LG | 50PA4500 | Owner's Manual | LG 50PA4500 Owner's Manual

LG 50PA4500 Owner's Manual
OWNER’S MANUAL
PLASMA TV
Please read this manual carefully before operating the
set and retain it for future reference.
PA45**
PA49**
PA65**
P/NO : MFL67230031 (1205-REV05)
Printed in Korea
www.lg.com
2
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
ENGLISH
ENG
Please read these safety precautions carefully before using the product.
yy
In this manual, the illustration may be somewhat different from your product because it is
yy
just example to help the instruction.
you ignore the warning message, you may be seriously injured or there is a
warning yyIf
possibility of accident or death.
caution yyIf you ignore the caution message, you may be slightly injured or the product may
be damaged.
Precaution in Installing the Product
warning
Keep away from heat sources like electrical
heaters.
- Electrical shock, fire, malfunction or
deformation may occur.
As long as this unit is connected to the AC wall outlet, it is
not disconnected from the AC power source even if you
turn off this unit by SWITCH.
Precautions when Moving the Product
warning
Do not use the product in damp place such
as a bathroom or any place where it is likely
to get wet.
- This may cause a fire or could give an
electric shock.
Make sure to turn off the product.
Make sure to remove all cables before
moving the product.
- You may be electrocuted or the product
can be damaged.
If you can smell smoke or other odours or hear
a strange sound unplug the power cord and
contact the service center.
- If you continue to use without taking proper
measures, electrical shock or fire can occur.
Do not impact the product when moving it.
- You may be electrocuted or the product
can be damaged.
CAUTION
Install the product on a flat and stable place
that has no risk of dropping the product.
- If the product is dropped, you may be injured
or the product may be broken.
Keep the product away from direct sunlight.
- The product can be damaged.
Do not place the product in a built-in
installation such as bookcase or rack.
- Ventilation required.
Electrical Power Related Precautions
warning
Make sure to connect the power cable to a
properly earthed outlet.
- You may be electrocuted or injured.
Do not touch the power plug with wet hands.
Additionally, it the cord pin is wet or covered
with dust, dry the power plug completely or wipe
dust off.
- You may be electrocuted due to excess
moisture.
Never touch this product or antenna during a
thunder or lighting storm.
- You may be electrocuted.
Do not insert a conductor (like a metal
chopstick) into one end of the power cable while
the other end is connected to the input terminal
on the wall.
Additionally, do not touch the power cable right
after plugging into the wall input terminal.
- You may be electrocuted.
CAUTION
Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits
the appliance.
CAUTION
Make the panel face forward and hold it
with both hands to move.
- If you drop the product, the damaged
product can cause electric shock or fire.
Contact your nearest service center for
repair.
Precautions when Using the Product
warning
Do not disassemble, repair or modify the
product at your own discretion.
- Fire or electric shock accident can occur.
- Contact the service center for check,
calibration or repair.
To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or
moisture.
Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases, shall be
placed on the apparatus.
efer all servicing to qualified service
R
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN /
BURN-IN” ON YOUR TELEVISION SCREEN
-W
hen a fixed image (e.g. logos, screen menus, video game,
computer display or teletext pages) is displayed on the
television for an extended period it can become permanently
imprinted on the screen. This phenomenon is known as “image
burn” or “burn-in”. Image burn is not covered under the
manufacturer’s warranty.
- In order to prevent image burn, avoid displaying a fixed
image on your television’s screen for a prolonged period (2 or
more hours for LCD, 1 or more hours for Plasma).
- Image burn can also occur on the letterboxed areas of
your television if you use the 4:3 aspect ratio setting for an
extended period.
TABLE OF CONTENTS / ADDITIONAL INFORMATION
3
2
SAFETY INSTRUCTIONS
16
3
ADDITIONAL INFORMATION
17WATCHING TV
4
Installation Procedure
17
17
Connecting an antenna
Turning the TV on for the first time
4
ASSEMBLING AND PREPARING
18
MAKING CONNECTIONS
4
7
7
10
11
11
13
14
15
Unpacking
Separate purchase
Parts and buttons
Lifting and moving the TV
Setting up the TV
- Attaching the stand
- Tidying cables
- Mounting on a table
- Mounting on a wall
18
Connecting your Unit
19
ENTERTAINMENT
19
20
- Connecting USB storage devices
- Browsing files
21
TROUBLESHOOTING
22
SPECIFICATIONS
24
Open source software notice
REMOTE CONTROL
ADDITIONAL INFORMATION
Viewing the owner’s manual
The owner’s manual in PDF file format is supplied on the enclosed CD. Install the Adobe Acrobat Reader to
view the owner’s manual on your PC.
1 Insert the supplied CD. The web page appears automatically.
2 Click Owner’s Manual on the web page.
3 View the owner’s manual.
NOTE
If the web page does not appear automatically, access My computer and then click LG and index.htm
to view the owner’s manual.
ENGLISH
ENG
TABLE OF CONTENTS
4
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
NOTE
ENGLISH
ENG
yy
Image shown may differ from your TV.
yy
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
Installation Procedure
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and item.
Only 42/50PA45**, 50/60PA65**
Remote control,
Batteries (AAA)
( See p. 16)
Screw for assembly
4 EA, M4 x 30
( See p. 11~12)
3 EA, M5 x 16
( See p. 11)
Protection Cover
( See p. 12)
Owner’s manual,
CD manual
Polishing cloth
(Depending on model)
Use this to remove dust
from the cabinet.
Power Cord Holder
( See p. 13)
Power Cord
Ferrite core
(Depending on model)
Cable Holder
( See p. 13)
or
Stand Body
( See p. 11)
Stand Base
( See p. 11)
Isolator
(Depending on model)
( See p. 7 )
ASSEMBLING AND PREPARING
5
Only 42/50PA49**
ENGLISH
ENG
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
6
7
8
9
LIST
0
FLASHBK
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
Q.MENU
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
Remote control,
Batteries (AAA)
( See p. 16)
Owner’s manual,
CD manual (Included
Pentouch Software)
Pentouch Caution Guidelines
Polishing cloth
(Depending on model)
Gently wipe the spots on the
cabinet with the polishing
cloth.
Power Cord
Protection Cover
( See p. 12)
Cable Holder
( See p. 13)
Power Cord Holder
( See p. 13)
Ferrite core
(Depending on model)
D-sub 15 pin signal cable
Eye-bolt & Wall bracket
2 EA ( See p. 14)
Cradle
Touch Pen Dongle
(AN-TD200)
Charging Cable
Tip
The number of tip may differ
depending on the model.
Touch Pen (AN-TP300)
The number of touch pen
may differ depending on the
model.
Stand Base
( See p. 11)
Screw for assembly
4 EA, M4 x 30
( See p. 11~12)
3 EA, M5 x 16
( See p. 11)
or
Isolator
(Depending on model)
( See p. 7 )
Home
Stand Body
( See p. 11)
6
ASSEMBLING AND PREPARING
Caution
ENGLISH
ENG
Do not use any pirated items to ensure the safety and product life span.
yy
Any damages or injuries by using pirated items are not covered by the manufacturer’s warranty.
yy
NOTE
The items supplied with your product may vary depending on the model and Country.
yy
Product specifications or contents of this manual may be changed without prior notice due to
yy
upgrade of product functions.
How to use the ferrite core.
yy
This feature is not available for all country.
1. Use the ferrite core to reduce the electromagnetic interference in the PC audio cable.
Wind the PC audio cable on the ferrite core thrice. Place the ferrite core close to the TV.
10 mm(+ / - 5 mm)
[to an External device]
[to the TV]
(Gray)
[Cross Section of
Ferrite Core]
[Figure 1]
2. Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV and a wall plug.
[to the TV]
[to a wall plug]
(Black)
[Cross Section of
Ferrite Core]
[Figure 2]
3. Use the ferrite core to reduce the electromagnetic interference in the component Y, Pb, Pr, L,
R cable. Place the ferrite core close to the TV.
[to the TV]
[to a wall plug]
(Black)
[Cross Section of
Ferrite Core]
10 mm(+ / - 5 mm)
[Figure 3]
- If there are three ferrite cores, follow as shown in Figures 1 and 2.
- If there are four ferrite cores, follow as shown in Figure 1, 2 and 3.
yy
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and
18 mm width. Use an extension cable that supports
USB 2.0 if the USB cable or USB memory stick does
not fit into your TV’s USB port.
*A
*B
10 mm
18 mm
ASSEMBLING AND PREPARING
7
NOTE
1. Connect to TV.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
or
Isolator
2. Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains
connection or through other equipment with a connection to protective earthing - and to a cable
distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection to
a cable distribution system has therefore to be provided through a device providing electrical isolation
below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer for buying these items.
These devices only work with compatible LG Plasma TV.
AN-TP300
Touch Pen, Cradle
The number of touch pen and
cradle may differ depending on
the model.
Compatibility
AN-TP300
Touch Pen, Cradle
42/50PA45**
42/50PA49** 50/60PA65**
•
Parts and buttons
NOTE
yy
The TV can be placed in standby mode in order to reduce the power consumption. And the TV
should be turned off if it will not be watched for some time, as this will reduce energy consumption.
yy
The energy consumed during use can be significantly reduced if the level of brightness of the
picture is reduced, and this will reduce the overall running cost.
Caution
Do not step on the glass stand or subject it to any impact. It may break, causing possible injury
yy
from fragments of glass, or the TV may fall.
Do not drag the TV. The floor or the product may be damaged.
yy
Some models have a thin film attached on to the screen and this must not be removed.
yy
ENGLISH
ENG
yy Antenna Isolator Installation Guide
-- Use this to install TV in a place where there is a voltage difference between TV Set and GND of
antenna signal.
»» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact
might be heated and excessive heat might cause an accident.
-- You can improve the safety when watching TV by efficiently removing power voltage from TV
antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall,
mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
-- Before starting, be sure that the TV antenna is connected.
8
ASSEMBLING AND PREPARING
Remote control and
intelligent1 sensors
Side Connection panel
IN 3
HDMI
/DVI
IN 2
/DVI IN 2
HDMI
IN 3
USB IN
Screen
USB IN
USB
input
Power indicator  Red – In Standby mode
 Off – TV turns on
(Only 42/50PA450*)
(Only 42/50PA452*,
42/50PA49**,
50/60PA65**)
/DVI IN 2
ENGLISH
ENG
Only 42/50PA45**-TA~F, 42/50PA49**-TA~F, 50/60PA65**-TA~F
Speakers
INPUT
SETTINGS
OK
ns
Buttons
RGB IN
(PC)
RS-232C IN
(CONTROL & SERVICE)
AUDIO IN
(RGB/DVI)
AV IN
COMPONENT
IN
VIDEO
L/MONO AUDIO R
Y
PB
PR
L
ANTENNA/
CABLE IN
R
1
VIDEO
AUDIO
1
Button
/I
INPUT
SETTINGS
IN
Description
Turns the power on or off
Changes the input source
Accesses the main menus, or saves your input and exits the menus
Selects the highlighted menu option or confirms an input
OK
1
Connection panel
OPTICAL
DIGITAL
AUDIO OUT
2
- +
Adjusts the volume level
v
Scrolls through the saved programmes
^
Intelligent sensor - Adjusts the image quality corresponding to the surrounding environment.
ASSEMBLING AND PREPARING
9
ENGLISH
ENG
Only 42/50PA45**-TG~M, 42/50PA49**-TG~M, 50/60PA65**-TG~M
Remote control and
intelligent1 sensors
Side Connection panel
HDMI
IN 3
IN 2
HDMI
IN 2
IN 2
IN 3
USB IN
Screen
USB IN
USB
input
Power indicator  Red – In Standby mode
 Off – TV turns on
(Only 42/50PA450*)
(Only 42/50PA452*,
42/50PA453*,
42/50PA49**,
50/60PA65**)
Speakers
INPUT
SETTINGS
OK
ttons
Buttons
RGB IN
(PC)
AUDIO IN
RS-232C IN
(CONTROL & SERVICE)
(RGB/DVI)
AV IN
COMPONENT
IN
VIDEO
L/MONO AUDIO R
OPTICAL
DIGITAL
AUDIO OUT
2
Y
PB
PR
L
ANTENNA/
CABLE IN
R
1
VIDEO
AUDIO
1
Button
/I
INPUT
SETTINGS
IN
/DVI
Description
Turns the power on or off
Changes the input source
Accesses the main menus, or saves your input and exits the menus
Selects the highlighted menu option or confirms an input
OK
1
Connection panel
- +
Adjusts the volume level
v
Scrolls through the saved programmes
^
Intelligent sensor - Adjusts the image quality corresponding to the surrounding environment.
10
ASSEMBLING AND PREPARING
ENGLISH
ENG
Lifting and moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged
and for safe transportation regardless of its type
and size.
When transporting a large TV, there should
yy
be at least 2 people.
When transporting the TV by hand, hold the
yy
TV as shown in the following illustration.
Caution
Avoid touching the screen at all times, as
yy
this may result in damage on the screen
or some of the pixels used to create
images.
It is recommended to move the TV in the
yy
box or packing material that the TV originally
came in.
Before moving or lifting the TV, disconnect
yy
the power cord and all cables.
When holding the TV, the screen should face
yy
away from you to prevent the screen from
scratches.
Hold the top and bottom of the TV frame
yy
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
When transporting the TV, do not expose the
yy
TV to jolts or excessive vibration.
When transporting the TV, keep the TV
yy
upright, never turn the TV on its side or tilt
towards the left or right.
ASSEMBLING AND PREPARING
11
Put your TV on a pedestal stand and mount the TV on a table or wall.
Attaching the stand
If you are not mounting the TV to a wall, use the following instructions to attach the stand.
Only 42/50PA45**, 42/50PA49**,50/60PA65**
1
2
3 EA
M5 x 16
Stand Body
Front
Caution
Stand Base
When attaching the stand to the TV
yy
set, place the screen facing down on a
cushioned table or flat surface to protect
the screen from scratches.
3
4 EA
M4 x 30
Caution
Make sure that the screws are inserted
yy
correctly and fastened securely. If they
are not fastened securely enough, the
TV may tilt forward after being installed.
Do not use too much force and over
tighten the screws; otherwise screw may
be damaged and not tighten correctly.
ENGLISH
ENG
Setting up the TV
12
ASSEMBLING AND PREPARING
ENGLISH
ENG
To detach the stand,
1
4 EA
M4 x 30
Caution
When attaching the stand to the TV
yy
set, place the screen facing down on a
cushioned table or flat surface to protect
the screen from scratches.
2
NOTE
Protection cover
This will protect the opening from accuyy
mulating dust and dirt.
When installing the wall mounting
yy
bracket, use the Protection cover.
3
2 EA
M4 x 30
Caution
Tighten the screws firmly to prevent
yy
the TV from tilting forward. Do not over
tighten.
ASSEMBLING AND PREPARING
1 Install the Power Cord Holder and Power
Cord. It will help prevent the power cable from
being removed by accident.
Power Cord Holder
2 Gather and bind the cables with the Cable
Holder.
Cable Holder
Caution
yy
Do not move the TV by holding the cable
holder and power cord holder, as the cable
holders may break, and injuries and damage
to the TV may occur.
ENGLISH
ENG
Tidying cables
13
14
ASSEMBLING AND PREPARING
ENGLISH
ENG
Mounting on a table
Securing the TV to a wall (Depending on model)
1 Lift and tilt the TV into its upright position on a
table.
- Leave a 10 cm (minimum) space from the
wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
Caution
Do not place the TV near or on sources
yy
of heat, as this may result in fire or other
damage.
the TV.
- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
NOTE
yy
Swivel 20 degrees to the left or right and
adjust the angle of the TV to suit your
view.
20
1 Insert and tighten the eye-bolts on the back of
20
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
Caution
Make sure that children do not climb on
yy
or hang on the TV.
Caution
When adjusting the angle of the product,
yy
watch out for your fingers.
»»
Personal injury may occur if hands or
fingers are pinched. If the product is tilted too
much, it may fall, causing damage or injury.
NOTE
Use a platform or cabinet that is strong
yy
and large enough to support the TV
securely.
ASSEMBLING AND PREPARING
A
Attach a wall mount bracket at the rear of the TV
carefully and install the wall mount bracket on a
solid wall perpendicular to the floor. When you
attach the TV to other building materials, please
contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described in
the following table.
Separate purchase(Wall Mounting Bracket)
Model
42/50PA45**
42/50PA49**
50PA65**
60PA65**
VESA (A x B)
Standard screw
Number of screws
Wall mount
bracket
400 x 400
M6
4
PSW400B
600 x 400
M8
4
PSW600B
PSW420BX
PSW620BX
B
Caution
Disconnect the power first, and then
yy
move or install the TV. Otherwise electric
shock may occur.
If you install the TV on a ceiling or slanted
yy
wall, it may fall and result in severe injury.
Use an authorized LG wall mount bracket
and contact the local dealer or qualified
personnel.
Do not over tighten the screws as this
yy
may cause damage to the TV and void
your warranty.
Use the screws and wall mount bracket
yy
that meet the VESA standard. Any
damages or injuries by misuse or using
an improper accessory are not covered
by the manufacturer’s warranty.
NOTE
Use the screws that are listed on the
yy
VESA standard screw specifications.
The wall mount kit includes an installation
yy
manual and necessary parts.
The length of screws may differ
yy
depending on the wall mount. Make sure
to use the proper length.
For more information, refer to the manual
yy
supplied with the wall mount bracket.
ENGLISH
ENG
Mounting on a wall
15
16
REMOTE CONTROL
ENGLISH
ENG
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA)
matching and ends to the label inside the compartment, and close the
battery cover. Be sure to point the remote control to the remote control sensor on
the TV.
or
To remove the batteries, perform the installation actions in reverse.
Caution
Do not mix old and new batteries, as this may damage the remote control.
yy
In Analogue TV and in some countries, some remote control buttons may not work.
yy
POWER
ENERGY
TV/RAD
SAVING
GUIDE INFO
RATIO
INPUT
LIST
Q.VIEW
SETTINGS
Q.MENU
OK
EXIT
FAV
P
MUTE
P
A
G
E
or
RATIO
INPUT ENERGY
TV/
RAD
SAVING
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
FAV
INFO
P
P
A
G
E
(POWER)
ENERGY SAVING
INPUT
TV/RAD
Number buttons
LIST
Q.VIEW
+FAV
Turns the TV on or off.
Adjusts the brightness of the screen to reduce energy consumption .
Changes the input source; Turns the TV on .
Selects Radio, TV and DTV programme.
Enters numbers.
Accesses the saved programme list.
Returns to the previously viewed programme.
Adjusts the volume level.
Accesses your favourite programme list.
MUTE
P∧∨ (P + -)
PAGE
GUIDE
1 SETTINGS
Q. MENU
Navigation buttons
(up/down/left/right)
OK
Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next screen.
Shows programme guide.
Accesses the main menus, or saves your input and exit the menus.
Accesses the quick menus.
Scrolls through menus or options.
INFO
EXIT
Coloured buttons
1 TELETEXT
BUTTONS
SUBTITLE
Control buttons
( , , ,
,
)
SIMPLINK
MUTE
SETTINGS
GUIDE
Q.MENU
OK
EXIT
1
AV MODE
RATIO
AV MODE
(Depending on model)
Selects menus or options and confirms your input.
Returns to the previous level.
Views the information of the current programme and screen.
Clears all on-screen displays and return to TV viewing.
These access special functions in some menus.
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
Recalls your preferred subtitle in digital mode.
Controls the MY MEDIA menus, or the SIMPLINK compatible devices
(USB,SIMPLINK).
Accesses the AV devices connected with the HDMI cable through HDMICEC.
Opens the SIMPLINK menu.
Resizes an image.
Selects an AV mode
WATCHING TV
Connecting an antenna
Connect an antenna to watch TV while referring to
the following.
To prevent damage do not connect to the mains
outlet until all connections are made between the
devices.
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
NOTE
Use a signal splitter to use more than 2
yy
TVs.
If the image quality is poor, install a signal
yy
amplifier properly to improve the image
quality.
If the image quality is poor with an
yy
antenna connected, aim the antenna to
the correct direction.
An antenna cable and converter are not
yy
supplied.
Turning the TV on for the first
time
When you turn the TV on for the first time, the
Initial setting screen appears. Select a language
and customize the basic settings.
1 Connect the power cord to a power outlet.
2 In Standby mode, press
the TV on.
(POWER) to turn
The Initial setting screen appears if you turn
the TV on for the first time.
NOTE
You can also access Factory Reset by
yy
accessing OPTION in the main menus.
3 Follow the on-screen instructions to customize
your TV settings according to your preferences.
Language
Selects a language to display.

Mode Setting

Country

Time Zone

Auto Tuning
Selects Home Use for the
Home environment.
Selects a country to display.
(Except Israel)
Selects a Time Zone to
display.(Only Australia)
Scans and saves available
channels automatically.
NOTE
DTV mode control buttons may not
yy
function based on country broadcasting
circumstances. (Only DTV)
In country that Digital broadcasting
yy
regulation isn’t fixed, some DTV function
may not work depending on digital
broadcasting circumstances. (Only DTV)
To display images in the best quality for
yy
your home environment, select Home
Use.
yyStore Demo is suitable for the retail
environment.
If you select Store Demo, the any
yy
customized settings will switch back to
the default settings of Store Demo in 5
minutes.
4 When the basic settings are complete,
press OK.
NOTE
yy
If you do not complete the Initial setting, it
will appear whenever the TV turns on.
yy
Disconnect the power cord from the
power outlet when you do not use the TV
for a long period of time.
5 To turn the TV off, press
(POWER) .
ENGLISH
ENG
WATCHING TV
17
18
MAKING CONNECTIONS
ENGLISH
ENG
MAKING CONNECTIONS
Connect various external devices to the TV and switch input modes to select an external device. For more
information on external device’s connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices.
NOTE
If you record a TV programme on a DVD recorder or VCR, make sure to connect the TV
yy
signal input cable to the TV through a DVD recorder or VCR. For more information on
recording, refer to the manual provided with the connected device.
The external device connection may differ from the model.
yy
Connect external devices to the TV regardless of the order of the TV port.
yy
Connecting your Unit
yyImage shown may differ from your TV
yyTo connect additional equipment, see the External equipment Setup section in CD Manual.
2
VCR Connection
VCR back
4
USB Connection
or
1
DVD/STB back
2
DVD/STB
3
Power Cord
Antenna
Connection
ENTERTAINMENT
Connecting USB storage devices
USB IN
Connect USB storage devices such as a USB
flash memory, external hard drive to the TV and
use multimedia features (See “Browsing files” on
page 20).
Connect a USB flash memory or USB memory
card reader to the TV as shown on the following
illustration. The My media screen appears, “POP
UP MENU” will not be displayed while the OSD
including Menu, EPG or Schedule list is activated.
or
To disconnect a USB storage device, make sure to
end the connection properly to prevent damages
to the TV or files.
1 Press Q.MENU to access the quick menus.
2 Press the Navigation buttons to scroll to USB
Device and press OK.
3 When pop-up window appears then press OK.
4 Disconnect the USB storage device only when
the message says that it is safe to remove.
Caution
yy
Do not turn the TV off or remove a USB
storage device while the USB storage
device is connected to the TV, as this
could result in loss of files or damage to
the USB storage device.
yy
Back up your files saved on a USB storage device frequently, as you may lose
or damage the files and this may be not
covered by the manufacturer’s warranty.
Tips for using USB storage devices
yy
Only a USB storage device is recognizable.
yy
If the USB storage device is connected
through a USB hub, the device is not recognizable.
yy
A USB storage device using an automatic
recognition programme may not be recognized.
yy
A USB storage device which uses its own
driver may not be recognized.
yy
The recognition speed of a USB storage
device may depend on each device.
yy
Please do not turn off the TV or unplug the
USB device when the connected USB storage device is working. When such device is
suddenly separated or unplugged, the stored
files or the USB storage device may be damaged.
yy
Please do not connect the USB storage
device which was artificially manoeuvred on
the PC. The device may cause the product to
malfunction or fail to be played. Never forget
to use only a USB storage device which has
normal music files, image files or movie files.
yy
Please use only a USB storage device which
was formatted as a FAT32 file system, NTFS
file system provided with the Windows operating system. In case of a storage device
formatted as a different utility programme
which is not supported by Windows, it may
not be recognized.
yy
Please connect power to a USB storage
device(over 0.5 A) which requires an external
power supply. If not, the device may not be
recognized.
yy
Please connect a USB storage device with
the cable offered by the device maker.
yy
Some USB storage devices may not be supported or operated smoothly.
yy
File alignment method of USB storage
device is similar to Window XP and filename
can recognize up to 100 English characters.
yy
Be sure to back up important files since data
stored in a USB memory device may be
damaged. We will not be responsible for any
data loss.
yy
If the USB HDD does not have an external
power source, the USB device may not be
detected. So be sure to connect the external
power source.
ENGLISH
ENG
ENTERTAINMENT
19
20
ENTERTAINMENT
ENGLISH
ENG
- Please use a power adaptor for an external
power source. We do not guarantee an USB
cable for an external power source.
yy
If your USB memory device has multiple
partitions, or if you use a USB multi-card
reader, you can use up to 4 partitions or USB
memory devices.
yy
If a USB memory device is connected to a
USB multi-card reader, its volume data may
not be detected.
yy
If the USB memory device does not work
properly, disconnect and reconnect it.
yy
How fast a USB memory device is detected
differs from device to device.
yy
If the USB is connected in Standby Mode,
specific hard disk will automatically be
loaded when the TV is turned on.
yy
The recommended capacity is 1 TB or less
for a USB external hard disk and 32 GB or
less for USB memory.
yy
Any device with more than the recommended
capacity may not work properly.
yy
If a USB external hard disk with a “Energy
Saving” function does not work, turn the
hard disk off and on again to make it work
properly.
yy
USB storage devices below USB 2.0 are
supported as well. But they may not work
properly in the movie list.
yy
Maximum of 999 folders or files can be recognized under one folder.
yy
The file arrangement of the USB storage
device is similar to that of Windows XP and
supports up to 100 alphabetical characters.
yy
If there are a lot of folders or files all within
one folder, the device may not be able to
access these properly.
Browsing files
Access the photo, music, or movie lists and browse
files.
1 Connect a USB storage device.
2 Press SETTINGS to scroll to main menus.
3 Press the Navigation buttons to scroll to My
Media and press OK.
4 Press Navigation buttons to scroll to Photo
List, Music List, or Movie List and press OK.
USB External
Movie List
Photo List
Music List
2
1
Page 1/1
Photo List
USB External
001
002
010
011
Drive1
003
004
005
006
012
013
014
015
Move
To Music List
Page 1/1
Change Numbers
View
007
P
008
Page Change
Mark Mode
009
4
5
FAV Mark
Exit
3
No.
Description
1
Moves to upper level folder
2
Current page/Total pages
3
4
5
Buttom
Green
button
Yellow
button
Blue
button
Corresponding buttons on the
remote control
Current page/ total pages of
contents under the folder
focused on 1
Contents under the folder
focused on 1
Description
Repeatedly, press the GREEN button to
converted to Photo List->Music List,
Music List->Movie List or Movie List>Photo List.
A method to view in 5 large thumbnail or
simple list.
Convert to Mark Mode.
TROUBLESHOOTING
21
ENGLISH
ENG
TROUBLESHOOTING
General
Problem
Solution
Cannot control the TV with the
remote control.
yyCheck the remote control sensor on the product and try again.
yyCheck if there is any obstacle between the product and the remote control.
to
yyCheck if the batteries are still working and properly installed ( to ,
No image display and no sound is
produced.
yyCheck if the product is turned on.
yyCheck if the power cord is connected to a wall outlet.
yyCheck if there is a problem in the wall outlet by connecting other products.
Image appears slowly when the TV
turns on.
yyThe image is muted during the product start up process. This is normal. If the
image does not appear in a few minutes, unplug the TV for 30 seconds and try
again. If the image still does not appear, contact the authorized service centre
in your local area.
Cannot connect external devices.
yySee "Connection Overview" and connect an external device.
The TV turns off suddenly.
yyCheck the power control settings. The power supply may be interrupted.
yyCheck if the Auto sleep feature is activated in the Time settings.
See "Sleep Timer".
yyIf there is no signal while the TV is on, the TV will turn off automatically after 15
minutes of inactivity.
).
Audio
Problem
Solution
No sound is produced while images
are displaying.
+ or - button.
yyPress
yyCheck if the sound is muted by pressing MUTE.
yyScroll to other channels. There may a problem with the broadcast.
yyCheck if the audio cables are connected properly.
One of the speakers produce noises
or does not produce sound.
yyA change in ambient humidity or temperature may result in an unusual noise
when the product turns on or off.
yyThere is no problem with your product.
Video
Problem
Solution
An image displays in black and
white or the colour quality is poor.
yyAdjust the colour setting in the Picture menu.
yyKeep a sufficient distance between this product and other electronic products.
yyScroll to other channels. There may a problem with the broadcast.
Horizontal or vertical bars appears
or images blur
yyCheck if there are local interferences such as an electrical appliance or power
tool.
Lines or streaks appear on images
yyCheck the antenna or aim the antenna to the proper direction.
Afterimages (ghosts) appear when
the product turns off
yyPixels may have been damaged from a fixed image displayed for a long time
(image burn). Use a screen saver to prevent the pixel damage on the screen.
The power is on but the screen
appears extremely dark.
yyAdjust the brightness and contrast in the Picture menu.
“No Signal” appears on the screen.
yyCheck if the signal cable is connected between the TV and products properly.
yyCheck the selected input source by pressing INPUT.
Black spots appear on the screen.
yySeveral pixels in red, green, white, or black may appear on the screen that can
attribute to the characteristics of the panel.
This is normal.
The display offset is wrong.
yyAdjust the position setting in the Picture menu.
yyCheck if the video card resolution and frequency are supported by the product.
If the frequency is out of range, set to the recommended resolution using the
display settings on the external device.
Thin lines appear in the background yyCheck the video cable connections.
of the screen.
Horizontal noises appear or
characters blur.
yyAdjust the Phase setting in the Picture menu.
See "SCREEN".
The reception on some channels is
poor
yyScroll to other channels. There may a problem with the broadcast.
yyThe station signal may be weak. Aim the antenna to the proper direction.
yyCheck if there is local interference such as an electrical appliance or power tool.
22
TROUBLESHOOTING / SPECIFICATION
Pentouch
ENGLISH
ENG
Problem
Solution
The touch pen does not work.
yyCheck that you used the remote control to enter Pentouch mode.
yyCheck that the Pentouch dongle is connected to the computer and the red LED
is on.
yyPress the Touch Home button on the touch pen to check that it is powered on.
yyCheck that the touch pen is paired for use. (The touch pen is correctly paired
if the red LED is on once when you press the Touch Home button on the touch
pen.)
yySet the computer screen to display only on the TV.
The TV screen doesn’t look normal yyA Check that the computer is correctly connected to the TV.
when using Pentouch.
yyA Check that you are using the optimal resolution.
yySet the aspect ratio on the TV to Just Scan.
The touch pen is touched on wrong yySet the computer screen to display only on the TV.
positions.
yyIf the point you touch on the TV screen using the touch pen and the point
indicated as touched on the computer screen do not match when the computer
and the TV are connected by a PC signal (RGB) cable, use the TV remote
control to select [Home] → [PICTURE] → [SCREEN] (RGB) , then select [Auto
Configure] to adjust the screen.
The touch pen movement is not
smooth.
yyCheck whether the computer and the TV are too far from each other. Check
whether there are too many obstructions between the computer and the TV.
yyA Check whether many other applications are running on the computer. (Please
avoid running other applications while using the Pentouch programme.)
SPECIFICATIONS
MODELS
42PA45**
50PA45**
42PA4500-TF / 42PA4520-TC
42PA4500-TM / 42PA4520-TJ
42PA4530-TH
50PA4500-TF / 50PA4520-TC
50PA4500-TM / 50PA4520-TJ
50PA4530-TH
Dimensions
(W x H x D)
With stand
983.6 mm x 655.0 mm x 246.7 mm
1168.0 mm x 758.0 mm x 297.0 mm
Without stand
983.6 mm x 601.3 mm x 58.0 mm
1168.0 mm x 704.0 mm x 53.0 mm
Weight
With stand
Without stand
Power requirement
20.6 kg
19.0 kg
AC 100-240 ~ 50/60 Hz
MODELS
42PA49**
42PA4900-TE / 42PA4900-TL
28.2 kg
25.8 kg
AC 100-240 ~ 50/60 Hz
50PA49**
50PA4900-TE / 50PA4900-TL
Dimensions
(W x H x D)
With stand
983.6 mm x 655.0 mm x 246.7 mm
1168.0 mm x 758.0 mm x 297.0 mm
Without stand
983.6 mm x 601.3 mm x 58.0 mm
1168.0 mm x 704.0 mm x 53.0 mm
Weight
With stand
20.6 kg
28.2 kg
Without stand
19.0 kg
25.8 kg
Power requirement
AC 100-240 ~ 50/60 Hz
MODELS
AC 100-240 ~ 50/60 Hz
50PA65**
60PA65**
50PA6500-TF / 50PA6500-TM
60PA6500-TF / 60PA6500-TM
Dimensions
(W x H x D)
With stand
1168.0 mm x 758.0 mm x 297.0 mm
1386.8 mm x 883.2 mm x 354.7 mm
Without stand
1168.0 mm x 704.0 mm x 53.0 mm
1386.8 mm x 818.2 mm x 53.0 mm
Weight
With stand
28.8 kg
40.6 kg
Without stand
26.4 kg
36.4 kg
Power requirement
AC 100-240 ~ 50/60 Hz
AC 100-240 ~ 50/60 Hz
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
For the power supply and power consumption, refer to the label attached to the product.
SPECIFICATIONS
Environment condition
New Zealand,
Singapore
Operating Humidity
Storage Temperature
0 °C to 40 °C
Less than 80 %
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Television System
Programme Coverage
Australia
Television System
Programme Coverage
Indonesia, Israel,
Myanmar, Sri
Lanka
Television System
Programme Coverage
Vietnam, Malaysia Television System
Programme Coverage
Iran, Algeria,
Tunisia, Digital
model
Television System
Programme Coverage
Analogue model,
India, Thailand,
South Africa, --
Digital TV
Analogue TV
DVB-T
PAL/SECAM-B/G/D/K, PAL-I
UHF 21 to 69
DVB-T
VHF 06 to 12,
UHF 27 to 69
DVB-T
UHF 21 to 69
DVB-T
VHF 6 to 12,
UHF 21 to 69
DVB-T
VHF 5 to 12,
UHF 21 to 69
Television System
-
Programme Coverage
-
External Antenna
Impedance
75 Ω
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
PAL B/B
B/B : VHF/UHF 0 to 75, CATV : 2 to 44
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
PAL/SECAM-B/G/D/K, PAL-I, NTSC-M
BG : VHF/UHF 1 to 69, CATV 01 to 47
I : VHF/UHF 1 to 69, CATV 01 to 47
DK : VHF/UHF 1 to 69, CATV 01 to 47
M : VHF/UHF 2 to 78, CATV 01 to 71
75 Ω
Product specifications shown above may be changed without prior notice due to upgrade of product
functions.
For the power supply and power consumption, refer to the label attached to the product.
ENGLISH
ENG
Operating Temperature
23
24
OPEN SOURCE SOFTWARE NOTICE
ENGLISH
ENG
Open source software notice
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com .
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
An extended Owner’s Manual that contains
information on the advanced features of these
LG TV sets is located on the CD- ROM provided
in an electronic version.
To read these files, you will need to use a
Personal Computer (PC) equipped with a CDROM drive.
Re co rd t h e m o d e l n u m b e r a n d s e r i a l
number of the TV.
Refer to the label on the back cover and
quote this information to your dealer when
requiring any service.
Model :
Serial No. :
(Only DTV)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising