LG | ARNU12GTSA4 | Installation guide | LG ARNU18GTSA4.ANWBASE Installation guide

LG ARNU18GTSA4.ANWBASE Installation guide
ENGLISH
BAHASA INDONESIA
INSTALLATION MANUAL
AIR
CONDITIONER
Please read this installation manual completely before installing the product.
Installation work must be performed in accordance with the national wiring
standards by authorized personnel only.
Please retain this installation manual for future reference after reading it thoroughly.
Ceiling Cassette – 2Way
ARNU09GTSA4 ARNU12GTSA4 ARNU18GTSA4 ARNU24GTSA4
Original instruction
MFL68686533
Rev.00_040519
www.lg.com
Copyright © 2018 - 2019 LG Electronics Inc. All Rights Reserved.
Table of contents
TABLE OF CONTENTS
3
INSTALLATION PARTS
4
SAFETY PRECAUTIONS
6
INSTALLATION
6
Model Designation
6
Airborne Noise Emission
6
Limiting concentration
7
Selection of the best location
8
Ceiling dimension and hanging bolt location
9
Wiring Connection
10
Installation of Decoration Panel
11
Drain Piping
13
DIP Switch Setting
14
Group Control Setting
2
Indoor Unit
Installation Parts
ENGLISH
Installation Parts
Air filter
Air Intake
Air Outlet
Wired Remote Controller
(Optional)
Installation Tool
Name
Quantity
Drain hose Clamp metal
1 EA
2 EA
Washer for
hanging bracket
8 set
Clamp
(Tie Wrap)
4 EA
Shape
Insulation for
fitting
1 EA
for gas pipe
(Other)
• Paper pattern for
installation
• Owner's manual
• Installation
manual
for liquid pipe
• Screws for fixing panels are attached to decoration panel.
Installation Manual 3
Safety Precautions
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions must be
followed.
n Be sure to read before installing the air conditioner.
n Be sure to observe the cautions specified here as they include important items related to safety.
n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is
classified by the following indications.
!
!
WARNING This symbol indicates the possibility of death or serious injury.
CAUTION This symbol indicates the possibility of injury or damage to properties only.
n Meanings of symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
!
WARNING
Installation
• Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated
circuit.
- There is risk of fire or electric shock.
• For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized
Service Center.
- Do not disassemble or repair the product. There is risk of fire or electric shock.
• Always ground the product.
- There is risk of fire or electric shock.
• Install the panel and the cover of control box securely.
- There is risk of fire or electric shock.
• Always install a dedicated circuit and breaker.
- Improper wiring or installation may cause fire or electric shock.
• Use the correctly rated breaker or fuse.
- There is risk of fire or electric shock.
• Do not modify or extend the power cable.
- There is risk of fire or electric shock.
• Do not let the air conditioner run for a long time when the humidity is very high and a door
or a window is left open.
- Moisture may condense and wet or damage furniture.
• Be cautious when unpacking and installing the product.
- Sharp edges could cause injury. Be especially careful of the case edges and the fins on
the condenser and evaporator.
• For installation, always contact the dealer or an Authorized Service Center.
- There is risk of fire, electric shock, explosion, or injury.
• Do not install the product on a defective installation stand.
- It may cause injury, accident, or damage to the product.
4
Indoor Unit
Safety Precautions
Operation
• Do not store or use flammable gas or combustibles near the product.
- There is risk of fire or failure of product.
!
CAUTION
Installation
• Always check for gas (refrigerant) leakage after installation or repair of product.
- Low refrigerant levels may cause failure of product.
• Install the drain hose to ensure that water is drained away properly.
- A bad connection may cause water leakage.
• Keep level even when installing the product.
- To avoid vibration or water leakage.
• Use two or more people to lift and transport the product.
- Avoid personal injury.
• In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance
must not be supplied through an external switching device, such as a timer, or connected to
a circuit that is regularly switched on and off by the utility.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazrd.
• This equipment shall be provided with a supply conductor complying with the national
regulation.
• Means for disconnection must be incorporated in the fixed wiring in accordance with the
wiring rules.
Installation Manual 5
ENGLISH
• Be sure the installation area does not deteriorate with age.
- If the base collapses, the air conditioner could fall with it, causing property damage,
product failure, and personal injury.
• Use a vacuum pump or inert (nitrogen) gas when doing leakage test or air purge. Do not
compress air or oxygen, and do not use flammable gases. Otherwise, it may cause fire or
explosion.
- There is the risk of death, injury, fire or explosion.
• Do not turn on the breaker or power under condition that front panel, cabinet, top cover,
control box cover are removed or opened.
- Otherwise, it may cause fire, electric shock, explosion or death.
Installation
Installation
Read completely, then follow step by step.
Model Designation
ARN
U
24
G
TS
A
4
Serial Number
Combinations of functions
A:Basic function
C: Ionizer(Ceiling Cassette) : Optional
Chassis Name
Electrical Ratings
3:1 Ø, 208/230 V, 60 Hz
G:1 Ø, 220 - 240 V, 50 Hz/1 Ø, 220 V, 60 Hz
(Only 50 Hz for Australia)
Total Cooling Capacity in Btu/h
EX) 5 000 Btu/h ➝ '05'
18 000 Btu/h ➝ '18'
Combination of Inverter Type and
Cooling Only or Heat Pump
N: AC Inverter and H/P V: AC Inverter and C/O
U: DC Inverter and H/P and C/O
System with Indoor Unit using R410A
❈ LGETA:U Ex) URN
Airborne Noise Emission
The A-weighted sound pressure emitted by this product is below 70 dB.
** The noise level can vary depending on the site.
The figures quoted are emission level and are not necessarily safe working levels. Whilst there is a
correlation between the emission and exposure levels, this cannot be used reliably to determine
whether or not further precautions are required. Factor that influence the actual level of exposure of the
workforce include the characteristics of the work room and the other sources of noise, i.e. the number
of equipment and other adjacent processes and the length of time for which an operator exposed to the
noise. Also, the permissible exposure level can vary from country to country. This information, however,
will enable the user of the equipment to make a better evaluation of the hazard and risk.
Limiting concentration
Limiting concentration is the limit of Freon gas concentration where immediate measures can be
taken without hurting human body when refrigerant leaks in the air. The limiting concentration shall
be described in the unit of kg/m3 (Freon gas weight per unit air volume) for facilitating calculation
Limiting concentration: 0.44 kg/m3 (R410A)
n Calculate refrigerant concentration
Total amount of replenished refrigerant in refrigerant facility (kg)
Refrigerant concentration =
Capacity of smallest room where indoor unit is installed (m3)
6
Indoor Unit
Installation
21±3
Above 1 800
3 000 or less
500 or
more
1 000
or more
Ceiling
Ceiling Board
Ceiling Board
500 or
more
300 or less
300 or more
• There should not be any heat source or steam near the unit.
• There should not be any obstacles to the air circulation.
• A place where air circulation in the room will be good.
• A place where drainage can be easily obtained.
• A place where noise prevention is taken into consideration.
• Do not install the unit near the door way.
• Ensure the spaces indicated by arrows from the wall, ceiling, or other obstacles.
• The indoor unit must have the maintenance space.
Unit:mm
Floor
!
CAUTION
In case that the unit is installed near the sea, the installation parts may be corroded by
salt. The installation parts (and the unit) should be taken appropriate anti-corrosion
measures.
Installation Manual 7
ENGLISH
Selection of the best location
Installation
Ceiling dimension and hanging bolt location
• The dimensions of the paper model for installation are the same as those of the ceiling
opening dimensions.
1 033 (Ceiling opening)
855 (Hanging bolt)
Ceiling
60
830
!
CAUTION
• This air-conditioner uses a drain pump.
• Install the unit horizontally using a level
gauge.
• During the installation, care should be taken
not to damage electric wires.
• Select and mark the position for fixing bolts
and piping hole.
• Decide the position for fixing bolts slightly
tilted to the drain direction after considering
the direction of drain hose.
• Drill the hole for anchor bolt on the wall.
642 (Ceiling opening)
600
410(Hanging bolt)
116
Level gauge
unit: mm
Ceiling board
NOTICE
• Avoid the following installation location.
1. Such places as restaurants and kitchen where considerable amount of oil steam and flour is
generated.
These may cause heat exchange efficiency reduction, or water drops, drain pump mal-function.
In these cases, take the following actions;
• Make sure that ventilation fan is enough to cover all noxious gases from this place.
• Ensure enough distance from the cooking room to install the air conditioner in such a place
where it may not suck oily steam.
2. Avoid installng air conditioner in such
places where cooking oil or iron
Air conditioner
powder is generated.
3. Avoid places where inflammable gas
Take enough
is generated.
distance
Use the ventilation fan
4. Avoid places where noxious gas is
for smoke-collecting
hood with sufficient
generated.
capacity.
Cooking table
5. Avoid places near high frequency
generators.
8
Indoor Unit
Installation
90 mm
Nut
(W3/8 or M10)
Flat washer for M10
(accessory)
Ceiling board
Air Conditioner body
Flat washer for M10
(accessory)
Nut
(W3/8 or M10)
Paper pattern
for installation
Set screw of
paper pattern (4 pieces)
Open the ceiling board
along the outer edge of the
paper pattern
Adjust the
same height
• The following parts are local purchasing.
① Hanging Bolt - W 3/8 or M10
② Nut
- W 3/8 or M10
③ Spring Washer - M10
④ Plate Washer - M10
!
Ceiling board
CAUTION
Tighten the nut and bolt to prevent the
unit from falling.
Wiring Connection
Connect the wires to the terminals on the control board individually according to the outdoor unit connection.
• Ensure that the color of the wires of outdoor unit and the terminal No. are the same as those of indoor unit
respectively.
Terminal Block
Indoor
1(L) 2(N)
Terminal
Block
Indoor
3
4
Terminal Block of outdoor unit
SODU
B
A
IDU
B
A
INTERNET DRY1 DRY2 GND 12 V Outdoor unit
B
A
-
INDOOR POWER INPUT
!
WARNING
Make sure that the screws of the terminal are free from looseness.
!
CAUTION
The Power cord connected to the unit should be selected according to the following
specifications.
!
CAUTION
The connecting cable connected to the indoor and outdoor unit should be complied with the
following specifications (This equipment shall be provided with a cable set complying with the
national regulation).
If the supply cable is damaged, it must be replaced by a special cable or assembly available from
the manufacturer of its service agent.
Installation Manual 9
ENGLISH
Ceiling
Keep the length of the bolt
from the bracket to 40 mm
Hanging bolt
(W3/8 or M10)
Installation
Installation of Decoration Panel
The decoration panel has its
installation direction.
Before installing the decoration panel,
always remove the paper template.
1. Temporarily fix two decoration panel fixing screws (hexagon M5 screw) on the unit body.
(Tighten by amount 10 mm in length.) The fixing screws (hexagon M5 screw) are
included the indoor unit box.
2. Remove the air inlet grille from the decoration panel. (Remove the hook for the air inlet grille cord.)
3. Hook the decoration panel key hole (
) on the screws fixed in step above, and slide
the panel so that the screws reach the key hole edge.
4. Retighten completely two temporarily fixed screws and other two screws. (Total 4 screws)
5. Connect the louver motor connector and display connector.
6. After tightening these screws, install the air inlet grille (including the air filter).
Air conditioner unit
Piping side
Control box cover
Decorative panel
Display
Louver motor
Lead wire for louver motor
and display
Decorative panel
fixing screws
(Hexagon M4 screw)
Decorative panel fixing screws
(hexagon M5 screws)
Temporary fitting at 2 poles
(Tightening about 10 mm)
Inlet Grille
!
CAUTION
Install certainly the
decoration panel.
Cool air leakage
causes sweating.
⇨ Water drops fall.
10
Indoor Unit
Good example
Bad example
Air conditioner
unit
Cool air leakage
(no good)
Ceiling
board
Decoration panel
Fit the insulator (this part) and
be careful for cool air leakage
Air conditioner
unit
Ceiling
board
Decoration panel
Installation
• Drain piping must have down-slope (1/50 to
1/100): be sure not to provide up-and-down slope
to prevent reversal flow.
• During drain piping connection, be careful not to
exert extra force on the drain port on the indoor
unit.
• The outside diameter of the drain connection on
the indoor unit is 32 mm.
Upward
routing
not allowed
Pipe clamp
Indoor unit
Maintenance
drain port
Piping material: Polyvinyl chloride pipe VP-25
and pipe fittings
1/50~1/100
• Be sure to install heat insulation on the drain
piping.
MAX 700 mm
Heat insulation material: Polyethylene foam
with thickness more than 8 mm.
Drain test
The air conditioner uses a drain pump to drain water.
Use the following procedure to test the drain pump operation:
Feed water
Flexible drain hose
(accessory)
Main
drain pipe
Drain Pump
Drain
port
Glue the joint
Drain hose connection
Use the clip (accessory)
Drain pan
• Connect the main drain pipe to the
exterior and leave it provisionally until
the test comes to an end.
• Feed water to the flexible drain hose
and check the piping for leakage.
• Be sure to check the drain pump for
normal operating and noise when
electrical wiring is complete.
• When the test is complete, connect the
flexible drain hose to the drain port on
the indoor unit.
Flexible drain hose
CAUTION
The supplied flexible drain hose should
not be curved, neither screwed. The
curved or screwed hose may cause a
leakage of water.
Hanger
Max 300 mm distance
1~15 m
Hanger Bracket
1/50~1/100 slope
Metal
Flexible drain hose
clamp
Flexible drain hose
Max 700 mm
!
Insulation
Installation Manual 11
ENGLISH
Drain Piping
Installation
!
CAUTION
Be sure to test the power line and communication line for incorrect wiring before power is
applied.
1) If the power line and communication line are swapped over, the product will be
damaged.
2) Incorrect wiring confirmation test method
: Measure the resistance across the power terminals (L, N) using a multi meter.
- Resistance value of a normal connection: 1 MΩ or more
- Incorrect wiring resistance value: 500 kΩ or less.
!
CAUTION
After the confirmation of the above conditions, prepare the wiring as follows:
1) Never fail to have separate power specially for the air conditioner. As for the method of
wiring, follow the circuit diagram pasted on the inside of control box cover.
2) Provide a circuit breaker switch between power source and the unit.
3) The screw which fasten the wiring in the casing of electrical fittings are liable to come
loose from vibrations to which the unit is subjected during the course of transportation.
Check them and make sure that they are all tightly fastened. (If they are loose, it could
give rise to burn-out of the wires.)
4) Confirm the Specification of power source
5) Confirm that electrical capacity is sufficient.
6) Be sure that the starting voltage is maintained at more than 90 % of the rated voltage
marked on the name plate.
7) Confirm that the cable thickness is as specified in the power sources specification.
(Particularly note the relation between cable length and thickness.)
8) Do not install the leakage breaker in a place which is wet or moist.
Water or moist may cause short circuit.
9) The following troubles would be caused by voltage drop-down.
• Vibration of a magnetic switch, damage on the contact point there of, fuse breaking,
disturbance to the normal function of a overload protection device.
• Proper starting power is not given to the compressor.
10) Before applying power to the indoor unit, be sure to check for incorrect wiring of the
power and communication lines.
HAND OVER
Teach the customer the operation and maintenance procedures, using the operation manual.
(air filter cleaning, temperature control, etc.)
12
Indoor Unit
Installation
ENGLISH
DIP Switch Setting
1. Indoor Unit
SW1
SW2
Function
Communication
Cycle
SW3
Group Control
SW4
Dry Contact
Mode
SW5
Installation
SW6
Heater linkage
SW7
SW8
!
Description
N/A (Default)
N/A (Default)
Setting Off
-
Selection of Master or
Slave
Master
Selection of Dry
Contact Mode
Fan continuous
operation
N/A
Setting On Default
Off
Off
Wired/Wireless remote
controller selection of
Manual or Auto
operation Mode
Continuous operation
Removal
-
Slave
Off
Auto
Off
-
Off
-
Off
Ventilator
linkage
Selection of Ventilator
linkage
Vane selection
(Console)
Selection of up/down
Up side Vane
Up side + Down side Vane
side Vane
Only
Region
selection
Etc.
Selection tropical
region
Spare
Linkage Removal
Working
Tropical
model
-
General model
-
Off
Off
CAUTION
For Multi V Models, DIP switch 1, 2, 6, 8 must be set OFF.
2. Outdoor Unit
In case that the products meet specific conditions, “Auto addressing” function can start automatically
with the improved speed by turning the DIP switch #3 of the outdoor unit and resetting the power.
* Specific conditions:
- All names of the indoor units are ARNU****4.
- The serial number of Multi V super IV (outdoor units) is after October 2013.
DIP switch
7 segment
Outdoor Unit PCB
Outdoor Unit DIP Switch
Installation Manual 13
Installation
Group Control Setting
1. Group Control 1
n Wired remote controller 1 + Standard Indoor Units
LGAP Network System
or
Master
Slave
Slave
GND
Signal
12 V
Only connect serial signal and
GND lines between indoor units.
Display Error Message
°C / °F (5 s)
Slave
Master
TIME (3 s)
n DIP Switch in PCB
¿ Master Setting
- No. 3 Off
¡ Slave Setting
- No. 3 On
Indoor Unit DIP Switch
Some products have no DIP switch on PCB. It is possible to set indoor units to Master or Slave by
using the wireless remote controller instead of DIP switch.
For the details of the setting, please refer to the manual of the wireless remote controller.
1. It is possible to 16 indoor units(Max.) by one wired remote controller.
Set only one indoor unit to Master, set the others to Slave.
2. It is possible to connect with every type of indoor units.
3. It is possible to use wireless remote controller at the same time.
4. It is possible to connect with Dry Contact and Central controller at the same time.
- The Master indoor unit is possible to recognize Dry Contact and Central Controller only.
5. In case that any error occurs at indoor unit, the error code is displayed on the wired remote
controller.
It is possible to control the other indoor units except the error units.
14
Indoor Unit
Installation
ENGLISH
h It is possible to connect indoor units since Feb. 2009.
h It can be the cause of malfuctions when there is no setting of master and slave.
h In case of Group Control, it is possible to use following functions.
- Selection of operation, stop or mode
- Temperature setting and room temperature check
- Current time change
- Control of flow rate (High/Middle/Low)
- Reservation settings
It is not possible to use some functions.
2. Group Control 2
n Wired remote controllers + Standard Indoor Units
LGAP Network System
or
Master
Master
Slave
Slave
GND
Signal
12 V
Donʼt connect serial 12 V line
Display Error Message
°C / °F (5 s)
TIME (3 s)
Master
Master
h It is possible to control 16 indoor units(Max.) with the master wired remote control.
h Other than those, it is same with the Group Control 1.
Installation Manual 15
Installation
3. Group Control 3
n Mixture connection with indoor units and Fresh Air Intake Unit
LGAP Network System
or
FAU
Master
FAU
Slave
Master
GND
Signal
12 V
Slave
N
M
Display Error Message
Display Error Message
°C / °F (5 s)
TIME (3 s)
Master
Master
h In case of connecting with standard indoor unit and Fresh Air Intake Unit, separate Fresh
Air Intake Unit with standard units. (N, M ≤ 16) (Because setting temperature are different.)
h Other than those, it is same with Group Control 1.
FAU
FAU
Standard
Standard
FAU
FAU
Standard
Standard
* FAU : Fresh Air Intake Unit
Standard: Standard Indoor Unit
16
Indoor Unit
Installation
ENGLISH
4. 2 Remote Control
n Wired remote controller 2 + Indoor unit 1
LGAP Network System
or
Slave
Master
Slave
Slave
GND
Signal
12 V
Display Error Message
°C / °F (5 s)
TIME (3 s)
Master
Slave
1. It is possible to connect two wired remote controllers (Max.) with one indoor unit.
Set only one indoor unit to Master, set the others to Slave.
Set only one wired remote controller to Master, set the others to Slave.
2. Every types of indoor unit is possible to connect two remote controller.
3. It is possible to use wireless remote controller at the same time.
4. It is possible to connect with Dry Contact and Central controller at the same time.
5. In case that any error occurs at indoor unit, the error code is displayed on the wired
remote controller.
6. There isnʼt limits of indoor unit function.
Installation Manual 17
Installation
5. Accessories for group control setting
It is possible to set group control by using below accessories.
Indoor unit 2 EA +Wired remote controller 1 EA Indoor unit 1 EA +Wired remote controller 2 EA
h PZCWRCG3 cable used for connection
h PZCWRC2 cable used for connection
Slave
Master
PZCWRC2
PZCWRCG3
Master
!
Master
Slave
CAUTION
• Apply totally enclosed noncombustible conduit in case of local building code Requiring
plenum cable usage.
18
Indoor Unit
PT.LG Electronics Indonesia
Gandaria 8 Office Tower Lt. 29 BC & 31 ABCD
Jl.Sultan Iskandar Muda, Kebayoran Lama Utara - Kebayoran Lama,
Jakarta Selatan - DKI Jakarta Raya, Indonesia
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising