Samsung | S27R750QEU | User manual | Samsung S27R750QEU User manual

Samsung S27R750QEU User manual
User Manual
S27R75* S32R75*
The colour and the appearance may differ depending on the product, and the specifications are subject to change without
prior notice to improve the performance.
The contents of this manual are subject to change without notice to improve quality.
© Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Trademarks other than that of Samsung Electronics are owned by their respective owners.
An administration fee may be charged in the following situations:
(a) An engineer is called out at your request, but it is found that the product has no defect (i.e., where
the user manual has not been read).
(b) You bring the unit to a repair centre, but it is found that the product has no defect (i.e., where the
user manual has not been read).
You will be informed of the administration fee amount before a technician visits.
Table of contents
Before Using the Product
Connecting and Using a Source Device
Securing the Installation Space
4
Read below before installing the product.
24
Safety Precautions
Cleaning
Electricity and Safety
Installation
Operation
4
5
5
6
7
Connecting and Using a PC
Connection Using the HDMI Cable
Connection Using the MINI DP Cable
Connecting the Power
24
24
25
25
Correct posture to use the product
26
Driver Installation
26
Setting Optimum Resolution
26
Preparations
Parts
10
Control Panel
10
Direct Key Guide
11
Function Key Guide
12
Configuring Eye Saver Mode, Brightness and Contrast
from Direct Key Guide
13
Types of Ports
14
Upgrading the Software via USB
15
Adjusting the Product Tilt and Height
17
Precautions for moving the product
18
Precautions for installation and use
Installing the stand on a table
19
20
Installation
Attaching the Stand
Removing the Stand
Tidying Up the Connected Cables
21
21
22
23
Screen Setup
SAMSUNG MAGIC Bright
27
Brightness
28
Contrast
28
Sharpness
28
Color
28
SAMSUNG MAGIC Upscale
29
HDMI Black Level
29
Eye Saver Mode
29
Game Mode
29
Response Time
29
Picture Size
30
Screen Adjustment
30
Configuring the PIP/PBP Settings
PIP/PBP Mode
31
Size
32
Position
32
Picture Size
32
Contrast
33
Adjusting OSD (On Screen
Display) settings
Transparency
34
Position
H-Position
V-Position
34
34
34
Language
34
Display Time
34
2
Table of contents
Setup and Reset
Installing the Software
Easy Setting Box
Restrictions and Problems with the Installation
Upgrade by downloading the firmware from the
website
System Requirements
Specifications
Self Diagnosis
35
41
41
DisplayPort Ver.
37
HDMI Mode
37
Eco Saving Plus
37
Off Timer Plus
38
PC/AV Mode
38
Troubleshooting Guide
Source Detection
38
Key Repeat Time
39
Power LED On
39
Reset All
39
Requirements Before Contacting Samsung Customer
Service Centre
42
Product diagnosis (Screen issue)
42
Checking the Resolution and Frequency
42
Check the following.
42
General
45
Standard Signal Mode Table
46
41
41
Appendix
Q&A
Responsibility for the Pay Service (Cost to
Customers)
Not a product defect
A Product damage caused by customer's fault
Others
51
51
51
51
44
Information
Information
40
3
Chapter 01
Before Using the Product
Securing the Installation Space
Safety Precautions
Make sure to have enough space for ventilation when placing the product. An internal temperature rise
may cause fire and damage the product. Maintain enough space around the product as shown in the
diagram when installing the product.
――The exterior may differ depending on the product.
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are
not followed.
CAUTION
10 cm
10 cm
10 cm
10 cm
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THERE
ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that high
voltage is present inside. It is
dangerous to make any kind of
contact with any internal part of this
product.
AC voltage: Rated voltage marked
with this symbol is AC voltage.
This symbol indicates that this
product has included important
literature concerning operation and
maintenance.
DC voltage: Rated voltage marked
with this symbol is DC voltage.
Class II product: This symbol indicates
that a safety connection to electrical
earth (ground) is not required. If this
symbol is not present on a product
with a mains lead, the product
MUST have a reliable connection to
protective earth (ground).
Caution. Consult instructions for use:
This symbol instructs the user to
consult the user manual for further
safety related information.
4
Cleaning
Electricity and Safety
High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used
nearby.
Warning
――Contact your nearest Samsung Customer Service Centre if you want to clean the inside of the product
•• Do not use a damaged power cord or plug, or a loose power socket.
(Service fee will be charged.)
Do not press the product screen with hands or other objects. There is a risk of damaging the screen.
――Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
――Take the following steps when cleaning.
1 Power off the product and PC.
2 Disconnect the power cord from the product.
――Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric
shock may result.
3 Wipe the product with a clean, soft and dry cloth.
‒‒ Do not apply a cleaning agent that contains alcohol, solvent, or surfactant to the product.
‒‒ Do not spray water or detergent directly on the product.
4 Wet a soft cloth in water, wing it out well, and then use the cloth to wipe the exterior of the product
clean.
5 Connect the power cord to the product when cleaning is finished.
6 Power on the product and PC.
•• Do not use multiple products with a single power socket.
•• Do not touch the power plug with wet hands.
•• Insert the power plug all the way in so it is not loose.
•• Connect the power plug to a grounded power socket (type 1 insulated devices only).
•• Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy
object.
•• Do not place the power cord or product near heat sources.
•• Clean any dust around the pins of the power plug or the power socket with a dry cloth.
Caution
•• Do not disconnect the power cord while the product is being used.
•• Only use the power cord provided with your product by Samsung. Do not use the power cord with
other products.
•• Keep the power socket where the power cord is connected unobstructed.
‒‒ The power cord must be disconnected to cut off power to the product when an issue occurs.
•• Hold the plug when disconnecting the power cord from the power socket.
5
Installation
Warning
Caution
•• DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT
INSTALL THE PRODUCT NEAR HEAT SOURCES.
•• Do not drop the product while moving.
•• Keep the plastic packaging out of the reach of children.
‒‒ Children may suffocate.
•• Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)
‒‒ The product may fall and become damaged and/or cause an injury.
‒‒ Using the product in an area with excess vibration may damage the product or cause a fire.
•• Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or
smoke.
•• Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
‒‒ The product lifespan may be reduced or a fire may result.
•• Do not install the product within the reach of young children.
‒‒ The product may fall and injure children.
•• Do not set down the product on its front.
•• When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of
the product is not protruding.
‒‒ The product may fall and become damaged and/or cause an injury.
‒‒ Install the product only on cabinets or shelves of the right size.
•• Set down the product gently.
‒‒ Product failure or personal injury may result.
•• Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical
substances, extreme temperatures or a significant presence of moisture, or a place where
the product will operate continuously for an extended period of time) may seriously affect its
performance.
‒‒ Be sure to consult Samsung Customer Service Centre if you want to install the product at such a
place.
•• Edible oil (such as soybean oil) may damage or distort the product. Keep the product away from oil
pollution. And do not install or use the product in the kitchen or near the kitchen stove.
6
Operation
Warning
•• There is a high voltage inside the product. Never disassemble, repair or modify the product
yourself.
‒‒ Contact Samsung Customer Service Centre for repairs.
•• To move the product, first disconnect all the cables from it, including the power cable.
•• If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord
immediately and contact Samsung Customer Service Centre.
•• Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper,
matches, etc) into the product (via the vent or input/output ports, etc).
‒‒ Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Centre.
•• Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the
product.
‒‒ Be sure to power off the product and disconnect the power cord when water or other foreign
substances have entered the product. Then contact Samsung Customer Service Centre.
•• Do not let children hang from the product or climb on top of it.
‒‒ Children may become injured or seriously harmed.
•• If the product is dropped or the outer case is damaged, turn off the power and disconnect the
power cord. Then contact Samsung Customer Service Centre.
‒‒ Continued use can result in a fire or electric shock.
•• Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
‒‒ The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a
serious injury.
•• During a lightning or thunderstorm, power off the product and remove the power cable.
•• Do not drop objects on the product or apply impact.
•• Do not move the product by pulling the power cord or any cable.
•• If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area
immediately.
•• Do not lift or move the product by pulling the power cord or any cable.
•• Do not use or keep combustible spray or an inflammable substance near the product.
•• Ensure the vents are not blocked by tablecloths or curtains.
‒‒ An increased internal temperature may cause a fire.
7
Caution
•• Leaving the screen fixed on a stationary image for an extended period of time may cause
afterimage burn-in or defective pixels.
‒‒ Set the screen to power-saving mode or moving-picture screen saver when not using the
product for an extended period of time.
•• Disconnect the power cord from the power socket if you do not plan on using the product for an
extended period of time (vacation, etc).
‒‒ Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.
•• Use the product at the recommended resolution and frequency.
‒‒ Your eyesight may deteriorate.
•• Insert the power plug into the AC/DC adapter until a click sound is heard.
•• Do not insert only the power plug into the power outlet.
•• Do not use an AC/DC adapter other than the provided one.
‒‒ It may cause electric shock or fire.
•• Do not insert the AC/DC adapter into the power outlet on the ceiling.
‒‒ It may cause electric shock or fire.
•• Rotate the power plug not to exceed the range (0 to 90°) on the AC/DC adapter.
‒‒ It may cause electric shock or fire.
•• Do not put AC/DC adapters together.
•• Never diassemble the power plug after being assembled. (It cannot be separated after assembly.)
•• Remove the plastic bag from the AC/DC adapter before you use it.
•• Never use the provided power plug for other devices.
•• Do not let water enter the AC/DC adapter device or get the device wet.
•• When removing the AC/DC adapter from the power outlet, hold the body of AC/DC adapter and pull
it up.
‒‒ An electric shock or fire may result.
‒‒ Avoid using the product outdoors where it can be exposed to rain or snow.
‒‒ Be careful not to get the AC/DC adapter wet when you wash the floor.
•• Do not put the AC/DC adapter near to any heating apparatus.
‒‒ Otherwise, a fire may result.
•• Keep the AC/DC adapter in a well-ventilated area.
‒‒ It may cause electric shock or fire.
•• Do not drop any objects or apply shock on the AC/DC adapter.
‒‒ It may cause electric shock or fire.
•• Use the AC/DC adapter after removing its plastic cover.
‒‒ Otherwise, this may result fire.
•• If you place the AC/DC power adapter hanging with the cord input facing upwards, water or other
foreign substances could enter the Adapter and cause the Adapter to malfunction.
Make sure to rest the AC/DC power adapter flat on a table or the floor.
8
•• Do not hold the product upside-down or move it by holding the stand.
‒‒ The product may fall and become damaged or cause an injury.
•• Looking at the screen too close for an extended period of time can deteriorate your eyesight.
•• Do not use humidifiers or stoves around the product.
•• Rest your eyes for more than 5 minutes or look at distance objects for every 1 hour of product use.
•• Do not touch the screen when the product has been turned on for an extended period of time as it
will become hot.
•• Store small accessories out of the reach of children.
•• Exercise caution when adjusting the product angle or stand height.
‒‒ Your hand or finger may get stuck and injured.
‒‒ Tilting the product at an excessive angle may cause the product to fall and an injury may result.
•• Do not place heavy objects on the product.
‒‒ Product failure or personal injury may result.
9
Chapter 02
Preparations
Parts
Parts
Description
JOG Button
Multi directional button that helps navigate.
――The JOG button is located on the rear left side of the product. The
button can be used to move up, down, left or right, or as Enter.
Control Panel
This LED is power status indicator and works as
――The colour and shape of parts may differ from what is shown. Specifications are subject to change without
•• Power On (Power button): Power LED Off
notice to improve quality.
•• Power saving mode: Power LED Blinking
JOG Button
Power LED
UP
(System → Power LED On) Actual models because of functional
variation maybe haven’t this function.
――The
power button is located on the left of the rear and used to turn
RIGHT
LEFT
PRESS(ENTER)
DOWN
Function Key Guide
•• Power Off (Power button): Power LED On
――The Power LED operation can be swapped by changing in the menu.
on or off the product.
Power LED
Function Key Guide
Press the JOG button when the screen is turned on. The Function Key
Guide will appear. To access the onscreen menu when the guide is
displayed, press the corresponding direction button again.
――Function Key Guide may vary depending on the function or product
model. Please refer to the actual product.
Return
10
Direct Key Guide
――On the Direct Key Guide screen, the following menu options appear when the product screen is switched on or the input source is changed.
Eye Saver Mode
Features
Eye Saver ModeOff
•• UP/DOWN: Adjust Brightness, Contrast, Eye Saver Mode.
•• PRESS(ENTER): Display Function Key Guide.
11
Function Key Guide
――To use the Function Key Guide, press the JOG button. Then the following window appears.
UP/DOWN/LEFT/RIGHT: Move to the item you want. The description for each item will appear when the focus changes.
PRESS(ENTER): The selected item will be applied.
Return
Parts
Source
Description
Selects
to change the input source by moving the JOG button in the Function Key Guide screen. A message will appear on the top left corner of the screen if the input source has
been changed.
Selects
by moving the JOG button in the Function Key Guide screen.
This product shows the menu as an on-screen display.
Menu
On screen display menu lock: Lock the on screen display menu to maintain the current settings or prevent other users from changing settings.
Enable/Disable: To enable or disable the on screen display menu lock, display the “Menu” screen, move the jog button to the right to go to the next stage, and then press and hold the
button to the left for 10 seconds.
――If the on screen display menu lock is enabled, Brightness and Contrast can be adjusted. The PIP/PBP function can also be used.
Eye Saver Mode is available. Information can be viewed.
PIP/PBP
Power Off
Return
Selects
by moving the JOG button in the Function Key Guide screen.
And then press the JOG button when configuring settings for the PIP/PBP function is required.
Selects
to turn the product off by moving the JOG button in the Function Key Guide screen.
Return to the previous menu by using the JOG button to select the
icon when the Function Key Guide screen is displayed.
――Actual models because of functional variation, Function Key Guide options will be different.
12
When the product displays nothing (i.e. Power saving mode or Non-signal mode), 2 direct keys for
control source and power could be used as below.
JOG Button
Power saving/Non-signal mode
UP
Source Change
Configuring Eye Saver Mode, Brightness and Contrast
from Direct Key Guide
Adjust the Brightness, Contrast and Eye Saver Mode by moving the JOG button.
Down
PRESS(ENTER) for 2 seconds
Contrast
Power Off
Off
Eye Saver Mode
Brightness
When the product displays the menu the JOG Button could be used as below.
JOG Button
Action
UP/DOWN
Move the option
Exit the menu.
LEFT
Close Sublist without saving value.
Value decreases in the slider.
RIGHT
PRESS(ENTER)
――The displayed image may differ depending on the model.
――The default brightness can vary depending on the region.
Brightness
――This menu is not available when SAMSUNG Bright is set to Dynamic Contrast mode.
MAGIC
――This menu is not available when Eco Saving Plus is enabled.
――This menu is not available when Eye Saver Mode is enabled.
Move to sublist.
Contrast
Value increases in the slider.
――This menu is not available when SAMSUNG Bright is in Cinema or Dynamic Contrast mode.
Save the value and close Sublist.
――This menu is not available when Game Mode is enabled.
MAGIC
――This menu is not available when PIP/PBP Mode is set to On and the Size is set to
(PBP Mode).
13
Types of Ports
Port
――The functions available may vary depending on the product model. The colour and shape of parts may
differ from what is shown. Specifications are subject to change without notice to improve quality. Refer to
the actual product.
SERVICE
Use a USB memory stick to perform software upgrade.
SERVICE
MINI
MINI
DP IN
DP IN
Connects to a PC using a MINI DP cable.
――S27R75*: MINI DP IN support 2560 x 1440 @ 144 Hz
――S32R75*: MINI DP IN support 3840 x 2160 @ 60 Hz
Connects to a source device using an HDMI cable.
HDMI
――S27R75*: HDMI IN support 2560 x 1440 @ 144 Hz
IN
DC
MINI
DP IN
Description
DC
19V
――S32R75*: HDMI IN support 3840 x 2160 @ 60 Hz
Connects to the AC/DC adapter.
19V
HDMI
IN
DC
19V
14
Upgrading the Software via USB
1 Connect a USB memory to the SERVICE port shown in the figure.
2 When the message as shown in the following figure is displayed on the product, select Yes to
upgrade the software.
Do you want to update via USB?
SERVICE
Yes
No
3 When the screen as shown in the following figure is displayed, select Yes.
MINI
DP IN
Update now
HDMI
IN
Update from version XXXX.X to version XXXX.X?
DC
19V
When the screen is on, press the jog button to display the Function Key Guide. When the Function
Key Guide are displayed, press and hold the jog button down for approximately 5 seconds.
Yes
No
4 The software upgrading proceeds.
Update now
Updating product Software…
Your product will turn itself off and on again automatically
after completing update.
0%
Power Off
15
Note
1 To perform software upgrade by using a USB memory, first format the USB memory to FAT32.
2 When performing upgrade, make sure that only one BIN file (.bin) is saved in the root directory.
3 To upgrade the software for the SR75 model, make sure the upgrade files are .bin formats. The file
name should follow the naming conventions for the SR75 model (e.g. M-R75**SGAA-****.*[fourdigit number].bin). The ** is the screen size in inches, the ****.* is the version number, and the
four-digit number is the checksum. For example, “M-R7532SGAA-0800.0[D06E].bin” conforms to
the naming conventions for the SR75 32" model and should be copied to the root directory.
4 If the No valid update files found. Please check your USB device and try again. message is
displayed, this is probably due to the following reasons.
Update now
No valid update files found.
Please check your USB device and try again.
OK
Cancel
‒‒ A USB memory is not connected to the SERVICE port.
‒‒ The files in the connected USB memory are not compatible formats.
‒‒ There are no valid upgrade files found in the connected USB memory. (There are no upgrade files
saved in the memory or the file names are incorrect.)
5 Do not turn off the product. And prevent the upgrading from any interruption as far as possible. In
general, the product returns to the previous version if an upgrade is interrupted.
16
Adjusting the Product Tilt and Height
Do not use or store the product with the screen facing down.
――The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
S27R75*
18 ~ 60˚
S32R75*
576.0 mm
602.9 mm
0 ~ 72˚
0 ~ 66˚
213.9 mm
184.7 mm
•• It is recommended that the product be tilted to an angle within the optimum range.
•• When installing the product close to a wall with excessive force, exercise caution so that your hand
is not caught between the product and the wall.
•• The rotation and height adjustment has a certain tolerance. Stay within the tolerances when
rotating or adjusting the height of the product.
331.6 mm
319.8 mm
•• Hold the sides of the product when adjusting the height.
Adequate operation range
20˚
-5˚
――Be careful not to apply excessive force to the screen when adjusting the product height.
When touched to the floor
S27R75*
S32R75*
10˚
16˚
66˚
72˚
-5˚
-5˚
17
Precautions for moving the product
•• Do not directly apply pressure on the screen.
•• Do not hold the screen when moving the
product.
•• Do not hold the product upside down only by
the stand.
•• Hold the lower corners or edges of the
product when moving it.
18
Precautions for installation and use
≤40 mm
30 ~ 65 mm
55 ~ 90 mm
•• If the product is set up close to a wall and you tilt the stand to
raise it up, the product may collide with the wall and become
damaged. Do not raise the product with excessive force.
•• Table thickness for installation: ≤40 mm, 30 ~ 65 mm, 55 ~ 90 mm
•• To install the product on a table, make sure the table is strong enough to bear the product weight.
Installing the product on a table made of glass or other fragile material may damage the product.
•• It is difficult to install the product on a table that has a raised edge. Exercise caution during
installation.
•• If the table top surface is uneven or inclined, the product may not be able to stand properly.
•• Installing the stand may cause an imprint of the stand to form on the table.
•• When lowering the product close to the floor, make sure you
hold the sides of the product. Do not lower the product with
excessive force. There is a risk of damage to your hands.
――Do not install the product on an angled part of the table.
――When adjusting the product height, do not put your hand near the region where the stand is folded.
――If you set the product to an incompatible resolution, screen flickering may occur. Change to a supported
resolution by referring to the Standard Signal Mode Table.
•• Do not put any object under the product. There is a risk of
damage to the object when lowering the product close to the
floor.
19
Installing the stand on a table
Table requirements for installing the stand are shown below by table type.
•• Table with no raised edge
≤90 mm
≤40 mm
•• Table with a raised edge (
The stand can be installed if a 90 mm space is
available between the spot 15 mm away from
one end of the table and the other end or if the
distance to the raised edge is more than 95
mm.
•• The stand can be used through adjustment
depending on the table thickness. (≤90 mm)
30 ~ 65 mm
55 ~ 90 mm
)
15 mm ≥75 mm
≥95 mm
•• Table with a spaced partition
•• The stand can be installed if the gap between
the table and the partition is more than 15
mm.
――Tidy up the cables by running them in the
stand groove on the rear of the product before
installing the stand on the table. It is difficult to
tidy up cables if the gap between the table and
the partition is narrow. For details on how to tidy
up cables, refer to “Tidying Up the Connected
Cables.”
20
Installation
Attaching the Stand
――Before assembling the product, place the product down on a flat and stable surface so that the screen is
facing downwards.
――The exterior may differ depending on the product.
――The table should be relocated, depending on the space where the stand will be installed.
――Attach the stand to the product and tidy up the cables.
Caution
Do not press down on the product. There is a risk
of damaging the product.
1
Make sure the product front faces down, as shown
in the figure.
3
Attach and fix the stand to the rear of the product
by using the screws.
Attach the Cover-Clean Back Stand.
Before placing the product facing down to the
table, put a cushion on the table to protect the
product screen.
4
After attaching the stand to the product, tidy up
the cables.
――For details on how to tidy up cables, refer to “Tidying
Up the Connected Cables.”
5
6
Install the stand on the table, as shown in the
figure.
After installing the stand on the table, turn the
clamp to the right to engage the lock.
――Before installing the stand, adjust the handle to fit
――If you turn it to the left, the lock will be disengaged.
7
The stand is now completely assembled.
the table thickness for easier installation.
21
Removing the Stand
――Before removing the stand from the product, place the product on a flat and stable surface with the screen
facing down.
――The exterior may differ depending on the product.
――The table should be relocated, depending on the space where the stand will be installed.
Caution
Do not press down on the product. There is a risk
of damaging the product.
1
Turn the clamp on the stand, installed on the
table, to the left to disengage the lock.
2
Remove the stand from the table by holding the
stand and the bottom of the product.
3
Make sure the product front faces down, as shown
in the figure.
Before placing the product facing down to the
table, put a cushion on the table to protect the
product screen.
4
Remove the connected cables.
――If you turn it to the right, the lock will be engaged.
5
Remove the Cover-Clean Back Stand.
6
Remove the screws on the stand.
22
Tidying Up the Connected Cables
1
Connect the Y cables to the two ports, as shown in
the figure.
2
Tidy up the connected Y cable by aligning it with
the stand groove, as shown in the figure.
――Make sure the Y cable is tidied up at the left of the
groove.
――The MINI DP cable can be tidied up at the right
side.
3
Use the same method to tidy up other cables.
23
Chapter 03
Connecting and Using a Source Device
Read below before installing the product.
Connecting and Using a PC
1 Before installing the product, check the shapes of both ports of the supplied signal cables and the
Select a connection method suitable for your PC.
2 Before installing the product, make sure you remove the power cables from both the product and
――Provided ports may vary depending on the product.
3 After all signal cables have been properly connected, connect the power cables back to the product
Connection Using the HDMI Cable
shapes and locations of the ports on the product and external device.
――Connecting parts may differ in different products.
the external device to prevent damage to the product due to a short circuit or over current.
and the external device.
4 After installation is completed, make sure you read the user guide to acquaint yourself with the
product functions, precautions and other information required to use the product properly.
First make sure that the power cables for product and other devices (e.g. PC, settop box, etc.)
are removed.
HDMI IN
――S27R75*: To display 2560 x 1440 @ 144 Hz, use an HDMI cable that supports 2560 x 1440 @ 144 Hz to
connect HDMI IN. Make sure that the graphics card of the HDMI source supports 2560 x 1440 @ 144 Hz.
――S32R75*: To display 3840 x 2160 @ 60 Hz, use an HDMI cable that supports 3840 x 2160 @ 60 Hz to connect
HDMI IN. Make sure that the graphics card of the HDMI source supports 3840 x 2160 @ 60 Hz.
――When connecting an HDMI cable, use the cable that came with the components of the product. If you use
an HDMI cable other than provided by Samsung, the image quality may be degraded.
24
Connection Using the MINI DP Cable
First make sure that the power cables for product and other devices (e.g. PC, settop box, etc.)
are removed.
Connecting the Power
1
MINI DP IN
2
4
5
――S27R75*: To display 2560 x 1440 @ 144 Hz, use a MINI DP cable that supports 2560 x 1440 @ 144 Hz. Make
sure that the graphics card of the MINI DP source supports 2560 x 1440 @ 144 Hz.
――S32R75*: To display 3840 x 2160 @ 60 Hz, use a MINI DP cable that supports 3840 x 2160 @ 60 Hz. Make
sure that the graphics card of the MINI DP source supports 3840 x 2160 @ 60 Hz.
3
1 Connect the power plug to the AC/DC adapter.
Do not remove the power plug after assembly.
2 Connect the power cable of the Y cable to the DC 19V port on the rear of the product.
3 Connect the power cable of the power adapter, connected to the power plug, to the Y cable which
has been tidied up.
4 Plug the AC/DC adapter into the power outlet.
5 Press the JOG button on the back of the product to turn it on.
――The input voltage is switched automatically.
――In some areas, installation of an additional power plug is not necessary.
25
Correct posture to use the product
Driver Installation
――You can set the optimum resolution and frequency for this product by installing the corresponding drivers.
――To install the latest version of the product driver, download it from the Samsung Electronics website at
http://www.samsung.com.
Setting Optimum Resolution
An information message about setting optimum resolution will appear if you power on the product for
the first time after purchase.
Use the product in the correct posture as follows:
•• Straighten your back.
•• Allow a distance of 45 to 50cm between your eye and the screen, and look slightly downward at
the screen.
•• Keep your eyes directly in front of the screen.
Select a language on information message and change the resolution on your PC to the optimum
setting.
――If the optimum resolution is not selected, the message will appear up to three times for a specified time
even when the product is turned off and on again.
――If you want to set the optimum resolution for your computer. Please refer to (Q&A) → “How can I change the
resolution?”
•• Adjust the angle so light does not reflect on the screen.
•• Keep your forearms perpendicular to your upper arms and level with the back of your hands.
•• Keep your elbows at about a right angle.
•• Adjust the height of the product so you can keep your knees bent at 90 degrees or more, your heels
attached to the floor, and your arms lower than your heart.
•• Do the Eye excercises or blink frequently, then eye fatigue will be relieved.
26
Chapter 04
Screen Setup
Function Key Guide →
→ Picture
Configure the screen settings such as brightness. A detailed description of each function is provided. Refer to your product for details.
――The functions available may vary depending on the product model. The colour and shape of parts may
differ from what is shown. Specifications are subject to change without notice to improve quality.
In PC mode
•• Custom: Customise the contrast and brightness as required.
•• Standard: Obtain a picture quality suitable for editing documents or using Internet.
SAMSUNG MAGIC Bright
•• Cinema: Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD content.
This menu provides an optimum picture quality suitable for the environment where the product will be
used.
In AV mode
――This menu is not available when Eco Saving Plus is enabled.
――This menu is not available when Game Mode is enabled.
――This menu is not available when Eye Saver Mode is enabled.
――Not available when PIP/PBP Mode is set to On.
•• Dynamic Contrast: Obtain balanced brightness through automatic contrast adjustment.
SAMSUNG
When the external input is connected through HDMI/MINI DP and PC/AV Mode is set to AV, MAGIC
Bright has four automatic picture settings (Dynamic, Standard, Movie and Custom) that are preset at
the factory. You can activate either Dynamic, Standard, Movie or Custom. You can select Custom which
automatically recalls your personalised picture settings.
•• Dynamic: Select this mode to view a sharper image than in Standard mode.
•• Standard: Select this mode when the surroundings are bright.
•• Movie: Select this mode when the surroundings are dark. This will save power and reduce eye
fatigue.
•• Custom: Select this mode when you want to adjust the image according to your preferences.
27
Brightness
Color
You can adjust the general brightness of the picture. (Range: 0~100)
Adjust the tint of the screen.
A higher value will make the picture appear brighter.
――This menu is not available when SAMSUNG Bright is set to Cinema or Dynamic Contrast mode.
――This menu is not available when SAMSUNG Bright is set to Dynamic Contrast mode.
――This menu is not available when Game Mode is enabled.
――This menu is not available when Eco Saving Plus is enabled.
――This menu is not available when Eye Saver Mode is enabled.
――This menu is not available when Eye Saver Mode is enabled.
――Not available when PIP/PBP Mode is set to On.
MAGIC
MAGIC
•• Red: Adjust the red saturation level. Values closer to 100 mean greater intensity for the colour.
•• Green: Adjust the green saturation level. Values closer to 100 mean greater intensity for the colour.
Contrast
•• Blue: Adjust the blue saturation level. Values closer to 100 mean greater intensity for the colour.
•• Color Tone: Select a colour tone that best suits your viewing needs.
Adjust the contrast between the objects and background. (Range: 0~100)
‒‒ Cool 2: Set the colour temperature to be cooler than Cool 1.
A higher value will increase the contrast to make the object appear clearer.
‒‒ Cool 1: Set the colour temperature to be cooler than Normal mode.
――This option is not available when SAMSUNG Bright is in Cinema or Dynamic Contrast mode.
MAGIC
――This menu is not available when Game Mode is enabled.
――This menu is not available when PIP/PBP Mode is set to On and the Size is set to
‒‒ Normal: Display the standard colour tone.
‒‒ Warm 1: Set the colour temperature to be warmer than Normal mode.
(PBP Mode).
‒‒ Warm 2: Set the colour temperature to be warmer than Warm 1.
‒‒ Custom: Customise the colour tone.
――When the external input is connected through HDMI/MINI DP and PC/AV Mode is set to AV, Color Tone
Sharpness
has four colour temperature settings (Cool, Normal, Warm and Custom).
•• Gamma: Adjust the middle level of luminance.
Make the outline of objects more clear or blurry. (Range: 0~100)
‒‒ Mode1 / Mode2 / Mode3
A higher value will make the outline of objects clearer.
――This option is not available when SAMSUNG Bright is in Cinema or Dynamic Contrast mode.
MAGIC
――This menu is not available when Game Mode is enabled.
――Not available when PIP/PBP Mode is set to On.
28
SAMSUNG MAGIC Upscale
Eye Saver Mode
MAGICUpscale function
Set to an optimum picture quality suitable for eye relaxation.
SAMSUNG
can enhance the layers of the picture details and the vividness of the picture.
The function has more obvious effects on low-resolution pictures.
――This menu is not available when SAMSUNG Bright is set to Cinema or Dynamic Contrast mode.
MAGIC
――This menu is not available when Game Mode is enabled.
•• Off / Mode1 / Mode2
――Comparing with Mode1, Mode2 has a stronger effect.
HDMI Black Level
TÜV Rheinland “Low Blue Light Content” is a certification for products which meet requirements for
lower blue light levels. When Eye Saver Mode is 'On', the blue light that wavelength is around 400nm
will decrease, and it will provide an optimum picture quality suitable for eye relaxation. At the same
time, the blue light level is lower than in the default settings, and it was tested by TÜV Rheinland and
certified as it met the requirements of TÜV Rheinland “Low Blue Light Content” standards.
Game Mode
Configure the product screen settings for game mode.
If a DVD player or set-top box is connected to the product via HDMI, image quality degradation (contrast/
colour degradation, black level, etc.) may occur, depending on the connected source device.
Use this feature when playing games on a PC or when a game console such as PlayStation™ or Xbox™
is connected.
In such case, HDMI Black Level can be used to adjust the image quality.
――This menu is not available when Eye Saver Mode is enabled.
――When the product turns off, enters power-saving mode or changes input sources, Game Mode turns Off
――This function is only available in HDMI mode.
――Not available when PIP/PBP Mode is set to On.
•• Normal: Select this mode when there is no contrast ratio degradation.
•• Low: Select this mode to reduce the black level and increase the white level when there is a
contrast ratio degradation.
――HDMI Black Level may not be compatible with some source devices.
――The HDMI Black Level feature is only activated at a certain AV resolution, such as 720P @ 60 Hz and 1080P
@ 60 Hz.
even if it is set to On.
――If you want to keep Game Mode enabled all the time, select Always On.
――Not available when PIP/PBP Mode is set to On.
Response Time
Accelerate the panel response rate to make video appear more vivid and natural.
――Use Standard mode when not playing a video or game.
――S27R75*: This menu is not available when PIP/PBP Mode is set to On and the Size is set to
/
(PIP
――S32R75*: This menu is not available when PIP/PBP Mode is set to On and the Size is set to
/
/
Mode).
(PIP Mode).
29
Picture Size
Screen Adjustment
Change the picture size.
――This option is only available when PC/AV Mode is set to AV.
――This menu is not available when PIP/PBP Mode is set to On and the Size is set to
(PBP Mode).
In PC mode
•• Auto: Display the picture according to the aspect ratio of the input source.
•• Wide: Display the picture in full screen regardless of the aspect ratio of the input source.
In AV mode
――This menu is only available when Picture Size is set to Screen Fit in AV Mode.
When a 480P or 576P or 720P or 1080P signal is input in AV mode and the product can display normally,
select Screen Fit to adjust horizontal position and vertical position in 0-6 levels.
Configuring H-Position & V-Position
H-Position: Move the screen to the left or right.
V-Position: Move the screen up or down.
•• 4:3: Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.
•• 16:9: Display the picture with an aspect ratio of 16:9.
•• Screen Fit: Display the picture with the original aspect ratio without cutting off.
――The function may not be supported depending on the ports provided with the product.
――Changing the Picture Size is available when the following conditions are satisfied.
――The input source is 480p, 576p, 720p, or 1080p and product can display normally (Not every model can
support all of these signals.).
――This can only be set when the external input is connected through HDMI/MINI DP and PC/AV Mode is set
to AV.
30
Chapter 05
Configuring the PIP/PBP Settings
Function Key Guide →
→ PIP/PBP
A detailed description of each function is provided. Refer to your product for details.
――The functions available may vary depending on the product model. The colour and shape of parts may
differ from what is shown. Specifications are subject to change without notice to improve quality.
PIP/PBP Mode
Enable or disable the PIP/PBP Mode function.
The PIP (Picture in Picture) function separates the screen into two parts. One source device is displayed
on the main screen at the same time the another source device is displayed in inset windows.
The PBP (Picture by Picture) function separates the screen in half displaying output from two different
source devices simultaneously on the left and right sides of the screen.
――PIP/PBP mode is compatible with Windows 7, Windows 8, and Windows 10.
――The PIP/PBP function may not be available depending on the specifications of the graphics card used. If the
screen is blank in PIP/PBP mode when the optimum resolution is selected, go to Control Panel → Display →
Screen Resolution and click Detect on the PC. (Instructions are based on Windows 7.) If the screen is blank
when the resolution is set to the optimum resolution, change the resolution to 1280 x 1024.
――The screen may flicker briefly or appear after a delay when you enable or disable the PIP/PBP function or
when you change the screen size with the PIP/PBP function activated. This can typically arise when a PC
and a product are connected to two or more input sources. It has nothing to do with the performance of
a product. The issue is mainly caused when the video signals are delayed in transmission to the product
depending on the graphics card performance.
――S27R75*: To obtain optimum picture quality, it is recommended that a graphics card or DVD that supports
the QHD (2560 x 1440 @ 144 Hz) resolution be connected to the HDMI IN port.
To obtain optimum picture quality, it is recommended that a graphics card or DVD that supports the QHD
(2560 x 1440 @ 144 Hz) resolution be connected to the MINI DP IN port.
――S32R75*: To obtain optimum picture quality, it is recommended that a graphics card or DVD that supports
the 4K (3840 x 2160 @ 60 Hz) resolution be connected to either the HDMI IN or MINI DP IN port.
――When the PIP/PBP function is enabled, the resolution will not be able to automatically switch to the
optimum resolution due to a compatibility issue between the graphics card and the Windows system.
Set PIP/PBP Mode to Off. Alternatively, restart the product, then set the resolution to the optimum setting
using the Windows interface.
――If the product is set to an incompatible resolution, the product may display an abnormal or blank screen.
Change to a supported resolution by referring to the Standard Signal Mode Table.
31
Size
Picture Size
Select the size and aspect ratio of the sub-screen.
Select the image size for each screen.
•• S27R75*:
/
/
•• S32R75*:
/
/
/
•• Auto: Display the picture according to the aspect ratio of the each screen input source.
Select the position of the sub-screen from the available options.
/
/
))
In PC mode
Position
••
PBP Mode (available in PBP mode(Size
/
――Not available when PBP is selected.
――The screen may flicker if the input source is unstable.
•• Wide: Display the picture in full screen regardless of the aspect ratio of the each screen input
source.
In AV mode
•• 4:3: Display the picture of the sub-screen with an aspect ratio of 4:3. Suitable for videos and
standard broadcasts.
•• 16:9: Display the picture of the sub-screen with an aspect ratio of 16:9.
•• Screen Fit: Display the picture of the sub-screen with the original aspect ratio without cutting
anything off.
――The function may not be supported depending on the ports provided with the product.
――Changing the screen size is available when the following conditions are satisfied.
――The input source is 480p, 576p, 720p, or 1080p and product can display normally (Not every model can
support all of these signals.).
――This can only be set when the external input is connected through HDMI/MINI DP and PC/AV Mode is set
to AV.
32
PIP Mode (available in PIP mode (Size
•• S27R75*:
/
•• S32R75*:
/
/
/
))
Contrast
/
In PC mode
•• Auto: Display the picture according to the aspect ratio of the each screen input source.
•• Wide: Display the picture in full screen regardless of the aspect ratio of the each screen input
source.
In AV mode
PBP Mode (available in PBP mode(Size
))
Adjust the contrast level for each screen.
PIP Mode (available in PIP mode(Size
/
/
))
Adjust the contrast level for sub-screen.
•• 4:3: Display the picture of the sub-screen with an aspect ratio of 4:3. Suitable for videos and
standard broadcasts.
•• 16:9: Display the picture of the sub-screen with an aspect ratio of 16:9.
•• Screen Fit: Display the picture of the sub-screen with the original aspect ratio without cutting
anything off.
――The function may not be supported depending on the ports provided with the product.
――Changing the screen size is available when the following conditions are satisfied.
――The input source is 480p, 576p, 720p, or 1080p and product can display normally (Not every model can
support all of these signals.).
――This can only be set when the external input is connected through HDMI/MINI DP and PC/AV Mode is set
to AV.
33
Chapter 06
Adjusting OSD (On Screen Display) settings
Function Key Guide →
→ On Screen Display
A detailed description of each function is provided. Refer to your product for details.
――The functions available may vary depending on the product model. The colour and shape of parts may
differ from what is shown. Specifications are subject to change without notice to improve quality.
Transparency
Set the transparency for the menu windows.
Position
H-Position
Move the menu position to the left or right.
V-Position
Move the menu position up or down.
Language
Set the menu language.
――A change to the language setting will only be applied to the onscreen menu display.
――It will not be applied to other functions on your PC.
Display Time
The OSD menu will automatically disappear if the menu is not used for a specified period of time.
Display Time is a function to specify the time which you want the OSD menu to disappear.
34
Chapter 07
Setup and Reset
Function Key Guide →
→ System
A detailed description of each function is provided. Refer to your product for details.
――The functions available may vary depending on the product model. The colour and shape of parts may
differ from what is shown. Specifications are subject to change without notice to improve quality.
2 Select OK when the following screen is prompted.
The test photo will now be shown. Look carefully at the screen for the next 5 seconds.
Self Diagnosis
1 Use the Function Key Guide and go to
OK
→ System → Self Diagnosis.
System
Self Diagnosis
DisplayPort Ver.
1.2↑
HDMI Mode
2.0
Eco Saving Plus
Off
••
Review the test screen.
Perform this
test when you
experience a
problem with your
monitor's picture.
Off Timer Plus
PC/AV Mode
Source Detection
Auto
Return
35
3 Base on the test result, select Yes / No / Show Again.
Do you still see the problem in this test photo?
If you need to see the photo again, click Show Again.
Yes
••
No
Show Again
You will see the following screen when you select Yes.
Self Diagnosis Complete
Contact the Samsung Call Center for assistance.
Please have the following information ready:
‐‐ Model Code: **************
‐‐ Software Version: *-*********-****.*
‐‐ S/N: **************
OK
••
You will see the following screen when you select No.
Self Diagnosis Complete
If there are no issues with the test photo, it means that your monitor is working properly. To find
the problem, follow the troubleshooting steps below:
‐‐ Turn off the monitor, PC, and all other connected devices. Turn the monitor back on first, then
the PC and other devices.
‐‐ Update the operating system and graphics card driver to the latest version and restart your PC.
‐‐ Connect the monitor to another port of your PC or connected device.
‐‐ Reset the settings in 'System→Reset All'
It is recommended that you use the cable provided at purchase.
OK
36
DisplayPort Ver.
Eco Saving Plus
Select the DisplayPort version to use.
Reduce energy consumption compared to consumption at the maximum brightness level.
――Incorrect settings may cause the screen to go blank. If this occurs, check the device specifications.
――This option is not available when SAMSUNG Bright is in Dynamic Contrast mode.
――If the product (when set to DisplayPort) is displaying the message Check the cable connection and the
――This menu is not available when Game Mode is enabled.
settings of the source device. press the JOG button to display the function-button screen and then select
→ System → DisplayPort Ver. → 1.1 or 1.2↑.
HDMI Mode
MAGIC
――This menu is not available when Eye Saver Mode is enabled.
――Not available when PIP/PBP Mode is set to On.
••
Off: Deactivate the Eco Saving Plus function.
••
Auto: The power consumption will automatically be reduced by about 10% over the current setting.
(The reduction of power consumption depends on the customer screen brightness condition.)
Select the HDMI mode to use.
――The supportable device and resolution may differ depending on its version.
••
Low: Saves up to 25 % energy compared to the maximum brightness.
••
High: Saves up to 50 % energy compared to the maximum brightness.
――When the version is changed, the screen may blink.
――If you set the HDMI Mode to 1.4, some high resolutions may not be supported because of bandwidth
limitation of the HDMI 1.4 protocol.
――When the setting is not appropriate, a blank screen may appear. In this case, check the specifications of the
device.
――This menu is not available when PIP/PBP Mode is set to On and the Size is set to
(PBP Mode).
37
Off Timer Plus
Configuring Off Timer
PC/AV Mode
Set PC/AV Mode to AV. The picture size will be enlarged.
This option is useful when you view a movie.
Off Timer: Turn on Off Timer mode.
••
Set to PC when connected to a PC.
Turn Off After: The off timer can be set within a range of 1 to 23 hours. The product will automatically
power off after the specified number of hours.
••
Set to AV when connected to an AV device.
――This option is only available when Off Timer is set to On.
――For products for the market in some regions, the Off Timer is set to automatically activate 4 hours after the
product powers on. This is done in accordance with power supply regulations. If you do not want the timer
to activate, go to
→ System → Off Timer Plus and set Off Timer to Off.
Configuring Eco Timer
Eco Timer: Turn on Eco Timer mode.
Eco Off After: The Eco Timer can be set between 10 and 180 minutes. The product will automatically
power off after the specified time has elapsed.
――This option is only available when Eco Timer is set to On.
――Products with a display area of 16:9 or 16:10 are only supported.
――If the product is in HDMI, DisplayPort mode and the screen says Check the cable connection and the
settings of the source device. press the JOG button to display the function-button screen and then select
→ System → PC/AV Mode → HDMI, DisplayPort → PC or AV.
Source Detection
Select either Auto or Manual as the method to recognise input source.
――Not available when PIP/PBP Mode is set to On.
38
Key Repeat Time
Control the response rate of a button when the button is pressed.
Acceleration, 1 sec, or 2 sec can be selected. If No Repeat is selected, a command responds only once
when a button is pressed.
Power LED On
Configure the settings to enable or disable the power LED located at the lower part of the product.
••
Working: The power LED is on when the product is turned on.
••
Stand-by: The power LED is on when the product is turned off.
Reset All
Return all the settings for the product to the default factory settings.
39
Chapter 08
Information
Function Key Guide →
→ Information
A detailed description of each function is provided. Refer to your product for details.
――The functions available may vary depending on the product model. The colour and shape of parts may
PIP
differ from what is shown. Specifications are subject to change without notice to improve quality.
Picture
PIP/PBP
Information
OnScreen Display
System
View the current input source mode, frequency and resolution that are in use and the current product
version.
Picture
Information
Information
Information
DisplayPort
Current Version: *-*********-***
PBP
Picture
OnScreen Display
Information
HDMI
**** x ****
**kHz **Hz
Exit
PIP/PBP
System
Information
Information
PIP/PBP
HDMI
**** x ****
**kHz **Hz
Current Version: *-*********-***
OnScreen Display
System
Information
Exit
――The displayed image may differ depending on the model.
HDMI
**** x ****
**kHz **Hz
DisplayPort
Current Version: *-*********-***
Exit
40
Chapter 09
Installing the Software
Easy Setting Box
System Requirements
OS
Hardware
•• Windows 7 32Bit/64Bit
•• At least 32MB of memory
•• Windows 8 32Bit/64Bit
•• At least 60MB of free space on the hard disk drive
Easy Setting Box enables users to use the product by partitioning multiple sections.
•• Windows 8.1 32Bit/64Bit
To install the latest version of Easy Setting Box, download it from the Samsung Electronics website at
http://www.samsung.com.
•• Windows 10 32Bit/64Bit
――The software may not work properly if you do not restart the PC after the installation.
――The Easy Setting Box icon may not appear depending on the PC system and the product specifications.
――If the shortcut icon does not appear, press the F5 key.
Restrictions and Problems with the Installation
The Easy Setting Box installation may be affected by the Graphics Card, Motherboard and the
Networking Environment.
Upgrade by downloading the firmware from the website
Visit the Samsung Electronics website at http://www.samsung.com, enter the product model and
download the firmware file.
――For details on how to upgrade, refer to the upgrade guidance file provided at the website.
41
Chapter 10
Troubleshooting Guide
Requirements Before Contacting Samsung
Customer Service Centre
――Before calling Samsung Customer Service Centre, test your product as follows. If the problem persists,
contact Samsung Customer Service Centre.
Check the following.
Installation issue
The screen keeps switching on and off.
Check the cable connection between the product and PC, and ensure the connectors are locked.
Product diagnosis (Screen issue)
If a problem occurs with the product screen, run Self Diagnosis to check that the product is working
properly.
Checking the Resolution and Frequency
If a resolution that is not supported (see the Standard Signal Mode Table) is selected, the Not Optimum
Mode message may appear for a short time or the screen may not be displayed properly.
――The displayed resolution may vary, depending on the PC system settings and cables.
Blank spaces are found on all four sides of the screen when an HDMI cable is connected to the
product and PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the
screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the
graphics card driver to the latest version.
(Please contact the graphics card or PC manufacturer for further details about how to adjust the
screen settings.)
The power plug cannot be removed from the power adapter.
Do not remove the power plug after assembly.
Screen issue
The power LED is off. The screen will not switch on.
Check that the power cable is connected properly.
If a problem occurs with the product screen, run Self Diagnosis to check that the product is working
properly.
42
The message Check the cable connection and the settings of the source device. appears.
There is no image on the screen and the power LED blinks every 0.5 to 1 second.
Check that the cable is properly connected to the product.
The product is operating in power-saving mode.
Check that the device connected to the product is powered on.
Press any key on the keyboard or move the mouse to return to normal operating mode.
If the product is in HDMI or DisplayPort mode, press the JOG button to display the function-button
Text is blurry.
screen and select the
If using a Windows OS (e.g. Windows 7, Windows 8, Windows 8.1 or Windows 10): Go to Control Panel →
Fonts → Adjust ClearType text and change Turn on ClearType.
icon.
Not Optimum Mode is displayed.
This message appears when the signal from the graphics card exceeds the maximum resolution or
frequency for the product.
Change the maximum resolution and frequency to suit the product performance, referring to
Standard Signal Mode Table (P.46).
Video playback is choppy.
Playback of high-definition large video files can be choppy. This may be because the video player is
not optimised for the PC resource.
Try playing the file on another video player.
The images on the screen look distorted.
Check the cable connection to the product.
The screen is not clear. The screen is blurry.
Remove any accessories (video extension cable, etc.) and try again.
Set the resolution and frequency to the recommended level.
The screen appears unstable and shaky. There are shadows or ghost images left on the screen.
Source device issue
A beeping sound is heard when my PC is booting.
If a beeping sound is heard when your PC is booting, have your PC serviced.
Check that the resolution and frequency for the PC are within the range of resolution and frequency
compatible with the product. Next, if required, change the settings, referring to Standard Signal
Mode Table (P.46) in this manual and the Information menu on the product.
The screen is too bright. The screen is too dark.
Adjust Brightness and Contrast.
Screen colour is inconsistent.
Change the Color settings.
The colours on the screen have a shadow and are distorted.
Change the Color settings.
White does not really look white.
Change the Color settings.
43
Q&A
――Refer to the user manual for your PC or graphics card for further instructions on adjustment.
How can I change the frequency?
Set the frequency on your graphics card.
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Screen Resolution → Advanced settings → Monitor, and adjust Screen Refresh Rate under Monitor settings.
•• Windows 8(Windows 8.1): Go to Settings → Control Panel → Appearance and Personalization → Display → Screen Resolution → Advanced settings → Monitor, and adjust Refresh rate under Monitor settings.
•• Windows 10: Go to Settings → System → Display → Advanced display settings → Display adapter properties → Monitor, and adjust Screen refresh rate under Monitor settings.
How can I change the resolution?
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Screen Resolution → Adjust Resolution.
•• Windows 8(Windows 8.1): Go to Settings → Control Panel → Appearance and Personalization → Display → Adjust Resolution, and adjust the resolution.
•• Windows 10: Go to Settings → System → Display → Advanced display settings, and adjust the resolution.
How do I set power-saving mode?
•• Windows 7: Go to Control Panel → Appearance and Personalization → Personalization → Screen Saver Settings → Power options or BIOS SETUP on the PC.
•• Windows 8(Windows 8.1): Go to Settings → Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings → Power options or BIOS SETUP on the PC.
•• Windows 10: Go to Settings → Personalization → Lock screen → Screen timeout settings → Power & sleep or BIOS SETUP on the PC.
44
Chapter 11
Specifications
General
Model Name
S27R75*
S32R75*
Size
27 Class (27 Inches / 68.4 cm)
32 Class (31.5 Inches / 80.0 cm)
Display area
596.736 mm (H) x 335.664 mm (V)
697.3 mm (H) x 392.2 mm (V)
Pixel Pitch
0.2331 mm (H) x 0.2331 mm (V)
0.06 mm (H) x 0.181 mm (V)
Maximum Pixel Clock
594 MHz (HDMI)
Power Supply
AC100-240V~ 50/60Hz
Based on the AC voltage of the adapter. For the DC voltage of the
product, refer to the product label.
Signal connectors
HDMI, MINI DisplayPort
Environmental conditions
Operating
――Plug-and-Play
This product can be installed and used with any Plug-and-Play compatible systems. Two-way data
exchange between the product and PC system optimises the product settings. Product installation takes
place automatically. However, you can customise the installation settings if desired.
――Panel Dots (Pixels)
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be
brighter or darker on the LCD panel. This does not affect product performance.
――The above specifications are subject to change without notice to improve quality.
――This device is a Class B digital apparatus.
――For detailed device specifications, visit the Samsung Electronics website.
Temperature: 10 °C – 40 °C (50 °F – 104 °F)
Humidity: 10 % – 80 %, non-condensing
Storage
Temperature: -20 °C – 45 °C (-4 °F – 113 °F)
Humidity: 5 % – 95 %, non-condensing
45
Standard Signal Mode Table
Model Name
S27R75*
Synchronization
Resolution
S32R75*
Horizontal Frequency
70.56 ~ 214.56 kHz
147.78 ~ 148.38 kHz
Vertical Frequency
48 ~ 144 Hz (DisplayPort / HDMI)
60 Hz (DisplayPort / HDMI)
2560 x 1440 @ 144 Hz (DisplayPort / HDMI)
3840 x 2160 @ 60 Hz (DisplayPort / HDMI)
Optimum Resolution
Maximum Resolution
If a signal that belongs to the following standard signal modes is transmitted from your PC, the screen will automatically be adjusted. If the signal transmitted from the PC does not belong to the standard signal
modes, the screen may be blank even though the power LED turns on. In such a case, change the settings according to the following table by referring to the graphics card user manual.
DisplayPort (S27R75*)
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA DMT, 640 x 480
31.469
59.940
25.175
-/-
VESA DMT, 640 x 480
37.861
72.809
31.500
-/-
VESA DMT, 640 x 480
37.500
75.000
31.500
-/-
VESA DMT, 800 x 600
35.156
56.250
36.000
+/+
VESA DMT, 800 x 600
37.879
60.317
40.000
+/+
VESA DMT, 800 x 600
48.077
72.188
50.000
+/+
VESA DMT, 800 x 600
46.875
75.000
49.500
+/+
VESA DMT, 1024 x 768
48.363
60.004
65.000
-/-
VESA DMT, 1024 x 768
56.476
70.069
75.000
-/-
VESA DMT, 1024 x 768
60.023
75.029
78.750
+/+
VESA DMT, 1152 x 864
67.500
75.000
108.000
+/+
VESA DMT, 1280 x 720
45.000
60.000
74.250
+/+
46
DisplayPort (S27R75*)
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
VESA DMT, 1280 x 800
49.702
59.810
83.500
-/+
VESA DMT, 1280 x 1024
63.981
60.020
108.000
+/+
VESA DMT, 1280 x 1024
79.976
75.025
135.000
+/+
VESA DMT, 1440 x 900
55.935
59.887
106.500
-/+
VESA DMT, 1600 x 900
60.000
60.000
108.000
+/+
VESA DMT, 1680 x 1050
65.290
59.954
146.250
-/+
VESA DMT, 1920 x 1080
67.500
60.000
148.500
+/+
VESA CVT, 2560 x 1440
88.787
59.951
241.500
+/-
VESA CVT, 2560 x 1440
150.919
99.946
410.500
+/-
VESA CVT, 2560 x 1440
182.996
119.998
497.750
+/-
VESA CVT, 2560 x 1440
222.192
144.000
586.586
+/-
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA DMT, 640 x 480
31.469
59.940
25.175
-/-
VESA DMT, 640 x 480
37.861
72.809
31.500
-/-
VESA DMT, 640 x 480
37.500
75.000
31.500
-/-
VESA DMT, 800 x 600
35.156
56.250
36.000
+/+
VESA DMT, 800 x 600
37.879
60.317
40.000
+/+
VESA DMT, 800 x 600
48.077
72.188
50.000
+/+
VESA DMT, 800 x 600
46.875
75.000
49.500
+/+
VESA DMT, 1024 x 768
48.363
60.004
65.000
-/-
HDMI (S27R75*)
47
HDMI (S27R75*)
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
VESA DMT, 1024 x 768
56.476
70.069
75.000
-/-
VESA DMT, 1024 x 768
60.023
75.029
78.750
+/+
VESA DMT, 1152 x 864
67.500
75.000
108.000
+/+
VESA DMT, 1280 x 720
45.000
60.000
74.250
+/+
VESA DMT, 1280 x 800
49.702
59.810
83.500
-/+
VESA DMT, 1280 x 1024
63.981
60.020
108.000
+/+
VESA DMT, 1280 x 1024
79.976
75.025
135.000
+/+
VESA DMT, 1440 x 900
55.935
59.887
106.500
-/+
VESA DMT, 1600 x 900
60.000
60.000
108.000
+/+
VESA DMT, 1680 x 1050
65.290
59.954
146.250
-/+
VESA DMT, 1920 x 1080
67.500
60.00
148.500
+/+
VESA CVT, 2560 x 1440
88.787
59.951
241.500
+/-
VESA CVT, 2560 x 1440
150.919
99.946
410.500
+/-
VESA CVT, 2560 x 1440
182.996
119.998
497.750
+/-
Unique Custom Timing, 2560 x 1440
222.192
144.000
596.807
+/-
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
DisplayPort (S32R75*)
VESA, 640 x 480
31.469
59.940
25.175
-/-
MAC, 640 x 480
35.000
66.667
30.240
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
48
DisplayPort (S32R75*)
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
MAC, 832 x 624
49.726
74.551
57.284
-/-
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
VESA, 1920 x 1080
67.500
60.000
148.500
+/+
VESA, 2560 x 1440
88.787
59.951
241.500
+/-
VESA, 3840 x 2160
133.313
59.997
533.250
+/-
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
HDMI (S32R75*)
VESA, 640 x 480
31.469
59.940
25.175
-/-
MAC, 640 x 480
35.000
66.667
30.240
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
49
HDMI (S32R75*)
Resolution
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
Pixel Clock (MHz)
Sync Polarity (H/V)
MAC, 832 x 624
49.726
74.551
57.284
-/-
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1440 x 900
55.935
59.887
106.500
-/+
VESA, 1600 x 900
60.000
60.000
108.000
+/+
VESA, 1680 x 1050
65.290
59.954
146.250
-/+
VESA, 1920 x 1080
67.500
60.000
148.500
+/+
VESA, 2560 x 1440
88.787
59.951
241.500
+/-
CEA, 3840 x 2160
135.000
60.000
594.000
+/+
――Horizontal Frequency
The time required to scan a single line from the left to the right side of the screen is called a horizontal cycle. The reciprocal number of a horizontal cycle is called horizontal frequency. Horizontal frequency is measured in
kHz.
――Vertical Frequency
Repeating the same picture dozens of times per second allows you to view natural pictures. The repeat frequency is called "vertical frequency" or "refresh rate" and is indicated in Hz.
――This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality.
To avoid this, it is recommended that you select the optimum resolution specified for your product.
――Some resolutions listed in the table above may not be available depending on graphics card specifications.
50
Chapter 12
Appendix
Responsibility for the Pay Service (Cost to
Customers)
A Product damage caused by customer's fault
――When the service is requested, in spite of in warranty, we may charge you for a visit from a service
•• External impact or drop.
technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
•• If a service technician is requested to give instructions on how to use product or simply adjusts
options without disassembling product.
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
•• Use of supplies or separately sold product unspecified by Samsung.
•• Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
•• Remodeling or repairing the product by customer.
•• Using it with incorrect voltage or non-authorised electrical connections.
•• Not following the "cautions" in User Manual.
•• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
•• If a product is reinstalled or devices are connected additionally after installing the purchased
product for the first time.
•• If a product is reinstalled to move to a different spot or to move to a different house.
•• If the customer requests instructions on how to use another company's product.
•• If customer requests instructions on how to use the network or another company's Programme.
•• If customer requests software installation and setup for the product.
Others
•• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
•• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator,
Lamp, Filter, Ribbon, etc.)
――If customer requests a service in case the product has no defect, service fee may be charged. So please
read User Manual first.
•• If a service technician removes/cleans dusts or foreign materials inside of the product.
•• If customer requests an installation additionally after purchasing a product through homeshopping or online.
51
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising