Euro Appliances EMJBQ30SX User Manual

Euro Appliances EMJBQ30SX User Manual
EMJBQ30SX
COD. 04047MS - 26.05.2016 REV1
WARNING: The appliance and its accessible parts become hot
during use.
Care should be taken to avoid touching heating elements.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with
the appliance
Cleaning and user maintenance shall not be made by children without
supervision.
WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire. NEVER try to extinguish a fire with
water, but switch off the appliance and then cover flame e.g. with a lid
or a fire blanket.
WARNING: Danger of fire: do not store items on the cooking
surfaces.
WARNING: If the surface is cracked, switch of the appliance to
avoid the possibility of electric shock.
DO NOT use a steam cleaner to clean this appliance..
This appliance is not intended to be operated by means of an
external timer or separate remote-control system.
WARNING: Use only hob guards designed by the manufacturer of
the cooking appliance or indicated by the manufacturer of the
appliance in the instructions for use as suitable or hob guards
incorporated in the appliance. The use of inappropriate guards
can cause accidents.
WARNING:The cooking process has to be supervised. A short
term cooking process has to be supervised continuously.
2
INSTRUCTIONS AND SUGGESTIONS FOR
USE, INSTALLATION AND MAINTENANCE
OF THE BUILT-IN ELECTRIC BARBECUE
Dear Customer,
thank you for purchasing one of our products. We are confident that this practical and modern
appliance, made with top quality materials, will satisfy your needs in every way. This new piece of
equipment is simple to use but, before operating it, please read this booklet carefully for best
results.
The manufacturer cannot be held liable for consequential damages to objects or persons
resulting from faulty installation or misuse of this appliance.
The manufacturer cannot be held responsible for any inaccuracies due to printing or reproduction errors
contained in the present booklet. The features of the picture diagrams included are purely indicative. We
reserve the right to make any changes to our products that are deemed necessary or useful and in the
interest of the user that are not detrimental to essential operating and safety features.
This cook top was designed to be used exclusively as a cooking appliance: any other use (such as
heating rooms) is to be considered improper and dangerous.
BARBECUE DESCRIPTION
1 Grill
2400 W
2 Grill rack
3 Grill control knob
4 Grill on/off indicator lamp
Caution: this appliance is designed for personal household use only.
Warning: during operation the work surfaces
of the cooking area become very hot: keep
children away!
4
USE
For better results it is recommended you pre-heat the
lava stone for at least 10 minutes on position 1. This
step is strongly recommended when the appliance is
switched on for the first time. It reduces the risk of the
cooked food absorbing the odours produced by the
resistance the first time it is switched on.
1) SWITCHING ON THE BARBECUE
The barbecue is controlled by a power regulator with
12 positions (see fig. 1). Turn the knob clockwise to
the desired position (from 1 to 12) to switch it on.
To use the grill function turn the knob to position 12. A
light click warns that the thermostat has been shut
down and the resistance will quickly become red-hot.
A red indicator lamp indicates it is switched on.
The barbecue allows fast cooking on the grill.
The function of the lava stone contained in the drip
pan is to absorb drippings of oil or fat that are
produced during cooking. It also accumulates heat
during the initial operating phase of the resistance
allowing, before long, uniform grilling very similar to
that obtained using charcoal.
"Warning: Charcoal or similar combustible
fuels must not be used with this appliance”
This cook top was designed to be used exclusively as a cooking
appliance: any other use (such as heating rooms) is to be
considered improper and dangerous.
FIG. 1
5
USE
WARNINGS AND ADVICE FOR THE USER:
when turning the grill on for the first time or if
the grill has remained inactive for a long time,
care must be taken to dry it out by switching
on the grill for 30 minutes to position 1 on the
regulator in order to eliminate any moisture
absorbed by the insulating material.
To use correctly remember:
●Turn the current on only after placing the pan
or food on the grill.
●Never leave the appliance unattended while
using the grill, and keep children at a safe
distance. In particular, ensure that the
handles are in the correct position inwards
and watch out when cooking food with oil
and fat as they are easily inflammable.
●Even after use, the grill remains hot for a long
time. Do not touch it with your hands or other
objects to avoid burns.
●As soon as a crack is noticed on the surface
of the heating element, immediately
disconnect the appliance from the mains.
●The appliance must not be operated with an
external timer or a separate remote-control
system.
●Do not attempt to change the technical
characteristics of the product because it can
be dangerous.
●If you should not to use this appliance any
more (or replace an old model), before
disposing of it, make it inoperative in
conformity with current law on the protection
of health and the prevention of environmental
pollution by making its dangerous parts
harmless, especially for children who might
play on an abandoned appliance.
CAUTION:
In case of hotplate glass breakage:
●shut immediately off all burners and any electrical
heating element and isolate the appliance from
the power supply;
●do not touch the appliance surface;
●do not use the appliance.
6
CLEANING
CAUTION: before cleaning of any kind,
disconnect the appliance from the mains.
Depending on the degree of dirt, we recommend:
- for light stains, a damp sponge is sufficient.
- Encrusted dirt is easily eliminated using a
scraper. Use it with care because it can cause
injury.
- Do not use jets of steam to clean the
appliance.
2) COOKING SURFACE
To maintain the surface of the barbecue always
clean and to extend the lifespan of the appliance, it
is very important to wash it after every use with
warm, soapy water, rinse, and dry thoroughly.
Let the barbecue and all its parts cool off before
cleaning. Do not use scouring pads, abrasive
cleaners or corrosive sprays.
Never allow vinegar, coffee, milk, salt water, lemon
or tomato juice to remain in contact with the
surfaces for long periods of time.
WARNING:
- to maintain the grill in good condition after
use, it should be treated with the special
products available on the market so that the
surface always remains clean. This
procedure is necessary to prevent the
formation of rust.
- Don’t use steam jets for the equipment
cleaning.
- When cleaning the grill, do not raise the
heating element beyond the first block.
7
INSTALLATION
Packaging (cardboard, bags, expanded
polystyrene, nails...) must not be left within
children's reach as they are potential sources
of danger.
An opening in the table top of the piece of modular
furniture must be made with the dimensions
indicated in fig. 2, making sure that the dimensions
of the space required to install the appliance are
observed (see fig. 3).
This is a Class 3 appliance and is therefore
subject to all the requirements set by the
standards for these appliances.
TECHNICAL DATA FOR
INSTALLERS
Installation and maintenance listed in this
section must only be carried out by qualified
personnel (law 46 and D.P.R. 447).
The appliance must be correctly installed in
conformity with current law and the
manufacturer's instructions.
A faulty installation can cause damage to
persons, animals or objects, towards whom the
manufacturer cannot be held responsible.
The cut-off or automatic control devices of the
appliance can only be modified by the
manufacturer or by a duly authorized supplier.
3) INSTALLING THE BARBECUE
Take the barbecue out of its packaging, unpack
the various loose parts, then make sure it is not
damaged. In case of doubt do not use the
appliance and contact a qualified technician.
CAUTION:
do not place the glass directly on the unit.
The bottom of the hob must rest on
the unit.
USEFUL MEASUREMENTS (mm)
BARBECUE
A
B
C
D
E
282
482
59
59
100 min.
FIG. 2
FIG. 3
8
INSTALLATION
4) SECURING THE BARBECUE
- Make sure the gasket adheres to the countertop
evenly all around, press it down with your
fingers, then remove the protective strip of the
gasket and position the barbecue in the opening
made in the worktop.
- Secure the appliance by tightening the clamp
screws "F" (see fig. 5).
- In order to prevent any accidental contact with
the surface of the heated barbecue during use, a
separation in wood must be inserted and
fastened with screws at a minimum distance of
60 mm from the top (fig. 6).
To secure the barbecue to the worktop the fastening
clamps accompanying this booklet must be
assembled. The following procedures must be
carried out to do this:
remove all movable parts from the barbecue;
turn the appliance over taking care to place it on
a soft surface to avoid damaging the external
surfaces;
remove the clamps "G" from the package and
install them according to the diagram in fig. 4.
After these steps have been carried out, the special
gasket that prevents liquids from leaking can be
installed. To fit this gasket correctly, please strictly
follow the directions below:
- detach the gasket strips from their support taking
care that the transparent protection remains
attached to the gasket.
- Put the gasket "E" (fig. 4) in the correct position
under the edge of the table top, so that the outer
side of the gasket fits perfectly with the external
perimeter of the worktop. The ends of the strips
must fit without overlapping.
FIG. 4
WARNING:
note that the adhesive which joins the plastic
laminate to the worktop must be resistant to
temperatures of no less than 150 °C to prevent
the covering from detaching.
The installer is advised that the rear wall,
adjoining and surrounding surfaces of the
barbecue must be resistant to a temperature
of 90 °C.
FIG. 5
9
FIG. 6
INSTALLATION
5) ELECTRICAL CONNECTIONS
When connection is made directly to the power
circuit:
- place a switch between the appliance and the
circuit of an appropriate size for the load of the
appliance and with a minimum aperture between
contacts of 3 mm.
- The means for disconnection must be
incorporated in the fixed wiring in accordance with
the wiring rules.
- Remember that the earth cable must not be
broken by the switch.
- The electrical connection may also be protected
by a high sensitivity differential switch.
It is strongly recommended that the yellow-green
earth cable provided be connected to a good earth
installation.
IMPORTANT: the appliance must be
installed following the manufacturer's
instructions. The manufacturer will not be
liable for injury to persons or animals or
property damage caused by an incorrect
installation.
The electrical connection must be made in
conformity with current rules and regulations.
Before making a connection, check that:
- the voltage matches the value shown on the
specification plate and the section of the wires of
the electrical system can support the load, which
is also indicated on the specification plate.
- The capacity and outlets of the electrical
installation are suitable for the maximum power
output of the appliance (see the information label
attached on the underside of the housing).
- The outlet or installation is provided with a ground
connection according to standards and provisions
currently in force. All responsibility is declined for
failure to comply with these provisions.
- If a power cord is not supplied with the appliance,
connect a cable with a suitable section to the
terminal board (see the table in paragraph 6)
keeping the ground wire longer than the lead
wires in conformity with the diagram in fig. 7.
When connection to the power circuit is made
through an outlet:
If the installation requires modifications to
the home's electrical system or if the
socket is incompatible with the appliance's
plug, have changes or replacements
performed by professionally-qualified
person. In particular, this person must also
make sure that the section of the wires of
the socket is suitable for the power
absorbed by the appliance.
Before performing any service on the electrical
part of the appliance, it must absolutely be
disconnected from the electrical network.
WARNINGS:
all our products are conform with the
European Norms and relative amendments.
The product is therefore conform with the
requirements of the European Directives
in force relating to:
- compatibility electromagnetic (EMC);
- electrical security (LVD);
- restriction of use of certain hazardous
substances (RoHS);
- EcoDesign (ERP).
- apply to power cable "C", if not provided, a
standard plug suitable for the load indicated on
the information label. Connect the wires as in the
diagram in fig. 7 taking care to observe the
responses listed below:
letter L (phase) = brown cable;
letter N (neutral) = blue cable;
symbol
(earth) = yellow-green cable.
- The power cord must be placed in a way that it
does not reach an temperature of 90 °C in any
position.
- To connect, do not use adaptors or switches as
they may cause false contacts resulting in
dangerous overheating.
- The outlet must be accessible after the built-in.
FIG. 7
10
MAINTENANCE
Before carrying out maintenance of any kind,
disconnect the appliance from the mains. All
maintenance must be carried out by authorized
personnel only.
Note, in the event the power cord is replaced:
- it must be replaced by the manufacturer, its
service agent or similarly qualified persons in
order to avoid a hazard.
- the ground wire must be left longer than the
lead wires (fig. 9) and the instructions in the
paragraph "ELECTRICAL CONNECTIONS" must
be observed.
To reassemble the appliance repeat the steps
above in the reverse order.
6) PART REPLACEMENT
To replace components located inside the
barbecue the resistance should be lifted up and
secured in the vertical position. Take out the drip
pan containing the lava stone and loosen the four
screws that are under it (see fig. 8). The work
surface can now be detached from the worktop
giving access to all internal components.
To reassemble the work surface of the appliance
take care not to damage the power cables and
make certain that they are well positioned in the
guides along the side of the appliance.
7) TECHNICAL SPECIFICATIONS OF
ELECTRICAL COMPONENTS
To facilitate the task of the installer a table with
component specifications is included below.
ELECTRICAL COMPONENTS OUTPUT
Name
W
Grill
2400
FIG. 8
FIG. 9
11
TECHNICAL SPECIFICATIONS
BARBECUE
Voltage
220 - 240 V ~
Frequency
50/60 Hz
Total nominal power
2400 W
WARNING: MAINTENANCE MUST ONLY BE
PERFORMED BY AUTHORIZED PERSONS.
12
TYPE AND SECTION OF POWER CABLES
TYPE OF
CABLE
TOTAL OUTPUT
OF APPLIANCE
SINGLE - PHASE
POWER SUPPLY
Rubber
H05 RR-F
2400 W
Section 3 x 1.5 mm
Policroroprene
H05 RN-F
2400 W
Section 3 x 1.5 mm
Policroroprene
H07 RN-F
2400 W
Section 3 x 1.5 mm
2
2
In case of failure or cut in the cable, please move away from the
cable and do not touch it. Moreover the device must be
unplugged and not switched on. Call the nearest authorized
service center to fix the problem.
13
2
TECHNICAL ASSISTANCE AND SPARE PARTS
Before leaving the factory, this equipment was tested and adjusted by skilled personnel so as to
guarantee the best operating results.
Original spare parts can only be found at our technical service centres and authorized stores. Every repair
or adjustment necessary thereafter must be carried out with the greatest care by qualified personnel.
For this reason we recommend you always contact the dealer you purchased it from or our nearest
service centre stating the make, model, series and type of problem experienced with the equipment. The
relevant specifications are stamped on the information label attached on the underside of the appliance
and on the label attached to the packing box. This information will allow the technician to procure the
appropriate spare parts and guarantee that the right action is taken promptly. It is recommended that you
note these specifications below so that they are readily available at all times.
MARK: .......................................................
MODEL: .................................................…
SERIES: ....................................................
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
This guideline is the frame of a European-wide validity of return and recycling on Waste Electrical and
Electronic Equipment.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement