Samsung | MIM-D01AN | Installation guide | Samsung MIM-D01AN Installation guide

Samsung MIM-D01AN Installation guide
DMS2.5(Data Management Server2.5)
MIM-D01AN
MIM-D01ANDZ
BACnet Gateway
MIM-B17BN
MIM-B17BNDZ
LonWorks Gateway
MIM-B18BN
Air Conditioner
user & installation manual
For more information on using the
product, download the user manual
from the product and refer to it.
imagine the possibilities
Thank you for purchasing this Samsung product.
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 1
2019-05-15 오후 3:57:03
Safety Precautions
English
Cautions for operation
• Before using the DMS2.5, BACnet Gateway, LonWorks Gateway, read carefully these instructions.
• After reading the instructions, keep this user's manual in a handy and safe place.
If a user is changed, you must hand over the manuals.
• Never attempt to install the air conditioning system or to move the product by yourself.
WARNING
CAUTION
 Do not attempt to install or repair the product by yourself.
 The product contains no user-serviceable parts. Always consult authorized
service personnel for repairs.
 When moving, consult authorized service personnel for disconnection and
installation of the product.
 Ensure that the wall is strong enough to support the weight of the product.
 Must install the product with rated power supply.
 In the event of a malfunction (burning smell, etc.), immediately stop
operation, turn off the electrical breaker, and consult authorized service
personnel.
 Do not use inflammable gases near the product.
 Do not spill water into the product.
 Do not operate the product with wet hands.
 Do not install the product in a location where it will come into contact with
the combustible gases, machine oil, sulphide gas, etc.
 Do not press buttons with a pointed thing.
 Do not pull or bend the product cable excessively.
 Do not use the product for other purpose.
 Do not spray an insecticide or other combustible things on the product.
 Do not clean the product with benzene, solvents or other chemicals.
 Do not give a shock to the product or disassemble it by yourself.
Cautions for installation
• This user & installation manual describes how to install the DMS2.5, BACnet Gateway, LonWorks
Gateway. For installation of other optional accessories, refer to the appropriate installation manual.
WARNING
CAUTION
 Read carefully this user & installation manual before installation and check if
the product is installed correctly after installation.
 Do not attempt to install or repair this product by yourself.
 This product contains no user-serviceable parts. Always consult authorized
service personnel for repairs.
 When moving, consult authorized service personnel for disconnection and
installation of the product.
 Ensure that the wall is strong enough to support the weight of the product.
 Must install the product with rated power supply.
 The product must be installed according to the national electrical rules by an
installation specialist.
 If you wish to uninstall the product, consult an authorized installation center.
 Do not use inflammable gases near the product.
 Do not install the product in a location where it will come into contact with
combustible gases, machine oil, sulphide gas, etc.
 Avoid locations where acid/alkali solution or special spray is used.
 Choose a location that is dry and sunny, but not exposed to direct sunlight.
Suitable temperature is between 0°C(32 °F) and 39°C(102.2°F).
 Do not spill water into the product.
 Do not apply tensile strength to the cable to avoid cable damage.
 Do not press buttons with a sharp object.
 Do not connect the power cable to the control terminal.
 If the product is installed in a hospital or other special places, it should not
affect other electronic devices.
E-2
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 2
2019-05-15 오후 3:57:03
Consignes de sécurité
Français
Précautions pour le fonctionnement
• Avant d’utiliser le DMS2.5, BACnet Gateway, LonWorks Gateway, lisez attentivement ces consignes.
• Après en avoir pris connaissance, conservez ce manuel d’utilisation dans un lieu sûr et à portée de main.
En cas de changement d’utilisateur, vous devez remettre les manuels.
• Ne tentez jamais d’installer le climatiseur ou de déplacer le produit par vous-même.
AVERTISSEMENT
ATTENTION
 Ne tentez pas d’installer ou de réparer vous-même le produit.
 Le produit ne contient aucun composant interne susceptible d’être réparé par l’utilisateur.
Consultez toujours le personnel d’entretien agréé pour toute réparation.
 En cas de déplacement, consultez le personnel d’entretien agréé pour tout débranchement et
toute installation du produit.
 Assurez-vous que le mur est suffisamment résistant pour supporter le poids du produit.
 Vous devez raccorder le produit à une installation supportant sa puissance nominale.
 En cas de dysfonctionnement (odeur de brûlé, etc.), arrêtez immédiatement le
fonctionnement, coupez le disjoncteur électrique et consultez le personnel d’entretien qualifié.
 N’utilisez pas de gaz inflammable à proximité du produit.
 Ne renversez pas d’eau dans le produit.
 Ne manipulez pas le produit si vous avez les mains mouillées.
 N’installez pas le produit dans un lieu où il sera en contact avec des gaz combustibles, de
l’huile de machine, de l’hydrogène sulfuré, etc.
 N’appuyez pas sur les boutons avec un objet pointu.
 Ne tirez pas sur le cordon d’alimentation du produit et ne le pliez pas excessivement.
 N’utilisez pas le produit dans un autre but que celui auquel il est destiné.
 Ne vaporisez pas d’insecticide ou autre produit combustible sur le produit.
 Ne nettoyez pas le produit en utilisant du benzène, des solvants ou autres produits chimiques.
 N’appliquez pas de choc sur le produit et ne le désassemblez pas non plus vous-même.
Précautions pour l’installation
• Ce manuel d’utilisation et d’installation décrit comment installer le DMS2.5, BACnet Gateway,
LonWorks Gateway. Pour obtenir des informations sur l’installation d’autres accessoires
optionnels, reportez-vous au manuel d’installation correspondant.
AVERTISSEMENT
ATTENTION
 Veuillez lire attentivement ce manuel d’utilisation et d’installation avant l’installation, puis
vérifiez si le produit est correctement installé.
 Ne tentez pas d’installer ou de réparer vous-même ce produit.
 Ce produit ne contient aucun composant interne susceptible d’être réparé par l’utilisateur.
Consultez toujours le personnel d’entretien agréé pour toute réparation.
 En cas de déplacement, consultez le personnel d’entretien agréé pour tout débranchement
et toute installation du produit.
 Assurez-vous que le mur est suffisamment résistant pour supporter le poids du produit.
 Connectez impérativement le produit à une installation supportant sa puissance nominale.
 Conformément aux règles électriques nationales, le produit doit être installé par un
technicien d’installation.
 Si vous voulez désinstaller le produit, consultez un centre d’installation agréé.
 N’utilisez pas de gaz inflammable à proximité de l’appareil.
 N’installez pas le produit dans un lieu où il sera en contact avec des gaz combustibles,
de l’huile de machine, de l’hydrogène sulfuré, etc.
 Évitez les emplacements où des solutions acides/alcalines ou des pulvérisateurs
spéciaux sont utilisés.
 Choisissez un emplacement sec et lumineux, mais non exposé à la lumière directe du
soleil. La température adaptée se situe entre 0 °C (32 °F) et 39 °C(102,2 °F).
 Ne renversez pas d’eau dans le produit.
 Ne soumettez pas le câble à un effort de tension qui pourrait l’endommager.
 N’appuyez pas sur les boutons à l’aide d’un objet pointu.
 Ne branchez pas le câble d’alimentation à la borne de commande.
 Si le produit est installé dans un hôpital ou dans
d’autres endroits spéciaux, il ne doit pas affecter les
autres appareils électroniques.
E-3
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 3
2019-05-15 오후 3:57:03
Contents
 Safety Precautions ..............................
Before Installing the DMS2.5 ........
 Accessories .............................................
 Viewing the Parts .................................
 Product Dimensions ............................
 System Architecture ............................
 Compatible Devices ...............................
 Installing the DMS2.5 ......................
 Setting the Computer Environment.
 Setting the DMS2.5 ...........................

Note
2
5
6
7
9
10
11
13
19
21
 Tracking ...................................................
 Setting the Power Distribution .......
Appendix ...................................................
BACnet Gateway setting ...................
 Viewing LonWorks Gateway’s Parts
 Product Dimensions ............................
 LonWorks Gateway setting ...............
 Specifications .........................................
 License ......................................................


34
42
44
47
75
77
78
102
103
 T he contents and pictures used in this user & installation manual may be
changed without advance notice for the functional reinforcement and
improvement of a product.
This user & installation manual is for DMS2.5, BACnet Gateway, LonWorks
Gateway installation.
Refer to page 47~74 to check BACnet Gateway installation.
Refer to page 75~101 to check LonWorks Gateway installation.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
The lowest set temperature is limited to 20 degree in the UAE according to UAE.S
5010-5:2016.
E-4
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 4
2019-05-15 오후 3:57:03
Before Installing the DMS2.5
Checks before installation
1
DMS2.5 IP
Basically, only Private IP can be set to IP address. To use Public IP, you must
set Enable public IP as ‘Enable’ from the menu [System Settings]  [System
environment setting].
- Private IP range : 10.0.0.0 ~ 10.255.255.255, 172.16.0.0 ~ 172.31.255.255,
192.168.0.0 ~ 192.168.255.255
- Public IP range: IP except for Private IP range and 127.0.0.1(localhost)
D
MS2.5 supports DHCP. If Public IP must be assigned from DHCP, you must
set Enable public IP as ‘Enable’ from the menu [System Settings]  [System
environment setting].
 DHCP(Dynamic Host Configuration Protocol)
An Internet protocol for automating the configuration of computers that use TCP/IP.
DHCP is used to automatically assign IP addresses.
In other words, the IP address of the host is supported only when the PC is on.
2
Network related equipments
 DHCP(Dynamic Host Configuration Protocol)
An Internet protocol for automating the configuration of computers that use TCP/IP.
DHCP is used to automatically assign IP addresses.
In other words, the IP address of the host is supported only when the PC is on.
3
Installation connection wire
 The LAN cable and the communication cables from OnOff controller/interface
modules must be installed in such a way that the wires can be connected to the
DMS2.5 with ease.
Note
DMS2.5 supports Static IP or Dynamic IP. Web browser or S-NET series accesses
DMS2.5 using its IP address. If the web browser or S-NET series which accesses to
DMS2.5 are installed in a PC and the PC’s IP is set to Public IP, you must register
the Public IP to DMS2.5 to access.
A
static IP from an internet service provider must be used if xDSL (ADSL, VDSL) is
supported.
 Use this product only in a separate dedicated network. Samsung electronics is not
liable for any problems caused by connecting it to the Internet or an intranet.
E-5
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 5
2019-05-15 오후 3:57:04
Accessories
Make sure you have each item. Supplied items may vary depending on your
country or service provider.
Item
DMS2.5
Adapter
Power cable
M4 x16 Screw
Quantity
1
1
1
6
Shape
User & Installation
manual
Cable tie
1
1
 The DMS2.5 must be installed by a trained installer.

Ensure the main power is turned off before installing
the DMS2.5.
 Be sure to use adapter and power cable we provide.

The shape of power cable may differ depending on the
model.

The power cable and the communication cable must
be installed according to the national electrical wiring
regulations.

LonWorks communication cable should use the cable
which fits to the specification provided by Echelon.
E-6
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 6
2019-05-15 오후 3:57:04
Viewing the Parts
Main Parts
DMS2.5 Exterior
LCD Display
Shows current time and IP address. Various
messages will be displayed depending on
button input.
LCD operation button
There are 4 buttons(Menu, ▼(Down), ▲(Up),
Set) and you can access menu and move,
check the menu.
LED Indicator
Check 15 LED status such as Power, CPU-Alive,
Ethernet-Linked/Active, COM1~5-TX/RX and
Check
DMS2.5 Bottom cover
Unfasten 2 screws on the bottom and
separate the bottom cover from DMS2.5.
Then check cable connection part.
LED Indicator
Item
Power
CPU Alive
Name
Status
Power indicator
Turns blue when the
power is supplied.
CPU operation indicator
Blinks in orange with
1 second intervals during
normal operation.
Ethernet–Linked Internet connection indicator
Turns green during
normal connection.
Ethernet–Active Internet data transmission/reception indicator
Blinks in orange during
normal transmission/
reception.
COM1~5 – TX
Channel 1~5 OnOff controller/Outdoor unit
Data transmission Indicator
Blinks in green during
normal transmission.
COM1~5 – RX
Channel 1~5 OnOff controller/Outdoor unit
Data reception Indicator
Blinks in green during
normal reception,
Indoor/Outdoor unit/Communication check Indicator
Turns green when notice
occurs.
Check
E-7
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 7
2019-05-15 오후 3:57:04
Viewing the Parts (Continued)
DMS2.5 Cable Connection Part
RS485 Communication Terminal
DI Terminal1
DI Terminal2
Power Terminal
DO Terminal3
SD Card Socket
Reset Button
Name
DO Terminal4
Reserved
Cable tie groove
Ethernet Terminal
Description
DI Terminal1
Digital Input connection terminal, Channel1~Channel5
DI Terminal2
Digital Input connection terminal, Channel6~Channel10
DO Terminal3
Digital Output connection terminal, Channel1~Channel5
DO Terminal4
Digital Output connection terminal, Channel6~Channel8
Reset Button
Reset DMS2.5
Power Terminal
SD card socket
RS485
Communication
Terminal
Connect DMS2.5 adapter
Sub memory (for program update and set information saving) socket
Connect for RS485 communication with devices such as OnOff
controller/Outdoor unit
- COM1 ~ COM5
Ethernet Terminal
Connect LAN cable
Cable tie groove
Groove for arranging cables
E-8
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 8
2019-05-15 오후 3:57:04
Main Parts
DMS2.5 Interior
Display Board
20-pin Cable
Main Board
40-pin Cable
Sub Board
Note
 If you need external circuit configuration, consult with the manufacturer.
 Refer to page 18 for DI contact input operation.
Product Dimensions
64.80
(Unit : mm)
255
240
E-9
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 9
2019-05-15 오후 3:57:05
System Architecture
S-NET 3
Web Client
TCP/IP
OnOff
Controller
PM 05:45
R5 485
Touch
Centralized
controller
DMS2.5
Internet
RMS Center
SIM/PIM
Outdoor
Unit
Power Meter
Max 256 Indoor units
(DVM Series)
onnecting outdoor unit and DMS2.5.
C
- You can control up to 80 outdoor units and 256 indoor units by using DMS2.5.
 You can connect up to 16 (outdoor) units per each communication channel of the DMS2.5.
 The maximum number of indoor units (including ERV and MCU) that can be connected to each
communication channel of DMS2.5 RS485 is 128.
- If the number of connected outdoor unit increases, it may take long time for tracking.
(Max. 30 minutes)

 F or devices that support new communication, you must set the communication mode of
the channel to ‘NEW’ from ‘System settings  Tracking’ menu.
Set of Indoor/outdoor units, with conventional communication type, cannot be connected
to DMS2.5 with new communication.
 When ‘NEW’ is set as communication mode of the channel, virtual OnOff controller address
will be assigned.
(Channel 0: Virtual OnOff controller 11, Channel 1: Virtual OnOff controller 12,
Channel 2: Virtual OnOff controller 13, Channel 3: Virtual OnOff controller 14,
Channel 4: Virtual OnOff controller 15)
E-10
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 10
2019-05-15 오후 3:57:06
Compatible Devices
No
1
2
Devices
Indoor Unit
Outdoor Unit
Model
DVM S HR, DVM S HP, DVM ECO,
DVM S WATER GEO, DVM S cooling
only outdoor units and indoor units
that can be connected to these
outdoor units
OnOff controller/
Touch Centralized MCM-A202DN, MCM-A300N
controller
Note
DVM, CAC indoor/outdoor units and
ERV product groups that support NASA
communication
OnOff controller: Centralized controller
3
SIM
MIM-B12N
Needed for EHP power distribution
4
PIM
MIM-B16N
Needed for EHP power distribution
RS485 comm. type
Connected with SIM
Needed for power distribution
( Please consult Samsung for compatible
power meters)
Pulse type
Connected with PIM
Pulse Width: 20~400(ms)
Pulse: 1~10000(Wh/Pulse)
5*
Watt-hour Meter
 Products with ‘* ’ are not Samsung products and must be purchased separately.
(Only selected power meters may be used for protocol compatibility issues.)
E-11
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 11
2019-05-15 오후 3:57:06
Compatible Devices (Continued)
Maximum Devices Attachable
Devices
Max.
Note
Indoor Unit
256
Tracking error occurs if exceeded
The maximum number of indoor units
(including ERV and MCU) that can be
connected to each DMS communication
channel is 128.
OnOff controller/
Touch Centralized controller
75
Must not exceed 15 units per each
RS485 communication terminal
Outdoor unit
80
Must not exceed 16 units per each
RS485 communication terminal
SIM/PIM
8
Watt-hour Meter
64
Maximum 8 units can be connected to
1 SIM/PIM.
The sum of OnOff controller, touch centralized controller, and SIM/PIM interface module
that can be connected to each DMS2.5 communication channel should be 15 or less.
E-12
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 12
2019-05-15 오후 3:57:06
Installing the DMS2.5
1
Separate the installation plate on the rear side of DMS2.5.
2
Fix the installation plate on the wall using 4 screws.
3
Hang the DMS2.5 on the groove which is on the top of
the installation plate.
Installation
plate
4
Fix the installation plate and DMS2.5 using 2 screws.
 Depending on the installation environment, fix DMS2.5
using assistant holes.
(Screws for assistant hole are not provided by our
company.)
5
Assistant hole
If you install DMS2.5 inside of the wall or wiring from the rear
side is needed, use wiring groove on the bottom of DMS2.5.
To prevent breakdown and damage of DMS2.5, and for safe
usage, it is recommended to install DMS2.5 on the wall.
Wiring groove
E-13
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 13
2019-05-15 오후 3:57:06
Installing the DMS2.5 (Continued)
Connecting Outdoor Unit
1
Unfasten the 2 screws on the bottom of the DMS2.5 front
cover. Hold the bottom 2 sides of the DMS2.5 and push
downwards to slide open the cover.
2
Connect the adapter to the power terminal.
 Arrange the adapter as the right figure.
Adapter
3
Separate 1 terminal block from 5 terminal blocks that
are attached to RS485 communication terminal of the
DMS2.5. Then, connect outdoor unit communication
cable (R1, R2)] to the terminal block.(R1A, R2B)
4
Connect LAN cable to the Ethernet terminal of DMS2.5.
Then arrange it using cable tie.
5
Fasten the bottom cover of DMS2.5 and fix it using
2 screws.
Connect
communication
cable
Cable tie
LAN cable
Maximum 80 Outdoor units can be connected to one DMS2.5.
E-14
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 14
2019-05-15 오후 3:57:07
Connecting SIM
1
Unfasten the 2 screws on the bottom of the DMS2.5 front
cover. Hold the bottom 2 sides of the DMS2.5 and push
downwards to slide open the cover.
2
Connect the adapter to the power terminal.
 Arrange the adapter as the right figure.
Adapter
3
Separate 1 terminal block from 5 terminal blocks which
are attached to RS485 communication terminal.
Then, connect SIM/PIM communication cable to the
terminal block.
Connect
communication
cable
4
Connect LAN cable to the Ethernet terminal of DMS2.5.
Then arrange it using cable tie.
5
Fasten the bottom cover of DMS2.5 and fix it using
2 screws.
Cable tie
LAN cable
Maximum 8 SIM/PIM units can be connected to one DMS2.5.
E-15
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 15
2019-05-15 오후 3:57:07
Installing the DMS2.5 (Continued)
Using the DI External Contact Control (Optional)
Setting the External Contact Control Pattern
 You
can set the system settings through contact control pattern.
1
Select [System Settings] menu and click [System environment setting].
2
Click [Edit] from ‘Select the contact control pattern’.
3
Select the pattern you want to check.
 Pattern 1[No external input]: No operation will be made when inputting
contact point control signal.
 Pattern 2[Level(Emergency stop)]: Commands that stop all indoor unit
operation and disable remote control when inputting contact point control
signal. In level emergency stop status, it will not be controlled even if the
command is set from upper controller.
 Pattern 3[Level(Operation/Stop)]: Level signal input timing.
It changes operation/stop status of all indoor units.
 Pattern 4[pulse (Operation/Stop,Disable/Enable)]:
Pulse signal. It changes operation/stop status of all indoor units.
4
Click [Save] after setting is completed.
5
Click [OK] when “This information will be modified. Do you want to proceed?”
message window appears.
6
“Reading data from DMS2.5. Please wait.” message appears and saving is
completed. Then, system environment setting screen appears again with all items
are disabled.
Note
Pattern 1 is set as factory setting.
 D
MS2.5 has total 10 DI ports. However, actually used DI
ports are Ch1 and Ch2, and the rest of the ports (Ch3~Ch10)
are for additional functions. Therefore, make sure to
connect Ch1 or Ch2 when using it.
 For DO, Ch1 and Ch2 are currently used inside of DMS2.5.
Ch9 and Ch10 are reserved in case of need. Therefore you
can only use Ch3~Ch8.
E-16
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 16
2019-05-15 오후 3:57:07
Contact control Pattern
Pattern
Pattern1
Control
▶ No external input (Factory default setting)
When you input contact control signal in port 1, there will be no response.
▶ Level input (Emergency stop)
1. If the contact control signal is changed to ON, emergency stop status and all the
indoor units are given ‘Stop’ command, and controlling using remote controller is
impossible.
2. During the emergency stop, the DMS2.5 will ignore any request from the upper
controllers.
Pattern2
3. During the emergency stop, the DMS2.5 will ignore previously set schedules.
4. When the contact control signal changes from ON to OFF, DVM goes into normal
operation status and returns to the remote control status before emergency stop.
5. Even if the contact control signal of port 1 changes from ON to OFF, there will be no
change to the indoor unit.
6. When you input contact control signal in port 2, there will be no response.
▶ Level input (Operation/Stop, Remote control Enable/Disable)
1. If the contact signal of port 1 changes from OFF to ON, all indoor units will be given
‘Operation‘ command.
2. If the contact signal of port 1 changes from ON to OFF, all indoor units will be given
‘Stop‘ command.
3. If the contact signal of port 2 is OFF, you cannot control all indoor units using
remote controller.
Pattern3
4. If the contact signal of port 2 changes from OFF to ON, you can control all indoor
units using remote controller.
5. If the contact signal of port 2 changes from ON to OFF, you cannot control all indoor
units using remote controller.
6. Control command from the upper controller will be operated regardless of the
contact point status.
7. DVM system control using Schedule control will be operated regardless of the
contact point status.
▶ Pulse input (Operation/Stop)
1. Valid pulse duration for input signal is 0.5~1.0 second.
DMS2.5 ignores the signal which has shorter than 0.5 second duration, longer than
1.0 second Pulse width.
2. When Pulse input signal is ON in Port 1. all indoor units will be given ‘Operation‘
command.
Pattern4
3. When Pulse input signal is ON in Port 2. all indoor units will be given ‘Stop‘
command.
4. DVM control command from the upper controller will be operated regardless of
Pulse input signal.
5. DVM system control using Schedule control will be operated regardless of
Pulse input signal.
E-17
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 17
2019-05-15 오후 3:57:07
Installing the DMS2.5 (Continued)
DI(Digital Input) Circuitry according to Contact
control Pattern

P
attern 2 (May be used for connection with a fire sensor)
DMS2.5
Emergency Stop/Resume Operation
CH1
CH2

No Connection
P
attern 3 (External contact signal control)
DMS2.5
Operation/Stop A/C
CH1
Enable/Disable remote control
CH2

P
attern 4 (Pulse signal control)
DMS2.5
CH1
CH2
A/C
Operation
A/C
Stop
E-18
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 18
2019-05-15 오후 3:57:08
Setting the Computer Environment
1
Device related to network (Purchase separately)
 Computer with a LAN Card
 HUB or network cable(Cross·Direct cable)
2
Computer web browser specification
 Internet Explorer 11 or later version
 Silverlight 2.0 or later version
Note
 A cross cable is used when connecting to PC directly.
It is produced as transmission and reception cables are
crossed. Cable 1, 2, 3, and 6 are crossed each other.
 Visit internet homepage (http://www.microsoft.
com/silverlight/) to download Silverlight. Or you
can download it through the download link which is
noticed automatically when you access to DMS2.5 for
the first time.
Connect DMS2.5 and Computer
Connect DMS2.5 and Computer directly
S-NET3
DMS2.5
Cross cable
Connect DMS2.5 and Computer using HUB
HUB
S-NET3
DMS2.5
LAN cable
E-19
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 19
2019-05-15 오후 3:57:08
Setting the Computer Environment (Continued)
Computer Settings for DMS2.5 Connection

All
settings of DMS2.5 will be arranged in web page which
built in DMS2.5. You should access to DMS2.5 IP to use
DMS2.5 web page.
Set your computer settings as follows.

DMS2.5
Factory default setting
DMS2.5 IP : 192.168.0.100
IP Setting (Recommended)

To
access to DMS2.5 IP, set the network information of
DMS2.5 connected computer as follows.
IP address :192.168.0.1(~253)
Except 100
 Subnet mask : 255.255.255.0
 Default gateway : 192.168.0.1

E-20
1
Select [My network Settings] icon and click [Properties]
using right button.
2
Select [Local area connection] icon and click [Properties]
using right button from the network connection folder.
3
[Internet protocol(TCP/IP)] and click [Properties] using
right button from the local area connection property
window.
4
Enter “192,168,0,1” in IP address field, “255,255,255,0”
for subnet mask address, and “192,168,0,1” for default
gateway.
5
Click [OK] after setting.
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 20
2019-05-15 오후 3:57:08
Setting the DMS2.5
DMS2.5 Connection and Login
Address bar
1
Click internet explorer icon(
2
When internet explorer window appears, enter IP address
(https://192.168.0.100) on the address field then press [ENTER].
1) A
t initial access, security certificate warning popup message will appear as
shown. This message appears since DMS2.5 used the certificate of its own, so
it will not appear if DMS2.5 certificate is registered on web browser. DMS2.5
certificate must be registered because the message will appear every time and it
is not safe for security if it is not registered. Also, it should be registered to all PCs
that are connecting to DMS2.5.
) twice on your computer.
You must stop connecting due to security problem if
the message appears even if you registered DMS2.5
certificate.
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 21
E-21
2019-05-15 오후 3:57:08
Setting the DMS2.5 (Continued)
2) Registering DMS2.5 certificate on web browser
A. Select ‘Content’ tap in ‘Tools’  ‘Internet options’, and click ‘Certificates’.
B. Select ‘Trusted Root Certification Authorities’ and click ‘Import’.
C. Click ‘Next’.
E-22
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 22
2019-05-15 오후 3:57:08
D. Select ‘Browse’ and find DMS2.5 certificate, and click ‘Next’. DMS2.5 certificate
can be downloaded from [System environment setting].
E. Select ‘Place all certificates in following drive’ and click ‘Next’.
F. Click ‘Finish’, and click ‘Yes’ when security warning appears.
E-23
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 23
2019-05-15 오후 3:57:09
Setting the DMS2.5 (Continued)
3
If it is the first time to access DMS2.5, “Install Microsoft Silverlight” message will appear.
 If Microsoft Silverlight has already been installed, the screen will not appear.
4
Click [Run] button and continue installation.
After installation, access DMS2.5 again.
Silverlight operates normally with Windows 7 or later version. It may not operate
normally with former version of Windows.
E-24
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 24
2019-05-15 오후 3:57:09
5
5
Enter ID and password when DMS2.5 main web page appears. Then click [LOGIN].
 Depending on authorization settings set by the administrator, access to some
functions may be restricted.
 For user authorization setting, refer to System
settings  User authorization management.
The default DMS2.5 user ID is ‘admin’ and password is ‘ac0530’.
Note
Only authorized users can access to web page.
Connection speed may slow down.
Fewer than 5 concurrent users are recommended.
DMS2.5 manager should change ID and password for security and management.
LOGOUT :If you want to log out, click [LOGOUT] on the top of the menu. DMS2.5
will be ended.
E-25
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 25
2019-05-15 오후 3:57:09
Setting the DMS2.5 (Continued)
DMS2.5 System Environment Setting (Network settings)

Y
ou can set and check information about DMS2.5 installation operation.
DMS2.5 Network Information Setting
1
Select [System Settings] menu and click [System environment setting].
2
Click [Edit] from DMS2.5 network information window.
3
When text boxes of IP address, subnet mask address, default gateway and DNS
server are enabled, enter values for each item.
 15 letters can be entered for each item.
 Each item should match with the network address form.
When checking DHCP
 If you check the ‘DHCP’, the text boxes of IP address, subnet mask address,
default gateway and DNS server will be disabled.
 If you want manual setting, uncheck ‘DHCP’ and then enter network
information manually.
4
After clicking [Save], click [OK] when the message window appears.
 If you click [OK] after setting network information as ‘Edit’, current internet
explorer will be closed. And when you access DMS2.5 again, you can access
DMS2.5 using manually setting IP.
 If you click [OK] after setting network information as ‘DHCP’, current internet
explorer will be closed. And when you access DMS2.5 again, you can access
DMS2.5 using the IP displayed in LCD Display.
E-26
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 26
2019-05-15 오후 3:57:09
Note


F actory setting is as follows.
- IP address: 192.168.0.100
- Subnet mask address: 255.255.255.0
- Default gateway: 192.168.0.1 - DNS server: 0.0.0.0
If you enabled the function by checking ‘DHCP‘, you can check changed network
information on the external LCD display.
 If ‘DHCP’ is set, IP address from DHCP server will be displayed.
 DMS2.5 gets automatically set IP address when you activate DHCP function.
When connecting DMS2.5 to S-NET series, you can connect them using the IP.
However the auto setting IP address can be changed by events such as network
environment of restart.
In this case, it may cause communication failure between S-NET series and
DMS2.5. Therefore it is not recommended to connect DMS2.5 using DHCP
address and S-NET series.
 Refer to the user manual if you want to check other items of the system
environment setting, tracking which collects information about indoor and
outdoor units connected to DMS2.5, and setting for power distribution. To
download the user manual, select [User manual] after selecting [System
settings] menu.
 This product must be used in a dedicated network
because it cannot respond to network attacks such as
hacking and viruses. When it is connected to the Internet
or an intranet (ex: an office LAN), it could be a risk of
illegal approach. Also, this may change it to a harmful
connection for other network devices. This is not the
responsibility of Samsung Electronics and not included in
compensation for the damage.
E-27
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 27
2019-05-15 오후 3:57:09
Setting the DMS2.5 (Continued)
System Time Setting
1
Select [System Settings] menu and click [System environment setting].
2
Click [Edit] from system time setting.
3
Enter system time(year/month/day/hour/minute/second).
 You can enter only numbers.
 Year: You can enter from 1980 to 2035.
 Month: You can enter from 1 to 12.
 Day: You can enter from 1 to 31.
 Hour: You can enter from 0 to 23.
 Minute: You can enter from 0 to 59.
 Second: You can enter from 0 to 59.
4
Click [Save] and message window appears. Then click [OK].
 “Reading data from DMS2.5. Please wait.” message appears and saving is
completed. Then, system environment setting screen appears again as all
items are disabled.
Note
System time reflects set current time.
E-28
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 28
2019-05-15 오후 3:57:09
Setting the Language
1
Select [System Settings] menu and click [System environment setting].
2
Click [Edit] from language selection.
3
Select a language you want then click [Save].
4
Click [OK] when “This operation needs DMS2.5 to be restarted. Do you want to
apply the setting?” message appears.
 Click [OK] and current web browser will be closed. DMS2.5 will restart and it
may take approximately 1 minute.
E-29
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 29
2019-05-15 오후 3:57:09
Setting the DMS2.5 (Continued)
DMS2.5 Name Setting
1
Select [System Settings] menu and click [System environment setting].
2
Click [Edit] from DMS2.5 name setting window.
3
Enter name of DMS2.5 when DMS2.5 name field enabled.
 You can use maximum 30 letters including English alphabets and special
symbols.
 When DMS2.5 name is set, the name will be displayed on the top title bar of
web browser.
4
Click [Save] after setting is completed.
5
Click [OK] when “This information will be modified. Do you want to proceed?”
message window appears.
6
“Reading data from DMS2.5. Please wait.” message appears and saving is
completed. Afterwards, system environment setting screen appears again as
all items are disabled.
 You can check new DMS2.5 name on the title bar of web browser.
Note
Name of DMS2.5 is set to blank as factory default.
E-30
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 30
2019-05-15 오후 3:57:09
Error Mail Forwarding Setting
1
Select [System Settings] menu and click [System environment setting].
2
Click [Edit] from error mail forwarding setting.
3
Set all the items as the value you want when all items fields are enabled.
 If you select ‘Apply’, you should enter e-mail address, SMTP server ID,
password, and SMTP server address.
 If you select ‘Not apply’, E-mail, ID, PW and SMTP server items will not affect.
4
Click [Save] after setting is completed.
5
Click [OK] when “This information will be modified. Do you want to proceed?”
message window appears.
6
“Reading data from DMS2.5. Please wait.” message appears and saving is
completed. Afterwards, system environment setting screen appears again
with all items are disabled.
Note
 In factory setting, ‘Not apply’ is checked and item fields
(E-mail, ID, PW, SMTP server) are blank.
 E-mail forwarding function deals with the server supporting SSL.
E-31
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 31
2019-05-15 오후 3:57:09
Setting the DMS2.5 (Continued)
Setting Enable public IP
1
Select [System Settings] menu and click [System
environment setting].
2
Click [Edit] on Enable public IP section.
3
Select whether to use Public IP or not.
 When you select ‘Enable’, you must register the Public IP of
PCs or network devices to access DMS2.5 from the PCs or
network devices.
4
Click [Save].
Setting Public IP of upper controller
1
Select [System Settings] menu and click [System
environment setting].
2
Click [Edit] on Public IP of upper controller section.
3
Register the Public IP of PCs or network devices to access
DMS2.5 from the PCs or network devices.
 Select ‘Apply’ after entering the Public IP to access
DMS2.5.
4
Click [Save].
E-32
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 32
2019-05-15 오후 3:57:09
System setting initialization
192.168.0.100
06:12:13(AM)
1
Press [Menu], [], [] or [Set] on LCD if IP and current time are displayed on
LCD screen.
 Main menu screen appears.
 Initialization is not possible in the screen which time information is
displayed.
MAIN MENU
1.IP Config
2
Press [Menu]  []  []  []  [Menu] buttons in order in main menu
screen.
 Caution will be displayed on LCD Display.
Are you sure?
YES:Set, NO:Menu
3
Initialize DMS2.5 by clicking [Set] when caution phrase appears.
 If you press [Menu] button, turns back to main menu without initialization.
When initializing system setting, all saved data in DMS2.5 will be deleted.
After initialization, saved data and IP address will be same as factory setting.
E-33
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 33
2019-05-15 오후 3:57:09
Tracking
 What is tracking?
Tracking is an operation that finds devices which are connected to DMS2.5.
Through tracking operation, devices which are connected to DMS2.5 can recognize if they
are connecting to DMS2.5.
To supervise and control system air conditioner using DMS2.5, tracking should be done first.
 Things you can do through tracking
Checking the number of devices installed, setting communication mode for each channel,
DVM tracking, Renaming is possible through tracking.
 Execute tracking
(1) Connect DVM device
- Connect the device to COM1~COM5.
(2) Set communication mode for each channel.
- Set proper communication mode which fits to the devices connected in step (1).
- Be careful that if communication mode is not properly set, the device will not be found
through tracking.
(3) Execute tracking - Execute DVM tracking.
- DVM tracking is an operation that finds system air conditioner devices such as indoor/
outdoor unit and watt-hour meter.
(4) Name setting for each device.
- Name setting for each device is a function that sets the name of connected devices.
Set the name which shows installation location of the device.
 Communication mode setting for each channel
Roles
- It records what devices are connected to COM1~ COM5 of DMS2.5.
- Through tracking, DMS2.5 searches proper devices which fits to user’s setting.
- Select proper communication mode which fits to connected device.
What is communication mode?
- Outdoor unit, OnOff controller, SIM, PIM can be connected to DMS2.5.
- Following is the list of devices that can be communicated through each communication
mode.
▶ NEW mode: O
nOff controller, outdoor units, and SIM/PIM which support new
communication mode.
▶ IM mode: IM mode cannot be set, but it can be used for function change or new function
with an updated version.
E-34
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 34
2019-05-15 오후 3:57:09
Setting Communication Mode for Each Channel
1
Select [System Settings] menu and click [Tracking].
2
Click [Edit] from communication mode for each channel setting.
 [Edit] will change to [Cancel].
 Selection buttons are enabled. However, the channels which have searched
device maintains its selection button disabled.
3
When each channel is enabled, check the communication mode you want to
set for each channel.
 You cannot change the communication mode of channel which has
currently connected device.
 When ‘NEW’ is set as communication mode, setting will allow tracking,
monitoring and controlling devices that support NEW communication mode.
 IM mode cannot be set, but it can be used for function change or new function
with an updated version.
4
Click [Save] after setting is completed.
 “Reading data from DMS2.5. Please wait.” message appears and saving is
completed. After that, tracking page with disabled items will be displayed
again.
 If you click [Cancel], check boxes will be disabled and [Cancel] will change
to [Edit].
E-35
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 35
2019-05-15 오후 3:57:09
Tracking (Continued)
DVM Tracking
1
Select [System Settings] menu and click [Tracking].
2
Click [DVM Tracking].
3
Enter administrator’s password and then click [OK].
4
Tracking information window pops up. Check it and click
[OK] to continue.
 Execute tracking depending on the communication
mode set by communication mode setting for each
channel.
5
“Tracking is in progress. Please wait.” message appears.
 Tracking takes from few seconds to several ten minutes.
However, it may vary depending on the number of
installed controllers. (Max. 30 minutes)
E-36
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 36
2019-05-15 오후 3:57:09
6
Tracking completed message will appear.
Select Zone initialization mode you want.
 No initialization: No zone information initialization will
be made.
 Individual initialization: Initialize zone information as
individual mode.
- Individual mode: Arrange by indoor unit main address
on monitoring page.
 Group initialization: Initialize zone information as group
mode.
-G
roup mode: Create group by indoor unit group
address (RMC) on monitoring page.
 Individual mode and group mode can be changed in
[Zone Setting & Edit].
7
Page will be refreshed by clicking [OK]. Then you can
check tracking result.
Note
If tracking is executed successfully while ‘NEW’ is set as
communication mode for each
channel, virtual OnOff controller will be assigned to each
channel.
 If there is no searched oudoor unit, OnOff controller, SIM/
PIM, it is regarded as DVM
tracking failure.
 If there are devices which have same address, first
searched device will be registered only.
※Searching order is not fixed.
 The number of OnOff controller does not contain the
number of virtual OnOff controller.
 Total number of indoor units includes general indoor
units, ERV, AHU, Fresh ducts, ERV PLUS, Hydro Unit,
Hydro Unit HT, DVM CHILLER and FCU Kit.
 I f you execute tracking, system setting will be
initialized.
 If tracking result does not match with actual
installation information, there can be critical error in
additional functions such as power distribution.
 Make sure that tracking information matches to actual
installation information after tracking.

If there are errors on indoor and outdoor units while
tracking, the units may not be matched.
E-37
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 37
2019-05-15 오후 3:57:09
Tracking (Continued)
Disconnect All Devices
Function
Initialize searched device status in DMS2.5.
Monitoring and controlling of all the connected devices to DMS2.5 will be stopped
when you use this function.
 Connect searched device to the other channel and execute tracking.
If the other device is searched in the channel you want to use, use ‘Disconnect all
devices’ function.
 If you use this function, DMS2.5 device connection status will be initialized.
Disconnect All Devices
1
Select [System Settings] menu and click [Tracking].
2
Click [Disconnect all devices].
3
Enter administrator’s password and then click [OK].
4
Disconnect all devices information window pops up. Check it and click [OK] to
continue.
5
“Reading data from DMS2.5. Please wait.” message appears.
After completing disconnect all devices operation, page will be refreshed.
Note
A
fter executing disconnect all devices function, device search status of
DMS2.5 will be initialized.
Y
ou should execute tracking again after using disconnect all devices
function.
E-38
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 38
2019-05-15 오후 3:57:10
Renaming the Device
1
Select [System Settings] menu and click [Tracking].
2
Click [Edit] on the bottom of tracking device list.
 [Edit] will change to [Cancel].
 When the type of the device is displayed, NEW communication address will be
shown with it.
Note
3
If you press [Cancel] button, [Cancel] will change to [Edit], and the changed
name of device will be restored to original name.
Enter the device name, which is saved in the PBA of indoor unit and outdoor
unit, in the Device name field or enter the name, which is saved in the
DMS2.5, in the Name field.
 You cannot use special symbols as Device name and Name.
 Select the check box beside ‘Device name’ if you want to use the name of the
device (that supports NEW communication) which is saved in the PBA
4
Click [Save] after setting is completed.
 “Reading data from DMS2.5. Please wait.” message appears and saving is
completed. After that, tracking page with disabled items will be displayed
again.
 If you click [Cancel], input fields are disabled and [Cancel] will change to
[Edit].
E-39
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 39
2019-05-15 오후 3:57:10
Tracking (Continued)
DMS DI•DO Port Setting
1
Select [System Settings] and then click [Tracking].
2
Click [Setting] which is next to DMS DI•DO of device list.
3
Click [Edit] which is on the bottom of DMS DI•DO setting page.
 [Edit] will change to [Cancel].
4
Edit each item when DMS DI•DO selection and input fields are activated.
 Device type : DI or DO
 Short name – Input short name of the device.
 Full name – Input full name of the device.
 Minimum value / Maximum value – MIN value is fixed as OFF and MAX
value is fixed as ON.
5
Click [Save].
 After the saving is complete, DMS DI•DO setting page with all inactivated
items will appear.
 If you press [Cancel], webpage will refresh and it goes back to the state
before the modification.
E-40
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 40
2019-05-15 오후 3:57:10
PIM Setting
1
Click [System Settings]  [ Tracking] when DMS2.5 web
page menu screen appears.
2
Click [Setting] which is next to PIM of device list.
 Enter administrator’s password and then click [OK].
3
Click [Edit] which is on the bottom of PIM setting page.
 [Edit] will change to [Cancel].
4
Select a field you want to change.
 Meter Value ( 0~999999.9, to one decimal place)
 Meter Type / Pulse rate
- Electricity (1~10000)
- Water (1~10000)
- Gas (0.001~10, to three decimal places)
 Channel Status
 Time Setting
 PIM Password (Number)
 You should tick the check box of the channel you want
to change.
5
Click the check boxes to select the channel applying for the setting.
6
Click [Save].
 If you press [Cancel], webpage will refresh and it goes
back to the state before the modification.
E-41
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 41
2019-05-15 오후 3:57:10
Setting the Power Distribution
 When doing power distribution, set SIM/PIM channel for each
indoor unit.
Channel Setting by Indoor Unit
1
Click [EHP Power Consumption Inspection]  [Channel
setting by indoor unit] when DMS2.5 web page menu
screen appears.
2
Click [Edit] when the setting channel by indoor unit screen
appears.
3
Check the address and channel information of SIM/PIM which
is connected to watt-hour meter.
 If 0~7 SIM/PIM units execute tracking, it will be displayed
as 16~23 in DMS2.5.
4
Check the information of indoor/outdoor unit which is
connected to watt-hour meter.
5
Check the SIM/PIM channel(watt-hour meter) information of
indoor/outdoor unit.
Y
ou can set the channel when SIM/PIM is installed in
DMS2.5.
W
hen bringing indoor unit’s power from outdoor unit, set
the ‘Outdoor unit SIM channel’ information only.
(‘Outdoor unit SIM channel’ is referring to watt-hour
meter which is connected to outdoor unit.)
W
hen bringing indoor unit’s power from the other device,
not from outdoor unit, set the ‘Outdoor unit SIM channel’
and ‘Indoor unit SIM channel’ information.
(‘Indoor unit SIM channel’ is referring to watt-hour meter
which is connected to indoor unit.)
 Power distribution will be executed automatically. The user
does not need to check the value of watt-hour meter.
 The maximum number of SIM channels for an outdoor
unit is 4.
E-42
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 42
2019-05-15 오후 3:57:10
6
Check the virtual channel information of indoor/outdoor unit.
 To execute power distribution without SIM/PIM, you should set virtual channel.
 When bringing indoor unit’s power from outdoor unit, set the ‘Outdoor unit virtual
channel’ information only.
(‘Outdoor unit virtual channel’ is referring to watt-hour meter which is connected
to outdoor unit.)
 When bringing indoor unit’s power from the other device, not from outdoor unit,
set the ‘Outdoor unit virtual channel’ and ‘Indoor unit virtual channel’ information.
(‘Indoor unit virtual channel’ is referring to watt-hour meter which is connected
to indoor unit.)
 The number of virtual channel varies depending on the number of outdoor unit.
 To execute power distribution, you need to check watt-hour meter value manually.
 Power distribution using SIM/PIM is more accurate than using indoor/outdoor unit
virtual channel. Therefore, it is recommended to execute power distribution using
SIM/PIM.
7
Set indoor unit to execute power distribution.
 If you do not set the watt-hour meter information, the power distribution result of
the indoor unit will be displayed as ‘0’.
8
Click [Save].
 Set channel information will be saved in DMS2.5.
 If you do not click [Save], changed setting will not be saved.
 Information of watt-hour meter connected to indoor/outdoor unit should be accurate.
If the watt-hour meter information is not accurate when you set channel information
of indoor unit, error may occur in the power distribution result.
 You should set SIM/PIM channel information in the indoor unit if you want to execute
power distribution using SIM/PIM. If not, it means that you do not execute power
distribution.
In this case, the power distribution result of the indoor unit will be ‘0’.
 If the information of watt-hour meter connected to indoor/outdoor unit is changed,
consult with installation engineer.
 DMS2.5 executes power distribution based on set information.
E-43
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 43
2019-05-15 오후 3:57:10
Appendix
IP Terminology

D
MS2.5 needs IP address to contact other computers.
1. Public IP
1-1. Static IP
1-2. Dynamic IP
2. Private IP
2-1. Static IP
2-2. Dynamic IP
1. Public IP : Ordinary IP used to connect internet is called
public IP.
1-1. Static IP : Static IP is a number that is assigned to a
computer by an Internet service provider
(ISP) to be its permanent address on the
Internet.
1-2. Dynamic IP : Dynamic IP is a number, which changes
every time when computer or model has
restarted.
2. P
rivate IP : This is a local IP which can not be used for
internet connection. If you share internet
connection through router, internet sharing
software or, through OS, you may check the
Client IP and they will be similar to below
number system.
10.0.0.0 ~ 10.255.255.255,
172.16.0.0 ~ 172.31.255.255,
192.168.0.0 ~ 192.168.255.255
2-1. Static IP : Designated IP assigned by user.
2-2. Dynamic IP : User sets up to obtain their IP
automatically.
E-44
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 44
2019-05-15 오후 3:57:10
Examples of DMS2.5 Installation with DSL
Local Management without External Control : Use Private IP
 Direct connection between DMS2.5 and computer or controller
DMS2.5
Computer
Cross cable
Private IP : 192.168.0.100
Private IP : 192.168.0.1
(Mount separate LAN card)
 Direct connection between DMS2.5 and computer or controller through HUB
HUB
Computer
DMS2.5
Private IP :
192.168.0.100
Private IP : 192.168.0.1
(Mount separate LAN card)
E-45
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 45
2019-05-15 오후 3:57:10
Appendix (Continued)
Initial Connection Error (for Private IP)
Several DMS2.5s are Connected to the Same Network
Computer
DMS2.5 ①
Initial IP : 192.168.0.100
Computer cannot
distinguish which DMS2.5
has 192.168.0.100 IP.
DMS2.5 ②
Initial IP : 192.168.0.100
DMS2.5 ③
Initial IP : 192.168.0.100
DMS2.5 ④
Initial IP : 192.168.0.100
In factory setting, all IP of DMS2.5 is same. Therefore, if you connect several
DMS2.5 to the same network, the computer cannot distinguish which DMS2.5 has
192.168.0.100 IP address.
Solution
-Connect only 1 DMS2.5 to the same network.
-Connect the power to only one DMS2.5 you want to use and cut the power for the
rest of DMS2.5.
-Disconnect from the network and set the IP again per each DMS2.5.
Then connect to the network again.
E-46
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 46
2019-05-15 오후 3:57:11
BACnet Gateway setting
System Architecture
BMS system
Internet
BMS Engineering
SAMSUNG Engineering
BACnet Gateway
OnOff
controller
PM 05:45
Touch Centralized Controller
Control &
Monitoring
RS 485
Schedule
Settings
Touch
Centralized
controller
Outdoor
Unit
Max 256 Indoor units
(DVM Series)
 Connecting outdoor units and BACnet Gateway
- You can control up to 80 outdoor units and 256 indoor units using BACnet Gateway.
 Each communication channel of BACnet Gateway can be connected with 16 outdoor units.
 T he maximum number of indoor units (including ERV and MCU) that can be connected to
each communication channel of BACnet Gateway RS485 is 128.
- The more outdoor units are connected, the longer time takes for tracking. (Max. 30 minutes)

For devices that support new communication, you must set the communication mode of
the channel to 'NEW' from 'System settings  Tracking' menu. Set of Indoor/outdoor units,
with conventional communication type, cannot be connected to BACnet Gateway with new
communication.

When setting communication channel mode as ‘NEW’, the address of virtual centralized
control will be assigned.
Channel 0: Virtual OnOff controller 11, Channel 1: Virtual OnOff controller 12,
Channel 2: Virtual OnOff controller 13, Channel 3: Virtual OnOff controller 14,
Channel 4: Virtual OnOff controller 15
E-47
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 47
2019-05-15 오후 3:57:11
BACnet Gateway setting (Continued)
Compatible Devices
No
Devices
Model
Note
Outdoor unit: DVM S HR, DVM S HP,
DVM ECO, DVM S WATER, DVM S
Cooling Only
Indoor unit: Models that can be
connected with above outdoor units
You should check that your indoor unit
supports BACnet Gateway. (Refer to
BACnet point list.)
MCM-A202DN, MCM-A300N
OnOff controller: Centralized controller
1
Indoor Unit
Outdoor Unit
2
OnOff
controller/
Touch
Centralized
controller
3
SIM
MIM-B12N
Needed for EHP power distribution
4
PIM
MIM-B16N
Needed for EHP power distribution
RS485 comm. type
Connected with SIM
Needed for power distribution
( Please consult Samsung for compatible
power meters)
Pulse type
Connected with PIM
Pulse Width: 20~400(ms)
Pulse: 1~10000(Wh/Pulse)
5*
Watt-hour
Meter
 Products with ‘* ’ are not Samsung products and must be purchased separately.
(Only selected power meters may be used for protocol compatibility issues.)
 Samsung is not responsible for BMS engineering which creates each device and objects.
For further directions regarding on BMS engineering, consult with specialized BMS related vendor.
E-48
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 48
2019-05-15 오후 3:57:11
Maximum Devices Attachable
Devices
Max.
Note
Indoor Unit
256
Tracking error occurs if exceeded
The maximum number of indoor units (including
ERV and MCU) that can be connected to each
communication channel is 128.
OnOff
controller/
Touch
Centralized
controller
75
Must not exceed 15 units per each RS485
communication terminal
Outdoor unit
80
Must not exceed 16 units per each RS485
communication terminal
SIM/PIM
8
Watt-hour
Meter
64
Maximum 8 units can be connected to 1 SIM/PIM.

The sum of OnOff controller, touch centralized controller, and SIM/PIM interface
module that can be connected to each communication channel should be 15 or less.
E-49
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 49
2019-05-15 오후 3:57:11
BACnet Gateway setting (Continued)
Setting the BACnet Gateway
BACnet Gateway Connection and Login
1
Click internet explorer icon(
2
When internet explorer window appears, enter IP address
(https://192.168.0.100) on the address bar then press
[ENTER].
3
If it is the first time to access BACnet Gateway, “ Install
Microsoft Silverlight” message will appear.
 If the Microsoft Silverlight has already been installed, the
above message will not appear.
4
Click [Run] button and continue installation.
After installation, access BACnet Gateway again.
) twice on your computer.
Silverlight operates normally with Windows 7 or later
version. It may not operate normally with previous version
of Windows.
5
Enter ID and password when BACnet Gateway main web
page appears, Then click [LOGIN].
 If you use accounts with general authorization level to
login, you cannot use the BACnet Gateway settings.
 Depending on authorization level set by the
administrator, access to some functions may be
restricted.
 You can change authorization level settings from
System settings  User authorization management.
 To use the BACnet Gateway functions, you must login
with the ID that is included in administration group.
Factory default BACnet Gateway ID is ‘admin’ and
password is ‘ac0530’.
Note
 Only authorized users can access web page.
C
onnection speed may slow down. Fewer than 5
concurrent users are recommended.
B
ACnet Gateway manager should change ID and
password for security and management.
 L ogout: If you want to logout, click [LOGOUT] on the
top of the menu. BACnet Gateway will be ended.
E-50
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 50
2019-05-15 오후 3:57:11

If you use accounts with authorization level lower than
management group or accounts with general authorization
level, you cannot access BACnet Gateway settings.

If you cannot access BACnet Gateway, consult the manager.
6
If you login successfully, 'Control and Monitoring' screen
will appear.
Click [System Setting]➔[BACnet configuration] menu to
switch to BACnet Gateway.

If you use accounts with authorization level lower
than management group or accounts with general
authorization level, BACnet configuration will not be
displayed on the menu.

If the BACnet configuration menu does not appear,
consult the manager.
7
If you access BACnet Gateway, 'Device Configuration'
screen will appear initially.
 If you click [DMS2.5 Connect] button, screen will be
switched to initial screen.
E-51
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 51
2019-05-15 오후 3:57:11
BACnet Gateway setting (Continued)
Reading EHP Watt-hour Meter
Setting and checking watt-hour meter
1
Click [System and Checking Watt-hour meter].
 You can change settings on watt-hour meter only when SIM/PIM interface
module is connected.
2
Click [Edit] from the 'Setting and checking Watt-hour meter' screen.
 CT proportion is set to ‘1’ as factory default value.
3
Set the [Name] and [CT proportion] for the watt-hour meter.
 You can use maximum 16 letters for name and only available special characters
are “.”, ”,”, ”_”, ”-“, and “space”.
 Value for CT proportion should be integer between range of 1 ~ 5000.
4
Click [Save].
 CT proportion value will be saved to the BACnet Gateway.
 If you do not click [Save] changed setting will not be saved.
5
Watt-hour meter value will display the actual value of electricity on the
corresponding watt-hour meter. Value will be updated automatically.
When using CT watt-hour meter, be careful that there can be difference with
actual power consumption as much as CT ratio error.
E-52
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 52
2019-05-15 오후 3:57:11
Monthly baseline setting
1
Click [System and Checking Watt-hour meter].
2
Click [Edit] from the ‘Monthly baseline setting’ screen.
 You can make changes when list box enables.
3
Set the Monthly baseline setting.
 You can select from 1 ~ 31.
 If you select the last day of the month, it will automatically set the last day of
corresponding month as baseline.
Ex) Last day of February: 28th or 29th
 Power consumption is calculated for a month before monthly baseline.
Ex) Monthly baseline: 28th
Today: 19th Nov.
Time period for power consumption and operation: 29th Sep. ~ 28th Oct.
4
Click [Save].
 Changed settings will be saved to the BACnet Gateway.
 If you do not click [Save] changed setting will not be saved.
Period setting
1
Click [System and Checking Watt-hour meter].
2
Click [Edit] from the ‘Period setting’ screen.
 You can select checkbox to set period in daily or monthly unit.
 If you select daily period setting, text box will be enabled and you can enter
the period in daily unit.
 If you select monthly period setting, you can select the period in monthly unit.
3
Set the period
 If you set period in daily unit, you can set up to maximum 90 days.
 If you set period in monthly unit, you can set up to maximum 1 months.
4
Click [Save].
 Changed setting will be saved to BACnet Gateway.
 If you do not click [Save], changed setting will not be saved.
E-53
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 53
2019-05-15 오후 3:57:12
BACnet Gateway setting (Continued)
System Settings
 You can set and check information about BACnet Gateway installation and operation.
BACnet Gateway network information
1
Click [System Settings].
2
Click [Edit] from the ‘BACnet network information’ section.
3
When text boxes of IP, Subnet mask, Default gateway, DNS server, BBMD IP, BBMD
PORT, Network No., and BACnet PORT are enabled, enter the address values for
each item.
 15 letters can be entered for each item.
 Each item should match with the network address form.
 You can enter from 1 to 40 for Network No.
 If you want to use multiple BACnet Gateway in the same network, you should set
up “Network No.” differently.
 You can edit BBMD PORT. You can enter from 0 to 65535.
 You can edit BACnet PORT. You can enter from 0 to 65535.
4
Click [Save] button on the ‘BACnet network information’ section.
5
When the pop-up window appears, click [OK].
6
If you click [OK], current internet explorer will be closed. Then you may run the
web browser again and access BACnet Gateway by entering the IP set and saved
manually.
Default value of BACnet PORT is 47808.
Check the communication with external BACnet device when changing BACnet PORT.
Set default value of BBMD PORT when not using BBMD function.
Default value of BBMD PORT is 0 (Not used).
Check the communication with external BACnet device when using BBMD function.
Local network does not work when changing BBMD PORT.
Default value of network number is 9.
Set the network number that is not repeated when communicating externally.
E-54
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 54
2019-05-15 오후 3:57:12
BACnet gateway information and initialization
1
Click [System Settings].
2
You can check the basic BACnet gateway information
from 'BACnet gateway information' section.
3
Click [Edit] from the ‘BACnet gateway information’ section.
4
If you want to initialize ‘Recipient_list’, Check and click
[Save].
5
When the pop-up window appears, click [OK]. BACnet
Gateway will restart and the system will initialize
‘Recipient_list’.
BACnet point provision type
After updating the DMS firmware, you can select a BACnet point provision type
to keep the compatibility of Instance Numbers between existing BACnet devices.
Depending on the selected BACnet point provision type, the point list for each
device provided by the BACnet Gateway varies. In addition, because the Instance
Numbers vary for each device, you need to be careful when setting them. You can
check the points for each provision type by referring to the BACnet point list.
1
Click [System Settings].
2
Click [Edit] in the ‘BACnet point provision type’ section.
3
Select one of the following BACnet point provision types:
- Basic: Reflects the default points.
- Advanced: Reflects updated points.
4
Click [Save] in the ‘BACnet point provision type’ section.
5
When the “This task requires a restart of the DMS. The
BACnet point list may vary depending on the selected
provision type. Do you want to continue?” message
appears, click [OK].
6
When you click [OK], the current web browser is closed.
After the DMS reboots, BACnet points are provided
according to the provision type you selected.
E-55
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 55
2019-05-15 오후 3:57:12
BACnet Gateway setting (Continued)
Device Configuration
Checking device information
1
Click one of the Object ID from 'Object ID' column.
Detail information of the selected device will be displayed in device information.
2
Analog data of the selected device will be displayed in Analog data.
 Object ID: Displays ID of the corresponding object.
 Type: Displays type of the corresponding object.
- AI: Input (Read Only)
- AO: Output (Read/Write)
- AV: Value (Read/Write)
 Object Name: Displays the name of the corresponding object.
 Value: Displays the current value of the corresponding object.
- Unit will be displayed between [ ].
3
Binary data of the selected device will be displayed in Binary data.
 Object ID: Displays ID of the corresponding object.
 Type: Displays type of the corresponding object.
- BI: Input (Read Only)
- BO: Output (Read/Write)
- BV: Value (Read/Write)
 Object Name: Displays the name of the corresponding object.
 Value: Displays the current value of the corresponding object.
- It will be displayed either On or Off
4
Multi-state Data of the selected device will be displayed in Multi-state data.
 Object ID: Displays ID of the corresponding object.
 Type: Displays type of the corresponding object.
- MI: Input (Read Only)
- MO: Output (Read/Write)
- MV: Value (Read/Write)
 Object Name: Displays the name of the corresponding object.
 Value: Displays the current value of the corresponding object.
Note
Please refer to BACnet Point List to check the device configuration data for each
device (Refer to page 62~73).
E-56
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 56
2019-05-15 오후 3:57:12
BACnet Protocol Implementation Conformance Statement
Date:
2017. 08. 31
Vendor Name:
Samsung Electronics Co., Ltd.
Product Name:
DMS BACnet Gateway
Product Model Number:
MIM-B17BN, MIM-B17BNDZ
Application Software Version: 1.20 Firmware Revision: 1.35
BACnet Protocol Revision: 12
Product Description:
This product supports BACnet/IP and provide functions to monitor and control status of
air conditionerss.
BACnet Standardized Device Profile (Annex L):
 BACnet Operator Workstation (B-OWS)
 BACnet Advanced Operator Workstation (B-AWS)
 BACnet Operator Display (B-OD)
 BACnet Building Controller (B-BC)
 BACnet Advanced Application Controller (B-AAC)
 BACnet Application Specific Controller (B-ASC)
 BACnet Smart Sensor (B-SS)
 BACnet Smart Actuator (B-SA)
List all BACnet Interoperability Building Blocks Supported (Annex K):
SUPPORTED
BIBBS
DS-RP-A
DS-RP-B
DS-RPM-A
DS-RPM-B
DS-RPC-A
DS-RPC-B
DS-WP-A
Data DS-WP-B
Sharing DS-WPM-A
DS-WPM-B
DS-COV-A
DS-COV-B
DS-COVP-A
DS-COVP-B
DS-COVU-A
DS-COVU-B
BIBB NAME
Data Sharing-ReadProperty-A
Data Sharing-ReadProperty-B
Data Sharing-ReadPropertyMultiple-A
Data Sharing-ReadPropertyMultiple-B
Data Sharing-ReadPropertyConditional-A
Data Sharing-ReadPropertyConditional-B
Data Sharing-WriteProperty-A
Data Sharing-WriteProperty-B
Data Sharing-WritePropertyMultiple-A
Data Sharing-WritePropertyMultiple-B
DataSharing-COV-A
DataSharing-COV-B
DataSharing-COVP-A
DataSharing-COVP-B
DataSharing-COV-Unsolicited-A
DataSharing-COV-Unsolicited-B
SUPPORTED REMARKS
















E-57
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 57
2019-05-15 오후 3:57:12
BACnet Gateway setting (Continued)
SUPPORTED
BIBBS
AE-N-A
AE-N-I-B
AE-N-E-B
AE-ACK-A
AE-ACK-B
Alarm and AE-ASUM-A
Event
AE-ASUM-A
Management AE-ESUM-A
AE-ESUM-B
AE-INFO-A
AE-INFO-B
AE-LS-A
AE-LS-B
SCHED-A
Scheduling SCHED-I-B
SCHED-E-B
T-VMT-A
T-VMT-I-B
T-VMT-E-B
T-ATR-A
T-ATR-B
Trending
T-VMMV-A
T-VMMV-I-B
T-VMMV-E-B
T-AMVR-A
T-AMVR-B
DM-DDB-A
DM-DDB-B
DM-DOB-A
DM-DOB-B
DM-DCC-A
DM-DCC-B
DM-TM-A
Device and
DM-TM-B
Network
DM-TS-A
Management
DM-TS-B
DM-UTC-A
DM-UTC-B
DM-RD-A
DM-RD-B
DM-BR-A
DM-BR-B
BIBB NAME
Alarm&Event-Notification-A
Alarm&Event-Notification Internal-B
Alarm&Event-Notification External-B
Alarm&Event-ACK-A
Alarm&Event-ACK-B
Alarm&Event-Summary-A
Alarm&Event-Summary-B
Alarm&Event-Enrollment Summary-A
Alarm&Event-Enrollment Summary-B
Alarm&Event-Information-A
Alarm&Event-Information-B
Alarm&Event-LifeSafety-A
Alarm&Event-LifeSafety-B
Scheduling-A
Scheduling-Internal-B
Scheduling-External-B
Viewing and Modifying Trends-A
Viewing and Modifying Trends Internal-B
Viewing and Modifying Trends External-B
Automated Trend Retrieval-A
Automated Trend Retrieval-B
Viewing and Modifying Multiple Values-A
View and Modifying Multiple Values Internal-B
View and Modifying Multiple Values External-B
Automated Multiple Value Retrieval-A
Automated Multiple Value Retrieval-B
Dynamic Device Binding-A
Dynamic Device Binding-B
Dynamic Object Binding-A
Dynamic Object Binding-B
DeviceCommunicationControl-A
DeviceCommunicationControl-B
Text Message-A
Text Message-B
Time Synchronization-A
Time Synchronization-B
UTCTime Synchronization-A
UTCTime Synchronization-B
ReinitializeDevice-A
ReinitializeDevice-B
Backup&Restore-A
Backup&Restore-B
SUPPORTED REMARKS










































E-58
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 58
2019-05-15 오후 3:57:12
SUPPORTED
BIBBS
DM-R-A
DM-R-B
DM-LM-A
DM-LM-B
DM-OCD-A
Device and
DM-OCD-B
Network
Management DM-VT-A
DM-VT-B
NM-CE-A
NM-CE-B
NM-RC-A
NM-RC-B
BIBB NAME
SUPPORTED REMARKS
Restart-A
Restart-B
List Manipulation-A
List Manipulation-B
Object Creation & Deletion-A
Object Creation & Deletion-B
Virtual Terminal-A
Virtual Terminal-B
Connection Establishment-A
Connection Establishment-B
Router Configuration-A
Router Configuration-B












Segmentation Capability:
 Segmented requests supported Window Size
 Segmented responses supported Window Size
Standard Object Types Supported:
Object-Type
Supported
Analog Input
Analog Output
Analog Value
Binary Input
Binary Output
Binary Value
Calendar
Command
Device
Event Enrollment
File
Group
Loop
Multi-state Input
Multi-state Output








Yes










Multi-state Value
Notification Class
Program
Schedule
Dynamically
Creatable








n/a










Dynamically
Deletable








n/a










Writeable Properties
Present value
Present value
Present value
n/a
Present value
Present value
Recipient_List
E-59
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 59
2019-05-15 오후 3:57:12
BACnet Gateway setting (Continued)
Data Link Layer Options:
 BACnet IP, (Annex J)
 BACnet IP, (Annex J), Foreign Device
 ISO 8802-3, Ethernet (Clause 7)
 ANSI/ATA 878.1, 2.5 Mb. ARCNET (Clause 8)
 ANSI/ATA 878.1, RS-485 ARCNET (Clause 8), baud rate(s)
 MS/TP master (Clause 9), baud rate(s):
 MS/TP slave (Clause 9), baud rate(s):
 Point-To-Point, EIA 232 (Clause 10), baud rate(s):
 Point-To-Point, modem, (Clause 10), baud rate(s):
 LonTalk, (Clause 11), medium:
 BACnet/ZigBee (ANNEX O)
 Other:
Device Address Binding:
Is static device binding supported? (This is currently necessary for two-way communication
with MS/TP slaves and certain other devices.) Yes  No
Networking Options:
 Router, Clause 6 - List all routing configurations, e.g., ARCNET-Ethernet,
Ethernet-MS/TP, etc.
 Annex H, BACnet Tunneling Router over IP
 BACnet/IP Broadcast Management Device (BBMD)
Does the BBMD support registrations by Foreign Devices?  Yes
 No
Does the BBMD support network address translation?
 Yes
 No
Character Sets Supported:
Indicating support for multiple character sets does not imply that they can all be supported
simultaneously.
 ISO 10646 (UTF-8)
 IBM™/Microsoft™ DBCS  ISO 8859-1
 ISO 10646 (UCS-2)
 ISO 10646 (UCS-4)
 JIS 0208
If this product is a communication gateway, describe the types of non-BACnet equipment/
networks(s) that the gateway supports:
This gateway switches SAMSUNG air conditioner protocol to BACnet protocol to make
RS-485 communication possible with the air conditioners connected to gateway.
E-60
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 60
2019-05-15 오후 3:57:12
Detail Description of Object
Device
Following table shows regulation of device ID and they are created automatically.
DNET – Range
[Digit 2]
CPP – Range
[Digit 3]
INDOOR – Range
[Digit 2]
Centralized Controller
(OnOff Controller)
1~40
000~015
64
SIM/PIM
1~40
100~115
64
DMS DI/DO
1~40
300~315
64
Interface Module
(Outdoor Unit)
1~40
400~655
(16 x 16)
64
Indoor Unit, ERV, ERV Plus,
AHU kit, EHS, Fresh duct
1~40
400~655
0~63
Gateway
1~40
900
64
Item
Ex) Indoor Unit
DNET (Gateway number): 9
Indoor Unit Address: 01.01.32
Device ID: 941732
Indoor Unit Individual address
DNET (Gateway number)
9
417
32
400 + 1x16 + 1 = 417
Centralized Controller
(OnOff Controller)
address
Interface Module
(Outdoor Unit)
address
Object of device
Refer to BACnet point List
Command Priorities

­ - Supports 1 ~ 16 Priority Level
­ - Recommends 8 Priority Level
E-61
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 61
2019-05-15 오후 3:57:12
BACnet Gateway setting (Continued)
BACnet Point List
The BACnet point list varies depending on which [BACnet point provision type] is
selected in the [System Settings] menu.
There are two BACnet point provision types:
(1) Basic: Reflects the default points.
(2) Advanced: Reflects updated points.
For details, refer to the point list below.
Indoor Unit [Basic]
Single indoor unit has following point list.
Instance
Number
1
2
3
4
Object
Object
Type
Object Name
** 12
** 13
** 14
* 15
Indoor Temperature
AI AC_RoomTemp_xx_xxxxxx
Set temperature
AV AC_Temp_Set_xx_xxxxxx
Setting lower temperature limit
AV AC_Cool_LimitTemp_xx_xxxxxx
Setting upper temperature limit
AV AC_Heat_LimitTemp_xx_xxxxxx
The power value of an indoor unit after
AI AC_Baseline_kWh_xx_xxxxxx
the basic date
The number of hours usage of an
AI AC_Baseline_Minute_xx_xxxxxx
indoor unit after the basic date
Power value within period
AI AC_Period_kWh_xx_xxxxxx
The number of hours usage of an
AI AC_Period_Minute_xx_xxxxxx
indoor unit within period
Power On/Off
BV AC_Power_xx_xxxxxx
Applying lower temperature limit
BV AC_Cool_Limit_set_xx_xxxxxx
setting
Applying upper temperature limit
BV AC_Heat_Limit_set_xx_xxxxxx
setting
Filter sign status
BI AC_FilterSign_xx_xxxxxx
Filter sign reset
BO AC_FilterSign_Reset_xx_xxxxxx
Operation mode status
MV AC_Operation_Mode_xx_xxxxxx
Fan speed status
MV AC_FanSpeed_xx_xxxxxx
* 16
Air flow direction status
MV AC_FanFlow_xx_xxxxxx
** 17
Operation mode limit status
MV AC_Mode_Limit_xx_xxxxxx
5
6
7
8
** 9
10
11
** 18 Remote controller limit status
Integrated error code of both indoor
** 19 unit and outdoor unit
* 20 SPI setting
* 21 HumanSensor setting
* 22 Discharge cooling set temperature
* 23 Discharge heating set temperatrue
MV AC_Remocon_Limit_xx_xxxxxx
AI
AC_Error_Code_xx_xxxxxx
BV
BV
AV
AV
AC_SPI_xx_xxxxxx
AC_MDS_xx_xxxxxx
AC_DisCoolTemp_Set_xx_xxxxxx
AC_DisHeatTemp_Set_xx_xxxxxx
Unit
Inactive Active
Text-1 Text-2
°C
°C
°C
°C
Status value
Text-3
Text-4 Text-5
Heat
Mid
Fan Dry
High Turbo
kWh
Minute
kWh
Minute
Off
On
False
True
False
True
False
False
Auto
Auto
True
True
Cool
Low
1: None, 2: Vertical, 3: Horizon, 4: All,
5: Spot, 6: Mid, 7: Wide, 8: Swing
No
Limit
Cool
Only
Enable RC
Heat
Only
Disable Conditional
RC
RC
Refer to list of error code
False
False
°C(°F)
°C(°F)
True
True
E-62
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 62
2019-05-15 오후 3:57:12
Instance
Number
Object
Object
Type
Object Name
* 24 Discharge current temperature
AI
** 25 AC Indoor Notify
NC AC_Notify_xx_xxxxxx
AC_DisCurrentTemp_xx_xxxxxx
Unit
Status value
Inactive Active
Text-1 Text-2 Text-3 Text-4 Text-5
°C(°F)
When the error occurred, send event to list of
destination in the recipient_list. (Max : 8)
Temperature setting range can be different depending on the model and the common range is as
follows:
Auto: 18 ˚C~30 ˚C
Cool: 18 ˚C~30 ˚C
Heat: 16 ˚C~30 ˚C
Fan: Temperature cannot be adjusted
Dry: 18 ˚C~30 ˚C
(*) Mark is optionally supported. For a fresh duct, (**) mark is supported.
Indoor Unit [Advanced]
Single indoor unit has following point list.
Instance
Number
1
2
3
4
Object
Object
Type
Object Name
** 12
** 13
** 14
* 15
Indoor Temperature
AI AC_RoomTemp_xx_xxxxxx
Set temperature
AV AC_Temp_Set_xx_xxxxxx
Setting lower temperature limit
AV AC_Cool_LimitTemp_xx_xxxxxx
Setting upper temperature limit
AV AC_Heat_LimitTemp_xx_xxxxxx
The power value of an indoor unit after
AI AC_Baseline_kWh_xx_xxxxxx
the basic date
The number of hours usage of an
AI AC_Baseline_Minute_xx_xxxxxx
indoor unit after the basic date
Power value within period
AI AC_Period_kWh_xx_xxxxxx
The number of hours usage of an
AI AC_Period_Minute_xx_xxxxxx
indoor unit within period
Power On/Off
BV AC_Power_xx_xxxxxx
Applying lower temperature limit
BV AC_Cool_Limit_set_xx_xxxxxx
setting
Applying upper temperature limit
BV AC_Heat_Limit_set_xx_xxxxxx
setting
Filter sign status
BI AC_FilterSign_xx_xxxxxx
Filter sign reset
BO AC_FilterSign_Reset_xx_xxxxxx
Operation mode status
MV AC_Operation_Mode_xx_xxxxxx
Fan speed status
MV AC_FanSpeed_xx_xxxxxx
* 16
Air flow direction status
MV AC_FanFlow_xx_xxxxxx
** 17
Operation mode limit status
MV AC_Mode_Limit_xx_xxxxxx
5
6
7
8
** 9
10
11
** 18 Remote controller limit status
MV AC_Remocon_Limit_xx_xxxxxx
Unit
Inactive Active
Text-1 Text-2
°C
°C
°C
°C
Status value
Text-3
Text-4 Text-5
Heat
Mid
Fan Dry
High Turbo
kWh
Minute
kWh
Minute
Off
On
False
True
False
True
False
False
Auto
Auto
True
True
Cool
Low
1: None, 2: Vertical, 3: Horizon, 4: All,
5: Spot, 6: Mid, 7: Wide, 8: Swing
No
Limit
Enable RC
Cool
Only
Heat
Only
Disable Conditional
RC
RC
E-63
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 63
2019-05-15 오후 3:57:13
BACnet Gateway setting (Continued)
Instance
Number
Object
Integrated error code of both indoor
** 19 unit and outdoor unit
* 20 SPI setting
Object
Type
AI
* 21
* 22
* 23
* 24
*25
*26
27
28
29
30
*31
*32
BV
HumanSensor setting
BV
Discharge cooling set temperature
AV
Discharge heating set temperatrue
AV
Discharge current temperature
AI
Wind-Free
BV
MDS air-flow direction
MV
Cooling temperature upper limit
AV
Heating temperature lower limit
AV
Use of cooling temperature upper limit BV
Use of heating temperature lower limit BV
Automatic Cooling Set Temperature
AV
Automatic Heating Set Temperature
AV
*33
Comprehensive air cleanliness
*34
*35
*36
PM10.0 value
PM2.5 value
PM1.0 value
** 54 AC Indoor Notify
Object Name
AC_Error_Code_xx_xxxxxx
Unit
Inactive Active
Text-1 Text-2
Status value
Text-3
Text-4 Text-5
Refer to list of error code
False
True
AC_MDS_xx_xxxxxx
False
True
AC_DisCoolTemp_Set_xx_xxxxxx °C(°F)
AC_DisHeatTemp_Set_xx_xxxxxx °C(°F)
AC_DisCurrentTemp_xx_xxxxxx
°C(°F)
AC_WindFree_xx_xxxxxx
False
True
AC_MDS_Opt_Direction_xx_xxxxx Indirect direct
AC_Cool_Upper_LimitTemp_xx_xxxxx °C(°F)
AC_Heat_Lower_LimitTemp_xx_xxxxx °C(°F)
AC_Cool_Upper_Limit_set_xx_xxxxx False
True
AC_Heat_Lower_Limit_set_xx_xxxxx False
True
AC_DualSetPoint_CoolTemp_xx_xxxxx °C(°F)
AC_DualSetPoint_HeatTemp_xx_xxxxx °C(°F)
1: None, 2: Level 1 (Good),
3: Level 2 (Moderate), 4: Level 3 (Bad),
MI AC_Air_Total_Clean_Level_xx_xxxxx 5: Level 4 (Very bad), 6: Level 5 (Very very bad),
7: Level 6 (Very very very bad)
AI AC_Dust_Sensor_PM_10_0
µg/m3
AI AC_Dust_Sensor_PM_2_5
µg/m3
AI AC_Dust_Sensor_PM_1_0
µg/m3
When
the error occurred, send event to list of
NC AC_Notify_xx_xxxxxx
destination in the recipient_list. (Max : 8)
AC_SPI_xx_xxxxxx
Of the BACnet points, Reserved points (Instance Numbers 37 to 53) are points for future use.
Temperature setting range can be different depending on the model and the common range is as
follows:
Auto: 18 ˚C~30 ˚C
Cool: 18 ˚C~30 ˚C
Heat: 16 ˚C~30 ˚C
Fan: Temperature cannot be adjusted
Dry: 18 ˚C~30 ˚C
(*) Mark is optionally supported. For a fresh duct, (**) mark is supported.
E-64
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 64
2019-05-15 오후 3:57:13
ext-5
),
bad),
list of
: 8)
is as
AHU Kit [Basic]
Single AHU unit has following point list.
Instance
Number
Object
1
2
12
13
14
Indoor Temperature
Set temperature
Setting lower temperature
limit
Setting upper temperature
limit
The power value of an indoor
unit after the basic date
The number of hours usage of
an indoor unit after the basic
date
Power value within period
The number of hours usage of
an indoor unit within period
Power On/Off
Applying lower temperature
limit setting
Applying upper temperature
limit setting
Filter sign status
Filter sign reset
Operation mode status
15
Operation mode limit status
16
Remote controller limit status
3
4
5
6
7
8
9
10
11
Object
Type
Object Name
AI AHU_RoomTemp_xx_xxxxxx
AV AHU_Temp_Set_xx_xxxxxx
Unit
Inactive Active
Text-1 Text-2
°C
°C
AV AHU_Cool_LimitTemp_xx_xxxxxx
°C
AV AHU_Heat_LimitTemp_xx_xxxxxx
°C
AI
AHU_Baseline_kWh_xx_xxxxxx
AI
AHU_Baseline_Minute_xx_xxxxxx Minute
AI
AHU_Period_kWh_xx_xxxxxx
AI
AHU_Period_Minute_xx_xxxxxx
Status value
Text-3 Text-4 Text-5
kWh
kWh
Minute
BV AHU_Power_xx_xxxxxx
Off
On
BV AHU_Cool_Limit_set_xx_xxxxxx
False
True
BV AHU_Heat_Limit_set_xx_xxxxxx
False
BI AHU_FilterSign_xx_xxxxxx
False
BO AHU_FilterSign_Reset_xx_xxxxxx False
MV AHU_Operation_Mode_xx_xxxxxx Auto
No
MV AHU_Mode_Limit_xx_xxxxxx
Limit
Enable
MV AHU_Remocon_Limit_xx_xxxxxx
RC
True
True
True
Cool Heat Fan Dry
Cool Heat
Only Only
Disable Conditional
RC
RC
Integrated error code of both
AI AHU_Error_Code_xx_xxxxxx
Refer to list of error code
indoor unit and outdoor unit
Discharge cooling set
* 18
AV AHU_DisCoolSetTemp_xx_xxxxxx
°C
temperature
Discharge heating set
* 19
AV AHU_DisHeatSetTemp_xx_xxxxxx °C
temperature
* 20 Discharge current temperature AI AHU_Dis_CurrentTemp_xx_xxxxxx °C
* 21 Humidification setting
BV AHU_Humidification_xx_xxxxxx
Off
On
* 22 Outdoor air intake setting
BV AHU_OAIntake_xx_xxxxxx
Off
On
* 23 Outdoor cooling setting
BV AHU_OutdoorCool_xx_xxxxxx
Off
On
* 24 Fan speed status
MV AHU_FanSpeed_xx_xxxxxx
Low Mid
High
* 25 Set humidity status
MV AHU_SetHumidity_xx_xxxxxx
Low Mid
High
* 26 Current humidity status
MI AHU_CurrentHumidity_xx_xxxxxx Low Mid
High
When the error occurred, send
event to list of destination in the
27 AHU Notify
NC AHU_Notify_xx_xxxxxx
recipient_list. (Max : 8)
(*) Mark is optionally supported.
17
E-65
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 65
2019-05-15 오후 3:57:13
BACnet Gateway setting (Continued)
AHU Kit [Advanced]
Single AHU unit has following point list.
Instance
Number
Object
1
2
12
13
14
Indoor Temperature
Set temperature
Setting lower temperature
limit
Setting upper temperature
limit
The power value of an indoor
unit after the basic date
The number of hours usage of
an indoor unit after the basic
date
Power value within period
The number of hours usage of
an indoor unit within period
Power On/Off
Applying lower temperature
limit setting
Applying upper temperature
limit setting
Filter sign status
Filter sign reset
Operation mode status
15
Operation mode limit status
16
Remote controller limit status
3
4
5
6
7
8
9
10
11
17
* 18
* 19
* 20
* 21
* 22
* 23
* 24
* 25
* 26
Object
Type
Object Name
AI AHU_RoomTemp_xx_xxxxxx
AV AHU_Temp_Set_xx_xxxxxx
Unit
Inactive Active
Text-1 Text-2
°C
°C
AV AHU_Cool_LimitTemp_xx_xxxxxx
°C
AV AHU_Heat_LimitTemp_xx_xxxxxx
°C
AI
AHU_Baseline_kWh_xx_xxxxxx
AI
AHU_Baseline_Minute_xx_xxxxxx Minute
AI
AHU_Period_kWh_xx_xxxxxx
AI
AHU_Period_Minute_xx_xxxxxx
Status value
Text-3 Text-4 Text-5
kWh
kWh
Minute
BV AHU_Power_xx_xxxxxx
Off
On
BV AHU_Cool_Limit_set_xx_xxxxxx
False
True
BV AHU_Heat_Limit_set_xx_xxxxxx
False
True
BI AHU_FilterSign_xx_xxxxxx
False
BO AHU_FilterSign_Reset_xx_xxxxxx False
MV AHU_Operation_Mode_xx_xxxxxx Auto
No
MV AHU_Mode_Limit_xx_xxxxxx
Limit
Enable
MV AHU_Remocon_Limit_xx_xxxxxx
RC
True
True
Cool Heat Fan Dry
Cool Heat
Only Only
Disable Conditional
RC
RC
Integrated error code of both
AI AHU_Error_Code_xx_xxxxxx
Refer to list of error code
indoor unit and outdoor unit
Discharge cooling set
AV AHU_DisCoolSetTemp_xx_xxxxxx
°C
temperature
Discharge heating set
AV AHU_DisHeatSetTemp_xx_xxxxxx °C
temperature
Discharge current temperature AI AHU_Dis_CurrentTemp_xx_xxxxxx °C
Humidification setting
BV AHU_Humidification_xx_xxxxxx
Off
On
Outdoor air intake setting
BV AHU_OAIntake_xx_xxxxxx
Off
On
Outdoor cooling setting
BV AHU_OutdoorCool_xx_xxxxxx
Off
On
Fan speed status
MV AHU_FanSpeed_xx_xxxxxx
Low Mid
High
Set humidity status
MV AHU_SetHumidity_xx_xxxxxx
Low Mid
High
Current humidity status
MI AHU_CurrentHumidity_xx_xxxxxx Low Mid
High
E-66
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 66
2019-05-15 오후 3:57:13
Instance
Number
27
28
29
30
*31
*32
33
Object
Cooling temperature upper
limit
Heating temperature lower
limit
Use of cooling temperature
upper limit
Use of heating temperature
lower limit
Automatic Cooling Set
Temperature
Automatic Heating Set
Temperature
AHU Notify
Object
Type
Object Name
Unit
Inactive Active
Text-1 Text-2
Status value
Text-3 Text-4 Text-5
AV AHU_Cool_Upper_LimitTemp_xx_xxxxx °C(°F)
AV AHU_Heat_Lower_LimitTemp_xx_xxxxx °C(°F)
BV AHU_Cool_Upper_Limit_set_xx_xxxxx False True
BV AHU_Heat_Lower_Limit_set_xx_xxxxx False True
AV AHU_DualSetPoint_CoolTemp_xx_xxxxx °C(°F)
AV AHU_DualSetPoint_HeatTemp_xx_xxxxx °C(°F)
NC AHU_Notify_xx_xxxxxx
When the error occurred, send
event to list of destination in the
recipient_list. (Max : 8)
(*) Mark is optionally supported.
E-67
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 67
2019-05-15 오후 3:57:13
BACnet Gateway setting (Continued)
EHS [Basic]
Single EHS Unit has following point list.
Instance
Number
Object Name
Unit
Inactive Active
Status value
Text-1 Text-2
°C
Text-3
1
Room temperature
AI
EHS_RoomTemp_xx_xxxxxx
2
Set temperature
AV
EHS_Temp_Set_xx_xxxxxx
°C
3
Set temperature of water out
AV
EHS_WaterOutTemp_Set_xx_xxxxxx
°C
4
Set temperature of hot water
AV
EHS_HotWaterTemp_Set_xx_xxxxxx
°C
5
Setting lower temperature limit
AV
EHS_Cool_LimitTemp_xx_xxxxxx
°C
6
Setting upper temperature limit
AV
EHS_Heat_LimitTemp_xx_xxxxxx
°C
7
8
9
10
AV
AV
AV
AI
EHS_WOCoolLimitTemp_xx_xxxxxx
EHS_WOHeatLimitTemp_xx_xxxxxx
EHS_WTHeatlLimitTemp_xx_xxxxxx
EHS_Baseline_kWh_xx_xxxxxx
°C
°C
°C
AI
EHS_Baseline_Minute_xx_xxxxxx
AI
EHS_Period_kWh_xx_xxxxxx
AI
EHS_Period_Minute_xx_xxxxxx
14
15
16
17
18
19
Lower temperature limit for water out
Upper temperature limit for water out
Upper temperature limit for hot water
The power value after the basic date
The number of hours usage of an
indoor unit after the basic date
Power value within period
The number of hours usage of an
indoor unit within period
Current temperature of water out
Current temperature of hot water
Displayed temperature type
Thermostat usage
Outing
Power On/Off
AI
AI
BI
BI
BI
BV
EHS_WOCurrentTemp_xx_xxxxxx
EHS_HotWaterTemp_xx_xxxxxx
EHS_ControlTempType_xx_xxxxxx
EHS_Thermostat_xx_xxxxxx
EHS_GoOut_xx_xxxxxx
EHS_Power_xx_xxxxxx
Room WaterOut
False
True
Off
On
Off
On
20
Setting lower temperature limit
BV
EHS_Cool_LimitTemp_Set_xx_xxxxxx
False
True
21
Setting upper temperature limit
BV
EHS_Heat_LimitTemp_Set_xx_xxxxxx
False
True
22
EHS_WOCoolLimitFlag_xx_xxxxxx
False
True
EHS_WOHeatLimitFlag_xx_xxxxxx
False
True
24
25
26
27
Apply lower temperature limit for BV
water out
Apply upper temperature limit for BV
water out
Apply upper temperature limit for hot water BV
On/Off status of hot water mode
BV
Status of quiet operation
BV
Operation mode status
MV
EHS_WTHeatLimitFlag_xx_xxxxxx
EHS_HotWater_Power_xx_xxxxxx
EHS_Sleep_xx_xxxxxx
EHS_Operation_Mode_xx_xxxxxx
False
Off
Off
Auto
28
Operation mode limit status
MV
EHS_Mode_Limit_xx_xxxxxx
29
Remote controller limit status
MV
EHS_Remocon_Limit_xx_xxxxxx
30
31
Status of hot water operation mode
MV
Integrated error code of both indoor AI
unit and outdoor unit
EHS_Error_Code_xx_xxxxxx
32
EHS notifiy
EHS_Notify_xx_xxxxxx
11
12
13
23
E-68
Object
Type
Object
NC
EHS_HotWater_Mode_xx_xxxxxx
Text-4
Use when displayed temperature type
is set to 'Room'.
Use when displayed temperature type
is set to 'WaterOut'.
Use when displayed temperature type
is set to 'Room'.
Use when displayed temperature type
is set to 'Room'.
kWh
Minute
kWh
Minute
°C
°C
Use when displayed temperature type is set to 'Room'.
Use when displayed temperature type is set to 'Room'.
Use when displayed temperature type is set to 'WaterOut'.
Use when displayed temperature type is set to 'WaterOut'.
True
On
On
Cool
Heat
Cool
No Limit Only
Heat Only
Conditional
Enable RC Disable
RC
RC
* Force
Eco
Standard
Power
When the error occurred, send event to list
of destination in the recipient_list. (Max : 8)
Force hot water mode (* marked) will be supported later.
It is the point list of Hydro Unit and Hydro Unit HT.
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 68
2019-05-15 오후 3:57:13
EHS [Advanced]
Single EHS Unit has following point list.
Instance
Number
Object
Object
Type
Object Name
Unit
Inactive Active
Status value
Text-1 Text-2
°C
Text-3
1
Room temperature
AI
EHS_RoomTemp_xx_xxxxxx
2
Set temperature
AV
EHS_Temp_Set_xx_xxxxxx
°C
3
Set temperature of water out
AV
EHS_WaterOutTemp_Set_xx_xxxxxx
°C
4
Set temperature of hot water
AV
EHS_HotWaterTemp_Set_xx_xxxxxx
°C
5
Setting lower temperature limit
AV
EHS_Cool_LimitTemp_xx_xxxxxx
°C
6
Setting upper temperature limit
AV
EHS_Heat_LimitTemp_xx_xxxxxx
°C
7
8
9
10
AV
AV
AV
AI
EHS_WOCoolLimitTemp_xx_xxxxxx
EHS_WOHeatLimitTemp_xx_xxxxxx
EHS_WTHeatlLimitTemp_xx_xxxxxx
EHS_Baseline_kWh_xx_xxxxxx
°C
°C
°C
AI
EHS_Period_Minute_xx_xxxxxx
14
15
16
17
18
19
Lower temperature limit for water out
Upper temperature limit for water out
Upper temperature limit for hot water
The power value after the basic date
The number of hours usage of an
indoor unit after the basic date
Power value within period
The number of hours usage of an
indoor unit within period
Current temperature of water out
Current temperature of hot water
Displayed temperature type
Thermostat usage
Outing
Power On/Off
AI
AI
BI
BI
BI
BV
EHS_WOCurrentTemp_xx_xxxxxx
EHS_HotWaterTemp_xx_xxxxxx
EHS_ControlTempType_xx_xxxxxx
EHS_Thermostat_xx_xxxxxx
EHS_GoOut_xx_xxxxxx
EHS_Power_xx_xxxxxx
Room WaterOut
False
True
Off
On
Off
On
20
Setting lower temperature limit
BV
EHS_Cool_LimitTemp_Set_xx_xxxxxx
False
True
21
Setting upper temperature limit
BV
EHS_Heat_LimitTemp_Set_xx_xxxxxx
False
True
22
EHS_WOCoolLimitFlag_xx_xxxxxx
False
True
EHS_WOHeatLimitFlag_xx_xxxxxx
False
True
24
25
26
27
Apply lower temperature limit for BV
water out
Apply upper temperature limit for BV
water out
Apply upper temperature limit for hot water BV
On/Off status of hot water mode
BV
Status of quiet operation
BV
Operation mode status
MV
EHS_WTHeatLimitFlag_xx_xxxxxx
EHS_HotWater_Power_xx_xxxxxx
EHS_Sleep_xx_xxxxxx
EHS_Operation_Mode_xx_xxxxxx
False
Off
Off
Auto
28
Operation mode limit status
MV
EHS_Mode_Limit_xx_xxxxxx
29
Remote controller limit status
MV
EHS_Remocon_Limit_xx_xxxxxx
30
31
Status of hot water operation mode
MV
Integrated error code of both indoor AI
unit and outdoor unit
32
Cooling temperature upper limit
11
12
13
23
AI
EHS_Baseline_Minute_xx_xxxxxx
AI
EHS_Period_kWh_xx_xxxxxx
AV
EHS_HotWater_Mode_xx_xxxxxx
Text-4
Use when displayed temperature type
is set to 'Room'.
Use when displayed temperature type
is set to 'WaterOut'.
Use when displayed temperature type
is set to 'Room'.
Use when displayed temperature type
is set to 'Room'.
kWh
Minute
kWh
Minute
°C
°C
Use when displayed temperature type is set to 'Room'.
Use when displayed temperature type is set to 'Room'.
Use when displayed temperature type is set to 'WaterOut'.
Use when displayed temperature type is set to 'WaterOut'.
True
On
On
Cool
Heat
Cool
No Limit Only
Heat Only
Conditional
Enable RC Disable
RC
RC
* Force
Eco
Standard
Power
EHS_Error_Code_xx_xxxxxx
when the room temperature is used
EHS_Cool_Upper_LimitTemp_xx_xxxxx °C(°F) Used
as the temperature display reference
E-69
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 69
2019-05-15 오후 3:57:14
BACnet Gateway setting (Continued)
Instance
Number
Object
Type
Object
Object Name
Unit
Inactive Active
Status value
Text-1 Text-2
Text-3
Heating temperature lower limit
AV
34
AV
36
Cooling temperature upper limit,
based on water out temperature
Heating temperature lower limit,
based on water out temperature
Hot water temperature lower limit
AV
EHS_WT_Heat_Lower_LimitTemp_xx_xxxxx °C(°F)
37
Use of cooling temperature upper
limit
BV
EHS_Cool_Upper_Limit_set_xx_xxxxx
False
38
Use of heating temperature lower limit
BV
EHS_Heat_Lower_Limit_set_xx_xxxxx
False
39
Use of cooling temperature upper
limit, based on water out temperature
BV
EHS_WO_Cool_Upper_LimitFlag_xx_xxxxx
False
40
Use of heating temperature lower
limit, based on water out temperature
BV
EHS_WO_Heat_Lower_LimitFlag_xx_xxxxx
False
41
Use of hot water temperature lower
limit
BV
EHS_WT_Heat_Lower_LimitFlag_xx_xxxxx
35
42
AV
EHS notifiy
NC
Text-4
Used when the room temperature is used
as the temperature display reference
Used when the water out temperature is
EHS_WO_Cool_Upper_LimitTemp_xx_xxxxx °C(°F) used as the temperature display reference
Used when the water out temperature is
EHS_WO_Heat_Lower_LimitTemp_xx_xxxxx °C(°F) used as the temperature display reference
EHS_Heat_Lower_LimitTemp_xx_xxxxx °C(°F)
33
False
Used when the room
temperature is used as the
temperature display reference
Used when the room
True temperature is used as the
temperature display reference
Used when the water out
True temperature is used as the
temperature display reference
Used when the water out
True temperature is used as the
temperature display reference
True
True
When the error occurred, send event to list
of destination in the recipient_list. (Max : 8)
EHS_Notify_xx_xxxxxx
Force hot water mode (* marked) will be supported later.
It is the point list of Hydro Unit and Hydro Unit HT.
ERV, ERV Plus [Basic, Advanced]
Single ERV or ERV Plus unit has following point list.
Instance
Number
Object
1
Power On/Off operation
2
3
Object
Type
Object Name
Unit
Inactive Active
Text-1 Text-2
BV
ERV_Power_xx_xxxxxx
Off
On
Filter sign status
BI
ERV_FilterSign_xx_xxxxxx
False
True
Filter sign reset
BO
ERV_FilterSign_Reset_xx_xxxxxx
False
True
4
5
Operation mode status
Fan speed status
MV ERV_Operation_Mode_xx_xxxxxx
MV ERV_FanSpeed_xx_xxxxxx
6
Remote controller limit status
MV ERV_Remocon_Limit_xx_xxxxxx
7
AI
ERV_Error_Code_xx_xxxxxx
AI
ERV_Plus_Baseline_kWh_xx_xxxxxx
*9
Integrated error code of ERV unit
The power value of an ERV Plus unit
after the basic date
The number of hours usage of an
ERV Plus unit after the basic date
AI
ERV_Plus_Baseline_Minute_xx_xxxxxx Minute
*10
Power value within period
AI
ERV_Plus_Period_kWh_xx_xxxxxx
*11
The number of hours usage of an
ERV Plus unit within period
AI
ERV_Plus_Period_Minute_xx_xxxxxx
*12
ERV Plus operation mode status
MV ERV_Plus_Operation_Mode_xx_xxxxxx Auto
*8
*13
ERV Plus operation mode limit status
MV ERV_Plus_Mode_Limit_xx_xxxxxx
14
ERV Notify
NC ERV_Notify_xx_xxxxxx
Status value
Text-3
Text-4 Text-5
Auto HeatEx Bypass
Sleep
Low
High
Turbo
Enable Disable Conditional
RC
RC
RC
kWh
kWh
Minute
Cool
Heat
Off
Cool Heat Only
No Limit Only
When the error occurred, send event to list of
destination in the recipient_list. (Max : 8)
(*) Mark is optionally supported.
E-70
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 70
2019-05-15 오후 3:57:14
DVM CHILLER [Basic, Advanced]
Single DVM CHILLER Unit has following point list.
Instance
Number
Object
Object
Type
Object Name
Unit
Inactive Active
Text-1 Text-2
1
Chilled Water Temperature
AI
MC_WaterTemp_xx_xxxxxx
°C/F
2
Set temperature
AV
MC_WaterTemp_Set_xx_xxxxxx
°C/F
3
AV
MC_Demand_Set_xx_xxxxxx
AI
MC_Baseline_Minute_xx_xxxxxx
Minute
AI
MC_Period_Minute_xx_xxxxxx
Minute
6
7
Demand limit setting
The number of hours usage of an
indoor unit after the basic date
The number of hours usage of an
indoor unit within peirod
Power On/Off operation
Water Law
BV
BO
MC_Power_xx_xxxxxx
MC_Water_Law_xx_xxxxxx
Off
False
On
True
8
Quiet
BV
MC_Quiet_xx_xxxxxx
Off
On
MC_Forced_Fan_xx_xxxxxx
4
5
9
Forced Fan
BV
10
Operation mode status
MV MC_Operation_Mode_xx_xxxxxx
11
Remote controller limit status
MV MC_Remocon_Limit_xx_xxxxxx
12
Integrated error code
AI
13
DVM CHILLER Notify
NC MC_Notify_xx_xxxxxx
Status value
Text-3
Text-4 Text-5
%
Off
On
Cool
Hot
Storage Water
Enable Disable Conditional
RC
RC
RC
Cool
Heat
MC_Error_Code_xx_xxxxxx
When the error occurred, send event to list of
destination in the recipient_list. (Max : 8)
BACnet Device Object does not support master function of
DVM CHILLER.
Demand control setting range is as follows:
50,55,60,65,70,75,80,85,90,95,100(%)
SIM/PIM [Basic, Advanced]
Single SIM/PIM has following point list.
Instance
Number
Object
Object
Type
Object Name
1
SIM/PIM error code
AI
SIM_Error_Code_xx_xx
2
SIM/PIM Notify
NC
SIM_Notify_xx_xx
Status value
Refer to list of error code
When the error occurred, send event to list
of destination in the recipient_list. (Max : 8)
Centralized Controller (OnOff Controller) [Basic, Advanced]
Single Centralized Controller (OnOff Controller) has following point list.
Instance
Number
Object
Object
Type
Object Name
1
Centralized Controller
(OnOff Controller) error code
AI
Central_Error_Code_xx_xx
2
Centralized Controller
(OnOff Controller) notify
NC
Central_Notify_xx_xx
Status value
Refer to the list of the integrated
error code
When the error occurred, send event to
list of destination in the recipient_list.
(Max : 8)
E-71
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 71
2019-05-15 오후 3:57:14
BACnet Gateway setting (Continued)
Interface Module (Outdoor Unit) [Basic]
Single Interface Module (Outdoor Unit) has following point list.
Instance
Number
Object
Object
Type
Object Name
1
Outside temperature
AI
ODU_Outside_Temp_xx_xxxx
*2
Cool capacity
compensation
AV
ODU_Cool_Compensation_xx_xxxx
*3
Heat capacity
compensation
AV
4
5
6
Compressor status
Interface Module
(Outdoor Unit) error code
Interface Module
(Outdoor Unit) notify
Unit
Status value
Inactive Active
Text-1 Text-2 Text-3 Text-4 Text-5
°C
BI
0 : 5~7 °C / 1 : 7~9 °C / 2 : 9~11 °C /
3 : 10~12 °C / 4 : 11~13 °C / 5 : 12~14 °C /
6 : 13~15 °C / 14 : Auto control (from ODU)
0 : 25 kg/cm² / 1 : 26 kg/cm² /
2 : 27 kg/cm² / 3 : 28 kg/cm² /
4 : 29 kg/cm² / 5 : 30 kg/cm² /
ODU_Heat_Compensation_xx_xxxx
6 : 31 kg/cm² / 7 : 32 kg/cm² /
8 : 33 kg/cm² / 14 : Auto control (from ODU)
ODU_Comp_Status_xx_xxxx
False True
AI
Repeater_Error_Code_xx_xxxx
NC IM_Notify_xx_xxxx
Refer to the list of the integrated error code
When the error occurred, send event to list
of destination in the recipient_list. (Max : 8)
(*) Mark is optionally supported.
Interface Module (Outdoor Unit) [Advanced]
Single Interface Module (Outdoor Unit) has following point list.
Instance
Number
Object
Object
Type
Object Name
1
Outside temperature
AI
ODU_Outside_Temp_xx_xxxx
*2
Cool capacity
compensation
AV
ODU_Cool_Compensation_xx_xxxx
*3
Heat capacity
compensation
AV
4
5
Compressor status
Interface Module
(Outdoor Unit) error code
Unit
Status value
Inactive Active
Text-1 Text-2 Text-3 Text-4 Text-5
°C
BI
0 : 5~7 °C / 1 : 7~9 °C / 2 : 9~11 °C /
3 : 10~12 °C / 4 : 11~13 °C / 5 : 12~14 °C /
6 : 13~15 °C / 14 : Auto control (from ODU)
0 : 25 kg/cm² / 1 : 26 kg/cm² /
2 : 27 kg/cm² / 3 : 28 kg/cm² /
ODU_Heat_Compensation_xx_xxxx
4 : 29 kg/cm² / 5 : 30 kg/cm² /
6 : 31 kg/cm² / 7 : 32 kg/cm² /
8 : 33 kg/cm² / 14 : Auto control (from ODU)
ODU_Comp_Status_xx_xxxx
False True
AI
Repeater_Error_Code_xx_xxxx
Refer to the list of the integrated error code
Only valid for the DVM
water outdoor unit
Only valid for the DVM
False True
water outdoor unit
When the error occurred, send event to list
of destination in the recipient_list. (Max : 8)
*6
Water temperature
AI
ODU_Water_Temp_xx_xxxxx °C(°F)
*7
Hot gas charging valve
BI
ODU_HotGas_Charging_
Valve_xx_xxxxx
8
Interface Module
(Outdoor Unit) notify
NC IM_Notify_xx_xxxx
(*) Mark is optionally supported.
E-72
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 72
2019-05-15 오후 3:57:14
BACnet Gateway [Basic, Advanced]
BACnet Gateway has following point list.
Instance Control and
Number
Monitoring
1
All device OFF
Object
Type
BO
2
DMS2.5 Status
AI
3
BACnet error
code
AI
4
Gateway Notify
NC
Object Name
Status Value
ALL_OFF_xx
Inactive : All devices Off
0: Normal, 8: Emergency stop,
105 : Tracking in progress,
DMS2.5_Status_xx 108 : Tracking failed
109 : DMS2.5 ↔ BACnet Communication
failed
BACnetApp_Error_
BACnet error code
Code_xx
When the error occurred, send event to list
GW_Notify_xx
of destination in the recipient_list. (Max : 8)
DDC [Basic, Advanced]
DDC has following point list.
Instance
Number
Object
Object
Type
Object Name
1
2
3
4
5
6
7
Digital Input 1
Digital Input 2
Digital Input 3
Digital Input 4
Digital Input 5
Digital Input 6
Digital Input 7
Digital Input 8
Digital Input 9
Digital Input 10
Digital Output 1
Digital Output 2
Digital Output 3
Digital Output 4
Digital Output 5
Digital Output 6
Digital Output 7
Digital Output 8
BI
BI
BI
BI
BI
BI
BI
BI
BI
BI
BO
BO
BO
BO
BO
BO
BO
BO
DI_01_xx_xx (BACnet Gateway Reserved)
DI_02_xx_xx (BACnet Gateway Reserved)
DI_03_xx_xx
DI_04_xx_xx
DI_05_xx_xx
DI_06_xx_xx
DI_07_xx_xx
DI_08_xx_xx
DI_09_xx_xx
DI_10_xx_xx
DO_01_xx_xx (BACnet Gateway Reserved)
DO_02_xx_xx (BACnet Gateway Reserved)
DO_03_xx_xx
DO_04_xx_xx
DO_05_xx_xx
DO_06_xx_xx
DO_07_xx_xx
DO_08_xx_xx
8
9
10
11
12
13
14
15
16
17
18
Unit
Inactive
Text-1
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Off
Status value
Active
Text-2 Text-3 Text-4 Text-5
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On
On

I f communication error occurs on devices such as SIM/PIM/Centralized
Controller (OnOff Controller)/Interface Module (Outdoor Unit) etc, other
functions such as power distribution may also create a problem. You must have
BMS system to check the errors and you must take action immediately.
E-73
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 73
2019-05-15 오후 3:57:14
BACnet Gateway setting (Continued)
Other Information
Object setting when there is communication error
If any communication error occurs between the air conditioner devices, the property
will be set as below.
1. Reliability property will be set as COMMUNICATION_FAILURE.
2. Fault / Alarm flag of Status_Flags property will be set as TRUE.
3. Present_Value property is readable but the value is not guaranteed.
Object setting when there is general error
If any air conditioner related error occurs, the property will be set as below.
1. The Reliability property value of each object will be set as UNRELIABLE_OTHER.
2. FAULT / Alarm flag of Status Flags property will be set as TRUE.
Main service
Time setting
Time synchronization Service is a service that allows the time of BACnet Gateway to
be synchronized with the time of PC.
COV (Change Of Value)
COV service is supported and you can set confirmed or unconfirmed COV.
You can set lifetime value.

COV registration information will disapper when a BACnet gateway is
switched off. The reserved value caused by the power supply problem is not
guaranteed according to the BACnet regulation.

When BMS system is sending control command, don’t send it repeatedly in
a very short time.

If BMS system is sending control command repeatedly in a very short time,
DMS may be stopped due to overload.
E-74
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 74
2019-05-15 오후 3:57:14
Viewing LonWorks Gateway’s Parts
Main Parts
LonWorks Gateway Exterior
LCD Display
Shows current time and IP address. Various
messages will be displayed depending on
button input.
LCD operation button
There are 4 buttons(Menu, (Down), (Up),
Set) and you can access menu and move,
check the menu.
LED Indicator
Check 15 LED status such as Power, CPU-Alive,
Ethernet-Linked/Active, COM1~4-TX/RX,
Lon ACK, Lon SVC and Check.
LonWorks Gateway Bottom cover
Unfasten 2 screws on the bottom and
separate the bottom cover from LonWorks
Gateway. Then check cable connection part.
● LED Indicator
Item
Power
CPU Alive
Name
Status
Power indicator
Turns blue when the power is supplied.
CPU operation indicator
Blinks in orange with 1 second
intervals during normal operation.
Ethernet–Linked Internet connection indicator
Turns green during normal connection.
Internet data transmission/reception
Ethernet–Active
indicator
Channel 1~4 OnOff controller/Outdoor unit
COM1~4 – TX
Data transmission Indicator
Channel 1~4 OnOff controller/Outdoor unit
COM1~4 – RX
Data reception Indicator
Blinks in orange during normal
transmission/reception.
Blinks in green during normal
transmission.
Blinks in green during normal
reception.
Blinks in green during normal
reception.
Blinks in green during un-configured.
-N
eeds commission by integration
tool (Ex. LonMaker)
Lon ACK
LonWorks data reception indicator
Lon SVC
LonWorks device status indicator
Check
Indoor/Outdoor unit/Communication check
Turns green when notice occurs.
Indicator
E-75
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 75
2019-05-15 오후 3:57:14
Viewing LonWorks Gateway’s Parts (Continued)
LonWorks Gateway Cable Connection Part
DI Terminal1
DI Terminal2
Power Terminal
RS485 Communication Terminal
DO Terminal3 DO Terminal4
Lon Terminal
SD Card Socket
Reset Button
Name
Cable tie groove
Reserved
Ethernet Terminal
Description
DI Terminal1
Digital Input connection terminal, Channel1~Channel5
DI Terminal2
Digital Input connection terminal, Channel6~Channel10
DO Terminal3
Digital Output connection terminal, Channel1~Channel5
DO Terminal4
Digital Output connection terminal, Channel6~Channel8
Lon Terminal
Terminal Block for LonWorks communication (TP/FT-10)
Reset Button
Reset LonWorks Gateway
Power Terminal
Connect LonWorks Gateway adapter
SD card socket
Sub memory (for program update and set information saving) socket
RS485
Communication
Terminal
Connect for RS485 communication with devices such as OnOff
controller/Interface module
-COM1 ~ COM5
Ethernet Terminal
Connect LAN cable
Cable tie groove
Groove for arranging cables
E-76
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 76
2019-05-15 오후 3:57:15
LonWorks Gateway Interior
Display Board
20-pin Cable
LonWorks Board
2-pin Cable
10-pin Cable
Main Board
40-pin Cable
Sub Board
Note
If you need external circuit configuration, consult with the manufacturer.
Product Dimensions
64.80
(Unit : mm)
255
240
E-77
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 77
2019-05-15 오후 3:57:16
LonWorks Gateway setting
System Architecture
BMS system
Internet
BMS Engineering
SAMSUNG Engineering
LonWorks Gateway
OnOff
controller
PM 05:45
RS 485
Touch
Centralized
controller
Outdoor
Unit
Max 128 Indoor units
(DVM Series)

onnecting outdoor units and LonWorks Gateway
C
- You can control up to 80 outdoor units and 128 indoor units using LonWorks Gateway.
 Each communication channel of LonWorks Gateway can be connected with 16 outdoor units.
 The maximum number of indoor units (including ERV and MCU) that can be connected to
each RS485 communication channel of LonWorks Gateway is 128.
- The more outdoor units are connected, the longer time takes for tracking.

For devices that support new communication, you must set the communication mode
of the channel to 'NEW' from 'System settings  Tracking' menu. Set of Indoor/outdoor
units, with conventional communication type, cannot be connected to LonWorks
Gateway with new communication.

When setting communication channel mode as 'NEW', the address of virtual OnOff
control will be assigned.
Channel 0: Virtual OnOff controller 11, Channel 1: Virtual OnOff controller 12,
Channel 2: Virtual OnOff controller 13, Channel 3: Virtual OnOff controller 14,
Channel 4: Virtual OnOff controller 15
E-78
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 78
2019-05-15 오후 3:57:16
Compatible Devices
No
1
2
Devices
Model
Note
Indoor Unit
Outdoor Unit
DVM S HR, DVM S HP, DVM ECO,
DVM S WATER, DVM S cooling
only outdoor units and indoor
units that can be connected to
these outdoor units
Check if the LonWorks Gateway
supports each type of indoor units.
(Check the LonWorks NV list)
OnOff controller/
MCM-A202DN, MCM-A300N
Touch Centralized controller
OnOff controller :
Centralized controller
3
SIM
MIM-B12N
Needed for EHP power distribution
4
PIM
MIM-B16N
Needed for EHP power distribution
RS485 comm. type
Connected with SIM
Needed for power distribution
( Please consult Samsung for
compatible power meters)
Pulse type
Connected with PIM
Pulse Width: 20~400(ms)
Pulse: 1~10000(Wh/Pulse)
5*
Watt-hour Meter
 Products with ‘* ’ are not Samsung products and must be purchased separately.
(Only selected power meters may be used for protocol compatibility issues.)
 Samsung is not responsible for BMS engineering which creates each device and objects.
For further directions regarding on BMS engineering, consult with specialized BMS related vendor.
E-79
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 79
2019-05-15 오후 3:57:16
LonWorks Gateway setting (Continued)
Maximum Devices Attachable
Devices
Max.
Note
Indoor Unit
128
Tracking error occurs if exceeded
The maximum number of indoor units
(including ERV and MCU) that can be
connected to each communication
channel is 128.
OnOff controller /
Touch Centralized controller
75
Must not exceed 15 units per each
RS485 communication terminal
Outdoor unit
80
Must not exceed 16 units per each
RS485 communication terminal
SIM/PIM
8
-
Watt-hour Meter
64
Maximum 8 units can be connected to
1 SIM/PIM.

The sum of OnOff controller, touch centralized controller, and SIM/PIM interface
module that can be connected to each communication channel should be 15 or less.
E-80
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 80
2019-05-15 오후 3:57:16
Installing the LonWorks Gateway
Commision
● Commision using Service Pin
To activate the Service Pin, press and hold [SET] button for more than three
seconds while time is displayed in the LCD Display window of the front side of
LonWorks Gateway.
Press and hold the [SET] button
for more than 3 seconds.
When you press Service Pin, Neuron ID will be sent and [SVC] LED of the front
panel will be lit up for a second.
You should correctly set up a network according to the installation and communication
environment and set the data processing system in advance.
This Gateway provides data for 128 indoor units. However, the connectable number of
indoor units can be different according to the number of items, communication cycle or
operating environment.
Do not connect a device requiring urgent control in the same network.
E-81
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 81
2019-05-15 오후 3:57:16
LonWorks Gateway setting (Continued)
Control and Monitoring Item
● Functional classification by a device.
The functions provided can be different according to the type of the connected device.
No
NV Name
Remarks
Indoor ERV
AHU Fresh DVM FCU
Kit Duct CHILLER Kit
1
nviOnOff
ON/OFF command
O
O
O
O
O
O
2
nviApplicMode
Setting operating mode
O
X
O
O
O
O
3
nviSetpoint
Setting desirable temperature
O
X
O
X
O
O
Setting wind speed and direction
O
O
X
X
X
O
4
nviFanStatus
5
nviERVMode
Setting ERV operation mode
X
O
X
X
X
X
6
nviFilterReset
Filter reset command
O
O
O
O
X
X
7
nviUserLockout
Setting the restriction of remote
control use
O
O
O
O
O
O
8
nviOccOpMode
Setting cooling only mode / Setting
heating only mode
O
X
O
O
X
O
9
nviCoolTempLock Setting the low temperature limit
O
X
O
X
X
O
10 nviHeatTempLock Setting the high temperature limit
O
X
O
X
X
O
11 nvoSpaceTemp
O
X
O
X
O
O
Display indoor temperature
12 nvoApplicMode
Display operating mode
O
X
O
O
O
O
13 nvoSetpoint
Display desire temperature
O
X
O
X
O
O
14 nvoOnOff
Display ON/OFF status
O
O
O
O
O
O
15 nvoFanStatus
Display wind speed and direction
O
O
X
X
X
O
16 nvoERVMode
Display ERV operating mode
X
O
X
X
X
X
17 nvoErrorCode
Display Error code
O
O
O
O
O
O
18 nvoDeviceAlarm
Remote control Lock, Filter Sign,
Thermo ON/OFF, Error occurrence
status display
O
O
O
O
O
O
19 nvoOccOpMode
Cooling only/Heating only setup
status display
O
X
O
O
X
O
Low temperature limit setting
20 nvoCoolTempLock status display
O
X
O
X
X
O
High temperature limit setting
21 nvoHeatTempLock status display
O
X
O
X
X
O
O
O
O
O
O
O
22 nvoUserLockout
Display the restriction of remote
control use
23 nvoEnergyConp
Display electricity usage (Time Period)
O
X
X
X
X
X
24 nvoEnergyCon
Display electricity usage (Basic date)
O
X
X
X
X
X
25 nvoRuntimep
Display used hours (Period)
O
X
O
X
O
O
26 nvoRuntime
Display used hours (Basic date)
O
X
O
X
O
O
27 nvoDevListDesc
The summary of device information
(Model, Address, Operation Status)
O
O
O
O
O
O
 With DVM CHILLER, be cautious in setting a master device.
E-82
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 82
2019-05-15 오후 3:57:17
Although
the LonWorks Gateway can connect 128 units, the actual number of
available items can differ according to the number of indoor units connected.
When the number of indoor units is increased, the number of controllable items
will be decreased; on the other hand, as the number of indoor units decreases, the
controllable items increase.
The functions provided can be different according to the type of the connected device.
Control and Monitoring
Item
The maximum number of
connectable indoor units.
27 items (All)
22
20 items
30
15 items
40
12 items
50
9 items
64
6 items
100
4 items
128
Remarks
In the case that 20 items can
be processed per a second
and data inquiry interval is 30
seconds.
 You
can freely choose the items.
number of items that can be processed will be different according
to the time interval that inquires about data at Human Machine Interface.
LonWorks Gateway can process 20 items of Acknowledged Service Type per
a second. Therefore, the amount of data that can be processed is decided
according to how frequently HMI inquires about the data and the number of
indoor units that can be connected is decided by this amount of data.
 The
* For example : In the case that HMI inquires about the 27 items of
Acknowledged Service Type by an indoor unit.
When HMI inquires for data at 30 seconds interval, 22 indoor
units can be connected, at 60 seconds interval 44 indoor units
can be connected, at 120 seconds interval 88 indoor units can be
connected.
 The
renewal cycle can be different according to the provided NV.

When BMS system is sending control command, don’t send it repeatedly in a very
short time.

If BMS system is sending control command repeatedly in a very short time, DMS may
be stopped due to overload.
E-83
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 83
2019-05-15 오후 3:57:17
LonWorks Gateway setting (Continued)
Setting the LonWorks Gateway
LonWorks Gateway Connection and Login
1
Click internet explorer icon(
2
When internet explorer window appears, enter IP address
(http://192.168.0.100) on the address bar then press [ENTER].
3
If it is the first time to access LonWorks Gateway, “ Install Microsoft Silverlight”
message will appear.
 If the Microsoft Silverlight has already been installed, the above message will
not appear.
4
Click [Run] button and continue installation.
After installation, access LonWorks Gateway again.
) twice on your computer.
Silverlight operates normally with Windows 7 or later version. It may not
operate normally with previous version of Windows.
5
Enter ID and password when LonWorks Gateway main web page appears, Then
click [LOGIN].
 If you use accounts with general authorization level to login, you cannot use
the LonWorks Gateway settings.
 Depending on authorization level set by the administrator, access to some
functions may be restricted.
 You can change authorization level settings from System settings 
User authorization management.
 To use the LonWorks Gateway functions, you must login with the ID that is
included in administration group. Factory default LonWorks Gateway ID is
‘admin’ and password is ‘ac0530’.
Note
 Only authorized users can access web page.
C
onnection speed may slow down. Fewer than 5 concurrent users are
recommended.
 L onWorks Gateway manager should change ID and password for security
and management.
 Logout: If you want to logout, click [LOGOUT] on the top of the menu.
LonWorks Gateway will be ended.

If you use accounts with authorization level lower than management group or accounts
with general authorization level, you cannot access LonWorks Gateway settings.

If you cannot access LonWorks Gateway, consult the manager.
E-84
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 84
2019-05-15 오후 3:57:17
6
If you login successfully, 'Control and Monitoring' screen of DMS2.5 will appear.
Click [System Setting]➔[LonWorks configuration] menu to switch to LonWorks
Gateway.

If you use accounts with authorization level lower than management group or
accounts with general authorization level, LonWorks configuration will not be
displayed on the menu.

If the LonWorks configuration menu does not appear, consult the manager.
7
If you access LonWorks Gateway, 'Device Configuration' screen will appear initially.
 If you click [DMS2.5 Connect] button, screen will be switched to initial screen of
the DMS2.5.
Reading EHP Watt-hour Meter
Setting and checking watt-hour meter
1
Click [Setting and Checking Watt-hour meter].
 You can change settings on watt-hour meter only when SIM/PIM interface
module is connected.
2
Click [Edit] from the 'Setting and checking Watt-hour meter' screen.
 CT proportion is set to ‘1’ as factory default value.
3
Set the [Name] and [CT proportion] for the watt-hour meter.
 You can use maximum 16 letters for name and only available special characters
are “.”, ”,”, ”_”, ”-“, and “space”.
 Value for CT proportion should be integer between range of 1 ~ 5000.
4
Click [Save].
 Changed settings will be saved to the LonWorks Gateway.
 If you do not click [Save] changed setting will not be saved.
5
Watt-hour meter value will display the actual value of electricity on the
corresponding watt-hour meter. Value will be updated automatically.
When using CT watt-hour meter, be careful that there can be difference with
actual power consumption as much as CT ratio error.
E-85
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 85
2019-05-15 오후 3:57:17
LonWorks Gateway setting (Continued)
Monthly baseline setting
1
Click [Setting and Checking Watt-hour meter].
2
Click [Edit] from the ‘Monthly baseline setting’ screen.
 You can make changes when list box enables.
3
Set the Monthly baseline setting.
 You can select from 1~31.
 If you select the last day of the month, it will automatically set the last day
of corresponding month as baseline.
Ex) Last day of February: 28th or 29th
 Power consumption is calculated for a month before monthly baseline.
Ex) Monthly baseline: 28th
Today: 19th Nov.
Time period for power consumption and operation: 29th Sep. ~ 28th Oct.
4
Click [Save].
 Changed settings will be saved to the LonWorks Gateway.
 If you do not click [Save] changed setting will not be saved.
Period setting
1
Click [Setting and Checking Watt-hour meter].
2
Click [Edit] from the ‘Period setting’ screen.
 You can select checkbox to set period in daily or monthly unit.
 If you select daily period setting, text box will be enabled and you can enter
the period in daily unit.
 If you select monthly period setting, you can select the period in monthly
unit.
3
Set the period
 If you set period in daily unit, you can set up to maximum 90 days.
 If you set period in monthly unit, you can set up to maximum 1 month.
4
Click [Save].
 Changed setting will be saved to LonWorks Gateway.
 If you do not click [Save], changed setting will not be saved.
E-86
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 86
2019-05-15 오후 3:57:17
Device Configuration
Checking and changing the Object ID
List of equipment connected to LonWorks can be checked when
the tracking is completed.
1
Device Type, Address, Name and Object ID will appear.
2
Object IDs are assigned in order from 1 to 128 when initial
tracking is executed.
3
If you want to change the Object ID, click [Edit] and
change the Object ID of the applicable device.
 The Object ID can not be used for more than one piece
of device.
 Object ID can be entered between 1 ~ 128.
 Device without an Object ID can not transfer its
information to LonWorks.
O
bject ID does not appear if there are more than 128
indoor units.
Checking device information
1
Click one of the Addresses from ‘Address’ colum.
D
etail information of the selected device will be displayed
in device information.
2
You can check the value of each Input item.
Note
3
 The value of the Input item represents the current
status of the device.
Therefore, value may be different from the final status
controlled by LonWorks MMI.
 Some values cannot be altered depending on their
connection to a type of device
(Indoor unit, ERV, AHU kit, Fresh ducts).
Check the current value of the Output.
The current value indicates the current status of
indoor unit(ERV) and the value can be different due to
synchronization delay with LonWorks MMI and data
conversion.
 Refer to LonWorks Message Definition for device
information display for each device.
E-87
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 87
2019-05-15 오후 3:57:17
LonWorks Gateway setting (Continued)
Overview for Function
 Followings are the NV lists of indoor unit(ERV/AHU kit/Fresh ducts) supported by LonWorks
Gateway.
1) nvi type - Data setting is allowed
2) nvo type - Data setting is not allowed
Please refer to Message Definition for Setting value.
1. Indoor Unit(ERV/AHU Kit/Fresh ducts/DVM Chiller/FCU Kit) Objects
No.
NV Name
NV Type
Remarks
1
nviOnOff
SNVT_switch
ON/OFF command
2
nviApplicMode
SNVT_hvac_mode
Setting operating mode
3
nviSetpoint
SNVT_temp_p
Setting desirable temperature
4
nviFanStatus
SNVT_switch
Setting wind speed and direction
5
nviERVMode
SNVT_count
Setting ERV operation mode
6
nviFilterReset
SNVT_switch
Filter reset command
7
nviUserLockout
SNVT_switch
Setting the restriction of remote control use
8
nviOccOpMode
SNVT_switch
Setting cooling only mode / Setting heating
only mode
9
nviCoolTempLock
SNVT_switch
Setting the low temperature limit
10
nviHeatTempLock
SNVT_switch
Setting the high temperature limit
11
nvoSpaceTemp
SNVT_temp_p
Display indoor temperature
12
nvoApplicMode
SNVT_hvac_mode
Display operating mode
13
nvoSetpoint
SNVT_temp_p
Display desire temperature
14
nvoOnOff
SNVT_switch
Display ON/OFF status
15
nvoFanStatus
SNVT_switch
Display wind speed and direction
16
nvoERVMode
SNVT_count
Display ERV operating mode
17
nvoErrorCode
SNVT_count
Display Error code
18
nvoDeviceAlarm
SNVT_state
Remote control Lock, Filter Sign, Thermo
ON/OFF, Error occurrence status display
19
nvoOccOpMode
SNVT_switch
Cooling only/Heating only setup status
display
20
nvoCoolTempLock
SNVT_switch
Low temperature limit setting status display
21
nvoHeatTempLock
SNVT_switch
High temperature limit setting status display
22
nvoUserLockout
SNVT_switch
Display the restriction of remote control use
23
nvoEnergyConp
SNVT_elec_kwh_l
Display electricity usage (Time Period)
24
nvoEnergyCon
SNVT_elec_kwh_l
Display electricity usage (Basic date)
25
nvoRuntimep
SNVT_time_hour
Display used hours (Period)
26
nvoRuntime
SNVT_time_hour
Display used hours (Basic date)
27
nvoDevListDesc
SNVT_str_asc
The summary of device information
(Model, Address, Operation Status)
E-88
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 88
2019-05-15 오후 3:57:17
2. DMS system Objects
No.
NV Name
NV Type
Remarks
1
nviDigitalOut[6]
SNVT_ switch
Control Digital output of DMS
2
nviAllOff
SNVT_hvac_emerg
Control all indoor unit / ERV OFF
3
nvoDigitalOut[6]
SNVT_ switch
Display Digital output status of DMS
4
nvoDigitalIn[8]
SNVT_ switch
Display Digital input status of DMS
5
nvoSystemLock
SNVT_switch
Display System Lock status of DMS
6
nvoDMSAlarm
SNVT_ count
Display communication error of the sub
device connected to DMS
7
nvoSystemAlarm
SNVT_ count
3. Configuration Properties
No.
NV Name
NV Type
Remarks
1
nciSndHrtBt
SNVT_time_sec
SCPTmaxSendTime
Send Heartbeat
2
nciMinOutTm
SNVT_time_sec
SCPTminSendTime
Minimum Send Time
3
nciMinDeltaTemp
SNVT_temp_p
SCPTminDeltaTemp
Min. difference before update
4
nciDelayStatrup
SNVT_time_sec
SCPTpwrupDelay
Delay time after a power-up
<Unused Network Variables>
The network variable listed below do exist within our XIF file. However, they are not
explained in this document. They are exclusively intended for internal testing purpose
and should not be used by a user.
◆ nvlVolt
◆ nvoVoltFb
E-89
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 89
2019-05-15 오후 3:57:17
LonWorks Gateway setting (Continued)
Network Parameter Chart
Indoor/ERV/AHU kit/Fresh ducts/DVM Chiller/FCU Kit objects
SSACIndoor[nn](object id = 1-128)
nvoSpaceTemp
SNVT_temp_p
nviOnOff
SNVT_switch
nviApplicMode
SNVT_hvac_mode
nviSetPoint
SNVT_temp_p
nviFanStatus
SNVT_switch
nviERVMode
SNVT_count
nviFilterReset
SNVT_switch
nvoApplicMode
SNVT_hvac_mode
nvoSetPoint
SNVT_temp_p
nvoOnOff
SNVT_switch
nvoFanStatus
SNVT_switch
nvoERVMode
SNVT_count
nvoErrorCode
SNVT_count
nvoDeviceAlarm
SNVT_state
nviUserLockout
SNVT_switch
nvoOccOpMode
SNVT_switch
nviOccOpMode
SNVT_switch
nvoCoolTempLock
SNVT_switch
nviCoolTempLock
SNVT_switch
nviHeatlTempLock
SNVT_switch
nvoHeatTempLock
SNVT_switch
nvoUserLockout
SNVT_switch
nvoEnergyConp
SNVT_elec_kwh_l
nvoEnergyCon
SNVT_elec_kwh_l
nvoRuntimep
SNVT_time_hour
nvoRuntime
SNVT_time_hour
nvoDevListDesc
SNVT_str_asc
E-90
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 90
2019-05-15 오후 3:57:17
DMS system objects
SSACSystem(object id = 129)
nvoDigitalOut[6]
SNVT_switch
nviDigitalOut[6]
SNVT_switch
nvoDigitalIn[8]
SNVT_switch
nviAllOff
SNVT_hvac_emerg
nvoSystemLock
SNVT_switch
nvoDMSAlarm
SNVT_count
nvoSystemAlarm
SNVT_count
Configuration Properties
nciSndHrtBt
nciMinOutTm
nciMinDeltaTemp
nciDelayStatrup
E-91
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 91
2019-05-15 오후 3:57:17
LonWorks Gateway setting (Continued)
Message Definition
Data for Indoor Device
● nvoSpaceTemp(11)
Description
SNVT Type
Value and operation
Indoor temperature
SNVT_temp_p: Signed Long, 2 bytes
Range: -10.00 °C ~ 50.00 °C
● nvoApplicMode(12), nviApplicMode(2)
Description
SNVT Type
Value and operation
Operation Mode status
SNVT_hvac_mode: Enumeration(hvac_t)
0: HVAC_AUTO
1: HVAC_HEAT
3: HVAC_COOL
6: HVAC_OFF
9: HVAC_FAN_ONLY
11: HVAC_ICE(Cool Storage)
13: HVAC_ECONOMY(Hot Water)
14: HVAC_DEHUMID
❈ Invalid Value: Automatically set as HVAC_AUTO
● nvoSetpoint(13), nviSetpoint(3)
Description
SNVT Type
Value and operation
Set Temperature
SNVT_temp_p: Signed Long, 2 bytes
Cool: 18.0 °C ~ 30.0 °C, Heat: 16.0 °C ~ 30.0 °C
❈ Invalid Value: Automatically set up as minimum or
maximum value.
❈ When setting temperature, only an integer value is
applied. A decimal point is ignored.
❈ DVM CHILLER: -10 °C ~ 55 °C
● nvoOnOff(14), nviOnOff(1)
Description
SNVT Type
Value and operation
Power ON/OFF status
SNVT_switch: Unsigned/signed Short
OFF
ON
Value
0.0
100.0
State
0
1
E-92
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 92
2019-05-15 오후 3:57:17
● nvoFanStatus(15), nviFanStatus(4)
Description
SNVT Type
Value and operation
Fan Speed and direction
SNVT_switch: Unsigned/signed Short
Auto
Low
Mid
High
Eco
Turbo
Auto
Value
0.0
1.0
2.0
3.0
4.0
5.0
Any>5.0
State
-
Stop
Up-Down
-
0
1
❈ Supporting modes are different according to indoor units.
- Indoor unit/FCU Kit: Auto, Low, Mid, High (Turbo : Optional)
- ERV : Mid, High, Turbo
- AHU Kit: High
* When an indoor unit operation mode is Auto or Dehumid,
Fan speed is controlled as ‘Auto’.
* When an indoor unit operation mode is FAN ONLY, ‘Auto’
cannot be controlled by Fan speed.
● nvoERVMode(16), nviERVMode(5)
Description
SNVT Type
Value and operation
ERV Operation Mode
SNVT_count: Unsigned Long, 2 bytes
( 0: Auto )
1: H/R
( 2: Air purification )
3: Sleep
4: Normal
❈ ( ) : Function that is not supported now.
● nvoErrorCode(17)
Description
SNVT Type
Value and operation
Error Code
SNVT_count: Unsigned Long, 2 bytes
Valid Range: 0 ~ 999
00 00 → No Error
Refer to list of Error code
E-93
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 93
2019-05-15 오후 3:57:18
LonWorks Gateway setting (Continued)
● nvoDeviceAlarm(18)
Description
SNVT Type
1. Remote control restriction status
2. Filter alert status
3. Thermo On/Off status
4. Error alert Status
SNVT_state: 16 Unsigned Bitfields
Byte
Flags_1
Byte
Value and operation
Bit9
0
0
1
Bit8
0
1
0
Operation
Unlock
Level1
Lock
Bit
value
0
1
0
1
0
1
Operation
No alarm
Alarm
Thermo Off
Thermo On
No Error
Error
2
Flags_2
1
0
Remark
nvoUserLockout
Remark
nvoFilterAlarm
Thermo On/Off
nvoErrorCode
● nvoOccOpMode(19), nviOccOpModeCmd(8)
Description
SNVT Type
Value and operation
Operation Mode restriction
SNVT_switch: Unsigned/singed Short
Unlock
Cool only
Heat only
Value
0.0
1.0
2.0
State
0
1
1
● nvoCoolTempLock(20), nviCoolTempLock(9)
Description
SNVT Type
Value and operation
Setting/monitoring Lower limit temperature
and function toggle
SNVT_switch: Unsigned/singed Short
Operation
Unlock
Lock
Value
18.0 ~ 30.0
18.0 ~ 30.0
State
0
1
Cool: 18.0 °C ~ 30.0 °C
E-94
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 94
2019-05-15 오후 3:57:18
● nvoHeatTempLock(21), nviHeatTempLock(10)
Description
SNVT Type
Value and operation
Setting/monitoring upper limit temperature
and function toggle
SNVT_switch: Unsigned/signed Short
Operation
Unlock
Lock
Value
16.0 ~ 30.0
16.0 ~ 30.0
State
0
1
Heat: 16.0 °C ~ 30.0 °C
● nvoEnergyConp(23)
Description
SNVT Type
Value and operation
Electric consumption value within the period
SNVT_elec_kwh_I: Signed Quad, 4bytes
Raw range: 0 ~ 999999
Resolution: 0.1
● nvoEnergyCon(24)
Description
SNVT Type
Value and operation
Electric consumption value after baselin
SNVT_elec_kwh_I: Signed Quad, 4bytes
Raw range: 0 ~ 999999
Resolution: 0.1
● nvoRunTimep(25)
Description
SNVT Type
Value and operation
Indoor unit usage within the period
SNVT_time_hour: Signed Long, 2bytes
Raw range: 0 ~ 65535
● nvoRunTime(26)
Description
SNVT Type
Value and operation
Indoor unit usage after baseline
SNVT_time_hour: Signed Long, 2bytes
Raw range: 0 ~ 65535
❈ Energy consumption and Runtime are the accumulated value
during the user setting period.
❈ The data above is for reference so you can not use them for
official billing.
E-95
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 95
2019-05-15 오후 3:57:18
LonWorks Gateway setting (Continued)
● nviFilterReset(6)
Description
SNVT Type
Filter alert reset
SNVT_switch: Unsigned/singed Short
Value
0.0
100.0
Value and operation
State
0
1
Operation
No Action
Filter Reset
remark
● nviUserLockout(7), nvoUserLockout(22)
Description
SNVT Type
Remote control restriction
SNVT_switch: Unsigned/singed Short
Value
0.0
100.0
100.0
Value and operation
State
0
1
2
Operation
Unlock
Level 1
Lock
remark
● nvoDevListDesc(27)
Description
SNVT Type
Value and operation
Device Information
SNVT_str_asc: Unsigned Character Array, 31bytes
Refer to Expansion of nvoDevListDesc
E-96
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 96
2019-05-15 오후 3:57:18
● Expansion of nvoDevListDesc
desription
[0]
Model information
Alphabet or digit
Alphabet or digit
Alphabet or digit
Alphabet or digit
Alphabet or digit
Alphabet or digit
Separator
Underbar(_)
OnOff controller address
Alphabet or digit
Alphabet or digit
[9]
Separator
Period(.)
[10]
[11]
Alphabet or digit
Interface Module address
Alphabet or digit
[12]
Separator
Period(.)
Indoor Unit Address
Alphabet or digit
Alphabet or digit
[15]
Separator
Underbar(_)
[16]
Unit type
0: indoor unit, 1: AHU, 2: ERV
[17]
Separator
Underbar(_)
[18]
Operation mode
DMS Format
0: Auto, 1: Cool, 2: Dehumid,
3: Fan, 4: Heat, 5: Cool Storage,
6: Hot Water
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[13]
[14]
ascii.
character
[19]
ON/OFF
0, 1
[20]
Fan speed
0, 1, 2, 3, 4, 5
[21]
Fan Swing
0, 1
[22]
Error
0, 1
[23]
Separator
Underbar(_)
setPoint Temperature
Second significant digit
First significant digit
First decimal place
[28] Space Temperature(*)
Second significant digit
First significant digit
First decimal place
[24]
[25]
[26]
[27]
[29]
[30]
Null padding
0
value
095
046
046
095
095
095
048
(*) If the value is a negative number, it is displayed as sign, 10-digit, single-digit.
E-97
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 97
2019-05-15 오후 3:57:18
LonWorks Gateway setting (Continued)
Data for DMS System
● nvoDigitalOut(3), nviDigitalOut(1)
Description
SNVT Type
Digital output status on DMS
SNVT_switch: Unsigned/singed Short
OFF
ON
Value and operation
Value
0.0
100.0
State
0
1
● nvoDigitalIn(4)
Description
SNVT Type
Digital Input status on DMS
SNVT_switch: Unsigned/singed Short
OFF
ON
Value and operation
Value
0.0
100.0
State
0
1
● nvoSystemLock(5)
Description
SNVT Type
System lock status of DMS(only monitoring available)
SNVT_switch: Unsigned/singed Short
Unlock
Lock
Value and operation
Value
0.0
100.0
State
0
1
● nvoDMSAlarm(6)
Description
SNVT Type
Value and operation
DMS Alarm
SNVT_count : Unsigned Long, 2 bytes
0 : Normal
8 : Emergency stop
105 : Tracing in progress
108 : Tracking failed
109 : Lon Module ↔ DMS2.5 communication Error
110 : Object ID Update
E-98
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 98
2019-05-15 오후 3:57:18
● nvoSystemAlarm(7)
Description
SNVT Type
Value and operation
SIM/PIM Communication Error Code
SNVT_count: Unsigned Long, 2 bytes
SIM/PIM Communication Error Refer to list of Error code
● nviAllOff(2)
Description
All indoor units turn off
SNVT Type
Enumeration, emerg_t
Value and operation
0 : EMERG_NORMAL
4 : EMERG_SHUTDOWN
E-99
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 99
2019-05-15 오후 3:57:18
LonWorks Gateway setting (Continued)
Configuration Properties
● Overview
This document provides information on all configuration properties defined for
LonWorks Gateway device. For the sake of simplicity, although the configuration
properties are defined to UFPTSSACSystem functional block, they are shared
among the members of UFPTSSACIndoor functional blocks.
● Configuration Properties Table
No
CPNV Name
SCPT Reference
SNVT Type
Resolution
1
nciSndHrtBt
2
nciMinOutTm
SCPTmaxSendTime
SNVT_time_sec
0.1
SCPTminSendTime
SNVT_time_sec
3
0.1
nciMinDeltaTemp
SCPTminDeltaTemp
SNVT_temp_p
0.01
4
nciDelayStartup
SCPTpwrUpDelay
SNVT_time_sec
0.1
Details of Configuration Properties
● Send Heartbeat
This configuration property defines the maximum period of time that expires
before the specified network variable outputs will automatically be updated.
The associated network variable will also be transmitted as a heartbeat output
on a regular basis as dictated by the Maximum Send Time (nciSndHrtBt)
configuration value.
Valid Range
The valid range is any value between 0.0 sec and 6,553.4 sec. Setting nciSndHrtBt
= 0.0 (default value) disables the Send Heartbeat mechanism.
Recommendations
If required, especially in an event-driven update for monitoring, set a value
greater than the default update rate (currently, 10s).
Associate Values
nvoDMSAlarm, nvoSystemAlarm.
● Minimum Send Time
This configuration property defines the minimum period of time between
automatic network variable output transmissions. The associated network
variable will be updated no faster than the Minimum Send Time (nciMinOutTm)
configuration value.
Valid Range
The valid range is any value between 0.0 sec and 6,553.4 sec. Setting
nciMinOutTm = 0.0 (default value) disables the Minimum Send Time mechanism.
E-100
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 100
2019-05-15 오후 3:57:18
Recommendations
If required, set a value greater than the default update rate (currently, 10s). Any smaller
value does not yield a change in the update pattern.
Associate Values
nvoSpaceTemp, nvoSetPoint
● Minimum Temperature Change
This configuration property sets the minimum temperature change required before
the associated output network variable is updated. The associate network variable
will not be updated unless the change is greater than or equal to the Minimum
Temperature Change (nciMinDeltaTemp) configuration value.
Valid Range
The valid range is any value between -273.17ºC and 327.66ºC. Setting
nciMinDeltaTemp = 0.0 (default value) disables the Minimum Temperature Change
mechanism.
Recommendations
If required, set a value greater than 0.1 degree in Celsius. Also, consider the maximum
of the typical operating range which is 50 degree in Celsius.
Associate Values
nvoSpaceTemp, nvoSetPoint
● Start-Up Delay
This configuration property controls the minimum period of time that expires before
outputs are retransmitted. It also is the minimum amount of elapsed time after a
power-up or re-establishment of communications before a control action takes
place. This can be used to account for the settle-down time of a network.
All of the output network variable will be updated no faster than the Start-Up Delay
(nciDelayStartup) configuration value. Also, the heartbeat mechanism will not be
enabled unless the elapsed time passes the Start-Up Delay, if used.
Valid Range
The valid range is any value between 0.0 sec and 6,553.4 sec. Setting nciDelayStartup
= 0.0 disables the Start-Up Delay mechanism.
Associate Values
All output network variables
Recommendations
If required, set a value greater than 1 minute which is a settle-down time of the
installed device.
E-101
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 101
2019-05-15 오후 3:57:18
Specifications
Items
Description
Exterior
Size
Weight
Source
Power
INPUT Voltage
OUTPUT Voltage
RS-485
Ethernet
SD CARD
Interface
DI
DO
Etc.
Display
Input method
240 X 255 X 64.8 mm ( Width X Length X Height )
1.48 Kg
DC ADAPTOR
100-240V 50/60Hz 1.0A
12V 3A
5 Channels
10/100Mbps 1 Port
Option (Purchase SD card separately)
12V Digital Input 10 Channels
12V Digital Output 8 Channels
Serial Port, Reset Button
16-Character X 2-Line Character LCD
Menu/Up/Down/Set 4-Tact Button
E-102
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 102
2019-05-15 오후 3:57:18
License
Open Source Announcement
The software included in this product contains open source software. You may obtain the
complete corresponding source code for a period of three years after the last shipment of this
product by sending an email to mailto:oss.request@samsung.com.
It is also possible to obtain the complete corresponding source code in a physical medium
such as a CD-ROM; a minimal charge will be required.
The following URL http://opensource.samsung.com/opensource/DMS2_5/seq/1 leads to the
download page of the source code made available and open source license information as
related to this product. This offer is valid to anyone in receipt of this information.
E-103
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 103
2019-05-15 오후 3:57:18
DB68-06095A-03
SOL_NASA_DMS2.5&BAC&LW_IBIM_EN_06095A-03.indd 104
2019-05-15 오후 3:57:18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising