Seiki | SC-9500AU7TL | Seiki SC-9500AU7TL User Manual

Seiki SC-9500AU7TL User Manual
9.5KG TOP
LOAD WASHING
MACHINE
INSTRUCTION
MANUAL
MODEL: SC-9500AU7TL
Please read this manual carefully before using, and keep it for future reference.
CONTENTS
General Safety4
Product Overview8
Getting Started10
Levelling the appliance11
Connecting the water inlet hose12
Connecting the Drain Hose13
Instructions14
Operations17
Cleaning and Maintenance19
FAQs21
Specifications22
Customer Helpline24
GENERAL SAFETY
IMPORTANT INFORMATION
Read this manual thoroughly before you start using the Top Load Washing Machine.
The safety precautions instructions reduces the risk of fire, electric shock and injury when
correctly complied to.
Please follow all instructions and take notice of all warnings.
Pay close attention to messages that follow this safety alert symbol or the words
DANGER, WARNING or CAUTION. These words will be used to alert you of
potential hazards that and injure you and others. Following these instruction will
tell you how to reduce the chance of injury and the possible dangers if
instructions aren’t followed.
4
WARNING
This symbol indicates when there is a serious risk of
injury if you do not pay attention to the warnings.
CAUTION
This symbol indicates when to be careful to
avoid a serious risk of injury to oneself or
damage to property.
GENERAL SAFETY INSTRUCTIONS (Cont.)
ELECTRICAL SAFETY
• Voltage: Plug the appliance to a 220-240V, 50Hz, properly earthed power
outlet, it must be in good working order.
• Power connection: Do not use an adaptor or an extension cord.
Plug the power plug directly into a separate power point that cannot be
accidentally turned off, and that is easily accessible so you can switch it off
if needed.
• Power cord: Do not kink or damage the power supply cord. Make sure it is
behind the appliance so no one can step on or place anything on the power
supply cord or against it. A damaged power plug may overheat and cause a fire.
• Damaged cord: Do not use a cord that shows cracks or damage. Any damage
to the cord may cause a short circuit, fire and/or electric shock.
Contact our support centre on 1300 296 699 for advice
• Disconnection: Never pull the power cord to unplug appliance. Grip the plug and
pull straight out from the power point.
• Electrical work: If the installation of this appliance requires any electrical work,
make sure it is carried out by an electrician.
To reduce risk of fire, electric shock or injury, always follow these basic precautions
and accident prevention measures when using this appliance, including the below:
NOTE: This appliance should be installed by an authorised technician else warranty
will be void.
INSTALLATION
• The product is heavy, be careful when moving it. To avoid back or other
injury, have 2 people lift or mechanical aid when installing.
• When unboxing, thoroughly inspect the appliance carefully for any
damage. If there is any damage, do not install the appliance. Contact our
support centre on 1300 296 699 for advice.
• While installing the appliance make sure that the power cord is not bent
or flattened.
• Make sure to remove all packaging materials such as foams and tapes
before installing the appliance.
• Make sure if the machine is to be placed on carpet that the ventilation openings
in the base are not obstructed
• Install the washing machine on a flat level and stable ground.
5
GENERAL SAFETY INSTRUCTIONS (Cont.)
USAGE CONDITIONS AND RESTRICTIONS
• Supervision over children is to ensure that they do not play with the
appliance. Never allow them to use, play with or crawl inside the appliance.
Cleaning and maintenance must not be done by children.
• This appliance is not to be used by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they are being supervised or been given instructions on how to use of the
appliance in a safe way and understand the hazards with using this
appliance incorrectly.
• Only for indoor domestic use only. It is not to be used for industrial or
commercial use.
• Do not use this product for anything other than its intended purpose, and only
use it as described in this manual. Do not attempt to alter or modify
this appliance.
• In the process of a hot wash, the door window can become hot. Make sure not to
touch it or that no children or pets come into contact with the door window.
• Ensure that emptying all pockets of every item to make sure that there is no
hard, sharp objects such as coins, safety pins, bra wires, nails or screws can cause
damage to the appliance and has a chance to block the pump.
• Damage or malfunction caused from foreign objects is not covered by your
warranty to the appliance.
• Do not operate this appliance outdoors.
• Incorrect use can result in property damage, injury or death. We assume no
liability for misuse of the appliance or noncompliance with these instructions.
6
GENERAL SAFETY INSTRUCTIONS (Cont.)
CLEANING AND MAINTENANCE
• Before cleaning or maintenance, always unplug the appliance from the power
socket. Make sure you pull by the plug, not the cord as this can damage the
power cord and cause a hazard.
• Only the filter requires regular cleaning, everything else is non user-serviceable
parts. Do not try to repair, disassemble or modify the appliance.
• Check and clean the lint filter on a regular basis
• Service: Never try to repair, modify or replace any part of the appliance, unless
this manual says you can do so. All other servicing is to be done by a qualified
technician, or contact our support centre on 1300 296 699 for advice.
7
PRODUCT OVERVIEW
8
PRODUCT OVERVIEW (Cont.)
CONTROL PANEL
8
7
6
5
4
3
2
1
1.
ON/OFF: ON/OFF button allows you to turn the appliance off or on.
2.
START/PAUSE: Press this button to start or pause the washing cycle.
3.
TEMPERATURE: Press the button to select the water temperature.
4.
PROGRAM: Before starting the washing machine, continously press the
“PROGRAM” button to select your desired program.
5.
DELAY: Press and hold the “DELAY” button and every 0.5secs it will
increase by an hour at a time, let go to reach your desired hour for your
wash to start its cycle. If you go to 24hours, it will beep once then return
back to 0.
6.
WATER LEVEL: Before washing, you can select the water level according to
how dirty the items are, materials or the weight.
7.
CHILD LOCK: After you have selected a wash program and the cycle
commences, you then press and hold ““SPIN” / “WATER LEVEL” buttons
until the indicator light for child lock is illuminated.
8.
FUNCTION: This will show the types of spins in process according to
the cycle thats in progress.
9
GETTING STARTED
Before installing your appliance, read all safety instructions in this manual,
especially the sections on electrical safety and installation.
UNPACKING
• When unpacking the appliance, be sure to keep all the packaging materials until
you have made sure your new appliance is undamaged and in good working
order. Plastic can be a suffocation hazard for babies and young children,
make sure the materials are out of their reach.
TRANSPORTATION
• CAUTION: VERY HEAVY! Be sure to team lift the appliance with someone or
mechanical aid is required when moving the appliance. Keep the appliance
upright as possible when moving the appliance.
IMPORTANT! Installing the bottom cover
• Make sure the power cord is unplugged from the
mains supply.
• Place some padding (such as a soft mat, blanket or
thick towel) on the floor and gently lay the washing
machine on the padding, back side down. Take care
not to dent the housing.
• Insert the bottom cover into the hooks of the leg,
pushing it straight until it reaches into the
front hooks.
• Ensure to fasten the bottom cover with the
supplied screws.
• Carefully set the washer upright.
10
GETTING STARTED (Cont.)
LEVELLING THE APPLIANCE
IMPORTANT! Make sure to level the appliance carefully with a spirit level to ensure
the most accurate levelling of the appliance. This is a must if your floor in
unbalanced to level the washing machine.
• Make sure to position the appliance on a level and stable ground. If the
floor is uneven you can adjust the feet by twisting the feet. Make sure to
slightly incline the appliance first then adjust the leveling feet by
twisting it clockwise or counter clockwise depending if you are raising or
lowering the feet.
• By placing a spirit level ontop of the appliance you can check correctly to
aid you in adjusting the feet levelling nuts to adjust the appliance to be
completely level.
Note: Make sure to avoid direct sunlight onto the appliance.
11
GETTING STARTED (Cont.)
CONNECTING THE WATER INLET HOSE
IMPORTANT! To prevent leakage or water damage please follow the below
instructions. Do not kink, crush, modify or sever the water inlet hose.
• Connect the inlet pipe as indicated, there are two ways of connecting
the inlet pipe.
• Minimum Inlet Water Pressure: 0.1MPa
Maximum Inlet Water Pressure: 0.6MPa
1. Connection between the Tap and inlet hose.
2. Connection between the screw tap and inlet hose.
Connect the other end of the inlet pipe to the inlet valve on the back of the
appliance and fasten the pipe tightly clockwise.
12
GETTING STARTED (Cont.)
CONNECTING THE DRAIN HOSE
• Do not kink or protract the drain hose. Position the drain hose correctly other
wise damage will result in water leakage.
• The height of the water drain hose can be from 86 to 100cm.
• Do not bend the drain hose or place it under the washing machine.
• Be sure to only use new hose sets when connecting the Washing Machine.
Do not re-use old hoses.
13
INSTRUCTIONS
BEFORE FIRST USE
• Make sure the washing machine is completely level as to previous instructions
on how to level your washing machine.
• Make sure the water inlet hose is installed correctly.
• Make sure that the washing machine is plugged into the power socket.
• When the water inlet hose is installed, turn on the water supply on the tap.
• Properly install and set up the upper drain hose at no less then the
height of 860mm, the water will overflow if it is below the recommended
height of 860mm.
• Before any first wash make sure everything is installed correctly. Make sure to
do one wash with the ‘DRUMCLEAN” wash program with no items inside to clean
out the tube before your first loaded wash.
After the above steps have been completed, In a few simple steps you can select
the type of wash you want and get started.
14
INSTRUCTIONS (Cont.)
• Make sure that the appliance is in a correct working temperature (0-40˚C).
If the appliance is used under 0˚C the inlet valve and draining system may
be damaged.
• Make sure that all labels are checked on items if they can be washed.
• Use non-foaming or less-foaming detergents which are more suitable for
washing machines to wash correctly.
WARNING
• Never use the washing machine to wash a single item at any given time, if you
need to urgently wash an item, we suggest placing a few clothing items in there.
• Make sure that all labels are checked on items if they can be washed.
• Use non-foaming or less-foaming detergents which are more suitable for
washing machines to wash correctly.
• Maximum mass of dry clothes is 9.5kg
15
INSTRUCTIONS (Cont.)
WASH CARE SYMBOLS
When choosing a wash program, check for any labels on your clothes and follow
the instructions. below are some commonly used symbols.
16
OPERATIONS
PROGRAMS
Select the desired programs according to the clothes that are being washed.
PROGRAMS
Standard
Standard fabric washing program suitable to wash
cotton fabrics.
Quick
Suitable to wash lightly stained clothes.
Blanket
Suitable to wash big sized items such as curtains,
bedsheets, blankets. Additional 15 minutes is added to
the cycle for more movement and soaking time.
Delicates
Low/Mid/High water level selection with a soft and
slow washing for delicate items placed in appliance.
Jeans
Suitable for washing heavy stained clothes and jeans.
Baby Clothes
Increasing the rinse times to reduce the detergent
residue on the clothes for baby/children clothes.
*Standard, water level 7 is the standard washing programs to which the
information in the energy efficiency label relates, and they are suitable to clean
normal soiled cotton laundry and they are the most efficient programs in terms
of energy and water consumption for washing that type of cotton laundry, the
actual water temperature may differ from the declared cycle temperature.
17
OPERATIONS (Cont.)
WASHING PROGRAMS TABLE
18
CLEANING AND MAINTENANCE
WARNING:
• Before starting maintenance, ensure that the appliance is unplugged and
close the tap.
CLEANING THE CABINET
Proper maintenance on the washing machine can extend its working life.
The surface can be cleaned with diluted non-abrasive neutral detergents when
necessary. If there is any water overflow, use a wet cloth to wipe it off immediately.
Make sure no sharp items are used to clean the appliance.
• Use a gentle cloth to wipe off the water and dirt on the surface of the
washing machine after every use. Detergent, properllant and other chmicals
are not allowed to be used to clean the washing machine surface as it can
damage the plastic accessories.
CLEANING THE WATER INLET
1 Switch on the power, followed by shutting off the tap
2 Let the washer work for 5 seconds so that the water flows into the tub
through the hose, then turn off the power.
3 Unload the water inlet hose and clean the mesh bag, then re-install everything.
19
CLEANING AND MAINTENANCE (Cont.)
CLEANING THE DRAIN PUMP FILTER
1 Drain the water out of the pump
under which you use a container to
collect the water.
2 Loosen the pump cover.
(anti-clockwise)
3 Take out the lint filter.
4 Clean the filter.
5 Restore it and adjust the
convex place to align at the
pump hole.
6 Tighten the pump cover
(clockwise)
20
FAQs
Please be sure to contact our call centre on 1300 296 699 if you cannot identify
the issue with the below information.
Problem
No water is flowing in
No washing
Solution
• Check to see if the power is on
• The water supply is cut off or the water
pressure is too low.
• The inlet hose is properly connected and the
water tap is opened.
• The filtering screen of inlet valve is blocked by dirt.
• The coil of the inlet valve is damaged.
• Make sure the Start/Pause button hasnt
been pressed.
• If the power is off or fuse has burned out
• The power supply voltage is too low
• The water amount reaches to the requiredwater
level. (The washer will not work if the water
amount does not reach the required water level)
• If it is set on “delay” then the washer will not
start until time is reached.
Abnormal draining
• The water drain hose is placed to high.
• The internal rubber ring of drain valve is blocked.
Abnormal Spin
• Make sure the door lid is closed.
• If all clothing piled largely at one side of the barrel.
• The appliance must be placed completely level for
it to work correctly.
NOTE: During the de spin process of a washing cycle. If the washing is piled at one
side it will cause an unbalance of the barrel. The washing machine computer will
feel this unbalance and will automatically try to correct it, if its unable to correct
in in three tries, then you will have to manually open, pause the cycle and evenly
place the clothing inside the barrel to solve the problem.
21
SPECIFICATIONS
Power Supply
240V~50Hz
Standard Water Pressure
0.1MPa~0.6MPa
Washing Capacity
9.5KG
Rated Input Power
600W
Dimensions
601 x 625 x 1015 mm
Weight
45kg
22
23
CUSTOMER HELPLINE:
1300 296 699
DISTRIBUTED BY:
Ayonz Pty Ltd
24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising