following sections shall survive: Termination, COPYRIGHT, EXCLUSION
OF WARRANTY ON SOFTWARE, LIMITATION OF LIABILITY, SOFTWARE DATA COLLECTION AND
MONITORING, SEVERABILITY, and JURY WAIVER.
51GB
COPYRIGHT
All title and copyright in and to the SOFTWARE (including but not limited to any images, photographs, animation, video,
audio, music, text and “applets”, incorporated into the SOFTWARE), and any copies of the SOFTWARE, are owned by
SONY, SONY’s affiliates or their suppliers. All rights not specifically granted under this LICENSE are reserved by SONY.
USE OF SOFTWARE WITH COPYRIGHTED MATERIALS
The SOFTWARE may be capable of being used by you to store, process and use content created by you and third parties.
Such content may be protected by copyright, other intellectual property laws, and/or agreements. You agree to use the
SOFTWARE only in compliance with all such laws and agreements that apply to such content. You agree that SONY may
take appropriate measures to protect copyright of content stored, processed or used by the SOFTWARE. Such measures
include, but are not limited to, counting the frequency of your backup and restoration through certain SOFTWARE features,
refusal to accept your request to enable restoration of data through certain SOFTWARE features and termination of this
LICENSE in the event of your use of the SOFTWARE in violation of this LICENSE or applicable laws, rules or regulations.
HIGH RISK ACTIVITIES
The SOFTWARE is not fault-tolerant and is not designed, manufactured or intended for use or resale as on-line control
equipment in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life support machines, or weapons systems, in which the
failure of the SOFTWARE could lead to death, personal injury, or severe physical or environmental damage (“High Risk
Activities”). SONY, SONY’s affiliates and each of their suppliers specifically disclaim any express or implied warranty of
fitness for High Risk Activities.
LIMITED WARRANTY ON CD-ROM/DVD-ROM MEDIA
In situations where the SOFTWARE is furnished on CD-ROM/DVD-ROM media, SONY warrants, for a period of ninety
(90) days from the date of its delivery to you, the CD-ROM/DVD-ROM media against defects in materials and workmanship
under normal use. This limited warranty extends only to you as the original licensee. SONY’s entire liability and your
exclusive remedy will be replacement of the CD-ROM/DVD-ROM media not meeting SONY’s limited warranty and which is
returned to SONY with proof of purchase in the form of a bill of sale (which is evidence that the CD-ROM/DVD-ROM media
is within the warranty period). SONY will have no responsibility to replace CD-ROM/DVD-ROM media damaged by
accident, abuse or misapplication. ANY IMPLIED WARRANTIES ON THE CD-ROM/DVD-ROM MEDIA, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO NINETY (90) DAYS FROM THE DATE OF DELIVERY. SOME JURISDICTIONS DO
NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THESE LIMITATIONS MAY
NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.
EXCLUSION OF WARRANTY ON SOFTWARE
You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk. The SOFTWARE is provided “AS IS”
and without warranty of any kind and SONY, SONY’s affiliates and their licensors (in this section, SONY, its affiliates and
their licensors shall be collectively referred to as “SONY”) EXPRESSLY DISCLAIM ALL WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SONY DOES NOT WARRANT THAT THE
FUNCTIONS CONTAINED IN THE SOFTWARE WILL MEET YOUR REQUIREMENTS, OR THAT THE OPERATION
OF THE SOFTWARE WILL BE ERROR FREE. SONY DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS
REGARDING THE USE OR THE RESULTS OF THE USE OF THE SOFTWARE IN TERMS OF ITS CORRECTNESS,
ACCURACY, RELIABILITY, OR OTHERWISE. NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY
SONY OR A SONY AUTHORIZED REPRESENTATIVE SHALL CREATE A WARRANTY OR IN ANY WAY
INCREASE THE SCOPE OF THIS LIMITED WARRANTY. SHOULD THE SOFTWARE PROVE DEFECTIVE YOU
(AND NOT SONY OR A SONY AUTHORIZED REPRESENTATIVE) ASSUME THE ENTIRE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION. SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OF IMPLIED WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
Without limiting the foregoing, you expressly understand that any other computer hardware, software, or data could be
damaged by installing or using the SOFTWARE on your computer and that SONY is not responsible for any such damage.
You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk and you are responsible for installation
of the SOFTWARE and use of the SOFTWARE with your PRODUCT.
LIMITATION OF LIABILITY
SONY, (IN THIS SECTION, SONY, ITS AFFILIATES AND THEIR RESPECTIVE LICENSORS SHALL BE
COLLECTIVELY REFERRED TO AS “SONY”) SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF
CONTRACT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER LEGAL THEORY RELATED TO THE
SOFTWARE OR THE PRODUCT. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS,
LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE SOFTWARE, PRODUCT OR ANY ASSOCIATED
HARDWARE, DOWN TIME AND USER'S TIME, EVEN IF SONY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN ANY CASE, SONY'S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE
52GB
SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID ALLOCABLE TO THE ASSOCIATED PRODUCT. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL OR INCIDENTAL
DAMAGES, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.
SOFTWARE DATA COLLECTION AND MONITORING
The SOFTWARE contains features which may allow SONY and/or third parties to collect data from, control and/or monitor
computers and devices running or interacting with the SOFTWARE. You hereby consent to such activities. SONY's current
privacy policy is located at http://products.sel.sony.com/SEL/legal/privacy.html. Please contact applicable third-parties for
privacy policies related to their software and services.
AUTOMATIC UPDATE FEATURE
From time to time, SONY or third parties may automatically update or otherwise modify the SOFTWARE, including, but not
limited to, for purposes of enhancement of security functions, error correction and improvement of functions, at such time as
you interact with SONY’s or third parties’ servers, or otherwise. Such updates or modifications may delete or change the
nature of features or other aspects of the SOFTWARE, including functions you may rely upon. You hereby agree that such
activities may occur at SONY’s sole discretion and that SONY may condition continued use of the SOFTWARE upon your
complete installation or acceptance of such update or modifications. Any updates/modifications shall be deemed to be, and
shall constitute part of, the SOFTWARE for purposes of this LICENSE. By acceptance of this LICENSE, you consent to such
updates/modifications.
MODIFICATION OF LICENSE
SONY reserves the right to amend the specific terms of this LICENSE at its sole discretion by notice to you at the email
address you provided to SONY as part of your registration, by posting amended terms at the SONY SITE, or any other legally
recognizable form of notice. If you do not agree to the amended terms, with notice to you by SONY before they take effect,
you must stop using the SOFTWARE. Your continued use of the SOFTWARE after notice shall be deemed to be your
agreement to be bound by such amendment.
PROHIBITION ON EXPORT
EXCEPT FOR EXPORT TO CANADA FOR USE IN CANADA BY CITIZENS OF THE UNITED STATES OR
CANADA, THE SOFTWARE AND ANY UNDERLYING TECHNOLOGY MAY NOT BE EXPORTED OUTSIDE THE
UNITED STATES OR TO ANY FOREIGN ENTITY OR “FOREIGN PERSON” AS DEFINED BY U.S. GOVERNMENT
REGULATIONS, INCLUDING, WITHOUT LIMITATION, ANYONE WHO IS NOT A CITIZEN, NATIONAL, OR
LAWFUL PERMANENT RESIDENT OF THE UNITED STATES. BY USING THE SOFTWARE, YOU ARE AGREEING
TO THE FOREGOING AND YOU ARE WARRANTING THAT YOU ARE NOT A “FOREIGN PERSON” OR UNDER
THE CONTROL OF A FOREIGN PERSON.
U.S. GOVERNMENT RESTRICTED RIGHTS
SOFTWARE is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the United States Government is
subject to restriction as set forth in subparagraph (c) (1) and (2) of the Commercial Computer Software-Restricted Rights at 48
CFR 52.227-19, as applicable. Manufacturer is Sony Electronics Inc., 16530 Via Esprillo, San Diego, CA 92127.
SEVERABILITY
If any part of this LICENSE is held invalid or unenforceable, the other parts will remain valid.
JURY WAIVER
This LICENSE shall be governed by the laws of the United States. THE PARTIES HEREBY WAIVE TRIAL BY JURY
WITH RESPECT TO ANY MATTERS ARISING UNDER TO RELATING TO THIS LICENSE.
THIRD PARTY BENEFICIARY
For all purposes of this LICENSE, each of SONY’s affiliates and third party licensors of any of the SOFTWARE shall be
expressly deemed an intended third party beneficiary of this LICENSE and shall have the right to enforce the terms and
conditions of this LICENSE.
