Gasmate | GMF200G | Gasmate GMF200G User Manual

Gasmate GMF200G User Manual
200L DUAL ZONE
PREMIUM BAR FRIDGE
GMF200
A stylish and functional addition to
your outdoor space
Beer section temperature 2ºC - 5ºC
Red wine section temperature 8ºC - 18ºC
Twin fan airflow between beer and red
wine section
Stainless steel exterior
Triple glazed glass doors
Designed for outdoor undercover use
- IPx4 rated
Gasmate® is a registered trademark of:
Front vents allow installation in outdoor cabinetry with minimal clearances
Adjustable thermostat for temperature control
Self closing doors with magnetic door seal
Heated door reduces condensation
Internal lights
Adjustable shelves and racks
Height adjustable feet
Size: L90 x W50 x H85cm
Sitro Group Australia Pty Ltd
Aber – Hamilton, N.Z.
www.gasmate.com.au
www.gasmate.co.nz
Important: Retain these instructions for future use
03294 09/15
Retain manual for future reference
Product description
Inspect contents of the box to ensure all parts are included and undamaged
5
1
4
3
6
7
8
2
1.
Triple glazed glass doors
2.
Adjustable digital controller for wine side includes light switch
3.
Adjustable beer shelves
4.
Light is located at the top front of general dual zone bar fridge cabinet
5.
Blue light switch is located at top front of wine side
6.
Red wine shelves
7.
Adjustable feet
8.
Adjustable digital controller for general beverage side includes light switch
2
Installation, Operation and
Maintenance Instructions
Safe Operation
Beware of Children and Pets
Children should not be allowed to touch or operate dual
zone bar fridges or touch extension cords, if used. All
dual zone bar fridges should be kept out of reach of
children, preferably stored or locked in a secure room
when not in use.
Electrical Installation
The electrical system of this dual zone bar fridge must be
connected with an automatic 30mA circuit breaker and/or
residual current device (RCD). If uncertain have a qualified
electrician check your electrical system before installation
and/or use.
Do Not Abuse the Power Cord
Never yank or pull on the power cord to disconnect it from
the mains supply socket. Never carry or move your dual
zone bar fridge by it’s power cord. Keep the power cord
away from heat, oil, solvents and sharp edges. Check the
power cord regularly for any damage and if the power
cord becomes damaged have it replaced by an authorised
service facility.
Safety
Before attempting to operate this dual zone bar fridge,
the following basic safety precautions should be taken
to reduce the risk of fire, electric shock and personal
injury. It is important to read the instruction manual
and to understand it’s applications, limitations and
potential hazards associated with this dual zone bar
fridge. This dual zone bar fridge is not intended for use
by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning the use of the appliance by a
person responsible for their safety. This dual zone bar
fridge is not designed for use within 1m or above a water
source. It is important that you read, understand and
follow these instructions very carefully. They are designed
for the safety of yourself and others ensuring a long and
trouble free service life from your dual zone bar fridge.
This electric dual zone bar fridge complies with Australian
and International standards and safety requirements.
Repairs should only be carried out by qualified persons
using original spare parts. Failure to do so may result in
considerable danger to the operator.
Extension Cords and Reels
This dual zone bar fridge is NOT designed to run off an
extension cord. If you require an additional power point
please have one installed by a qualified electrician.
The use of extension cords may cause power voltage loss
which will result in damage to the compressor this will
NOT be covered under warranty.
For your safety
NOTE: If using the dual zone bar fridge outside in an alfresco area ensure that it is directly connected to an
outdoors power point.
Although this dual zone bar fridge is suitable for outdoor use ensure it is not left in the weather or in direct
sunlight.
The electrical system of this dual zone bar fridge must be connected with an automatic 30mA circuit breaker
and/or residual current device (RCD). If uncertain have a qualified electrician check your electrical system before
installation and/or use.
All electrical connections are to be made in a dry area.
Outdoor power points must be weatherproof and installed by a qualified electrician.
Sitro Group Australia Pty Ltd is not responsible for incorrectly located dual zone bar fridges.
3
Specific Safety Instructions
WARNING
Do not use the dual zone bar fridge in areas where
there is a risk of explosion or fire from flammable
gases. Ensure that the area is kept clear of combustible
materials. Do not use the dual zone bar fridge in damp
areas, without suitable ventilation. This dual zone bar
fridge is not designed for use within 1m or above a water
source. Do not place within one metre (1m) of any water
source.
• NEVER use with the power cord coiled, bundled up
or tied up. Always extend fully before use.
Fire risk exists if this dual zone bar fridge is
covered by or positioned close to curtains or other
combustible materials.
• Always turn the dual zone bar fridge OFF at the
power point switch when not in use for extended periods of time.
• This dual zone bar fridge is intended for
domestic/household use only.
• Always ensure that the power cord is fully extended.
• NEVER use the dual zone bar fridge if any part of
it is damaged.
• Ensure that the dual zone bar fridge is disconnected
from the mains supply when installing, cleaning or removing.
• Always ensure that the dual zone bar fridge is kept
clean and free from dust.
• DO NOT use this dual zone bar fridge in either the
bathroom or ensuite.
• Never use dual zone bar fridge with cracked/broken
glass - replace glass before use.
• DO NOT use a 3rd party timer, or programmable
system with this dual zone bar fridge.
• Only use this dual zone bar fridge on flat and
level ground.
• DO NOT clean the dual zone bar fridge while the
dual zone bar fridge is on or plugged into the
mains power supply.
• Before you throw away your old dual zone bar fridge,
take off the door, leave the shelves in place, so that
children may not easily climb inside.
• DO NOT attempt to modify the dual zone bar
fridge, power cord, power plug or the supplied
accessories in any way.
• Never allow children to operate, play with or crawl
inside the appliance.
• DO NOT expose the dual zone bar fridge to rain,
water, or use in damp wet conditions.
• This dual zone bar fridge is not designed for
perishable foods. It is a drinks dual zone bar fridge.
• DO NOT expose the dual zone bar fridge to direct
sunlight.
• Adults and children should never sit or stand on the
dual zone bar fridge as injury may occur.
• If left in direct sunlight the dual zone bar fridge
may not operate as designed.
4
Protect from Moisture
Avoiding placing the dual zone bar fridge in a place where
heavy moisture is present so as to minimise possibility
of rusting of metal parts. The dual zone bar fridge should
be kept out of water or direct sprayed water, failure to do
this could cause poor performance and/or an electrical
short could occur. Choose a location that is not affected
by rain.
WARNING
• When you dispose of your old dual zone
bar fridges and freezers, remove any doors.
Children can suffocate if they get trapped
inside.
• This appliance contains insulation formed with
flammable blowing gases. Avoid safety hazards
by carefully disposing of this appliance.
Protect from Heat
The dual zone bar fridge should be protected from
excessive heat sources and out of direct sunlight.
• The appliance must be plugged into its own
dedicated 220-240V, 50Hz AC electrical outlet.
Protect from Cold
• Ensure that the electric outlet is properly
earthed to ground. Consult a qualified
electrician if you are unsure.
The dual zone bar fridge should be protected from
excessive cold weather and frosts. Suggested minimum
ambient temperature should ideally be higher than 8°C.
• The electrical system of this dual zone bar fridge
must be connected with an automatic 30mA
circuit breaker and/or residual current device
(RCD). If uncertain have a qualified electrician
check your electrical system before installation
and/or use.
Moving
When moving, the dual zone bar fridge cannot be reclined
to more than 45°. Any greater angle may damage the
cooling system.
Never move the dual zone bar fridge while it is plugged in
and operating.
• Do not use an extension cord or adaptor plug.
• Unplug the appliance before cleaning.
Once you have moved the dual zone bar fridge, leave
standing in a level position for 2 hours so that the gas can
settle.
• Never unplug the appliance by pulling on the
power cord. Always grip the plug firmly, and
pull straight out of the receptacle to prevent
damaging the power cord.
Positioning
Ensure the sides, top and rear have at least 10mm
clearance to ensure adequate ventilation.
• Chose a location that is not too cold - the
ambient temperature should be above 8oC.
Never cover the bottom front grill as this is required for
correct ventilation.
• Chose a location that is not affected by direct
sunlight.
After installation the appliance should be left for 2 hours
before it is switched on in order to allow the refrigerant
to settle.
• Chose a location that is not affected by rain. • Put the appliance in a dry place, avoiding
areas of high moisture or humidity.
Disposal of Old Appliances
• Don’t put the appliance in direct sunlight.
The majority of components are recyclable, however there
are also dangerous chemicals inside. To dispose of old
dual zone bar fridges remove the doors and contact your
local council for recycling options.
• Don’t put the appliance near stoves, fires
or heaters.
• The appliance shall not be exposed to rain.
• Keep ventilation openings, in the appliance
enclosure or in the built-in structure, clear of
obstruction. Do not use mechanical devices
or other means to accelerate the defrosting
process. Do not use an electrical appliance
inside the appliance.
Electrical Installation
The electrical system of this dual zone bar fridge must be
connected with an automatic 30mA circuit breaker and/or
residual current device (RCD). If uncertain have a qualified
electrician check your electrical system before installation
and/or use.
• If power cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
hazard.
5
IMPORTANT
Electrical Data
This product is fitted with a sealed electrical connection
plug that is compatible with the dual zone bar fridge, the
mains supply for Australia and meets the requirements
of international standards. This dual zone bar fridge must
be connected to a supply voltage that is equal to that
stated on the rating label. If the mains connection plug or
power cord becomes damaged it must be replaced with
a complete assembly that is identical to the original, and
this must be replaced by an authorised service centre.
Always follow the Australian requirements for connection
to the mains supply. If in doubt always consult a qualified
electrician.
Note: Before using your dual zone bar fridge, unpack
and correctly position. Once in position leave to stand for
around 4-6 hours before turning on for the first time.
Glass Doors
These glass doors are heated to reduce the chance of
condensation building up during times of high humidity
and on very cold days.
These doors will be warm to touch. This is not a fault.
6
USING YOUR Dual zone bar
fridge
Temperature Control
• Your unit is provided with 2 digital controls. One for the
general beverage section and a separate one for the
wine section.
Note: During cold times, ambient temperature below
25°C the wine side may drop below your selected
“warm” temperature. If this occurs you may need to
turn the dual zone bar fridge off to totally off.
WINE
To Adjust Temperature Control
1. Press “SET”.
2. Press the
up and
down buttons to select the
desired temperature. Number will flash.
3. Once temperature is selected leave and allow flashing
number to become solid.
4. Allow dual zone bar fridge to cool for about 6 hours
before filling.
Note: The two digital controllers work separately.
Turning Off Dual zone bar fridge
To turn off your dual zone bar fridge you will need to turn
the power off at the power point and remove the power
plug.
Internal Light
To turn lights on press
button once.
To turn lights off press
button again.
The lights in each section are operated separately by the
digital controller under the specific door.
Note: The light in the wine section is coloured blue so as
to not damage the wine.
Note: If mains power is tuned off the lights default setting
is off.
To Replace Light
Note: Ensure dual zone bar fridge is turned off and the
power lead disconnected from the power point.
1. Dual zone bar fridge off and unplugged.
2. Remove screws and clear plastic cover.
3. Twist fluorescent tube out of holder.
4. Fit new fluorescent tube.
5. Fit clear plastic cover using screws, tighten.
6. Turn dual zone bar fridge on.
7
BEVERAGE
STABILISING FEET
LOCKING NUT
These are already fitted to your dual zone bar fridge.
Before turning your dual zone bar fridge on please ensure
your dual zone bar fridge is level front to back and side
to side.
1. If your dual zone bar fridge is not level use the fitted
stabilising feet to level.
2. To level unscrew the low corner stabilising bolt out until
dual zone bar fridge is level.
3. Once level lock the stabilising foot by screwing the
locking nut up to the underside of the dual zone bar
fridge body.
STABILISING FOOT
USING STABILISING FEET WITH:
Platinum II BBQ Series Marble Top
(top sold separately)
1.
Place Platinum Marble Top onto dual zone bar fridge
as per top instructions.
2.
If the overall combined unit is too low unscrew each
of the 4 stabilising feet so that the combined unit is
the same height as the BBQ and modules.
3.
Check combined unit is level.
4.
If your dual zone bar fridge is not level, use the fitted
stabilising feet to level.
5.
To level unscrew the low corner stabilising feet out
until dual zone bar fridge is level.
6.
Once level lock the stabilising feet by screwing the
locking nut up to the underside of the dual zone bar
fridge body.
8
MAINTENANCE
TROUBLE SHOOTING
• The dual zone bar fridge should be cleaned and
maintained regularly with a soft clean cloth.
1. If the dual zone bar fridge does not work:
Check if there is a power failure.
• When performing maintenance, make absolutely
sure that the power plug is first disconnected from the
power outlet.
Check if the power plug is plugged into the power outlet.
Check that the R.C.D. has not been tripped.
If ambient temperature is above 40ºC the Thermal
Safety Cut may have operated. Check if unit has
restarted once ambient temperature is below 25ºC.
• Wipe the inner and outer surface of the
dual zone bar fridge and its accessories with soft clean
wet cloth. If they are too dirty, scrub them with neutral
detergent, and then clean them with water and
dry them with a clean cloth.
2. If the dual zone bar fridge is cooling excessively:
The temperature control dial may be set too high. If you
place drinks containing a lot of water directly under the
cool air outlets they may freeze. This does not indicate
a malfunction.
• Never use hot water, petrol, alcohol, kerosene,
abrasive powder, alkaline detergent, acid, oven
cleaners, etc. These could damage the lacquer
finish and plastics.
3. If the dual zone bar fridge is not cooling sufficiently:
The drinks may be packed too tightly together which
will block the flow of cool air. You may have put
something hot or a lot of drinks into the dual zone bar
fridge. The door may not have closed properly. There
may be insufficient clearance between the dual zone
bar fridge and the other surfaces, both sides, back and
above. The temperature control dial may not be set low
enough.
• If the plastic parts in dual zone bar fridge become
contaminated by oil (animal or vegetable), they
could become brittle and possibly cracked.
4. If condensation forms on the outside of the dual
zone bar fridge:
Small amount of condensation may form on the outside
when the humidity is high. It does not indicate a
malfunction. Wipe dry with a cloth.
5. If you hear a sound like water flowing:
A sound like water flowing is the refrigerant flowing. It
does not indicate a malfunction.
6. If the cabinets side and front panel heats up:
The front and side panel of the cabinet will heat up
when the door is opened and closed frequently, when
starting the unit and when the unit operates in summer
with high ambient outside temperature. Do not touch
the front or side panel, it is a result of heat from inside
the cabinet. It does not indicate a malfunction.
CAUTION
• Never lick icy drinks when they first come out of the dual zone bar fridge.
This can freeze burn your lips and mouth.
• If the supply cord is damaged, it must be replaced by professional electrician. The cord must be replaced with
a cord of the same specification.
• Before you throw away your old dual zone bar fridge, take off the door, leave the shelves in place, so that
children may not easily climb inside.
• Never allow children to operate, play with or crawl inside the appliance.
• This dual zone bar fridge is not designed for perishable foods. It is a drinks dual zone bar fridge.
9
TECHNICAL SPECIFICATIONS
Specifications are subject to change without prior
notice.
If the technical specifications are different from
the plate on the back of the dual zone bar
fridge, please refer to the plate.
Model
GMF200
Doors
2
Capacity
200L
Rated Voltage
220 ~ 240V AC
Rated Frequency
50Hz
Rated Current
1.35A
Rated Input Power at 240V AC
230W
Energy Consumption
2.23 kW.h/24h
Light
3W + 3W
Lamp Type (x2)
T5
Noise Level (db@3m)
52 db
Refrigerant
R134a
Refrigerant Charge Volume
100gm
Foam Blowing Agent Insulation
Cyclopentane
Nett Weight
52.5kg
10
GASMATE Dual zone bar fridge PRODUCT RANGE - WARRANTY STATEMENT
Mt Waverley, Victoria, 3149 or to one of our Authorised
Service Agents.
SITRO GROUP AUSTRALIA (S.G.A.) warrants
the purchaser of this product against
defects in workmanship and materials for
the following periods from the date of
purchase:
If a warranty fault is found the freight cost will be credited to
the owner. If no fault is found the product will be returned
and any costs associated with the service will be charged to
the owner.
For domestic use, this table applies: Dual Zone Bar Fridge
Body Stainless Steel
1 Year
(surface rust excluded)
Dual Zone Bar Fridge
Body Powder Coated
1 Year
(surface rust excluded)
Compressor
1 Year
All Other Items
1 Year
Products sent freight forward will not be accepted. In most
cases the defective accessory or component only will need
to be returned. The product or part of the product being
returned must be adequately protected in a box.
S.G.A. will not be responsible for any in-transit loss or
damage.
This warranty does not apply to any defect, deterioration,
loss, injury or damage occasioned by or as a result of misuse
or abuse, negligent handling or storage, normal wear and
tear or if the product has not been installed and used in
accordance with S.G.A.’s instructions, recommendations
and specifications or if the product has been subjected
to abnormal conditions. The warranty does not apply to
blockages caused by insects or living organisms.
For commercial use : - 3 Months
This warranty is not transferable to a subsequent purchaser
if the product is sold by the original purchaser during the
warranty period.
The warranty is void if there is evidence of the product being
tampered with by unauthorised persons.
If a warranty fault appears within the warranty period, S.G.A.
reserves the right to replace or repair the product.
The warranty does not extend to installation or disconnection
costs.
In the event that S.G.A. chooses to replace the product, this
original warranty will expire at the original date.
Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. The benefits of this
warranty are in addition to any rights and remedies imposed
by Australian State and Federal legislation that cannot be
excluded.
If the product includes various accessories or components,
only the defective accessory or component will be replaced
or repaired.
S.G.A. reserves the right to replace defective parts of the
product with parts and components of similar quality, grade
and composition where an identical part or component is not
available.
Products presented for repair may be replaced by
refurbished products of the same type rather than being
repaired. Refurbished parts may be used to repair the
products.
Electric Products Approved For Outdoor Use Only
For warranty claims, service, spare parts or products
information in Australia, please call SITRO GROUP
AUSTRALIA Pty Ltd on the Customer Service Line 1300
174 876
To make a warranty claim, first contact S.G.A’s Customer
Service Line on the contact number below.
Register your Warranty online at
www.gasmate.com.au
A receipt or proof of purchase is required and must be kept
for your records.
Note: If you do not have internet access call our customer
service team on 1300 174 876
The purchase receipt for this product is to be retained and
must be presented if making claim under the terms of this
S.G.A. warranty.
Warranty repairs are free of charge, provided the product is
delivered to our Service Department at 33-35 Lionel Road,
CONTACT DETAILS
Sitro Group Australia Pty Ltd
33-35 Lionel Road, Mt. Waverley
Victoria 3149, Australia.
Tel (+613) 9543 9533
Fax (+613) 9543 9839
sales@sitro.com.au
11
For any queries or assistance call
Customer Service
(Australia Only)
1300 174 876
Hours of operation:
Monday to Friday 8.30am - 5.30pm EST
Do not return to place of purchase.
Keep your purchase receipt, this will be required to
make any claims under the 12 month warranty.
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising