Advertisement
Advertisement
DLPTM Projector HC1100 Controling the projector using a personal computer This projector can be controlled by connecting a personal computer with RS-232C terminal. PC-controllable functions : • Turning the power ON or OFF • Changing input signals • Inputting commands by pressing the buttons on the control panel and remote control • Menu setting Connection RS-232C cable to RS-232C terminal D-SUB 9-pin 8-pin Important: • Make sure that your computer and projector are turned off before connection. • Boot up the computer first, and then plug the power cord of the projector. (If you do not follow this instruction, the Comport may not function.) • Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details. 1) Interface PROTOCOL RS-232C BAUD RATE 9600 [bps] DATA LENGTH PARITY BIT STOP BIT 8 [bits] NONE 1 [bit] FLOW CONTROL NONE This projector uses RXD, TXD and GND lines for RS-232C control. For RS-232C cable,the reverse type cable should be used. 2) Control command diagram The command consists of the address code, function code, data code, and end code. The length of the command varies among the functions. HEX ASCII Address code 30h 30h Function code Function Data code Data '0' '0' Function Data [Address code] [Function code] [Data code] [End code] End code 0Dh 30h 30h (In ASCII code, '0' '0') fixed. A code of each fixed control move. A code of each fixed control data (number) and not always indicated. 0Dh (In ASCII code, ' ') fixed. 1 3) Control sequence (1) Send the command from the personal computer to the projector. (2) The projector will send a return command after it receives an end code. If the command is not received correctly, the projector will not send the return command. (3) The personal computer checks the command and confirms if the sent command has been executed or not. (4) This projector sends various codes other than the return code. When having a control sequence by RS232C, reject other codes from the personal computer. • During signal switching, the command may not take effect even when the projector sends the return command. After signal switching completes, wait for the mode indication to disappear before sending the next command. • When sending commands successively, wait to receive the return command of the current command before sending a next command. • Keep intervals of at least 400 ms between receipt of a return command and sending of a next command. [Example] When turning the power ON (Figures and symbols enclosed in quotation marks are ASCII codes.): Sending commands from the PC, etc. 30 30 21 0D '0' '0' '!' ' ' Status code from the projector Description Command for POWER ON 30 30 21 0D '0' '0' '!' ' ' Command receipt confirmation (Command echo back) • Any commands will not be executed for 10 seconds after the power is turned on. 4) Operation commands (Not executable in stand-by mode. When the commands for input select are sent while the splash screen is being displayed, the splash screen is only canceled.) The operation commands are used for the basic operation setting of this projector. They may not be executed while the signals are changed. The operation commands have no data codes. Operation POWER ON POWER OFF INPUT COMPUTER INPUT COMPONENT INPUT HDMI INPUT VIDEO INPUT S-VIDEO ASCII ! " _r1 _c1 _d1 _v1 _v2 HEX 21h 22h 5Fh 5Fh 5Fh 5Fh 5Fh Note 72h 63h 64h 76h 76h 31h 31h 31h 31h 32h This command is invalid for 1 minute after the power is turned off. This command is invalid for 1 minute after the power is turned on. This command will not be executed in Stand-by mode. This command will not be executed in Stand-by mode. This command will not be executed in Stand-by mode. This command will not be executed in Stand-by mode. This command will not be executed in Stand-by mode. [Example] When setting the input signal to COMPUTER (Figures and symbols enclosed in quotation marks are ASCII codes.): Sending commands from the PC, etc. 30 30 5F 72 31 0D '0' '0' '_' 'r' '1' ' ' Status code from the projector Description Command for setting the input signal to COMPUTER Command receipt confirmation (Command echo back) 30 30 5F 72 31 0D '0' '0' '_' 'r' '1' ' ' 5) Keystone commands (Not executable in stand-by mode. Possible only to read during muting.) The keystone commands are used for the keystone setting of this projector with the value. The value will vary depending on the installation conditions, etc.) ITEM ASCII KEYSTONE(Vertical) KS KEYSTONE(Horizontal) KSH HEX 4Bh 53h 4Bh 53h VALUE ±40 ±25 48h How to set the grade Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code. ASCII HEX '+' 2Bh '–' 2Dh '0' 30h '1' 31h '2' 32h '3' 33h '4' 34h '5' 35h 2 '6' 36h '7' 37h '8' 38h '9' 39h 6) Remote commands (Not executable in stand-by mode. When the remote commands are sent while the splash screen is being displayed, the splash screen is only canceled.) Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes. Button's name on remote { } $ % MENU ENTER AUTO POSITION ASPECT BLANK ASCII r53 r2b r4f r59 r54 r10 r09 re2 ra6 HEX 72h 72h 72h 72h 72h 72h 72h 72h 72h 35h 32h 34h 35h 35h 31h 30h 65h 61h 33h 62h 66h 39h 34h 30h 39h 32h 36h Button's name on remote AV MEMORY 1 AV MEMORY 2 AV MEMORY 3 CONTRAST BRIGHTNESS COLOR TEMP. GAMMA SHARPNESS KEYSTONE ASCII re4 re5 re6 rd0 rd1 rd4 rd5 rd6 r43 HEX 72h 72h 72h 72h 72h 72h 72h 72h 72h 65h 65h 65h 64h 64h 64h 64h 64h 34h 34h 35h 36h 30h 31h 34h 35h 36h 33h [Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII codes.): Sending commands from the PC, etc. 30 30 72 35 34 0D '0' '0' 'r' '5' '4' ' ' Status code from the projector Description Command operating the same as the MENU button Command receipt confirmation (Command echo back) 30 30 72 35 34 0D '0' '0' 'r' '5' '4' ' ' 7) Password lock commands The password lock commands control the password lock. The password lock enabling or disabling command is sent with a 4-digit figure (password) added to the end of the data code. When the password lock is enabled or disabled successfully, the projector sends a return command comprising the data code, password, and “1” at the end. When enabling or disabling the password lock fails, it sends a return command with “0” at the end. There is no reconfirmation of the password. ITEM Password lock enabling/ disabling ASCII PSLOCK HEX 50h 53h 4Ch 4Fh 43h 4Bh VALUE 0****(Disabling), 1****(DISPLAY INPUT) 2****(MENU ACCESS) **** is a 4-digit figure (password). 8) Reading command diagram The projectors operating status, such as POWER-ON / OFF and the currently selected input terminal, etc. can be monitored. POWER ON POWER OFF INPUT COMPUTER INPUT COMPONENT INPUT HDMI INPUT VIDEO INPUT S-VIDEO POWER ON/OFF INPOSSIBLE POWER ON/OFF POSSIBLE NO SIGNAL SUPPLIED SIGNAL SUPPLIED ASCII Function Data (Receive) vP 1 vP 0 vI r1 vI c1 vI d1 vI v1 vI v2 vPK 0 vPK 1 vSM 0 vSM 1 76h 76h 76h 76h 76h 76h 76h 76h 76h 76h 76h HEX Function Data (Receive) 50h 31h 50h 30h 49h 72h 31h 49h 63h 31h 49h 64h 31h 49h 76h 31h 49h 76h 32h 50h 4Bh 30h 50h 4Bh 31h 53h 4Dh 30h 53h 4Dh 31h The PC sends the command without attaching the data code to it. On the other hand, the projector attaches to the received command it’s current operating status as the data code and send it back to the PC. [Example ] When checking the currently selected input terminal (when the INPUT VIDEO is being selected) : Sending commands from the PC, etc. 30 30 76 49 0D '0' '0' 'v' 'I' ' ' Status code from the projector Description Command for checking the input terminal 30 30 76 49 76 31 0D '0' '0' 'v' 'I' 'v' '1' ' ' Check result (VIDEO) 3 9) Menu setting commands (Not executable in stand-by mode. Possible only to read during muting.) The menu setting commands are used for the menu setting of this projector. If the personal computer sends the command without attaching the data code, the projector attaches to the received command it’s current setting value as the data code and send it back to the PC. ITEM GAMMA MODE ASCII GS HEX 47h 53h GAMMA MODE-USER1 GAMMA MODE-USER2 CONTRAST BRIGHTNESS COLOR TEMP. GSU1 GSU2 PP QQ A 47h 47h 50h 51h 41h COLOR TEMP.-USER (CONTRAST) COLOR TEMP.-USER (BRIGHTNESS) COLOR TINT SHARPNESS BrilliantColorTM SCREEN SIZE VERTICAL LOCATION LAMP MODE AUTO POWER ON AUTO POWER OFF SPLASH SCREEN BACK COLOR IMAGE REVERSE TRIGGER OUT TEST PATTERN ASPECT P 50h VALUE 0 (SPORTS), 1 (VIDEO), 2 (CINEMA), 3 (USER1), 4 (USER2), 5(AUTO) 0 (SPORTS), 1 (VIDEO), 2 (CINEMA),±05±05±05 (HIGH, MID, LOW) 0 (SPORTS), 1 (VIDEO), 2 (CINEMA),±05±05±05 (HIGH, MID, LOW) ±30 ±30 1 (9300K), 2 (6500K), 3 (5900K), 4 (USER), 5 (HIGH BRIGHTNESS) ±30±30±30(R,G,B) Q 51h ±30±30±30(R,G,B) T S R WEH SCR IMP LM APON APOF SS BB IR SCT TP SC 54h 53h 52h 57h 53h 49h 4Ch 41h 41h 53h 42h 49h 53h 54h 53h ±10 ±10 ±05 53h 53h 50h 51h 45h 43h 4Dh 4Dh 50h 50h 53h 42h 52h 43h 50h 43h 55h 55h 48h 52h 50h 4Fh 4Fh 54h PASSWORD FUNCTION PSLOCK 50h 53h 4Ch 4Fh MENU POSITION CINEMA MODE VIDEO SIGNAL (VIDEO only) SET UP SCART INPUT LANGUAGE MP CINE VS 4Dh 43h 56h 50h 49h 53h STU SRT LG 53h 53h 4Dh 54h 52h 47h RESET ALL HORIZ.POSITION VERT.POSITION FINE SYNC. TRACKING COMPUTER INPUT OVER SCAN HOLD HOLD BEGIN HOLD END CLAMP POSITION CLAMP WIDTH VERT.SYNC. LPF SHUTTER-U SHUTTER-L SHUTTER-LS SHUTTER-RS RSTALL HP VP FN TRK CIN VOS HLD HLB HLE CLP CLW VSC LPF SHU SHL SHLS SHRS 52h 53h 54h 48h 50h 56h 50h 46h 4Eh 54h 52h 43h 49h 56h 4Fh 48h 4Ch 48h 4Ch 48h 4Ch 43h 4Ch 43h 4Ch 56h 53h 4Ch 50h 53h 48h 53h 48h 53h 48h 53h 48h 4Eh 55h 54h 41h 4Bh 4Eh 53h 44h 42h 45h 50h 57h 43h 46h 55h 4Ch 4Ch 52h 31h 32h 0-2 0 (16:9), 1 (CINEMA SCOPE 2.35:1) ±26 0 (STANDARD), 1 (LOW) 4Eh 0 (OFF), 1 (ON) 46h 00 (OFF) , 05, 10, 15, 30, 60 0 (OFF), 1 (ON) 0 (BLACK), 1 (BLUE) 0 (OFF), 1 (MIRROR), 2 (INVERT), 3 (MIRROR INVERT) 0 (OFF), 1 (ON) 0 (OFF), 1 (CROSS HATCH) 0 (AUTO), 1 (4:3), 2 (16:9), 3 (ZOOM1), 4 (ZOOM2) 5 (STRETCH), 6 (REAL) 43h 4Bh 0****(UNLOCK),1****(DISPLAY INPUT), 2****(MENU ACCESS), ****is a 4-digit figure(password) 0 (Upper left), 1 (Lower right) 45h 0 (OFF), 1 (AUTO) 0 (AUTO), 1 (NTSC), 2 (PAL), 3 (SECAM) , 4 (4.43NTSC), 5 (PAL-M), 6 (PAL-N), 7 (PAL-60) 0 (AUTO), 1 (OFF), 2 (3.75%), 3 (7.5%) 0 (OFF), 1 (ON) 0( ), 1 (English), 2 (Español), 3 (Deutsch) , 4 (Français), 5 (Italiano),6 ( ), 7 ( ), 8 ( ), 9( ) 4Ch 4Ch +:increment, -:decrement *1 +:increment, -:decrement *1 00 - 31 +:increment, -:decrement *1 0 (RGB), 1 (YCBCR/YPBPR), 2 (AUTO) 00-10 0 (OFF), 1 (ON) 00 - 99 00 - 99 001 - 255 01 - 63 0 (AUTO), 1 (OFF) 0 (OFF), 1 (ON) 00-32 00-32 53h 00-95 53h 00-95 *1 ) Setting range differs depending on the input signals. • Some commands are not executed depending on the input signal. The operational restrictions same as those on the menu setting are applied. Refer to “Menu operation” in the User Manual for more details. 4 [Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are ASCII codes.): Sending commands from the PC, etc. 30 30 41 50 4F 4E 31 0D '0' '0' 'A' 'P' 'O' 'N' '1' ' ' Status code from the projector 30 30 41 50 4F 4E 31 0D '0' '0' 'A' 'P' 'O' 'N' '1' ' ' Description Command for setting the AUTO POWER ON to ON Command receipt confirmation (Command echo back) The data code of BRIGHTNESS of USER of COLOR TEMP. consists of the R, G and B data. [Example 2] When setting the R data to +10, G data to 0, and B data to -5:(Figures and symbols enclosed in quotation marks are ASCII codes.): Sending commands from the PC, etc. 30 30 50 2B 31 30 2B 30 30 2D 30 35 0D '0' '0' 'Q' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' Status code from the projector 30 30 50 2B 31 30 2B 30 30 2D 30 35 0D '0' '0' 'Q' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' ' [Example 3] Description Command for setting the picture control Command receipt confirmation (Command echo back) When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in quotation marks are ASCII codes.): Sending commands from the PC, etc. 30 30 53 0D '0' '0' 'S' ' ' Status code from the projector 30 30 53 2B 31 30 0D '0' '0' 'S' '+' '1' '0' ' ' Description Command for checking the TINT setting Check result (+10) • To set TINT at 0, enter +00. (-00 is invalid.) [Example 4] When setting the REFERENCE of GAMMA MODE - USER 1 to CINEMA, HIGH to -2, MID to +3 and LOW to 0. (Figures and symbols enclosed in quotation marks are ASCII codes.): Sending commands from the PC, etc. 30 30 47 53 55 31 2B 32 20 30 32 2B 30 33 2B 30 30 OD '0' '0' 'G' 'S' 'U' '1' '+' '2' '-' '0' '2' '+''0' '3' '+' '0' '0' ' ' Status code from the projector 30 30 47 53 55 31 2B 32 20 30 32 2B 30 33 2B 30 30 OD '0' '0' 'G' 'S' 'U' '1' '+' '2' '-' '0' '2' '+''0' '3' '+' '0' '0' ' ' 5 Description Command for setting the REFERENCE of GAMMA MODE Command receipt confirmation (Command echo back) ">

Public link updated
The public link to your chat has been updated.
Advertisement