Should you have any questions concerning this LICENSE or this limited warranty, you may contact SONY by writing to
SONY at Sony Technical Response Center, 12451 Gateway Boulevard, Fort Myers, Florida 33913.
200904-03
53GB
For customers in Canada
END-USER LICENSE AGREEMENT FOR SONY SOFTWARE
(for the application included in the supplied CD-ROM)
YOU SHOULD CAREFULLY READ THE FOLLOWING AGREEMENT BEFORE USING THIS SOFTWARE. USING
THIS SOFTWARE INDICATES YOUR ACCEPTANCE OF THE AGREEMENT.
IMPORTANT-READ CAREFULLY: This End-User License Agreement ("EULA") is a legal agreement between you and
Sony Electronics Inc. ("SONY") relating to the (i) software which is furnished on CD-ROM or DVD-ROM media and
bundled with the hardware device sold by SONY or its affiliate (“PRODUCT”), and (ii) software which is made available for
downloading and use from a website designated by SONY or its affiliate (“SONY SITE”), including software updates/
upgrades, in connection with the use of a PRODUCT (such (i) and (ii) are collectively referred to as “SOFTWARE”, which
term shall include all associated media, printed materials and any online or electronic materials provided in connection
therewith). Notwithstanding the foregoing, software having a separate end user license agreement shall be covered by such a
separate end user license agreement and shall be expressly excluded from SOFTWARE. By installing, copying, downloading
or otherwise using the SOFTWARE, you agree to be bound by the terms of this EULA. If you do not agree to the terms of this
EULA, SONY is unwilling to license the SOFTWARE to you. In such event, you may not use or copy the SOFTWARE, and
you should promptly contact SONY for further instructions.
SOFTWARE LICENSE
The SOFTWARE is protected by copyright laws and international copyright treaties, as well as other intellectual property
laws and treaties. The SOFTWARE is licensed, not sold.
GRANT OF LICENSE
This EULA grants you the following non-exclusive rights:
Software. You may install and use one copy of the SOFTWARE on your computer. Unless otherwise specified in the
documentation provided with the SOFTWARE or on the SONY SITE, you may install and use such SOFTWARE on only one
computer at a time.
Personal Use. You may use the SOFTWARE for personal use only.
Back-up Copy. You may make one back-up copy of the SOFTWARE solely for recovery purposes.
DESCRIPTION OF REQUIREMENTS, RESTRICTIONS, RIGHTS AND LIMITATIONS
Limitation on Reverse Engineering, Decompilation and Disassembly. You may not modify, reverse engineer, decompile,
or disassemble the SOFTWARE in whole or in part.
Storage/Network Use. You may not use the SOFTWARE over a network or distribute the SOFTWARE to other computers
over a network except as specifically described in documentation provided with the SOFTWARE.
Non-Circumvention. You may not bypass, modify, defeat or circumvent any of the functions or protections of the
SOFTWARE or any mechanisms operatively linked to the SOFTWARE.
Separation of Components. The SOFTWARE is licensed as a single product. Its component parts may not be separated for
use on more than one computer unless expressly authorized by Sony.
Data Files. The SOFTWARE may create data files automatically for use with the SOFTWARE. Any such data files will be
deemed as part of the SOFTWARE.
Trademarks and Notices. You may not remove, alter, cover or deface any trademarks or notices on the SOFTWARE.
Rental. You may not rent or lease the SOFTWARE.
SOFTWARE Transfer. You may permanently transfer all of your rights under this EULA provided you retain no copies,
transfer all of the SOFTWARE (including all copies, component parts, the media and printed materials, all versions and any
upgrades of the SOFTWARE and this EULA), and the recipient agrees to the terms of this EULA.
Termination. Without prejudice to any other rights, SONY may terminate this EULA if you fail to comply with the terms and
conditions of this EULA. In such event, you must destroy all copies of the SOFTWARE and all of its component parts within
two (2) weeks from the termination and provide SONY proof of such destruction and/or erasure.
Dependent Software. The software, network services or other products other than SOFTWARE upon which the
SOFTWARE's performance depends might be interrupted or discontinued at the discretion of the suppliers (software
suppliers, service providers, or SONY). SONY and its suppliers do not warrant that those software, network services or other
products will continue to be available, or will operate without interruption or modification.
SURVIVAL
In the event that this EULA is terminated, the following sections will survive: Termination, COPYRIGHT, EXCLUSION OF
WARRANTY ON SOFTWARE, LIMITATION OF LIABILITY, SOFTWARE DATA COLLECTION AND
MONITORING, SEVERABILITY, and GOVERNING LAW AND JURISDICTION.
COPYRIGHT
All title and copyright in and to the SOFTWARE (including but not limited to any images, photographs, animation, video,
audio, music, text and "applets", incorporated into the SOFTWARE), and any copies of the SOFTWARE, are owned by
54GB
SONY, SONY’s affiliates or their respective suppliers. All rights not specifically granted under this EULA are reserved by
SONY.
USE OF SOFTWARE WITH COPYRIGHTED MATERIALS
The SOFTWARE may be capable of being used by you to store, process and use content created by you and third parties.
Such content may be protected by copyright, other intellectual property laws, and/or agreements. You agree to use the
SOFTWARE only in compliance with all such laws and agreements that apply to such content. You agree that SONY may
take appropriate measures to protect copyright of content stored, processed or used by the SOFTWARE. Such measures
include, but are not limited to, counting the frequency of your backup and restoration through certain SOFTWARE features,
refusal to accept your request to enable restoration of data through certain SOFTWARE features and termination of this
EULA in the event of your use of the SOFTWARE in violation of this EULA or applicable laws.
HIGH RISK ACTIVITIES
The SOFTWARE is not fault-tolerant and is not designed, manufactured or intended for use or resale as on-line control
equipment in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life support machines, or weapons systems, in which the
failure of the SOFTWARE could lead to death, personal injury, or severe physical or environmental damage ("High Risk
Activities"). SONY, each of SONY’s affiliates and their respective suppliers specifically disclaim any express or implied
warranty of fitness for High Risk Activities.
LIMITED WARRANTY ON CD-ROM/DVD-ROM MEDIA
In situations where the SOFTWARE is furnished on CD-ROM/DVD-ROM media, SONY warrants that for a period of ninety
(90) days from the date of its delivery to you the CD-ROM/DVD-ROM media on which the SOFTWARE is furnished to you
will be free from defects in materials and workmanship under normal use. This limited warranty extends only to you as the
original licensee. SONY's entire liability and your exclusive remedy will be replacement of the CD-ROM/DVD-ROM media
not meeting SONY's limited warranty and which is returned to SONY with proof of purchase in the form of a bill of sale
evidencing that the CD-ROM/DVD-ROM media is within the warranty period. SONY will have no responsibility to replace
the CD-ROM/DVD-ROM media damaged by accident, abuse or misapplication. ANY IMPLIED WARRANTIES OR
CONDITIONS ON THE CD-ROM /DVD-ROM MEDIA, INCLUDING THE IMPLIED WARRANTIES OR CONDITIONS
OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO
NINETY (90) DAYS FROM THE DATE OF DELIVERY. SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY OR CONDITION LASTS, SO THESE LIMITATIONS MAY NOT APPLY
TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.
EXCLUSION OF WARRANTY ON SOFTWARE
You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk. The SOFTWARE is provided "AS IS"
and without warranty or condition of any kind and SONY, SONY’s affiliates and their respective licensors (in this Section,
SONY, its affiliates and their respective licensors shall be collectively referred to as "SONY") EXPRESSLY DISCLAIM
ALL WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OR CONDITIONS OF NON-INFRINGEMENT, MERCHANTABILITY AND/OR FITNESS
FOR A PARTICULAR PURPOSE. SONY DOES NOT WARRANT OR MAKE ANY REPRESENTATION THAT THE
FUNCTIONS CONTAINED IN THE SOFTWARE WILL MEET YOUR REQUIREMENTS, OR THAT THE OPERATION
OF THE SOFTWARE WILL BE CORRECTED. FURTHERMORE, SONY DOES NOT WARRANT OR MAKE ANY
REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE SOFTWARE IN TERMS OF
ITS CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. NO ORAL OR WRITTEN INFORMATION OR
ADVICE GIVEN BY SONY OR A SONY AUTHORIZED REPRESENTATIVE SHALL CREATE A WARRANTY OR
CONDITION OR IN ANY WAY INCREASE THE SCOPE OF THIS LIMITED WARRANTY. SHOULD THE
SOFTWARE PROVE DEFECTIVE YOU (AND NOT SONY OR A SONY AUTHORIZED REPRESENTATIVE)
ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR CONDITIONS, SO THE
ABOVE EXCLUSION MAY NOT APPLY TO YOU.
Without limiting the foregoing, SONY does not warrant that any computer hardware and software will not be damaged by the
SOFTWARE or any data you download using the SOFTWARE. You expressly acknowledge and agree that use of the
SOFTWARE is at your sole risk and you are responsible for installation of the SOFTWARE and use of the SOFTWARE with
your PRODUCT.
LIMITATION OF LIABILITY
SONY (IN THIS SECTION, SONY, ITS AFFILIATES AND THEIR RESPECTIVE LICENSORS SHALL BE
COLLECTIVELY REFERRED TO AS "SONY") SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY OR CONDITION,
BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER LEGAL THEORY RELATED TO
THE SOFTWARE OR THE PRODUCT. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF
PROFITS, LOSS OF REVENUE, LOSS OF DATA, LOSS OF USE OF THE SOFTWARE, PRODUCT OR ANY
ASSOCIATED HARDWARE, DOWN TIME AND USER'S TIME, EVEN IF SONY HAS BEEN ADVISED OF THE
55GB
POSSIBILITY OF SUCH DAMAGES. IN ANY CASE, SONY'S ENTIRE LIABILITY UNDER ANY PROVISION OF
THIS EULA SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID ALLOCABLE TO THE PRODUCT. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CONSEQUENTIAL OR INCIDENTAL
DAMAGES, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.
SOFTWARE DATA COLLECTION AND MONITORING
The SOFTWARE contains features which may allow SONY and/or third parties to collect data from, control and/or monitor
computers and devices running or interacting with the SOFTWARE. You hereby consent to such activities. SONY's current
privacy policy is located at http://products.sel.sony.com/SEL/legal/privacy.html. Please contact applicable third-parties for
privacy policies related to their software and services.
AUTOMATIC UPDATE FEATURE
From time to time, SONY or third parties may automatically update or otherwise modify the SOFTWARE, including, but not
limited to, for purposes of enhancement of security functions, error correction and improvement of functions, at such time as
you interact with SONY's or third parties' servers, or otherwise. Such updates or modifications may delete or change the
nature of features or other aspects of the SOFTWARE, including functions you may rely upon. You hereby agree that such
activities may occur at SONY's sole discretion and that SONY may condition continued use of the SOFTWARE upon your
complete installation or acceptance of such update or modifications. Any updates/modifications shall be deemed to be, and
shall constitute part of, the SOFTWARE for purposes of this EULA. By acceptance of this EULA, you consent to such
updates/modifications.
MODIFICATION OF LICENSE
SONY reserves the right to amend the specific terms of this EULA at its sole discretion by notice to you at the email address
you provided to SONY as part of your registration, by posting amended terms at the SONY SITE, or any other legally
recognizable form of notice. If you do not agree to the amended terms, with notice to you by SONY before they take effect,
you must stop using the SOFTWARE. Your continued use of the SOFTWARE after notice shall be deemed to be your
agreement to be bound by such amendment.
EXPORT
EXCEPT FOR EXPORT TO CANADA OR FOR USE IN CANADA BY CITIZENS OF THE UNITED STATES OR
CANADA, THE SOFTWARE AND ANY UNDERLYING TECHNOLOGY MAY NOT BE EXPORTED OUTSIDE THE
UNITED STATES OR TO ANY FOREIGN ENTITY OR “FOREIGN PERSON” AS DEFINED BY U.S. GOVERNMENT
REGULATIONS, INCLUDING WITHOUT LIMITATION, ANYONE WHO IS NOT A CITIZEN, NATIONAL, OR
LAWFUL PERMANENT RESIDENT OF THE UNITED STATES. BY USING THE SOFTWARE, YOU ARE AGREEING
TO THE FOREGOING AND YOU ARE WARRANTING THAT YOU ARE NOT A “FOREIGN PERSON” OR UNDER
THE CONTROL OF A FOREIGN PERSON.
You shall comply with all applicable export, import and customs laws and regulations if you use the SOFTWARE outside the
country in which you reside.
U.S. GOVERNMENT RESTRICTED RIGHTS
SOFTWARE is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the United States Government is
subject to restriction as set forth in subparagraph (c)(1) and (2) of the Commercial Computer Software-Restricted Rights at 48
C.F.R. 52.2227-19, as applicable. Manufacturer is Sony Electronics Inc., 16530 Via Esprillo, San Diego, CA 92127.
SEVERABILITY
If any part of this EULA is held invalid or unenforceable, the other parts will remain valid.
GOVERNING LAW AND JURISDICTION
This LICENSE shall be governed by the laws of the state or province in which you reside, without regard to conflict of laws
provisions. THE PARTIES HEREBY WAIVE TRIAL BY JURY WITH RESPECT TO ANY MATTERS ARISING UNDER
TO RELATING TO THIS LICENSE.
THIRD PARTY BENEFICIARY
For all purposes of this EULA, each of SONY's affiliates and third party licensors of any of the SOFTWARE shall be
expressly deemed an intended third party beneficiary of this EULA and shall have the right to enforce the terms and
conditions of this EULA.
Should you have any questions concerning this EULA or this limited warranty, you may contact SONY by writing to SONY
at Sony Technical Response Center, 12451 Gateway Boulevard, Fort Myers, Florida 33913.
56GB
For customers in countries/regions other than the U.S.A. and Canada
END-USER LICENSE AGREEMENT FOR SONY SOFTWARE
(for the application included in the supplied CD-ROM)
YOU SHOULD CAREFULLY READ THE FOLLOWING AGREEMENT BEFORE USING THIS SOFTWARE. USING
THIS SOFTWARE INDICATES YOUR ACCEPTANCE OF THE AGREEMENT.
IMPORTANT-READ CAREFULLY: This End-User License Agreement ("EULA") is a legal agreement between you and
Sony Corporation ("SONY") relating to the (i) software which is furnished on CD-ROM/DVD-ROM and bundled with the
hardware device that is sold by SONY or its affiliates and (ii) software which is made available for downloading and use from
the website designated by SONY or its affiliates ((i) and (ii) are collectively referred to as, “SOFTWARE”). Notwithstanding
the foregoing, software having a separate end user license agreement shall be covered by such a separate end user license
agreement and shall be expressly excluded from SOFTWARE. By installing, copying, downloading or otherwise using the
SOFTWARE, you agree to be bound by the terms of this EULA. If you do not agree to the terms of this EULA, SONY is
unwilling to license the SOFTWARE to you. In such event, you may not use or copy the SOFTWARE, and you should
promptly contact SONY for instructions.
SOFTWARE LICENSE
The SOFTWARE is protected by copyright laws and international copyright treaties, as well as other intellectual property
laws and treaties. The SOFTWARE is licensed, not sold.
GRANT OF LICENSE
This EULA grants you the following non-exclusive rights:
Software. You may install and use one copy of the SOFTWARE on the computer. Unless otherwise specified in the
documentation provided with the SOFTWARE or on SONY- designated web site, you may install and use such SOFTWARE
on one unit of computer at a time.
Personal Use. You may use the SOFTWARE for personal use only.
Back-up Copy. You may make one back-up copy of the SOFTWARE solely for recovery purposes.
DESCRIPTION OF REQUIREMENTS, RESTRICTIONS, RIGHTS AND LIMITATIONS
Limitation on Reverse Engineering, Decompilation and Disassembly. You may not modify, reverse engineer, decompile,
or disassemble the SOFTWARE in whole or in part.
Separation of Components. The SOFTWARE is licensed as a single product. Its component parts may not be separated for
use on more than one computer unless expressly authorized by Sony.
Data Files. The SOFTWARE may create data files automatically for use with the SOFTWARE. Any such data files will be
deemed as part of the SOFTWARE.
Storage/Network Use. You may not use the SOFTWARE over a network or distribute the SOFTWARE to other computers
over a network except as specifically described in documentation provided with the SOFTWARE.
Rental. You may not rent or lease the SOFTWARE.
SOFTWARE Transfer. You may permanently transfer all of your rights under this EULA, provided you retain no copies,
transfer all of the SOFTWARE (including all copies, component parts, the media and printed materials, all versions and any
upgrades of the SOFTWARE and this EULA), and the recipient agrees to the terms of this EULA.
Termination. Without prejudice to any other rights, SONY may terminate this EULA if you fail to comply with the terms and
conditions of this EULA. In such event, you must destroy and/or erase all copies of the SOFTWARE and all of its component
parts within two weeks and provide SONY with proof of such destruction and/or erasure. The provisions of the following
captions shall survive any termination of this EULA;
Termination,
COPYRIGHTS
EXCLUSION OF WARRANTY ON SOFTWARE,
LIMITATION OF LIABILITY,
SOFTWARE DATA COLLECTION AND MONITORING,
SEVERABILITY, and
GOVERNING LAW AND JURISDICTION
Dependent Software. The software, network services or other products other than SOFTWARE upon which the
SOFTWARE's performance depends might be interrupted or discontinued at the discretion of the suppliers (software
suppliers, service providers, or SONY). SONY and its suppliers do not warrant that those software, network services or other
products will continue to be available, or will operate without interruption or modification.
COPYRIGHT
All title and copyright in and to the SOFTWARE (including but not limited to any images, photographs, animation, video,
audio, music, text and "applets", incorporated into the SOFTWARE), and any copies of the SOFTWARE, are owned by
SONY or its suppliers. All rights not specifically granted under this EULA are reserved by SONY.
57GB
USE OF SOFTWARE WITH COPYRIGHTED MATERIALS
The SOFTWARE may be capable of being used by you to store, process and use content created by you and third parties.
Such content may be protected by copyright, other intellectual property laws, and/or agreements. You agree to use the
SOFTWARE only in compliance with all such laws and agreements that apply to such content. You agree that SONY may
take appropriate measures to protect copyright of content stored, processed or used by the SOFTWARE. Such measures
include, but are not limited to, counting the frequency of your backup and restoration through certain SOFTWARE features,
refusal to accept your request to enable restoration of data through certain SOFTWARE features and termination of this
EULA in the event of your illegitimate use of the SOFTWARE.
HIGH RISK ACTIVITIES
The SOFTWARE is not fault-tolerant and is not designed, manufactured or intended for use or resale as on-line control
equipment in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft
navigation or communication systems, air traffic control, direct life support machines, or weapons systems, in which the
failure of the SOFTWARE could lead to death, personal injury, or severe physical or environmental damage ("High Risk
Activities"). SONY and its suppliers specifically disclaim any express or implied warranty of fitness for High Risk Activities.
LIMITED WARRANTY ON CD-ROM/DVD-ROM MEDIA
In situations where the SOFTWARE is furnished on CD-ROM or DVD-ROM media, SONY warrants that for a period of
ninety (90) days from the date of its delivery to you the CD-ROM or DVD-ROM media on which the SOFTWARE is
furnished to you will be free from defects in materials and workmanship under normal use. This limited warranty extends only
to you as the original licensee. SONY's entire liability and your exclusive remedy will be replacement of the CD-ROM or
DVD-ROM media not meeting SONY's limited warranty and which is returned to SONY with proof of purchase in the form
of a bill of sale (which is evidence that the CD-ROM or DVD-ROM media is within the warranty period). SONY will have no
responsibility to replace a disk damaged by accident, abuse or misapplication. ANY IMPLIED WARRANTIES ON THE CDROM OR DVD-ROM MEDIA, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO NINETY (90) DAYS FROM THE DATE OF
DELIVERY. SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THESE LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.
EXCLUSION OF WARRANTY ON SOFTWARE
You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk. The SOFTWARE is provided "AS IS"
and without warranty of any kind and SONY and SONY's licensors (hereinafter, SONY and SONY's licensor's shall be
collectively referred to as "SONY") EXPRESSLY DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. SONY DOES NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE
SOFTWARE WILL MEET YOUR REQUIREMENTS, OR THAT THE OPERATION OF THE SOFTWARE WILL BE
CORRECTED. FURTHERMORE, SONY DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING
THE USE OR THE RESULTS OF THE USE OF THE SOFTWARE IN TERMS OF ITS CORRECTNESS, ACCURACY,
RELIABILITY, OR OTHERWISE. NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY SONY OR A
SONY AUTHORIZED REPRESENTATIVE SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE
SCOPE OF THIS WARRANTY. SHOULD THE SOFTWARE PROVE DEFECTIVE YOU (AND NOT SONY OR A
SONY AUTHORIZED REPRESENTATIVE) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED
WARRANTIES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
SONY provides no warranty that any computer hardware and software will not be damaged by the SOFTWARE or any data
you download using the SOFTWARE. You expressly acknowledge and agree that use of the SOFTWARE is at your sole risk
and you are responsible for installation of the SOFTWARE and use of the SOFTWARE.
LIMITATION OF LIABILITY
HEREINAFTER, SONY, ITS AFFILIATES AND THEIR RESPECTIVE LICENSOR'S SHALL BE COLLECTIVELY
REFERRED TO AS "SONY", SONY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT,
NEGLIGENCE, STRICT LIABILITY OR ANY OTHER LEGAL THEORY RELATED TO THIS SOFTWARE. SUCH
DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF REVENUE, LOSS OF DATA,
LOSS OF USE OF THE SOFTWARE OR ANY ASSOCIATED HARDWARE, DOWN TIME AND USER'S TIME, EVEN
IF SONY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN ANY CASE, SONY'S ENTIRE
LIABILITY UNDER ANY PROVISION OF THIS EULA SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID
ALLOCABLE TO THE ASSOCIATED SOFTWARE. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF CONSEQUENTIAL OR INCIDENTAL DAMAGES, SO THE ABOVE EXCLUSION OR LIMITATION
MAY NOT APPLY TO YOU.
58GB
SOFTWARE DATA COLLECTION AND MONITORING
The SOFTWARE contains features which may allow SONY and/or third parties to collect data from, control and/or monitor
computers and devices running or interacting with the SOFTWARE. You hereby agree that such activities may occur. Please
contact applicable contact address of each country for SONY's current privacy policy.
AUTOMATIC UPDATE FEATURE
From time to time, SONY or third parties may automatically update or otherwise modify the SOFTWARE, for example, but
not limited to, for purposes of enhancement of security functions, error correction and improvement of functions, at such time
as you interact with SONY's or third parties' servers, or otherwise. Such updates or modifications may delete or change the
nature of features or other aspects of the SOFTWARE, including functions you may rely upon. You hereby agree that such
activities may occur at SONY's sole discretion and that SONY may condition continued use of the SOFTWARE upon your
complete installation or acceptance of such update or modifications. Any updates/modifications shall be deemed and shall
constitute part of the SOFTWARE for purposes of this EULA. By acceptance of this EULA, you consent to such update/
modification.
EXPORT
You shall comply with all applicable export, import and customs laws and regulations if you use the SOFTWARE outside the
country in which you reside.
SEVERABILITY
If any part of this EULA is held invalid or unenforceable, the other parts will remain valid.
GOVERNING LAW AND JURISDICTION
This EULA shall be governed by the laws of Japan, without regards to conflict of laws provisions. The parties hereby consent
to submit to the non-exclusive jurisdiction of the courts of Japan.
MODIFICATION
SONY RESERVES THE RIGHT TO AMEND THE SPECIFIC TERMS OF THE LICENSE REGARDING THE
SOFTWARE AT ITS SOLE DISCRETION BY NOTICE TO YOU AT THE E-MAIL ADDRESS YOU HAVE PROVIDED
TO SONY AS PART OF YOUR REGISTRATION, BY POSTING AMENDING TERMS AT SONY’S SITE, OR ANY
OTHER LEGALLY RECOGNIZABLE FORM OF NOTICE. If you do not agree to the terms to be amended, which shall be
notified to you by SONY before they take effect, you must stop using the SOFTWARE. Your continued use of the
SOFTWARE after notice shall be deemed agreement to be bound by such amendment.
THIRD PARTY BENEFICIARY
For all purposes of this EULA, each of SONY's third party licensors of any of the SOFTWARE shall be expressly deemed an
intended third party beneficiary of this EULA and shall have the right to enforce the terms and conditions of this EULA.
Should you have any questions concerning this EULA or this limited warranty, you may contact SONY by writing to SONY
at applicable contact address of each country.
200904-02
59GB
http://www.sony.net/sans
* 4 4 2 5 6 7 2 1 1 *
©2012 Sony Corporation Printed in China
4-425-672-11(1)

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement