Samsung Samsung Harman Kardon Soundbar Q80R 用戶手冊

FULL MANUAL
HW-Q80R
Imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at www.samsung.com/register
SAFETY INFORMATION
SAFETY WARNINGS
WARNING
•• To reduce the risk of fire or electric shock, do
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
not expose this appliance to rain or moisture.
NOT REMOVE THE COVER (OR BACK).
CAUTION
NO USER-SERVICEABLE PARTS ARE INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
•• TO PREVENT ELECTRIC SHOCK, MATCH WIDE
PERSONNEL.
BLADE OF PLUG TO WIDE SLOT, FULLY
Refer to the table below for an explanation of
INSERT.
symbols which may be on your Samsung product.
•• This apparatus shall always be connected to a
AC outlet with a protective grounding
connection.
CAUTION
•• To disconnect the apparatus from the mains,
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
the plug must be pulled out from the mains
socket, therefore the mains plug shall be
This symbol indicates that high voltage
is present inside. It is dangerous to
make any kind of contact with any
internal part of this product.
readily operable.
•• Do not expose this apparatus to dripping or
splashing. Do not put objects filled with
This symbol indicates that this product
has included important literature
concerning operation and maintenance.
liquids, such as vases on the apparatus.
•• To turn this apparatus off completely, you
Class II product : This symbol indicates
must pull the power plug out of the wall
socket. Consequently, the power plug must
be easily and readily accessible at all times.
that it does not require a safety
connection to electrical earth (ground).
If this symbol is not present on a
product with a power cord, the product
MUST have a reliable connection to
protective earth (ground).
AC voltage : This symbol indicates that
the rated voltage marked with the
symbol is AC voltage.
DC voltage : This symbol indicates that
the rated voltage marked with the
symbol is DC voltage.
Caution, Consult instructions for use :
This symbol instructs the user to
consult the user manual for further
safety related information.
ENG - ii
PRECAUTIONS
5. The battery used with this product contains
chemicals that are harmful to the
environment. Do not dispose of the battery
1. Ensure that the AC power supply in your
in the general household trash. Do not
house complies with the power
expose the battery to excess heat, direct
requirements listed on the identification
sunlight, or fire. Do not short circuit,
sticker located on the bottom of your
disassemble, or overheat the battery.
product. Install your product horizontally, on
Danger of explosion if the battery is replaced
a suitable base (furniture), with enough
incorrectly. Replace only with the same or
space around it for ventilation (7~10 cm).
equivalent type.
Make sure the ventilation slots are not
covered. Do not place the unit on amplifiers
or other equipment which may become hot.
This unit is designed for continuous use. To
fully turn off the unit, disconnect the AC plug
from the wall outlet. Unplug the unit if you
intend to leave it unused for a long period of
ABOUT THIS MANUAL
The user manual has two parts: this simple paper
USER MANUAL and a detailed FULL MANUAL you
can download.
time.
2. During thunderstorms, disconnect the AC
plug from the wall outlet. Voltage peaks due
to lightning could damage the unit.
3. Do not expose the unit to direct sunlight or
USER MANUAL
other heat sources. This could lead to
See this manual for safety instructions,
overheating and cause the unit to
product installation, components,
malfunction.
connections, and product specifications.
4. Protect the product from moisture (i.e.
vases), and excess heat (e.g. a fireplace) or
equipment creating strong magnetic or
electric fields. Unplug the power cable from
the AC wall socket if the unit malfunctions.
Your product is not intended for industrial
use. It is for personal use only. Condensation
may occur if your product has been stored in
cold temperatures. If transporting the unit
during the winter, wait approximately
2 hours until the unit has reached room
temperature before using.
FULL MANUAL
You can access the FULL MANUAL on
Samsung’s on-line customer support centre by
scanning the QR code. To see the manual on
your PC or mobile device, download the
manual in document format from Samsung’s
website. (http://www.samsung.com/support)
Design, specifications, and App screen are subject to
change without prior notice.
ENG - iii
CONTENTS
01
Checking the Components
Inserting Batteries before using the Remote Control (AA batteries X 2)
02
03
04
05
06
2
--------------------------
Product Overview
2
3
Front Panel / Top Panel of the Soundbar
--------------------------
3
Bottom Panel of the Soundbar
--------------------------
4
Connecting the Soundbar
5
Connecting Electrical Power
--------------------------
5
Connecting the Soundbar to the Subwoofer
–– Automatic connection between the Subwoofer and the Soundbar
–– Manually connecting the Subwoofer if automatic connection fails
----------------------------------------------------------------------------
6
6
7
Connecting an SWA-9000S (Sold Separately) to your Soundbar
--------------------------
8
Connecting to your TV
10
Method 1. Connecting with a Cable
–– Connecting a TV using an HDMI Cable
–– Connecting using an Optical Cable
-------------------------- 10
-------------------------- 10
-------------------------- 11
Method 2. Connecting Wirelessly
–– Connecting a TV via Bluetooth
–– Connecting via Wi-Fi
-------------------------- 12
-------------------------- 12
-------------------------- 14
Connecting an External Device
16
Connecting using an HDMI Cable (Capable of Dolby Atmos decoding
and playback)
-------------------------- 16
Connecting using an HDMI Cable
-------------------------- 17
Connecting using an Optical Cable
-------------------------- 18
Connecting a Mobile Device
19
Connecting via Bluetooth
-------------------------- 19
Connecting via Wi-Fi (Wireless Network)
-------------------------- 22
ENG - iv
07
08
09
10
Connecting an Amazon product
24
Connect and use with an Amazon product (Amazon Echo)
-------------------------- 24
Use voice commands to control the Soundbar
-------------------------- 26
Using the Remote Control
27
How to Use the Remote Control
-------------------------- 27
Adjusting the Soundbar volume with a TV remote control
-------------------------- 30
Using the Hidden Buttons (Buttons with more than one function)
-------------------------- 31
Output specifications for the different sound effect modes
-------------------------- 31
Installing the Wall Mount
32
Installation Precautions
-------------------------- 32
Wallmount Components
-------------------------- 32
Installing the Soundbar above a TV Stand
Component
34
-------------------------- 34
11
Software Update
35
12
Troubleshooting
36
13
Licence
37
14
Open Source Licence Notice
38
15
Important Notes About Service
38
16
Specifications and Guide
39
Specifications
-------------------------- 39
ENG - v
01 CHECKING THE COMPONENTS
PAIR
SOUND
MODE
VOL
WOOFER
SOUNDBAR
Soundbar Main Unit
1
Remote Control / Batteries
Subwoofer
2
x2
Power Cord
(Subwoofer)
Power Cord
(Main Unit)
HDMI Cable
x2
x2
Bracket-Wall Mount
x4
(M4 x L10)
Wall Mount Guide
Holder-Screw
Screw
Rubber-Foot
•• For more information about the power supply and power consumption, refer to the label attached
to the product. (Label: Bottom of the Soundbar Main Unit)
•• The power components are labelled (1, 2). For more information about power connections, see
page 5.
•• To purchase additional components or optional cables, contact a Samsung Service Centre or
Samsung Customer Care.
•• The appearance of the accessories may differ slightly from the illustrations above.
Inserting Batteries before using the Remote Control (AA batteries X 2)
Slide the battery cover in the direction of the arrow
until it is completely removed. Insert 2 AA batteries
(1.5V) oriented so that their polarity is correct. Slide
the battery cover back into position.
ENG - 2
02 PRODUCT OVERVIEW
Front Panel / Top Panel of the Soundbar
Position the product so that the
Top
Panel
"Samsung Harman Kardon" logo
is located on the top.
(Power) Button
Turns the power on and off.
•• Auto Power Down Function
The unit turns off automatically in the following situations:
–– In D.IN / HDMI 1 / HDMI 2 / WIFI / BT mode if there is no audio signal for 18 minutes.
(Source) Button
Selects the source input mode.
Input mode
Display
Optical Digital input
D.IN
ARC (HDMI OUT) input
D.IN  TV ARC (Auto conversion)
HDMI input
HDMI 1 / HDMI 2
Wi-Fi mode
WIFI
BLUETOOTH mode
BT
-/+ (Volume) Button
Adjusts the volume.
•• When adjusted, the volume level appears on the Soundbar’s front display.
Display
Displays the product’s status and current mode.
•• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.
•• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.
•• If you want to enjoy sound only from the Soundbar, you must turn off the TV’s speakers in the Audio
Setup menu of your TV. Refer to the owner’s manual supplied with your TV.
ENG - 3
Bottom Panel of the Soundbar
POWER
POWER
POWER
DIGITAL AUDIO IN DIGITAL AUDIO IN
(OPTICAL)
(OPTICAL)
SERVICE
SERVICE
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
ID SET
(WOOFER/REAR)
ID SET
(WOOFER/REAR)
ID SET
(WOOFER/REAR)
NETWORK
NETWORK
NETWORK
HDMI IN 1
HDMI IN 1
HDMI IN 1
HDMI IN 2
HDMI IN 2
HDMI IN 2
HDMI OUT
(TV-ARC)
HDMI OUT
(TV-ARC)
HDMI OUT
(TV-ARC)
POWER
POWER
POWER
ID SET
ID SET
ID SET
(WOOFER/REAR)
(WOOFER/REAR)
(WOOFER/REAR)
SERVICE
SERVICE
SERVICE
HDMI
HDMI
INHDMI
IN
1 1 IN 1
HDMI
HDMI
INHDMI
IN
2 2 IN 2
NETWORK
NETWORK
NETWORK
DIGITAL
DIGITAL
DIGITAL
AUDIO
AUDIO
AUDIO
IN IN IN
(OPTICAL)
(OPTICAL)
(OPTICAL)
HDMI
HDMI
OUT
HDMI
OUT OUT
(TV-ARC)
(TV-ARC)
(TV-ARC)
DIGITAL AUDIO IN
(OPTICAL)
POWER
SERVICE
ID SET
(WOOFER/REAR)
HDMI IN 1
NETWORK
HDMI IN 2
HDMI OUT
(TV-ARC)
POWER
Connect the Soundbar's AC power cord.
POWER
SERVICE
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN 1
ID SET
ID SET (WOOFER/REAR)
(WOOFER/REAR)
Press to connect the Soundbar to surround NETWORK
speakers and a subwoofer wirelessly.
HDMI IN 2
•• Press and hold the Up button on the remote for 5 seconds to complete ID SET.
NETWORK
Press to connect to a wireless network (Wi-Fi) via the SmartThings app.
SERVICE
Connect a USB storage device to upgrade the product's software.
DIGITAL AUDIO IN (OPTICAL)
Connect to the digital (optical) output of an external device.
HDMI IN 1 / HDMI IN 2
Inputs digital video and audio signals simultaneously using an HDMI cable.
Connect to the HDMI output of an external device.
HDMI OUT
(TV-ARC)
HDMI OUT (TV-ARC)
Connect to the HDMI (ARC) jack on a TV.
•• When disconnecting the power cord from a wall outlet, pull the plug. Do not pull the cable.
•• Do not connect this unit or other components to an AC outlet until all connections between
components are complete.
ENG - 4
03 CONNECTING THE SOUNDBAR
Connecting Electrical Power
Use the power components (1, 2) to connect the Subwoofer and Soundbar to an electrical outlet in the
following order:
1 Connect the power cord to the Subwoofer.
2 Connect the power cord to the Soundbar.
See the illustrations below.
•• For more information about the required electrical power and power consumption, refer to the
label attached to the product. (Label: Bottom of the Soundbar Main Unit)
1 Power Cord
POWER
Rear of Subwoofer
POWER
Connecting
Electrical Power
POWER
2 Power Cord
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
POWER
ID SET
(WOOFER/REAR)
HDMI IN 1
NETWORK
HDMI IN 2
HDMI OUT
(TV-ARC)
Bottom of the Soundbar
Main Unit
Connecting Electrical Power
POWER
ID SET
(WOOFER/REAR)
ENG - 5
NETWORK
SERVICE
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN 1
HDMI IN 2
Connecting the Soundbar to the Subwoofer
When the subwoofer is connected, you can enjoy rich bass sound.
Automatic connection between the Subwoofer and the Soundbar
When you turn the power on after connecting the power cables to the Soundbar and subwoofer, the
subwoofer is automatically connected to the Soundbar.
•• When auto pairing is complete, the blue indicators at the rear of the subwoofer turn on.
LED Indicator Lights on the Rear of Subwoofer
LED
Status
On
Description
Successfully connected
(normal operation)
Resolution
Check if the power cable attached to the
Blue
main Soundbar unit is connected properly
Blinking
Recovering the connection
or wait about 5 minutes. If blinking persists,
try manually connecting the subwoofer.
See page 7.
Red
On
Standby (with the Soundbar
Check if the power cable attached to the
main unit turned off)
main Soundbar unit is connected properly.
Connect again. See the instructions for
Connection failed
Red and
blue
Blinking
manual connection on page 7.
See the contact information for the
Malfunction
Samsung Service Centre in this manual.
ENG - 6
Manually connecting the Subwoofer if automatic connection fails
Before performing the manual connection procedure below:
•• Check whether the power cables for the Soundbar and subwoofer are connected properly.
•• Make sure that the Soundbar is turned on.
1. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds.
•• The red indicator on the rear of the subwoofer turns off and the blue indicator blinks.
5 Sec
Rear of Subwoofer
2. Press and hold the Up button on the remote control for at least 5 seconds.
•• The ID SET message appears on the display of the Soundbar for a moment, and then it
disappears.
•• The Soundbar will automatically power on when ID SET is complete.
5 Sec
PAIR
“Samsung Harman Kardon” logo is on the top
ID SET
ND
SOUODE
M
3. Check if the LINK LED is solid blue (connection complete).
The LINK LED indicator stops blinking and
glows a solid blue when a connection is
established between the Soundbar and the
Wireless Subwoofer.
Blue is On
ENG - 7
NOTES
•• Do not connect the power cord of this product or your TV to a wall outlet until all connections
between components are complete.
•• Before moving or installing this product, be sure to turn off the power and disconnect the power cord.
•• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the
STANDBY LED on the rear of the sub-woofer will turn red after blinking in blue several times.
•• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar,
interference may cause some sound interruption.
•• The maximum transmission distance of the main unit’s wireless signal is about 10 meters, but may
vary depending on your operating environment. If a steel-concrete or metallic wall is between the
main unit and the wireless subwoofer, the system may not operate at all because the wireless
signal cannot penetrate metal.
PRECAUTIONS
•• Wireless receiving antennas are built into the wireless subwoofer. Keep the unit away from water
and moisture.
•• For optimal listening performance, make sure that the area around the wireless subwoofer and the
Wireless Receiver Module (sold separately) is clear of any obstructions.
Connecting an SWA-9000S (Sold Separately) to your Soundbar
Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit
(SWA-9000S, sold separately) to your Soundbar.
1. Connect the Wireless Receiver Module to 2 Surround Speakers.
–– The speaker cables are colour coded.
L
SURROUND-LEFT
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
SURROUND-RIGHT
ID SET
L
R
SURROUND-LEFT
SURROUND-RIGHT
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE
: 3Ω
POWER
ID SET
ENG - 8
2. Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet.
•• The LINK LED indicator (blue LED) on the Wireless Receiver Module blinks. If the LED does not
blink, press the ID SET button on the back of the Wireless Receiver Module with a pen tip for
5~6 seconds until the LINK LED indicator blinks (in Blue). For more about the LED, please refer
to the SWA-9000S user manual.
STANDBY
SURROUND SPEAKERS OUT
SPEAKER
IMPEDANCE : 3Ω
L
R
5 Sec
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
STANDBY
ID SET
ID SET
LINK
LINK
POWER
Blue blinking
POWER
3. Press and hold the Up button on the remote control for at least 5 seconds.
•• The ID SET message appears on the display of the Soundbar for a moment, and then it
disappears.
•• The Soundbar will automatically power on when ID SET is complete.
5 Sec
PAIR
“Samsung Harman Kardon” logo is on the top
ID SET
ND
SOUODE
M
CAUTION
•• If your Soundbar was playing music when it connects to the SWA-9000S, you may hear some
stuttering from the woofer as the connection finalises.
4. Check if the LINK LED is solid blue (connection complete).
STANDBY
STANDBY
LINK
The LINK LED indicator stops blinking and
glows a solid blue when a connection is
LINK
established between the Soundbar and the
Wireless Receiver Module.
Blue is On
5. If the SWA-9000S is not connected, repeat the procedure from Step 2.
ENG - 9
04 CONNECTING TO YOUR TV
Hear TV sound from your Soundbar through wired or wireless connections.
•• When the Soundbar is connected to selected Samsung TVs, the Soundbar can be controlled using
the TV’s remote control.
–– This feature is available on 2017 and later Samsung Smart TVs that support Bluetooth when
the Soundbar is connected to the TV using an optical cable.
–– This function also allows you to use the TV menu to adjust the sound field and various settings
as well as the volume and mute.
Method 1. Connecting with a Cable
When the audio in a broadcast is encoded in Dolby Digital and the “Digital Output Audio Format” on
your TV is set to PCM, we recommend that you change the setting to Dolby Digital. When the setting on
the TV is changed, you will experience better sound quality. (The TV menu may use different words for
Dolby Digital and PCM depending on the TV manufacturer.)
Connecting a TV using an HDMI Cable
Connect to the HDMI IN
(ARC) port of your TV.
HDMI Cable
HDMI IN
(ARC)
Bottom of the Soundbar
HDMI OUT
(TV-ARC)
Connect to the HDMI OUT (TV-ARC)
port of the Soundbar main unit.
Top of the Soundbar
TV ARC
1. With the Soundbar and TV turned on, connect the HDMI cable as shown in the figure.
2. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV
sound.
•• If TV sound is inaudible, press the
(Source) button on the remote control or on the top of
the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence,
and TV sound is played.
ENG - 10
•• If “TV ARC” does not appear in the display window of the Soundbar main unit, confirm that the
HDMI cable is connected to the correct port.
•• Use the volume buttons on the TV’s remote control to change the volume on the Soundbar.
NOTES
•• HDMI is an interface that enables the digital transmission of video and audio data with just a single
connector.
•• If the TV provides an ARC port, connect the HDMI cable to the HDMI IN (ARC) port.
•• We recommend you use a coreless HDMI cable if possible. If you use a cored HDMI cable, use one
whose diameter is less than 14 mm.
•• Anynet+ must be turned on.
•• This function is not available if the HDMI cable does not support ARC.
Connecting using an Optical Cable
Optical Cable
Bottom of the Soundbar
(not supplied)
DIGITAL AUDIO IN
(OPTICAL)
OPTICAL OUT
Top of the Soundbar
HDMI IN 1
HDMI IN 2
D.IN
1. Connect the DIGITAL AUDIO IN (OPTICAL) jack on the Soundbar to the OPTICAL OUT jack of the TV
with a digital optical cable (not supplied).
2. Press the
(Source) button on the top panel or on the remote control, and then select the “D.IN”
mode.
ENG - 11
Auto Power Link
Auto Power Link automatically turns on the Soundbar when the TV is turned on.
1. Connect the Soundbar and a TV with a digital optical cable (not supplied).
2. Press the Left button on the remote control for 5 seconds to turn Auto Power
Link on or off.
•• Auto Power Link is set to ON by default.
(To turn off this function, press the Left button on the remote for 5 seconds.)
•• Depending on the connected device, Auto Power Link may not function.
•• This function is only available in the “D.IN” mode.
Method 2. Connecting Wirelessly
Connecting a TV via Bluetooth
When a TV is connected using Bluetooth, you can hear stereo sound without the hassle of cabling.
•• Only one TV can be connected at a time.
Top of the Soundbar
PAIR
OR
ND
SOUODE
M
The initial connection
1. Press the
PAIR button on the remote control to enter the “BT PAIRING” mode.
(OR) a. Press the
(Source) button on the top panel and then select “BT”.
“BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device
connected to the Soundbar.
b. When “BT READY” appears, press and hold the
(Source) button on the top panel of the
Soundbar for more than 5 seconds to display “BT PAIRING”.
2. Select Bluetooth mode on the TV. (For more information, see the TV’s manual.)
3. Select “[AV] Samsung Soundbar Q80R” from the list on TV’s screen.
An available Soundbar is indicated with “Need Pairing” or “Paired” on the TV’s Bluetooth device
list. To connect the TV to the Soundbar, select the message, and then establish a connection.
•• When the TV is connected, [TV Name] → “BT” appears on the Soundbar’s front display.
4. You can now hear TV sound from the Soundbar.
ENG - 12
If the device fails to connect
•• If a previously connected Soundbar (e.g. “[AV] Samsung Soundbar Q80R”) appears in the list, delete
it.
•• Then repeat steps 1 through 3.
NOTE
•• After you have connected the Soundbar to your TV the first time, use the “BT READY” mode to
reconnect.
Disconnecting the Soundbar from the TV
Press the
(Source) button on the top panel or on the remote control and switch to any mode but “BT”.
•• Disconnecting takes time because the TV must receive a response from the Soundbar.
(The time required may differ, depending on the TV model.)
•• To cancel the automatic Bluetooth connection between the Soundbar and TV, press the
p (Play/Pause) button on the remote control for 5 seconds with the Soundbar in “BT READY” status.
(Toggle On → Off)
What is the difference between BT READY and BT PAIRING?
•• BT READY : In this mode, you can search for previously connected TVs or connect a previously
connected mobile device to the Soundbar.
•• BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the
on the remote control or press and hold the
PAIR button
(Source) button on the top of the Soundbar for
more than 5 seconds while the Soundbar is in “BT” mode.)
NOTES
•• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
•• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
•• The Soundbar automatically turns off after 18 minutes in the Ready state.
•• The Soundbar may not perform Bluetooth search or connection correctly under the following
circumstances:
–– If there is a strong electrical field around the Soundbar.
–– If several Bluetooth devices are simultaneously paired with the Soundbar.
–– If the Bluetooth device is turned off, not in place, or malfunctions.
•• Electronic devices may cause radio interference. Devices that generate electromagnetic waves
must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.
ENG - 13
Connecting via Wi-Fi
Pre-connection Checklist
1. Confirm that your Samsung Smart TV was released after 2013. This function is compatible only
with Samsung Smart TVs released after 2013.
2. Make sure your Wireless router (Wi-Fi) is ready and working.
3. Make sure that the TV is connected to the Wireless router (your Wi-Fi network).
Top of the Soundbar
Step 1 : Connecting the Soundbar to Wi-Fi
1. Press the
(Source) button on the top of the Soundbar or on the remote control to select “WIFI”
mode.
•• When using selected Samsung TVs (2016 ~ 2018 Samsung Smart TVs that support Bluetooth.)
–– If you select “WIFI” mode when the TV is turned on, the TV screen displays a pop-up
window providing instructions on how to automatically connect the Soundbar to a wireless
router (Wi-Fi). Refer to the instructions in the pop-up window of the TV.
Top of the Soundbar
WIFI
2. Connect your mobile device (smartphone, tablet, etc.) to the Wi-Fi network the TV is connected to.
ENG - 14
3. Install and launch the SmartThings app on your mobile device (smartphone, tablet, etc.).
Android
iOS
SmartThings app
4. Follow the instructions in the app screen on the mobile device to connect the Soundbar to your
Wi-Fi network.
Step 2 : Configuring Settings on the TV
•• If the TV disconnects from your wireless network after you change the input source to the
Soundbar, use the TV menu to connect the TV to the network again.
For TVs released in 2019
Home (
)  Settings (
)  Sound  Sound Output  [AV] Samsung Soundbar Q80R (Wi-Fi)
For TVs released in 2018
Home (
)  Settings (
)  Sound  Sound Output  [AV] Samsung Soundbar Q80R (Wi-Fi)
For TVs released in 2017
Home (
)  Settings (
)  Sound  Sound Output  [AV] Samsung Soundbar Q80R (Wi-Fi)
For TVs released in 2016
Home (
)  Settings (
)  Sound  Select Speaker  [AV] Samsung Soundbar Q80R (Wi-Fi)
For TVs released in 2015
Menu  Sound  Speaker List
For TVs released in 2014
Menu  Sound  Speaker Settings  Multiroom Link - Settings
NOTES
•• The TV and Soundbar must be connected to the same wireless network (Wi-Fi).
•• If your wireless router (Wi-Fi) uses a DFS channel, you will not be able to establish a Wi-Fi
connection between the TV and Soundbar. Contact your Internet service provider for details.
•• If the 5GHz Wi-Fi connection is not smooth, use the 2.4GHz bandwidth.
•• Because the menus may differ depending on the year of manufacture, refer to your TV manual.
ENG - 15
05 CONNECTING AN EXTERNAL DEVICE
Connect to an external device via a wired or wireless network to play the external device’s sound
through the Soundbar.
Connecting using an HDMI Cable (Capable of Dolby Atmos decoding
and playback)
•• When you use Dolby Atmos®: If the input source is Dolby Atmos®, 5.1.2 channels are outputted.
When Dolby Atmos® is active, the Soundbar’s sound effect modes controlled by the SOUND MODE
button are not available.
•• Important: This product supports Dolby Atmos® only in HDMI mode.
Top of the Soundbar
HDMI 1
OR
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN 1
HDMI Cable
OR
HDMI OUT
HDMI IN 2
External Device
HDMI IN
(ARC)
HDMI 2
HDMI Cable
HDMI OUT
(TV-ARC)
Bottom of the Soundbar
1. Connect an HDMI cable from the HDMI IN 1 or HDMI IN 2 jack on the bottom of the Soundbar to the
HDMI OUT jack on your digital device.
2. Connect an HDMI cable from the HDMI OUT (TV-ARC) jack on the bottom of the Soundbar to the
HDMI IN jack on your TV.
3. Press the
(Source) button on the top panel or on the remote control, and then select
“HDMI 1” or “HDMI 2”.
4. “HDMI 1” or “HDMI 2” mode is displayed on the Soundbar display panel and sound plays.
ENG - 16
NOTE
•• When Dolby Atmos® is activated, “DOLBY ATMOS” appears in the front display.
Configuring Dolby Atmos® on your BD player or other device.
•• Open the audio output options on the settings menu of your BD player or other device and make
sure that “No Encoding” is selected for Bitstream. For example, on a Samsung BD Player, go to
Home Menu → Sound → Digital Output and then select Bitstream (unprocessed).
•• If the Audio Output options include Secondary Audio, make sure Secondary Audio is set to Off.
•• Make sure that the content supports Dolby Atmos®.
Connecting using an HDMI Cable
Top of the Soundbar
HDMI 1
OR
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN 1
HDMI Cable
OR
HDMI OUT
HDMI IN 2
External Device
HDMI IN
(ARC)
HDMI 2
HDMI Cable
HDMI OUT
(TV-ARC)
Bottom of the Soundbar
1. Connect an HDMI cable from the HDMI IN 1 or HDMI IN 2 jack on the bottom of the Soundbar to the
HDMI OUT jack on your digital device.
2. Connect an HDMI cable from the HDMI OUT (TV-ARC) jack on the bottom of the Soundbar to the
HDMI IN jack on your TV.
3. Press the
(Source) button on the top panel or on the remote control, and then select
“HDMI 1” or “HDMI 2”.
4. “HDMI 1” or “HDMI 2” mode is displayed on the Soundbar display panel and sound plays.
ENG - 17
Connecting using an Optical Cable
Top of the Soundbar
BD / DVD player / Set-top box /
Game console
D.IN
OPTICAL OUT
DIGITAL AUDIO IN
(OPTICAL)
Optical Cable
(not supplied)
Bottom of the Soundbar
1. Connect DIGITAL AUDIO IN (OPTICAL) on the main unit to the OPTICAL OUT jack of the Source
Device using a digital optical cable (not supplied).
2. Select “D.IN” mode by pressing the
(Source) button on the top panel or on the remote control.
ENG - 18
06 CONNECTING A MOBILE DEVICE
Connecting via Bluetooth
When a mobile device is connected using Bluetooth, you can hear stereo sound without the hassle of
cabling.
•• You cannot connect more than one Bluetooth device at a time.
Top of the Soundbar
PAIR
OR
Bluetooth device
ND
SOUODE
M
The initial connection
1. Press the
PAIR button on the remote control to enter the “BT PAIRING” mode.
(OR) a. Press the
(Source) button on the top panel and then select “BT”.
“BT” changes to “BT READY” in a few seconds automatically if there is no Bluetooth device
connected to the Soundbar.
b. When “BT READY” appears, press and hold the
(Source) button on the top panel of the
Soundbar for more than 5 seconds to display “BT PAIRING”.
2. On your device, select “[AV] Samsung Soundbar Q80R” from the list that appears.
•• When the Soundbar is connected to the Bluetooth device, [Bluetooth Device Name] → “BT”
appears in the front display.
3. Play music files from the device connected via Bluetooth through the Soundbar.
If the device fails to connect
•• If a previously connected Soundbar (e.g. “[AV] Samsung Soundbar Q80R”) appears in the list, delete
it.
•• Then repeat steps 1 and 2.
NOTE
•• After you have connected the Soundbar to your mobile device the first time, use the “BT READY”
mode to reconnect.
ENG - 19
What is the difference between BT READY and BT PAIRING?
•• BT READY : In this mode, you can search for previously connected TVs or connect a previously
connected mobile device to the Soundbar.
•• BT PAIRING : In this mode, you can connect a new device to the Soundbar. (Press the
on the remote control or press and hold the
PAIR button
(Source) button on the top of the Soundbar for
more than 5 seconds while the Soundbar is in “BT” mode.)
NOTES
•• If asked for a PIN code when connecting a Bluetooth device, enter <0000>.
•• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
•• The Soundbar automatically turns off after 18 minutes in the Ready state.
•• The Soundbar may not perform Bluetooth search or connection correctly under the following
circumstances:
–– If there is a strong electrical field around the Soundbar.
–– If several Bluetooth devices are simultaneously paired with the Soundbar.
–– If the Bluetooth device is turned off, not in place, or malfunctions.
•• Electronic devices may cause radio interference. Devices that generate electromagnetic waves
must be kept away from the Soundbar main unit - e.g., microwaves, wireless LAN devices, etc.
•• The Soundbar supports SBC data (44.1kHz, 48kHz).
•• Connect only to a Bluetooth device that supports the A2DP (AV) function.
•• You cannot connect the Soundbar to a Bluetooth device that supports only the HF (Hands Free)
function.
•• Once you have paired the Soundbar to a Bluetooth device, selecting “[AV] Samsung Soundbar
Q80R” from the device’s scanned devices list will automatically change the Soundbar to “BT” mode.
–– Available only if the Soundbar is listed among the Bluetooth device’s paired devices.
(The Bluetooth device and the Soundbar must have been previously paired at least once.)
•• The Soundbar will appear in the Bluetooth device’s searched devices list only when the Soundbar is
displaying “BT READY”.
•• The Soundbar cannot be paired to another Bluetooth device if already in Bluetooth mode and
paired to a Bluetooth device.
ENG - 20
Disconnecting the Bluetooth device from a Soundbar
You can disconnect a Bluetooth device from the Soundbar. For instructions, see the Bluetooth device’s
user manual.
•• The Soundbar will be disconnected.
•• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display
“BT DISCONNECTED” on the front display.
Disconnecting the Soundbar from the Bluetooth device
Press the
(Source) button on the top panel or on the remote control, and then change to any mode
except “BT”.
•• Disconnecting takes time because the Bluetooth device must receive a response from the
Soundbar. (Disconnection time may differ, depending on the Bluetooth device)
•• When the Soundbar is disconnected from the Bluetooth device, the Soundbar will display
“BT DISCONNECTED” on the front display.
NOTES
•• In Bluetooth connection mode, the Bluetooth connection will be lost if the distance between the
Soundbar and the Bluetooth device exceeds 10 meters.
•• The Soundbar automatically turns off after 18 minutes in the Ready state.
More About Bluetooth
Bluetooth is a technology that enables Bluetooth-compliant devices to interconnect easily with each
other using a short wireless connection.
•• A Bluetooth device may cause noise or malfunction, depending on usage, if:
–– A part of your body is in contact with the receiving/transmitting system of the Bluetooth
device or the Soundbar.
–– It is subject to electrical variation from obstructions caused by a wall, corner, or office partition.
–– It is exposed to electrical interference from same frequency-band devices including medical
equipment, microwave ovens, and wireless LANs.
•• Pair the Soundbar with the Bluetooth device while they are close together.
•• The further the distance between the Soundbar and Bluetooth device, the worse the quality is.
If the distance exceeds the Bluetooth operational range, the connection is lost.
•• In poor reception areas, the Bluetooth connection may not work properly.
•• The Bluetooth connection only works when it is close to the unit. The connection will be
automatically cut off if the Bluetooth device is out of range. Even within range, the sound quality
may be degraded by obstacles such as walls or doors.
•• This wireless device may cause electric interference during its operation.
ENG - 21
Connecting via Wi-Fi (Wireless Network)
•• Connect a single Soundbar to Wi-Fi to access a variety of music streaming services and Internet
radio. Connect multiple Soundbars to Wi-Fi to use grouped playback or the stereo sound mode.
•• To connect a Soundbar to a mobile device via a wireless network (Wi-Fi), the SmartThings app is
required.
Top of the Soundbar
Mobile device
The initial connection
1. Press the
(Source) button on the top of the Soundbar or on the remote control to select “WIFI”
mode.
Top of the Soundbar
WIFI
2. Install and launch the SmartThings app on your mobile device (e.g. smartphone or tablet).
Android
iOS
ENG - 22
SmartThings app
3. Launch the app, and then follow the instructions on the screen to register (add) your Soundbar in
the app.
•• The automatic pop-up (the third illustration below) may not be available on some mobile
devices.
If this is the case, select and complete “Add device” from the app menu . Your Soundbar is now
added to the app.
Launch App
Auto pop-up
Add speakers
NOTE
•• To connect an additional SWA-9000S wireless rear speaker kit (not supplied), disconnect the
Samsung wireless speakers from the Soundbar to disable the surround sound system. (If you
connect the surround speakers without disconnecting the SWA-9000S speakers, sound is played
via both the Samsung wireless speaker and the Surround speaker.)
ENG - 23
07 CONNECTING AN AMAZON PRODUCT
•• This feature may not be available in some countries.
•• This service is provided by Amazon and can be terminated at any time. Samsung does not assume
responsibility for service availability.
•• Amazon Alexa app screen is subject to change without prior notice.
Connect and use with an Amazon product (Amazon Echo)
Use an Amazon Echo product to control your Soundbar and enjoy music services provided by Amazon Echo.
NOTE
•• Confirm that the Soundbar is connected to Wi-Fi. (Refer to “Connecting via Wi-Fi (Wireless
Network)”)
1. In the SmartThings app, change your Soundbar’s name to one that can be recognized by your
Amazon device.
(Example: Samsung, Soundbar, Living Room, Family Room, Bedroom, Office, etc.)
CAUTION
•• Amazon devices may not recognize names that contain elements such as special characters.
Select Edit
Select speakers
ENG - 24
Change name
Save
2. In the Alexa app, search “Samsung Wireless Audio” in Skills, and then select “ENABLE”.
•• Skip this step if you have Skills set up already.
Amazon Alexa app
Select Skills
Search
ENG - 25
Enable
Use voice commands to control the Soundbar
•• The Amazon Echo service you can use with your Soundbar is limited to music. Other services
provided by Amazon Echo, such as news and weather, can only be accessed through your
Amazon Echo product.
Trigger + Command + Speaker name
Use the Speaker name you changed in the SmartThings app. (Refer to “Connect and use
with an Amazon product (Amazon Echo)”)
Action
Voice Command
To search an audio device added to the
SmartThings account connected to the
"Alexa Discover devices"
Amazon Alexa account
* To use voice commands for the Soundbar named “Living room”
Action
Voice Command
To set the volume level to 5
"Alexa Set the volume to 5 on Living room"
To increase the volume level
"Alexa Volume up on Living room"
To mute the sound
"Alexa Mute on Living room"
To listen to a radio station named KISS FM
"Alexa Play Kiss FM on Living room"
To play the next song
"Alexa Next song on Living room"
To stop the audio
"Alexa Stop on Living room"
To turn the audio on
"Alexa Turn on Living room"
To turn the audio off
"Alexa Turn off Living room"
To change the input source
"Alexa Switch to Bluetooth on Living room"
ENG - 26
08 USING THE REMOTE CONTROL
How to Use the Remote Control
Turns the Soundbar on and off.
Power
PAIR
Press to select a source connected to the
Soundbar.
Source
Mute
VOL
WOOFER
SOUND
MODE
PAIR
SOUND
MODE
You can select the desired sound mode by
choosing STANDARD, SURROUND, GAME PRO,
or ADAPTIVE SOUND.
SOUND MODE Select the “STANDARD” mode if you want to
enjoy the original sound.
•• GAME PRO mode
PAIR
PAIR yourself in the scene with a
Immerse
dedicated
VOL
WOOFER setting that optimizes sounds
SOUND
specifically for gaming.
WOOFER
SOUND
MODEVOL
MODE
•• ADAPTIVE SOUND mode
Automatically analyzes content and gives
you optimized sound and automatically
enhances voice clarity on low volumes.
SOUND
MODE
Press the
(Mute) button to mute the sound.
Press it again
PAIR to unmute the sound.
SOUNDBAR
PAIR
VOL
WOOFER
VOL
Bluetooth
SOUND
MODE
VOL
PAIR
WOOFER
ENG - 27
Press the PAIR button. “BT PAIRING” appears
in the Soundbar’s display.
You can connect the Soundbar to a new
WOOFER
Bluetooth device in this mode by selecting the
Soundbar from the Bluetooth device's search
list.
Press the p button to pause a music file temporarily.
When you press the button again, the music file plays.
Play / Pause
(BT/Wi-Fi)
PAIR
Press the indicated areas to select Up/Down/Left/Right.
SOUND
MODE
Up/Down/
PAIR
Left/Right
SOUND
MODE
VOL
VOL
WOOFER
WOOFER
Press Up/Down/Left/Right on the button to select or set functions.
•• Music Skip
Press the Right button to select the next music file. Press the Left button to select the
previous music file.
•• Anynet+ / Auto Power Link
You can turn Anynet+ and Auto Power Link on or off.
Anynet+ and Auto Power Link are turned on and turned off by the Right and Left
buttons respectively.
–– Anynet+ : If the Soundbar is connected to a Samsung TV through an HDMI cable,
you can control your Soundbar with a Samsung TV remote control.
Press and hold the Right button for 5 seconds to toggle Anynet+ ON and OFF.
–– Auto Power Link : If the Soundbar is connected to your TV through a digital optical
cable, the Soundbar can automatically turn on when you turn on your TV. Press
and hold the Left button for 5 seconds to toggle Auto Power Link ON and OFF.
–– Anynet+ / Auto Power Link are set to ON by default.
•• ID SET
Press and hold the Up button for 5 seconds to complete ID SET (when connecting to an
accessary item).
ENG - 28
You can select TREBLE, BASS, SYNC, CENTER LEVEL, SIDE LEVEL, FRONT TOP LEVEL,
REAR LEVEL, and VIRTUAL ON/OFF.
–– To control the volume of the treble or bass sound, select TREBLE or BASS in Sound
Sound Control
Settings, and then adjust the volume between -6~+6 by using the Up/Down buttons.
–– Press and hold the
(Sound Control) button for about 5 seconds to adjust the sound
for each frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz, 2.5kHz, 5kHz, and 10kHz are
selectable using the Left/Right buttons and each can be adjusted to a setting
between -6 to +6 using the Up/Down buttons.
–– To control the volume of the each speaker select CENTER LEVEL, SIDE LEVEL or
FRONT TOP LEVEL in Sound Settings, and then adjust the volume between -6~+6 by
using the Up/Down buttons.
–– If the video on the TV and audio from the Soundbar are not synchronised, select SYNC
in Sound Control, and then set the audio delay between 0~300 milliseconds by using
the Up/Down buttons.
–– If Surround Speakers are connected, select REAR LEVEL and then use the Up/Down
PAIR
buttons to adjust the volume within a -6 to +6 range. The VIRTUAL Speaker function
PAIR
can be turned ON/OFF by using the Up/Down buttons.
–– SYNC is only supported for some functions.
SOUND
MODE
•• Initialise
SOUND
MODE
With the Soundbar turned off, press and hold the
(Sound Control) button for more
than 5 seconds until the speaker turns on. “INIT” appears on the display and the
Soundbar is initialised.
R
FE
FE
W
OO
W
OO
SO
U
N
VO
L
D
BA
R
BA
R
D
SO
VO
L
D
N
U
WOOFER
SO
O
U
N
VO
L
D
BA
R
BA
R
W
OO
SOUND
VOLMODE
N
OO
FE
FE
R
R
SO
M UN
OD D
E
SO
M UN
OD D
E
SO
M UN
OD D
E
PAIR
WOOFER
WOOFER
R
VOL
U
Push the button up or down to adjust the volume of the subwoofer to -12 or between -6 to
+6. To set the subwoofer volume level to 0, press the button.
W
OO
FE
BA
R
D
N
U
SO
VO
L
N
D
U
SO
SO
U
N
VO
L
D
BA
R
BA
R
W
OO
W
OO
F
FE
ER
R
SO
M UN
OD D
E
SO
M UN
OD D
E
SO
M UN
OD D
E
R
WOOFER
VO
L
VOL
VOL
SO
M UN
OD D
E
Push the button up or down to adjust the volume.
•• Mute
Press the VOL button to mute the sound. Press it again to unmute the sound.
ENG - 29
Adjusting the Soundbar volume
with a TV remote control
4. If you want to return the Soundbar to the
If you have a Samsung TV, you can adjust
the Soundbar’s volume using the IR remote
control that came with your Samsung TV.
button for 5 seconds repeatedly until
default mode (control by a Samsung TV
remote), push up and hold the WOOFER
“SAMSUNG-TV REMOTE” appears in the
display.
First use the TV menu to set the TV audio on your
(Default mode)
Samsung TV to external speakers, then use your
5 Sec
SO
M UN
OD D
E
Samsung remote to control the Soundbar’s
FE
W
OO
BA
R
D
N
U
SO
VO
L
manual. The default mode for this function is
SAMSUNG-TV REMOTE
R
volume. For more information, see the TV’s user
control by a Samsung TV remote. If your TV is not
a Samsung TV, follow the directions below to
change the settings of this function.
1. Turn Off the Soundbar.
BYE
–– Each time you push the WOOFER button
up and hold it for 5 seconds, the mode
switches in the following order:
“SAMSUNG-TV REMOTE” (Default mode)
→ “OFF‑TV REMOTE” → “ALL‑TV REMOTE”.
–– This function may not be available,
depending on the remote control.
–– Manufacturers supporting this function:
VIZIO, LG, Sony, Sharp, PHILIPS,
2. If you do not want to use this function, push
up and hold the WOOFER button for
5 seconds repeatedly until “OFF-TV
REMOTE” appears in the display.
OFF-TV REMOTE
N
D
SO
U
VO
L
BA
R
W
OO
FE
R
SO
M UN
OD D
E
5 Sec
3. If you want to control the Soundbar with
your TV’s remote, push up and hold the
WOOFER button for 5 seconds repeatedly
until “ALL-TV REMOTE” appears in the
display. Then, use your TV’s menu to select
external speakers.
ALL-TV REMOTE
D
U
N
SO
VO
L
BA
R
W
OO
FE
R
SO
M UN
OD D
E
5 Sec
ENG - 30
PANASONIC, TOSHIBA, GRUNDIG,
Hisense, RCA
Using the Hidden Buttons (Buttons with more than one function)
Hidden Button
Reference page
Remote Control Button
Function
WOOFER
TV remote control On/Off (Standby)
page 30
Left
Auto Power Link ON/OFF
page 28
Right
Anynet+ ON/OFF
page 28
Up
(Sound Control)
ID SET
page 28
7 Band EQ
page 29
Initialise (Standby)
page 29
Output specifications for the different sound effect modes
Output
Effect
STANDARD
SURROUND
GAME PRO
ADAPTIVE SOUND
Input
With Subwoofer Only
With Subwoofer & Wireless
Rear Speaker Kit
2.0 ch
2.1 ch
2.1 ch
5.1 ch
5.1 ch
5.1 ch / 7.1 ch (DTS)
7.1 ch
5.1 ch
7.1 ch
7.1.4 ch
5.1.2 ch
7.1.2 ch
2.0 ch
5.1.2 ch
7.1.2 ch
5.1 ch
5.1.2 ch
7.1.2 ch
7.1 ch
5.1.2 ch
7.1.2 ch
7.1.4 ch
5.1.2 ch
7.1.2 ch
2.0 ch
5.1.2 ch
7.1.2 ch
5.1 ch
5.1.2 ch
7.1.2 ch
7.1 ch
5.1.2 ch
7.1.2 ch
7.1.4 ch
5.1.2 ch
7.1.2 ch
2.0 ch
5.1.2 ch
7.1.2 ch
5.1 ch
5.1.2 ch
7.1.2 ch
7.1 ch
5.1.2 ch
7.1.2 ch
7.1.4 ch
5.1.2 ch
7.1.2 ch
•• If the input source is Dolby Atmos®, 5.1.2 channels are outputted. The sound effect modes
controlled by the SOUND MODE button and listed above are not available.
•• The Samsung Wireless Rear Speaker Kit can be purchased separately. To purchase a Kit, contact the
vendor you purchased the Soundbar from.
ENG - 31
09 INSTALLING THE
WALL MOUNT
Wallmount Components
Wall Mount Guide
Installation Precautions
x2
x2
•• Install on a vertical wall only.
(M4 x L10)
•• Do not install in a place with high
Holder-Screw
temperature or humidity.
•• Verify whether the wall is strong enough to
Screw
x2
support the product’s weight. If not, reinforce
the wall or choose another installation point.
•• Purchase and use the fixing screws or
Bracket-Wall Mount
anchors appropriate for the kind of wall you
have (plaster board, iron board, wood, etc.). If
possible, fix the support screws into wall
1. Place the Wall Mount Guide against the wall
studs.
•• Purchase wall mounting screws according to
the type and thickness of the wall you want to
mount the Soundbar on.
surface.
•• The Wall Mount Guide must be level.
•• If your TV is mounted on the wall, install
the Soundbar at least 5 cm below the TV.
–– Diameter: M5
–– Length: 35 mm or longer recommended.
•• Connect cables from the unit to external
devices before you install the Soundbar on
the wall.
•• Make sure the unit is turned off and
5 cm or more
unplugged before you install it. Otherwise, it
may cause an electric shock.
ENG - 32
2. Align the Wall Mount Guide’s Centre Line
5. Push a screw (not supplied) through each
with the centre of your TV (if you are
Holder-Screw, and then screw each screw
mounting the Soundbar below your TV), and
firmly into a support screw hole.
then fix the Wall Mount Guide to the wall
using tape.
•• If you are not mounting below a TV, place
the Centre Line in the centre of the
installation area.
6. Install the 2 Bracket-Wall Mounts in the
correct orientation on the bottom of the
Soundbar using 2 Screws.
Centre Line
3. Push a pen tip or sharpened pencil tip
through the centre of the A-TYPE images on
each end of the Guide to mark the holes for
the supporting screws, and then remove the
Wall Mount Guide.
•• When assembling, make sure the hanger
part of the Bracket-Wall Mounts are
located behind the rear of the Soundbar.
4. Using an appropriately sized drill bit, drill a
Rear of Soundbar
hole in the wall at each marking.
•• If the markings do not correspond to the
positions of studs, make sure you insert
appropriate anchors or mollies into the
holes before you insert the support
screws. If you use anchors or mollies,
make sure the holes you drill are large
enough for the anchors or mollies you
Right end of Soundbar
use.
ENG - 33
7. Install the Soundbar with the attached
Bracket-Wall Mounts by hanging the
Bracket-Wall Mounts on the Holder-Screws
on the wall.
10 INSTALLING THE
SOUNDBAR
ABOVE A TV
STAND
Component
8. Slide the Soundbar down as shown below so
x4
that the Bracket-Wall Mounts rest securely
on the Holder-Screws.
Rubber-Foot
•• Insert the Holder-Screws into the wide
(bottom) part of the Bracket-Wall
Mounts, and then slide the Bracket-Wall
Mounts down so that the Bracket-Wall
Mounts rest securely on the
Holder-Screws.
You can install the Soundbar above TV stands
that are less than 7.6 cm in height. To install,
attach the Rubber-Feet to the bottom of the
Soundbar before placing it in position above the
TV stand. Make sure you attach the Rubber-Feet
so that they are beyond the outside edges of the
TV stand. Refer to the figure below.
Rubber-Foot
ENG - 34
11 SOFTWARE
UPDATE
When the Soundbar is connected to the Internet,
software updates automatically occur even when
the Soundbar is turned off.
•• To use the Auto Update function, the
Soundbar must be connected to the Internet.
The Wi-Fi connection to the Soundbar will be
terminated if the Soundbar’s power cord is
disconnected or the power is cut off. If the
power is cut off, when the power comes back
on or you reconnect the power cord, turn on
the Soundbar, and then reconnect it to the
Internet.
ENG - 35
12 TROUBLESHOOTING
Before seeking assistance, check the following.
The red LED on the subwoofer blinks and
the subwoofer is not producing sound.
The unit will not turn on.
Is the power cord plugged into the outlet?
This issue can occur if the subwoofer is not
;; Connect the power plug to the outlet.
connected to the Soundbar main unit.
A function does not work when the button
is pressed.
;; Try to connect your subwoofer again.
Is there static electricity in the air?
The subwoofer drones and vibrates
noticeably.
;; Disconnect the power plug and connect it
again.
(See page 6.)
Try to adjust the vibration of your subwoofer.
;; Push the WOOFER button on your remote
Sound dropouts occur in BT mode.
control up or down to adjust the subwoofer
;; See the Bluetooth connection sections on
volume. (to -12, or between -6 ~ +6).
pages 12 and 19.
Cannot connect to the TV.
Sound is not produced.
If connected via a wired network
;; Check if the cable is connected correctly.
Is the Mute function on?
;; Press the
–– Check the port name to make sure
(Mute) button to cancel the
that the cable is connected to the
mute function.
correct port. For instructions, see the
Is the volume set to minimum?
page explaining each connection
;; Adjust the Volume.
method.
The remote control does not work.
;; Press the
Are the batteries drained?
control to check if the mode is correct.
;; Replace with new batteries.
Is the distance between the remote control and
Soundbar main unit too far?
(Source) button on the top
panel of the Soundbar or on the remote
If connected via a wireless network
;; Connected via Bluetooth
1. Switch the Soundbar to “BT PAIRING”
;; Move the remote control closer to the
mode, and then use the TV to search
Soundbar main unit.
again. (See page 12 for details.)
ENG - 36
13 LICENCE
;; Connected via Wi-Fi
1. Check if the TV is a compatible model.
•• Only Samsung Smart TVs released
after 2013 are supported.
2. Check if the TV is connected to Wi-Fi.
•• If the TV is not connected to Wi-Fi, use
the network menu on the TV to
Manufactured under license from Dolby
Laboratories. Dolby, Dolby Atmos, Dolby Audio,
establish a connection. (See the TV
Dolby Digital Plus, Pro Logic, and the double-D
user manual.)
symbol are trademarks of Dolby Laboratories.
3. Check if the Soundbar is connected to
Wi-Fi.
•• When the Soundbar is connected, you
can find it in the list of speakers on
For DTS patents, see http://patents.dts.com.
your mobile device when you run the
Manufactured under license from DTS
SmartThings app. See page 22 for
details.
4. Check for a DFS channel.
•• If your wireless router (Wi-Fi) is using a
DFS channel, you cannot establish a
Wi-Fi connection between the TV and
Soundbar. Contact your Internet
service provider for details.
Licensing Limited. DTS, the Symbol, & DTS and
the Symbol together, DTS:X, and the DTS:X logo
are registered trademarks and/or trademarks
of DTS, Inc. in the United States and/or other
countries. © DTS, Inc. All Rights Reserved.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
•• The Spotify Software is subject to third
party licences found here :
www.spotify.com/connect/third-partylicenses.
•• For more information about Spotify
Connect, please visit
www.spotify.com/connect
ENG - 37
14 OPEN SOURCE
LICENCE NOTICE
For further information on Open Sources used in
this product, please visit the website:
http://opensource.samsung.com
15 IMPORTANT
NOTES ABOUT
SERVICE
Figures and illustrations in this User Manual are
provided for reference only and may differ from
actual product appearance.
ENG - 38
16 SPECIFICATIONS AND GUIDE
Specifications
Model Name
HW-Q80R
Weight
8.8 kg
Dimensions (W x H x D)
1226.0 x 83.0 x 136.0 mm
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % ~ 75 %
AMPLIFIER
Rated Output power
Supported play formats
18W x 10 + 10W x 3, 4ohm
LPCM 8ch, Dolby Digital,
Dolby Atmos (True HD / Digital Plus), DTS:X
Subwoofer Name
PS-WR75B
Weight
9.8 kg
Dimensions (W x H x D)
205.0 x 403.0 x 403.0 mm
AMPLIFIER
Rated Output power
160W
NOTES
•• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
•• Weight and dimensions are approximate.
•• HW-Q80R: AC110-240V ~ 50/60Hz, 35W
•• PS-WR75B: AC110-240V ~ 50/60Hz, 28W
Precaution : The Soundbar will restart automatically if you turn on/turn off Wi-Fi.
Wi-Fi
Port deactivation method
Bluetooth
Port deactivation method
Press the ID SET button on the bottom panel of the
Soundbar for 30 seconds to turn Wi-Fi On / Off.
Press the NETWORK button on the bottom panel of the
Soundbar for 30 seconds to turn Bluetooth On / Off.
ENG - 39
安全資訊
安全警告
警告
為減少觸電的危險，請勿取下機蓋（或後蓋）。
本裝置內部沒有使用者可自行維修的零件。請
讓合格的維修人員進行維修。
請參閱以下表格，查看可能出現在
Samsung 產品上的符號說明。
注意
存在觸電的危險，
請勿打開
此符號表示內部有高壓電。
以任何方式碰觸本產品的任何內部
零件均有危險。
此符號表示本產品隨附關於操作與
維護的重要說明文件。
II 類產品：此符號表示不需要連接
接地。
若此符號沒有出現在含電源線的產
品上，則該產品必須牢固連接至保
護性接地 (地線)。
• 為降低發生火災或觸電的風險，請勿使
本裝置淋雨或將其放置在潮濕的環境
中。
注意
• 為避免觸電，請將插頭的寬插腳對準寬
插槽並將它完全插入。
• 本裝置一律要連接至帶有保護接地連接
的交流電源插座。
• 要斷開本裝置的電源，必須從電源插座
上拔下插頭，因此電源插頭應該易於操
作。
• 請勿使本裝置滴到水或濺到水。請勿在
本裝置上放置裝有液體的物件，如花
瓶。
• 若要完全關閉本裝置，必須從牆上插座
拔下電源插頭。因此，電源插頭必須隨時
都可輕鬆快速拔插。
AC 電壓：此符號表示額定電壓的
標記為 AC 電壓。
DC 電壓：此符號表示額定電壓的
標記為 DC 電壓。
注意，使用時須參照說明指示：此
符號指示用戶查閱使用者手冊以取
得進一步的安全相關資訊。
TPE - ii
注意事項
1. 請確保家中的交流電符合本產品底部的
識別貼紙上所列的電源要求。產品水平
安裝在平台（傢俱）上，並在周圍留出足
夠的空間用於通風 7~10 公分。請確保
通風槽沒有被遮擋。不要將裝置放置在
放大器或可能會變熱的裝置上。本裝置
設計為可以連續使用。
若要完全關閉裝置，請從牆上插座拔下
交流電源插頭。如果您打算長時間不使
用裝置，請拔下裝置的電源插頭。
2. 在雷暴期間，請從牆上插座拔下交流電
源轉接器。閃電造成的電壓尖峰可能會
損壞裝置。
3. 不要將裝置放置在陽光直射到的位置
或靠近熱源的位置。這可能導致產品過
熱，從而使得裝置發生故障。
4. 避免產品受潮（例如遠離 花瓶）、遠離
高熱位置（例如壁爐）或會形成強磁場
或電場的裝置。如果裝置發生故障，請
從交流電源插座中拔下電源插頭。本產
品並非設計為供工業使用。僅限個人使
用。如果您的產品貯藏在寒冷的溫度
中，則可能會發生冷凝。如果在冬天運
輸裝置，請靜候約 2 小時，直到裝置達
到室溫後再使用。
5. 與產品配合使用的電池含有對環境有害
的化學物品。 請勿將電池放入一般家庭
垃圾筒中。請勿將電池置於火中。不要
使電池短路、分解或過熱。若沒有正確
更換電池，將會有爆炸的危險。 請使用
相同類型的電池來更換。
關於本手冊
使用者手冊具有兩個部分：這份內容簡要的
「使用者手冊」以及可下載的詳細「完整手
冊」。
使用者手冊
查看本手冊可瞭解安全說明、產品安裝、
元件、連線和產品規格。
完整手冊
您可以在 Samsung 的線上客戶支援中心
掃描 QR 代碼，以取得完整手冊。若要在
電腦或行動裝置上查看手冊，請從
Samsung 網站以文件格式下載手冊。
(http://www.samsung.com/support)
設計和規格以及「應用程式」畫面可能
會隨時變更，恕不另行通知。
TPE - iii
目錄
01
檢查元件
02
產品概覽
在使用遙控器前插入電池 (AA 電池 X 2)
5
連接有源音箱
------------------------- 5
連接電力
將有源音箱連接至有源重低音音箱
– 有源重低音音箱和有源音箱之間的自動連線
– 若自動連線失敗，請手動連線有源重低音音箱
將 SWA-9000S (分售) 連接至有源音箱
連接至您的電視
方法 1。以纜線連接
------------------------- 7
------------------------- 8
10
------------------------- 11
– 使用光纖纜線連接
方法 2。無線連線
------------------------- 12
------------------------- 12
– 透過藍牙連線電視
– 透過 Wi-Fi 連線
------------------------- 14
連線外部裝置
使用 HDMI 纜線連接 (能夠使用 Dolby Atmos 解碼和播放)
使用 HDMI 纜線連接
16
------------------------- 16
------------------------- 17
------------------------- 18
使用光纖纜線連接
06
------------------------- 6
------------------------- 6
------------------------- 10
------------------------- 10
– 使用 HDMI 纜線連接電視
05
3
------------------------- 4
有源音箱底部面板
04
------------------------- 2
------------------------- 3
有源音箱前方面板/上方面板
03
2
19
連線行動裝置
------------------------- 19
透過藍牙連線
透過 Wi-Fi (無線網路) 連線
TPE - iv
------------------------- 22
07
連接 Amazon 產品
連接並搭配 Amazon 產品 (Amazon Echo) 使用
使用語音命令控制有源音箱
08
------------------------- 27
透過電視遙控器調整有源音箱音量
------------------------- 30
32
安裝掛牆托架
------------------------- 32
------------------------- 32
牆面安裝元件
將有源音箱安裝在電視架上
13
14
15
16
34
------------------------- 34
元件
12
------------------------- 31
------------------------- 31
安裝注意事項
11
------------------------- 26
如何使用遙控器
適用於不同音效模式的輸出規格
10
------------------------- 24
27
使用遙控器
使用隱藏按鈕 (具有多種功能的按鈕)
09
24
35
軟體更新
36
疑難排解
37
授權
開放式原始碼授權聲明
38
38
關於維修的重要說明
39
規格和指南
------------------------- 39
規格
TPE - v
01 檢查元件
PAIR
SOUND
MODE
VOL
WOOFER
SOUNDBAR
有源音箱主裝置
1
遙控器/電池
有源重低音音箱
2
x2
電線 (有源重低音音箱)
電線 (主裝置)
x2
牆面安裝導桿
•
•
•
•
支撐螺絲
HDMI 纜線
x2
(M4 x L10)
螺絲
掛牆托架
x4
橡膠墊
電源和消耗功率，請參考本產品上的標籤。(標籤 : 有源音箱主裝置底部)
電力連接步驟以標籤顯示 (1、2)。如需更多關於電力連接的資訊，請參見第 5 頁。
若要購買其他元件或選用纜線，請洽詢 Samsung 服務中心或是 Samsung 客戶服務。
配件的外觀可能與上面的圖例略有差異。
在使用遙控器前插入電池 (AA 電池 X 2)
依箭頭方向滑動電池蓋，直到完全拆下為止。
按照正確的電極方向插入 2 個 AA 電池 (1.5V)。
將電池蓋滑動回正確的位置。
TPE - 2
02 產品概覽
有源音箱前方面板/上方面板
以正確方式放置產品，
讓「Samsung Harman
Kardon」標誌位於上方。
上方
面板
(電源) 按鈕
開啟及關閉電源。
• Auto Power Down 功能
裝置會在下列情況自動關閉。
– D.IN / HDMI 1 / HDMI 2 / WIFI / BT 模式：若連續 18 分鐘都沒有音訊訊號。
(訊號源) 按鈕
選擇訊號源輸入模式。
輸入模式
顯示器
D.IN
光纖數位數入
ARC (HDMI OUT) 輸入
D.IN → TV ARC (自動轉換)
Wi-Fi 模式
WIFI
HDMI 輸入
HDMI 1 / HDMI 2
BT
藍牙模式
-/+ (音量) 按鈕
調整音量。
• 調整時，音量等級會顯示在有源音箱前方顯示器上。
顯示器
顯示產品狀態和目前模式。
• 您插入交流電源線後，電源鍵會 4 到 6 秒鐘內生效。
• 當您開啟本裝置時，可能會延遲 4 到 5 秒後，裝置才會發出聲音。
• 如果您只想從有源音箱欣賞聲音，則必須從電視的 音訊設定 選單中關閉電視的揚聲
器。請參閱電視隨附的使用者手冊。
TPE - 3
有源音箱底部面板
POWER
POWER
DIGITAL AUDIO IN DIGITAL AUDIO IN
(OPTICAL)
(OPTICAL)
SERVICE
POWER
SERVICE
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
ID SET
(WOOFER/REAR)
ID SET
(WOOFER/REAR)
ID SET
(WOOFER/REAR)
NETWORK
NETWORK
NETWORK
HDMI IN 1
HDMI IN 1
HDMI IN 1
HDMI IN 2
HDMI IN 2
HDMI IN 2
HDMI OUT
(TV-ARC)
HDMI OUT
(TV-ARC)
HDMI OUT
(TV-ARC)
POWER
POWER
POWER
ID SET
ID SET
ID SET
(WOOFER/REAR)
(WOOFER/REAR)
(WOOFER/REAR)
SERVICE
SERVICE
SERVICE
HDMI
HDMI
INHDMI
IN
1 1 IN 1
HDMI
HDMI
INHDMI
IN
2 2 IN 2
NETWORK
NETWORK
NETWORK
DIGITAL
DIGITAL
DIGITAL
AUDIO
AUDIO
AUDIO
IN IN IN
(OPTICAL)
(OPTICAL)
(OPTICAL)
HDMI
HDMI
OUT
HDMI
OUT OUT
(TV-ARC)
(TV-ARC)
(TV-ARC)
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
POWER
ID SET
(WOOFER/REAR)
HDMI IN 1
NETWORK
HDMI IN 2
HDMI OUT
(TV-ARC)
POWER
連接有源音箱的交流電源線
。
POWER
SERVICE
DIGITAL AUDIO IN
(OPTICAL)
ID SET
ID SET (WOOFER/REAR)
(WOOFER/REAR)
HDMI IN 2
按下以無線方式將有源音箱連接至環場音效揚聲器和有源重低音音箱。
NETWORK
• 按住遙控器上的向上按鈕 5 秒以完成 ID SET。
NETWORK
按下以透過 SmartThings 應用程式連線至無線網路 (Wi-Fi)。
HDMI IN 1
HDMI OUT
(TV-ARC)
SERVICE
連接 USB 儲存裝置以升級產品軟體。
DIGITAL AUDIO IN (OPTICAL)
連接至外部裝置的數位 (光纖) 輸出。
HDMI IN 1 / HDMI IN 2
使用 HDMI 纜線同時輸入數位視訊和音訊訊號。
連接至外部裝置的 HDMI 輸出。
HDMI OUT (TV-ARC)
連接至電視上的 HDMI (ARC) 插孔。
• 從牆壁插座拔除電源線時，請拉動插頭。請勿拉動纜線。
• 在完成元件之間的所有連接之前，請勿將此裝置或其他元件連接至交流電插座。
TPE - 4
03 連接有源音箱
連接電力
使用電源元件 (1、2) 以下列順序將有源重低音音箱、環場音效揚聲器和有源音箱連接至
電源插座：
1 將電源線連接至有源重低音音箱。
2 將電源線連接至有源音箱。
請參見下圖。
• 電源和消耗功率，請參考本產品上的標籤。(標籤 : 有源音箱主裝置底部)
1 電線
POWER
連接電力
有源重低音音箱
後側
POWER
POWER
2 電線
DIGITAL AUDIO IN
(OPTICAL)
SERVICE
POWER
ID SET
(WOOFER/REAR)
HDMI IN 1
NETWORK
HDMI IN 2
HDMI OUT
(TV-ARC)
有源音箱主裝置底部
連接電力
POWER
ID SET
(WOOFER/REAR)
TPE - 5
NETWORK
SERVICE
DIGITAL AUDIO IN
(OPTICAL)
HDMI IN 1
HDMI IN 2
將有源音箱連接至有源重低音音箱
連接有源重低音音箱後，即可享受豐富的低音音效。
有源重低音音箱和有源音箱之間的自動連線
將電纜連接至有源音箱和有源重低音音箱之後，再開啟電源時，有源重低音音箱會自動連
線至有源音箱。
• 自動配對完成後，有源重低音音箱後側的藍色指示燈會亮起。
有源重低音音箱後側的 LED 指示燈亮起
LED
狀態
亮
藍色
紅色
紅色和
藍色
閃爍
說明
解決方案
成功連線 (正常運作)
-
正在恢復連線
檢查連接至有源音箱主裝置的電源線
是否正確連接，或等待大約 5 分鐘。
若持續閃爍，請嘗試手動連線有源重
低音音箱。請參閱第 7 頁。
待命 (有源音箱主裝置關閉)
檢查連接至有源音箱主裝置的電纜是
否正確連接。
連接失敗
重新連線。請參見第 7 頁的手動
連線說明。
故障
請查看手冊中 Samsung 服務中心的
聯絡資訊。
亮
閃爍
TPE - 6
若自動連線失敗，請手動連線有源重低音音箱
在執行手動連線之前，請進行以下程序：
• 檢查有源音箱和有源重低音音箱之間的電纜是否正確連接。
• 確認有源音箱為開啟。
1. 按住有源重低音音箱後側的 ID SET 至少 5 秒。
• 有源重低音音箱後側的紅色指示燈會關閉，而且藍色指示燈會閃爍。
5 Sec
有源重低音音箱後側
2. 按住遙控器上的向上按鈕至少 5 秒。
• ID SET 訊息會短暫地出現在有源音箱的顯示器上，然後消失。
• 有源音箱將會在 ID SET 完成後自動開啟電源。
「Samsung Harman Kardon」
標誌位於上方
5 Sec
PAIR
ID SET
ND
SOUODE
M
3. 檢查 LINK LED 燈是否持續亮著藍燈 (連線完成)。
有源音箱和無線有源重低音音箱之間建
立連線後，LINK LED 指示燈就會停止
閃爍，並持續亮著藍燈。
藍燈亮起
TPE - 7
附註
• 在完成元件之間的所有連接之前，請勿將本產品電線或電視連接至牆面插座。
• 在移動或安裝本產品之前，務必關閉電源並拔除電線。
• 如果主裝置已關閉電源，無線有源重低音音箱將會進入待機模式，而且後面的
STANDBY LED 燈將會在閃爍藍燈數次後呈現紅色。
• 若您在有源音箱附近使用頻率 (5.8GHz) 與有源音箱相同的裝置，干擾可能會造成聲音
中斷。
• 主裝置無線訊號的最大發射距離約為 10 公尺，但可能因不同的操作環境而異。若鋼筋
水泥或金屬牆位於主裝置和無線有源重低音音箱之間，則系統可能完全無法操作，因為
無線訊號無法穿透金屬。
注意事項
• 無線接收天線內建於無線有源重低音音箱。讓裝置遠離水和濕氣。
• 為達到最佳的聆聽效能，請確認無線有源重低音音箱和無線接收器模組（分售）位置的
週圍區域沒有任何障礙物。
將 SWA-9000S (分售) 連接至有源音箱
透過將 Samsung 無線後置揚聲器套件 (SWA-9000S，另售) 連接至有源音箱，可擴大至逼
真的無線環場音效。
1. 將無線接收器模組連接至 2 個環場揚聲器。
– 揚聲器纜線以顏色編碼。
L
SURROUND-LEFT
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
SURROUND-RIGHT
ID SET
L
R
SURROUND-LEFT
SURROUND-RIGHT
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE
: 3Ω
POWER
ID SET
TPE - 8
2. 在插入電源插座後，檢查無線接收器模組是否處於待命狀態。
• 無線接收器模組上的 LINK LED 指示燈 (藍色 LED 燈) 會閃爍。若 LED 燈沒有閃
爍，請使用筆尖按住無線接收器模組背面的 ID SET 按鈕 5~6 秒，直到 LINK LED
指示燈閃爍 (藍色) 為止。如需更多關於 LED 燈的資訊，請參閱 SWA-9000S 使用者
手冊。
STANDBY
SURROUND SPEAKERS OUT
SPEAKER
IMPEDANCE : 3Ω
L
R
5 Sec
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
STANDBY
ID SET
ID SET
LINK
POWER
LINK
藍燈閃爍
POWER
3. 按住遙控器上的向上按鈕至少 5 秒。
• ID SET 訊息會短暫地出現在有源音箱的顯示器上，然後消失。
• 有源音箱將會在 ID SET 完成後自動開啟電源。
「Samsung Harman Kardon」
標誌位於上方
5 Sec
PAIR
ID SET
ND
SOUODE
M
注意
• 若您的有源音箱在連線至 SWA-9000S 時播放音樂，可以在連線完成時聽見有源重
低音音箱有一些斷斷續續的聲音。
4. 檢查 LINK LED 燈是否持續亮著藍燈 (連線完成)。
STANDBY
STANDBY
LINK
有源音箱和無線接收器模組之間建立
連線後，LINK LED 指示燈就會停止閃
爍，並持續亮著藍燈。
LINK
藍燈亮起
5. 若 SWA-9000S 未連接，請重複步驟 2 的程序。
TPE - 9
04 連接至您的電視
從有源音箱透過有線或無線連接聆聽電視聲音。
• 若有源音箱連接至所選的 Samsung TV，則可使用電視遙控器控制有源音箱。
– 此功能可用於 2017 和更新的 Samsung Smart TV，這些產品可在有源音箱使用光
纖纜線連接至電視時支援藍牙功能。
– 此功能也可以使用電視功能表調整音場和各種設定，以及音量和靜音。
方法 1。以纜線連接
若廣播中的音訊以杜比數位編碼，而電視上的「數位輸出音訊格式」設定為 PCM，則建議
您將設定變更為杜比數位。變更電視上的設定後，將能體驗更好的聲音品質。(不同的電視
製造商可能會在電視功能表使用不同的字詞來表示 Dolby Digital 和 PCM)
使用 HDMI 纜線連接電視
連接至電視的
HDMI IN (ARC) 連接埠。
HDMI 纜線
HDMI IN
(ARC)
有源音箱底部
HDMI OUT
(TV-ARC)
連接至有源音箱主裝置的
HDMI OUT (TV-ARC) 連接埠。
有源音箱上方
TV ARC
1. 在有源音箱和電視開啟時，連接 HDMI 纜線，如圖所示。
2. 「TV ARC」出現在有源音箱主裝置的顯示視窗上，而有源音箱會播放電視聲音。
• 若聽不到電視聲音，請按下遙控器上或有源音箱上方的
(訊號源) 按鈕以切換至
「D.IN」模式。螢幕會依序顯示「D.IN」和「TV ARC」，並播放電視聲音。
TPE - 10
• 若「TV ARC」沒有出現在有源音箱主裝置的顯示視窗中，請確認 HDMI 纜線是否連
接至正確的連接埠。
• 使用電視遙控器上的音量按鈕變更有源音箱的音量。
附註
• HDMI 是一種介面，可使用單一接頭進行視訊和音訊資料的數位傳輸。
• 若電視提供 ARC 連接埠，請將 HDMI 纜線連接至 HDMI IN (ARC) 連接埠。
• 如果可能，建議您使用空心 HDMI 纜線。若您使用實心 HDMI 纜線，請使用直徑小於
14 公釐的纜線。
• Anynet+ 必須開啟。
• 若 HDMI 纜線不支援 ARC，則此功能無法使用。
使用光纖纜線連接
光纖纜線
(未提供)
有源音箱底部
DIGITAL AUDIO IN
(OPTICAL)
OPTICAL OUT
有源音箱上方
HDMI IN 1
D.IN
HDMI IN 2
1. 使用數位光纖纜線 (未提供) 將有源音箱上的 DIGITAL AUDIO IN (OPTICAL) 插孔連
接至電視上的 OPTICAL OUT 插孔。
2. 按下上方面板或遙控器上的
(訊號源) 按鈕，然後選擇「D.IN」模式。
TPE - 11
Auto Power Link
Auto Power Link 會在開啟電視時自動開啟有源音箱。
1. 使用數位光纖纜線 (未提供) 連接有源音箱與電視。
2. 按下遙控器上的向左按鈕 5 秒鐘，以開啟或關閉 Auto Power Link。
• Auto Power Link 預設設定為 ON。
(若要關閉此功能，請按住遙控器上的向左按鈕 5 秒。)
• 視連接的裝置種類，Auto Power Link 可能無法運作。
• 此功能僅在「D.IN」模式中可使用。
方法 2。無線連線
透過藍牙連線電視
若電視使用藍牙連線，您可以聆聽立體聲音效，且省去連接纜線的麻煩。
• 一次只能連線一台電視。
有源音箱上方
PAIR
或者
ND
SOUODE
M
初始連線
1. 按下遙控器上的
(或者)
PAIR 按鈕以進入「BT PAIRING」模式。
a. 按下上方面板上的
(訊號源) 按鈕，然後選擇「BT」。
若沒有藍牙裝置連接至有源音箱，則「BT」會在幾秒內自動變更為
「BT READY」。
b. 出現「BT READY」時，按住有源音箱上方面板的
(訊號源) 按鈕超過
5 秒，以顯示「BT PAIRING」。
2. 選擇電視上的藍牙模式。 (如需更多資訊，請參見電視手冊。)
3. 從電視畫面上的清單中選擇「[AV] Samsung Soundbar Q80R」。
可用的有源音箱會在電視藍牙裝置清單中以「Need Pairing 」或「Paired」顯示。
若要連線至有源音箱，請選擇訊息並建立連線。
• 若電視已連線，則 [電視名稱] →「BT」會出現在有源音箱前方顯示器上。
4. 您現在可以從有源音箱聆聽電視聲音。
TPE - 12
若裝置無法連線
• 若先前連線的有源音箱清單 (例如「[AV] Samsung Soundbar Q80R」) 出現在清單中，
請刪除。
• 然後重複步驟 1 到 3。
附註
• 首次將有源音箱連線至電視後，請使用「BT READY」模式重新連線。
從電視中斷有源音箱連線
按下上方面板或遙控器上的
(訊號源) 按鈕，然後切換為除了「BT」以外的任何模式。
• 中斷連線需要時間，因為電視必須收到來自有源音箱的回應。(所需時間依電視型號而不
同。)
• 若要取消有源音箱和電視之間的自動藍牙連線，請在有源音箱處於「BT READY」狀態
時，按下遙控器上的 p (播放/暫停) 按鈕 5 秒。(切換開啟 → 關閉)
BT READY 和 BT PAIRING 之間有什麼差異？
• BT READY：在此模式中，您可以搜尋先前連線的電視或將先前連線的行動裝置連線至
有源音箱。
• BT PAIRING : 在此模式中，您可以將新的裝置連線至有源音箱。
(按下遙控器上的 PAIR 按鈕，或按住有源音箱上方的
(訊號源) 按鈕超過 5 秒，
同時有源音箱處於「BT」模式。)
附註
• 連線藍牙裝置時，若要求 PIN 碼，請輸入 <0000>。
• 在藍牙連線模式中，若有源音箱和藍牙裝置之間的距離超過 10 公尺，會遺失藍牙連
線。
• 有源音箱會在就緒狀態持續 18 分鐘後自動關閉。
• 在下列狀況下，有源音箱無法正確執行藍牙搜尋或連線：
– 若有源音箱附近有強烈電場。
– 若有數個藍牙裝置同時與有源音箱配對。
– 若藍牙裝置關閉、位置不正確或故障。
• 電子裝置可能會造成無線電波干擾。產生電磁波的裝置必須遠離有源音箱主裝置 - 例
如微波爐、無線 LAN 裝置等。
TPE - 13
透過 Wi-Fi 連線
連線前的檢查清單
1. 確認您的 Samsung Smart TV 於 2013 年後推出。
此功能僅與 2013 年後推出的 Samsung Smart TV 相容。
2. 確認 無線路由器 (Wi-Fi) 準備就緒並且在運作當中。
3. 確認電視連線至無線路由器 (您的 Wi-Fi 網路)。
有源音箱上方
步驟 1：將有源音箱連線至 Wi-Fi
1. 按下有源音箱上方或遙控器上的
(訊號源) 按鈕，以選擇「WIFI」模式。
• 若使用選定的 Samsung TV (支援藍牙的 2016 ~ 2018 Samsung Smart TV。)
– 若您在電視開啟時選擇「WIFI」模式，電視螢幕會顯示彈出視窗，提供如何自動
將有源音箱連線至無線路由器 (Wi-Fi) 的說明。請參閱電視彈出視窗中的說明。
有源音箱上方
WIFI
2. 將行動裝置 (智慧型手機，平板等) 連線至電視所連線的 Wi-Fi 網路。
TPE - 14
3. 安裝並啟動行動裝置 (智慧型手機，平板等) 上的 SmartThings 應用程式。
Android
iOS
SmartThings 應用程式
4. 按照行動裝置上應用程式畫面中的說明，將有源音箱連線至 Wi-Fi 網路。
步驟 2：設定電視
• 若變更有源音箱的輸入訊號源後，電視中斷無線網路連線，請使用電視功能表重新將電
視連線至網路。
對於 2019 年推出的電視
首頁 (
)  設定 ( )  音效  音效輸出  [AV] Samsung Soundbar Q80R (Wi-Fi)
對於 2018 年推出的電視
首頁 (
)  設定 ( )  音效  音效輸出  [AV] Samsung Soundbar Q80R (Wi-Fi)
對於 2017 年推出的電視
首頁 (
)  設定 ( )  音效  音效輸出  [AV] Samsung Soundbar Q80R (Wi-Fi)
對於 2016 年推出的電視
首頁 (
)  設定 ( )  音效  選擇喇叭  [AV] Samsung Soundbar Q80R (Wi-Fi)
對於 2015 年推出的電視
功能表  音效  揚聲器清單
對於 2014 年推出的電視
功能表  音效  喇叭設定  Multiroom Link - 設定
附註
• 電視和有源音箱必須連線至相同的無線網路 (Wi-Fi)。
• 若您的無線路由器 (Wi-Fi) 使用 DFS 頻道，您將無法建立電視和有源音箱之間的 Wi-Fi
連線。請聯絡您的網際網路服務提供者，瞭解詳細資訊。
• 若 5GHz Wi-Fi 連線狀況不順暢，請使用 2.4GHz 頻寬。
• 由於不同的製造年份會有不同的功能表，請參閱您的電視手冊。
TPE - 15
05 連線外部裝置
透過有線或無線網路連線至外部裝置，可透過有源音箱播放外部裝置的聲音。
使用 HDMI 纜線連接 (能夠使用 Dolby Atmos 解碼和播放)
• 使用 Dolby Atmos® 時：若輸入訊號源為 Dolby Atmos®，則會輸出 5.1.2 頻道。
若 Dolby Atmos® 使用中，則由 SOUND MODE 按鈕控制的有源音箱音效模式無法使
用。
• 重要事項：本產品僅在 HDMI 模式中才能支援 Dolby Atmos®。
有源音箱上方
HDMI 1
或者
DIGITAL AUDIO IN
(OPTICAL)
HDMI 纜線
HDMI IN 1
或者
HDMI OUT
HDMI IN 2
外部裝置
HDMI IN
(ARC)
HDMI 2
HDMI 纜線
HDMI OUT
(TV-ARC)
有源音箱底部
1. 將 HDMI 纜線從有源音箱底部的 HDMI IN 1 或 HDMI IN 2 插孔連接至數位裝置上的
HDMI OUT 插孔。
2. 將 HDMI 纜線從有源音箱底部的 HDMI OUT (TV-ARC) 插孔連接至電視上的 HDMI
IN 插孔。
3. 按下上方面板或遙控器上的
(訊號源) 按鈕，然後選擇「HDMI 1」或「HDMI 2」。
4. 「HDMI 1」或「HDMI 2」模式顯示在有源音箱顯示面板上並播放聲音。
TPE - 16
附註
• 啟用 Dolby Atmos® 時，「DOLBY ATMOS」會顯示在前方顯示器。
在 BD 播放器或其他裝置設定 Dolby Atmos®。
• 開啟 BD 播放器或其他裝置的設定功能表上的音訊輸出選項，並確認針對位元流選擇
「無編碼」。例如，在 Samsung BD 播放器上，前往首頁功能表 → 音效 → 數位輸出，
然後選擇位元流 (尚未處理)。
• 若音訊輸出選項包括次要音訊，請務必將其設定為關閉。
• 確認內容支援 Dolby Atmos®。
使用 HDMI 纜線連接
有源音箱上方
HDMI 1
或者
DIGITAL AUDIO IN
(OPTICAL)
HDMI 纜線
HDMI IN 1
或者
HDMI OUT
HDMI IN 2
外部裝置
HDMI IN
(ARC)
HDMI 2
HDMI 纜線
HDMI OUT
(TV-ARC)
有源音箱底部
1. 將 HDMI 纜線從有源音箱底部的 HDMI IN 1 或 HDMI IN 2 插孔連接至數位裝置上的
HDMI OUT 插孔。
2. 將 HDMI 纜線從有源音箱底部的 HDMI OUT (TV-ARC) 插孔連接至電視上的 HDMI
IN 插孔。
3. 按下上方面板或遙控器上的
(訊號源) 按鈕，然後選擇「HDMI 1」或「HDMI 2」。
4. 「HDMI 1」或「HDMI 2」模式顯示在有源音箱顯示面板上並播放聲音。
TPE - 17
使用光纖纜線連接
有源音箱上方
BD/DVD 播放器/
機上盒/遊戲主控台
D.IN
OPTICAL OUT
DIGITAL AUDIO IN
(OPTICAL)
光纖纜線
(未提供)
有源音箱底部
1. 將主裝置上的 DIGITAL AUDIO IN (OPTICAL) 連接至訊號源上的 OPTICAL OUT 插
孔裝置使用數位光纖纜線 (未提供)。
2. 按下上方面板或遙控器上的
(訊號源) 按鈕，以選擇「D.IN」。
TPE - 18
06 連線行動裝置
透過藍牙連線
若行動裝置使用藍牙連線，您可以聆聽立體聲音效，且省去連接纜線的麻煩。
• 您無法一次連線多個藍牙裝置。
有源音箱上方
PAIR
或者
藍牙裝置
ND
SOUODE
M
初始連線
1. 按下遙控器上的
(或者)
PAIR 按鈕以進入「BT PAIRING」模式。
a. 按下上方面板上的
(訊號源) 按鈕，然後選擇「BT」。
若沒有藍牙裝置連接至有源音箱，則「BT」會在幾秒內自動變更為
「BT READY」。
b. 出現「BT READY」時，按住有源音箱上方面板的
(訊號源) 按鈕超過
5 秒，以顯示「BT PAIRING」。
2. 從清單中選擇「[AV] Samsung Soundbar Q80R」。
• 當有源音箱連線至藍牙裝置時，[藍牙裝置名稱] →「BT」就會出現在前方顯示器。
3. 播放位於透過有源音箱使用藍牙連接之裝置的音樂檔案。
若裝置無法連線
• 若先前連線的有源音箱清單 (例如「[AV] Samsung Soundbar Q80R」) 出現在清單中，
請刪除。
• 然後重複步驟 1 和 2。
附註
• 首次將有源音箱連線至行動裝置後，請使用「BT READY」模式重新連線。
TPE - 19
BT READY 和 BT PAIRING 之間有什麼差異？
• BT READY：在此模式中，您可以搜尋先前連線的電視或將先前連線的行動裝置連線至
有源音箱。
• BT PAIRING : 在此模式中，您可以將新的裝置連線至有源音箱。
(按下遙控器上的 PAIR 按鈕，或按住有源音箱上方的
(訊號源) 按鈕超過 5 秒，
同時有源音箱處於「BT」模式。)
附註
• 連線藍牙裝置時，若要求 PIN 碼，請輸入 <0000>。
• 在藍牙連線模式中，若有源音箱和藍牙裝置之間的距離超過 10 公尺，會遺失藍牙連
線。
• 有源音箱會在就緒狀態持續 18 分鐘後自動關閉。
• 在下列狀況下，有源音箱無法正確執行藍牙搜尋或連線：
– 若有源音箱附近有強烈電場。
– 若有數個藍牙裝置同時與有源音箱配對。
– 若藍牙裝置關閉、位置不正確或故障。
• 電子裝置可能會造成無線電波干擾。產生電磁波的裝置必須遠離有源音箱主裝置 - 例
如微波爐、無線 LAN 裝置等。
• 有源音箱僅支援中等品質 SBC 資料(44.1kHz, 48kHz）
• 只能連接至支援 A2DP（AV）功能的藍牙裝置。
• 不能將有源音箱連接至僅支援 HF（Hands Free）功能的藍牙裝置。
• 配對有源音箱與藍牙裝置後，如果從裝置的已掃描裝置清單中選取
「[AV] Samsung Soundbar Q80R」，則會自動將有源音箱切換至 「BT」模式。
– 僅當有源音箱列出在藍牙裝置的搜尋到的裝置清單中時才可用。（藍牙裝置和有源
音箱先前必須至少已配對 一次。）
• 僅當有源音箱顯示「BT READY」 時，有源音箱才會出現在藍牙裝置的搜尋到的裝置清
單中。
• 若有源音箱已處於藍牙模式且已配對至藍牙裝置，就無法配對至另一個藍牙裝置。
TPE - 20
從有源音箱中斷藍牙裝置的連線
您可以從有源音箱斷開藍牙裝置的連線。如需說明，請參閱藍牙裝置的使用者手冊。
• 有源音箱將斷開連線。
• 當有源音箱從藍牙裝置中斷連線時，有源音箱就會在前方顯示器上顯示
「BT DISCONNECTED」。
從藍牙裝置中斷有源音箱連線
按下上方面板或遙控器上的
(訊號源) 按鈕，然後變更為「BT」以外的任何模式。
• 中斷連線需要時間，因為藍牙裝置必須收到來自有源音箱的回應。(不同的藍牙裝置需
要不同的中斷連線時間)
• 當有源音箱從藍牙裝置中斷連線時，有源音箱就會在前方顯示器上顯示
「BT DISCONNECTED」。
附註
• 在藍牙連線模式中，如果有源音箱與藍牙裝置之間的距離超過 10 公尺，藍牙連線將會
中斷。
• 保持「備妥」狀態 18 分鐘後，有源音箱將會自動關閉。
藍牙相關詳細資訊
藍牙技術可讓符合藍牙的裝置使用無線連線輕鬆互連。
• 在下列情況下，藍牙裝置可能導致噪音或發生故障，具體視使用情況而定：
– 您身體的某個部位接觸藍牙裝置或有源音箱的接收/傳送系統。
– 受來自牆壁、角落或辦公室分隔物形成之障礙的電子變體影響。
– 受相同頻段裝置（包括醫裝置、微波爐和無線 LAN）的電子干擾。
• 當有源音箱與藍牙裝置靠得很近時使兩者配對。
• 有源音箱與藍牙裝置之間的距離越遠，品質就越差。
如果距離超出藍牙工作範圍，連線將會中斷。
• 在接收敏感度較差的區域中，藍牙連線可能無法正常工作。
• 藍牙連線只能在靠近裝置時才能正常工作。如果藍牙裝置超出範圍，則會自動切斷連
線。即使在範圍內，牆壁或門等障礙物也可能導致聲音品質下降。
• 這個無線裝置可能會在其操作期間造成電子干擾。
TPE - 21
透過 Wi-Fi (無線網路) 連線
• 將單一有源音箱連線至 Wi-Fi，以存取各種音樂串流服務和網際網路電台。將多個有源
音箱連線至 Wi-Fi，以使用群組播放或立體聲模式
• 若要透過無線網路 (Wi-Fi) 將有源音箱連線至行動裝置，則需要 SmartThings 應用程
式。
有源音箱上方
行動裝置
初始連線
1. 按下有源音箱上方或遙控器上的
(訊號源) 按鈕，以選擇「WIFI」模式。
有源音箱上方
WIFI
2. 安裝並啟動行動裝置 (例如智慧型手機或平板) 上的 SmartThings 應用程式。
Android
iOS
TPE - 22
SmartThings 應用程式
3. 啟動應用程式，然後按照畫面上的指示在應用程式中註冊 (新增) 有源音箱。
• 自動快顯視窗 (以下第三張圖) 在某些行動裝置上可能無法使用。
在此情況下，請從應用程式功能表選擇並完成「Add device」。有源音箱現在已新增
至應用程式。
啟動應用程式
自動快顯視窗
新增揚聲器
附註
• 若要連接其他 SWA-9000S 無線後側揚聲器套件 (未提供)，請從有源音箱中斷連接
Samsung 無線揚聲器以停用環場音效系統。(若您在連接環場揚聲器時沒有中斷連接
SWA-9000S 揚聲器，則會透過 Samsung 無線揚聲器和環場揚聲器來播放聲音。)
TPE - 23
07 連接 AMAZON 產品
• 某些國家/地區可能無法使用此功能。
• 本服務由 Amazon 提供，可隨時終止。Samsung 對於服務可用性不具任何責任。
• Amazon Alexa 應用程式畫面可隨時變更，不必事先通知。
連接並搭配 Amazon 產品 (Amazon Echo) 使用
使用 Amazon Echo 產品控制有源音箱並享受由 Amazon Echo 提供的音樂服務。
附註
• 檢查有源音箱是否連線至 Wi-Fi。(請參閱「透過 Wi-Fi (無線網路) 連線」)
1. 在 SmartThings 應用程式中，將有源音箱的名稱變更為 Amazon 裝置可辨識的名稱。
(範例：Samsung、有源音箱、客廳、家庭活動室、臥室、辦公室等。)
注意
• Amazon 裝置無法辨識包含特殊字元等元素的名稱。
選擇 Edit
選擇揚聲器
TPE - 24
變更名稱
儲存
2. 在 Alexa 應用程式中，於 Skills 中搜尋「Samsung Wireless Audio」，然後選擇
「ENABLE」。
• 若您已經有 Skills 設定，請略過此步驟。
Amazon Alexa
應用程式
選擇 Skills
搜尋
TPE - 25
啟用
使用語音命令控制有源音箱
• 可搭配有源音箱使用的 Amazon Echo 服務僅限於音樂。其他由 Amazon Echo 提供
的服務，例如新聞和天氣，只能透過 Amazon Echo 產品存取。
觸發 + 命令 + 揚聲器名稱
使用您在 SmartThings 應用程式中變更的揚聲器名稱。(請參閱「連接並搭配
Amazon 產品 (Amazon Echo) 使用」)
動作
語音命令
搜尋已新增至與 Amazon Alexa 帳戶連
接的 SmartThings 帳戶的音訊裝置
「Alexa 探索裝置」
* 若要對命名為「客廳」的有源音箱使用語音命令
動作
將音量設定為 5
增加音量
靜音聲音
聆聽名稱為 KISS FM 的廣播電台
播放下一首歌曲
停止音訊
開啟音訊
關閉音訊
變更輸入訊號源
語音命令
「Alexa 在客廳將音量設定為 5」
「Alexa 在客廳增加音量」
「Alexa 在客廳靜音」
「Alexa 在客廳播放 Kiss FM」
「Alexa 在客廳播放下一首歌曲」
「Alexa 在客廳停止」
「Alexa 在客廳開啟」
「Alexa 在客廳關閉」
「Alexa 在客廳切換為藍牙」
TPE - 26
08 使用遙控器
如何使用遙控器
開啟及關閉有源音箱。
電源
PAIR
按下可選擇連接至有源音箱的訊號源。
訊號源
按下
(靜音) 按鈕以靜音聲音。
PAIR
再次按下以取消靜音聲音。
SOUND
MODE
VOL
WOOFER
SOUND
MODE
您可以選擇
SOUND
MODE
SOUND
MODE
PAIR
靜音
PAIR
STANDARD、SURROUND、
GAME PRO 或 ADAPTIVE SOUND，以
選擇所需的聲音模式。
若您要享受原始聲音，請選擇
「STANDARD」模式。
• GAME
PAIR PRO 模式
使用特別為遊戲最佳化聲音的專用設
WOOFER
VOL
SOUNDBAR
SOUND
MODEVOL
定，讓自己沉浸在場景中。
WOOFER
SOUND
MODE
•
ADAPTIVE SOUND 模式
自動分析內容並提供最佳化的聲音，以
及自動提升低音量的語音清晰度。
PAIR
VOL
VOL
Bluetooth
VOL
PAIR
WOOFER
SOUND
MODE
WOOFER
TPE - 27
按下 PAIR 按鈕。「BT PAIRING」會顯
示在有源音箱的顯示器中。
在此模式中，您可以從藍牙裝置的搜尋清
WOOFER
單中選擇有源音箱，以將有源音箱連線至
新的藍牙裝置。
按下 p 按鈕可暫停音樂檔案。
若您再次按下此按鈕，就會播放音樂檔案。
播放/暫停
(BT/Wi-Fi)
PAIR
按下指示區域選擇向上/向下/向左/向右。
SOUND
MODE
向上/向下/
向左/向右
PAIR
SOUND
MODE
按下按鈕上的向上/向下/向左/向右選擇或設定功能。
• 音樂略過
按向右按鈕可選擇下一個音樂檔案。按向左按鈕可選擇上一個音樂檔案。
VOL
VOL
WOOFER
WOOFER
• Anynet+ / Auto Power Link
您可以開啟或關閉 Anynet+ 和 Auto Power Link。
Anynet+ 和 Auto Power Link 分別由向右和向左按鈕來開啟和關閉。
– Anynet+ : 若有源音箱透過 HDMI 纜線連接至 Samsung TV，您可以使
用 Samsung TV 遙控器控制有源音箱。按住向右按鈕 5 秒，以切換
Anynet+ ON 和 OFF。
– Auto Power Link : 若有源音箱透過數位光纖纜線連接至電視，則有源
音箱可在打開電視時自動開啟。按住向左按鈕 5 秒鐘，將 Auto Power
Link 切換為 ON 或 OFF。
– Anynet+ / Auto Power Link 預設設定為 ON。
• ID SET
按住向上按鈕 5 秒，以完成 ID SET (連接至周邊配件項目時)。
TPE - 28
您可以選擇 TREBLE、BASS、SYNC、CENTER LEVEL、SIDE
LEVEL、FRONT TOP LEVEL、REAR LEVEL、VIRTUAL ON/OFF。
– 若要控制高音或低音的音量，請選擇聲音設定中的 TREBLE 或 BASS，然
後使用向上/向下按鈕介於 -6~+6 之間調整音量。
– 按住
(音效控制) 按鈕大約 5 秒，以調整每個頻帶的聲音。可使用向左/
向右按鈕選擇 150Hz、300Hz、600Hz、1.2kHz、2.5kHz、5kHz 和 10kHz，
每項都能使用向上/向下按鈕調整為介於 -6 到 +6 之間的設定。
– 若要控制高音或低音的音量，請選擇聲音設定中的 CENTER
LEVEL、SIDE LEVEL 或 FRONT TOP LEVEL，然後使用向上/向下按鈕
介於 -6~+6 之間調整音量。
– 如果電視上的視訊與有源音箱的音訊不同步，請在聲音控制中選擇
SYNC，然後使用向上/向下按鈕在 0~300 毫秒之間設定音訊延遲。
– 若連接了環場音效揚聲器，請選擇 REAR LEVEL，然後使用向上/向下按
鈕在 -6 到 +6 的範圍內調整音量。VIRTUAL 揚聲器功能可使用向上/向下
按鈕開啟或進行
ON/OFF。
PAIR
– 僅某些功能支援 SYNC。
音效控制
PAIR
SOUND
MODE
• 初始化
SOUND
MODE 在有源音箱關閉的情況下，按住
(音效控制) 按鈕 5 秒，直到揚聲器開啟
為止。「INIT」會出現在顯示器上，而有源音箱則會初始化。
PAIR
SO
M UN
OD D
E
R
W
OO
N
U
SO
WOOFER
D
BA
R
BA
R
N
U
SO
VO
L
D
BA
R
D
SO
U
N
VO
L
D
N
U
O
VOL
FE
FE
W
OO
W
OO
FE
FE
OO
BA
R
SOUND
MODE
VO
L
WOOFER
R
SO
M UN
OD D
E
WOOFER
R
R
VOL
SO
M UN
OD D
E
向上或向下移動按鈕，以將有源重低音音箱的音量調整為 -12 或介於 -6 到 +6
之間。若要將有源重低音音箱音量設定為 0，請按下按鈕。
向上或向下推動按鈕可調整音量。
• 靜音
按下 VOL 按鈕以靜音。再次按下可取消靜音。
TPE - 29
W
OO
F
BA
R
D
N
U
SO
VO
L
D
N
SO
U
U
VO
L
N
D
BA
R
BA
R
W
OO
F
W
OO
F
ER
ER
SO
M UN
OD D
E
SO
M UN
OD D
E
SO
M UN
OD D
E
ER
WOOFER
SO
VOL
VO
L
VOL
SO
M UN
OD D
E
5 Sec
1. 關閉有源音箱。
BYE
2. 若您不想要使用此功能，請重複向上推
動並按住 WOOFER 按鈕 5 秒，直到
「OFF-TV REMOTE」出現在顯示器中。
U
N
D
BA
R
OFF-TV REMOTE
SO
VO
L
W
OO
FE
R
SO
M UN
OD D
E
5 Sec
3. 若您想要使用電視遙控器控制有源音
箱，請重複向上推動並按住 WOOFER
按鈕 5 秒，直到「ALL-TV REMOTE」出
現在顯示器中。然後，使用電視功能表
選擇外部揚聲器。
ALL-TV REMOTE
D
N
SO
U
VO
L
BA
R
W
OO
FE
R
SO
M UN
OD D
E
5 Sec
TPE - 30
R
FE
W
OO
BA
R
D
N
VO
L
U
首先使用電視功能表，將 Samsung TV 的
電視音訊設定為外部揚聲器，然後使用
Samsung 遙控器控制有源音箱的音量。如
需更多資訊，請參閱電視的使用者手冊。此
功能的預設模式由 Samsung TV 遙控器控
制。若您的電視不是 Samsung TV，請按照
以下指示變更此功能的設定。
(預設模式)
SAMSUNG-TV REMOTE
SO
若您有 Samsung TV，可以使用
Samsung TV 隨附的 IR (紅外線) 遙控
器調整有源音箱的音量。
4. 若您想要將有源音箱恢復為預設模式
(由 Samsung TV 遙控器控制)，請重複
向上推動並按住 WOOFER 按鈕 5 秒，
直到「SAMSUNG-TV REMOTE」出現
在顯示器中。
SO
M UN
OD D
E
透過電視遙控器調整有源音
箱音量
– 每次按住 WOOFER 按鈕 5 秒時，
就會以下列順序切換模式：
「SAMSUNG-TV REMOTE」 (預設
模式) →「OFF-TV REMOTE」→
「ALL-TV REMOTE」。
– 某些遙控器可能不提供使用此功
能。
– 支援此功能的製造商：VIZIO，LG，
Sony，Sharp，PHILIPS，
PANASONIC，TOSHIBA，
GRUNDIG，Hisense，RCA
使用隱藏按鈕 (具有多種功能的按鈕)
隱藏按鈕
參考頁面
遙控器按鈕
功能
WOOFER
電視遙控器 開啟/關閉 (待命)
第 30 頁
Anynet+ ON/OFF
第 28 頁
Auto Power Link ON/OFF
向左
向右
第 28 頁
ID SET
向上
第 28 頁
7 環帶 EQ
(音效控制)
第 29 頁
初始化 (待命)
第 29 頁
適用於不同音效模式的輸出規格
輸出
效果
輸入
2.0 頻道
STANDARD
7.1.4 頻道
5.1.2 頻道
7.1.2 頻道
5.1 頻道
5.1.2 頻道
7.1.2 頻道
7.1 頻道
7.1 頻道
5.1 頻道
7.1 頻道
7.1.4 頻道
2.0 頻道
SOUND
2.1 頻道
5.1 頻道 / 7.1 頻道 (DTS)
2.0 頻道
ADAPTIVE
2.1 頻道
5.1 頻道
7.1.4 頻道
GAME PRO
使用有源重低音音箱與無線
後置揚聲器套件
5.1 頻道
2.0 頻道
SURROUND
僅使用有源重低音音箱
5.1 頻道
7.1 頻道
7.1.4 頻道
5.1 頻道
5.1.2 頻道
5.1.2 頻道
5.1.2 頻道
5.1.2 頻道
5.1.2 頻道
5.1.2 頻道
5.1.2 頻道
5.1.2 頻道
5.1.2 頻道
5.1.2 頻道
5.1.2 頻道
7.1 頻道
7.1.2 頻道
7.1.2 頻道
7.1.2 頻道
7.1.2 頻道
7.1.2 頻道
7.1.2 頻道
7.1.2 頻道
7.1.2 頻道
7.1.2 頻道
7.1.2 頻道
7.1.2 頻道
• 若輸入訊號源為 Dolby Atmos®，則會輸出 5.1.2 頻道。由 SOUND MODE 按鈕控制並
列於上方的音效模式無法使用。
• Samsung 無線後置揚聲器套件可另外購買。若要購買套件，請聯絡您購買有源音箱時
的廠商。
TPE - 31
09 安裝掛牆托架
牆面安裝元件
安裝注意事項
牆面安裝導桿
• 僅安裝於垂直牆面。
• 請勿安裝於高溫或高濕度的地方。
• 檢查牆壁是否夠堅固，能夠支撐產品重
量。若無法支撐，請強化牆壁或選擇其他
安裝點。
• 購買並使用適合用於該牆壁種類 (灰漿
板、鐵板、木材等) 的銼屑螺絲或固定
器。若可能，請支撐螺絲固定在牆壁螺栓
中。
• 根據您要安裝有源音箱的牆壁類型和厚
度，購買牆面安裝螺絲。
– 直徑：M5
– 長度：建議使用 35 毫米以上。
• 請先將纜線從裝置連接至外部裝置，再
將有源音箱安裝到牆上。
• 在安裝前，請先確認裝置已關閉且拔掉
插頭。否則，可能會造成觸電。
x2
x2
(M4 x L10)
支撐螺絲
螺絲
x2
掛牆托架
1. 對著牆面放置牆面安裝導桿。
• 牆面安裝導桿必須水平。
• 若電視安裝於牆面，請將有源音箱安
裝在距離電視下方至少 5 公分處。
5 公分以上
TPE - 32
2. 將牆面安裝導桿的中線與電視的中央對
齊 (如果您將有源音箱安裝在電視下方)
，然後使用膠帶將牆面安裝導桿固定在
牆上。
• 如果您未在電視下方安裝，請將中線
放在安裝區域的中央。
5. 將螺釘 (未提供) 推入每個支撐螺絲，然
後將每個螺釘緊緊地鎖入支撐螺孔中。
6. 使用 2 個螺絲，以正確的方向在有源音
箱底部安裝 2 個掛牆托架。
中線
3. 將筆尖或銳利的鉛筆筆尖穿過導桿每
端的 A-TYPE 影像中央，以標示支撐螺
絲的孔，然後移除牆面安裝導桿。
4. 使用適當大小的鑽頭，在牆上的每個標
記鑽孔。
• 如果標記與掛釘的位置不一致，請務
必將適當的膨脹管先插入孔中，再插
入支撐螺絲。如果您使用膨脹管，請
確定您鑽的孔足以容納要使用的膨
脹管。
• 組裝時，請確認掛牆托架的吊掛部位
位於有源音箱後側的後方。
有源音箱的後側
有源音箱的右側
TPE - 33
7. 使用已固定的掛牆托架安裝有源音箱，
只要將掛牆托架掛在牆上的支撐螺絲
即可。
10 將有源音箱安裝
在電視架上
元件
x4
8. 如下所示，向下滑動有源音箱，讓掛牆
托架牢固置於支撐螺絲。
• 將支撐螺絲插入掛牆托架寬的部分
(底部)，然後向下滑動掛牆托架，讓
掛牆托架牢固置於支撐螺絲。
橡膠墊
您可以將有源音箱安裝在高度低於 7.6 公分
的電視架上。若要安裝，請先將橡膠墊裝在
有源音箱的底部，再置於電視架上。務必裝
上橡膠墊，才能超出電視架的外緣。請參閱
下圖。
橡膠墊
TPE - 34
11 軟體更新
若有源音箱連線至網際網路，會在關閉有源
音箱時自動進行軟體更新。
• 若要使用自動更新功能，有源音箱必須
連線至網際網路。若拔除有源音箱的電
源線或切斷電源，將會終止對於有源音
箱的 Wi-Fi 連線。若切斷電源，則當恢復
電源或重新連接電源線時，請開啟有源
音箱，然後重新連線至網際網路。
TPE - 35
12 疑難排解
尋求協助之前，請先檢查下列項目。
有源重低音音箱上的紅色 LED 閃爍，且有源
裝置不會開啟。
重低音音箱沒有產生聲音。
電線是否插入插座中？
; 將電源插頭連接至插座中。
若有源重低音音箱沒有連接至有源音箱
主裝置，就會發生此問題。
; 嘗試重新連接有源重低音音箱。
(請參閱第 6 頁。)
某項功能沒有在按下按鈕時運作
空氣中是否有靜電？
; 斷開電源插頭並再次連接。
有源重低音音箱發出嗡嗡聲且明顯震動。
在藍牙模式中發生聲音中斷的情形。
嘗試調整有源重低音音箱的震動情況。
; 向上或向下推動遙控器上的
WOOFER 按鈕，以調整有源重低音音
箱音量。(至 -12，或介於 -6 ~ +6)。
; 請參見第 12 頁和第 19 頁的藍
牙連線章節。
沒有產生聲音。
是否開啟靜音功能？
; 按下
(靜音) 按鈕以取消靜音功能。
音量是否設定為最小？
; 調整音量。
遙控器無法運作。
電量是否已耗盡？
; 更換新電池。
遙控器和有源音箱主裝置之間的距離是
否太遠？
; 將遙控器靠近有源音箱主裝置。
無法連線至電視。
若透過有線網路連線
; 檢查纜線是否正確連接。
– 檢查連接埠名稱，確認纜線連接
至正確的連接埠。如需說明，請參
閱解釋每個連接方法的頁面。
; 按下有源音箱上方面板或遙控器上的
(訊號源) 按鈕，以檢查模式是否正
確。
若透過無線網路連線
; 透過藍牙連線
1. 將有源音箱切換至「BT PAIRING」
模式，然後使用電視重新搜尋。
(請參閱第 12 頁的詳細資訊)
TPE - 36
; 透過 Wi-Fi 連線
1. 檢查電視是否為相容型號。
• 僅支援 2013 年後推出的
Samsung Smart TV。
2. 檢查電視是否連線至 Wi-Fi。
• 若電視沒有連線至 Wi-Fi，請使用
電視上的網路功能表建立連線。
(請參閱電視使用者手冊)
3. 檢查有源音箱是否連線至 Wi-Fi。
• 連接有源音箱時，您可以在執行
SmartThings 應用程式時在行動
裝置的揚聲器清單中找到有源音
箱。請參閱第 22 頁的詳細資
訊。
4. 檢查 DFS 頻道。
• 若您的無線路由器 (Wi-Fi) 使用
DFS 頻道，則您無法建立電視和
有源音箱之間的 Wi-Fi 連線。請聯
絡您的網際網路服務提供者，瞭解
詳細資訊。
13 授權
Manufactured under license from Dolby
Laboratories. Dolby, Dolby Atmos, Dolby
Audio, Dolby Digital Plus, Pro Logic, and
the double-D symbol are trademarks of
Dolby Laboratories.
For DTS patents, see http://patents.dts.com.
Manufactured under license from DTS
Licensing Limited. DTS, the Symbol, & DTS
and the Symbol together, DTS:X, and the
DTS:X logo are registered trademarks and/
or trademarks of DTS, Inc. in the United
States and/or other countries. © DTS, Inc.
All Rights Reserved.
The terms HDMI and HDMI HighDefinition Multimedia Interface, and the
HDMI Logo are trademarks or registered
trademarks of HDMI Licensing LLC in
the United States and other countries.
• Spotify 軟體受協力廠商授權約束，詳
情請見：
www.spotify.com/connect/thirdparty-licenses。
• 如需 Spotify Connect 的相關資訊，請
造訪 www.spotify.com/connect
TPE - 37
14 開放式原始碼授
權聲明
如需本產品中所用開放式原始碼的更多資
訊，請造訪下列網站：
http://opensource.samsung.com
15 關於維修的重要
說明
本使用說明書中的圖片和圖解僅供參考，可
能與實際的產品外觀有所不同。
TPE - 38
16 規格和指南
規格
HW-Q80R
型號名稱
8.8 千克
重量
尺寸 (寬 x 高 x 厚）
1226.0 x 83.0 x 136.0 毫米
+5°C 到 +35°C
工作溫度範圍
工作濕度範圍
10 % 到 75 %
放大器
額定輸出功率
18W x 10 + 10W x 3、4 歐姆
支援的播放格式
LPCM 8ch、Dolby Digital、
Dolby Atmos (True HD / Digital Plus)、DTS:X
PS-WR75B
有源重低音音箱名稱
9.8 千克
重量
尺寸 (寬 x 高 x 厚）
205.0 x 403.0 x 403.0 毫米
放大器
額定輸出功率
160W
附註
• Samsung Electronics Co., Ltd 保留隨時變更規格的權利，恕不另行通知。
• 重量和尺寸為估計值。
• 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅
自變更頻率、加大功率或變更原設計之特性及功能。第十四條 低功率射頻電機之使用不
得影響飛航安全及干擾合法通信；經發現有干擾現象時，應改善至無干擾時方得繼續使
用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通
信或工業、科學及醫療用電波輻射性電機設備之干擾。
• HW-Q80R: AC110-240V~50/60Hz、35W
• PS-WR75B: AC110-240V~50/60Hz、28W
注意事項：若您開啟/關閉 Wi-Fi，有源音箱將會自動重新啟動。
Wi-Fi 連接埠停用方式
藍牙連接埠停用方式
按下有源音箱下方面板的 ID SET 按鈕 30 秒，以
開啟 / 關閉 Wi-Fi。
按下有源音箱下方面板的 NETWORK 按鈕
30 秒，以開啟 / 關閉藍牙。
TPE - 39
RoHS
設備名稱：有源音箱
Equipment name
型號（型式）：HW-Q80R
Type designation (Type)
限用物質及其化學符號
Restricted substances and its chemical symbols
單元
Ｕnit
鉛
Lead
(Pb)
六價鉻
多溴聯苯
多溴二苯醚
汞
鎘
Hexavalent Polybrominated Polybrominated
Mercury Cadmium
chromium
biphenyls
diphenyl ethers
(Hg)
(Cd)
(Cr+6)
(PBB)
(PBDE)
電路板
－
○
○
○
○
○
外殼
－
○
○
○
○
○
金屬零件
－
○
○
○
○
○
揚聲器
○
○
○
○
○
○
配件 (例：線材,
遙控器)
－
○
○
○
○
○
備考1.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 1：“○” indicates that the percentage content of the restricted substance does not exceed the
percentage of reference value of presence.
備考2.〝－〞係指該項限用物質為排除項目。
Note 2：The “－” indicates that the restricted substance corresponds to the exemption.
設備名稱：有源重低音音箱
Equipment name
單元
Ｕnit
型號（型式）：PS-WR75B
Type designation (Type)
限用物質及其化學符號
Restricted substances and its chemical symbols
鉛
Lead
(Pb)
六價鉻
多溴聯苯
多溴二苯醚
汞
鎘
Hexavalent Polybrominated Polybrominated
Mercury Cadmium
chromium
biphenyls
diphenyl ethers
(Hg)
(Cd)
(Cr+6)
(PBB)
(PBDE)
電路板
－
○
○
○
○
○
外殼
－
○
○
○
○
○
金屬零件
－
○
○
○
○
○
揚聲器
○
○
○
○
○
○
配件 (例：線材,
遙控器)
－
○
○
○
○
○
備考1.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 1：“○” indicates that the percentage content of the restricted substance does not exceed the
percentage of reference value of presence.
備考2.〝－〞係指該項限用物質為排除項目。
Note 2：The “－” indicates that the restricted substance corresponds to the exemption.
© 2019 Samsung Electronics Co., Ltd. All rights reserved.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care Centre.
Area
Contact Centre 
Web Site
` Asia Pacific
CHINA
400-810-5858
www.samsung.com/cn/support
TAIWAN
0800-329-999
0809-00-5237 ( B2B / Dealer)
www.samsung.com/tw/support
HONG KONG
3698 4698
MACAU
0800 333
www.samsung.com/hk/support (Chinese)
www.samsung.com/hk_en/support (English)
SINGAPORE
1800 7267864 | 1800-SAMSUNG
www.samsung.com/sg/support
AUSTRALIA
1300 362 603
www.samsung.com/au/support
NEW ZEALAND
0800 726 786
www.samsung.com/nz/support
VIETNAM
1800 588 889
www.samsung.com/vn/support
THAILAND
0-2689-3232
1800-29-3232 (Toll free)
www.samsung.com/th/support
MYANMAR
+95-1-2399-888
www.samsung.com/mm/support
CAMBODIA
+855-23-993232
1800-20-3232 (Toll free)
www.samsung.com/th/support
LAOS
+856-214-17333
MALAYSIA
1800-88-9999
+603-7713 7420 (Overseas contact)
www.samsung.com/my/support
INDONESIA
021-5699-7777
0800-112-8888 (Toll Free)
www.samsung.com/id/support
PHILIPPINES
1-800-10-726-7864 [ PLDT Toll Free ]
1-800-8-726-7864 [ Globe Landline and Mobile ]
02-422-2111 [ Standard Landline ]
www.samsung.com/ph/support
INDIA
1800 40 SAMSUNG (1800 40 7267864) (Toll-Free)
NEPAL
16600172667 (Toll Free for NTC Only)
9801572667
BANGLADESH
09612300300
08000300300 (Toll free)
SRI LANKA
+9411SAMSUNG (+94117267864)
www.samsung.com/in/support