Zanussi | ZGO98520BA | User manual | ZANUSSI ZGO98520BA User Manual

ZANUSSI ZGO98520BA User Manual
User Manual
GETTING
STARTED?
EASY.
ZGO98520BA
EN User Manual
Hob
AE
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts may become
hot during use.
If the appliance has a child safety device, it should be activated.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
•
•
•
2
WARNING: The appliance and its accessible parts become hot
during use. Care should be taken to avoid touching heating
elements.
WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire blanket.
•
•
•
•
•
•
•
•
•
•
•
•
CAUTION: The appliance must not be supplied through an
external switching device, such as a timer, or connected to a
circuit that is regularly switched on and off by a utility.
CAUTION: The cooking process has to be supervised. A short
term cooking process has to be supervised continuously.
WARNING: Danger of fire: Do not store items on the cooking
surfaces.
Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot.
Do not use the appliance before installing it in the built-in
structure.
Do not use a steam cleaner to clean the appliance.
If the glass ceramic surface / glass surface is cracked, switch
off the appliance and unplug it from the mains. In case the
appliance is connected to the mains directly using junction box,
remove the fuse to disconnect the appliance from power
supply. In either case contact the Authorised Service Centre.
In case of hotplate glass breakage:
– shut immediately off all burners and any electrical heating
element and isolate the appliance from the power supply,
– do not touch the appliance surface,
– do not use the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer, an authorized Service or similarly qualified
persons in order to avoid a hazard.
Where the appliance is directly connected to the power supply,
an all-pole isolating switch with a contact gap is required.
Complete disconnection in compliance with the conditions
specified in overvoltage category III must be guaranteed. The
earth cable is excluded from this.
When you route the mains cable, make sure that the cable
doesn't come into direct contact (for example using insulating
sleeving) with parts that can reach temperatures of more than
50°C above room temperature.
WARNING: Use only hob guards designed by the manufacturer
of the cooking appliance or indicated by the manufacturer of
the appliance in the instructions for use as suitable or hob
3
guards incorporated in the appliance. The use of inappropriate
guards can cause accidents.
SAFETY INSTRUCTIONS
This appliance is suitable for the following markets:
•
AE
INSTALLATION
WARNING! Only a qualified person
must install this appliance.
WARNING! Risk of injury or damage
to the appliance.
•
•
•
•
•
•
•
•
•
•
Remove all the packaging.
Do not install or use a damaged appliance.
Follow the installation instructions supplied with
the appliance.
Keep the minimum distance from other
appliances and units.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Seal the cut surfaces with a sealant to prevent
moisture to cause swelling.
Protect the bottom of the appliance from steam
and moisture.
Do not install the appliance adjacent to a door
or under a window. This prevents hot cookware
falling from the appliance when the door or the
window is opened.
If the appliance is installed above drawers make
sure that the space, between the bottom of the
appliance and the upper drawer, is sufficient for
air circulation.
The bottom of the appliance can get hot. Make
sure to install a non-combustible separation
panel under the appliance to prevent access to
the bottom.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
•
•
•
4
All electrical connections should be made by a
qualified electrician.
The appliance must be earthed.
Before carrying out any operation make sure
that the appliance is disconnected from the
power supply.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Make sure the appliance is installed correctly.
Loose and incorrect electricity mains cable or
plug (if applicable) can make the terminal
become too hot.
Use the correct electricity mains cable.
Do not let the electricity mains cable tangle.
Make sure that a shock protection is installed.
Use the strain relief clamp on the cable.
Make sure the mains cable or plug (if
applicable) does not touch the hot appliance or
hot cookware, when you connect the appliance
to the near sockets.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug (if applicable) or to the mains cable.
Contact our Authorised Service Centre or an
electrician to change a damaged mains cable.
The shock protection of live and insulated parts
must be fastened in such a way that it cannot be
removed without tools.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
If the mains socket is loose, do not connect the
mains plug.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type fuses
removed from the holder), earth leakage trips
and contactors.
The electrical installation must have an isolation
device which lets you disconnect the appliance
from the mains at all poles. The isolation device
must have a contact opening width of minimum
3 mm.
GAS CONNECTION
• All gas connections must be made by a qualified
person.
• Before installation, make sure that the local
distribution conditions (nature of the gas and
gas pressure) and the adjustment of the
appliance are compatible.
•
•
•
Make sure that there is air circulation around the
appliance.
The information about the gas supply is on the
rating plate.
This appliance is not connected to a device,
which evacuates the products of combustion.
Make sure to connect the appliance according
to current installation regulations. Follow the
requirements for adequate ventilation.
USE
•
•
•
•
•
•
•
•
•
•
•
•
WARNING! Risk of injury, burns and
electric shock.
•
•
Remove all the packaging, labelling and
protective film (if applicable) before first use.
This appliance is for household use only.
Do not change the specification of this
appliance.
Make sure that the ventilation openings are not
blocked.
Do not let the appliance stay unattended during
operation.
Set the cooking zone to “off” after each use.
Do not put cutlery or saucepan lids on the
cooking zones. They can become hot.
Do not operate the appliance with wet hands or
when it has contact with water.
Do not use the appliance as a work surface or
as a storage surface.
When you place food into hot oil, it may splash.
•
•
•
•
•
•
•
WARNING! Risk of fire and explosion
•
•
•
•
•
Fats and oil when heated can release flammable
vapours. Keep flames or heated objects away
from fats and oils when you cook with them.
The vapours that very hot oil releases can cause
spontaneous combustion.
Used oil, that can contain food remnants, can
cause fire at a lower temperature than oil used
for the first time.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
WARNING! Risk of damage to the
appliance.
•
•
•
•
•
Do not keep hot cookware on the control panel.
Do not let cookware boil dry.
Be careful not to let objects or cookware fall on
the appliance. The surface can be damaged.
Never leave a burner on with empty cookware or
without cookware.
Do not put aluminium foil on the appliance.
Cookware made of cast iron, aluminium or with
a damaged bottom can cause scratches on the
glass / glass ceramic. Always lift these objects
up when you have to move them on the cooking
surface.
Use only stable cookware with the correct
shape and diameter larger than the dimensions
of the burners.
Make sure cookware is centrally positioned on
the burners.
Do not use large cookware that overlap the
edges of the appliance. This can cause damage
to the worktop surface.
Make sure the flame does not go out when you
quickly turn the knob from the maximum to the
minimum position.
Use only the accessories supplied with the
appliance.
Do not install a flame diffuser on the burner.
The use of a gas cooking appliance results in
the production of heat and moisture. Provide
good ventilation in the room where the
appliance is installed.
Prolonged intensive use of the appliance may
call for additional ventilation, for example
opening of a window, or more effective
ventilation, for example increasing the level of
mechanical ventilation where present.
This appliance is for cooking purposes only. It
must not be used for other purposes, for
example room heating.
Do not let acid liquids, for example vinegar,
lemon juice or limescale remover, touch the hob.
This can cause matt patches.
Discoloration of the enamel or stainless steel
has no effect on the performance of the
appliance.
CARE AND CLEANING
WARNING! Do not remove the
buttons, knobs or gaskets from the
control panel. Water may get inside
the appliance and cause damage.
•
•
•
•
•
•
Clean the appliance regularly to prevent the
deterioration of the surface material.
Deactivate the appliance and let it cool down
before you clean it.
Disconnect the appliance from the electrical
supply before maintenance.
Do not use water spray and steam to clean the
appliance.
Clean the appliance with a moist soft cloth. Only
use neutral detergents. Do not use any abrasive
products, abrasive cleaning pads, solvents or
metal objects.
Do not clean the burners in the dishwasher.
5
SERVICE
• To repair the appliance contact the Authorised
Service Centre.
• Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
•
•
•
•
Contact your municipal authority for information
on how to discard the appliance correctly.
Disconnect the appliance from the mains
supply.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Flat the external gas pipes.
INSTALLATION
WARNING! Refer to Safety chapters.
BEFORE THE INSTALLATION
Before you install the hob, write down the
information below from the rating plate. The rating
plate is on the bottom of the hob.
Model .......................................
PNC .........................................
Serial number ...........................
GAS CONNECTION
WARNING! The following instructions
about installation, connection and
maintenance must be carried out by
qualified personnel in compliance with
standards and local regulations in
force.
Choose fixed connections or use a flexible pipe in
stainless steel in compliance with the regulation in
force. If you use flexible metallic pipes, be careful
they do not come in touch with mobile parts or they
are not squeezed. Also be careful when the hob is
put together with an oven.
Make sure that the gas supply
pressure of the appliance obeys the
recommended values. The adjustable
connection is fixed to the
comprehensive ramp by means of a
threaded nut R 1/2". Screw the parts
without force, adjust the connection in
the necessary direction and tighten
everything.
6
A
B C
A. End of shaft
B. Washer supplied with the appliance
C. Elbow supplied with the appliance
WARNING! It is important to install
the elbow correctly. Make sure that the
shoulder is on the end of the thread.
Then install it on the hob connecting
pipe. Incorrect assembly may cause a
gas leakage.
Liquid gas
Use the rubber pipe holder for liquid gas. Always
engage the gasket. Then continue with the gas
connection.
The flexible pipe is prepared for apply when:
• it can not get hot more than room temperature,
higher than 30°C;
• it is no longer than 1500 mm;
• it shows no throttles;
• it is not subject to traction or torsion;
• it does not get in touch with cutting edges or
corners;
• it can be easily examined in order to make sure
its condition.
The control of preservation of the flexible pipe
consists in checking that:
• it does not show cracks, cuts, marks of burnings
on the two ends and on its full length;
• the material is not hardened, but shows its
correct elasticity;
• the fastening clamps are not rusted;
• expired term is not due.
If one or more defects are visible, do not repair the
pipe, but replace it.
WARNING! When installation is
complete, make sure that the seal of
each pipe fitting is correct. Use a
soapy solution, not a flame!
INJECTORS REPLACEMENT
1. Remove the pan supports.
2. Remove the caps and crowns of the burner.
3. With a socket spanner 7 remove the injectors
and replace them with the ones which are
necessary for the type of gas you use (see
table in "Technical Data" chapter).
4. Assemble the parts, follow the same procedure
backwards.
5. Attach the label with the new type of gas
supply near the gas supply pipe. You can find
this label in the package supplied with the
appliance.
If the supply gas pressure is changeable or
different from the necessary pressure, you must fit
an applicable pressure adjuster on the gas supply
pipe.
ADJUSTMENT OF MINIMUM LEVEL
To adjust the minimum level of the burners:
1. Light the burner.
2. Turn the knob on the minimum position.
3. Remove the knob.
4. With a thin screwdriver, adjust the bypass
screw position (A).
A
ELECTRICAL CONNECTION
• Make sure that the rated voltage and type of
power on the rating plate agree with the voltage
and the power of the local power supply.
• This appliance is supplied with a mains cable. It
has to be supplied with a correct plug which
can hold the load that the rating plate rates.
Make sure that you install the plug in a correct
socket.
• Always use a correctly installed shockproof
socket.
• Make sure that there is an access to the mains
plug after the installation.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
• There is a risk of fire when the appliance is in
connection with an extension cable, an adapter
or a multiple connection. Make sure that the
ground connection agrees with the standards
and regulations.
• Do not let the power cable to heat up to a
temperature higher than 90° C.
Make sure that you connect the blue
neutral cable to the terminal with a
letter "N" on it. Connect the brown (or
black) phase cable to the terminal
which has a letter "L". Keep the phase
cable connected at all times.
CONNECTION CABLE
To replace the connection cable use only the
special cable or its equivalent. The cable type is:
H03V2V2-F T90.
Make sure that the cable section is applicable to
the voltage and the working temperature. The
yellow / green earth wire must be approximately 2
cm longer than the brown (or black) phase wire.
5. If you change:
• from natural gas G20 20 mbar to liquid gas,
fully tighten the bypass screw in.
• from liquid gas to natural gas G20 20 mbar,
undo the bypass screw approximately 1/4
of a turn (1/2 of a turn for Multi Crown
burner).
WARNING! Make sure the flame does
not go out when you quickly turn the
knob from the maximum position to the
minimum position.
7
ASSEMBLY
1.
5.
6.
A
2.
B
7.
A) supplied seal
B) supplied brackets
3.
min. 100 mm
min. 650 mm
min. 55 mm
30 mm
480 02 mm
+
830+02 mm
4.
CAUTION! Install the appliance only
on a worktop with flat surface.
POSSIBILITIES FOR INSERTION
The panel installed below the hob must be easy to
remove and let an easy access in case a technical
assistance intervention is necessary.
8
Kitchen unit with door
A. Removable panel
B. Space for connections
30 mm
A
60 mm
Kitchen unit with oven
min 20 mm
(max 150 mm)
The electrical connection of the hob and the oven
must be installed separately for safety reasons and
to let easy remove oven from the unit.
B
PRODUCT DESCRIPTION
COOKING SURFACE LAYOUT
1 Semi-rapid burner
2 Multi Crown burner
1
3 Auxiliary burner
4 Control knobs
2
3
4
CONTROL KNOB
Symbol
Description
no gas supply / off position
Symbol
Description
minimum gas supply
ignition position / maximum
gas supply
DAILY USE
WARNING! Refer to Safety chapters.
9
BURNER OVERVIEW
$
2. Keep the control knob pushed for equal or less
than 10 seconds. This lets the thermocouple
warm up. If not, the gas supply is interrupted.
3. Adjust the flame after it is regular.
If after some tries the burner does not
light, check if the crown and its cap
are in correct positions.
%
WARNING! Do not keep the control
knob pushed for more than 15
seconds. If the burner does not light
after 15 seconds, release the control
knob, turn it into off position and try to
light the burner again after minimum 1
minute.
&
'
CAUTION! In the absence of
electricity you can ignite the burner
without electrical device; in this case
approach the burner with a flame, turn
the control knob counter-clockwise to
maximum gas supply position and
push it down. Keep the control knob
pushed for equal or less than 10
seconds to let the thermocouple warm
up.
$
%
If the burner accidentally goes out,
turn the control knob to the off position
and try to light the burner again after
minimum 1 minute.
&
'
A.
B.
C.
D.
The spark generator can start
automatically when you switch on the
mains, after installation or a power cut.
It is normal.
Burner cap
Burner crown
Ignition candle
Thermocouple
The hob is supplied with the
progressive valves. They make the
flame regulation more precise.
IGNITION OF THE BURNER
Always light the burner before you put
on the cookware.
WARNING! Be very careful when you
use open fire in the kitchen
environment. The manufacturer
declines any responsibility in case of
the flame misuse.
1. Push the control knob down and turn it
counterclockwise to the maximum gas supply
position ( ).
10
TURNING THE BURNER OFF
To put the flame out, turn the knob to the off
position
.
WARNING! Always turn the flame
down or switch it off before you
remove the pans from the burner.
HINTS AND TIPS
WARNING! Refer to Safety chapters.
COOKWARE
CAUTION! Do not use cast iron pans,
clay or earthenware pots, grill or
toaster plates.
WARNING! Do not put the same pan
on two burners.
WARNING! Do not put unstable or
damaged pots on the burner to
prevent spills and injuries.
CAUTION! Make sure that the
bottoms of pots do not stand too
close to the control knob, otherwise
the flame heats the control knob up.
CAUTION! Make sure that pot
handles are not above the front edge
of the cooktop.
CAUTION! Liquids spilt during
cooking can cause the glass to break.
ENERGY SAVING
• If it is possible, always put the lids on the
cookware.
• When the liquid starts to boil, turn down the
flame to barely simmer the liquid.
DIAMETERS OF COOKWARE
Use cookware with diameters
applicable to the size of burners.
Burner
Diameter of cookware (mm)
Multi Crown
180 - 260
Semi-rapid
120 - 240
Auxiliary
80 - 180
CAUTION! Make sure that the pots
are placed centrally on the burner in
order to get the maximum stability and
a lower gas consumption.
CARE AND CLEANING
WARNING! Refer to Safety chapters.
GENERAL INFORMATION
• Clean the hob after each use.
• Always use cookware with a clean base.
• Scratches or dark stains on the surface have no
effect on how the hob operates.
• Use a special cleaner suitable for the surface of
the hob.
WARNING! Do not use knives,
scrapers or similar instruments to
clean the surface of the glass or the
rims of the burners and the frame (if
applicable).
•
Wash stainless steel parts with water, and then
dry them with a soft cloth.
PAN SUPPORTS
The pan supports are not resistant to
washing in a dishwasher. They must
be washed by hand.
1. Remove the pan supports to easily clean the
hob.
Be very careful when you replace
the pan supports to prevent the
hob top from damage.
2. The enamel coating occasionally can have
rough edges, so be careful when you wash the
pan supports by hand and dry them. If
necessary, remove stubborn stains with a paste
cleaner.
3. After you clean the pan supports, make sure
that they are in correct positions.
11
4. For the burner to operate correctly, make sure
that the arms of the pan supports are inserted
in the recesses of the enamelled plates.
REMOVING AND ASSEMBLING PAN
SUPPORTS
After cleaning of the hob, make sure that pan
supports are in a correct position. In order to place
a pan support properly, make sure that its arms fits
the cut-outs placed at the base of the burner as
shown in the picture. This way, a pan support is
stable and fixed.
•
•
dirt can cause damage to the hob. Take care to
avoid burns.
Remove when the hob is sufficiently cool:
limescale rings, water rings, fat stains, shiny
metallic discoloration. Clean the hob with a
moist cloth and a non-abrasive detergent. After
cleaning, wipe the hob dry with a soft cloth.
To clean the enamelled parts, caps and crowns,
wash them with warm soapy water and dry them
carefully before you put them back on.
CLEANING THE SPARK PLUG
This feature is obtained through a ceramic ignition
candle with a metal electrode. Keep these
components well clean to prevent difficult lighting
and check that the burner crown holes are not
obstructed.
PERIODIC MAINTENANCE
Speak to your local Authorised Service Centre
periodically to check the conditions of the gas
supply pipe and the pressure adjuster, if fitted.
CLEANING THE HOB
• Remove immediately: melted plastic, plastic
foil, sugar and food with sugar, otherwise, the
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
WHAT TO DO IF...
Problem
There is no spark when you try
to activate the spark generator.
12
Possible cause
Remedy
The hob is not connected to an
electrical supply or it is connected incorrectly.
Check if the hob is correctly
connected to the electrical
supply.
The fuse is blown.
Make sure that the fuse is the
cause of the malfunction. If the
fuse is blown again and again,
contact a qualified electrician.
Burner cap and crown are
placed incorrectly.
Place the burner cap and
crown correctly.
The flame extinguishes immediately after ignition.
Thermocouple is not heated up
sufficiently.
After lightning the flame, keep
the knob pushed for equal or
less than 10 seconds.
The flame ring is uneven.
Burner crown is blocked with
food residues.
Make sure that the injector is
not blocked and the burner
crown is clean.
IF YOU CANNOT FIND A SOLUTION...
If you cannot find a solution to the problem yourself,
contact your dealer or an Authorised Service
Centre. Give the data from the rating plate. Make
sure, you operated the hob correctly. If not the
servicing by a service technician or dealer will not
be free of charge, also during the warranty period.
A
The instructions about the Service Centre and
conditions of guarantee are in the guarantee
booklet.
LABELS SUPPLIED WITH THE ACCESSORIES
BAG
Stick the adhesive labels as indicated below:
B
MOD.
MOD.
PROD.NO.
PROD.NO.
SER.NO
SER.NO
DATA
DATA
C
0049
MOD.
PROD.NO.
SER.NO.
TYPE
IP20
03 IT
MADE IN ITALY
A. Stick it on Guarantee Card and send this part
(if applicable).
B. Stick it on Guarantee Card and keep this part
(if applicable).
C. Stick it on instruction booklet.
TECHNICAL DATA
HOB DIMENSIONS
Width
880 mm
Depth
510 mm
BYPASS DIAMETERS
BURNER
Ø BYPASS 1/100 mm
Multi Crown
57
Semi-rapid
35
Auxiliary
28
13
OTHER TECHNICAL DATA
TOTAL POWER:
Gas original:
G30/G31 (3B/P) 30/30 mbar
745 g/h
Gas replacement:
G20 (2H) 20 mbar
10,45 kW
Electric supply:
220-240 V ~ 50-60 Hz
Appliance category:
II2H3B/P
Gas connection:
R 1/2"
Appliance
class:
3
GAS BURNERS FOR LPG G30/G31 30/30 mbar
BURNER
NORMAL POWER MINIMUM POWNOMINAL GAS FLOW
INJECTOR MARK
kW
ER kW
g/h
Multi Crown
3,55
1,4
095
258
Semi-rapid
1,9
0,6
71
138
Auxiliary
1,0
0,33
50
73
GAS BURNERS FOR NATURAL GAS G20 20 mbar
BURNER
NORMAL POWER kW MINIMUM POWER kW
INJECTOR MARK
Multi Crown
3,9
1,4
146
Semi-rapid
1,85
0,6
92
Auxiliary
1,0
0,33
70
ENVIRONMENTAL CONCERNS
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
Recycle materials with the symbol
. Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
14
*
15
867356332-B-222019
WWW.ZANUSSI.COM/SHOP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising