Procedure to test for microphone transmit and audio output (Macintosh)
FCC WARNINGS
1. Under the Apple Menu select System Preferences
This device complies with Part 15 of the FCC rules. Operation subject to the following two
conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limitations of a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate, radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio and television reception. There is no
guarantee, however, that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to correct the interference by one or
more of the following measures:
- reorient or relocate the receiving antenna
- increase the separation between the equipment and receiver
- connect the equipment to an outlet on a circuit different from that to which the receiver is
connected
- consult the dealer or an experienced radio/TV technician for help
<DISCLAIMER>The user is cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to operate the equipment.
All specifications and installation/usage procedures are subject to change without notice.
2. Choose System
3. Select Speech
4. Select Speech Recognition
5. Choose Settings
6. Select VXI USB 7.0
7. Click on Calibrate and follow the onscreen directions
8. Click Done
9. Quit System Preferences
VXI LIMITED WARRANTY
1. If your USB710 headset fails to work for any reason during the first year from the date of
purchase as shown by the purchaser's warranty registration, VXI will repair or replace the headset at
its election, free of charge. To register your VXI product, you may do so online at www.vxicorp.com
or by calling customer service at 800-742-8588. Without warranty registration, the warranty
period begins on the date of manufacture. Products returned to VXI after the one-year warranty
period will be repaired as "out of warranty" products, and purchaser will be billed for such
repairs pursuant to the Out-of-Warranty Repair provisions set forth below.
VXI USB710 Headset
USER GUIDE
2. The obligations of VXI under this warranty shall be limited to repair or replacement (at our
option) of any part returned, freight pre-paid, to VXI. Returned products require a Return
Authorization that may be requested from VXI at 800.742.8588 or www.vxicorp.com.
3. THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. Some jurisdictions do not permit the exclusion of implied warranties and the foregoing
exclusions may not apply to you.
4. In no event shall VXI be responsible for any other damages whatsoever including direct,
indirect, special, incidental, consequential or otherwise for breach of this or any other warranty,
express or implied.
OUT-OF-WARRANTY REPAIRS: VXI will repair out-of-warranty product for a charge that is
applicable as of the date of receipt by VXI. Call 1-800-742-8588 for current repair charges and
see return details above. Out-of-warranty repairs are warranted to be free from defects in
material and workmanship for ninety (90) days. Products returned to VXI for Out-of-Warranty
repairs, freight prepaid and with proper Return Authorization, will be return shipped to the
customer at VXI's expense.
VXI CORPORATION
One Front Street, Rollinsford, NH 03869
603-742-2888 Toll free 1-800-742-8588
website: www.vxicorp.com
2005 VXI Corporation PN202052A
connecting people to a digital world.
CHOOSE A SIDE FOR THE MICROPHONE
AND ADJUST HEADBAND
Determine which side of your head you prefer to locate
the microphone. The microphone rotates up and over to
place the microphone on the chosen side. The speaker
also rotates to adjust the cord if necessary. Slide
headband in or out of the side support for best fit.
speaker
WINDOWS INSTALLATION
MACINTOSH INSTALLATION
SYSTEM REQUIREMENTS: Your USB710 headset is compatible with Windows XP,
2000, Me and 98SE operating systems. Before installation, be sure your
computer is running and that you exit all running applications.
SYSTEM REQUIREMENTS: Compatible with Mac OS 9.0 and higher. Plug the USB710
headset into the Mac's USB port (not the keyboard USB hub).
NOTE: Windows will prompt you through the New Hardware
Wizard with windows such as the one at right. However in some
instances the New Hardware Wizard windows will not appear
while drivers are being installed. In this case, the drivers install
automatically.
A. Windows Add New Hardware Wizard – First Pass – USB Composite Device
Note: Windows 98 Second Edition Upgrade users may need the Windows 98 Second
Edition Upgrade CD-ROM available.
MICROPHONE ADJUSTMENT
Position the microphone so it is located one finger-width
from the corner of your mouth just below your bottom lip.
The microphone has the word TALK or a painted dot
printed on it (under the cushion). Be sure that this mark is
facing your mouth.
"TALK" or a painted dot
1.The Add New Hardware Wizard should detect the new “USB Composite Device.” Click
Next.
2.The next window asks, “What do you want Windows to do?” Select “Search for the
best driver for your device.” Click Next.
3.The next window asks, “Where do you want Windows to search?” Select the hard
drive only with the default location in the text box (either“C:\Windows” or
“C:\Windows\Options\Cabs” depending on your PC). Click Next.
4.The next window states, “Windows will now install the driver for ‘USB Composite
Device’.” Click Next.
5.Click Finish.
SELECT OUTPUT/INPUT SOUND SETTINGS
Open the Apple Menu
Open System Preferences
Choose Hardware
Select Sound
Select Output
Select VXI USB 7.0
Select Input
Select VXI USB 7.0
Quit System Preferences
TROUBLESHOOTING
Procedure to test for microphone transmit and audio output (Windows)
1.Put the headset on and position the microphone properly.
2.Select Start/Settings/Control Panel/Sound & Audio Devices- and verify that
USB Audio Device is selected as Preferred Device for Playback and is selected
as Preferred Device for Recording.
3. Check “Use Only Preferred Devices.”
4. Click OK to close Windows Audio Properties.
5.Select Start/Programs/Accessories/Entertainment/Sound Recorder.
6. Click on the red dot in the Sound Recorder to begin recording.
7. Speak into the headset microphone for about 10 seconds. You should see
CONNECTING THE USB CONNECTOR INTO THE COMPUTER
Insert the USB plug on the headset into an open USB port
on your computer (see photo, right). As soon as the
USB plug is inserted into the USB port, Windows will
detect the addition of the headset, and the Add New
Hardware Wizard will run automatically as described in
the steps below. Macintosh users select “output/input
device” (see instructions right).
B. Windows Add New Hardware Wizard – Second Pass – USB Human Interface
Device
The second pass of the Add New Hardware Wizard detects a USB Human Interface
Device. This portion of the installation proceeds like the first, but installs “USB
Human Interface Device" instead of “USB Composite Device”.
C. Windows Add New Hardware Wizard – Third Pass – USB Audio Device
The third pass of the Add New Hardware Wizard detects a USB Audio Device. This
portion of the installation proceeds like the first, but installs “USB Audio Device"
instead of “USB Composite Device”. The Windows drivers have now been
installed.
variations in the green wavelength meter.
8. Click on the square to stop recording.
9. Click on the triangle in the center to playback your recording. You should
hear your voice in your earpiece.
10. You have successfully installed your VXI USB710 headset.
11. For Internet Telephony Applications, it is highly recommended that you
rerun the AudioSetup Wizard for the VoIP provider.
12. For speech applications, verify that USB Audio Device is selected as
input/output source.
Macintosh audio testing on the back page.
">
