Samsung | OM55N-D | User manual | Samsung OM55N-D User manual

Samsung OM55N-D User manual
Smart Signage User Manual (By Model)
This manual provides information about your Smart Signage including supported types and product specifications per model.
OMN (OM46N OM55N)
OMN-D (OM46N-D OM55N-D)
The colour and the appearance may differ depending on the product, and the content in the
manual is subject to change without prior notice to improve the performance.
An administration fee may be charged in the following situations:
(a) An engineer is called out at your request, but it is found that the product has no defect (i.e.,
where the user manual has not been read).
(b) You bring the unit to a repair centre, but it is found that the product has no defect (i.e.,
where the user manual has not been read).
You will be informed of the administration fee amount before a technician visits.
© Samsung Electronics
Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Trademarks other than Samsung Electronics are
property of their respective owners.
Table of contents
Preparations
Checking the Components
3
Ports
OM46N/OM55N
OM46N-D/OM55N-D
Anti-theft Lock
4
4
5
6
Before Installing the Product (Installation
Guide)
OM46N/OM55N
OM46N-D/OM55N-D
7
7
8
Installing the Wall Mount
Installing the Wall Mount
Wall Mount Kit Specifications (VESA)
11
11
11
Specifications
General
12
Preset Timing Modes
13
Appendix
Licence
15
2
Chapter 01
Preparations
Checking the Components
"" Contact the vendor where you
purchased the product if any
components are missing.
"" The appearance of the components
may differ from the images shown.
Quick Setup Guide
Warranty card
(Not available in some locations)
Regulatory guide
Power cord
"" A stand is not provided with the
product. To install a stand, you can
purchase one separately.
"" Use either the back-side magnet or
the double-sided tape depending
on where you want to attach the
external ambient light sensor.
The warranty for adhesiveness of the
double-sided tape applies to firsttime-use only.
Batteries (AAA x 2)
(Not available in some locations)
Remote Control
External ambient light sensor
HOLDER-GUIDE x 2 / Screw (M3
x L6) x 4
Top cover
External IR cable
(OMN x 1 / OMN-D x 2)
"" The external ambient light sensor is
marked with the label on the sensor
cable.
Power IN rubber
(Supported model: OMN-D)
(Supported model: OMN-D)
(Supported model: OMN-D)
3
Ports
"" The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Port
OM46N/OM55N
RS232C OUT
RS232C IN
RS232C
OUT / IN
AUDIO OUT
IR IN
Stick the receiver of an external IR
cable to this location when the cable
is not used or the product is moved.
AMBIENT
SENSOR IN
Air outlet
Outputs sound to an audio device via an audio cable.
IR IN
Connects to an external IR cable that receives signals from the remote control.
AMBIENT SENSOR IN
Used to supply power to the external sensor board and to receive signals from
the ambient light sensor.
USB ¨
Connect to a USB memory device.
LAN OUT
•• Wired LAN connection port used to connect an external device such as a
laptop to connect to the Internet.
•• Connects to MDC using a LAN cable. (10/100 Mbps)
LAN IN
Connects to MDC using a LAN cable. (10/100 Mbps)
LAN OUT
HDMI 1 IN
HDMI 2 IN
HDMI 1 IN
HDMI 2 IN
Air inlet
Connects to MDC using an RS232C adapter.
AUDIO OUT
USB
LAN IN
Description
Connects to a source device using a HDMI cable or HDMI-DVI cable.
DP IN
Connects to a PC using a DP cable.
HDMI OUT
Connects to another product using a HDMI cable.
DP IN
HDMI OUT
4
OM46N-D/OM55N-D
"" The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
"" Install this product for indoors only. Install the display labelled OUTDOOR in the direction of the window.
Port
Air outlet
Description
RS232C IN
Connects to MDC using an RS232C adapter.
IR IN
Connects to an external IR cable that receives signals from the remote control.
USB ¨
Connect to a USB memory device.
HDMI IN
Connects to a source device using a HDMI cable or HDMI-DVI cable.
LAN
•• Wired LAN connection port used to connect an external device such as a
laptop to connect to the Internet.
•• Connects to MDC using a LAN cable. (10/100 Mbps)
AMBIENT SENSOR IN
Used to supply power to the external sensor board and to receive signals from
the ambient light sensor.
Setting up Device ID
Air inlet
OMN-D model has separate remote sensors on the front and back sides.
Depending on the distance from the remote control or other surrounding conditions, it is possible both front and
back displays respond to the remote control signal. You can assign IDs to displays (INDOOR: 1, OUTDOOR: 2) and
follow the steps below to restrict remote control to one selected display only.
"" To reverse the remote controlled display after setting otherwise, first cancel the existing ID settings for the
INDOOR and OUTDOOR displays by pressing the UNSET button.
•• To select the INDOOR display only
1) Position the remote control facing the INDOOR IR sensor and press SET → 1 → E on the control.
2) Position the remote control facing the OUTDOOR IR sensor and press SET → 1 → E on the control.
•• To select the OUTDOOR display only
1) Position the remote control facing the INDOOR IR sensor and press SET → 2 → E on the control.
2) Position the remote control facing the OUTDOOR IR sensor and press SET → 2 → E on the control.
5
Anti-theft Lock
"" An anti-theft lock allows you to use the product securely even in public places.
"" The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
"" The following images are for reference only. Real-life situations may differ from what is shown in the images.
"" Supported models: OMN
To lock an anti-theft locking device:
1 Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2 Put one end of the cable through the loop on the other end.
3 Insert the locking device into the anti-theft lock slot at the back of the product.
4 Lock the locking device.
–– An anti-theft locking device can be purchased separately.
–– Refer to the user guide provided with your anti-theft locking device for details.
–– Anti-theft locking devices can be purchased at electronics retailers or online.
6
Before Installing the Product (Installation
Guide)
Ventilation
"" Contact Samsung Customer Service Centre for further details.
Installation on a Perpendicular Wall
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance
with the installation instructions.
A Minimum 60 mm
•• Ensure that an authorised installation company installs the wall mount.
"" When installing the product on a perpendicular wall, allow at least
60 mm of space between the product and wall surface for ventilation
and ensure that the ambient A temperature is kept below 30 °C.
•• Otherwise, it may fall and cause personal injury.
•• Make sure to install the specified wall mount.
B Ambient temperature: Under 30 °C
A
OM46N/OM55N
Tilting Angle and Rotation
B
"" Contact Samsung Customer Service Centre for further details.
•• The product can be tilted at a maximum angle of 15° from a perpendicular wall surface.
15°
"" Do not use this model installed on a ceiling, floor, or table.
7
OM46N-D/OM55N-D
"" Contact Samsung Customer Service Centre for further details.
"" Do not install this product near machinery that works with oil (e.g. gas stations). Oil mist
may cause fans to malfunction.
"" Do not use in Landscape mode for this model.
Ventilation
"" Do not block the ventilation openings on the top and bottom sides.
A Distance from the show-window > 100 mm
B
B Distance from the ceiling > 300 mm
C Distance from the floor > 100 mm
D Operation temperature range: 0~30 ℃ (under direct sunlight)
A
D
C
8
Installing the top cover
Install HOLDER-GUIDE x 2.
Place the top cover.
Insert the power cord into the power IN rubber and
connect the power cord.
Securely position the external IR cable and the
external ambient light sensor at the specified
location.
Connect cables, e.g. external IR cable, power cord,
HDMI cable, and organise them as shown in the
image.
9
Removing handles
Precautions for enclosure unit installation
Remove the handles from both sides of the
product.
If you want to make additional enclosure surrounding OMN-D product, refer to the following
guides.
•• There should be no glass in front and back of the Enclosure.
•• Don’t block the top and bottom vents of OMN-D product.
•• Open rate above 70% is recommended for Inlet/Outlet vent of Enclosure.
Place the screws back into the screw holes and
fasten them.
"" Remove the screw caps found at the
marked locations before installing on
the ceiling or with the stand.
10
Installing the Wall Mount
"" Supported models: OMN
Installing the Wall Mount
•• The wall mount kit (sold separately) allows you to mount the product on the wall.
•• The provided image is only for reference. For detailed information on installing the wall mount, see instructions provided with the wall mount.
•• We recommend you contact a technician for assistance when installing the wall mount bracket.
•• Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you select to install the wall mount on your own.
Wall Mount Kit Specifications (VESA)
•• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are
provided.
"" Install your wall mount on a solid wall perpendicular to the floor. To
install the product on the other wall area, contact the nearest agency.
If you install the product on a slanted wall, it may fall and result in
severe personal injury.
•• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw
specifications. Screws that are too long may cause damage to the inside of the product.
•• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may
differ depending on the wall mount specifications.
•• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to
personal injury. Samsung is not liable for these kinds of accidents.
•• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is
used or the consumer fails to follow the product installation instructions.
•• Do not mount the product at more than a 15 degree tilt.
•• Always have at least two people mount the product on a wall.
•• Standard dimensions for wall mount kits are shown in the table below.
Model Name
VESA screw hole specs (A * B) in
millimetres
Standard Screw
Quantity
OM46N / OM55N
400 × 400
M8
4
"" Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric
shock.
11
Chapter 02
Specifications
General
Model Name
Panel
OM46N / OM46N-D
OM55N / OM55N-D
Size
46 CLASS (45.9 inches / 116.8 cm)
55 CLASS (54.6 inches / 138.7 cm)
Display area
1018.08 mm (H) x 572.67 mm (V)
1209.6 mm (H) x 680.4 mm (V)
AC100-240V~ 50/60Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Power Supply
Operating
Temperature: 0 °C – 40 °C (32 °F – 104 °F)
* For installing the enclosure, keep the internal temperature at 40 °C or below.
Humidity: 10% – 80%, non-condensing
Storage
Temperature: -20 °C – 45 °C (-4 °F – 113 °F)
Humidity: 5% – 95%, non-condensing
* Applicable before the product package is unpacked.
Environmental considerations
"" Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimises the monitor settings. Monitor
installation takes place automatically. However, you can customise the installation settings if desired.
"" Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect product performance.
"" This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
"" For detailed device specifications, visit the Samsung Electronics website.
12
Preset Timing Modes
"" This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a
resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution
specified for your product.
"" Horizontal Frequency
The time required to scan a single
line from the left to the right side
of the screen is called a horizontal
cycle. The reciprocal number of a
horizontal cycle is called horizontal
frequency. Horizontal frequency is
measured in kHz.
Model Name
Synchronization
Resolution
Horizontal Frequency
Vertical Frequency
OM46N / OM55N
OM46N-D / OM55N-D
15 - 135 kHz (HDMI), 30 - 135 kHz (DisplayPort)
15 - 135 kHz (HDMI)
24 - 75 Hz (HDMI), 30 - 75 Hz (DisplayPort)
24 - 75 Hz (HDMI)
Optimum resolution
1920 x 1080 @ 60 Hz
Maximum resolution
3840 x 2160 @ 60 Hz
"" Vertical Frequency
The product displays a single image
multiple times per second (like a
fluorescent light) to display what
the viewer sees. The rate of a single
image being displayed repeatedly per
second is called vertical frequency
or refresh rate. Vertical frequency is
measured in Hz.
13
The screen will automatically be adjusted if a signal that belongs to the following standard
signal modes is transmitted from your PC. If the signal transmitted from the PC does not belong
to the standard signal modes, the screen may be blank with the power indicator on. In such a
case, change the settings according to the following table by referring to the graphics card user
manual.
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1366 x 768
47.712
59.790
85.500
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
VESA, 1920 x 1080
67.500
60.000
148.500
+/+
VESA, 2560 x 1440
88.787
59.951
241.500
+/-
CEA, 3840 x 2160
(HDMI)
67.500
60.000
297.000
+/+
VESA, 3840 x 2160
(DP)
133.313
59.997
533.250
+/-
"" The OMN-D models are not available in the VESA 3840 x 2160 (DP).
14
Chapter 03
Appendix
Licence
Manufactured under license from Dolby Laboratories.
Dolby, Dolby Audio, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
"" Supported models: OMN
The terms HDMI and HDMI High-Definition Multimedia Interface, and
the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the
product menu. Open Source Licence Notice is written only English.
THIS PRODUCT IS SOLD WITH A LIMITED LICENCE AND IS AUTHORISED TO BE USED
ONLY IN CONNECTION WITH HEVC CONTENT THAT MEETS EACH OF THE THREE
FOLLOWING QUALIFICATIONS: (1) HEVC CONTENT ONLY FOR PERSONAL USE; (2) HEVC
CONTENT THAT IS NOT OFFERED FOR SALE; AND (3) HEVC CONTENT THAT IS CREATED
BY THE OWNER OF THE PRODUCT.
THIS PRODUCT MAY NOT BE USED IN CONNECTION WITH HEVC ENCODED CONTENT
CREATED BY A THIRD PARTY, WHICH THE USER HAS ORDERED OR PURCHASED FROM
A THIRD PARTY, UNLESS THE USER IS SEPARATELY GRANTED RIGHTS TO USE THE
PRODUCT WITH SUCH CONTENT BY A LICENSED SELLER OF THE CONTENT.
YOUR USE OF THIS PRODUCT IN CONNECTION WITH HEVC ENCODED CONTENT IS
DEEMED ACCEPTANCE OF THE LIMITED AUTHORITY TO USE AS NOTED ABOVE.
For information on the Open Source Licence Notice, contact the Samsung Customer Centre
or send email to oss.request@samsung.com.
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising