Aeg-Electrolux | HG995440XB | User manual | Aeg-Electrolux HG995440XB User Manual

Aeg-Electrolux HG995440XB User Manual
HG995440XB
USER
MANUAL
EN
User Manual
Hob
2
www.aeg.com
CONTENTS
1. SAFETY INFORMATION............................................................................................. 2
2. SAFETY INSTRUCTIONS.............................................................................................5
3. INSTALLATION............................................................................................................8
4. PRODUCT DESCRIPTION.........................................................................................11
5. DAILY USE.................................................................................................................. 11
6. HINTS AND TIPS........................................................................................................13
7. CARE AND CLEANING.............................................................................................13
8. TROUBLESHOOTING............................................................................................... 14
9. TECHNICAL DATA.................................................................................................... 15
10. ENERGY EFFICIENCY............................................................................................. 17
11. ELECTROLUX / AEG MAJOR APPLIANCES - WARRANTY CONDITIONS........17
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com/webselfservice
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1.
SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible for any injuries or
damages that are the result of incorrect installation or
ENGLISH
3
usage. Always keep the instructions in a safe and
accessible location for future reference.
1.1 Children and vulnerable people safety
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away from the appliance unless continuously
supervised.
Children of less than 3 years of age should be kept
away from the appliance unless continuously
supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of
it appropriately.
Keep children and pets away from the appliance when
it operates or when it cools down. Accessible parts
may become hot during use.
If the appliance has a child safety device, it should be
activated.
Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
1.2 General Safety
•
•
•
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements.
WARNING: Unattended cooking on a hob with fat or
oil can be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch
off the appliance and then cover flame e.g. with a lid
or a fire blanket.
4
www.aeg.com
•
•
•
•
•
•
•
•
•
•
•
CAUTION: The appliance must not be supplied
through an external switching device, such as a timer,
or connected to a circuit that is regularly switched on
and off by a utility.
CAUTION: The cooking process has to be supervised.
A short term cooking process has to be supervised
continuously.
WARNING: Danger of fire: Do not store items on the
cooking surfaces.
Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they
can get hot.
Do not use the appliance before installing it in the
built-in structure.
Do not use a steam cleaner to clean the appliance.
If the glass ceramic surface / glass surface is cracked,
switch off the appliance and unplug it from the mains.
In case the appliance is connected to the mains
directly using junction box, remove the fuse to
disconnect the appliance from power supply. In either
case contact the Authorised Service Centre.
In case of hotplate glass breakage:
– shut immediately off all burners and any electrical
heating element and isolate the appliance from the
power supply,
– do not touch the appliance surface,
– do not use the appliance.
If the supply cord is damaged, it must be replaced by
the manufacturer, an authorized Service or similarly
qualified persons in order to avoid a hazard.
Where the appliance is directly connected to the
power supply, an all-pole isolating switch with a
contact gap is required. Complete disconnection in
compliance with the conditions specified in
overvoltage category III must be guaranteed. The
earth cable is excluded from this.
When you route the mains cable, make sure that the
cable doesn't come into direct contact (for example
ENGLISH
•
5
using insulating sleeving) with parts that can reach
temperatures of more than 50°C above room
temperature.
WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by
the manufacturer of the appliance in the instructions
for use as suitable or hob guards incorporated in the
appliance. The use of inappropriate guards can cause
accidents.
2. SAFETY INSTRUCTIONS
This appliance is suitable for the
following markets: ZA
2.1 Installation
WARNING!
Only a qualified person must
install this appliance.
WARNING!
Risk of injury or damage to
the appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instructions
supplied with the appliance.
• Keep the minimum distance from
other appliances and units.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
• Protect the bottom of the appliance
from steam and moisture.
• Do not install the appliance adjacent
to a door or under a window. This
prevents hot cookware falling from
the appliance when the door or the
window is opened.
• If the appliance is installed above
drawers make sure that the space,
between the bottom of the appliance
and the upper drawer, is sufficient for
air circulation.
• The bottom of the appliance can get
hot. Make sure to install a non-
combustible separation panel under
the appliance to prevent access to the
bottom.
2.2 Electrical Connection
WARNING!
Risk of fire and electric
shock.
• All electrical connections should be
made by a qualified electrician.
• The appliance must be earthed.
• Before carrying out any operation
make sure that the appliance is
disconnected from the power supply.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Make sure the appliance is installed
correctly. Loose and incorrect
electricity mains cable or plug (if
applicable) can make the terminal
become too hot.
• Use the correct electricity mains
cable.
• Do not let the electricity mains cable
tangle.
• Make sure that a shock protection is
installed.
• Use the strain relief clamp on the
cable.
• Make sure the mains cable or plug (if
applicable) does not touch the hot
appliance or hot cookware, when you
connect the appliance to the near
sockets.
• Do not use multi-plug adapters and
extension cables.
6
www.aeg.com
• Make sure not to cause damage to
the mains plug (if applicable) or to the
mains cable. Contact our Authorised
Service Centre or an electrician to
change a damaged mains cable.
• The shock protection of live and
insulated parts must be fastened in
such a way that it cannot be removed
without tools.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• If the mains socket is loose, do not
connect the mains plug.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
• The electrical installation must have
an isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation
device must have a contact opening
width of minimum 3 mm.
2.3 Gas connection
• All gas connections should be made
by a qualified person.
• Before installation, make sure that the
local distribution conditions (nature of
the gas and gas pressure) and the
adjustment of the appliance are
compatible.
• Make sure that there is air circulation
around the appliance.
• The information about the gas supply
is on the rating plate.
• This appliance is not connected to a
device, which evacuates the products
of combustion. Make sure to connect
the appliance according to current
installation regulations. Pay attention
to requirements regarding adequate
ventilation.
2.4 Use
WARNING!
Risk of injury, burns and
electric shock.
• Remove all the packaging, labelling
and protective film (if applicable)
before first use.
• This appliance is for household use
only.
• Do not change the specification of
this appliance.
• Make sure that the ventilation
openings are not blocked.
• Do not let the appliance stay
unattended during operation.
• Set the cooking zone to “off” after
each use.
• Do not put cutlery or saucepan lids on
the cooking zones. They can become
hot.
• Do not operate the appliance with
wet hands or when it has contact with
water.
• Do not use the appliance as a work
surface or as a storage surface.
• When you place food into hot oil, it
may splash.
WARNING!
Risk of fire and explosion
• Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
• The vapours that very hot oil releases
can cause spontaneous combustion.
• Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
WARNING!
Risk of damage to the
appliance.
• Do not keep hot cookware on the
control panel.
• Do not let cookware boil dry.
• Be careful not to let objects or
cookware fall on the appliance. The
surface can be damaged.
• Never leave a burner on with empty
cookware or without cookware.
• Do not put aluminium foil on the
appliance.
• Cookware made of cast iron,
aluminium or with a damaged bottom
ENGLISH
•
•
•
•
•
•
•
•
•
•
•
can cause scratches on the glass /
glass ceramic. Always lift these
objects up when you have to move
them on the cooking surface.
Use only stable cookware with the
correct shape and diameter larger
than the dimensions of the burners.
Make sure cookware is centrally
positioned on the burners.
Do not use large cookware that
overlap the edges of the appliance.
This can cause damage to the
worktop surface.
Make sure the flame does not go out
when you quickly turn the knob from
the maximum to the minimum
position.
Use only the accessories supplied
with the appliance.
Do not install a flame diffuser on the
burner.
The use of a gas cooking appliance
results in the production of heat and
moisture. Provide good ventilation in
the room where the appliance is
installed.
Prolonged intensive use of the
appliance may call for additional
ventilation, for example opening of a
window, or more effective ventilation,
for example increasing the level of
mechanical ventilation where present.
This appliance is for cooking
purposes only. It must not be used for
other purposes, for example room
heating.
Do not let acid liquids, for example
vinegar, lemon juice or limescale
remover, touch the hob. This can
cause matt patches.
Discoloration of the enamel or
stainless steel has no effect on the
performance of the appliance.
2.5 Care and cleaning
WARNING!
Do not remove the buttons,
knobs or gaskets from the
control panel. Water may
get inside the appliance and
cause damage.
7
• Clean the appliance regularly to
prevent the deterioration of the
surface material.
• Deactivate the appliance and let it
cool down before you clean it.
• Disconnect the appliance from the
electrical supply before maintenance.
• Do not use water spray and steam to
clean the appliance.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use any abrasive products,
abrasive cleaning pads, solvents or
metal objects.
• Do not clean the burners in the
dishwasher.
2.6 Service
• To repair the appliance contact the
Authorised Service Centre.
• Use original spare parts only.
2.7 Disposal
WARNING!
Risk of injury or suffocation.
• Contact your municipal authority for
information on how to discard the
appliance correctly.
• Disconnect the appliance from the
mains supply.
• Cut off the mains electrical cable
close to the appliance and dispose of
it.
• Flat the external gas pipes.
8
www.aeg.com
3. INSTALLATION
WARNING!
Refer to Safety chapters.
3.1 Before the installation
Before you install the hob, write down
the information bellow from the rating
plate. The rating plate is on the bottom
of the hob.
Model .......................................
PNC .........................................
Serial number ...........................
3.2 Gas Connection
WARNING!
The following instructions
about installation,
connection and
maintenance must be
carried out by qualified
personnel in compliance
with standards and local
regulations in force.
Choose fixed connections or use a
flexible pipe in stainless steel in
compliance with the regulation in force.
If you use flexible metallic pipes, be
careful they do not come in touch with
mobile parts or they are not squeezed.
Also be careful when the hob is put
together with an oven.
Make sure that the gas
supply pressure of the
appliance obeys the
recommended values. The
adjustable connection is
fixed to the comprehensive
ramp by means of a
threaded nut G 1/2". Screw
the parts without force,
adjust the connection in the
necessary direction and
tighten everything.
A
B C
A. End of shaft with nut
B. Washer supplied with the appliance
C. Elbow supplied with the appliance
WARNING!
It is important to install the
elbow correctly. Make sure
that the shoulder is on the
end of the thread. Then
install it on the hob
connecting pipe. Incorrect
assembly may cause a gas
leakage.
Liquid gas
Use the rubber pipe holder for liquid
gas. Always engage the gasket. Then
continue with the gas connection.
The flexible pipe is prepared for apply
when:
• it can not get hot more than room
temperature, higher than 30°C;
• it is no longer than 1500 mm;
• it shows no throttles;
• it is not subject to traction or torsion;
• it does not get in touch with cutting
edges or corners;
• it can be easily examined in order to
make sure its condition.
The control of preservation of the flexible
pipe consists in checking that:
• it does not show cracks, cuts, marks of
burnings on the two ends and on its
full length;
• the material is not hardened, but
shows its correct elasticity;
• the fastening clamps are not rusted;
• expired term is not due.
If one or more defects are visible, do not
repair the pipe, but replace it.
ENGLISH
WARNING!
When installation is
complete, make sure that
the seal of each pipe fitting
is correct. Use a soapy
solution, not a flame!
3.3 Injectors replacement
1. Remove the pan supports.
2. Remove the caps and crowns of the
burner.
3. With a socket spanner 7 remove the
injectors and replace them with the
ones which are necessary for the type
of gas you use (see table in
"Technical Data" chapter).
4. Assemble the parts, follow the same
procedure backwards.
5. Replace the rating plate (it is near the
gas supply pipe) with the one for the
new type of gas supply. You can find
this plate in the package supplied
with the appliance.
If the supply gas pressure is changeable
or different from the necessary pressure,
you must fit an applicable pressure
adjuster on the gas supply pipe.
3.4 Adjustment of minimum
level
To adjust the minimum level of the
burners:
1. Light the burner.
2. Turn the knob on the minimum
position.
3. Remove the knob.
4. With a thin screwdriver, adjust the
bypass screw position (A).
A
9
• from liquid gas to natural gas G20
20 mbar, undo the bypass screw
approximately 1/4 of a turn (1/2 of
a turn for Triple Crown burner).
WARNING!
Make sure the flame does
not go out when you quickly
turn the knob from the
maximum position to the
minimum position.
3.5 Electrical connection
• Make sure that the rated voltage and
type of power on the rating plate
agree with the voltage and the power
of the local power supply.
• This appliance is supplied with a
mains cable. It has to be supplied with
a correct plug which can hold the load
that the rating plate rates. Make sure
that you install the plug in a correct
socket.
• Always use a correctly installed
shockproof socket.
• Make sure that there is an access to
the mains plug after the installation.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• There is a risk of fire when the
appliance is in connection with an
extension cable, an adapter or a
multiple connection. Make sure that
the ground connection agrees with
the standards and regulations.
• Do not let the power cable to heat up
to a temperature higher than 90° C.
Make sure that you connect
the blue neutral cable to the
terminal with a letter "N" on
it. Connect the brown (or
black) phase cable to the
terminal which has a letter
"L". Keep the phase cable
connected at all times.
3.6 Connection cable
5. If you change:
• from natural gas G20 20 mbar to
liquid gas, fully tighten the bypass
screw in.
To replace the connection cable use only
the special cable or its equivalent. The
cable type is: H05V2V2-F T90.
Make sure that the cable section is
applicable to the voltage and the
10
www.aeg.com
working temperature. The yellow / green
earth wire must be approximately 2 cm
longer than the brown (or black) phase
wire.
3.7 Assembly
A
1.
6.
A) supplied bracket
CAUTION!
Install the appliance only on
a worktop with flat surface.
2.
3.8 Possibilities for insertion
The panel installed below the hob must
be easy to remove and let an easy access
in case a technical assistance
intervention is necessary.
Kitchen unit with door
3.
min. 450 mm
min. 650 mm
min. 45 mm
40 mm
490+20 mm
880+20mm
min 6 mm
4.
A
B
min 20 mm
(max 150 mm)
60 mm
5.
A. Removable panel
B. Space for connections
min 30 mm
ENGLISH
Kitchen unit with oven
The electrical connection of the hob and
the oven must be installed separately for
safety reasons and to let easy remove
oven from the unit.
4. PRODUCT DESCRIPTION
4.1 Cooking surface layout
1
2
3
1
2
3
4
Auxiliary burner
Triple Crown burner
Semi-rapid burner
Control knobs
4
4.2 Control knob
Symbol
Symbol
Description
Description
ignition position / maximum gas supply
no gas supply / off position
minimum gas supply
5. DAILY USE
B. Thermocouple
C. Ignition candle
WARNING!
Refer to Safety chapters.
5.1 Burner overview
A
B
A
C
D
B
C
A. Burner cap and crown
A.
B.
C.
D.
Burner cap
Burner crown
Ignition candle
Thermocouple
11
12
www.aeg.com
5.2 Ignition of the burner
Always light the burner
before you put on the
cookware.
WARNING!
Be very careful when you use
open fire in the kitchen
environment. The
manufacturer declines any
responsibility in case of the
flame misuse.
1. Push the control knob down and turn
it counterclockwise to the maximum
gas supply position ( ).
2. Keep the control knob pushed for
equal or less than 10 seconds. This
lets the thermocouple warm up. If
not, the gas supply is interrupted.
3. Adjust the flame after it is regular.
If after some tries the burner
does not light, check if the
crown and its cap are in
correct positions.
WARNING!
Do not keep the control
knob pushed for more than
15 seconds. If the burner
does not light after 15
seconds, release the control
knob, turn it into off position
and try to light the burner
again after minimum 1
minute.
CAUTION!
In the absence of electricity
you can ignite the burner
without electrical device; in
this case approach the
burner with a flame, turn the
control knob counterclockwise to maximum gas
supply position and push it
down. Keep the control
knob pushed for equal or
less than 10 seconds to let
the thermocouple warm up.
If the burner accidentally
goes out, turn the control
knob to the off position and
try to light the burner again
after minimum 1 minute.
The spark generator can
start automatically when you
switch on the mains, after
installation or a power cut. It
is normal.
Each control knob has a pilot
light. It lights up when you
turn the control knob.
5.3 Turning the burner off
To put the flame out, turn the knob to
the off position
.
WARNING!
Always turn the flame down
or switch it off before you
remove the pans from the
burner.
ENGLISH
13
6. HINTS AND TIPS
CAUTION!
Make sure that the pots are
placed centrally on the
burner in order to get the
maximum stability and a
lower gas consumption.
WARNING!
Refer to Safety chapters.
6.1 Cookware
CAUTION!
Do not use cast iron pans,
clay or earthenware pots,
grill or toaster plates.
WARNING!
Do not put the same pan on
two burners.
WARNING!
Do not put unstable or
damaged pots on the burner
to prevent spills and injuries.
CAUTION!
Make sure that the bottoms
of pots do not stand too
close to the control knob,
otherwise the flame heats
the control knob up.
CAUTION!
Make sure that pot handles
are not above the front edge
of the cooktop.
CAUTION!
Liquids spilt during cooking
can cause the glass to break.
6.2 Diameters of cookware
Use cookware with
diameters applicable to the
size of burners.
Burner
Diameter of
cookware (mm)
Triple Crown
180 - 260
Semi-rapid (rear left)
120 - 240
Semi-rapid (rear right)
120 - 240
Semi-rapid (front right)
120 - 220
Auxiliary
80 - 180
7. CARE AND CLEANING
WARNING!
Refer to Safety chapters.
7.1 General information
• Clean the hob after each use.
• Always use cookware with a clean
base.
• Scratches or dark stains on the surface
have no effect on how the hob
operates.
• Use a special cleaner suitable for the
surface of the hob.
WARNING!
Do not use knives, scrapers
or similar instruments to
clean the surface of the glass
or the rims of the burners
and the frame (if applicable).
• Wash stainless steel parts with water,
and then dry them with a soft cloth.
7.2 Pan supports
The pan supports are not
resistant to washing in a
dishwasher. They must be
washed by hand.
1. Remove the pan supports to easily
clean the hob.
14
www.aeg.com
Be very careful when you
replace the pan supports
to prevent the hob top
from damage.
2. The enamel coating occasionally can
have rough edges, so be careful
when you wash the pan supports by
hand and dry them. If necessary,
remove stubborn stains with a paste
cleaner.
3. After you clean the pan supports,
make sure that they are in correct
positions.
4. For the burner to operate correctly,
make sure that the arms of the pan
supports are inserted in the recesses
of the enamelled plates.
otherwise, the dirt can cause damage
to the hob. Take care to avoid burns.
• Remove when the hob is sufficiently
cool: limescale rings, water rings, fat
stains, shiny metallic discoloration.
Clean the hob with a moist cloth and
a non-abrasive detergent. After
cleaning, wipe the hob dry with a soft
cloth.
• To clean the enamelled parts, caps
and crowns, wash them with warm
soapy water and dry them carefully
before you put them back on.
7.4 Cleaning the spark plug
This feature is obtained through a
ceramic ignition candle with a metal
electrode. Keep these components well
clean to prevent difficult lighting and
check that the burner crown holes are
not obstructed.
7.5 Periodic maintenance
Speak to your local Authorised Service
Centre periodically to check the
conditions of the gas supply pipe and
the pressure adjuster, if fitted.
7.3 Cleaning the hob
• Remove immediately: melted plastic,
plastic foil, sugar and food with sugar,
8. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
8.1 What to do if...
Problem
Possible cause
There is no spark when you
The hob is not connected to
try to activate the spark gen- an electrical supply or it is
erator.
connected incorrectly.
Remedy
Check if the hob is correctly
connected to the electrical
supply.
The fuse is blown.
Make sure that the fuse is
the cause of the malfunction.
If the fuse is blown again
and again, contact a qualified electrician.
Burner cap and crown are
placed incorrectly.
Place the burner cap and
crown correctly.
ENGLISH
15
Problem
Possible cause
Remedy
The flame extinguishes immediately after ignition.
Thermocouple is not heated
up sufficiently.
After lightning the flame,
keep the knob pushed for
equal or less than 10 seconds.
The flame ring is uneven.
Burner crown is blocked with Make sure that the injector is
food residues.
not blocked and the burner
crown is clean.
8.2 If you cannot find a
solution...
during the warranty period. The
instructions about the Service Centre and
conditions of guarantee are in the
guarantee booklet.
If you cannot find a solution to the
problem yourself, contact your dealer or
an Authorised Service Centre. Give the
data from the rating plate. Make sure,
you operated the hob correctly. If not the
servicing by a service technician or
dealer will not be free of charge, also
A
8.3 Labels supplied with the
accessories bag
Stick the adhesive labels as indicated
below:
B
MOD.
MOD.
PROD.NO.
PROD.NO.
SER.NO
SER.NO
DATA
DATA
C
MOD.
PROD.NO.
SER.NO.
0049
03 IT
MADE IN ITALY
A. Stick it on Guarantee Card and send
this part (if applicable).
B. Stick it on Guarantee Card and keep
this part (if applicable).
C. Stick it on instruction booklet.
9. TECHNICAL DATA
9.1 Hob dimensions
Width
TYPE
IP20
896 mm
16
www.aeg.com
Depth
516 mm
9.2 Bypass diameters
BURNER
Ø BYPASS 1/100 mm
Triple Crown
56
Semi-rapid
32
Auxiliary
28
9.3 Other technical data
TOTAL POWER:
Gas original:
G20 (2H) 20 mbar
10,5 kW
Gas replacement:
G30 (3+) 28-30 mbar
763 g/h
G31 (3+) 37 mbar
750 g/h
Electric supply:
220-240 V ~ 50-60 Hz
Appliance category:
II2H3+
Gas connection:
G 1/2"
Appliance class:
3
9.4 Gas burners for NATURAL GAS G20 20 mbar
BURNER
NORMAL POWER
kW
MINIMUM POWER
kW
INJECTOR MARK
Triple Crown
3,8
1,4
146
Semi-rapid
1,9
0,45
96
Auxiliary
1,0
0,33
70
9.5 Gas burners for LPG G30/G31 28-30/37 mbar
BURNER
NORMAL
MINIMUM INJECTOR
POWER kW POWER kW MARK
NOMINAL GAS FLOW g/h
G30 28-30
mbar
G31 37 mbar
Triple Crown 3,8
1,4
98
276
271
Semi-rapid
1,9
0,45
71
138
136
Auxiliary
1,0
0,33
50
73
71
ENGLISH
17
10. ENERGY EFFICIENCY
10.1 Product information according to EU 66/2014
Model identification
HG995440XB
Type of hob
Built-in hob
Number of gas burners
5
Energy efficiency per gas burner
(EE gas burner)
Middle - Triple Crown
55.1%
Left rear - Semi-rapid
61.6%
Right rear - Semi-rapid
61.6%
Right front - Semi-rapid
57.1%
Left front - Auxiliary
not applicable
Energy efficiency for the gas hob
(EE gas hob)
58.8%
EN 30-2-1: Domestic cooking appliances burning gas - Part 2-1 : Rational use of
energy - General
10.2 Energy saving
•
•
•
•
•
•
•
Before use, make sure that the burners and pan supports are assembled correctly.
Use cookware with diameters applicable to the size of burners.
Center the pot on the burner.
When you heat up water, use only the amount you need.
If it is possible, always put the lids on the cookware.
When the liquid starts to boil, turn down the flame to barely simmer the liquid.
If it is possible, use a pressure cooker. Refer to its user manual.
11. ELECTROLUX / AEG MAJOR APPLIANCES WARRANTY CONDITIONS
For domestic use only.
Not for commercial or industrial use.
Any alteration or modification of the
equipment voids the warranty.
Failure to use a certified electrician or
Electrolux authorised service agent or
genuine parts for installation or service
voids the warranty.
1. Electrolux / AEG warrants the
equipment against defective material
or faulty manufacture, provided it is
used for domestic purposes only, for
a period of 36 (thirty six) months,
from the date of purchase by the
original retail purchaser. This
warranty only applies to Electrolux
and AEG large appliances.
2. a. In the first 6 (six) months from
date of purchase, for valid
warranty claims, collection, return
and installation (Built-in and gas
appliances) of the appliance will
be free of charge within South
Africa if installed by an
authorized Electrolux service
agent.
b. For the remainder of the
warranty period where the
repaired appliance is used or
installed more than 50 kilometres
from the nearest Electrolux
service agent or elsewhere in
South Africa, travel costs to the
18
www.aeg.com
3.
4.
5.
6.
place of use or installation shall
be for the account of the
purchaser.
This warranty is given on condition
that only labour, parts and
accessories supplied by authorised
agents are at all times used in
connection with the appliance,
including the installation thereof, and
that an authorised Electrolux service
agent installs and/or services the
appliance.
Electrolux shall not be responsible
for damage of any kind resulting
from electricity fluctuations, faults in
the building wiring, faulty
installations, and improper use of
controls or failure to use the
appliance in accordance with the
operating instructions and/or general
misuse and/or abuse, or if not used
for domestic purposes only, or for
damage caused by a superior force
(vis maior). Any repair or tampering
by an unauthorised person or
attempt to repair or tamper with the
equipment, or use of parts not
supplied by authorised agents, or
alterations or modification to the
equipment, shall render the warranty
null and void.
After the first 6 (six) months from the
date of purchase, this warranty does
not apply to light bulbs, loose glass,
glass oven doors and enamelled
surfaces, filters and other parts
subject to wear and tear or
discolouring, as well as damage
caused by abrasive and highly
concentrated cleaners and/or
cleaning materials or cleaners
prohibited by the user manual.
Electrolux shall not be responsible in
terms of this warranty for the
replacement or repair of any part of
the equipment which may have been
damaged in transit if delivery is
undertaken by any party other than
Electrolux or an authorised agent.
7. All gas appliances are to be installed
by a gas installer, registered with
SAQCC GAS. Electrical appliances
are to be installed by a qualified
electrician who is an authorised
service agent or assisted by an
authorised service agent from who
proof of installation will be required.
8. Repairs carried out under warranty
have a guarantee period of 3 (three)
months on the parts and labour
supplied to repair the unit and does
not extend the warranty nor does it
start a new warranty. Parts removed
during guarantee repairs become the
property of Electrolux.
9. After expiry of 6 (six) months from the
date of purchase the warranty shall
be available only to the original retail
purchaser of Electrolux domestic
appliances from an authorised
Electrolux Dealer or Distributor and
only where the appliance has been
retained for use in the Republic of
South Africa.
10. Failure to produce documentary
proof of the date of original
acquisition by the original purchaser
to Electrolux or an authorised service
agent, will result in normal charges
being levied for travel costs, the work
carried out and the parts supplied,
unless a production date can be
proved to be within the 6 (six)
months preceding the warranty
claim.
11. After 6 (six) months from the date of
purchase of the appliance the liability
of Electrolux under this warranty is
limited to the replacement and/or
repair of the defective parts within
the warranty period and does not
extend to the installation or removal
of the appliance.
CUSTOMER CARE HELPLINE
0800 222 825
Service and Spares
In the event of your appliance requiring a service or if you wish to purchase spare parts,
contact your local Electrolux Service Centre by telephoning:
0800 222 825 (Tollfree in South Africa)
ENGLISH
19
Help us to help you Please determine your type of enquiry before writing or telephoning.
When you contact us we need to know:
•
•
•
•
•
Your name and telephone number
Date of Purchase and Invoice number
Physical address where appliance is located
Model and serial number of the appliance
Clear and concise details of the fault
Customer Care
For general enquiries or information regarding Electrolux / AEG appliances contact:
Customer Care Department
Electrolux South Africa (Pty) Ltd.
P.O. Box 50 Paarden Eiland, 7420
Cape Town
Electrolux appliances
AEG appliances
Telephone
00800 222 825
E-mail
service@electrolux.co.za
Website
www.electrolux.co.za
www.aeg.co.za
12. ENVIRONMENTAL CONCERNS
Recycle materials with the symbol .
Put the packaging in relevant containers
to recycle it. Help protect the
environment and human health by
recycling waste of electrical and
electronic appliances. Do not dispose of
*
appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
867329444-C-042019
www.aeg.com/shop
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising