Fisher & Paykel HS90X4 User Manual

Fisher & Paykel HS90X4 User Manual
INSTALLATION INSTRUCTIONS
USER GUIDE
Built-in Slideout Rangehood
HS60XW4, HS60LXW4, HS60LRX4
and HS90X4 models
NZ AU
CONTENTS
Safety and warnings
3
Installation instructions
5
Operating instructions
10
Cleaning and maintenance
11
Parts and accessories
13
Manufacturer’s Warranty
14
Customer Care
16
IMPORTANT!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may not
be available in all markets and are subject
to change at any time. For current details
about model and specification availability in
your country, please go to our local website
listed on the back cover or contact your local
Fisher & Paykel dealer.
Registration
Register your product with us so we can
provide you with the best service possible.
To register your product visit our website:
www.fisherpaykel.com
1
SAFETY AND WARNINGS
!
WARNING!
Electric Shock Hazard
All electrical work must be done in accordance with local and/or
national electrical codes as applicable. If you are unfamiliar with
methods of installing electrical wiring, employ the services of a
qualified electrician. Turn off power at service entrance before
installing wiring or servicing this product.
!
11.2 kg
(HS90X4)
WARNING!
Weight Hazard
The rangehood is heavy. Please ensure adequate care is taken when
installing the rangehood to prevent personal injury. The rangehood
must be installed onto a solid wall, stud, beam or truss. Weight of the
product is 11.2 kg (HS90X4) / 11 kg (HS60XW4) / 8.3 kg (HS60LRX4)
/ 8.1 kg (HS60LXW4).
11 kg
(HS60XW4)
8.3 kg
(HS60LRX4)
8.1 kg
(HS60LXW4)
IMPORTANT SAFETY INSTRUCTIONS
WARNING! When using this appliance always exercise basic safety precautions
including the following:
●●
●●
●●
●●
●●
●●
●●
●●
Please read the entire set of instructions before installing or using this appliance.
Please make this information available to the person installing the appliance –
doing so could reduce your installation costs.
Always switch the power off prior to installation, servicing or cleaning of the rangehood.
This appliance must be installed and connected to the mains power supply only
by a suitably qualified person according to these installation instructions and in
compliance with any applicable local building and electricity regulations. Failure to
install the appliance correctly could invalidate any warranty or liability claims.
To comply with electrical safety regulations, the rangehood must be plugged into
a socket near the appliance. The socket must be accessible, or have an accessible
isolating switch, to enable the end user to isolate the rangehood from the power for
the purpose of internal cleaning or maintenance.
A power outlet should be within 750 mm of the motor assembly and can either be on
the wall, behind the chimney or in the ceiling.
If the supply cord of this equipment is damaged, it must only be replaced by the
manufacturer, its service agent or similarly qualified person in order to avoid a hazard.
Ducting accessories are not supplied. All ducting must comply with local requirements
and building codes.
3
SAFETY AND WARNINGS
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
4
Attention should be given to ensure that any applicable regulations concerning the
discharge of exhaust air are fulfilled.
Before connecting any pipes, consult municipal ordinances to ensure that any
applicable regulations concerning the discharge of exhaust air are adhered to and
request permission from the person in charge of the building.
Exhaust air must not be discharged into an existing flue that is used for exhausting
fumes from appliances burning gas or other fuels.
There shall be adequate ventilation of the room when the rangehood is used at the
same time as appliances burning gas or other fuels.
The minimum distance between the supporting surface for cooking vessels on the
cooktop and the lowest part of the rangehood shall be 600 mm or 650 mm if installed
over a gas cooktop.
Stainless steel is very easily damaged during installation if abraded or knocked by
tools. It is recommended to protect the top of the rangehood with cardboard or
polystyrene during the installation to minimise the risk of damage occurring.
To reduce the risk of damage occurring to the cooktop, it is recommended that
the surface of the cooktop is protected with cardboard or a similar object during
installation of the rangehood.
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure they do not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
You must read the details concerning the method and frequency of cleaning.
There is a fire risk if cleaning is not carried out in accordance with the instructions.
Never leave frying food unattended since grease can overheat and catch fire. The risk
of fire is even greater in the case of used oil.
Do not flambé under the rangehood.
Never use the rangehood without the filters in place.
During an electrostatic discharge (ESD) it is possible that the device will stop
working. By switching the device off and on the device will again work as intended.
CAUTION: accessible parts may become hot when used with cooking appliances.
Remove all packaging, including protective wrappings, before use.
INSTALLATION INSTRUCTIONS
Contents of packaging
INSTALLATION INSTRUCTIONS
USER GUIDE
Built-in Slideout Rangehood
HS60XW4, HS60LXW4, HS60LRX4
and HS90X4 models
NZ AU
Rangehood
(1)
Installation instructions
User guide manual
(1)
Screw M6 x 40 mm
(incl. washer)
(4)
Handle (1)
(HS60XW4)
(HS60LXW4)
Carbon filters (2)
(HS60LRX4)
Screw 3 x 12 mm
(6)
Ducting adapter –
top extraction
(1)
Ducting adapter –
rear extraction
(1)
Duct hole covers
(2)
Spacer Rear
(2)
Spacer Lateral
(2)
5
INSTALLATION INSTRUCTIONS
Product dimensions
Power cord
D
C
F
A
B
E
HS60LRX4
HS90X4
HS60XW4
HS60LXW4
mm
mm
mm
180
180
180
B Overall width of product
598
898
598
C Overall depth of chassis
280
280
280
D Overall depth of chassis (fully extended)
460
460
460
PRODUCT DIMENSIONS
A
Overall height of product
E Height of handle
F
Installed chassis height
Power cord length
IMPORTANT!
70
40
40
140
140
140
1500
1500
1500
Actual product dimensions may vary by ± 2 mm.
Please read the entire instructions before installing the rangehood.
6
INSTALLATION INSTRUCTIONS
Height of rangehood
Please read the entire instructions BEFORE installing the rangehood.
●●
●●
●●
Ascertain the desired installation height of the rangehood.
When installing the rangehood, the lower edge of the unit must be a minimum of
600 mm above electric cooktop surface; 650 mm above gas cooktop cooking surface;
and up to a maximum of 750 mm.
Any installation above 750 mm will compromise the extraction performance.
C
A
D
B
Gas Burner
B
2 mm
Panel heights
Positioning
RECIRCULATED
MINIMUM CLEARANCES
A Height (top of cooktop to base of rangehood)
Electric cooktop
Gas cooktop
HS60LRX4
HS60LXW4
DUCTED
HS60XW4
HS60LXW4
HS90X4
mm
mm
min. 600 – max. 750
min. 650 – max. 750
min. 600 – max. 750
min. 650 – max. 750
min. 781 – max. 931
min. 831 – max. 931
min. 781 – max. 931
min. 831 – max. 931
B Height (top of cooktop to base of shelf where
rangehood is attached)
Electric cooktop
Gas cooktop
C Depth of installation (cabinet cavity)
min. 283
min. 283
Height of installation (cabinet cavity)
max. 108
max. 138
D
7
INSTALLATION INSTRUCTIONS
Venting options
Attention should be given to ensure that
any applicable regulations concerning
the discharge of exhaust air are fulfilled.
Ducted
We recommend rangehoods be vented
outside, recirculating installation is
recommended only when vented
installation is not possible. For optimal
efficiency, use smooth-walled ducting.
Flexible ducting should only be used as
last resort; it may reduce performance
and increase noise.
●●
●●
We recommend to use top extraction
for venting.
Top extraction (125 mm round ducting)
and rear extraction (100 mm round
ducting) can be used in conjunction
with this model.
Recirculating
Recirculating installation is
recommended only when vented
installation is not possible.
●●
●●
●●
Ducting through roof
Ducting through cavity to side
HS60LRX4 is designed for front
recirculating installations only.
HS60LXW4 can be installed in
front recirculating, or can be ducted.
Accessories are required.
HS60XW4 and HS90X4 can be installed
to recirculate through cabinetry with
ducting, or ducted outside.
Front Recirculating*
8
* In recirculating mode you must use carbon filters to
eliminate cooking smells and tall handle (70 mm).
INSTALLATION INSTRUCTIONS
WARNING!
Failure to install the screws or
fixing device in accordance with
these instructions may result in
electrical hazards.
A
Installation
1 Preparing the rangehood for installation:
Fig.1 Preparing for install
●●
●●
●●
●●
●●
●●
●●
●●
●●
●●
Before commencement, unpack
the rangehood and check that it
functions correctly.
Ø125 - 130 mm
Ensure the overhead cabinets are built
according to the minimum clearances
table on page 7.
Before drilling any holes, check that the
area behind the surface to be drilled is
209 mm
clear of any electrical cables or pipes etc.
Ducted installation
(HS60LXW4, HS60XW4, HS90X4)
If the rangehood is to be installed as a
ducted hood:
Do not remove cover tape (A), See Fig.1.
This is removed for recirculating only.
Place adaptor in top extraction.
Place cover on rear extraction.
FIG. 4
Wall
210 mm
35 mm
453/753 mm
Fig.2 Mounting to underside of cabinetry
FIG. 8
Front Recirculating installation
(HS60LXW4, HS60LRX4)
If the rangehood is to be installed as a
recirculating hood:
Remove cover tape (A), see Fig.1.
Place covers on rear and top extraction.
Install carbon filters see page 12.
Assemble tall handle (70 mm)
Fig.3 Spacer Lateral
2 Mounting the rangehood
Mounting to underside of cupboard
Fix the rangehood to a shelf mounted
at the right height in your wall units,
by drilling 4 holes, 7 mm in diameter,
(see Fig.2) and fixing with the 4 screws
supplied. When installing the rangehood
the space between the product and the
wall shall be covered with the adjustable
lateral and rear spacer supplied (Fig.3
and Fig.4).
FIG. 5
Screw shall be fixed into
lower face of the hood
FIG. 6
Fig.4 Spacer Rear
9
OPERATING INSTRUCTIONS
Control panel features
Left hand side
Right hand side
Light switch: the light can
be operated independently
from the fan.
Fan switch: the fan can be run at
different speeds depending on
the cooking requirements.
Fig.5 Light switch
Fig.6 Fan switch
Operating instructions
1 Pull out the front panel more than 50 mm. The front panel has to be pulled to its maximum
extension so as to optimise the extraction capacity.
2 Switch on the lamps (Fig.5).
3 Select air flow speed to suit your cooking requirements. The fan switch (Fig.6) has the
following functions:
0 Stop
I Low speed
II High speed
Front panel
10
CLEANING AND MAINTENANCE
WARNING!
Unplug or disconnect the appliance from the power supply before servicing or cleaning.
IMPORTANT!
●●
●●
Never use abrasive or oil based cleaners.
Wear gloves to protect against sharp edges.
General maintenance
The manufacturer is not liable for any damage caused by not following these instructions.
The rangehood should be cleaned regularly using warm water with soap or mild liquid
detergents. This ensures that no build-up of grease occurs as these deposits are
corrosive. Do not use abrasives or harsh detergents/cleaning fluids.
Note: in areas of high humidity and coastal environments cleaning should be carried out
more frequently.
Aluminium filter
The grease filter must be periodically cleaned (at least every two months).
Remove the grease filter and wash either by hand using hot soapy water or place in the
dishwasher with recommended dishwashing detergent for your dishwasher.
●●
●●
Note:
Some discolouration of the frame may occur.
When installing or replacing a filter, remove the protective plastic covering from the filter.
11
CLEANING AND MAINTENANCE
WARNING!
When replacing the bulb, let the bulb cool, and assure that power to the rangehood has
been turned off. Use new bulbs according to that indicated on the rangehood nameplate.
Carbon filter for all recirculating installations
(Optional: HS60LXW4, HS60XW4, HS90X4)
(With product: HS60LRX4)
Active carbon filters are disposable items designed to remove grease and odours from
cooking vapours before the air is channelled back into the kitchen. The active carbon
filters must be replaced periodically to work properly, at least every three months,
depending on the frequency with which the rangehood is used.
●●
●●
Note:
Fully saturated carbon filters can become a barrier to air movement, impeding the
rangehood’s performance.
In the event of fire, fully grease laden filters could be flammable and therefore regular
replacement is recommended.
Replacement
To replace carbon filters (C), proceed as follows:
1 Remove aluminium filter (A).
2 To remove carbon filter undo and remove the screw (B).
3 To install follow above steps in reversed order.
A
C
B
C
C
B
Fig.7 carbon filter replacement
B
1
2
3
4
B
Light bulb replacement
(230 Volt / 50 Watt light bulb)
To replace a light bulb, first disconnect rangehood from power supply.
Apply finger pressure to the face of the light bulb and twist one quarter turn anticlockwise, the light bulb will now be free to drop out.
Remove the faulty bulb and fit replacement bulb into the lamp holder.
Refit the light bulb, applying finger pressure and twist one quarter turn clockwise.
Note: replacement bulbs are not covered by Manufacturer’s Warranty.
12
PARTS AND ACCESSORIES
ACCESSORY
PART NUMBER
Replacement aluminium filter x2 (HS60)
792391
Replacement aluminium filter x2 (HS90)
792392
Recirculation charcoal filter x2
792390
Halogen bulb
792461
Ducting kit 125 mm (eaves)
PD-RHK125E
Ducting kit 125 mm (wall)
PD-RHK125W
Ducting kit 125 mm (roof)
PD-RHK125T
13
MANUFACTURER’S WARRANTY
You automatically receive a 2 year Manufacturer’s Warranty with the purchase of
this Slideout rangehood covering parts and labour for servicing within the country
of purchase.
Fisher & Paykel undertakes to:
Repair or, at its option, replace without cost to the owner either for material or labour
any part of the product, the serial number of which appears on the product, which is
found to be defective within TWO YEARS of the date of purchase.
Note: this Manufacturer’s Warranty is an extra benefit and does not affect your
legal rights.
This Manufacturer’s Warranty DOES NOT cover
A Service calls which are not related to any defect in the product. The cost of a service
call will be charged if the problem is not found to be a product fault. For example:
1 Correcting the installation of the product.
2 Instructing you how to use the product.
3 Replacing house fuses or correcting house wiring or plumbing.
4 Correcting fault(s) caused by the user.
5Noise or vibration that is considered normal, eg drain/fan sounds, refrigeration
noises or user warning beeps.
6 Correcting damage caused by pests, eg rats, cockroaches, etc.
7 Replacement light bulbs.
B Defects caused by factors other than:
1 Normal domestic use; or
2 Use in accordance with the product’s user guide.
C Defects to the product caused by accident, neglect, misuse or ‘act of God’.
D The cost of repairs carried out by non-authorised repairers or the cost of correcting
such unauthorised repairs.
E Normal recommended maintenance as set out in the product’s user guide.
F Repairs when the appliance has been dismantled, repaired or serviced by other than a
Fisher & Paykel Authorised Repairer or the selling dealer.
G Pick-up and delivery.
H Transportation or travelling costs involved in the repair when the product is installed
outside the Fisher & Paykel Authorised Repairer’s normal service area.
Nothing in this Manufacturer’s Warranty is intended to, or does, limit any rights you may
have under law to recover the costs of inspecting or returning the goods to us.
This product has been designed for use in a normal domestic (residential) environment.
This product is not designed for any commercial use (whatsoever). Any commercial use
by a customer will affect this product’s Manufacturer’s Warranty.
Service under this Manufacturer’s Warranty must be provided by a Fisher & Paykel
Authorised Repairer (refer to the ‘Customer Care’ section at the back of this book). Such
service shall be provided during normal business hours. This Manufacturer’s Warranty
certificate should be shown when making any claim.
14
MANUFACTURER’S WARRANTY
For Australian customers
This Manufacturer’s Warranty is an extra benefit and does not affect your legal rights.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Please keep this user guide in a safe place.
15
CUSTOMER CARE
Before you call for service or assistance...
Check the things you can do yourself. Refer to your user guide and check that:
1 Your product is correctly installed.
2 You are familiar with its normal operation.
If after checking these points you still need assistance or parts, please refer to your
nearest Authorised Service Centre, Customer Care, or contact us through our website
www.fisherpaykel.com.
In New Zealand if you need assistance…*
Call your Fisher & Paykel retailer who is trained to provide information on your
appliance, or if we can be of any further help, please contact our Customer Care Centre.
Toll Free: 0800 FP CARE or 0800 372 273
Fax: (09) 273 0656
Website: www.fisherpaykel.com
Postal address: Fisher & Paykel Appliances Ltd, PO Box 58550, Botany, Auckland 2163
If you need service…*
Fisher & Paykel has a network of independent Fisher & Paykel Authorised Repairers
whose fully trained technicians can carry out any service necessary on your appliance.
Your dealer or our Customer Care Centre can recommend a Fisher & Paykel Authorised
Repairer in your area.
In Australia if you need assistance…*
Call the Fisher & Paykel Customer Care Centre and talk to one of our Customer Care
Consultants.
Toll Free: 1300 650 590
Fax: (07) 3826 9298
Website: www.fisherpaykel.com
Postal address: Fisher & Paykel Appliances Ltd, PO Box 798, Cleveland QLD 4163
If you need service…*
Fisher & Paykel has a network of Fisher & Paykel trained and supported service
technicians responsible for servicing only Fisher & Paykel branded appliances. Our
Customer Care Centre can recommend a Fisher & Paykel trained and supported service
technician in your area.
*If you call, write or contact our website please provide: your name and address, model
number, serial number, date of purchase and a complete description of the problem.
This information is needed in order to better respond to your request for assistance.
Product details can be found under the aluminium filter.
Registration
Register your product with us so we can provide you with the best service possible.
To register your product visit our website: www.fisherpaykel.com
16
CUSTOMER CARE
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer
Suburb
Town
Country
17
© Fisher & Paykel Appliances 2015. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.
NZ AU
104032 A
10.15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement