Glem | FC64GWI | Glem FC64GWI User Manual

Glem FC64GWI User Manual
Installation and Operating Instructions
Built in GAS Cooktops
Please note: This cooktop must be installed by an authorised
installer. The enclosed installation check list must be completed and
signed off by the installer with the installer’s Licence number recorded
to activate the Warranty.
Call Service 1 300 307 917
2
SAFETY PRECAUTIONS
IMPORTANT! This booklet is a fundamental part of the appliance, it should be retained.
Read all instructions carefully before using the appliance.
This appliance is to be installed by a qualified technician in accordance with the gas
installation code AS5601, SAA wiring rules, as well as the requirements of all local
statutory and building authorities and regulations. This appliance is for domestic use
only and has been designed for cooking and heating food. Any other use is considered
improper.
The manufacturer is not responsible for bad installation, tampering, unskilled use and
usage other than that it is intended for.
•
•
Check that the product has not been damaged during transport.
Packing elements (plastic bags, expanded polystyrene, nylon etc) are potentially
dangerous and must be kept away from children.
•
•
Packing is made up of recyclable material and is marked by the
symbol.
This appliance is only to be used by adults. Make sure the children do not touch the
controls or play with the appliance.
Do not try to modify the appliance. In the case of faults, do not attempt repair but ask
for assistance from a Glem Gas Service Agent.
The data plate with its technical data is in a visible position under the housing. There
is another data plate enclosed that should be attached to a handy surface for future
reference. The data plate under the housing must never be removed.
The illustrations for using the appliance are in the final pages of this booklet.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS
IN OPERATION
NOT SUITABLE FOR USE IN MARINE CRAFT, CARAVAN OR MOBILE HOME
WARNING: CERAMIC COOKTOPS – IF THE SURFACE IS CRACKED SWITCH
OFF THE APPLIANCE AND CALL FOR SERVICE TO AVOID ANY POSSIBILITY
OF ELECTRIC SHOCK.
WARNING: ACCESSIBLE PARTS BECOME HOT IN USE. TO AVOID BURNS AND
SCALDS CHILDREN SHOULD BE KEPT AWAY.
DO NOT MODIFY THIS APPLIANCE.
•
•
•
•
•
•
•
•
Safety hints and usage tips
•
•
•
•
After use ensure that all controls are in the off position
Never leave cooking food unattended during use as this can lead to a fire risk.
Be aware of wearing loose garments while cooking as these may catch vessel handles
or catch fire.
Always turn pan handles to the side or to the back of the cooktop where they can’t be
knocked or reached by children.
3
COOKTOP IDENTIFICATION
Warning:
This appliance is designed to be built into a kitchen bench capable of withstanding the weight
of the appliance during its use.
♦ The kitchen bench must be resistant to temperatures of at least 100°C. Check with the
manufacturer of the bench material to be sure. No liability will be accepted for damage to
bench materials that do not comply
♦ See the relative paragraph and drawings for correct installation.
♦ Using a gas cooking appliance causes heat and humidity in the location where it is installed.
Make sure that the kitchen is adequately ventilated, install a range hood if required. See
fig. 16 & 17.
This booklet covers several models. You can see your model number on the data plate:
MODELS
60cm cooktop with Large burner Emilia SEC64GI – FIG.1
1. Medium front burner
2. Medium back burner
3. Small burner
4. Large burner
60cm cooktop with Wok burner
5. Medium front burner
6. Medium back burner
7. Small burner
8. Large Wok burner (Glem FC64GWI - FIG.4)/Wok burner (Emilia SEC64GWI - FIG.2)
70cm cooktop with centre Wok burner
Emilia SEC75GWI – FIG. 3
1. Small burner
2. Large burner
3. Medium back burner
4. Medium front burner
5. Wok burner
75cm cooktop with 5 burners
Glem FC75GSWI – FIG. 6
1. Small burner
2. Large burner
3. Medium back burner
4. Medium front burner
5. DUAL control Wok burner
90cm cooktop with 5 burners
Glem FC95GWI – FIG. 6
1. Small burner
2. Medium back burner
3. Large burner
4. Medium front burner
5. DUAL control Wok burner
4
75cm cooktop with 4 burners
Glem FC74GSWI – FIG. 5
1. Small burner
2. Large burner
3. Medium back burner
4. DUAL control Wok burner
LIGHTING THE GAS BURNERS
Gas burners
The flow of gas to the burners is regulated by the controls knobs. Depending on the model, the
graphic symbols are printed on the knobs or the control panel (Fig. 10). The indicator symbols
are:
Valve closed, no gas flow
Maximum capacity, maximum gas flow
Minimum capacity, minimum gas flow
Turning On and Off
Each control knob is clearly marked with the burner that it controls.
Lighting with electronic ignition
These models are identified with the
symbol near to the
symbol (maximum flow).
To light one or more burners, press and turn the knob to maximum flow and hold it down until
the burner is lit; turn the knob until the desired flame is obtained.
Note:
If it is difficult to light the burner with the knob in the maximum position because of local
gas flow, we recommend repeating the operation with the knob turned to a lower level.
Lighting without electronic ignition
To turn on burners without electric ignition, or when there is no electrical power in models with
ignition, place a flame near to the upper part of the burner, press and turn the knob anti-clockwise
so that it points to the
symbol on the panel. To turn the burner off, turn the knob clockwise
until it points directly upwards.
Burners with safety valves
Some models have safety valves which automatically interrupts gas flow should the flame be
extinguished for any reason.
Turn the gas control knob to maximum and then press and hold it down for about 4 to 5 seconds.
Release the knob and adjust the flame by turning the knob until it reaches the desired intensity.
Warning:
Do not activate the electronic ignition for longer than 15 seconds.
If it still has not lit after this time, wait for 1 minute before repeating the operation.
Dual Control Wok Burners
Cooktops fitted with Dual control wok burners have the latest in gas cooking burner technology.
Dual control means that the burner can be used for a variety of cooking applications. One control
operates the gas flow to the centre burner for simmering and low heat and the other control
operates the outer ring for large vessels and woks. The burners operate independently of each
other and can operated separately or in tandem for maximum output.
5
USING THE GAS COOKTOP
Pan supports (trivets)
The trivets were designed to make the cooktop easy and safe to use. We recommend checking
their exact position and stability on the cooktop before each use. Furthermore, check that the
supporting rubbers are integral and correctly positioned.
Small vessel support (Fig.8)
Only use the auxiliary burner ring (the smallest) for vessels with a small diameter to prevent
them from tipping and to maximise efficiency.
WOK Burner stand (Fig.9 optional – design may vary to image)
Only use the wok stand for WOKs (concave bases). In order to avoid serious burner malfunction,
we recommend using the wok stand at all times for Woks with curved bases but do not use it for
vessels with flat bottoms.
Choosing the burner
Choosing the most adapt burner depends on the vessels’ diameter and capacity (see table).
It is important that the pan’s diameter matches the burner power to maximise efficiency.
Burner
Auxiliary
Semi-rapid
Rapid
Triple crown wok
Dual control
Pan diameter
Minimum diameter
60 mm (with reduction)
160 mm
200 mm
240 mm
240 mm
Maximum diameter
140 mm
200 mm
240 mm
260 mm
260 mm
GAS COOKTOP INSTALLATION
Installation on the kitchen bench
The cooktop can be installed on materials as long as they are heat-resistant (minimum
temperature 100°C). Clearances from combustable surfaces must be 120mm all around to
comply with AS5601 regulations.
The size of the hole to be cut into the kitchen bench and the minimum distance between the
back, side and overhead walls are shown in figures 12, 13, 14, and 15.
Note that:
1. When the cooktop is installed over a vacant cavity (ie without oven below) a separate
panel must be installed beneath the underside of the cooktop base at a distance of at least
10 mm.
2. When the cooktop is installed over an oven a divider panel at a minimum distance of 15mm
is required, and following the oven supplier’s instructions, maintaining ventilation as
specified in fig. 19.
3. The electrical connection of the two appliances must be carried out separately.
4. We recommend the use of ovens equipped with forced internal cooling such as all models
from Glem and Emilia.
6
Fixing the cooktop
The cooktop is to be fixed to the bench as follows:
1.
Place the sealing gasket supplied along the outside edge of the hole cut into the bench
so that the ends of the strips are perfectly joined without overlapping.
2.
Position the cooktop into the hole in the bench making sure it is centered.
3.
Attach the cooktop to the bench with the supplied mounts as shown in fig. 16.
4.
When the sealing gasket is correctly installed, it will protect the cooktop from intrusion of
liquids.
Connecting the gas
The instructions are for a qualified installer.
The appliance must be installed correctly, conforming to the laws in force.
Remove the electrical power supply before servicing the appliance.
Gas Inlet Connection Point
Model SEC64 – 519mm from left hand edge of cut out, 40mm from rear edge.
Model FC64,SEC75, F74, F75 – 215mm from left hand edge of cut out, 40mm from rear edge
Model FC95 – 799mm from left hand edge of cut out, 40mm from rear edge
These technical instructions have been prepared for the use by Authorised persons. The
requirements of the local Gas and Electrical authorities must be adhered to, consult
AG601/AS5601 as appropriate.
•
•
•
•
•
•
Before installation, make sure that the gas type (natural gas and LPG) and the
cooktop are compatible. To do this, check the data on the product plate on the
cooktop and on this booklet.
Gas inlet fitting is ½” BSP (male) thread.
The gas connection is identified in table figure 7A.
Fit regulator supplied for natural gas or supplied LPG test point (as applicable)
It is recommended that an isolating valve and union be fitted, to enable simple
disconnection for servicing. These are to be in an accessible location.
Check connections are gas tight with soapy water or other approved method
Flexible Hose Connection
Install with a hose assembly that complies with AS/NZ1869 (AGA Approved). 10mm ID class
Bor D and in accordance with AS5601. This hose must not exceed 1.2m in length. Ensure that
the hose does not contact the hot surfaces of the cooktop or oven or any other appliance that
may be installed underneath or adjacent to the cooktop. The hose must not be subject to contact
from drawers, abrasion or kinking. All joints must be checked for leakage using soapy water.
Final Check
Operate the burners on high and low flames and check that each burner ignites properly and
has a stable flame. The following may be abnormal:
• If the burners have yellow tipping
• If the pots are sooting underneath
• If the burners fail to ignite properly
• If the burners fail to remain alight
When satisfied with the operation of the cooktop please explain to the user the correct method
of operation. If the appliance can not be adjusted to operate correctly refer to Glem Gas for
further assistance.
7
CONVERSION TO DIFFERENT TYPES OF GAS
Should the cooktop need to be converted to a gas different to the one it was intended for, the
injectors must be replaced.
It there are no spare injectors supplied they can be obtained from Glem Gas Service.
The injectors are to be installed according to the table on the underside of the cooktop.
Injectors can be identified by the diameter expressed in hundredths of mm printed on the injector
itself.
Modify the inlet gas supply as required and fit either the Natural gas regulator or LPG test
point as appropriate.
Replacing the injectors
1. Remove the gas rings and burner caps from the cooktop.
2. Using a face spanner, replace injectors “J” (fig. 20) with those specified for the gas to be
used.
3. Reassemble the burners. The burners do not require primary air regulation
Regulating the minimum
Having replaced the injectors, ignite the burner and remove the control knob. Turn the knob to
minimum, insert a screw driver and rotate screw to decrease the flame or unscrew it to increase
the flame. (fig. 20)
The result should be a small constant flame which is even all around the burner crown.
Finally, check that the flame does not go off when quickly turning the valve from maximum to
minimum. On cooktop fitted with flame failure devices, check that the flame slightly brushes the
thermocouple. Check correct regulation by leaving the burner on for a few minutes. If it goes
off, increase the minimum.
Gas checks and adjustments – Pressure Adjustment
First shut off the gas to the appliance. Remove the sealing screw from the regulator test point
or LPG test point at the rear of the cooker and attach a hose from the mamometer to the point.
Turn the gas back and light the largest burner and smallest burner at the maximum setting.
Check the pressure and adjust at the regulator if necessary to the settings in the tableor on the
data plate. For LPG adjust at the regulator at the cylinder. Turn the regulator adjusting screw
clockwise to increase the pressure and anti clockwise to reduce the pressure. Refit the test
point sealing screw when finished.
CLEANING
To maintain the cooktop it needs to be cleaned after each use once it has cooled down.
Never remove the knobs from their housing to clean the cooktop.
Enamel parts
All enamel parts should only be washed with a sponge and soapy water or other specifically
non-abrasive products. Dry completely.
Stainless Steel
The stainless steel plate should be cleaned with a damp cloth or with specific stainless steel
cleaning products.
8
After rinsing, dry with soft cloth. Avoid spray cleaners directed onto the graphics and take
care when wiping not to damage the printed graphics on the cooktop.
Cast Iron Trivets
Wipe the trivets with a damp cloth once they have cooled. Do not use cleaning agents or harsh
detergents to clean and dry carefully to prevent spotting or marking. This is important.
Burners
The burners are made up of two pieces and can be removed and cleaned with suitable products.
After cleaning they must be completely dried and replaced exactly into their housings.
• Models with electrical ignition: make sure that electrode “E” (fig. 21) is always clean.
• Models with safety devices: clean probe “T” (fig. 21) so that the safety valve works
properly. The electrode and the probe must be cleaned carefully.
Afterwards, replace the burners precisely into their housings.
To avoid damaging the electric ignition, avoid using it when the burners are not in place.
Ongoing Maintenance
The cooktop will not need specific maintenance; however, we recommend a full check at least
once every two years.
Should the control knobs become tight to turn or there is a smell of gas, close the main valve
and call for service. The faulty valve may need to be replaced.
GAS CONSUMPTION AND INJECTOR SIZES
Burner & Model
Dual Wok Burner
Large Wok Burner
Wok Burner
Large Burner
Medium Burner
Small Burner
Natural Gas
Inj Diam
MJ/H
0.75
1.20
1.75
1.70
1.40
1.10
0.90
16.5
14.6
14.0
10.0
6.1
4.0
Gas
Press
1.0
1.0
1,0
1.0
1.0
1.0
Inj Diam
0.49
0.64
0.98
0.97
0.90
0.69
0.53
LPG
MJ/H
15
13.8
13.0
11.0
6.9
3.8
Gas
Press
2.75
2.75
2.75
2.75
2.75
2.75
9
DIAGRAMS
Fig. 1
Fig. 2
2
2
1
1
3
3
4
4
Fig. 3
Fig. 4
2
3
5
4
1
3
2
1
4
4
3
5
2
1
2
Fig. 5
3
1
4
Fig. 6
10
Fig. 7
Fig. 7A
2
1
5
3
4
Fig. 8
Fig. 9
Fig. 11
Fig. 10
Fig. 12
11
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 19
12
Fig. 21
Fig. 20
13
GLEM GAS AUSTRALASIA PTY. LTD. PRODUCT WARRANTY
Thank you for choosing a Glem Gas Appliance, the purchase of this appliance is an important investment in your home and so to protect your
investment we urge you to complete the registration card attached, please return it immediately.
IT IS A WARRANTY REQUIREMENT THAT PROOF OF PURCHASE BE PROVIDED PRIOR TO REQUESTING A SERVICE CALL.
THIS WARRANTY SHALL NOT APPLY IF THE APPLIANCE WAS NOT INSTALLED BY A LICENSED TECHNICIAN AND PROOF IS NOT
SUPPLIED.
The benefits conferred by this warranty are in addition to all other conditions and warranties in respect of this product which the consumer may
have under the Trade Practices Act 1874 of the Commonwealth of Australia and/or similar State or Territory Laws.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Glem Gas Australasia Pty Ltd warrants, this appliance to be free from defects in workmanship and materials for a period of:
a) Where the appliance is intended to be used and is used for DOMESTIC USE – 24 MONTHS FROM DATE OF DELIVERY TO THE ORIGINAL
PURCHASER.
b) Where the appliance is intended to be used and is used for COMMERCIAL USE – 90 DAYS FROM DATE OF DELIVERY TO THE ORIGINAL
PURCHASER.
Glem Gas Australasia Pty Ltd, during the period of warranty, will at its option, and subject to the terms and conditions stated below, repair or
replace free of charge this appliance or any component part, which upon examination by Glem Appliances P/L. is found to be defective.
THIS WARRANTY SHALL NOT APPLY:
a)
If the rating plate has been removed or the serial number or other details on it have been removed or rendered illegible.
b) If the appliance is connected to any gas type or voltage other than shown on rating plate.
c)
If the appliance has been subjected to misuse, abuse accident or want of care.
d) If the appliance has been installed, operated or maintained contrary to the instructions supplied by Glem Gas Australasia Pty Ltd.
e)
If any defect or failure is due to connection to an inadequate or faulty gas or power supply.
f)
If damage is caused by foreign objects in or on the appliance or by reason of its use for purposes other than that for which it was delivered.
g) If a repair has been made or attempted by the purchaser.
h) Where the oven is installed outside an 80km radius from the GPO of any Australian Capital City to freight and travel costs beyond that radius.
Parts covered under warranty that need replacing i.e.: seals, knobs and burner caps. These can be posted to customer to put on at their
discretion.
This Warranty is given by Glem Gas Australasia Pty Ltd and no other person or organisation is authorised to vary its provisions and conditions.
Complete this section and keep it for your own record.
Appliance type
Purchased from
Model No.
Serial no.
Date of purchase
Please complete the section below and return to:
Glem Gas Australasia Pty. Ltd, PO Box 63 Blaxcell PO South Granville or fax to 02 9721 2766
Appliance type
Model No.
Serial no.
Purchased from
Customer Name
Installers Name
Date of purchase
Address
Installers licence no.
Installers Signature
Installers Compliance Number COMPULSORY FOR WARRANTY
PLEASE NOTE THAT THE INSTALLER MUST BE A LICENCED GAS FITTER
GLEM GAS AUSTRALASIA PTY. LTD.
P.O. Box 63 Blaxcell PO South Granville NSW 2142
Phone: 02 9721 2755 – Fax: 02 9721 2766 – www.glemgas.com.au
Email us info@glemgas.com.au
Free call 1 300 307 917
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising